mibs/MIBS/cisco/CISCO-IF-EXTENSION-MIB

3483 lines
117 KiB
Plaintext
Raw Permalink Normal View History

2023-12-05 12:25:34 +01:00
-- *****************************************************************
-- Cisco Extension to the IF MIB
--
-- May 2002, Manik Raina
-- %DNP% Jun 2003, Sam Liang, Liwei Lue
-- %DNP% Jul 2003, Jayakumar Kadirvelu
-- %DNP% Aug 2003, Jayakumar Kadirvelu
-- %DNP% Aug 2004, Arul Mozhi
--
-- Copyright (c) 2002-2016, 2020 by cisco Systems Inc.
--
-- All rights reserved.
-- *************************************************************
CISCO-IF-EXTENSION-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Counter64,
Gauge32,
Unsigned32,
Integer32,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue,
TimeStamp,
DisplayString,
TEXTUAL-CONVENTION
FROM SNMPv2-TC
ifIndex,
InterfaceIndexOrZero,
ifName,
ifType,
ifAdminStatus,
ifOperStatus
FROM IF-MIB
entPhysicalIndex
FROM ENTITY-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
IfOperStatusReason
FROM CISCO-TC
ciscoMgmt
FROM CISCO-SMI;
ciscoIfExtensionMIB MODULE-IDENTITY
LAST-UPDATED "202011030000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
"Cisco Systems
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-core-mibs@cisco.com,
cs-lan-switch-snmp@cisco.com"
DESCRIPTION
"A MIB module for extending the IF-MIB (RFC2863)
to add objects which provide additional information
about interfaces not available in other MIBS.
This MIB replaces the OLD-CISCO-INTERFACES-MIB.
GLOSSARY :
Virtual Switch - A physical switch partitioned into
multiple logical switches.
Interface Sharing - An interface can be shared among
multiple virtual switches.
Speed Group - An interface is capable of operating in any one of
the speed range depending on the capability of the hardware.
Virtual Link (VL) - Virtual Link is a logical connectivity
between two end points. A physical interface can
have multiple Virtual Links.
No Drop Virtual Link - According to 802.3 standard,
No drop specifies lossless service on a virtual link.
Drop Virtual Link - According to 802.3 standard,
Traffic drop may occur on this virtual Link."
REVISION "202011030000Z"
DESCRIPTION
"Added cieIfDuplexCfgStatus and cieIfDuplexDetectStatus."
REVISION "201612010000Z"
DESCRIPTION
"Added enumerated value fourEightSixteenThirtyTwoG(5) to
cieIfSpeedGroupConfig."
REVISION "201303130000Z"
DESCRIPTION
"Added new object cieIfTransceiverFrequencyConfig,
cieIfFillPatternConfig, cieIfIgnoreBitErrorsConfig and
cieIfIgnoreInterruptThresholdConfig to cieIfInterfaceTable.
- Added a new group
ciscoIfExtensionTableIntfGroup3SupR02
- Deprecated ciscoIfExtensionMIBCompliance13
- Added ciscoIfExtensionMIBCompliance14."
REVISION "201209050000Z"
DESCRIPTION
"Added new object cieLinkUpDownConfig.
- Added a new group cieLinkUpDownNotifConfigGroup.
- Deprecated cieLinkUpDownEnable.
- Deprecated cieStandardLinkUpDownVarbinds.
- Deprecated ciscoIfExtensionMIBCompliance13.
- Added ciscoIfExtensionMIBCompliance14."
REVISION "201106270000Z"
DESCRIPTION
"Added new object cieIfSharedConfig and
cieIfSpeedGroupConfig to cieIfInterfaceTable.
Add cieIfVlStatsTable.
- Added a new group
ciscoIfExtensionTableIntfGroup3SupR01 and
cieIfVlStatsGroup
- Deprecated ciscoIfExtensionMIBCompliance12
- Added ciscoIfExtensionMIBCompliance13."
REVISION "200902260000Z"
DESCRIPTION
"Added Textual Convention InterfaceOwnershipList
- Added new object cieInterfaceOwnershipBitmap
- Added new group cieIfStatusListGroupSup1
- Deprecated ciscoIfExtensionMIBCompliance11
- Added ciscoIfExtensionMIBCompliance12"
REVISION "200812090000Z"
DESCRIPTION
"Added new object cieIfOwner to
cieIfInterfaceTable.
- Added a new group
ciscoIfExtensionTableIntfGroup3
- Deprecated ciscoIfExtensionTableIntfGroup2
- Deprecated ciscoIfExtensionMIBCompliance10
- Added ciscoIfExtensionMIBCompliance11"
REVISION "200810060000Z"
DESCRIPTION
"Added a new textual Convention IfIndexPersistenceState.
- Added scalar object cieIfIndexGlobalPersistence to
ciscoIfExtSystemConfig.
- Deprecated scalar object cieIfIndexPersistence to
ciscoIfExtSystemConfig.
- Added a new object cieIfIndexPersistenceControl in
cieIfIndexPersistenceTable.
- Deprecated an object cieIfIndexPersistenceEnabled in
cieIfIndexPersistenceTable.
- Added a new group cieIfIndexPersistenceControlGroup.
- Deprecated the group cieIfIndexPersistenceGroup.
- Added ciscoIfExtensionMIBCompliance10
- Deprecated ciscoIfExtensionMIBCompliance9"
REVISION "200807310000Z"
DESCRIPTION
"Added cieIfOperStatusCause to the objects in the
notification cieDelayedLinkUpDownNotif."
REVISION "200807080000Z"
DESCRIPTION
"Added notification cieDelayedLinkUpDownNotif
- Added scalar objects cieDelayedLinkUpDownNotifEnable and
cieDelayedLinkUpDownNotifDelay to ciscoIfExtSystemConfig.
- Added the following groups:
cieDelayedLinkUpDownNotifNotifGroup
cieDelayedLinkUpDownNotifNotifEnableGroup
- Deprecated ciscoIfExtensionMIBCompliance7
- Added ciscoIfExtensionMIBCompliance8."
REVISION "200806230000Z"
DESCRIPTION
"Added scalar object cieIfIndexPersistence to
ciscoIfExtSystemConfig.
- Added a new Table cieIfIndexPersistenceTable.
- Added a new object cieIfIndexPersistenceEnabled in
cieIfIndexPersistenceTable.
- Added a new group cieIfIndexPersistenceGroup.
- Deprecated ciscoIfExtensionMIBCompliance7
- Added ciscoIfExtensionMIBCompliance8"
REVISION "200707230000Z"
DESCRIPTION
"Added cieIfInterval in cieIfUtilTable. Changed
the description of objects in cieIfUtilTable.
Added ciscoIfExtUtilIntervalGroup."
REVISION "200611010000Z"
DESCRIPTION
"Add support for asymetrical interfaces speeds.
- Added following objects in cieIfInterfaceTable
cieIfSpeedReceive
cieIfHighSpeedReceive
- Added ciscoIfExtensionAsymmetricalSpeedGroup OBJECT-GROUP
- Added ciscoIfExtensionMIBCompliance6 MODULE-COMPLIANCE"
REVISION "200504280000Z"
DESCRIPTION
"Added:
- cieLinkUp & cieLinkDown notifications.
- object to control sending: only standard
linkUp/linkDown OR only cieLinkUp/cieLinkDown
OR both.
- object to control sending only standard defined
varbinds in linkUp/linkDown OR additional varbinds
in addition to standard defined."
REVISION "200501250000Z"
DESCRIPTION
"Updated the description of cieIfDot1dBaseMappingEntry."
