david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
main
mibs/MIBS/ALARM-MIB

1192 lines
36 KiB
Plaintext
Raw Permalink Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
ALARM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Integer32, Unsigned32, Gauge32,
TimeTicks, Counter32, Counter64,
IpAddress, Opaque, mib-2,
zeroDotZero
FROM SNMPv2-SMI -- [RFC2578]
DateAndTime,
RowStatus, RowPointer,
TEXTUAL-CONVENTION
FROM SNMPv2-TC -- [RFC2579]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB -- [RFC3291]
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
ZeroBasedCounter32
FROM RMON2-MIB; -- [RFC2021]
alarmMIB MODULE-IDENTITY
LAST-UPDATED "200409090000Z" -- September 09, 2004
ORGANIZATION "IETF Distributed Management Working Group"
CONTACT-INFO
"WG EMail: disman@ietf.org
Subscribe: disman-request@ietf.org
http://www.ietf.org/html.charters/disman-charter.html
Chair: Randy Presuhn
randy_presuhn@mindspring.com
Editors: Sharon Chisholm
Nortel Networks
PO Box 3511 Station C
Ottawa, Ont. K1Y 4H7
Canada
schishol@nortelnetworks.com
Dan Romascanu
Avaya
Atidim Technology Park, Bldg. #3
Tel Aviv, 61131
Israel
Tel: +972-3-645-8414
Email: dromasca@avaya.com"
DESCRIPTION
"The MIB module describes a generic solution
to model alarms and to store the current list
of active alarms.
Copyright (C) The Internet Society (2004). The
initial version of this MIB module was published
in RFC 3877. For full legal notices see the RFC
itself. Supplementary information may be available on:
http://www.ietf.org/copyrights/ianamib.html"
REVISION "200409090000Z" -- September 09, 2004
DESCRIPTION
"Initial version, published as RFC 3877."
::= { mib-2 118 }
alarmObjects OBJECT IDENTIFIER ::= { alarmMIB 1 }
alarmNotifications OBJECT IDENTIFIER ::= { alarmMIB 0 }
alarmModel OBJECT IDENTIFIER ::= { alarmObjects 1 }
alarmActive OBJECT IDENTIFIER ::= { alarmObjects 2 }
alarmClear OBJECT IDENTIFIER ::= { alarmObjects 3 }
-- Textual Conventions
-- ResourceId is intended to be a general textual convention
-- that can be used outside of the set of MIBs related to
-- Alarm Management.
ResourceId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A unique identifier for this resource.
The type of the resource can be determined by looking
at the OID that describes the resource.
Resources must be identified in a consistent manner.
For example, if this resource is an interface, this
object MUST point to an ifIndex and if this resource
is a physical entity [RFC2737], then this MUST point
to an entPhysicalDescr, given that entPhysicalIndex
is not accessible. In general, the value is the
name of the instance of the first accessible columnar
object in the conceptual row of a table that is
meaningful for this resource type, which SHOULD
be defined in an IETF standard MIB."
SYNTAX OBJECT IDENTIFIER
-- LocalSnmpEngineOrZeroLenStr is intended to be a general
-- textual convention that can be used outside of the set of
-- MIBs related to Alarm Management.
LocalSnmpEngineOrZeroLenStr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An SNMP Engine ID or a zero-length string. The
instantiation of this textual convention will provide
guidance on when this will be an SNMP Engine ID and
when it will be a zero lengths string"
SYNTAX OCTET STRING (SIZE(0 | 5..32))
-- Alarm Model
alarmModelLastChanged OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the last
creation, deletion or modification of an entry in
the alarmModelTable.
If the number and content of entries has been unchanged
since the last re-initialization of the local network
management subsystem, then the value of this object
MUST be zero."
::= { alarmModel 1 }
alarmModelTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlarmModelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of information about possible alarms on the system,
and how they have been modelled."
::= { alarmModel 2 }
alarmModelEntry OBJECT-TYPE
SYNTAX AlarmModelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries appear in this table for each possible alarm state.
