david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
main
mibs/MIBS/cisco/CISCO-IETF-ISIS-MIB

3817 lines
122 KiB
Plaintext
Raw Permalink Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
-- *****************************************************************
-- CISCO-IETF-ISIS-MIB.my: Cisco Experimental MIB for IS-IS
--
-- August 2005, Sundar Ramachandran
--
-- Copyright (c) 2005 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************
-- This MIB module is based on the Internet Draft
-- <draft-ietf-isis-wg-mib-16.txt>. In terms of object syntax and
-- semantics, the content of this Cisco MIB is the same as the
-- corresponding Internet Draft revision. This Cisco MIB was created
-- due to the "subject to change" nature of Internet Drafts. This
-- Cisco MIB may later be deprecated, and the stable RFC, which may
-- replace the Internet Draft, may be implemented in its place.
--
-- Caution. This MIB is temporary and experimental. In the future it
-- will be removed from products, perhaps with short notice, in favor
-- of more standard or generic MIBs. Application developers should
-- not depend on long-term access to this MIB.
CISCO-IETF-ISIS-MIB DEFINITIONS ::= BEGIN
IMPORTS
TEXTUAL-CONVENTION, RowStatus, TruthValue
FROM SNMPv2-TC
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32,
Counter32, TimeTicks, NOTIFICATION-TYPE
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
ciscoExperiment
FROM CISCO-SMI
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
IndexIntegerNextFree
FROM DIFFSERV-MIB
InterfaceIndex
FROM IF-MIB
InetAddressType, InetAddress, InetAddressPrefixLength
FROM INET-ADDRESS-MIB;
ciscoIetfIsisMIB MODULE-IDENTITY
LAST-UPDATED "200508161200Z" -- August 16, 2005 12:00:00 GMT
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-clns@cisco.com"
DESCRIPTION
"This document describes a management information base for
the IS-IS Routing protocol, as described in ISO 10589,
when it is used to construct routing tables for IP networks,
as described in RFC 1195. This MIB is entirely based upon
the IETF draft draft-ietf-isis-wg-mib-16."
-- Revision History
REVISION "200508161200Z" -- August 16, 2005 12:00:00 GMT
DESCRIPTION
"Corrected DESCRIPTION clause for ciiAreaAddrTable,
ciiAreaAddrEntry, ciiAreaAddr and for
ciiSysLevelOverloadState based on similar
definitions in draft-ietf-isis-wg-mib-18.txt."
REVISION "200502081200Z" -- 08 February 2005 12:00:00 GMT
DESCRIPTION
"Initial version."
::= { ciscoExperiment 118 }
-- Top-level structure of the MIB
ciscoIetfIsisMIBNotifs OBJECT IDENTIFIER ::= { ciscoIetfIsisMIB 0 }
ciscoIetfIsisMIBObjects OBJECT IDENTIFIER ::= { ciscoIetfIsisMIB 1 }
ciscoIetfIsisMIBConform OBJECT IDENTIFIER ::= { ciscoIetfIsisMIB 2 }
-- OBJECT IDENTIFIER definitions
-- System wide attributes.
ciiSystem OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 1 }
-- Attributes associated with the domain or with the area.
ciiSysLevel OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 2 }
-- Attributes associated with one Circuit
ciiCirc OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 3 }
-- Attributes associated with area or domain relevant within a Circuit.
ciiCircLevelValues OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 4 }
-- System and circuit counters.
ciiCounters OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 5 }
-- Attributes associated with an adjacent Protocol Peer.
ciiISAdj OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 6 }
-- Attributes associated with a configured address.
ciiReachAddr OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 7 }
-- Attributes associated with IP routes learned by
-- configuration or through another protocol.
ciiIPReachAddr OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 8 }
-- The collection of Link State PDUs known to the Intermediate System
ciiLSPDataBase OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 9 }
-- Objects included in Notifications.
ciiNotification OBJECT IDENTIFIER ::= { ciscoIetfIsisMIBObjects 10 }
-- Type definitions
CiiOSINSAddress ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"OSI Network Service Address, e.g. NSAP, SNPA, or Network
Entity Title"
SYNTAX OCTET STRING (SIZE(0..20))
CiiSystemID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A system ID."
SYNTAX OCTET STRING (SIZE(6))
CiiLinkStatePDUID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A Link State PDU Identifier."
SYNTAX OCTET STRING (SIZE(0|8))
CiiAdminState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Type used in enabling and disabling a row.
Values match those in RFC 2863."
SYNTAX INTEGER
{
on(1),
off(2)
}
CiiLSPBuffSize ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Integer sub range for LSP size."
SYNTAX Integer32 (512..16000)
CiiLevelState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"States of the IS-IS protocol."
SYNTAX INTEGER
{
off (1),
on (2),
waiting (3),
overloaded(4)
}
CiiSupportedProtocol ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Types of network protocol supported by Integrated IS-IS.
The values for ISO8473 and IP are those registered for
these protocols in ISO TR9577."
SYNTAX INTEGER
{
iso8473(129),
ipV6(142),
ip(204)
}
CiiDefaultMetric ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Integer sub-range for default metric for single hop.
ISO 10589 provides for 4 types of metric. Only the
'default' metric is used in practice."
SYNTAX Integer32 (0..63)
CiiWideMetric ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Wide Metric for IS Neighbors. ISO 10589 provides a
6 bit metric. Traffic Engineering extensions provide
24 bit metrics."
SYNTAX Unsigned32 (0..16777215)
CiiFullMetric ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Full Metric for IP Routes. Traffic Engineering extensions
provide 32 bit metrics."
SYNTAX Unsigned32
CiiMetricType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Is this an Internal or External Metric?"
SYNTAX INTEGER
{
internal(1),
external(2)
}
CiiMetricStyle ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Do we use 1195 style Metrics or wide metrics."
SYNTAX INTEGER
{
narrow(1),
wide(2),
both(3)
}
CiiISLevel ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a level."
SYNTAX INTEGER
{
none(0),
area(1), -- L1
domain(2) -- L2
}
CiiPDUHeader ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A block to contain the header from a PDU."
SYNTAX OCTET STRING (SIZE(0..64))
CiiCircuitID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"ID for a circuit."
SYNTAX OCTET STRING (SIZE(0|7))
CiiISPriority ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Integer sub-range for IS-IS priority."
SYNTAX Integer32 (0..127)
CiiUnsigned16TC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An Unsigned32 further restricted to 16 Bits. Note that
the ASN.1 BER encoding may still require 24 Bits for
some values."
SYNTAX Unsigned32 (0..65535)
CiiUnsigned8TC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An Unsigned32 further restricted to 8 Bits. Note that
the ASN.1 BER encoding may still require 16 Bits for
some values."
SYNTAX Unsigned32 (0..255)
-- Behavior Definitions
-- ResettingTimer behavior definition
-- "This object specifies the interval between certain events in
-- the operation of the protocol state machine. If the value of
-- this object is set to a new value while the protocol state
-- machine is in operation, the implementation shall take the
-- necessary steps to ensure that for any time interval which
-- was in progress when the value of the corresponding object
-- was changed, the next expiration of that interval takes place
-- the specified time after the original start of that interval,
-- or immediately, whichever is later. The precision with which
-- this time shall be implemented shall be the same as that
-- associated with the basic operation of the timer object."
-- ReplaceOnlyWhileDisabled behavior definition
-- "This object may not be modified while the corresponding
-- table row's variable of type CiiAdminState is in state on."
-- ManualOrAutomatic behavior definition
-- "The access of this object is read-write if the row to which
-- it belongs is manual (i.e. is being or was created manually)
-- otherwise (i.e. was created automatically) it is read-only."
ciiSysObject OBJECT IDENTIFIER ::= { ciiSystem 1 }
ciiSysVersion OBJECT-TYPE
SYNTAX INTEGER
{
unknown(0),
one(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of the IS-IS protocol that
is implemented."
REFERENCE "{ISIS.aoi version (1)}"
DEFVAL { one }
::= { ciiSysObject 1 }
ciiSysType OBJECT-TYPE
SYNTAX INTEGER
{
level1IS (1),
level2IS (2),
level1L2IS (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"At which levels is the Intermediate System
running? This object follows the
replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi iSType (2)}"
DEFVAL { level1L2IS }
::= { ciiSysObject 2 }
ciiSysID OBJECT-TYPE
SYNTAX CiiSystemID
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The ID for this Intermediate System.
This value is appended to each of the
area addresses to form the Network Entity Titles.
The derivation of a value for this object is
implementation-specific. Some implementations may
automatically assign values and not permit an
SNMP write, while others may require the value
to be set manually."
REFERENCE "{ISIS.aoi systemId (119)}"
::= { ciiSysObject 3 }
ciiSysMaxPathSplits OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of paths with equal routing metric value
which it is permitted to split between. This object
follows the replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi maximumPathSplits (3)}"
DEFVAL { 2 }
::= { ciiSysObject 4 }
ciiSysMaxLSPGenInt OBJECT-TYPE
SYNTAX Integer32 (1..65235)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum interval, in seconds, between generated LSPs
by this Intermediate System. This object follows
the resettingTimer behavior. The value must be
greater than any value configured for
ciiSysLevelMinLSPGenInt, and should be at least 300
seconds less than ciiSysMaxAge."
REFERENCE "{ISIS.aoi maximumLSPGenerationInterval (6)}"
DEFVAL { 900 }
::= { ciiSysObject 5 }
ciiSysPollESHelloRate OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value, in seconds, to be used for the suggested ES
configuration timer in ISH PDUs when soliciting the ES
configuration."
REFERENCE "{ISIS.aoi pollESHelloRate (13)}"
DEFVAL { 50 }
::= { ciiSysObject 6 }
ciiSysWaitTime OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Number of seconds to delay in 'waiting' state before
entering 'on' state. This object follows the resettingTimer
behavior."
REFERENCE "{ISIS.aoi waitingTime (15)}"
DEFVAL { 60 }
::= { ciiSysObject 7 }
ciiSysAdminState OBJECT-TYPE
SYNTAX CiiAdminState
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative state of this Intermediate
System. Setting this object to the value 'on'
when its current value is 'off' enables
the Intermediate System."
DEFVAL { off }
::= { ciiSysObject 8 }
ciiSysL2toL1Leaking OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If true, allow the router to leak L2 routes into L1."
DEFVAL { false }
::= { ciiSysObject 9 }
ciiSysMaxAge OBJECT-TYPE
SYNTAX CiiUnsigned16TC (350..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Value to place in RemainingLifeTime field of
the LSPs we generate.
This should be at least 300 seconds greater than
ciiSysMaxLSPGenInt."
DEFVAL { 1200 }
::= { ciiSysObject 10 }
ciiSysReceiveLSPBufferSize OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1492..16000)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Size of the largest Buffer we are designed or
configured to store. This should be at least
as big as the maximum ciiSysLevelOrigLSPBuffSize
supported by the system.
