mibs/MIBS/adva/F3-EOTDM-MIB

543 lines
18 KiB
Plaintext
Raw Permalink Normal View History

2023-12-05 12:25:34 +01:00
F3-EOTDM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Integer32, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, StorageType, DisplayString, VariablePointer,
TEXTUAL-CONVENTION, TruthValue
FROM SNMPv2-TC
InterfaceIndex
FROM IF-MIB
neIndex, shelfIndex, slotIndex
FROM CM-ENTITY-MIB
fsp150cm
FROM ADVA-MIB
AdminState, OperationalState, SecondaryState
FROM CM-COMMON-MIB;
f3EOTDMMIB MODULE-IDENTITY
LAST-UPDATED "201205100000Z"
ORGANIZATION "ADVA Optical Networking"
CONTACT-INFO
" Kasen Zeng
ADVA Optical Networking, Inc.
Tel:
E-mail: kzeng@advaoptical.com
Postal: 18/F, Maoye Times Square,
Haide 2nd Road, Nanshan District,
Shenzhen, P.R.China 518054"
DESCRIPTION
"This module defines the EOTDM MIB definitions used by
the F3 (FSP150CM/CC) product lines.
Copyright (C) ADVA Optical Networking."
REVISION "201205100000Z"
DESCRIPTION
"Notes from release 201205100000Z,
(1)MIB version ready for release FSP150CM 5.5."
::= {fsp150cm 17}
--
-- OID definitions
--
f3EotdmObjects OBJECT IDENTIFIER ::= {f3EOTDMMIB 1}
f3EotdmConformance OBJECT IDENTIFIER ::= {f3EOTDMMIB 2}
--
-- Textual Conventions
--
VcgType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Describes the VC type in a virtual concatenate group. All VCs in this
group is the same type."
SYNTAX INTEGER {
none (0),
t1 (1),
e1 (2),
t3 (3),
e3 (4),
vc12 (5),
vc3 (6),
vc4 (7),
vt15 (8),
sts1 (9),
sts3c (10)
}
WtrTime ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Wait to restore(WTR) time for LCAS protocol when the dMSU defect
occured (Unit: minute)."
SYNTAX INTEGER (0..12)
HoldOffTime ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Hold off time for LCAS protocol when the dMSU defect occured
(Unit: 100ms)."
SYNTAX INTEGER (0..100)
CtrlState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Discribes the CTRL status of a virtual container in LCAS
control packet:
- ctrlNotAppl: NA: Not applicable, ie, this VC is not allocated
to a VCG or LCAS is disabled
- ctrlFixed: FIXED: This end uses fixed bandwidth (non-LCAS mode)
- ctrlAdd: ADD: This member is about to be added to the group
- ctrlNorm: NORM: Normal transmission
- ctrlEos: EOS: End of Sequence and Normal transmission
- ctrlIdle: IDLE: This member is not part of the group or about
to be removed
- ctrlDnu: DNU: Do Not Use (the payload) the Sk side reported
FAIL status"
SYNTAX INTEGER {
ctrlNotAppl (0),
ctrlFixed (1),
ctrlAdd (2),
ctrlNorm (3),
ctrlEos (4),
ctrlIdle (5),
ctrlDnu (6)
}
LcasSoState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The status of LCAS protocol at the source end of a virtual container:
- srcNotAppl: NA: Not applicable, ie, this VC is not allocated
to a VCG or LCAS is disabled
-srcIdle: IDLE: The VC is not in use or has been removed.
- srcAdd: ADD: The VC is in the process of being added.
May also indicate that the sink end:
- does not have LCAS enabled and this VC is
in use at this end, or
- this VC is not allocated in the service.
- srcNorm: NORM: The VC is in use with a good path to the
sink end.
- srcDnu: DNU: 'Do not use' indicates the VC is in use but
has a failed path to the sink end.
- srcRemove: REMOVE: The VC is being deleted from the service."
SYNTAX INTEGER {
srcNotAppl (0),
srcIdle (1),
srcAdd (2),
srcNorm (3),
srcDnu (4),
srcRemove (5)
}
MstState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Discribes the MST status of a virtual container in LCAS
control packet:
- mstNotAppl: NA: Not applicable, ie, this VC is not allocated
to a VCG or LCAS is disabled
- mstOk: OK: The MST status of this virtual container is OK
- mstFail: FAIL: The MST status of this virtual container is FAIL"
SYNTAX INTEGER {
mstNotAppl (0),
mstOk (1),
mstFail (2)
}
LcasSkState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The status of LCAS protocol at the sink end of a virtual container:
- sinkNotAppl: NA: Not applicable, ie, this VC is not allocated
to a VCG or LCAS is disabled
- sinkIdle: IDLE: The virtual container is not in use.