This table MUST be persistent across system reboots."
INDEX { alarmListName, alarmModelIndex, alarmModelState }
::= { alarmModelTable 1 }
AlarmModelEntry ::= SEQUENCE {
alarmModelIndex Unsigned32,
alarmModelState Unsigned32,
alarmModelNotificationId OBJECT IDENTIFIER,
alarmModelVarbindIndex Unsigned32,
alarmModelVarbindValue Integer32,
alarmModelDescription SnmpAdminString,
alarmModelSpecificPointer RowPointer,
alarmModelVarbindSubtree OBJECT IDENTIFIER,
alarmModelResourcePrefix OBJECT IDENTIFIER,
alarmModelRowStatus RowStatus
}
alarmModelIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer that acts as an alarm Id
to uniquely identify each alarm
within the named alarm list. "
::= { alarmModelEntry 1 }
alarmModelState OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value of 1 MUST indicate a clear alarm state.
The value of this object MUST be less than the
alarmModelState of more severe alarm states for
this alarm. The value of this object MUST be more
than the alarmModelState of less severe alarm states
for this alarm."
::= { alarmModelEntry 2 }
alarmModelNotificationId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NOTIFICATION-TYPE object identifier of this alarm
state transition. If there is no notification associated
with this alarm state, the value of this object MUST be
'0.0'"
DEFVAL { zeroDotZero }
::= { alarmModelEntry 3 }
alarmModelVarbindIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The index into the varbind listing of the notification
indicated by alarmModelNotificationId which helps
signal that the given alarm has changed state.
If there is no applicable varbind, the value of this
object MUST be zero.
Note that the value of alarmModelVarbindIndex acknowledges
the existence of the first two obligatory varbinds in
the InformRequest-PDU and SNMPv2-Trap-PDU (sysUpTime.0
and snmpTrapOID.0). That is, a value of 2 refers to
the snmpTrapOID.0.
If the incoming notification is instead an SNMPv1 Trap-PDU,
then an appropriate value for sysUpTime.0 or snmpTrapOID.0
shall be determined by using the rules in section 3.1 of
[RFC3584]"
DEFVAL { 0 }
::= { alarmModelEntry 4 }
alarmModelVarbindValue OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value that the varbind indicated by
alarmModelVarbindIndex takes to indicate
that the alarm has entered this state.
If alarmModelVarbindIndex has a value of 0, so
MUST alarmModelVarbindValue.
"
DEFVAL { 0 }
::= { alarmModelEntry 5 }
alarmModelDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A brief description of this alarm and state suitable
to display to operators."
DEFVAL { "" }
::= { alarmModelEntry 6 }
alarmModelSpecificPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If no additional, model-specific Alarm MIB is supported by
the system the value of this object is `0.0'and attempts
to set it to any other value MUST be rejected appropriately.
When a model-specific Alarm MIB is supported, this object
MUST refer to the first accessible object in a corresponding
row of the model definition in one of these model-specific
MIB and attempts to set this object to { 0 0 } or any other
value MUST be rejected appropriately."
DEFVAL { zeroDotZero }
::= { alarmModelEntry 7 }
alarmModelVarbindSubtree OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name portion of each VarBind in the notification,
in order, is compared to the value of this object.
If the name is equal to or a subtree of the value
of this object, for purposes of computing the value
of AlarmActiveResourceID the 'prefix' will be the
matching portion, and the 'indexes' will be any
remainder. The examination of varbinds ends with
the first match. If the value of this object is 0.0,
then the first varbind, or in the case of v2, the
first varbind after the timestamp and the trap
OID, will always be matched.
"
DEFVAL { zeroDotZero }
::= { alarmModelEntry 8 }
alarmModelResourcePrefix OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of AlarmActiveResourceId is computed
by appending any indexes extracted in accordance
with the description of alarmModelVarbindSubtree
onto the value of this object. If this object's
value is 0.0, then the 'prefix' extracted is used
instead.