If resources allow, we will store and flood LSPs
larger than ciiSysReceiveLSPBufferSize, as this
can help avoid problems in networks with different
values for ciiSysLevelOrigLSPBuffSize."
DEFVAL { 1492 }
::= { ciiSysObject 11 }
-- The Level 1 Manual Area Address Table
-- contains the set of area addresses manually configured
-- for this Intermediate System.
-- At least one row in which the value of ciiManAreaAddrExistState
-- is active must be present. The maximum number of rows
-- in this table for for which the object
-- ciiManAreaAddrExistState has the value active is 3.
-- An attempt to create more 3 rows of ciiManAreaAddrEntry
-- with state 'active' in one instance of the IS-IS protocol
-- should return inconsistentValue.
ciiManAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiManAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of manual area addresses configured on this
Intermediate System."
REFERENCE "{ISIS.aoi manualAreaAddresses (10)}"
::= { ciiSystem 2 }
ciiManAreaAddrEntry OBJECT-TYPE
SYNTAX CiiManAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one area address manually configured
on this system"
INDEX { ciiManAreaAddr }
::= { ciiManAreaAddrTable 1 }
CiiManAreaAddrEntry ::=
SEQUENCE {
ciiManAreaAddr
CiiOSINSAddress,
ciiManAreaAddrExistState
RowStatus
}
ciiManAreaAddr OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A manually configured area address for this system. This
object follows the index behavior.
Note: an index for the entry {1, {49.0001} active} in
this table would be the ordered pair
(1, (0x03 0x49 0x00 0x01)), as the length of an Octet
string is part of the OID."
::= { ciiManAreaAddrEntry 1 }
ciiManAreaAddrExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of the ciiManAreaAddrEntry. This object
follows the Row Status behavior. If the ciiSysAdminState
for this Intermediate System is 'on', and an
attempt is made to set this object to the value 'destroy'
or 'notInService' when this is the only
ciiManAreaAddrEntry in state 'active' for this
Intermediate System should return inconsistentValue."
::= { ciiManAreaAddrEntry 2 }
-- The Level 1 Area Address Table
-- The Level 1 Area Address Table contains the
-- union of the sets of relevant area addresses configured or
-- learned from Level 1 LSPs received by this Intermediate System.
ciiAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The union of the sets of area addresses reported in all
Level 1 LSPs with fragment number zero generated by this
Intermediate System, or received from other Intermediate
Systems which are reachable via Level 1 routing."
REFERENCE "{ISIS.aoi areaAddresses (18)}"
::= { ciiSystem 3 }
ciiAreaAddrEntry OBJECT-TYPE
SYNTAX CiiAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one area address reported in a
Level 1 LSP generated or received by this Intermediate
System."
INDEX { ciiAreaAddr }
::= { ciiAreaAddrTable 1 }
CiiAreaAddrEntry ::=
SEQUENCE {
ciiAreaAddr
CiiOSINSAddress
}
ciiAreaAddr OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An area address reported in a Level 1 LSP."
::= { ciiAreaAddrEntry 1 }
-- The System Protocol Supported Table
-- The System Protocol Supported Table contains the manually
-- configured set of protocols supported by this
-- Intermediate System.
ciiSysProtSuppTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiSysProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the manually configured set of
protocols supported by this Intermediate System."
::= { ciiSystem 4 }
ciiSysProtSuppEntry OBJECT-TYPE
SYNTAX CiiSysProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one protocol supported by
this Intermediate System."
INDEX { ciiSysProtSuppProtocol }
::= { ciiSysProtSuppTable 1 }
CiiSysProtSuppEntry ::=
SEQUENCE {
ciiSysProtSuppProtocol
CiiSupportedProtocol,
ciiSysProtSuppExistState
RowStatus
}
ciiSysProtSuppProtocol OBJECT-TYPE
SYNTAX CiiSupportedProtocol
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One supported protocol. This object follows the index
behavior."
::= { ciiSysProtSuppEntry 1 }
ciiSysProtSuppExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of the ciiSysProtSuppEntry. This object
follows the RowStatus behavior."
::= { ciiSysProtSuppEntry 2 }
-- The Summary Address Table
-- The Summary Address Table contains the set of summary
-- addresses manually configured for the Intermediate System.
--
-- This is used to control leaking L1 routes into L2.
ciiSummAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiSummAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of IP summary addresses to use in forming
summary TLVs originated by this Intermediate System.
An administrator may use a summary address to combine
and modify IP Reachability announcements. If the
Intermediate system can reach any subset of the summary
address, the summary address will be announced instead,
at the configured metric."
::= { ciiSystem 5 }
ciiSummAddrEntry OBJECT-TYPE
SYNTAX CiiSummAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP summary address."
INDEX { ciiSummAddressType,
ciiSummAddress,
ciiSummAddrPrefixLen }
::= { ciiSummAddrTable 1 }
CiiSummAddrEntry ::=
SEQUENCE {
ciiSummAddressType
InetAddressType,
ciiSummAddress
InetAddress,
ciiSummAddrPrefixLen
InetAddressPrefixLength,
ciiSummAddrExistState
RowStatus,
ciiSummAddrMetric
CiiDefaultMetric,
ciiSummAddrFullMetric
CiiFullMetric
}
ciiSummAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Type of IP address for this summary address.
This object follows the index behavior."
::= { ciiSummAddrEntry 1 }
ciiSummAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP Address value for this summary address.
This object follows the index behavior."
::= { ciiSummAddrEntry 2 }
ciiSummAddrPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Length of the IP NetMask for this summary address."
::= { ciiSummAddrEntry 3 }
ciiSummAddrExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this summary address. This object
follows the row status behavior."
::= { ciiSummAddrEntry 4 }
ciiSummAddrMetric OBJECT-TYPE
SYNTAX CiiDefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value to announce this summary
address with in LSPs generated by this system."
DEFVAL { 20 }
::= { ciiSummAddrEntry 5 }
ciiSummAddrFullMetric OBJECT-TYPE
SYNTAX CiiFullMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The wide metric value to announce this summary
address with in LSPs generated by this system."
DEFVAL { 20 }
::= { ciiSummAddrEntry 6 }
-- The Redistribution table defines addresses that should be
-- leaked from L2 to L1 if ciiSysL2toL1Leaking is enabled.
ciiRedistributeAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiRedistributeAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides criteria to decide if a route should
be leaked from L2 to L1 when Domain Wide Prefix leaking is
enabled.
Addresses that match the summary mask in the table will
be announced at L1 by routers when ciiSysL2toL1Leaking
is enabled. Routes that fall into the ranges specified
are announced as is, without being summarized. Routes
that do not match a summary mask are not announced."
::= { ciiSystem 6 }
ciiRedistributeAddrEntry OBJECT-TYPE
SYNTAX CiiRedistributeAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP summary address to
manage leaking L2 addresses into L1."
INDEX { ciiRedistributeAddrType,
ciiRedistributeAddrAddress,
ciiRedistributeAddrPrefixLen }
::= { ciiRedistributeAddrTable 1 }
CiiRedistributeAddrEntry ::=
SEQUENCE {
ciiRedistributeAddrType
InetAddressType,
ciiRedistributeAddrAddress
InetAddress,
ciiRedistributeAddrPrefixLen
InetAddressPrefixLength,
ciiRedistributeAddrExistState
RowStatus
}
ciiRedistributeAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Type of IP address for this summary address.
This object follows the index behavior."
::= { ciiRedistributeAddrEntry 1 }
ciiRedistributeAddrAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP Address value for this summary address.
This object follows the index behavior."
::= { ciiRedistributeAddrEntry 2 }
ciiRedistributeAddrPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Length of the IP NetMask for this summary address."
::= { ciiRedistributeAddrEntry 3 }
ciiRedistributeAddrExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this summary address. This object
follows the row status behavior."
::= { ciiRedistributeAddrEntry 4 }
-- The Router Table keeps track of hostnames and router IDs
-- associated with peers in the area and domain.
ciiRouterTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiRouterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of hostnames and router ID."
::= { ciiSystem 7 }
ciiRouterEntry OBJECT-TYPE
SYNTAX CiiRouterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry tracks information about one peer at
one level."
INDEX { ciiRouterSysID,
ciiRouterLevel }
::= { ciiRouterTable 1 }
CiiRouterEntry ::=
SEQUENCE {
ciiRouterSysID
CiiSystemID,
ciiRouterLevel
CiiISLevel,
ciiRouterHostName
SnmpAdminString,
ciiRouterID
Unsigned32
}
ciiRouterSysID OBJECT-TYPE
SYNTAX CiiSystemID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The System ID of the Router Peer."
::= { ciiRouterEntry 1 }
ciiRouterLevel OBJECT-TYPE
SYNTAX CiiISLevel
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level of this Intermediate System."
::= { ciiRouterEntry 2 }
ciiRouterHostName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The hostname listed in LSP, or zero-length string if none."
::= { ciiRouterEntry 3 }
ciiRouterID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Peer found in LSP, or zero if none."
::= { ciiRouterEntry 4 }
-- The System Level Table
-- This table captures level-specific information about the System
ciiSysLevelTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiSysLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Level specific information about the System."
::= { ciiSysLevel 1 }
ciiSysLevelEntry OBJECT-TYPE
SYNTAX CiiSysLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describe variables defined for Area or Domain."
INDEX { ciiSysLevelIndex }
::= { ciiSysLevelTable 1 }
CiiSysLevelEntry ::=
SEQUENCE {
ciiSysLevelIndex
INTEGER,
ciiSysLevelOrigLSPBuffSize
CiiLSPBuffSize,
ciiSysLevelMinLSPGenInt
CiiUnsigned16TC,
ciiSysLevelOverloadState
CiiLevelState,
ciiSysLevelSetOverload
TruthValue,
ciiSysLevelSetOverloadUntil
TimeTicks,
ciiSysLevelMetricStyle
CiiMetricStyle,
ciiSysLevelSPFConsiders
CiiMetricStyle,
ciiSysLevelTEEnabled
TruthValue
}
ciiSysLevelIndex OBJECT-TYPE
SYNTAX INTEGER
{
level1IS (1),
level2IS (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level that this entry describes."
::= { ciiSysLevelEntry 1 }
ciiSysLevelOrigLSPBuffSize OBJECT-TYPE
SYNTAX CiiLSPBuffSize
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum size of LSPs and SNPs originated by
this Intermediate System at this level.
This object follows the replaceOnlyWhileDisabled
behavior."