REVISION "200409080000Z"
DESCRIPTION
"Added new objects 'cieIfOperStatusCause' and
'cieIfOperStatusCauseDescr' in cieIfInterfaceTable.
Added a new table 'cieIfStatusListTable'."
REVISION "200311140000Z"
DESCRIPTION
"Added new objects cieIfName and cieIfIndex for the
'ifName' to 'ifIndex' mapping. Deprecated the
ciscoIfExtensionMIBCompliance2 compliance.
Added ciscoIfExtensionMIBCompliance3 and
ciscoIfExtIfNameMappingGroup."
REVISION "200308120000Z"
DESCRIPTION
"Added ciscoIfExtDot1dBaseMappingGroup."
REVISION "200307170000Z"
DESCRIPTION
"Added ciscoIfExtUtilizationGroup."
REVISION "200306250000Z"
DESCRIPTION
"Added the object cieSystemMtu and
ciscoIfExtSystemGroup.
Added ciscoIfExtDot1qCustomEtherType and
ciscoIfExtDot1qEtherTypeGroup."
REVISION "200210120000Z"
DESCRIPTION
"Added the objects cieIfDhcpMode, cieIfMtu,
cieIfContextName to cieIfInterfaceTable.
Deprecated the ciscoIfExtensionMIBCompliance
compliance. Added ciscoIfExtensionMIBCompliance1.
Added ciscoIfExtensionTableIntfGroup1."
REVISION "200207240000Z"
DESCRIPTION
"Initial version of the MIB module."
::= { ciscoMgmt 276 }
ciscoIfExtensionMIBNotifications OBJECT IDENTIFIER
::= { ciscoIfExtensionMIB 0 }
ciscoIfExtensionMIBObjects OBJECT IDENTIFIER
::= { ciscoIfExtensionMIB 1 }
ciscoIfExtensionMIBConformance OBJECT IDENTIFIER
::= { ciscoIfExtensionMIB 2 }
ciscoIfExtensionStats OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 1 }
ciscoIfExtSystemConfig OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 2 }
ciscoIfExtDot1qCustomEtherType OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 3 }
ciscoIfExtUtilization OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 4 }
ciscoIfExtDot1dBaseMapping OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 5 }
ciscoIfExtIfNameMapping OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBObjects 6 }
-- Textual Conventions
InterfaceIndexList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines the 'ifIndex' for a
set of 64 interfaces in a module.
Each 4 bytes within the value of an object of this
type is combined together to represent the interface
index of a particular port in the module (i.e., each
4 byte group represents the 'ifIndex' of an interface).
The first 4 bytes (byte 1, byte 2, byte 3 and byte 4)
combined represent the 'ifIndex' of an interface.
While the second 4 bytes (byte 5, byte 6, byte 7 and
byte 8) represent the 'ifIndex' for the next interface
in the module, and so on.
If there are only 'n' interfaces in a set of 64
interfaces in the module, then bytes after the '4n'
byte in this object are irrelevant."
SYNTAX OCTET STRING (SIZE (0..256))
InterfaceOperModeList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines the operational mode
for a set of 64 interfaces in a module.
The operational mode of an interface is represented
by the value defined in the textual convention
'InterfaceOperMode' (defined in CISCO-ST-TC).
Each 'byte' within the value of an object of this
type, specifies the operational mode of an interface
in the module.
The first byte (byte 1) represents the operational
mode of an interface in the module, whose 'ifIndex'
is represented by the corresponding instance of
'cieInterfacesIndex' object in its first 4 bytes.
The second byte (byte 2) represents the operational
mode of an interface in the module, whose 'ifIndex'
is represented by the corresponding instance of
'cieInterfacesIndex' object in its second 4 bytes.
If there are only 'n' interfaces in a set of 64
interfaces in the module, then bytes after the 'n'
byte in this object are irrelevant."
SYNTAX OCTET STRING (SIZE (0..64))
InterfaceOperCauseList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines the operational
status cause for a set of 64 interfaces in a module.
The operational status cause of an interface is
represented by the value defined in the textual
convention 'IfOperStatusReason' (defined in CISCO-TC).
Each 2 bytes within the value of an object of this
type is combined together to represent the operational
status cause of a particular interface in the module
(i.e., each 2 byte group represents the
'cieIfOperStatusCause' of an interface).
The first 2 bytes (byte 1 and byte 2) of this object,
represents the operational status cause of an
interface in the module, whose 'ifIndex' is
represented by the corresponding instance of
'cieInterfacesIndex' object in its first 4 bytes.
The next 2 bytes (byte 3 and byte 4) of this object,
represents the operational status cause of an
interface in the module, whose 'ifIndex' is
represented by the corresponding instance of
'cieInterfacesIndex' object in the next 4 bytes
respectively.
If there are only 'n' interfaces in a set of 64
interfaces in the module, then bytes after the
'2n' byte in this object are irrelevant."
SYNTAX OCTET STRING (SIZE (0..128))
InterfaceOwnershipList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines the status for a set of
64 interfaces in a module regarding whether or not each
interface is administratively assigned a name of the current
owner of the interface resource as per the object cieIfOwner,
defined on that interface.
Each 'bit' within the value of an object of this type,
specifies whether the corresponding interface on the module
has been administratively assigned a name of the current
owner of the interface resource. In other words, each bit
represents whether the corresponding interface is 'owned'
or not. This bit is set to 1 if the interface is owned.
It is 0 otherwise.
The first bit (bit 1) in byte 1 represents whether the
interface, whose 'ifIndex' is represented by the corresponding
instance of 'cieInterfacesIndex' object in its first 4 bytes,
is owned or not.
The second byte (byte 2) in byte 2 represents whether the
interface, whose 'ifIndex' is represented by the corresponding
instance of 'cieInterfacesIndex' object in its second 4 bytes,
is owned or not.
If there are only 'n' interfaces in a set of 64 interfaces in
the module, then bits after the 'n' bit in this object are
irrelevant and set to 0."
SYNTAX OCTET STRING (SIZE (0..8))
IfIndexPersistenceState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention is used to define the state of ifIndex
Persistence for both global as well as interface level.
The global object, cieIfIndexGlobalPersistence can have two
state of ifIndex Persistence i.e. either enable or disable. At
interface level, the object cieIfIndexPersistenceControl can
take all the three values enable/disable/global."
SYNTAX INTEGER {
disable(1),
enable(2),
global(3)
}
-- CISCO IF Extension Packet Stats Table
cieIfPacketStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfPacketStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains interface packet
statistics which are not available in
IF-MIB(RFC2863).
As an example, some interfaces to which
objects in this table are applicable are
as follows :
o Ethernet
o FastEthernet
o ATM
o BRI
o Sonet
o GigabitEthernet
Some objects defined in this table may be
applicable to physical interfaces only.
As a result, this table may be sparse for
some logical interfaces."
::= { ciscoIfExtensionStats 1 }
cieIfPacketStatsEntry OBJECT-TYPE
SYNTAX CieIfPacketStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry into the cieIfPacketStatsTable."