"
DEFVAL { zeroDotZero }
::= { alarmModelEntry 9 }
alarmModelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Control for creating and deleting entries. Entries may be
modified while active. Alarms whose alarmModelRowStatus is
not active will not appear in either the alarmActiveTable
or the alarmClearTable. Setting this object to notInService
cannot be used as an alarm suppression mechanism. Entries
that are notInService will disappear as described in RFC2579.
This row can not be modified while it is being
referenced by a value of alarmActiveModelPointer. In these
cases, an error of `inconsistentValue' will be returned to
the manager.
This entry may be deleted while it is being
referenced by a value of alarmActiveModelPointer. This results
in the deletion of this entry and entries in the active alarms
referencing this entry via an alarmActiveModelPointer.
As all read-create objects in this table have a DEFVAL clause,
there is no requirement that any object be explicitly set
before this row can become active. Note that a row consisting
only of default values is not very meaningful."
::= { alarmModelEntry 10 }
-- Active Alarm Table --
alarmActiveLastChanged OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the last
creation or deletion of an entry in the alarmActiveTable.
If the number of entries has been unchanged since the
last re-initialization of the local network management
subsystem, then this object contains a zero value."
::= { alarmActive 1 }
alarmActiveOverflow OBJECT-TYPE
SYNTAX Counter32
UNITS "active alarms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of active alarms that have not been put into
the alarmActiveTable since system restart as a result
of extreme resource constraints."
::= { alarmActive 5 }
alarmActiveTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlarmActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Active Alarms entries."
::= { alarmActive 2 }
alarmActiveEntry OBJECT-TYPE
SYNTAX AlarmActiveEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries appear in this table when alarms are raised. They
are removed when the alarm is cleared.
If under extreme resource constraint the system is unable to
add any more entries into this table, then the
alarmActiveOverflow statistic will be increased by one."
INDEX { alarmListName, alarmActiveDateAndTime,
alarmActiveIndex }
::= { alarmActiveTable 1 }
AlarmActiveEntry ::= SEQUENCE {
alarmListName SnmpAdminString,
alarmActiveDateAndTime DateAndTime,
alarmActiveIndex Unsigned32,
alarmActiveEngineID LocalSnmpEngineOrZeroLenStr,
alarmActiveEngineAddressType InetAddressType,
alarmActiveEngineAddress InetAddress,
alarmActiveContextName SnmpAdminString,
alarmActiveVariables Unsigned32,
alarmActiveNotificationID OBJECT IDENTIFIER,
alarmActiveResourceId ResourceId,
alarmActiveDescription SnmpAdminString,
alarmActiveLogPointer RowPointer,
alarmActiveModelPointer RowPointer,
alarmActiveSpecificPointer RowPointer }
alarmListName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The name of the list of alarms. This SHOULD be the same as
nlmLogName if the Notification Log MIB [RFC3014] is supported.
This SHOULD be the same as, or contain as a prefix, the
applicable snmpNotifyFilterProfileName if the
SNMP-NOTIFICATION-MIB DEFINITIONS [RFC3413] is supported.
An implementation may allow multiple named alarm lists, up to
some implementation-specific limit (which may be none). A
zero-length list name is reserved for creation and deletion
by the managed system, and MUST be used as the default log
name by systems that do not support named alarm lists."
::= { alarmActiveEntry 1 }
alarmActiveDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local date and time when the error occurred.
This object facilitates retrieving all instances of
alarms that have been raised or have changed state
since a given point in time.
Implementations MUST include the offset from UTC,
if available. Implementation in environments in which
the UTC offset is not available is NOT RECOMMENDED."
::= { alarmActiveEntry 2 }
alarmActiveIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A strictly monotonically increasing integer which
acts as the index of entries within the named alarm
list. It wraps back to 1 after it reaches its
maximum value."
::= { alarmActiveEntry 3 }
alarmActiveEngineID OBJECT-TYPE
SYNTAX LocalSnmpEngineOrZeroLenStr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The identification of the SNMP engine at which the alarm
originated. If the alarm is from an SNMPv1 system this
object is a zero length string."