REFERENCE "{ISIS.aoi originatingL1LSPBufferSize (9)}"
DEFVAL { 1492 }
::= { ciiSysLevelEntry 2 }
ciiSysLevelMinLSPGenInt OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum interval, in seconds, between successive
generation of LSPs with the same LSPID at this level
by this Intermediate System. This object
follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi minimumLSPGenerationInterval (11)}"
DEFVAL { 30 }
::= { ciiSysLevelEntry 3 }
ciiSysLevelOverloadState OBJECT-TYPE
SYNTAX CiiLevelState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the database at this level.
The value 'off' indicates that IS-IS is not active at
this level.
The value 'on' indicates that IS-IS is active at this
level, and not overloaded.
The value 'waiting' indicates a database that is low on
an essential resource, such as memory.
The administrator may force the state to 'overloaded'
by setting the object ciiSysLevelSetOverload.
If the state is 'waiting' or 'overloaded', we originate
LSPs with the Overload bit set."
REFERENCE "{ISIS.aoi l1State (17)}"
::= { ciiSysLevelEntry 4 }
ciiSysLevelSetOverload OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively set the overload bit for the level.
The overload bit will continue to be set if the
implementation runs out of memory, independent of
this variable"
DEFVAL { false }
::= { ciiSysLevelEntry 5 }
ciiSysLevelSetOverloadUntil OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If set, the overload bit should be set, and cleared
after sysUpTime exceeds this value."
DEFVAL { 0 }
::= { ciiSysLevelEntry 6 }
ciiSysLevelMetricStyle OBJECT-TYPE
SYNTAX CiiMetricStyle
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Which style of Metric do we generate in our LSPs
at this level? This object follows the
replaceOnlyWhileDisabled behavior."
DEFVAL { narrow }
::= { ciiSysLevelEntry 7 }
ciiSysLevelSPFConsiders OBJECT-TYPE
SYNTAX CiiMetricStyle
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Which style of Metric do we consider in our
SPF computation at this level?"
DEFVAL { narrow }
::= { ciiSysLevelEntry 8 }
ciiSysLevelTEEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Do we do Traffic Engineering at this level?"
DEFVAL { false }
::= { ciiSysLevelEntry 9 }
-- Static to provide next CircIndex
ciiNextCircIndex OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to assign values to
ciiCircIndex as described in 'Textual
Conventions for SNMPv2'. The network manager
reads this object, and then writes the value
back as the ciiCircIndex in a SET that creates
a new instance of ciiCircEntry. If the SET
fails with the code 'inconsistentValue', then
the process must be repeated; If the SET succeeds,
then the object is incremented, and the new
ciiCircEntry is created according to the manager's
directions."
::= { ciiCirc 1 }
-- The Circuit Table
-- Each broadcast or point-to-point interface on the system
-- corresponds to one entry in the Circuit table. However, there
-- may be multiple X.25 DA circuit entries in the Circuit table
-- for a given X.25 interface.
ciiCircTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiCircEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of circuits used by this
Intermediate System."
::= { ciiCirc 2 }
ciiCircEntry OBJECT-TYPE
SYNTAX CiiCircEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An ciiCircEntry exists for each circuit used by
Integrated IS-IS on this system."
INDEX { ciiCircIndex }
::= { ciiCircTable 1 }
CiiCircEntry ::=
SEQUENCE {
ciiCircIndex
Integer32,
ciiCircIfIndex
InterfaceIndex,
ciiCircIfSubIndex
Integer32,
ciiCircAdminState
CiiAdminState,
ciiCircExistState
RowStatus,
ciiCircType
INTEGER,
ciiCircExtDomain
TruthValue,
ciiCircLevel
INTEGER,
ciiCircPassiveCircuit
TruthValue,
ciiCircMeshGroupEnabled
INTEGER,
ciiCircMeshGroup
Unsigned32,
ciiCircSmallHellos
TruthValue,
ciiCircLastUpTime
TimeTicks,
ciiCirc3WayEnabled
TruthValue,
ciiCircExtendedCircID
Unsigned32
}
ciiCircIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier of this circuit, unique within the
Intermediate System. This object follows
the index behavior. This is for SNMP Indexing
purposes only and need not have any relation to
any protocol value."
::= { ciiCircEntry 1 }
ciiCircIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of ifIndex for the interface to which this
circuit corresponds. This object cannot be modified
after creation"
::= { ciiCircEntry 2 }
ciiCircIfSubIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A specifier for the part of the interface ifIndex to which
this circuit corresponds, such as a DLCI or VPI/VCI.
This object cannot be modified after creation"
::= { ciiCircEntry 3 }
ciiCircAdminState OBJECT-TYPE
SYNTAX CiiAdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of the circuit. This
object follows the CiiAdminState behavior."
DEFVAL { off }
::= { ciiCircEntry 4 }
ciiCircExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this circuit. This object follows
the RowStatus behavior. Setting the state to
'notInService' halts the generation and processing of
IS-IS protocol PDUs on this circuit. Setting the state
to 'destroy' will also erase any configuration associated
with the circuit."
::= { ciiCircEntry 5 }
ciiCircType OBJECT-TYPE
SYNTAX INTEGER
{
broadcast(1),
ptToPt(2),
staticIn(3),
staticOut(4),
dA(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the circuit. This object follows the
replaceOnlyWhileDisabled behavior. The type specified
must be compatible with the type of the interface defined
by the value of ciiCircIfIndex."
REFERENCE "{ISIS.aoi type (33)}"
::= { ciiCircEntry 6 }
ciiCircExtDomain OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If true, suppress normal transmission of and
interpretation of Intra-domain IS-IS PDUs on this
circuit."
REFERENCE "{ISIS.aoi externalDomain (46)}"
DEFVAL { false }
::= { ciiCircEntry 7 }
ciiCircLevel OBJECT-TYPE
SYNTAX INTEGER
{
level1(1),
level2(2),
level1L2(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates which type of packets will be sent and
accepted on this circuit. The values used will be
modified by the settings of ciiSysType. This
object follows the replaceOnlyWhileDisabled behavior."
DEFVAL { level1L2 }
::= { ciiCircEntry 8 }
ciiCircPassiveCircuit OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Should we include this interface in LSPs, even if
it is not running the IS-IS Protocol?"
DEFVAL { false }
::= { ciiCircEntry 9 }
ciiCircMeshGroupEnabled OBJECT-TYPE
SYNTAX INTEGER
{
inactive(1),
blocked(2),
set(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Is this port a member of a mesh group, or blocked?
Circuits in the same mesh group act as a virtual
multiaccess network. LSPs seen on one circuit in
a mesh group will not be flooded to another circuit
in the same mesh group."
REFERENCE "{ RFC 2973 }"
DEFVAL { inactive }
::= { ciiCircEntry 10 }
ciiCircMeshGroup OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Circuits in the same mesh group act as a virtual
multiaccess network. LSPs seen on one circuit in
a mesh group will not be flooded to another circuit
in the same mesh group. If ciiCircMeshGroupEnabled
is inactive or blocked, this value is ignored."
REFERENCE "{ RFC 2973 }"
::= { ciiCircEntry 11 }
ciiCircSmallHellos OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Can we send unpadded hellos on LAN circuits? 'false'
means LAN Hellos must be padded.
Implementations should allow the administrator to read
this value. An implementation need not be able to
support unpadded hellos to be conformant."
DEFVAL { false }
::= { ciiCircEntry 12 }
ciiCircLastUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the circuit is enabled, the value of sysUpTime
when ciiCircAdminState most recently entered
the state 'on'. If the circuit is not 'on',
the value of sysUpTime when the circuit last
entered state 'on', 0 if the circuit has never
been 'on'."
::= { ciiCircEntry 13 }
ciiCirc3WayEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Is this circuit enabled to run 3Way handshake?"
DEFVAL { true }
::= { ciiCircEntry 14 }
ciiCircExtendedCircID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value to be used as the extended circuit ID in
3Way handshake. This value is only used if
ciiCirc3WayEnabled is true, and must be unique across
all circuits on this IS."
::= { ciiCircEntry 15 }
-- The Circuit Level Table
-- This table captures level-specific information about a circuit
ciiCircLevelTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiCircLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Level specific information about circuits used by IS-IS"
::= { ciiCircLevelValues 1 }
ciiCircLevelEntry OBJECT-TYPE
SYNTAX CiiCircLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An ciiCircLevelEntry exists for each level on
each circuit used by Integrated IS-IS on this system."
INDEX { ciiCircIndex,
ciiCircLevelIndex }
::= { ciiCircLevelTable 1 }
CiiCircLevelEntry ::=
SEQUENCE {
ciiCircLevelIndex
INTEGER,
ciiCircLevelMetric
CiiDefaultMetric,
ciiCircLevelWideMetric
CiiWideMetric,
ciiCircLevelISPriority
CiiISPriority,
ciiCircLevelIDOctet
Integer32,
ciiCircLevelID
CiiCircuitID,
ciiCircLevelDesIS
CiiCircuitID,
ciiCircLevelHelloMultiplier
Integer32,
ciiCircLevelHelloTimer
Integer32,
ciiCircLevelDRHelloTimer
Integer32,
ciiCircLevelLSPThrottle
CiiUnsigned16TC,
ciiCircLevelMinLSPRetransInt
Integer32,
ciiCircLevelCSNPInterval
Integer32,
ciiCircLevelPartSNPInterval
Integer32
}
ciiCircLevelIndex OBJECT-TYPE
SYNTAX INTEGER
{
level1IS (1),
level2IS (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level that this entry describes."
::= { ciiCircLevelEntry 1 }
ciiCircLevelMetric OBJECT-TYPE
SYNTAX CiiDefaultMetric
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The metric value of this circuit for this level."
REFERENCE "{ISIS.aoi l1DefaultMetric (35)}"
DEFVAL { 10 }
::= { ciiCircLevelEntry 2 }
ciiCircLevelWideMetric OBJECT-TYPE
SYNTAX CiiWideMetric
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The wide metric value of this circuit for this level."
DEFVAL { 10 }
::= { ciiCircLevelEntry 3 }
ciiCircLevelISPriority OBJECT-TYPE
SYNTAX CiiISPriority
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The priority for becoming LAN Designated
Intermediate System at this level."
REFERENCE "{ISIS.aoi l2IntermediateSystemPriority (73)}"
DEFVAL { 64 }
::= { ciiCircLevelEntry 4 }
ciiCircLevelIDOctet OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A one byte identifier that can be used in protocol packets
to identify a circuit. Values of ciiCircLevelIDOctet
do not need to be unique. They are only required to
differ on LANs where the Intermediate System is the
Designated Intermediate System."
::= { ciiCircLevelEntry 5 }
ciiCircLevelID OBJECT-TYPE
SYNTAX CiiCircuitID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"On a point to point circuit with a fully initialized
adjacency to a peer IS, the value of this object is
the circuit ID negotiated during adjacency initialization.