INDEX { ifIndex }
::= { cieIfPacketStatsTable 1 }
CieIfPacketStatsEntry ::= SEQUENCE {
cieIfLastInTime Gauge32,
cieIfLastOutTime Gauge32,
cieIfLastOutHangTime Gauge32,
cieIfInRuntsErrs Counter32,
cieIfInGiantsErrs Counter32,
cieIfInFramingErrs Counter32,
cieIfInOverrunErrs Counter32,
cieIfInIgnored Counter32,
cieIfInAbortErrs Counter32,
cieIfInputQueueDrops Counter32,
cieIfOutputQueueDrops Counter32,
cieIfPacketDiscontinuityTime TimeStamp
}
-- The following section describes the objects in the table
-- in greater detail.
cieIfLastInTime OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the elapsed time in
milliseconds since last protocol input
packet was received.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 1 }
cieIfLastOutTime OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the elapsed time in
milliseconds since last protocol output
packet was transmitted.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 2 }
cieIfLastOutHangTime OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the elapsed time in
milliseconds since last protocol output
packet could not be successfully transmitted.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 3 }
cieIfInRuntsErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets input on a particular
physical interface which were dropped as
they were smaller than the minimum allowable
physical media limit.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 4 }
cieIfInGiantsErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input packets on a particular
physical interface which were dropped as
they were larger than the ifMtu (largest
permitted size of a packet which can be
sent/received on an interface).
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 5 }
cieIfInFramingErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input packets on a physical
interface which were misaligned or had
framing errors. This happens when the
format of the incoming packet on a physical
interface is incorrect.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 6 }
cieIfInOverrunErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input packets which arrived
on a particular physical interface which
were too quick for the hardware to receive
and hence the receiver ran out of buffers.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 7 }
cieIfInIgnored OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input packets which were simply
ignored by this physical interface due to
insufficient resources to handle the incoming
packets.
For example, this could indicate that the input
receive buffers are not available or that the
receiver lost a packet.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 8 }
cieIfInAbortErrs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of input packets which were dropped
because the receiver aborted.
Examples of this could be when an abort
sequence aborted the input frame or when
there is a collision in an ethernet segment.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 9 }
cieIfInputQueueDrops OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input packets which were
dropped.
Some reasons why this object could be
incremented are:
o Input queue is full.
o Errors at the receiver hardware
while receiving the packet.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 10 }
cieIfOutputQueueDrops OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of output
packets dropped by the interface even though
no error had been detected to prevent them
being transmitted.
The packet could be dropped for many reasons,
which could range from the interface being
down to errors in the format of the packet.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfPacketDiscontinuityTime."
::= { cieIfPacketStatsEntry 11 }
cieIfPacketDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent
occasion at which this interface's counters
suffered a discontinuity.
If no such discontinuities have occurred
since the last re-initialization of the
local management subsystem, then this
object contains a value of zero."
::= { cieIfPacketStatsEntry 12 }
-- Cisco IF Extension Interface Table
cieIfInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects which provide
more information about interface
properties not available in IF-MIB
(RFC 2863).
Some objects defined in this table may be
applicable to physical interfaces only.
As a result, this table may be sparse for
logical interfaces."
::= { ciscoIfExtensionStats 2 }
cieIfInterfaceEntry OBJECT-TYPE
SYNTAX CieIfInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry into the cieIfInterfaceTable."
INDEX { ifIndex }
::= { cieIfInterfaceTable 1 }
CieIfInterfaceEntry ::= SEQUENCE {
cieIfResetCount Counter32,
cieIfKeepAliveEnabled TruthValue,
cieIfStateChangeReason SnmpAdminString,
cieIfCarrierTransitionCount Counter32,
cieIfInterfaceDiscontinuityTime TimeStamp,
cieIfDhcpMode TruthValue,
cieIfMtu Integer32,
cieIfContextName OCTET STRING,
cieIfOperStatusCause IfOperStatusReason,
cieIfOperStatusCauseDescr SnmpAdminString,
cieIfSpeedReceive Gauge32,
cieIfHighSpeedReceive Gauge32,
cieIfOwner DisplayString,
cieIfSharedConfig INTEGER,
cieIfSpeedGroupConfig INTEGER,
cieIfTransceiverFrequencyConfig INTEGER,
cieIfFillPatternConfig INTEGER,
cieIfIgnoreBitErrorsConfig TruthValue,
cieIfIgnoreInterruptThresholdConfig TruthValue,
cieIfDuplexCfgStatus INTEGER,
cieIfDuplexDetectStatus INTEGER
}
cieIfResetCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the interface was
internally reset and brought up.
Some of the actions which can cause this
counter to increment are :
o Bringing an interface up using the
interface CLI command.
o Clearing the interface with the exec
CLI command.
o Bringing the interface up via SNMP.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfInterfaceDiscontinuityTime."
::= { cieIfInterfaceEntry 1 }
cieIfKeepAliveEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A keepalive is a small, layer-2 message
that is transmitted by a network device
to let directly-connected network devices
know of its presence.
This object returns 'true' if keepalives
are enabled on this interface. If keepalives
are not enabled, 'false' is returned.
Setting this object to TRUE or FALSE enables
or disables (respectively) keepalive on this
interface."
::= { cieIfInterfaceEntry 2 }
cieIfStateChangeReason OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object displays a human-readable
textual string which describes the
cause of the last state change of the
interface.
Examples of the values this object
can take are:
o 'Lost Carrier'
o 'administratively down'
o 'up'
o 'down'"
::= { cieIfInterfaceEntry 3 }
cieIfCarrierTransitionCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times interface saw the carrier
signal transition.
For example, if a T1 line is unplugged,
then framer will detect the loss of signal
(LOS) on the line and will count it as a
transition.
Discontinuities in the value of this variable
can occur at re-initialization of the
management system, and at other times as
indicated by the values of
cieIfInterfaceDiscontinuityTime."
::= { cieIfInterfaceEntry 4 }
cieIfInterfaceDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent
occasion at which this interface's counters
suffered a discontinuity.
If no such discontinuities have occurred
since the last re-initialization of the
local management subsystem, then this
object contains a value of zero."
::= { cieIfInterfaceEntry 5 }
cieIfDhcpMode OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DHCP mode configured by the
administrator.
If 'true' the DHCP is enabled. In which
case an IP address is requested in DHCP.
This is in addition to any that are
configured by the administrator in
'ciiIPAddressTable' or 'ciiIPIfAddressTable'
in CISCO-IP-IF-MIB.
If 'false' the DHCP is disabled. In which
case all IP addresses are configured by the
administrator in 'ciiIPAddressTable' or
'ciiIPIfAddressTable'.
For interfaces, for which DHCP cannot be or
is not supported, then this object has the
value 'false'."
DEFVAL { false }
::= { cieIfInterfaceEntry 6 }
cieIfMtu OBJECT-TYPE
SYNTAX Integer32 (40..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The MTU configured by the administrator.
This object is exactly same as 'ifMtu' in
ifTable from IF-MIB for the same ifIndex
value , except that it is configurable by the
administrator. For more description of this
object refer to 'ifMtu' in IF-MIB."
DEFVAL { 1500 }
::= { cieIfInterfaceEntry 7 }
cieIfContextName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ContextName denotes the interface
'context' and is used to logically separate
the MIB management.
RFC 2571 and RFC 2737 describe this approach.
When the agent supports a different SNMP
context, as detailed in RFC 2571 and
RFC 2737, for different interfaces, then the
value of this object specifies the context
name used for this interface."
DEFVAL { "" }
::= { cieIfInterfaceEntry 8 }
cieIfOperStatusCause OBJECT-TYPE
SYNTAX IfOperStatusReason
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the detailed
operational cause reason for the current
operational state of the interface.
The current operational state of the interface
is given by the 'ifOperStatus' defined
in IF-MIB.
The corresponding instance of
'cieIfOperStatusCauseDescr' must be used to
get the information about the operational
cause value mentioned in this object.