::= { alarmActiveEntry 4 }
alarmActiveEngineAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates what type of address is stored in
the alarmActiveEngineAddress object - IPv4, IPv6, DNS, etc."
::= { alarmActiveEntry 5 }
alarmActiveEngineAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the SNMP engine on which the alarm is
occurring.
This object MUST always be instantiated, even if the list
can contain alarms from only one engine."
::= { alarmActiveEntry 6 }
alarmActiveContextName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the SNMP MIB context from which the alarm came.
For SNMPv1 alarms this is the community string from the Trap.
Note that care MUST be taken when selecting community
strings to ensure that these can be represented as a
well-formed SnmpAdminString. Community or Context names
that are not well-formed SnmpAdminStrings will be mapped
to zero length strings.
If the alarm's source SNMP engine is known not to support
multiple contexts, this object is a zero length string."
::= { alarmActiveEntry 7 }
alarmActiveVariables OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of variables in alarmActiveVariableTable for this
alarm."
::= { alarmActiveEntry 8 }
alarmActiveNotificationID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The NOTIFICATION-TYPE object identifier of the alarm
state transition that is occurring."
::= { alarmActiveEntry 9 }
alarmActiveResourceId OBJECT-TYPE
SYNTAX ResourceId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the resource under alarm.
If there is no corresponding resource, then
the value of this object MUST be 0.0."
::= { alarmActiveEntry 10 }
alarmActiveDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object provides a textual description of the
active alarm. This text is generated dynamically by the
notification generator to provide useful information
to the human operator. This information SHOULD
provide information allowing the operator to locate
the resource for which this alarm is being generated.
This information is not intended for consumption by
automated tools."
::= { alarmActiveEntry 11 }
alarmActiveLogPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A pointer to the corresponding row in a
notification logging MIB where the state change
notification for this active alarm is logged.
If no log entry applies to this active alarm,
then this object MUST have the value of 0.0"
::= { alarmActiveEntry 12 }
alarmActiveModelPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A pointer to the corresponding row in the
alarmModelTable for this active alarm. This
points not only to the alarm model being
instantiated, but also to the specific alarm
state that is active."
::= { alarmActiveEntry 13 }
alarmActiveSpecificPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If no additional, model-specific, Alarm MIB is supported by
the system this object is `0.0'. When a model-specific Alarm
MIB is supported, this object is the instance pointer to the
specific model-specific active alarm list."
::= { alarmActiveEntry 14 }
-- Active Alarm Variable Table --
alarmActiveVariableTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlarmActiveVariableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of variables to go with active alarm entries."
::= { alarmActive 3 }
alarmActiveVariableEntry OBJECT-TYPE
SYNTAX AlarmActiveVariableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entries appear in this table when there are variables in
the varbind list of a corresponding alarm in
alarmActiveTable.
Entries appear in this table as though
the trap/notification had been transported using a
SNMPv2-Trap-PDU, as defined in [RFC3416] - i.e., the
alarmActiveVariableIndex 1 will always be sysUpTime
and alarmActiveVariableIndex 2 will always be
snmpTrapOID.
If the incoming notification is instead an SNMPv1 Trap-PDU and
the value of alarmModelVarbindIndex is 1 or 2, an appropriate
value for sysUpTime.0 or snmpTrapOID.0 shall be determined
by using the rules in section 3.1 of [RFC3584]."
INDEX { alarmListName, alarmActiveIndex,
alarmActiveVariableIndex }
::= { alarmActiveVariableTable 1 }
AlarmActiveVariableEntry ::= SEQUENCE {
alarmActiveVariableIndex Unsigned32,
alarmActiveVariableID OBJECT IDENTIFIER,
alarmActiveVariableValueType INTEGER,
alarmActiveVariableCounter32Val Counter32,
alarmActiveVariableUnsigned32Val Unsigned32,
alarmActiveVariableTimeTicksVal TimeTicks,
alarmActiveVariableInteger32Val Integer32,
alarmActiveVariableOctetStringVal OCTET STRING,
alarmActiveVariableIpAddressVal IpAddress,
alarmActiveVariableOidVal OBJECT IDENTIFIER,
alarmActiveVariableCounter64Val Counter64,
alarmActiveVariableOpaqueVal Opaque }
alarmActiveVariableIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A strictly monotonically increasing integer, starting at
1 for a given alarmActiveIndex, for indexing variables
within the active alarm variable list. "
::= { alarmActiveVariableEntry 1 }
alarmActiveVariableID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The alarm variable's object identifier."
