david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
main
mibs/MIBS/cisco/CISCO-LWAPP-RF-MIB

1722 lines
63 KiB
Plaintext
Raw Permalink Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
-- *******************************************************************
-- CISCO-LWAPP-RF-MIB.my
-- This MIB helps to manage the RF parameters on the controller
-- June 2011, Srinath Candadai
--
-- Copyright (c) 2011, 2016-2018 by Cisco Systems, Inc.
-- All rights reserved.
-- *******************************************************************
CISCO-LWAPP-RF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Unsigned32,
Integer32
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION,
RowStatus,
TruthValue,
StorageType
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
CLApIfType
FROM CISCO-LWAPP-TC-MIB
cLAPGroupName
FROM CISCO-LWAPP-WLAN-MIB
ciscoMgmt
FROM CISCO-SMI;
ciscoLwappRFMIB MODULE-IDENTITY
LAST-UPDATED "201811150000Z"
ORGANIZATION "Cisco Systems Inc."
CONTACT-INFO
"Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
Email: cs-wnbu-snmp@cisco.com"
DESCRIPTION
"This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB helps to manage the Radio Frequency (RF)
parameters on the controller.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends it to the controller to which
it is logically connected to.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity also referred to as 'controller'.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
controllers.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point.
802.1x
The IEEE ratified standard for enforcing port based
access control. This was originally intended for
use on wired LANs and later extended for use in
802.11 WLAN environments. This defines an
architecture with three main parts - a supplicant
(Ex. an 802.11 wireless client), an authenticator
(the AP) and an authentication server(a Radius
server). The authenticator passes messages back
and forth between the supplicant and the
authentication server to enable the supplicant
get authenticated to the network.
Radio Frequency ( RF )
Radio frequency (RF) is a rate of oscillation in the
range of about 3 kHz to 300 GHz, which corresponds to
the frequency of radio waves, and the
alternating currents which carry radio signals.
Received Signal Strength Indicator ( RSSI )
A measure of the strength of the signal as
observed by the entity that received it,
expressed in 'dbm'.
Coverage Hole Detection ( CHD )
If clients on an Access Point are detected at low
RSSI levels, it is considered a coverage hole
by the Access Points. This indicates the existence
of an area where clients are continually getting poor
signal coverage, without having a viable location to
roam to.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol
[3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s,
2.4 GHz RF and IR standard."
REVISION "201811150000Z"
DESCRIPTION
"Added below object to the cLRFProfileTable
- cLRFProfileAirTimeAllocation
- cLRFProfileAirTimeFairnessMode
- cLRFProfileAirTimeFairnessOptimization
- cLRFProfileUnusedChannelList
- cLRFProfileShutdown
- cLRFProfileBridgeClientAccess
- cLRFProfileRxSopThresholdCustom
Modified below object of cLRFProfileTable
- cLRFProfileRxSopThreshold
Added new table cLRFProfileRemoveChannelTable
and cLRFProfileAddChannelTable"
REVISION "201707070000Z"
DESCRIPTION
"Added new table cLRFProfileChannelListTable."
REVISION "201204270000Z"
DESCRIPTION
"Add 11n MCS rates support in profile,
cLRFProfileMcsDataRateTable is added for
this rate setting."