For interfaces whose 'ifOperStatus' is 'down'
the objects 'cieIfOperStatusCause' and
'cieIfOperStatusCauseDescr' together provides
the information about the operational cause
reason and the description of the cause.
The value of this object will be 'none' for
all the 'ifOperStatus' values except for
'down'. Its value will be one status cause
defined in the 'IfOperStatusReason' textual
convention if 'ifOperStatus' is 'down'.
The value of this object will be 'other'
if the operational status cause is not one
defined in 'IfOperStatusReason'."
::= { cieIfInterfaceEntry 9 }
cieIfOperStatusCauseDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description for the cause of current
operational state of the interface, given
by the object 'cieIfOperStatusCause'.
For an interface whose 'ifOperStatus' is not
'down' the value of this object will be
'none'."
::= { cieIfInterfaceEntry 10 }
cieIfSpeedReceive OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the interface's current receive bandwidth in
bits per second. This object is provided for interface with
asymmetric interface speeds like ADSL and should be used in
conjunction with ifSpeed object. For interfaces which do not
vary in bandwidth or for those where no accurate estimation can
be made, this object should contain the nominal bandwidth. If
the bandwidth of the interface is greater than the maximum value
reportable by this object then this object should report its
maximum value (4,294,967,295) and ifHighSpeed must be used to
report the interace's speed. For a sub-layer which has no
concept of bandwidth, this object should be zero."
::= { cieIfInterfaceEntry 11 }
cieIfHighSpeedReceive OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the interface's current receive bandwidth in
units of 1,000,000 bits per second. If this object reports a
value of `n' then the speed of the interface is somewhere in the
range of `n-500,000' to `n+499,999'. For interfaces which do
not vary in bandwidth or for those where no accurate estimation
can be made, this object should contain the nominal bandwidth.
For a sub-layer which has no concept of bandwidth, this object
should be zero."
::= { cieIfInterfaceEntry 12 }
cieIfOwner OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..80))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This data type is used to model an administratively assigned
name of the current owner of the interface resource. This
information is taken from the NVT ASCII character set. It is
suggested that this name contain one or more of the following:
SnmpEngineID, IP address, management station name, network
manager's name, location, or phone number.
SNMP access control is articulated entirely in terms of the
contents of MIB views; access to a particular SNMP object
instance depends only upon its presence or absence in a
particular MIB view and never upon its value or the value of
related object instances.
Thus, this object affords resolution of resource contention
only among cooperating managers; this object realizes no access
control function with respect to uncooperative parties."
::= { cieIfInterfaceEntry 13 }
cieIfSharedConfig OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
ownerDedicated(2),
ownerShared(3),
sharedOnly(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current configuration of
interface sharing on the given interface.
'notApplicable' - the interface sharing configuration on
this interface is not applicable.
'ownerDedicated' - the interface is in the dedicated mode
to the binding physical interface.
'ownerShared' - the interface is shared amongst virtual switches
and this interface physically belongs to a its
virtual switch.
'sharedOnly' - the interface is in purely shared mode."
::= { cieIfInterfaceEntry 14 }
cieIfSpeedGroupConfig OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
tenG(2),
oneTwoFourEightG(3),
twoFourEightSixteenG(4),
fourEightSixteenThirtyTwoG(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the current speed group
configuration on the given interface.
'notApplicable' - the interface speed group configuration on
this interface is not applicable. It is a
read-only value.
'10G' - the interface speed group configuration on
this interface as 10G.
'1G-2G-4G-8G' - the interface speed group configuration
on this interface as 1G-2G-4G-8G.
'2G-4G-8G-16G' - the interface speed group configuration
on this interface as 2G-4G-8G-16G.
'4G-8G-16G-32G' - the interface speed group configuration
on this interface as 4G-8G-16G-32G."
::= { cieIfInterfaceEntry 15 }
cieIfTransceiverFrequencyConfig OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
fibreChannel(2),
ethernet(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the current transceiver frequency
configuration on the given interface.
'notApplicable' - the interface transceiver frequency
configuration on this interface
is not applicable. It is a read-only value.
'FibreChannel' - the interface transceiver frequency
configuration on this interface as
Fibre Channel.
'Ethernet' - the interface transceiver frequency on
this interface as Ethernet."
DEFVAL { fibreChannel }
::= { cieIfInterfaceEntry 16 }
cieIfFillPatternConfig OBJECT-TYPE
SYNTAX INTEGER {
arbff8G(1),
idle8G(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the current switchport fill pattern
configuration on the given interface.
'arbff8G' - the inter frame gap fill pattern is
ARBFF for 8G speed.
'idle8G' - the inter frame gap fill pattern is
IDLE for 8G speed."
DEFVAL { arbff8G }
::= { cieIfInterfaceEntry 17 }
cieIfIgnoreBitErrorsConfig OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the current switchport biterrors
configuration on the given interface.
If 'true(1)' the ignore bit errors is enabled.In which case
the interface ignores bit errors.
If 'false(2)' the ignore bit errors is disabled. In which
case the interface acts on the bit errors.
For interfaces, for which bit errors
is not supported, then this object has the
value 'true(1)'."
DEFVAL { true }
::= { cieIfInterfaceEntry 18 }
cieIfIgnoreInterruptThresholdConfig OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the current interrupt threshold
configuration on the given interface.
'If 'true(1)' the ignore interrupt thresholds is enabled.
In which case the interface ignores interrupt thresholds.
If 'false(2)' the ignore interrupt thresholds is disabled.
In which case the interface acts on the interrupt
thresholds.
For interfaces, for which interrupt thresholds
is not supported, then this object has the
value 'true(1)'."
DEFVAL { true }
::= { cieIfInterfaceEntry 19 }
cieIfDuplexCfgStatus OBJECT-TYPE
SYNTAX INTEGER {
full(0),
half(1),
auto(2),
unsupported(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the configured duplex status on the
given interface."
::= { cieIfInterfaceEntry 20 }
cieIfDuplexDetectStatus OBJECT-TYPE
SYNTAX INTEGER {
full(0),
half(1),
auto(2),
unknown(3),
invalid(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the detected duplex status on the
given interface."
::= { cieIfInterfaceEntry 21 }
-- Cisco IF Extension Interface Status List Table
cieIfStatusListTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfStatusListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects for providing
the 'ifIndex', interface operational mode and
interface operational cause for all the
interfaces in the modules.
This table contains one entry for each
64 interfaces in an module.
This table provides efficient way of encoding
'ifIndex', interface operational mode and
interface operational cause, from the point
of retrieval, by combining the values a set
of 64 interfaces in a single MIB object."
::= { ciscoIfExtensionStats 3 }
cieIfStatusListEntry OBJECT-TYPE
SYNTAX CieIfStatusListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the 'ifIndex',
interface operational mode and interface
operational cause for a set of 64 interfaces
in a module."
INDEX {
entPhysicalIndex,
cieIfStatusListIndex
}
::= { cieIfStatusListTable 1 }
CieIfStatusListEntry ::= SEQUENCE {
cieIfStatusListIndex Unsigned32,
cieInterfacesIndex InterfaceIndexList,
cieInterfacesOperMode InterfaceOperModeList,
cieInterfacesOperCause InterfaceOperCauseList,
cieInterfaceOwnershipBitmap InterfaceOwnershipList
}
cieIfStatusListIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..33554432)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer value, greater than
zero, which identifies a list of 64 interfaces
within a module."
::= { cieIfStatusListEntry 1 }
cieInterfacesIndex OBJECT-TYPE
SYNTAX InterfaceIndexList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 'ifIndex' for a
set of 64 interfaces in the module."