::= { alarmActiveVariableEntry 2 }
alarmActiveVariableValueType OBJECT-TYPE
SYNTAX INTEGER {
counter32(1),
unsigned32(2),
timeTicks(3),
integer32(4),
ipAddress(5),
octetString(6),
objectId(7),
counter64(8),
opaque(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the value. One and only one of the value
objects that follow is used for a given row in this table,
based on this type."
::= { alarmActiveVariableEntry 3 }
alarmActiveVariableCounter32Val OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'counter32'."
::= { alarmActiveVariableEntry 4 }
alarmActiveVariableUnsigned32Val OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'unsigned32'."
::= { alarmActiveVariableEntry 5 }
alarmActiveVariableTimeTicksVal OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'timeTicks'."
::= { alarmActiveVariableEntry 6 }
alarmActiveVariableInteger32Val OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'integer32'."
::= { alarmActiveVariableEntry 7 }
alarmActiveVariableOctetStringVal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..65535))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'octetString'."
::= { alarmActiveVariableEntry 8 }
alarmActiveVariableIpAddressVal OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'ipAddress'."
::= { alarmActiveVariableEntry 9 }
alarmActiveVariableOidVal OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'objectId'."
::= { alarmActiveVariableEntry 10 }
alarmActiveVariableCounter64Val OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'counter64'."
::= { alarmActiveVariableEntry 11 }
alarmActiveVariableOpaqueVal OBJECT-TYPE
SYNTAX Opaque (SIZE(0..65535))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value when alarmActiveVariableType is 'opaque'.
Note that although RFC2578 [RFC2578] forbids the use
of Opaque in 'standard' MIB modules, this particular
usage is driven by the need to be able to accurately
represent any well-formed notification, and justified
by the need for backward compatibility."
::= { alarmActiveVariableEntry 12 }
-- Statistics --
alarmActiveStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlarmActiveStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the alarm statistics
information."
::= { alarmActive 4 }
alarmActiveStatsEntry OBJECT-TYPE
SYNTAX AlarmActiveStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics on the current active alarms."
INDEX { alarmListName }
::= { alarmActiveStatsTable 1 }
AlarmActiveStatsEntry ::=
SEQUENCE {
alarmActiveStatsActiveCurrent Gauge32,
alarmActiveStatsActives ZeroBasedCounter32,
alarmActiveStatsLastRaise TimeTicks,
alarmActiveStatsLastClear TimeTicks
}
alarmActiveStatsActiveCurrent OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of currently active alarms on the system."
::= { alarmActiveStatsEntry 1 }
alarmActiveStatsActives OBJECT-TYPE
SYNTAX ZeroBasedCounter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of active alarms since system restarted."
::= { alarmActiveStatsEntry 2 }
alarmActiveStatsLastRaise OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the last
alarm raise for this alarm list.
If no alarm raises have occurred since the
last re-initialization of the local network management
subsystem, then this object contains a zero value."
::= { alarmActiveStatsEntry 3 }
alarmActiveStatsLastClear OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the last
alarm clear for this alarm list.
If no alarm clears have occurred since the
last re-initialization of the local network management
subsystem, then this object contains a zero value."
::= { alarmActiveStatsEntry 4 }
-- Alarm Clear
alarmClearMaximum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum number of cleared
alarms to store in the alarmClearTable. When this
number is reached, the cleared alarms with the
earliest clear time will be removed from the table."
::= { alarmClear 1 }
alarmClearTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlarmClearEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on
cleared alarms."
::= { alarmClear 2 }
alarmClearEntry OBJECT-TYPE
SYNTAX AlarmClearEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information on a cleared alarm."