REVISION "201201270000Z"
DESCRIPTION
"Below new objects have been added to the cLRFProfileTable
cLRFProfileHighDensityMaxRadioClients
cLRFProfileBandSelectProbeResponse
cLRFProfileBandSelectCycleCount
cLRFProfileBandSelectCycleThreshold
cLRFProfileBandSelectExpireSuppression
cLRFProfileBandSelectExpireDualBand
cLRFProfileBandSelectClientRSSI
cLRFProfileLoadBalancingWindowSize
cLRFProfileCHDDataRSSIThreshold
cLRFProfileCHDVoiceRSSIThreshold
cLRFProfileCHDClientExceptionLevel
cLRFProfileCHDCoverageExceptionLevel
cLRFProfileMulticastDataRate
cLRFProfileBandSelectClientMidRSSI
cLRFProfileClientNetworkPreference
One new scalar object has been added
cLRFProfileOutOfBoxAPConfig
cLRFProfileOutOfBoxAPPersistenceConfig"
REVISION "201111010000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 778 }
ciscoLwappRFMIBNotifs OBJECT IDENTIFIER
::= { ciscoLwappRFMIB 0 }
ciscoLwappRFMIBObjects OBJECT IDENTIFIER
::= { ciscoLwappRFMIB 1 }
ciscoLwappRFMIBConform OBJECT IDENTIFIER
::= { ciscoLwappRFMIB 2 }
ciscoLwappRFConfig OBJECT IDENTIFIER
::= { ciscoLwappRFMIBObjects 1 }
ciscoLwappRFGlobalObjects OBJECT IDENTIFIER
::= { ciscoLwappRFMIBObjects 2 }
CiscoLwappRFApDataRates ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This field indicates the data rates supported by an AP
'disabled'
The rate is not supported by the AP
'supported'
The rate is supported by the AP
'mandatoryRate'
The rate is required by the AP
'notApplicable'
The rate is notApplicable."
SYNTAX INTEGER {
disabled(0),
supported(1),
mandatoryRate(2),
notApplicable(3)
}
-- ********************************************************************
-- * AP Groups RF Profile
-- ********************************************************************
cLAPGroupsRFProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLAPGroupsRFProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists the mapping between an RF profile
and an AP group."
::= { ciscoLwappRFConfig 1 }
cLAPGroupsRFProfileEntry OBJECT-TYPE
SYNTAX CLAPGroupsRFProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing the configuration attributes
that affect the operation of the APs within
a group.
Entries can be added/deleted by explicit management
action from NMS/EMS through the 'bsnAPGroupsVlanRowStatus'
object in bsnAPGroupsVlanTable as defined by the
AIRESPACE-WIRELESS-MIB."
INDEX { cLAPGroupName }
::= { cLAPGroupsRFProfileTable 1 }
CLAPGroupsRFProfileEntry ::= SEQUENCE {
cLAPGroups802dot11bgRFProfileName SnmpAdminString,
cLAPGroups802dot11aRFProfileName SnmpAdminString
}
cLAPGroups802dot11bgRFProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the RF profile name assigned to this
site on the 802.11bg radio. This profile being assigned should
exist in the 'cLRFProfileTable'. To disassociate a profile with
this site a string of zero length should be set."
::= { cLAPGroupsRFProfileEntry 1 }
cLAPGroups802dot11aRFProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the RF profile name assigned to this
site on the 802.11a radio. This profile being assigned should
exist in the 'cLRFProfileTable'. To disassociate a profile with
this site a string of zero length should be set."
::= { cLAPGroupsRFProfileEntry 2 }
-- ********************************************************************
-- * RF Profile Table
-- ********************************************************************
cLRFProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLRFProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists the configuration for each
RF profile."
::= { ciscoLwappRFConfig 2 }
cLRFProfileEntry OBJECT-TYPE
SYNTAX CLRFProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing the configuration attributes
that affect the operation of 802.11 RF domain.
Entries can be added/deleted by explicit management
action from NMS/EMS or through user console."