::= { cieIfStatusListEntry 2 }
cieInterfacesOperMode OBJECT-TYPE
SYNTAX InterfaceOperModeList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the operational mode
for a set of 64 interfaces in the module."
::= { cieIfStatusListEntry 3 }
cieInterfacesOperCause OBJECT-TYPE
SYNTAX InterfaceOperCauseList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the operational status
cause for a set of 64 interfaces in the
module."
::= { cieIfStatusListEntry 4 }
cieInterfaceOwnershipBitmap OBJECT-TYPE
SYNTAX InterfaceOwnershipList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the status for a set of 64 interfaces
in a module regarding whether or not each interface is
administratively assigned a name of the current owner of the
interface resource as per cieIfOwner."
::= { cieIfStatusListEntry 5 }
cieIfVlStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfVlStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains VL (Virtual Link) statistics
for a capable interface.
Objects defined in this table may be
applicable to physical interfaces only."
::= { ciscoIfExtensionStats 4 }
cieIfVlStatsEntry OBJECT-TYPE
SYNTAX CieIfVlStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row contains managed objects for
Virtual Link statistics on interface capable of
providing this information."
INDEX { ifIndex }
::= { cieIfVlStatsTable 1 }
CieIfVlStatsEntry ::= SEQUENCE {
cieIfNoDropVlInPkts Counter64,
cieIfNoDropVlInOctets Counter64,
cieIfNoDropVlOutPkts Counter64,
cieIfNoDropVlOutOctets Counter64,
cieIfDropVlInPkts Counter64,
cieIfDropVlInOctets Counter64,
cieIfDropVlOutPkts Counter64,
cieIfDropVlOutOctets Counter64
}
cieIfNoDropVlInPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of input
packets on all No-Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 1 }
cieIfNoDropVlInOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of input
octets on all No-Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 2 }
cieIfNoDropVlOutPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of output
packets on all No-Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 3 }
cieIfNoDropVlOutOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of output
octets on all No-Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 4 }
cieIfDropVlInPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of input
packets on all Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 5 }
cieIfDropVlInOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of input
octets on all Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 6 }
cieIfDropVlOutPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of output
packets on all Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 7 }
cieIfDropVlOutOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of output
octets on all Drop Virtual Links belonged
to this interface."
::= { cieIfVlStatsEntry 8 }
-- Cisco IF Extension System Config
cieSystemMtu OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global system MTU in octets.
This object specifies the MTU on all interfaces.
However, the value specified by cieIfMtu
takes precedence for an interface, which means
that the interface's MTU uses the value
specified by cieIfMtu, if it is configured."
DEFVAL { 1500 }
::= { ciscoIfExtSystemConfig 1 }
cieLinkUpDownEnable OBJECT-TYPE
SYNTAX BITS {
standard(0),
cisco(1)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Indicates whether cieLinkUp/cieLinkDown
or standard mib-II defined linkUp/Down or
both, notifications should be generated
for the interfaces in the system.
'standard' - only generate standard defined
mib-II linkUp/linkDown notification
if 'ifLinkUpDownTrapEnable' for
the interface is 'enabled'.
'cisco' - only generate cieLinkUp/cieLinkDown
notifications for an interface if
the 'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
If both bits are selected then linkUp/linkDown and
cieLinkUp/cieLinkDown are both generated for an
interface if the 'ifLinkUpDownTrapEnable' for the
interface is 'enabled'."
DEFVAL { { standard } }
::= { ciscoIfExtSystemConfig 2 }
cieStandardLinkUpDownVarbinds OBJECT-TYPE
SYNTAX INTEGER {
standard(1),
additional(2),
other(3)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Indicates whether to send the extra
varbinds in addition to the varbinds defined
in linkUp/linkDown notifications.
'standard' - only send the varbinds defined in
the standard linkUp/linkDown
notification.
'additional' - send the extra varbinds in addition
to the defined ones.
'other' - any other config not covered by the above.
This value is read-only."
DEFVAL { additional }
::= { ciscoIfExtSystemConfig 3 }
cieIfIndexPersistence OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies whether ifIndex values persist across
reinitialization of the device.
ifIndex persistence means that the mapping between the ifDescr
object values and the ifIndex object values will be retained
across reboots.
Applications such as device inventory, billing, and fault
detection depend on the maintenance of the correspondence
between particular ifIndex values and their interfaces. During
reboot or insertion of a new card, the data to correlate the
interfaces to the ifIndex may become invalid in absence of
ifIndex persistence feature.
ifIndex persistence for an interface ensures ifIndex value for
the interface will remain the same after a system reboot.
Hence, this feature allows users to avoid the workarounds
required for consistent interface identification across
reinitialization.
Due to change in syntax, this object is deprecated by
cieIfIndexGlobalPersistence."
DEFVAL { false }
::= { ciscoIfExtSystemConfig 4 }
cieIfIndexPersistenceTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfIndexPersistenceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configuration data relating to ifIndex
persistence.
This table has a sparse dependent relationship on the ifTable,
containing a row for each ifEntry corresponding to an interface
for which ifIndex persistence is supported."
::= { ciscoIfExtSystemConfig 5 }
cieIfIndexPersistenceEntry OBJECT-TYPE
SYNTAX CieIfIndexPersistenceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents ifindex persistence configuration for an
interface specified by ifIndex. Whenever an interface which
supports ifindex persistence is created/destroyed in the
ifTable, the corresponding ifindex persistence entry is
created/destroyed respectively. Some of the interfaces may not
support ifindex persistence, for example, a dynamic interface,
such as a PPP connection or a IP subscriber interface."
INDEX { ifIndex }
::= { cieIfIndexPersistenceTable 1 }
CieIfIndexPersistenceEntry ::= SEQUENCE {
cieIfIndexPersistenceEnabled TruthValue,
cieIfIndexPersistenceControl IfIndexPersistenceState
}
cieIfIndexPersistenceEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies whether the interface's ifIndex value
persist across reinitialization.
Due to change in syntax, this object is deprecated by
cieIfIndexPersistenceControl."
DEFVAL { true }
::= { cieIfIndexPersistenceEntry 1 }
cieIfIndexPersistenceControl OBJECT-TYPE
SYNTAX IfIndexPersistenceState
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the interface's ifIndex value
persist across reinitialization. In global state, the interface
uses the global setting data for persistence i.e.
cieIfIndexGlobalPersistence."
DEFVAL { global }
::= { cieIfIndexPersistenceEntry 2 }
cieDelayedLinkUpDownNotifEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the system generates a
cieDelayedLinkUpDownNotif notification."
DEFVAL { false }
::= { ciscoIfExtSystemConfig 6 }
cieDelayedLinkUpDownNotifDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..60)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the interval of time an interface's
operational status must remain stable following a transition
before the system will generate a cieDelayedLinkUpDownNotif."
DEFVAL { 4 }
::= { ciscoIfExtSystemConfig 7 }
cieIfIndexGlobalPersistence OBJECT-TYPE
SYNTAX IfIndexPersistenceState
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether ifIndex values persist across
reinitialization of the device.
ifIndex persistence means that the mapping between the ifDescr
object values and the ifIndex object values will be retained
across reboots.
Applications such as device inventory, billing, and fault
detection depend on the maintenance of the correspondence
between particular ifIndex values and their interfaces. During
reboot or insertion of a new card, the data to correlate the
interfaces to the ifIndex may become invalid in absence of
ifIndex persistence feature.
ifIndex persistence for an interface ensures ifIndex value for
the interface will remain the same after a system reboot. Hence,
this feature allows users to avoid the workarounds required for
consistent interface identification across reinitialization.