On a point to point circuit without such an adjacency,
the value is the concatenation of the local system ID
and the one byte ciiCircLevelIDOctet for this circuit
i.e. the value that would be proposed for the circuit ID.
On other circuit types, the value returned is the zero
length OCTET STRING."
REFERENCE "{ISIS.aoi ptPtCircuitID (51)}"
::= { ciiCircLevelEntry 6 }
ciiCircLevelDesIS OBJECT-TYPE
SYNTAX CiiCircuitID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ID of the LAN Designated Intermediate System
on this circuit at this level. If, for any reason,
this system is not partaking in the relevant
Designated Intermediate System election process,
then the value returned is the zero length OCTET STRING."
REFERENCE "{ISIS.aoi l2DesignatedIntermediateSystem (75)}"
::= { ciiCircLevelEntry 7 }
ciiCircLevelHelloMultiplier OBJECT-TYPE
SYNTAX Integer32 (2..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This value is multiplied by the corresponding HelloTimer
and the result in seconds (rounded up) is used as the
holding time in transmitted hellos, to be used by
receivers of hello packets from this IS"
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 10 }
::= { ciiCircLevelEntry 8 }
ciiCircLevelHelloTimer OBJECT-TYPE
SYNTAX Integer32 (10..600000)
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum period, in milliseconds, between IIH PDUs
on multiaccess networks at this level for LANs.
The value at L1 is used as the period between
Hellos on L1L2 point to point circuits. Setting
this value at level 2 on an L1L2 point to point
circuit will result in an error of InconsistentValue.
This object follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 3000 }
::= { ciiCircLevelEntry 9 }
ciiCircLevelDRHelloTimer OBJECT-TYPE
SYNTAX Integer32 (10..120000)
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Period, in milliseconds, between Hello PDUs on
multiaccess networks when this IS is the Designated
Intermediate System. This object follows the
resettingTimer behavior."
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 1000 }
::= { ciiCircLevelEntry 10 }
ciiCircLevelLSPThrottle OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1..65535)
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimal interval of time, in milliseconds, between
transmissions of LSPs on an interface at this level."
REFERENCE
"{ISIS.aoi minimumBroadcastLSPTransmissionInterval (5)}"
DEFVAL { 30 }
::= { ciiCircLevelEntry 11 }
ciiCircLevelMinLSPRetransInt OBJECT-TYPE
SYNTAX Integer32 (1..300)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum interval, in seconds, between re-transmission of
an LSP at this level. This object follows the
resettingTimer behavior.
Note that ciiCircLevelLSPThrottle controls
how fast we send back to back LSPs. This variable
controls how fast we re-send the same LSP."
REFERENCE "{ISIS.aoi minimumLSPTransmissionInterval (5)}"
DEFVAL { 5 }
::= { ciiCircLevelEntry 12 }
ciiCircLevelCSNPInterval OBJECT-TYPE
SYNTAX Integer32 (1..600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Interval of time, in seconds, between periodic
transmission of a complete set of CSNPs on
multiaccess networks if this router is the
designated router at this level.
This object follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi completeSNPInterval (8)}"
DEFVAL { 10 }
::= { ciiCircLevelEntry 13 }
ciiCircLevelPartSNPInterval OBJECT-TYPE
SYNTAX Integer32 (1..120)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum interval in seconds between sending Partial
Sequence Number PDUs at this level. This object
follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi partialSNPInterval (14)}"
DEFVAL { 2 }
::= { ciiCircLevelEntry 14 }
-- ciiSystemCounterTable keeps track of system-wide events.
ciiSystemCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiSystemCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"System wide counters for this Intermediate System."
::= { ciiCounters 1 }
ciiSystemCounterEntry OBJECT-TYPE
SYNTAX CiiSystemCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"System-wide IS-IS counters."
INDEX { ciiSysStatLevel }
::= { ciiSystemCounterTable 1 }
CiiSystemCounterEntry ::=
SEQUENCE {
ciiSysStatLevel
INTEGER,
ciiSysStatCorrLSPs
Counter32,
ciiSysStatAuthTypeFails
Counter32,
ciiSysStatAuthFails
Counter32,
ciiSysStatLSPDbaseOloads
Counter32,
ciiSysStatManAddrDropFromAreas
Counter32,
ciiSysStatAttmptToExMaxSeqNums
Counter32,
ciiSysStatSeqNumSkips
Counter32,
ciiSysStatOwnLSPPurges
Counter32,
ciiSysStatIDFieldLenMismatches
Counter32,
ciiSysStatPartChanges
Counter32,
ciiSysStatSPFRuns
Counter32,
ciiSysStatLSPErrors
Counter32
}
ciiSysStatLevel OBJECT-TYPE
SYNTAX INTEGER
{
level1IS (1),
level2IS (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level that this entry describes."
::= { ciiSystemCounterEntry 1 }
ciiSysStatCorrLSPs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of corrupted in-memory LSP frames detected.
LSPs received from the wire with a bad checksum
are silently dropped and not counted.
LSPs received from the wire with parse errors
are counted by ciiSysStatLSPErrors."
REFERENCE "{ISIS.aoi corruptedLSPsDetected (19)}"
::= { ciiSystemCounterEntry 2 }
ciiSysStatAuthTypeFails OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames with authentication type mismatches
recognized by this Intermediate System."
::= { ciiSystemCounterEntry 3 }
ciiSysStatAuthFails OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames with authentication failures
recognized by this Intermediate System."
::= { ciiSystemCounterEntry 4 }
ciiSysStatLSPDbaseOloads OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the LSP database has become
overloaded."
REFERENCE "{ISIS.aoi lSPL1DatabaseOverloads (20)}"
::= { ciiSystemCounterEntry 5 }
ciiSysStatManAddrDropFromAreas OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a manual address has been dropped from
the area."
REFERENCE "{ISIS.aoi manualAddressesDroppedFromArea (21)}"
::= { ciiSystemCounterEntry 6 }
ciiSysStatAttmptToExMaxSeqNums OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the IS has attempted to exceed the
maximum sequence number."
REFERENCE
"{ISIS.aoi attemptsToExceedmaximumSequenceNumber (22)}"
::= { ciiSystemCounterEntry 7 }
ciiSysStatSeqNumSkips OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a sequence number skip has occurred."
REFERENCE "{ISIS.aoi sequenceNumberSkips (23)}"
::= { ciiSystemCounterEntry 8 }
ciiSysStatOwnLSPPurges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a zero-aged copy of the system's own LSP
is received from some other node."
REFERENCE "{ISIS.aoi ownLSPPurges (24)}"
::= { ciiSystemCounterEntry 9 }
ciiSysStatIDFieldLenMismatches OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a PDU is received with a different value
for ID field length to that of the receiving system."
REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}"
::= { ciiSystemCounterEntry 10 }
ciiSysStatPartChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Partition changes"
::= { ciiSystemCounterEntry 11 }
ciiSysStatSPFRuns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times we ran SPF at this level."
::= { ciiSystemCounterEntry 12 }
ciiSysStatLSPErrors OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of LSP frames with errors we have received."
::= { ciiSystemCounterEntry 13 }
-- ciiCircuitCounterTable keeps track of events
-- specific to a circuit and a level
ciiCircuitCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiCircuitCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Circuit specific counters for this
Intermediate System."
::= { ciiCounters 2 }
ciiCircuitCounterEntry OBJECT-TYPE
SYNTAX CiiCircuitCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An ciiCircuitCounterEntry exists for each circuit
used by Integrated IS-IS on this system."
INDEX { ciiCircIndex,
ciiCircuitType }
::= { ciiCircuitCounterTable 1 }
CiiCircuitCounterEntry ::= SEQUENCE {
ciiCircuitType
INTEGER,
ciiCircAdjChanges
Counter32,
ciiCircNumAdj
Unsigned32,
ciiCircInitFails
Counter32,
ciiCircRejAdjs
Counter32,
ciiCircIDFieldLenMismatches
Counter32,
ciiCircMaxAreaAddrMismatches
Counter32,
ciiCircAuthTypeFails
Counter32,
ciiCircAuthFails
Counter32,
ciiCircLANDesISChanges
Counter32
}
ciiCircuitType OBJECT-TYPE
SYNTAX INTEGER
{
lanlevel1(1),
lanlevel2(2),
p2pcircuit(3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"What type of circuit saw these counts?
The point to point Hello PDU includes
both L1 and L2, and ISs form a single
adjacency on point to point links.
Thus we combine counts on
point to point links into one group."
::= { ciiCircuitCounterEntry 1 }
ciiCircAdjChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an adjacency state change has
occurred on this circuit."
REFERENCE "{ISIS.aoi changesInAdjacencyState (40)}"
::= { ciiCircuitCounterEntry 2 }
ciiCircNumAdj OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of adjacencies on this circuit."
REFERENCE "{ISIS.aoi changesInAdjacencyState (40)}"
::= { ciiCircuitCounterEntry 3 }
ciiCircInitFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times initialization of this circuit has
failed. This counts events such as PPP NCP failures.
Failures to form an adjacency are counted by
ciiCircRejAdjs."
::= { ciiCircuitCounterEntry 4 }
ciiCircRejAdjs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an adjacency has been rejected on
this circuit."
REFERENCE "{ISIS.aoi rejectedAdjacencies (42)}"
::= { ciiCircuitCounterEntry 5 }
ciiCircIDFieldLenMismatches OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an IS-IS control PDU with an ID
field length different to that for this system has been
received."
REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}"
::= { ciiCircuitCounterEntry 6 }
ciiCircMaxAreaAddrMismatches OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an IS-IS control PDU with a
max area address field different to that for this
system has been received."
REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}"
::= { ciiCircuitCounterEntry 7 }
ciiCircAuthTypeFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an IS-IS control PDU with
an auth type field different to that for this
system has been received."
::= { ciiCircuitCounterEntry 8 }
ciiCircAuthFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an IS-IS control PDU with
the correct auth type has failed to pass authentication
validation."
::= { ciiCircuitCounterEntry 9 }
ciiCircLANDesISChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Designated IS has changed
on this circuit at this level. If the circuit is
point to point, this count is zero."
::= { ciiCircuitCounterEntry 10 }
-- ciiPacketCounterTable keeps track of the number of IS-IS
-- control packets sent and received at each level
ciiPacketCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiPacketCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about IS-IS protocol traffic at one level
on one circuit in one direction"
::= { ciiCounters 3 }
ciiPacketCounterEntry OBJECT-TYPE
SYNTAX CiiPacketCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about IS-IS protocol traffic at one level
on one circuit in one direction"
INDEX { ciiCircIndex,
ciiPacketCountLevel,
ciiPacketCountDirection }
::= { ciiPacketCounterTable 1 }
CiiPacketCounterEntry ::=
SEQUENCE {
ciiPacketCountLevel
INTEGER,
ciiPacketCountDirection
INTEGER,
ciiPacketCountIIHellos
Counter32,
ciiPacketCountISHellos
Counter32,
ciiPacketCountESHellos
Counter32,
ciiPacketCountLSPs
Counter32,
ciiPacketCountCSNPs
Counter32,
ciiPacketCountPSNPs
Counter32,
ciiPacketCountUnknowns
Counter32
}
ciiPacketCountLevel OBJECT-TYPE
SYNTAX INTEGER
{
level1(1),
level2(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level at which these PDU counts have been collected."