INDEX { cLRFProfileName }
::= { cLRFProfileTable 1 }
CLRFProfileEntry ::= SEQUENCE {
cLRFProfileName SnmpAdminString,
cLRFProfileDescr SnmpAdminString,
cLRFProfileTransmitPowerMin Integer32,
cLRFProfileTransmitPowerMax Integer32,
cLRFProfileTransmitPowerThresholdV1 Integer32,
cLRFProfileTransmitPowerThresholdV2 Integer32,
cLRFProfileDataRate1Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate2Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate5AndHalfMbps CiscoLwappRFApDataRates,
cLRFProfileDataRate11Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate6Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate9Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate12Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate18Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate24Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate36Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate48Mbps CiscoLwappRFApDataRates,
cLRFProfileDataRate54Mbps CiscoLwappRFApDataRates,
cLRFProfileRadioType CLApIfType,
cLRFProfileStorageType StorageType,
cLRFProfileRowStatus RowStatus,
cLRFProfileHighDensityMaxRadioClients Unsigned32,
cLRFProfileBandSelectProbeResponse TruthValue,
cLRFProfileBandSelectCycleCount Unsigned32,
cLRFProfileBandSelectCycleThreshold Unsigned32,
cLRFProfileBandSelectExpireSuppression Unsigned32,
cLRFProfileBandSelectExpireDualBand Unsigned32,
cLRFProfileBandSelectClientRSSI Integer32,
cLRFProfileLoadBalancingWindowSize Unsigned32,
cLRFProfileLoadBalancingMaxDenialCount Unsigned32,
cLRFProfileCHDDataRSSIThreshold Integer32,
cLRFProfileCHDVoiceRSSIThreshold Integer32,
cLRFProfileCHDClientExceptionLevel Unsigned32,
cLRFProfileCHDCoverageExceptionLevel Unsigned32,
cLRFProfileMulticastDataRate Unsigned32,
cLRFProfile11nOnly TruthValue,
cLRFProfileHDClientTrapThreshold Unsigned32,
cLRFProfileInterferenceThreshold Unsigned32,
cLRFProfileNoiseThreshold Integer32,
cLRFProfileUtilizationThreshold Unsigned32,
cLRFProfileDCAForeignContribution TruthValue,
cLRFProfileDCAChannelWidth INTEGER,
cLRFProfileDCAChannelList SnmpAdminString,
cLRFProfileRxSopThreshold INTEGER,
cLRFProfileHSRMode TruthValue,
cLRFProfileHSRNeighborTimeoutFactor Unsigned32,
cLRFProfileBandSelectClientMidRSSI Integer32,
cLRFProfileClientNetworkPreference INTEGER,
cLRFProfileUnusedChannelList SnmpAdminString,
cLRFProfileShutdown TruthValue,
cLRFProfileAirTimeFairnessMode INTEGER,
cLRFProfileAirTimeFairnessOptimization INTEGER,
cLRFProfileBridgeClientAccess TruthValue,
cLRFProfileAirTimeAllocation Unsigned32,
cLRFProfileRxSopThresholdCustom Integer32
}
cLRFProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a RF Profile."
::= { cLRFProfileEntry 1 }
cLRFProfileDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a human-readable description of the
profile."
::= { cLRFProfileEntry 2 }
cLRFProfileTransmitPowerMin OBJECT-TYPE
SYNTAX Integer32 (-10..30)
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the lower bound of transmit
power value supported by an AP."
DEFVAL { -10 }
::= { cLRFProfileEntry 3 }
cLRFProfileTransmitPowerMax OBJECT-TYPE
SYNTAX Integer32 (-10..30)
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the uppoer bound of transmit
power value supported by an AP."
DEFVAL { 30 }
::= { cLRFProfileEntry 4 }
cLRFProfileTransmitPowerThresholdV1 OBJECT-TYPE
SYNTAX Integer32 (-80..-50)
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the transmit power control
version 1 threshold for the radio resource management
algorithm."
DEFVAL { -70 }
::= { cLRFProfileEntry 5 }
cLRFProfileTransmitPowerThresholdV2 OBJECT-TYPE
SYNTAX Integer32 (-80..-50)
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the transmit power control
version 2 threshold for the radio resource management
algorithm."