The allowed values for this object are either enable or disable.
global value is not allowed."
DEFVAL { disable }
::= { ciscoIfExtSystemConfig 8 }
cieLinkUpDownConfig OBJECT-TYPE
SYNTAX BITS {
standardLinkUp(0),
standardLinkDown(1),
additionalLinkUp(2),
additionalLinkDown(3),
ciscoLinkUp(4),
ciscoLinkDown(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether standard mib-II defined linkUp/
linkDown, extended linkUp/linkDown (with extra varbinds in
addition to the varbinds defined in linkUp/linkDown) or
cieLinkUp/cieLinkDown notifications should be generated for
the interfaces in the system.
'standardLinkUp' - generate standard defined mib-II
linkUp notification if
'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
'standardLinkDown' - generate standard defined mib-II
linkDown notification if
'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
'additionalLinkUp' - generate linkUp notification with
additional varbinds if
'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
'additionalLinkDown' - generate linkDown notification with
additional varbinds if
'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
'ciscoLinkUp' - generate cieLinkUp notification
if the 'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
'ciscoLinkDown' - generate cieLinkDown notification
if the 'ifLinkUpDownTrapEnable' for the
interface is 'enabled'.
If multiple bits are set then multiple notifications will
be generated for an interface if the 'ifLinkUpDownTrapEnable'
for the interface is 'enabled'."
::= { ciscoIfExtSystemConfig 9 }
-- Cisco IF Extension Dot1q Custom EtherType Table
cieIfDot1qCustomEtherTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfDot1qCustomEtherTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of the interfaces that support
the 802.1q custom Ethertype feature."
::= { ciscoIfExtDot1qCustomEtherType 1 }
cieIfDot1qCustomEtherTypeEntry OBJECT-TYPE
SYNTAX CieIfDot1qCustomEtherTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing the custom EtherType
information for the interface.
Only interfaces with custom 802.1q
ethertype control are listed in the
table."
INDEX { ifIndex }
::= { cieIfDot1qCustomEtherTypeTable 1 }
CieIfDot1qCustomEtherTypeEntry ::= SEQUENCE {
cieIfDot1qCustomAdminEtherType Integer32,
cieIfDot1qCustomOperEtherType Integer32
}
cieIfDot1qCustomAdminEtherType OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Dot1qEtherType allow administrator
to select a non-standard (other than 0x8100)
2-byte ethertype for the interface to
interoperate with third party vendor's system
that do not use the standard 0x8100 ethertype
to identify 802.1q-tagged frames.
The current administrative value of the
802.1q ethertype for the interface. The
administrative 802.1q ethertype value may
differ from the operational 802.1q ethertype
value. On some platforms, 802.1q ethertype
may be assigned per group rather than per port.
If multiple ports belong to a port group,
the 802.1q ethertype assigned to any of
the ports in such group will apply to all
ports in the same group.
To configure non-standard dot1q ethertype
is only recommended when the Cisco device
is connected to any third party vendor device.
Also be advised that the custom ethertype value
needs to be changed in the whole cloud of
Cisco device with the same custom ethertype
value if the third party device are separated
by number of Cisco device in the middle."
::= { cieIfDot1qCustomEtherTypeEntry 1 }
cieIfDot1qCustomOperEtherType OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current operational value of the
802.1q ethertype for the interface."
::= { cieIfDot1qCustomEtherTypeEntry 2 }
-- Interface Utlization Group
cieIfUtilTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfUtilEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the interface utilization
rates for inbound and outbound traffic on an
interface."
::= { ciscoIfExtUtilization 1 }
cieIfUtilEntry OBJECT-TYPE
SYNTAX CieIfUtilEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing utilization rates for the
interface.
Every interface for which the inbound and
outbound traffic information is available
has a corresponding entry in this table."
INDEX { ifIndex }
::= { cieIfUtilTable 1 }
CieIfUtilEntry ::= SEQUENCE {
cieIfInPktRate Counter64,
cieIfInOctetRate Counter64,
cieIfOutPktRate Counter64,
cieIfOutOctetRate Counter64,
cieIfInterval Unsigned32
}
cieIfInPktRate OBJECT-TYPE
SYNTAX Counter64
UNITS "packets per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"By default, this is the five minute
exponentially-decayed moving average of the
inbound packet rate for this interface.
However, if the corresponding instance of
cieIfInterval is instantiated with a value
which specifies an interval different from
5-minutes, then cieIfInPktRate is the
exponentially-decayed moving average of inbound
packet rate over this different time interval."
::= { cieIfUtilEntry 1 }
cieIfInOctetRate OBJECT-TYPE
SYNTAX Counter64
UNITS "octets per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"By default, this is the five minute
exponentially-decayed moving average of the
inbound octet rate for this interface.
However, if the corresponding instance of
cieIfInterval is instantiated with a value
which specifies an interval different from
5-minutes, then cieIfInOctetRate is the
exponentially-decayed moving average of inbound
octet rate over this different time interval."
::= { cieIfUtilEntry 2 }
cieIfOutPktRate OBJECT-TYPE
SYNTAX Counter64
UNITS "packets per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"By default, this is the five minute
exponentially-decayed moving average of the
outbound packet rate for this interface.
However, if the corresponding instance of
cieIfInterval is instantiated with a value
which specifies an interval different from
5-minutes, then cieIfOutPktRate is the
exponentially-decayed moving average of outbound
packet rate over this different time interval."
::= { cieIfUtilEntry 3 }
cieIfOutOctetRate OBJECT-TYPE
SYNTAX Counter64
UNITS "octets per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"By default, this is the five minute
exponentially-decayed moving average of the
outbound octet rate for this interface.
However, if the corresponding instance of
cieIfInterval is instantiated with a value
which specifies an interval different from
5-minutes, then cieIfOutOctetRate is the
exponentially-decayed moving average of outbound
octet rate over this different time interval."
::= { cieIfUtilEntry 4 }
cieIfInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the time interval over which
the inbound and outbound traffic rates are
calculated for this interface."
::= { cieIfUtilEntry 5 }
-- dot1BaseMapping Group
cieIfDot1dBaseMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfDot1dBaseMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the mappings of the
ifIndex of an interface to its
corresponding dot1dBasePort value."
REFERENCE "dot1dBasePort is defined in BRIDGE-MIB."
::= { ciscoIfExtDot1dBaseMapping 1 }
cieIfDot1dBaseMappingEntry OBJECT-TYPE
SYNTAX CieIfDot1dBaseMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing the mapping between
the ifIndex value of an interface and its
corresponding dot1dBasePort value.
Every interface which has been assigned
a dot1dBasePort value by the system
has a corresponding entry in this table."
REFERENCE "dot1dBasePort is defined in BRIDGE-MIB."
INDEX { ifIndex }
::= { cieIfDot1dBaseMappingTable 1 }
CieIfDot1dBaseMappingEntry ::= SEQUENCE {
cieIfDot1dBaseMappingPort Integer32
}
cieIfDot1dBaseMappingPort OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dot1dBasePort value for this interface."
REFERENCE "dot1dBasePort is defined in BRIDGE-MIB."
::= { cieIfDot1dBaseMappingEntry 1 }
-- Cisco IF Extension 'ifName' to 'ifIndex' Mapping Table
cieIfNameMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF CieIfNameMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects for providing
the 'ifName' to 'ifIndex' mapping.
This table contains one entry for each
valid 'ifName' available in the system.
Upon the first request, the implementation
of this table will get all the available
ifNames, and it will populate the entries
in this table, it maintains this ifNames
in a cache for ~30 seconds."