::= { ciiPacketCounterEntry 1 }
ciiPacketCountDirection OBJECT-TYPE
SYNTAX INTEGER
{
sending(1),
receiving(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Were we sending or receiving these PDUs?"
::= { ciiPacketCounterEntry 2 }
ciiPacketCountIIHellos OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS Hello PDU frames seen in this
direction at this level.
Point-to-Point IIH PDUs are counted at
the lowest enabled level: at L1 on L1 or L1L2 circuits,
and at L2 otherwise."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { ciiPacketCounterEntry 3 }
ciiPacketCountISHellos OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of ES-IS Hello PDU frames seen in this
direction. ISH PDUs are counted at the
lowest enabled level: at L1 on L1 or L1L2
circuits, and at L2 otherwise."
::= { ciiPacketCounterEntry 4 }
ciiPacketCountESHellos OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of ES Hello PDU frames seen in this
direction. ESH PDUs are counted at the
lowest enabled level: at L1 on L1 or L1L2
circuits, and at L2 otherwise."
::= { ciiPacketCounterEntry 5 }
ciiPacketCountLSPs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS LSP frames seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { ciiPacketCounterEntry 6 }
ciiPacketCountCSNPs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS CSNP frames seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { ciiPacketCounterEntry 7 }
ciiPacketCountPSNPs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS PSNP frames seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { ciiPacketCounterEntry 8 }
ciiPacketCountUnknowns OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unknown IS-IS PDU frames seen
at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { ciiPacketCounterEntry 9 }
-- The IS Adjacency Table
--
-- Each adjacency to an IS corresponds to one entry in this
-- table.
ciiISAdjTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiISAdjEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of adjacencies to Intermediate Systems."
::= { ciiISAdj 1 }
ciiISAdjEntry OBJECT-TYPE
SYNTAX CiiISAdjEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to one adjacency to an
Intermediate System on this system."
INDEX { ciiCircIndex,
ciiISAdjIndex }
::= { ciiISAdjTable 1 }
CiiISAdjEntry ::=
SEQUENCE {
ciiISAdjIndex
Integer32,
ciiISAdjState
INTEGER,
ciiISAdj3WayState
INTEGER,
ciiISAdjNeighSNPAAddress
CiiOSINSAddress,
ciiISAdjNeighSysType
INTEGER,
ciiISAdjNeighSysID
CiiSystemID,
ciiISAdjNbrExtendedCircID
Unsigned32,
ciiISAdjUsage
INTEGER,
ciiISAdjHoldTimer
CiiUnsigned16TC,
ciiISAdjNeighPriority
CiiISPriority,
ciiISAdjLastUpTime
TimeTicks
}
ciiISAdjIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value identifying the IS adjacency from all
other such adjacencies on this circuit. This value is
automatically assigned by the system when the adjacency
is created."
::= { ciiISAdjEntry 1 }
ciiISAdjState OBJECT-TYPE
SYNTAX INTEGER
{
down (1),
initializing (2),
up (3),
failed(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the adjacency"
REFERENCE "{ISIS.aoi adjacencyState (78)}"
::= { ciiISAdjEntry 2 }
ciiISAdj3WayState OBJECT-TYPE
SYNTAX INTEGER
{
up (0),
initializing (1),
down (2),
failed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 3Way state of the adjacency. These are picked
to match the historical on-the-wire representation
of the 3Way state, and are not intended to match
ciiISAdjState."
REFERENCE "{ RFC 3373 }"
::= { ciiISAdjEntry 3 }
ciiISAdjNeighSNPAAddress OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNPA address of the neighboring system."
REFERENCE "{ISIS.aoi neighbourSNPAAddress (79)}"
::= { ciiISAdjEntry 4 }
ciiISAdjNeighSysType OBJECT-TYPE
SYNTAX INTEGER
{
l1IntermediateSystem(1),
l2IntermediateSystem(2),
l1L2IntermediateSystem(3),
unknown(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the neighboring system."
REFERENCE "{ISIS.aoi neighbourSystemType (80)}"
::= { ciiISAdjEntry 5 }
ciiISAdjNeighSysID OBJECT-TYPE
SYNTAX CiiSystemID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The system ID of the neighboring Intermediate
System."
REFERENCE "{ISIS.aoi neighbourSystemIds (83)}"
::= { ciiISAdjEntry 6 }
ciiISAdjNbrExtendedCircID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 4 byte Extended Circuit ID learned from the
Neighbor during 3-way handshake, or 0."
::= { ciiISAdjEntry 7 }
ciiISAdjUsage OBJECT-TYPE
SYNTAX INTEGER
{
level1(1),
level2(2),
level1and2(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"How is the adjacency used? On a point-to-point link,
this might be level1and2, but on a LAN, the usage will
be level1 on the adjacency between peers at L1,
and level2 for the adjacency between peers at L2."
REFERENCE "{ISIS.aoi adjacencyUsage (82)}"
::= { ciiISAdjEntry 8 }
ciiISAdjHoldTimer OBJECT-TYPE
SYNTAX CiiUnsigned16TC (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The holding time in seconds for this adjacency.
This value is based on received IIH PDUs and
the elapsed time since receipt."
REFERENCE "{ISIS.aoi holdingTimer (85)}"
::= { ciiISAdjEntry 9 }
ciiISAdjNeighPriority OBJECT-TYPE
SYNTAX CiiISPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Priority of the neighboring Intermediate System for
becoming the Designated Intermediate System."
REFERENCE "{ISIS.aoi lANPriority (86)}"
::= { ciiISAdjEntry 10 }
ciiISAdjLastUpTime OBJECT-TYPE
SYNTAX TimeTicks
UNITS "hundredths of a second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the ciiISAdjState is in state 'up', the value
of sysUpTime when the adjacency most recently
entered the state 'up', or 0 if it has never
been in state 'up'."
::= { ciiISAdjEntry 11 }
-- The IS Adjacency Area Address Table
-- The IS Adjacency Area Address Table contains the set of
-- Area Addresses of neighboring
-- Intermediate Systems as reported in IIH PDUs.
ciiISAdjAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiISAdjAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of Area Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs."
REFERENCE "{ISIS.aoi areaAddressesOfNeighbour (84)}"
::= { ciiISAdj 2 }
ciiISAdjAreaAddrEntry OBJECT-TYPE
SYNTAX CiiISAdjAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one Area Address reported by a
neighboring Intermediate System in its IIH PDUs."
INDEX { ciiCircIndex,
ciiISAdjIndex,
ciiISAdjAreaAddrIndex }
::= { ciiISAdjAreaAddrTable 1 }
CiiISAdjAreaAddrEntry ::=
SEQUENCE {
ciiISAdjAreaAddrIndex
Integer32,
ciiISAdjAreaAddress
CiiOSINSAddress
}
ciiISAdjAreaAddrIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index for the areas associated with one neighbor.
This provides a simple way to walk the table."
::= { ciiISAdjAreaAddrEntry 1 }
ciiISAdjAreaAddress OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One Area Address as reported in IIH PDUs received from
the neighbor."
::= { ciiISAdjAreaAddrEntry 2 }
-- The IS Adjacency IP Address Table
-- The IS Adjacency IP Address Table contains the
-- set of IP Addresses of neighboring Intermediate Systems
-- as reported in received IIH PDUs.
ciiISAdjIPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiISAdjIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of IP Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs."
::= { ciiISAdj 3 }
ciiISAdjIPAddrEntry OBJECT-TYPE
SYNTAX CiiISAdjIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP Address reported by a
neighboring Intermediate System in its IIH PDUs."
INDEX { ciiCircIndex,
ciiISAdjIndex,
ciiISAdjIPAddrIndex
}
::= { ciiISAdjIPAddrTable 1 }
CiiISAdjIPAddrEntry ::=
SEQUENCE {
ciiISAdjIPAddrIndex
Integer32,
ciiISAdjIPAddrType
InetAddressType,
ciiISAdjIPAddrAddress
InetAddress
}
ciiISAdjIPAddrIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index to this table which identifies the IP addresses
to which this entry belongs."
::= { ciiISAdjIPAddrEntry 1 }
ciiISAdjIPAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of one IP Address as reported in IIH PDUs
received from the neighbor."
::= { ciiISAdjIPAddrEntry 2 }
ciiISAdjIPAddrAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One IP Address as reported in IIH PDUs received from the
neighbor."
::= { ciiISAdjIPAddrEntry 3 }
-- The IS Adjacency Protocol Supported Table
--
-- The IS Adjacency Protocol Supported Table contains the set of
-- protocols supported by neighboring
-- Intermediate Systems as reported in received IIH PDUs.
ciiISAdjProtSuppTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiISAdjProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of protocols supported by
neighboring Intermediate Systems as reported in received
IIH PDUs."
::= { ciiISAdj 4 }
ciiISAdjProtSuppEntry OBJECT-TYPE
SYNTAX CiiISAdjProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one protocol supported by a
neighboring Intermediate System as reported in its IIH
PDUs."
INDEX { ciiCircIndex,
ciiISAdjIndex,
ciiISAdjProtSuppProtocol }
::= { ciiISAdjProtSuppTable 1 }
CiiISAdjProtSuppEntry ::=
SEQUENCE {
ciiISAdjProtSuppProtocol
CiiSupportedProtocol
}
ciiISAdjProtSuppProtocol OBJECT-TYPE
SYNTAX CiiSupportedProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One supported protocol as reported in IIH PDUs received
from the neighbor."
::= { ciiISAdjProtSuppEntry 1 }
-- The Reachable Address Group
--
-- The Reachable Address Group is optional.
-- The Reachable Address Table
-- Each entry records information about a reachable address
-- (NSAP or address prefix) manually configured on the system
-- or learned through another protocol.
ciiRATable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of Reachable Addresses to NSAPs or Address
Prefixes."
::= { ciiReachAddr 1 }
ciiRAEntry OBJECT-TYPE
SYNTAX CiiRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry defines a Reachable Address to a NSAP or
Address Prefix."