DEFVAL { -67 }
::= { cLRFProfileEntry 6 }
cLRFProfileDataRate1Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { mandatoryRate }
::= { cLRFProfileEntry 7 }
cLRFProfileDataRate2Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { mandatoryRate }
::= { cLRFProfileEntry 8 }
cLRFProfileDataRate5AndHalfMbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { mandatoryRate }
::= { cLRFProfileEntry 9 }
cLRFProfileDataRate11Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { mandatoryRate }
::= { cLRFProfileEntry 10 }
cLRFProfileDataRate6Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 11 }
cLRFProfileDataRate9Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 12 }
cLRFProfileDataRate12Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 13 }
cLRFProfileDataRate18Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 14 }
cLRFProfileDataRate24Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 15 }
cLRFProfileDataRate36Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 16 }
cLRFProfileDataRate48Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 17 }
cLRFProfileDataRate54Mbps OBJECT-TYPE
SYNTAX CiscoLwappRFApDataRates
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the configuration for this
data rate."
DEFVAL { supported }
::= { cLRFProfileEntry 18 }
cLRFProfileRadioType OBJECT-TYPE
SYNTAX CLApIfType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to configure the radio
type for this profile."
::= { cLRFProfileEntry 19 }
cLRFProfileStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object represents the storage type for this
conceptual row."
DEFVAL { nonVolatile }
::= { cLRFProfileEntry 20 }
cLRFProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and used
to create and delete specific instances of rows
in this table."
::= { cLRFProfileEntry 21 }
cLRFProfileHighDensityMaxRadioClients OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the maximum number
of clients per AP radio in high density environment."
DEFVAL { 200 }
::= { cLRFProfileEntry 22 }
cLRFProfileBandSelectProbeResponse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the AP's probe response
with clients to verify whether client can associate
on both 2.4 GHz and 5Ghz spectrum.
When set to true, AP suppresses probe response
to new clients for all SSIDs that are not being
Band Select disabled."
DEFVAL { false }
::= { cLRFProfileEntry 23 }
cLRFProfileBandSelectCycleCount OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies number of times a client probe (2.4 G-Hz)
is suppressed before the AP starts responding to the probes."
DEFVAL { 2 }
::= { cLRFProfileEntry 24 }
cLRFProfileBandSelectCycleThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies time threshold for a new scanning
mobile station period. Mobile station cycle counter will
increment only if mobile station scans same channel any
time after threshold is passed."
DEFVAL { 200 }
::= { cLRFProfileEntry 25 }
cLRFProfileBandSelectExpireSuppression OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the duration at which
an AP waits to conduct another probe suppression."
DEFVAL { 20 }
::= { cLRFProfileEntry 26 }
cLRFProfileBandSelectExpireDualBand OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the timeout duration until
which an AP should not respond to 2.4ghz probe requests
from a dual-band client. Once this band select duration
expires the client will be marked as a non-dual band client
and AP will start responding to the 2.4 Ghz probes."
DEFVAL { 60 }
::= { cLRFProfileEntry 27 }
cLRFProfileBandSelectClientRSSI OBJECT-TYPE
SYNTAX Integer32
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies minimum mobile station RSSI threshold.
Mobile stations having RSSI below this value will not be
recorded in the suppressed table.
This configuration filters out far away mobile stations with
weaker signal strength. This will limit the number of
mobile stations on the table to a reasonable amount."
DEFVAL { -80 }
::= { cLRFProfileEntry 28 }
cLRFProfileLoadBalancingWindowSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum number of clients
to be associated on an AP in order to trigger load balancing."
DEFVAL { 5 }
::= { cLRFProfileEntry 29 }
cLRFProfileLoadBalancingMaxDenialCount OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies maximum number of association
rejections sent by AP to a mobile station for a given sequence
of association.
When a mobile station tries to associate on wireless network, it
sends association request to AP. If AP is overloaded and
load balancing is enable on controller, AP will send a
denial to association request. If there are no other AP
in the vicinity of mobile station, it will try to associate same
AP again. So to restrict the number of denial sent from
AP, cldLoadBalancingMaxDenialCount is defined. After maximum
denial count is reached mobile station will be able to
associate."