INDEX { alarmListName, alarmClearDateAndTime,
alarmClearIndex }
::= { alarmClearTable 1 }
AlarmClearEntry ::=
SEQUENCE {
alarmClearIndex Unsigned32,
alarmClearDateAndTime DateAndTime,
alarmClearEngineID LocalSnmpEngineOrZeroLenStr,
alarmClearEngineAddressType InetAddressType,
alarmClearEngineAddress InetAddress,
alarmClearContextName SnmpAdminString,
alarmClearNotificationID OBJECT IDENTIFIER,
alarmClearResourceId ResourceId,
alarmClearLogIndex Unsigned32,
alarmClearModelPointer RowPointer
}
alarmClearIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An integer which acts as the index of entries within
the named alarm list. It wraps back to 1 after it
reaches its maximum value.
This object has the same value as the alarmActiveIndex that
this alarm instance had when it was active."
::= { alarmClearEntry 1 }
alarmClearDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local date and time when the alarm cleared.
This object facilitates retrieving all instances of
alarms that have been cleared since a given point in time.
Implementations MUST include the offset from UTC,
if available. Implementation in environments in which
the UTC offset is not available is NOT RECOMMENDED."
::= { alarmClearEntry 2 }
alarmClearEngineID OBJECT-TYPE
SYNTAX LocalSnmpEngineOrZeroLenStr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The identification of the SNMP engine at which the alarm
originated. If the alarm is from an SNMPv1 system this
object is a zero length string."
::= { alarmClearEntry 3 }
alarmClearEngineAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates what type of address is stored in
the alarmActiveEngineAddress object - IPv4, IPv6, DNS, etc."
::= { alarmClearEntry 4 }
alarmClearEngineAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Address of the SNMP engine on which the alarm was
occurring. This is used to identify the source of an SNMPv1
trap, since an alarmActiveEngineId cannot be extracted from the
SNMPv1 trap PDU.
This object MUST always be instantiated, even if the list
can contain alarms from only one engine."
::= { alarmClearEntry 5 }
alarmClearContextName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the SNMP MIB context from which the alarm came.
For SNMPv1 traps this is the community string from the Trap.
Note that care needs to be taken when selecting community
strings to ensure that these can be represented as a
well-formed SnmpAdminString. Community or Context names
that are not well-formed SnmpAdminStrings will be mapped
to zero length strings.
If the alarm's source SNMP engine is known not to support
multiple contexts, this object is a zero length string."
::= { alarmClearEntry 6 }
alarmClearNotificationID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The NOTIFICATION-TYPE object identifier of the alarm
clear."
::= { alarmClearEntry 7 }
alarmClearResourceId OBJECT-TYPE
SYNTAX ResourceId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the resource that was under alarm.
If there is no corresponding resource, then
the value of this object MUST be 0.0."
::= { alarmClearEntry 8 }
alarmClearLogIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This number MUST be the same as the log index of the
applicable row in the notification log MIB, if it exists.
If no log index applies to the trap, then this object
MUST have the value of 0."
::= { alarmClearEntry 9 }
alarmClearModelPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A pointer to the corresponding row in the
alarmModelTable for this cleared alarm."
::= { alarmClearEntry 10 }
-- Notifications
alarmActiveState NOTIFICATION-TYPE
OBJECTS { alarmActiveModelPointer,
alarmActiveResourceId }
STATUS current
DESCRIPTION
"An instance of the alarm indicated by
alarmActiveModelPointer has been raised
against the entity indicated by
alarmActiveResourceId.
The agent must throttle the generation of
consecutive alarmActiveState traps so that there is at
least a two-second gap between traps of this
type against the same alarmActiveModelPointer and
alarmActiveResourceId. When traps are throttled,
they are dropped, not queued for sending at a future time.
A management application should periodically check
the value of alarmActiveLastChanged to detect any
missed alarmActiveState notification-events, e.g.,
due to throttling or transmission loss."