INDEX { ciiCircIndex,
ciiRAIndex }
::= { ciiRATable 1 }
CiiRAEntry ::=
SEQUENCE {
ciiRAIndex
Integer32,
ciiRAExistState
RowStatus,
ciiRAAdminState
CiiAdminState,
ciiRAAddrPrefix
CiiOSINSAddress,
ciiRAMapType
INTEGER,
ciiRAMetric
CiiDefaultMetric,
ciiRAMetricType
CiiMetricType,
ciiRASNPAAddress
CiiOSINSAddress,
ciiRASNPAMask
CiiOSINSAddress,
ciiRASNPAPrefix
CiiOSINSAddress,
ciiRAType
INTEGER
}
ciiRAIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier for this ciiRAEntry. This value must be
unique amongst all Reachable Addresses on the same parent
Circuit. This object follows the index and ManualOrAutomatic
behaviors."
::= { ciiRAEntry 1 }
ciiRAExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this Reachable Address. This
object follows the ManualOrAutomatic behaviors."
::= { ciiRAEntry 2 }
ciiRAAdminState OBJECT-TYPE
SYNTAX CiiAdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of the Reachable Address. This
object follows the CiiAdminState and ManualOrAutomatic
behaviors."
DEFVAL { off }
::= { ciiRAEntry 3 }
ciiRAAddrPrefix OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination of this Reachable Address. This is an
Address Prefix. This object follows the
replaceOnlyWhileDisabled and ManualOrAutomatic
behaviors."
REFERENCE "{ISIS.aoi addressPrefix (98)}"
::= { ciiRAEntry 4 }
ciiRAMapType OBJECT-TYPE
SYNTAX INTEGER
{
none (1),
explicit (2),
extractIDI (3),
extractDSP (4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of mapping to be employed to ascertain the SNPA
Address which should be used in forwarding PDUs for this
Reachable Address prefix. This object follows the
ManualOrAutomatic behavior. The following values of
mapping type are defined:
none: The mapping is null because the neighbor SNPA is
implicit by nature of the subnetwork (e.g. a
point-to-point linkage).
explicit: The subnetwork addresses in the object
ciiRASNPAAddress is to be used.
extractIDI: The SNPA is embedded in the IDI of
the destination NSAP Address. The mapping
algorithm extracts the SNPA to be used
according to the format and encoding rules of
ISO8473/Add2. This SNPA extraction algorithm can
be used in conjunction with Reachable Address
prefixes from the X.121, F.69, E.163 and E.164
addressing subdomains.
extractDSP: All, or a suffix, of the SNPA is embedded
in the DSP of the destination address. This SNPA
extraction algorithm extracts the embedded
subnetwork addressing information by performing a
logical AND of the ciiRASNPAMask object value
with the destination address. The part of the
SNPA extracted from the destination NSAP is
appended to the ciiRASNPAPrefix object value to
form the next hop subnetwork addressing
information."
REFERENCE "{ISO10589-ISIS.aoi mappingType (107)}"
::= { ciiRAEntry 5 }
ciiRAMetric OBJECT-TYPE
SYNTAX CiiDefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value for reaching the specified
prefix over this circuit. This object follows the
ManualOrAutomatic behavior."
REFERENCE "{ISIS.aoi DefaultMetric (99)}"
DEFVAL { 20 }
::= { ciiRAEntry 6 }
ciiRAMetricType OBJECT-TYPE
SYNTAX CiiMetricType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the metric is internal or
external. This object follows the ManualOrAutomatic
behavior."
REFERENCE "{ISIS.aoi DefaultMetricType (103)}"
DEFVAL { internal }
::= { ciiRAEntry 7 }
ciiRASNPAAddress OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SNPA Address to which a PDU may be forwarded in
order to reach a destination which matches the address
prefix of the Reachable Address. This object follows the
ManualOrAutomatic behavior."
REFERENCE "{ISIS.aoi sNPAAddresses (109)}"
-- note only one address may be specified per Reachable Address
-- in the MIB
DEFVAL { ''H }
::= { ciiRAEntry 8 }
ciiRASNPAMask OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A bit mask with 1 bits indicating the positions in the
effective destination address from which embedded SNPA
information is to be extracted. For the extraction the
first octet of the ciiRASNPAMask object value is aligned
with the first octet (AFI) of the NSAP Address. If the
ciiRASNPAMask object value and NSAP Address are of
different lengths, the shorter of the two is logically
padded with zeros before performing the extraction. This
object follows the ManualOrAutomatic behavior."
REFERENCE "{ISIS.aoi sNPAMask (122)}"
DEFVAL { '00'H }
::= { ciiRAEntry 9 }
ciiRASNPAPrefix OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A fixed SNPA prefix for use when the ciiRAMapType is
extractDSP. The SNPA Address to use is formed by
concatenating the fixed SNPA prefix with a variable SNPA
part that is extracted from the effective destination
address. For Reachable Address prefixes in which the
entire SNPA is embedded in the DSP the SNPA Prefix shall
be null. This object follows the ManualOrAutomatic
behavior."
REFERENCE "{ISIS.aoi sNPAPrefix (123)}"
DEFVAL { '00'H }
::= { ciiRAEntry 10 }
ciiRAType OBJECT-TYPE
SYNTAX INTEGER
{
manual (1),
automatic (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Reachable address. Those of type
manual are created by the network manager. Those
of type automatic are created through propagation
of routing information from another routing
protocol (eg. IDRP). "
DEFVAL {manual}
::= {ciiRAEntry 11 }
-- The IP Reachable Address Table
-- Each entry records information about one IP reachable
-- address manually configured on this system or learned from
-- another protocol.
ciiIPRATable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiIPRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of IP Reachable Addresses to networks,
subnetworks or hosts either manually configured or
learned from another protocol."
::= { ciiIPReachAddr 1 }
ciiIPRAEntry OBJECT-TYPE
SYNTAX CiiIPRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry defines an IP Reachable Address to a network,
subnetwork or host.
Each IP Reachable Address may have multiple entries in the
table, one for each equal cost path to the reachable address."
INDEX { ciiIPRADestType,
ciiIPRADest,
ciiIPRADestPrefixLen,
ciiIPRANextHopIndex }
::= { ciiIPRATable 1 }
CiiIPRAEntry ::=
SEQUENCE {
ciiIPRADestType
InetAddressType,
ciiIPRADest
InetAddress,
ciiIPRADestPrefixLen
InetAddressPrefixLength,
ciiIPRANextHopIndex
Integer32,
ciiIPRANextHopType
InetAddressType,
ciiIPRANextHop
InetAddress,
ciiIPRAType
INTEGER,
ciiIPRAExistState
RowStatus,
ciiIPRAAdminState
CiiAdminState,
ciiIPRAMetric
CiiDefaultMetric,
ciiIPRAMetricType
CiiMetricType,
ciiIPRAFullMetric
CiiFullMetric,
ciiIPRASNPAAddress
CiiOSINSAddress,
ciiIPRASourceType
INTEGER
}
ciiIPRADestType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of this IP Reachable Address. This object
follows the ManualOrAutomatic behavior."
::= { ciiIPRAEntry 1 }
ciiIPRADest OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination of this IP Reachable Address. This is
either a network address, subnetwork address or host
address. This object follows the ManualOrAutomatic
behavior."
::= { ciiIPRAEntry 2 }
ciiIPRADestPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length of the IP Netmask for Reachability Address.
This object follows the ManualOrAutomatic behavior."
::= { ciiIPRAEntry 3 }
ciiIPRANextHopIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of next hop. Used when there are multiple Equal
Cost Multipath alternatives for the same destination."
::= { ciiIPRAEntry 4 }
ciiIPRANextHopType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the IP next hop address."
::= { ciiIPRAEntry 5 }
ciiIPRANextHop OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The IP next hop to this destination."
::= { ciiIPRAEntry 6 }
ciiIPRAType OBJECT-TYPE
SYNTAX INTEGER
{
manual (1),
automatic (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of this IP Reachable Address. Those of type
manual are created by the network manager. Those of type
automatic are created through propagation of routing
information from another routing protocol. This object
follows the ManualOrAutomatic behavior."
::= { ciiIPRAEntry 7 }
ciiIPRAExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of this IP Reachable Address. This object
follows the ExistenceState and ManualOrAutomatic
behaviors."
::= { ciiIPRAEntry 8 }
ciiIPRAAdminState OBJECT-TYPE
SYNTAX CiiAdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of the IP Reachable Address. This
object follows the CiiAdminState and ManualOrAutomatic
behaviors."
DEFVAL { off }
::= { ciiIPRAEntry 9 }
ciiIPRAMetric OBJECT-TYPE
SYNTAX CiiDefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value for reaching the specified
destination over this circuit. This object follows the
ManualOrAutomatic behavior."
DEFVAL { 10 }
::= { ciiIPRAEntry 10 }
ciiIPRAMetricType OBJECT-TYPE
SYNTAX CiiMetricType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the metric is internal or
external. This object follows the ManualOrAutomatic
behavior."
DEFVAL { internal }
::= { ciiIPRAEntry 11 }
ciiIPRAFullMetric OBJECT-TYPE
SYNTAX CiiFullMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The wide metric value for reaching the specified
destination over this circuit. This object follows the
ManualOrAutomatic behavior."
DEFVAL { 10 }
::= { ciiIPRAEntry 12 }
ciiIPRASNPAAddress OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SNPA Address to which a PDU may be forwarded in
order to reach a destination which matches this IP
Reachable Address. This object follows the
ManualOrAutomatic behavior."
DEFVAL { ''H }
::= { ciiIPRAEntry 13 }
ciiIPRASourceType OBJECT-TYPE
SYNTAX INTEGER
{
static (1),
direct (2),
ospfv2 (3),
ospfv3 (4),
isis (5),
rip (6),
igrp (7),
eigrp (8),
bgp (9),
other (10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The origin of this route."
::= { ciiIPRAEntry 14 }
-- The LSP Database Table
--
-- The first table provides Summary Information about LSPs
-- The next table provides a complete record
ciiLSPSummaryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiLSPSummaryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of LSP Headers."
::= { ciiLSPDataBase 1 }
ciiLSPSummaryEntry OBJECT-TYPE
SYNTAX CiiLSPSummaryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry provides a summary describing an
LSP currently stored in the system."
INDEX { ciiLSPLevel,
ciiLSPID }
::= { ciiLSPSummaryTable 1 }
CiiLSPSummaryEntry ::=
SEQUENCE {
ciiLSPLevel
CiiISLevel,
ciiLSPID
CiiLinkStatePDUID,
ciiLSPSeq
Unsigned32,
ciiLSPZeroLife
TruthValue,
ciiLSPChecksum
CiiUnsigned16TC,
ciiLSPLifetimeRemain
CiiUnsigned16TC,
ciiLSPPDULength
CiiUnsigned16TC,
ciiLSPAttributes
CiiUnsigned8TC
}
ciiLSPLevel OBJECT-TYPE
SYNTAX CiiISLevel
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"At which level does this LSP appear?"