DEFVAL { 3 }
::= { cLRFProfileEntry 30 }
cLRFProfileCHDDataRSSIThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the RSSI value for non-voice clients
i.e., clients sending only data traffic
to trigger coverage event."
DEFVAL { -80 }
::= { cLRFProfileEntry 31 }
cLRFProfileCHDVoiceRSSIThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the RSSI value for voice
clients to trigger coverage event."
DEFVAL { -80 }
::= { cLRFProfileEntry 32 }
cLRFProfileCHDClientExceptionLevel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum
number of clients required to trigger
coverage hole."
DEFVAL { 3 }
::= { cLRFProfileEntry 33 }
cLRFProfileCHDCoverageExceptionLevel OBJECT-TYPE
SYNTAX Unsigned32
UNITS "%"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum
percentage of clients in the coverage hole region
of the AP, required to trigger a
coverage hole exception"
DEFVAL { 25 }
::= { cLRFProfileEntry 34 }
cLRFProfileMulticastDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Mbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the minimum
data rate at which multicast clients
can associate to AP.
A value 0 indicates that AP will automatically
adjust data rates."
DEFVAL { 0 }
::= { cLRFProfileEntry 35 }
cLRFProfile11nOnly OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if 11n-client-only mode is
enabled.
A value of 'true' indicates 11n-client-only mode
enabled.
A value of 'false' indicates 11n-client-only mode
disabled."
DEFVAL { false }
::= { cLRFProfileEntry 36 }
cLRFProfileHDClientTrapThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the threshold number
of clients per AP radio to trigger a trap.
The trap ciscoLwappApClientThresholdNotify
will be triggered once the count of clients
on the AP radio reaches this limit. A value
of zero indicates that the trap is disabled."
::= { cLRFProfileEntry 37 }
cLRFProfileInterferenceThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies interference threshold in %
traps are generated when interference exceeds this value ."
::= { cLRFProfileEntry 38 }
cLRFProfileNoiseThreshold OBJECT-TYPE
SYNTAX Integer32 (-127..0)
UNITS "dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the threshold number
of noise threshold between -127 and 0 dBm."
::= { cLRFProfileEntry 39 }
cLRFProfileUtilizationThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the threshold of bandwidth (%)
being utilized by an access-point.
Traps are sent when this value is exceeded"
::= { cLRFProfileEntry 40 }
cLRFProfileDCAForeignContribution OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether foreign interference
is taken into account for the DCA metrics.
A value of 'true' indicates that foreign interference is
is considered when DCA metrics is derived. A value of 'false'
indicates foreign interference is not taken into account
when deriving the DCA metrics."
::= { cLRFProfileEntry 41 }
cLRFProfileDCAChannelWidth OBJECT-TYPE
SYNTAX INTEGER {
twenty(1),
forty(2),
eighty(3),
onesixty(4),
best(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies how the system performs DCA
channel width selection for the RFProfile
twenty - 20MHz channel width supported by
this radio.
forty - 40MHz channel width supported by this radio.
eighty - 80MHz channel width supported by this radio.
onesixty - 160MHz channel width supported by this radio.
best - Dynamic channel width(160MHz, 80MHz, 40MHz or 20MHz) supported by this radio."
::= { cLRFProfileEntry 42 }
cLRFProfileDCAChannelList OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..500))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11 channels available to the
RF Profile. A comma separated list of integers."
::= { cLRFProfileEntry 43 }
cLRFProfileRxSopThreshold OBJECT-TYPE
SYNTAX INTEGER {
auto(0),
low(1),
medium(2),
high(3),
custom(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the receiver start of packet threshold
for the rf profile.
auto - Reverts radio receiver SOP to auto.
high - Sets radio receiver SOP to high.
low - Sets radio receiver SOP to low.
medium - Sets radio receiver SOP to medium.
custom - Sets radio receiver SOP to Custom value."