::= { alarmNotifications 2 }
alarmClearState NOTIFICATION-TYPE
OBJECTS { alarmActiveModelPointer,
alarmActiveResourceId }
STATUS current
DESCRIPTION
"An instance of the alarm indicated by
alarmActiveModelPointer has been cleared against
the entity indicated by alarmActiveResourceId.
The agent must throttle the generation of
consecutive alarmActiveClear traps so that there is at
least a two-second gap between traps of this
type against the same alarmActiveModelPointer and
alarmActiveResourceId. When traps are throttled,
they are dropped, not queued for sending at a future time.
A management application should periodically check
the value of alarmActiveLastChanged to detect any
missed alarmClearState notification-events, e.g.,
due to throttling or transmission loss."
::= { alarmNotifications 3 }
-- Conformance
alarmConformance OBJECT IDENTIFIER ::= { alarmMIB 2 }
alarmCompliances OBJECT IDENTIFIER ::= { alarmConformance 1 }
alarmCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for systems supporting
the Alarm MIB."
MODULE -- this module
MANDATORY-GROUPS {
alarmActiveGroup,
alarmModelGroup
}
GROUP alarmActiveStatsGroup
DESCRIPTION
"This group is optional."
GROUP alarmClearGroup
DESCRIPTION
"This group is optional."
GROUP alarmNotificationsGroup
DESCRIPTION
"This group is optional."
::= { alarmCompliances 1 }
alarmGroups OBJECT IDENTIFIER ::= { alarmConformance 2 }
alarmModelGroup OBJECT-GROUP
OBJECTS {
alarmModelLastChanged,
alarmModelNotificationId,
alarmModelVarbindIndex,
alarmModelVarbindValue,
alarmModelDescription,
alarmModelSpecificPointer,
alarmModelVarbindSubtree,
alarmModelResourcePrefix,
alarmModelRowStatus
}
STATUS current
DESCRIPTION
"Alarm model group."
::= { alarmGroups 1}
alarmActiveGroup OBJECT-GROUP
OBJECTS {
alarmActiveLastChanged,
alarmActiveOverflow,
alarmActiveEngineID,
alarmActiveEngineAddressType,
alarmActiveEngineAddress,
alarmActiveContextName,
alarmActiveVariables,
alarmActiveNotificationID,
alarmActiveResourceId,
alarmActiveDescription,
alarmActiveLogPointer,
alarmActiveModelPointer,
alarmActiveSpecificPointer,
alarmActiveVariableID,
alarmActiveVariableValueType,
alarmActiveVariableCounter32Val,
alarmActiveVariableUnsigned32Val,
alarmActiveVariableTimeTicksVal,
alarmActiveVariableInteger32Val,
alarmActiveVariableOctetStringVal,
alarmActiveVariableIpAddressVal,
alarmActiveVariableOidVal,
alarmActiveVariableCounter64Val,
alarmActiveVariableOpaqueVal
}
STATUS current
DESCRIPTION
"Active Alarm list group."
::= { alarmGroups 2}
alarmActiveStatsGroup OBJECT-GROUP
OBJECTS {
alarmActiveStatsActives,
alarmActiveStatsActiveCurrent,
alarmActiveStatsLastRaise,
alarmActiveStatsLastClear
}
STATUS current
DESCRIPTION
"Active alarm summary group."
::= { alarmGroups 3}
alarmClearGroup OBJECT-GROUP
OBJECTS {
alarmClearMaximum,
alarmClearEngineID,
alarmClearEngineAddressType,
alarmClearEngineAddress,
alarmClearContextName,
alarmClearNotificationID,
alarmClearResourceId,
alarmClearLogIndex,
alarmClearModelPointer
}
STATUS current
DESCRIPTION
"Cleared alarm group."
::= { alarmGroups 4}
alarmNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { alarmActiveState, alarmClearState }
STATUS current
DESCRIPTION
"The collection of notifications that can be used to
model alarms for faults lacking pre-existing
notification definitions."
::= { alarmGroups 6 }
END
Reference in New Issue Copy Permalink