::= { ciiLSPSummaryEntry 1 }
ciiLSPID OBJECT-TYPE
SYNTAX CiiLinkStatePDUID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 8 byte LSP ID, consisting of the SystemID,
Circuit ID, and Fragment Number."
::= { ciiLSPSummaryEntry 2 }
ciiLSPSeq OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number for this LSP."
::= { ciiLSPSummaryEntry 3 }
ciiLSPZeroLife OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Is this LSP being purged by this System?"
::= { ciiLSPSummaryEntry 4 }
ciiLSPChecksum OBJECT-TYPE
SYNTAX CiiUnsigned16TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 16 bit Fletcher Checksum."
::= { ciiLSPSummaryEntry 5 }
ciiLSPLifetimeRemain OBJECT-TYPE
SYNTAX CiiUnsigned16TC
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remaining lifetime in seconds for this LSP."
::= { ciiLSPSummaryEntry 6 }
ciiLSPPDULength OBJECT-TYPE
SYNTAX CiiUnsigned16TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of this LSP."
::= { ciiLSPSummaryEntry 7 }
ciiLSPAttributes OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flags carried by the LSP."
::= { ciiLSPSummaryEntry 8 }
-- LSP Table
--
-- The full LSP as a sequence of {Type, Len, Value} tuples
-- Since the underlying LSP may have changed while downloading
-- TLVs, we provide the Sequence number and Checksum for each
-- LSP TLV, so the network manager may verify that they are
-- still working on the same version of the LSP.
ciiLSPTLVTable OBJECT-TYPE
SYNTAX SEQUENCE OF CiiLSPTLVEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The contents of each LSP."
::= { ciiLSPDataBase 2 }
ciiLSPTLVEntry OBJECT-TYPE
SYNTAX CiiLSPTLVEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes an LSP current stored in the
system."
INDEX { ciiLSPLevel,
ciiLSPID,
ciiLSPTLVIndex }
::= { ciiLSPTLVTable 1 }
CiiLSPTLVEntry ::=
SEQUENCE {
ciiLSPTLVIndex
Unsigned32,
ciiLSPTLVSeq
Unsigned32,
ciiLSPTLVChecksum
CiiUnsigned16TC,
ciiLSPTLVType
CiiUnsigned8TC,
ciiLSPTLVLen
CiiUnsigned8TC,
ciiLSPTLVValue
OCTET STRING
}
ciiLSPTLVIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this TLV in the LSP. The first TLV has index 1
and the Nth TLV has an index of N."
::= { ciiLSPTLVEntry 1 }
ciiLSPTLVSeq OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number for this LSP."
::= { ciiLSPTLVEntry 2 }
ciiLSPTLVChecksum OBJECT-TYPE
SYNTAX CiiUnsigned16TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 16 bit Fletcher Checksum."
::= { ciiLSPTLVEntry 3 }
ciiLSPTLVType OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of this TLV."
::= { ciiLSPTLVEntry 4 }
ciiLSPTLVLen OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of this TLV."
::= { ciiLSPTLVEntry 5 }
ciiLSPTLVValue OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this TLV."
::= { ciiLSPTLVEntry 6 }
-- The IS-IS Notification Table
-- The IS-IS Notification Table records fields that are
-- required for notifications
ciiNotificationEntry OBJECT IDENTIFIER
::= { ciiNotification 1 }
ciiPduLspId OBJECT-TYPE
SYNTAX CiiLinkStatePDUID
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"An Octet String that uniquely identifies
a Link State PDU."
::= { ciiNotificationEntry 1 }
ciiPduFragment OBJECT-TYPE
SYNTAX CiiPDUHeader
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds up to 64 initial bytes of a PDU that
triggered the notification."
::= { ciiNotificationEntry 2 }
ciiPduFieldLen OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds the System ID length reported in PDU we received."
::= { ciiNotificationEntry 3 }
ciiPduMaxAreaAddress OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds the Max Area Addresses reported in a PDU
we received."
::= { ciiNotificationEntry 4 }
ciiPduProtocolVersion OBJECT-TYPE
SYNTAX CiiUnsigned8TC
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds the Protocol version reported in PDU we received."
::= { ciiNotificationEntry 5 }
ciiPduLspSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds the size of LSP we received that is too
big to forward."
::= { ciiNotificationEntry 6 }
ciiPduOriginatingBufferSize OBJECT-TYPE
SYNTAX CiiUnsigned16TC (0..16000)
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Holds the size of ciiSysLevelOrigLSPBuffSize advertised by
the peer in the originatingLSPBufferSize TLV."
::= { ciiNotificationEntry 7 }
ciiPduProtocolsSupported OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The list of protocols supported by an
adjacent system. This may be empty."
::= { ciiNotificationEntry 8 }
ciiAdjState OBJECT-TYPE
SYNTAX INTEGER
{
down (1),
initializing (2),
up (3),
failed(4)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The current state of an adjacency."
::= { ciiNotificationEntry 9 }
ciiErrorOffset OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"An offset to a problem in a PDU. If the problem
is a malformed TLV, this points to the beginning
of the TLV. If the problem is in the header, this
points to the byte that is suspicious."
::= { ciiNotificationEntry 10 }
ciiErrorTLVType OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The type for a malformed TLV."
::= { ciiNotificationEntry 11 }
ciiNotifManualAddress OBJECT-TYPE
SYNTAX CiiOSINSAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Manually configured area address used in
this notification."
::= { ciiNotificationEntry 12 }
ciiNotifIsLevelIndex OBJECT-TYPE
SYNTAX INTEGER
{
level1IS (1),
level2IS (2)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The index value used in this notification
to indicate the system level."
::= { ciiNotificationEntry 13 }
-- Type definitions
ciiDatabaseOverload NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiSysLevelOverloadState
}
STATUS current
DESCRIPTION
"This notification is generated when the system
enters or leaves the Overload state. The number
of times this has be generated and cleared is kept
track of by ciiSysStatLSPDbaseOloads."
::= { ciscoIetfIsisMIBNotifs 1 }
ciiManualAddressDrops NOTIFICATION-TYPE
OBJECTS {
ciiNotifManualAddress
}
STATUS current
DESCRIPTION
"This notification is generated when one of the
manual areaAddresses assigned to this system is
ignored when computing routes. The object
ciiNotifManualAddress describes the area that
has been dropped.
The number of times this event has been generated
is counted by ciiSysStatManAddrDropFromAreas.
This notification is edge triggered, and should not
be regenerated until an address that was used in
the previous computation has been dropped."
::= { ciscoIetfIsisMIBNotifs 2 }
ciiCorruptedLSPDetected NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiPduLspId
}
STATUS current
DESCRIPTION
"This notification is generated when we find that
an LSP that was stored in memory has become
corrupted. The number of times this has been
generated is counted by ciiSysStatCorrLSPs.
We forward an LSP ID. We may have independent
knowledge of the ID, but in some implementations
there is a chance that the ID itself will be
corrupted."
::= { ciscoIetfIsisMIBNotifs 3 }
ciiAttemptToExceedMaxSequence NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiPduLspId
}
STATUS current
DESCRIPTION
"When the sequence number on an LSP we generate
wraps the 32 bit sequence counter, we purge and
wait to re-announce this information. This
notification describes that event. Since these
should not be generated rapidly, we generate
an event each time this happens.
While the first 6 bytes of the LSPID are ours,
the other two contain useful information."
::= { ciscoIetfIsisMIBNotifs 4 }
ciiIDLenMismatch NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiPduFieldLen,
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a PDU
with a different value of the System ID Length.
This notification includes an index to identify
the circuit where we saw the PDU and the header of
the PDU which may help a network manager identify
the source of the confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received on the same circuit."
::= { ciscoIetfIsisMIBNotifs 5 }
ciiMaxAreaAddressesMismatch NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiPduMaxAreaAddress,
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a PDU
with a different value of the Maximum Area
Addresses. This notification includes the
header of the packet, which may help a
network manager identify the source of the
confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 6 }
ciiOwnLSPPurge NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduLspId
}
STATUS current
DESCRIPTION
"A notification sent when we receive a PDU
with our systemID and zero age. This
notification includes the circuit Index
and router ID from the LSP, if available,
which may help a network manager
identify the source of the confusion."
::= { ciscoIetfIsisMIBNotifs 7 }
ciiSequenceNumberSkip NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduLspId
}
STATUS current
DESCRIPTION
"When we receive an LSP with our System ID
and different contents, we may need to reissue
the LSP with a higher sequence number.
We send this notification if we need to increase
the sequence number by more than one. If two
Intermediate Systems are configured with the same
System ID, this notification will fire."
::= { ciscoIetfIsisMIBNotifs 8 }
ciiAuthenticationTypeFailure NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a PDU
with the wrong authentication type field.
This notification includes the header of the
packet, which may help a network manager
identify the source of the confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 9 }
ciiAuthenticationFailure NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a PDU
with incorrect authentication information
field. This notification includes the header
of the packet, which may help a network manager
identify the source of the confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 10 }
ciiVersionSkew NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduProtocolVersion,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a Hello
PDU from an IS running a different version
of the protocol. This notification includes
the header of the packet, which may help a
network manager identify the source of the
confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 11 }
ciiAreaMismatch NOTIFICATION-TYPE
OBJECTS {
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a Hello
PDU from an IS which does not share any
area address. This notification includes
the header of the packet, which may help a
network manager identify the source of the
confusion.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 12 }
ciiRejectedAdjacency NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when we receive a Hello
PDU from an IS, but do not establish an
adjacency for some reason.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the circuit."
::= { ciscoIetfIsisMIBNotifs 13 }
ciiLSPTooLargeToPropagate NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduLspSize,
ciiPduLspId
}
STATUS current
DESCRIPTION
"A notification sent when we attempt to propagate
an LSP which is larger than the dataLinkBlockSize
for the circuit.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 14 }
ciiOrigLSPBuffSizeMismatch NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduLspId,
ciiPduOriginatingBufferSize
}
STATUS current
DESCRIPTION
"A notification sent when a Level 1 LSP or Level
2 LSP is received which is larger than the local
value for ciiSysLevelOrigLSPBuffSize, or when an
LSP is received containing the originatingLSPBufferSize
option and the value in the PDU option field does
not match the local value for ciiSysLevelOrigLSPBuffSize.
We pass up the size from the option field or the
size of the LSP that exceeds our configuration.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 15 }
ciiProtocolsSupportedMismatch NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduProtocolsSupported,
ciiPduLspId,
ciiPduFragment
}
STATUS current
DESCRIPTION
"A notification sent when a non-pseudonode
segment 0 LSP is received that has no matching
protocols supported.
This may be because the system does not generate
the field, or because there are no common elements.