DEFVAL { auto }
::= { cLRFProfileEntry 44 }
cLRFProfileHSRMode OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether HSR mode
for RF profile is enabled or not.
A value of 'true' indicates that HSR is enabled.
A value of 'false' indicates that HSR is disabled."
::= { cLRFProfileEntry 45 }
cLRFProfileHSRNeighborTimeoutFactor OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the timeout interval
of neighbors that will be configured for RF profile.
Neighbor timeout factor will be five times the neighbor interval"
::= { cLRFProfileEntry 46 }
cLRFProfileBandSelectClientMidRSSI OBJECT-TYPE
SYNTAX Integer32
UNITS "dbm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies medium mobile station RSSI threshold.
Mobile station between this value and cldBandSelectClientRssi
will be recorded in suppressed table but will not be denied.
The mobile station having RSSI stronger than this value will be recorded
and denied."
DEFVAL { -80 }
::= { cLRFProfileEntry 47 }
cLRFProfileClientNetworkPreference OBJECT-TYPE
SYNTAX INTEGER {
default(0),
connectivity(1),
throughput(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object represents the client network preference.
default(0) - RRM Algorithm has no preference on the clients.
connectivity(1) - RRM Algorithm has a preference on connectiviry of the clients.
throughput(2) - RRM Algorithm has a preference on high thoughput of the clients."
DEFVAL { default }
::= { cLRFProfileEntry 48 }
cLRFProfileUnusedChannelList OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..500))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the 802.11 channels present in ths un-used
channel list of RF Profile. A comma separated list of integers."
::= {cLRFProfileEntry 49 }
cLRFProfileShutdown OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies if rf profile is
disabled."
DEFVAL {true}
::= { cLRFProfileEntry 50 }
cLRFProfileAirTimeFairnessMode OBJECT-TYPE
SYNTAX INTEGER {
disable(1),
ssid(2),
monitor(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the mode of fairness for ATF
supported APs, joined to the controller.
disable(1) - This indicates that fairness mode is
disabled.
SSID Mode(2) - This indicates that fairness mode is SSID
mode.
Monitor Mode(3) - This indicates that fairness mode is
monitor mode."
DEFVAL { 1 }
::= { cLRFProfileEntry 51 }
cLRFProfileAirTimeFairnessOptimization OBJECT-TYPE
SYNTAX INTEGER {
disable(1),
enable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the optimization for ATF
supported APs, joined to the controller to be
configured."
DEFVAL { 1 }
::= { cLRFProfileEntry 52 }
cLRFProfileBridgeClientAccess OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether airtime
allocation is enabled for the client access node."
DEFVAL { false }
::= {cLRFProfileEntry 53 }
cLRFProfileAirTimeAllocation OBJECT-TYPE
SYNTAX Unsigned32(5..90)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the percentage for airtime
allocation for the client access node."
DEFVAL { 5 }
::= {cLRFProfileEntry 54 }
cLRFProfileRxSopThresholdCustom OBJECT-TYPE
SYNTAX Integer32(-85..-60)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the percentage for the receiver
start of packet custom threshold for the client access node."
DEFVAL { -85 }
::= {cLRFProfileEntry 55 }
-- *******************************************************************
-- * Out of Box AP config
-- *******************************************************************
cLRFProfileOutOfBoxAPConfig OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the out of box AP config feature.
Enabling this feature will allow any AP that does not have
group name configured upon join to controller then
it will be considered as out of box AP and it will be
moved to a special AP Group. Disabling this feature
will only stop further subscription of new AP's to
Out of Box AP group. A value of 'true' indicates that
out of box AP feature is enabled and APs will be moved
to newly created AP group out-of-box and shut of their
radios. A value of 'false' indicates that out of box AP
feature is disabled."
::= { ciscoLwappRFGlobalObjects 1 }
cLRFProfileOutOfBoxAPPersistenceConfig OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the
out of box AP group to be persistent or not.