::= { ciscoIfExtIfNameMapping 1 }
cieIfNameMappingEntry OBJECT-TYPE
SYNTAX CieIfNameMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry into the cieIfNameMappingTable."
INDEX { cieIfName }
::= { cieIfNameMappingTable 1 }
CieIfNameMappingEntry ::= SEQUENCE {
cieIfName DisplayString,
cieIfIndex InterfaceIndexOrZero
}
cieIfName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..112))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Represents an interface name mentioned
in the 'ifName' object of this system."
::= { cieIfNameMappingEntry 1 }
cieIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 'ifIndex'
corresponding to the interface name mentioned
in the 'cieIfName' object of this instance.
If the 'ifName' mentioned in the 'cieIfName'
object of this instance corresponds to multiple
'ifIndex' values, then the value of this object
is the numerically smallest of those multiple
'ifIndex' values."
::= { cieIfNameMappingEntry 2 }
-- definition of cisco specific interface-related traps.
cieLinkDown NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ifAdminStatus,
ifOperStatus,
ifName,
ifType
}
STATUS current
DESCRIPTION
"A cisco specific linkDown notification
signifies that the SNMP entity, acting in an
agent role, has detected that the ifOperStatus
object for one of its communication links is
about to enter the down state from some other
state (but not from the notPresent state).
The varbinds for this notification indicate the
interface information of the communication
link."
::= { ciscoIfExtensionMIBNotifications 1 }
cieLinkUp NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ifAdminStatus,
ifOperStatus,
ifName,
ifType
}
STATUS current
DESCRIPTION
"A cisco specific linkUp trap signifies that
the SNMP entity, acting in an agent role, has
detected that the ifOperStatus object for one
of its communication links left the down state
and transitioned into some other state (but not
into the notPresent state). The varbinds for
this notification indicate the interface
information of the communication link."
::= { ciscoIfExtensionMIBNotifications 2 }
cieDelayedLinkUpDownNotif NOTIFICATION-TYPE
OBJECTS {
ifAdminStatus,
ifOperStatus,
ifName,
ifType,
cieIfOperStatusCause
}
STATUS current
DESCRIPTION
"This notification indicates when an interface's operational
status has transitioned and remained in that state for a time
specified by cieDelayedLinkUpDownDelay."
::= { ciscoIfExtensionMIBNotifications 3 }
-- Conformance
ciscoIfExtensionMIBCompliances OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBConformance 1 }
ciscoIfExtensionMIBGroups OBJECT IDENTIFIER
::= { ciscoIfExtensionMIBConformance 2 }
-- Compliance
ciscoIfExtensionMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
MANDATORY-GROUPS {
ciscoIfExtensionTablePacketGroup,
ciscoIfExtensionTableIntfGroup
}
::= { ciscoIfExtensionMIBCompliances 1 }
ciscoIfExtensionMIBCompliance1 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup1
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only required
on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 2 }
ciscoIfExtensionMIBCompliance2 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup1
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only required
on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 3 }
ciscoIfExtensionMIBCompliance3 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup1
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only required
on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 4 }
ciscoIfExtensionMIBCompliance4 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only required
on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 5 }
ciscoIfExtensionMIBCompliance5 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 6 }
ciscoIfExtensionMIBCompliance6 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 7 }
ciscoIfExtensionMIBCompliance7 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 8 }
ciscoIfExtensionMIBCompliance8 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieIfIndexPersistenceGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 9 }
ciscoIfExtensionMIBCompliance9 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 10 }
ciscoIfExtensionMIBCompliance10 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup2
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 11 }
ciscoIfExtensionMIBCompliance11 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
GROUP ciscoIfExtensionTableIntfGroup3
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 12 }
ciscoIfExtensionMIBCompliance12 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
GROUP ciscoIfExtensionTableIntfGroup3
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroupSup1
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
::= { ciscoIfExtensionMIBCompliances 13 }
ciscoIfExtensionMIBCompliance13 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroupSup1
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfVlStatsGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3SupR01
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
OBJECT cieIfSpeedGroupConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
::= { ciscoIfExtensionMIBCompliances 14 }
ciscoIfExtensionMIBCompliance14 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroupSup1
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfVlStatsGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3SupR01
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifConfigGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
OBJECT cieIfSpeedGroupConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
::= { ciscoIfExtensionMIBCompliances 15 }
ciscoIfExtensionMIBCompliance15 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which
implement the CISCO-IF-EXTENSION-MIB."
MODULE -- this module
GROUP ciscoIfExtensionTablePacketGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionSystemGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1qEtherTypeGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilizationGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtDot1dBaseMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtIfNameMappingGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionAsymmetricalSpeedGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtUtilIntervalGroup
DESCRIPTION
"Implementation of this group is mandatory for those
platforms which provide the information of calculation
interval for utilization rate on interfaces."
GROUP cieDelayedLinkUpDownNotifNotifGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieDelayedLinkUpDownNotifNotifEnableGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfIndexPersistenceControlGroup
DESCRIPTION
"Implementation of this group is mandatory for those
interfaces which support ifIndex Persistence."
GROUP cieIfStatusListGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfStatusListGroupSup1
DESCRIPTION
"Implementation of this group is optional."
GROUP cieIfVlStatsGroup
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3SupR01
DESCRIPTION
"Implementation of this group is optional."
GROUP ciscoIfExtensionTableIntfGroup3SupR02
DESCRIPTION
"Implementation of this group is optional."
GROUP cieLinkUpDownNotifConfigGroup
DESCRIPTION
"Implementation of this group is optional."
OBJECT cieIfDhcpMode
SYNTAX INTEGER {
false(2)
}
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only. Support for 'true' is only
required on interfaces which support DHCP."
OBJECT cieIfMtu
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as
read-only."
OBJECT cieIfSpeedGroupConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
OBJECT cieIfTransceiverFrequencyConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
OBJECT cieIfFillPatternConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
OBJECT cieIfIgnoreBitErrorsConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
OBJECT cieIfIgnoreInterruptThresholdConfig
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional."
::= { ciscoIfExtensionMIBCompliances 16 }
ciscoIfExtensionTablePacketGroup OBJECT-GROUP
OBJECTS {
cieIfLastInTime,
cieIfLastOutTime,
cieIfLastOutHangTime,
cieIfInRuntsErrs,
cieIfInGiantsErrs,
cieIfInFramingErrs,
cieIfInOverrunErrs,
cieIfInIgnored,
cieIfInAbortErrs,
cieIfInputQueueDrops,
cieIfOutputQueueDrops,
cieIfPacketDiscontinuityTime
}
STATUS current
DESCRIPTION
"A collection of objects containing packet
statistics for a given interface."
::= { ciscoIfExtensionMIBGroups 1 }
ciscoIfExtensionTableIntfGroup OBJECT-GROUP
OBJECTS {
cieIfResetCount,
cieIfKeepAliveEnabled,
cieIfStateChangeReason,
cieIfCarrierTransitionCount,
cieIfInterfaceDiscontinuityTime
}
STATUS current
DESCRIPTION
"A collection of objects containing
information about properties of
interfaces."
::= { ciscoIfExtensionMIBGroups 2 }
ciscoIfExtensionTableIntfGroup1 OBJECT-GROUP
OBJECTS {
cieIfDhcpMode,
cieIfMtu,
cieIfContextName
}
STATUS deprecated
DESCRIPTION
"A collection of objects containing
information about properties of
interfaces."