The list of protocols supported should be included
in the notification: it may be empty if the TLV
is not supported, or if the TLV is empty.
This should be an edge-triggered notification.
We should not send a second notification about
PDUs received from the same circuit."
::= { ciscoIetfIsisMIBNotifs 16 }
ciiAdjacencyChange NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiCircIfIndex,
ciiPduLspId,
ciiAdjState
}
STATUS current
DESCRIPTION
"A notification sent when an adjacency changes
state, entering or leaving state up.
The first 6 bytes of the ciiPduLspId are the
SystemID of the adjacent IS.
The ciiAdjState is the new state of the adjacency."
::= { ciscoIetfIsisMIBNotifs 17 }
ciiLSPErrorDetected NOTIFICATION-TYPE
OBJECTS {
ciiNotifIsLevelIndex,
ciiPduLspId,
ciiCircIfIndex,
ciiPduFragment,
ciiErrorOffset,
ciiErrorTLVType
}
STATUS current
DESCRIPTION
"This notification is generated when we receive
an LSP with a parse error. The ciiCircIfIndex
holds in index of the circuit on which the PDU
arrived. The ciiPduFragment holds start of the LSP,
and the ciiErrorOffset points to the problem.
If the problem is a mal-formed TLV, ciiErrorOffset
points to start of the TLV and ciiErrorTLVType
holds the value of the type.
If the problem is with the LSP header, ciiErrorOffset
points to the suspicious byte.
The number of such LSPs is accumulated in
ciiSysStatLSPErrors."
::= { ciscoIetfIsisMIBNotifs 18 }
-- Agent Conformance Definitions
-- We define the objects a conformant agent must define
ciscoIetfIsisMIBGroups OBJECT IDENTIFIER ::=
{ ciscoIetfIsisMIBConform 1 }
ciscoIetfIsisMIBCompliances OBJECT IDENTIFIER ::=
{ ciscoIetfIsisMIBConform 2 }
-- compliance statements
ciscoIetfIsisMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that support
the IS-IS MIB"
MODULE -- this module
MANDATORY-GROUPS {
ciscoIetfIsisSystemGroup,
ciscoIetfIsisCircuitGroup,
ciscoIetfIsisISAdjGroup,
ciscoIetfIsisNotifObjectGroup,
ciscoIetfIsisNotificationGroup
}
::= { ciscoIetfIsisMIBCompliances 1 }
-- List of all groups, mandatory and optional
ciscoIetfIsisMIBAdvCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that support
the IS-IS MIB"
MODULE -- this module
MANDATORY-GROUPS {
ciscoIetfIsisSystemGroup,
ciscoIetfIsisCircuitGroup,
ciscoIetfIsisISAdjGroup,
ciscoIetfIsisNotifObjectGroup,
ciscoIetfIsisNotificationGroup,
ciscoIetfIsisISPDUCounterGroup,
ciscoIetfIsisRATableGroup,
ciscoIetfIsisISIPRADestGroup,
ciscoIetfIsisLSPGroup
}
::= { ciscoIetfIsisMIBCompliances 2 }
-- MIB Grouping
ciscoIetfIsisSystemGroup OBJECT-GROUP
OBJECTS {
ciiSysVersion,
ciiSysType,
ciiSysID,
ciiSysMaxPathSplits,
ciiSysMaxLSPGenInt,
ciiSysPollESHelloRate,
ciiSysWaitTime,
ciiSysAdminState,
ciiSysL2toL1Leaking,
ciiSysMaxAge,
ciiSysLevelOrigLSPBuffSize,
ciiSysLevelMinLSPGenInt,
ciiSysLevelOverloadState,
ciiSysLevelSetOverload,
ciiSysLevelSetOverloadUntil,
ciiSysLevelMetricStyle,
ciiSysLevelSPFConsiders,
ciiSysLevelTEEnabled,
ciiSysReceiveLSPBufferSize,
ciiManAreaAddrExistState,
ciiAreaAddr,
ciiSysProtSuppExistState,
ciiSummAddrExistState,
ciiSummAddrMetric,
ciiSummAddrFullMetric,
ciiRedistributeAddrExistState,
ciiRouterHostName,
ciiRouterID,
ciiSysStatCorrLSPs,
ciiSysStatLSPDbaseOloads,
ciiSysStatManAddrDropFromAreas,
ciiSysStatAttmptToExMaxSeqNums,
ciiSysStatSeqNumSkips,
ciiSysStatOwnLSPPurges,
ciiSysStatIDFieldLenMismatches,
ciiSysStatPartChanges,
ciiSysStatSPFRuns,
ciiSysStatAuthTypeFails,
ciiSysStatAuthFails,
ciiSysStatLSPErrors
}
STATUS current
DESCRIPTION
"The collections of objects used to manage an
IS-IS router."
::= { ciscoIetfIsisMIBGroups 1 }
ciscoIetfIsisCircuitGroup OBJECT-GROUP
OBJECTS {
ciiNextCircIndex,
ciiCircIfSubIndex,
ciiCircAdminState,
ciiCircExistState,
ciiCircType,
ciiCircExtDomain,
ciiCircAdjChanges,
ciiCircNumAdj,
ciiCircInitFails,
ciiCircRejAdjs,
ciiCircIDFieldLenMismatches,
ciiCircMaxAreaAddrMismatches,
ciiCircAuthTypeFails,
ciiCircAuthFails,
ciiCircLANDesISChanges,
ciiCircLevel,
ciiCircPassiveCircuit,
ciiCircMeshGroupEnabled,
ciiCircMeshGroup,
ciiCircSmallHellos,
ciiCircLastUpTime,
ciiCirc3WayEnabled,
ciiCircExtendedCircID,
ciiCircIfIndex,
ciiCircLevelMetric,
ciiCircLevelWideMetric,
ciiCircLevelISPriority,
ciiCircLevelIDOctet,
ciiCircLevelID,
ciiCircLevelDesIS,
ciiCircLevelHelloMultiplier,
ciiCircLevelHelloTimer,
ciiCircLevelDRHelloTimer,
ciiCircLevelLSPThrottle,
ciiCircLevelMinLSPRetransInt,
ciiCircLevelCSNPInterval,
ciiCircLevelPartSNPInterval
}
STATUS current
DESCRIPTION
"The collection of objects used to describe in
IS-IS Circuit."
::= { ciscoIetfIsisMIBGroups 2 }
ciscoIetfIsisISAdjGroup OBJECT-GROUP
OBJECTS {
ciiISAdjState,
ciiISAdj3WayState,
ciiISAdjNeighSNPAAddress,
ciiISAdjNeighSysType,
ciiISAdjNeighSysID,
ciiISAdjNbrExtendedCircID,
ciiISAdjUsage,
ciiISAdjHoldTimer,
ciiISAdjNeighPriority,
ciiISAdjLastUpTime,
ciiISAdjAreaAddress,
ciiISAdjIPAddrType,
ciiISAdjIPAddrAddress,
ciiISAdjProtSuppProtocol
}
STATUS current
DESCRIPTION
"The collections of objects used to manage an
IS-IS Adjacency."
::= { ciscoIetfIsisMIBGroups 3 }
ciscoIetfIsisNotifObjectGroup OBJECT-GROUP
OBJECTS {
ciiPduLspId,
ciiPduFragment,
ciiPduFieldLen,
ciiPduMaxAreaAddress,
ciiPduProtocolVersion,
ciiPduLspSize,
ciiPduOriginatingBufferSize,
ciiPduProtocolsSupported,
ciiAdjState,
ciiErrorOffset,
ciiErrorTLVType,
ciiNotifManualAddress,
ciiNotifIsLevelIndex
}
STATUS current
DESCRIPTION
"The objects used to record notification parameters."
::= { ciscoIetfIsisMIBGroups 4 }
ciscoIetfIsisNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
ciiDatabaseOverload,
ciiManualAddressDrops,
ciiCorruptedLSPDetected,
ciiAttemptToExceedMaxSequence,
ciiIDLenMismatch,
ciiMaxAreaAddressesMismatch,
ciiOwnLSPPurge,
ciiSequenceNumberSkip,
ciiAuthenticationTypeFailure,
ciiAuthenticationFailure,
ciiVersionSkew,
ciiAreaMismatch,
ciiRejectedAdjacency,
ciiLSPTooLargeToPropagate,
ciiOrigLSPBuffSizeMismatch,
ciiProtocolsSupportedMismatch,
ciiAdjacencyChange,
ciiLSPErrorDetected
}
STATUS current
DESCRIPTION
"The collections of notifications sent by an IS."
::= { ciscoIetfIsisMIBGroups 5 }
ciscoIetfIsisISPDUCounterGroup OBJECT-GROUP
OBJECTS {
ciiPacketCountIIHellos,
ciiPacketCountISHellos,
ciiPacketCountESHellos,
ciiPacketCountLSPs,
ciiPacketCountCSNPs,
ciiPacketCountPSNPs,
ciiPacketCountUnknowns
}
STATUS current
DESCRIPTION
"The collections of objects used to count protocol PDUs."
::= { ciscoIetfIsisMIBGroups 6 }
ciscoIetfIsisRATableGroup OBJECT-GROUP
OBJECTS {
ciiRAExistState,
ciiRAAdminState,
ciiRAAddrPrefix,
ciiRAMapType,
ciiRAMetric,
ciiRAMetricType,
ciiRASNPAAddress,
ciiRASNPAMask,
ciiRASNPAPrefix,
ciiRAType
}
STATUS current
DESCRIPTION
"The collections of objects used to manage the
reachable NSAP prefixes."
::= { ciscoIetfIsisMIBGroups 7 }
ciscoIetfIsisISIPRADestGroup OBJECT-GROUP
OBJECTS {
ciiIPRANextHopType,
ciiIPRANextHop,
ciiIPRAType,
ciiIPRAExistState,
ciiIPRAAdminState,
ciiIPRAMetric,
ciiIPRAFullMetric,
ciiIPRAMetricType,
ciiIPRASNPAAddress,
ciiIPRASourceType
}
STATUS current
DESCRIPTION
"The collections of objects used to manage configured
IP addresses."
::= { ciscoIetfIsisMIBGroups 8 }
ciscoIetfIsisLSPGroup OBJECT-GROUP
OBJECTS {
ciiLSPSeq,
ciiLSPZeroLife,
ciiLSPChecksum,
ciiLSPLifetimeRemain,
ciiLSPPDULength,
ciiLSPAttributes,
ciiLSPTLVSeq,
ciiLSPTLVChecksum,
ciiLSPTLVType,
ciiLSPTLVLen,
ciiLSPTLVValue
}
STATUS current
DESCRIPTION
"The collections of objects used to observe the LSP
Data Base."
::= { ciscoIetfIsisMIBGroups 9 }
END
Reference in New Issue Copy Permalink