- sinkOk: OK: Normal incoming signal, or has acknowledged
a request to be added to the service.
- sinkFail: FAIL: Failure condition on incoming signal, or has
acknowledged a request for removal."
SYNTAX INTEGER {
sinkNotAppl (0),
sinkIdle (1),
sinkOk (2),
sinkFail (3)
}
--
-- FSP150 CM EoTDM Configuration Tables
--
--
-- VCG Table
--
vcgTable OBJECT-TYPE
SYNTAX SEQUENCE OF VcgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of entries corresponding to virtual concatenate groups."
::= { f3EotdmObjects 1 }
vcgEntry OBJECT-TYPE
SYNTAX VcgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the vcgTable."
INDEX { neIndex, shelfIndex, slotIndex, vcgIndex }
::= { vcgTable 1 }
VcgEntry ::= SEQUENCE {
vcgIndex Integer32,
vcgIfIndex InterfaceIndex,
vcgAssociatedEthernetPort VariablePointer,
vcgAdminState AdminState,
vcgOperationalState OperationalState,
vcgSecondaryState SecondaryState,
vcgType VcgType,
vcgLcasEnabled TruthValue,
vcgWtrTimer WtrTime,
vcgHoldOffTimer HoldOffTime,
vcgClearWtrTimer INTEGER,
vcgRowStatus RowStatus
}
vcgIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An integer index value used to uniquely identify this vcg within a card."
::= { vcgEntry 1 }
vcgIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object has the same value as ifIndex for vcg."
::= { vcgEntry 2 }
vcgAssociatedEthernetPort OBJECT-TYPE
SYNTAX VariablePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object describes the related Ethernet Port of the vcg."
::= { vcgEntry 3 }
vcgAdminState OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object represents the Administrative State of the vcg."
::= { vcgEntry 4 }
vcgOperationalState OBJECT-TYPE
SYNTAX OperationalState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the Operational State of the vcg."
::= { vcgEntry 5 }
vcgSecondaryState OBJECT-TYPE
SYNTAX SecondaryState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the Secondary State of the vcg."
::= { vcgEntry 6 }
vcgType OBJECT-TYPE
SYNTAX VcgType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of paths in this VCG. All paths in this VCG are the same type.
This is a required field when creating a VCG, and can not be
changed on an existing VCG.
See the definition of VcType for more details."
::= { vcgEntry 7 }
vcgLcasEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provides whether Lcas is enabled/disabled."
::= { vcgEntry 8 }
vcgWtrTimer OBJECT-TYPE
SYNTAX WtrTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies wait to restore(WTR) time for LCAS protocol.
When creating VCG with LCAS enabled, it is the default value,
says 5 minutes. When creating VCG with LCAS disabled, it is 0 (means
that the WTR is disabled)."
::= { vcgEntry 9 }
vcgHoldOffTimer OBJECT-TYPE
SYNTAX HoldOffTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies hold off time for LCAS protocol.
When creating VCG with LCAS enabled, it is the default value,
says 0 ms. When creating VCG with LCAS disabled, it is 0 ms."
::= { vcgEntry 10 }
vcgClearWtrTimer OBJECT-TYPE
SYNTAX INTEGER (0..1)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object will trigger an action.
When writing with '1', a 'clear WTR timer' action for all paths in
the VCG is triggered. Writing '0' is no effect.
When reading, it always returns 0."
::= { vcgEntry 11 }
vcgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of vcgRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
neRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The vcgRowStatus object may be modified if
the associated instance of this object is equal to active(1)."
::= { vcgEntry 12 }
--
-- VCG Member Table
--
vcgMemberTable OBJECT-TYPE
SYNTAX SEQUENCE OF VcgMemberEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of entries corresponding to VCGs. Each entry of the table
represents a path which is allocated to a VCG."
::= { f3EotdmObjects 2 }
vcgMemberEntry OBJECT-TYPE
SYNTAX VcgMemberEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the vcgMemberTable."
INDEX { neIndex, shelfIndex, slotIndex, vcgIndex, vcgMemberIndex }
::= { vcgMemberTable 1 }
VcgMemberEntry ::= SEQUENCE {
vcgMemberIndex Integer32,
vcgMemberIfIndex InterfaceIndex,
vcgMemberRowStatus RowStatus,
vcgMemberSoSendSeq INTEGER,
vcgMemberSoLcasSendCtrl CtrlState,
vcgMemberSoLcasRecvMst MstState,
vcgMemberSoLcasState LcasSoState,
vcgMemberSkRecvSeq INTEGER,
vcgMemberSkRecvExpectSeq INTEGER,
vcgMemberSkLcasRecvCtrl CtrlState,
vcgMemberSkLcasSendMst MstState,
vcgMemberSkLcasState LcasSkState
}
vcgMemberIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An integer index value used to uniquely identify this vcg member."