::= { ciscoIfExtensionMIBGroups 3 }
ciscoIfExtensionSystemGroup OBJECT-GROUP
OBJECTS { cieSystemMtu }
STATUS current
DESCRIPTION
"A collection of objects providing
global system-wise information about
interfaces."
::= { ciscoIfExtensionMIBGroups 4 }
ciscoIfExtDot1qEtherTypeGroup OBJECT-GROUP
OBJECTS {
cieIfDot1qCustomAdminEtherType,
cieIfDot1qCustomOperEtherType
}
STATUS current
DESCRIPTION
"A collection of objects providing
the information about 802.1q
custom EtherType on the
interface."
::= { ciscoIfExtensionMIBGroups 5 }
ciscoIfExtUtilizationGroup OBJECT-GROUP
OBJECTS {
cieIfInPktRate,
cieIfInOctetRate,
cieIfOutPktRate,
cieIfOutOctetRate
}
STATUS current
DESCRIPTION
"A collection of objects containing
information about utilization rates of
interfaces."
::= { ciscoIfExtensionMIBGroups 6 }
ciscoIfExtDot1dBaseMappingGroup OBJECT-GROUP
OBJECTS { cieIfDot1dBaseMappingPort }
STATUS current
DESCRIPTION
"A collection of objects containing
mapping information about the ifIndex values
of interfaces and their dot1dBasePort
values."
::= { ciscoIfExtensionMIBGroups 7 }
ciscoIfExtIfNameMappingGroup OBJECT-GROUP
OBJECTS { cieIfIndex }
STATUS current
DESCRIPTION
"A collection of objects for the
'ifName' to 'ifIndex' mapping."
::= { ciscoIfExtensionMIBGroups 8 }
ciscoIfExtensionTableIntfGroup2 OBJECT-GROUP
OBJECTS {
cieIfDhcpMode,
cieIfMtu,
cieIfContextName,
cieIfOperStatusCause,
cieIfOperStatusCauseDescr
}
STATUS deprecated
DESCRIPTION
"A collection of objects containing
information about properties of
interfaces."
::= { ciscoIfExtensionMIBGroups 9 }
cieIfStatusListGroup OBJECT-GROUP
OBJECTS {
cieInterfacesIndex,
cieInterfacesOperMode,
cieInterfacesOperCause
}
STATUS current
DESCRIPTION
"A collection of objects containing
information about set of interfaces."
::= { ciscoIfExtensionMIBGroups 10 }
cieLinkUpDownNotifEnableGroup OBJECT-GROUP
OBJECTS {
cieLinkUpDownEnable,
cieStandardLinkUpDownVarbinds
}
STATUS deprecated
DESCRIPTION
"A collection of objects to control
'cieLinkUp/cieLinkDown' and standard mib-II
defined 'linkUp/linkDown' notifications."
::= { ciscoIfExtensionMIBGroups 11 }
cieLinkUpDownNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS {
cieLinkDown,
cieLinkUp
}
STATUS current
DESCRIPTION
"A collection of cisco specific linkUp and
linkDown notifications."
::= { ciscoIfExtensionMIBGroups 12 }
ciscoIfExtensionAsymmetricalSpeedGroup OBJECT-GROUP
OBJECTS {
cieIfSpeedReceive,
cieIfHighSpeedReceive
}
STATUS current
DESCRIPTION
"An optional group used to provide information on asymmetrical
interface speeds."
::= { ciscoIfExtensionMIBGroups 13 }
ciscoIfExtUtilIntervalGroup OBJECT-GROUP
OBJECTS { cieIfInterval }
STATUS current
DESCRIPTION
"A collection of objects containing
information about calculation interval for
utilization rate on interfaces."
::= { ciscoIfExtensionMIBGroups 14 }
cieIfIndexPersistenceGroup OBJECT-GROUP
OBJECTS {
cieIfIndexPersistence,
cieIfIndexPersistenceEnabled
}
STATUS deprecated
DESCRIPTION
"A collection of objects containing information about ifIndex
Persistence of interfaces.
Since cieIfIndexPersistence and cieIfIndexPersistenceEnabled are
deprecated, so, cieIfIndexPersistenceGroup containing these two
objects are deprecated by cieIfIndexPersistenceControlGroup."
::= { ciscoIfExtensionMIBGroups 15 }
cieDelayedLinkUpDownNotifNotifEnableGroup OBJECT-GROUP
OBJECTS {
cieDelayedLinkUpDownNotifEnable,
cieDelayedLinkUpDownNotifDelay
}
STATUS current
DESCRIPTION
"The group of objects that help configure the
cieDelayedLinkUpDownNotif on the system."
::= { ciscoIfExtensionMIBGroups 16 }
cieDelayedLinkUpDownNotifNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS { cieDelayedLinkUpDownNotif }
STATUS current
DESCRIPTION
"A collection for cisco specific delayed trap notifications."
::= { ciscoIfExtensionMIBGroups 17 }
cieIfIndexPersistenceControlGroup OBJECT-GROUP
OBJECTS {
cieIfIndexGlobalPersistence,
cieIfIndexPersistenceControl
}
STATUS current
DESCRIPTION
"A collection of objects containing information about ifIndex
Persistence of interfaces."
::= { ciscoIfExtensionMIBGroups 18 }
ciscoIfExtensionTableIntfGroup3 OBJECT-GROUP
OBJECTS {
cieIfDhcpMode,
cieIfMtu,
cieIfContextName,
cieIfOperStatusCause,
cieIfOperStatusCauseDescr,
cieIfOwner
}
STATUS current
DESCRIPTION
"A collection of objects containing
information about properties of
interfaces."
::= { ciscoIfExtensionMIBGroups 19 }
cieIfStatusListGroupSup1 OBJECT-GROUP
OBJECTS { cieInterfaceOwnershipBitmap }
STATUS current
DESCRIPTION
"Additional objects containing information about a
set of interfaces."
::= { ciscoIfExtensionMIBGroups 20 }
cieIfVlStatsGroup OBJECT-GROUP
OBJECTS {
cieIfNoDropVlInPkts,
cieIfNoDropVlInOctets,
cieIfNoDropVlOutPkts,
cieIfNoDropVlOutOctets,
cieIfDropVlInPkts,
cieIfDropVlInOctets,
cieIfDropVlOutPkts,
cieIfDropVlOutOctets
}
STATUS current
DESCRIPTION
"Objects containing information about a
VL (Virtual Link) statistics on an interface."
::= { ciscoIfExtensionMIBGroups 21 }
ciscoIfExtensionTableIntfGroup3SupR01 OBJECT-GROUP
OBJECTS {
cieIfSharedConfig,
cieIfSpeedGroupConfig
}
STATUS current
DESCRIPTION
"This group is supplement to ciscoIfExtensionTableIntfGroup3."
::= { ciscoIfExtensionMIBGroups 22 }
cieLinkUpDownNotifConfigGroup OBJECT-GROUP
OBJECTS { cieLinkUpDownConfig }
STATUS current
DESCRIPTION
"A collection of objects to control
'cieLinkUp/cieLinkDown' and standard mib-II
defined 'linkUp/linkDown' notifications."
::= { ciscoIfExtensionMIBGroups 23 }
ciscoIfExtensionTableIntfGroup3SupR02 OBJECT-GROUP
OBJECTS {
cieIfTransceiverFrequencyConfig,
cieIfFillPatternConfig,
cieIfIgnoreBitErrorsConfig,
cieIfIgnoreInterruptThresholdConfig
}
STATUS current
DESCRIPTION
"This group is supplement to ciscoIfExtensionTableIntfGroup3SupR01."
::= { ciscoIfExtensionMIBGroups 24 }
END