::= { vcgMemberEntry 1 }
vcgMemberIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object has the same value as ifIndex for
vcg path. An integer index value used to
uniquely identify this vcg path."
::= { vcgMemberEntry 2 }
vcgMemberRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of vcgMemberRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
neRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The vcgMemberRowStatus object may be modified if
the associated instance of this object is equal to active(1)."
::= { vcgMemberEntry 3 }
vcgMemberSoSendSeq OBJECT-TYPE
SYNTAX INTEGER ( -1..63 )
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the source side, this object reports the sequence number sent
to the sink side. The sequence number is determined by the LCAS
protocol (when LCAS is enabled) or by the order that each path was
added into the VCG (when LCAS is disabled). If SQ is invalid,
-1 is returned"
::= { vcgMemberEntry 4 }
vcgMemberSoLcasSendCtrl OBJECT-TYPE
SYNTAX CtrlState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the source side, this object reports the CTRL status which is
sent to the sink side. The CTRL status is determined by the LCAS
protocol.
When LCAS is not used, the value 'ctrlNotAppl' is returned."
::= { vcgMemberEntry 5 }
vcgMemberSoLcasRecvMst OBJECT-TYPE
SYNTAX MstState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the source side, this object reports the member status which is
received from sink side. The member status is determined by the
LCAS protocol.
When LCAS is not used, the value 'mstNotAppl' is returned."
::= { vcgMemberEntry 6 }
vcgMemberSoLcasState OBJECT-TYPE
SYNTAX LcasSoState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reports the current source status of this path as
determined by the LCAS protocol. When LCAS is not in use,
the value 'srcNotAppl' is returned."
::= { vcgMemberEntry 7 }
vcgMemberSkRecvSeq OBJECT-TYPE
SYNTAX INTEGER (-1..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the sink side, this object reports the sequence number which is
received from source side. If SQ is invalid, -1 is returned."
::= { vcgMemberEntry 8 }
vcgMemberSkRecvExpectSeq OBJECT-TYPE
SYNTAX INTEGER (-1..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the sink side, this object reports the sequence number expected.
If LCAS is enabled, this value is -1. Otherwise, it's the order that
each path was added into the VCG, starting from 0.
If SQ is invalid, -1 is returned."
::= { vcgMemberEntry 9 }
vcgMemberSkLcasRecvCtrl OBJECT-TYPE
SYNTAX CtrlState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the sink side, this object reports the CTRL status which is
received from source side. The CTRL status is determined by the
LCAS protocol. When LCAS is not used, the value 'ctrlNotAppl'
is returned."
::= { vcgMemberEntry 10 }
vcgMemberSkLcasSendMst OBJECT-TYPE
SYNTAX MstState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"As the sink side, this object reports the member status which is
sent to source side. The 'member status' is determined by the status
of received path member. When LCAS is not used, the value 'mstNotAppl'
is returned."
::= { vcgMemberEntry 11 }
vcgMemberSkLcasState OBJECT-TYPE
SYNTAX LcasSkState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reports the current sink status of this path as
determined by the LCAS protocol. When LCAS is not in use,
the value 'sinkNotAppl' is returned."
::= { vcgMemberEntry 12 }
--
-- Conformance
--
f3EotdmCompliances OBJECT IDENTIFIER ::= {f3EotdmConformance 1}
f3EotdmGroups OBJECT IDENTIFIER ::= {f3EotdmConformance 2}
f3EotdmCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the f3 Tdm
group."
MODULE -- this module
MANDATORY-GROUPS {
f3EotdmObjectGroup
}
::= { f3EotdmCompliances 1 }
f3EotdmObjectGroup OBJECT-GROUP
OBJECTS {
vcgIndex, vcgIfIndex,
vcgAssociatedEthernetPort, vcgAdminState,
vcgOperationalState, vcgSecondaryState,
vcgType, vcgLcasEnabled,
vcgWtrTimer, vcgHoldOffTimer,
vcgClearWtrTimer, vcgRowStatus,
vcgMemberIndex, vcgMemberIfIndex,
vcgMemberRowStatus, vcgMemberSoSendSeq,
vcgMemberSoLcasSendCtrl, vcgMemberSoLcasRecvMst,
vcgMemberSoLcasState, vcgMemberSkRecvSeq,
vcgMemberSkRecvExpectSeq, vcgMemberSkLcasRecvCtrl,
vcgMemberSkLcasSendMst, vcgMemberSkLcasState
}
STATUS current
DESCRIPTION
"A collection of objects used to manage the f3 Tdm
group."
::= { f3EotdmGroups 1 }
END