A value of 'true' indicates out-of-box persistence need to be
enabled.
A value of 'false' indicates out-of-box persistence need to be
disabled."
::= { ciscoLwappRFGlobalObjects 2 }
cLRFProfileMcsDataRateTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLRFProfileMcsDataRateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the 11n MCS rates supported by
the RF profile, indexed by the MCS rate, ranging from 1
to 32, corresponding to rate MCS-0, MCS-1, ... MCS-31."
::= { ciscoLwappRFConfig 3 }
cLRFProfileMcsDataRateEntry OBJECT-TYPE
SYNTAX CLRFProfileMcsDataRateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing MCS date rate information applicable
to a particular profile. Entry is added to the table when
the data rate is set to 'supported' or 'mandatory'."
INDEX {
cLRFProfileMcsName,
cLRFProfileMcsRate
}
::= { cLRFProfileMcsDataRateTable 1 }
CLRFProfileMcsDataRateEntry ::= SEQUENCE {
cLRFProfileMcsName SnmpAdminString,
cLRFProfileMcsRate Unsigned32,
cLRFProfileMcsRateSupport TruthValue
}
cLRFProfileMcsName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a RF Profile."
::= { cLRFProfileMcsDataRateEntry 1 }
cLRFProfileMcsRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the MCS data rate
for a particular profile."
::= { cLRFProfileMcsDataRateEntry 2 }
cLRFProfileMcsRateSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable the data
rate.
A value of 'true' indicates MCS support is enabled.
A value of 'false' indicates MCS support is disabled."
DEFVAL { true }
::= { cLRFProfileMcsDataRateEntry 3 }
cLRFProfileChannelListTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLRFProfileChannelListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the list of channels that is available for DCA
of a RF profile."
::= { ciscoLwappRFConfig 4 }
cLRFProfileChannelListEntry OBJECT-TYPE
SYNTAX CLRFProfileChannelListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing Channel List information applicable
to a particular profile."
INDEX {
cLRFProfileName,
cLRFProfileChanNumber
}
::= { cLRFProfileChannelListTable 1 }
CLRFProfileChannelListEntry ::= SEQUENCE {
cLRFProfileChanNumber Unsigned32,
cLRFProfileChanAddRemove INTEGER,
cLRFProfileChanRowStatus RowStatus
}
cLRFProfileChanNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the channel
for a particular profile."
::= { cLRFProfileChannelListEntry 1 }
cLRFProfileChanAddRemove OBJECT-TYPE
SYNTAX INTEGER {
add(1),
remove(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a channel is to be added
or removed from DCA list of the RFProfile.
add - Add the channel to global DCA channel list.
remove - Removed the channel from global DCA channel list."
::= { cLRFProfileChannelListEntry 2 }
cLRFProfileChanRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and used
to create and delete specific instances of rows
in this table."
::= { cLRFProfileChannelListEntry 3 }
cLRFProfileRemoveChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLRFProfileRemoveChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the removed channel information
from default DCA channel list for an AP's 802.11
interface using the RF profile.
Based on the country that an AP operates in, it
gets assigned to a regulatory domain. For a given
regulatory domain a fixed number of channels are
assigned automatically to an AP for a given interface.
We can remove a channel from this default list and
those channels will be put in this table.
This table represents the removed DCA channels information.
By default, there will not be any entries in this table.
An entry can be created or deleted from this table
using cLRFProfileRemoveChannelRowStatus."
::= { ciscoLwappRFConfig 5 }
cLRFProfileRemoveChannelEntry OBJECT-TYPE
SYNTAX CLRFProfileRemoveChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table provides the
removed channel information from the
default DCA channel list for this RF profile"
INDEX {
cLRFProfileRemoveChannelName,
cLRFProfileRemoveChannelNum
}
::= { cLRFProfileRemoveChannelTable 1 }
CLRFProfileRemoveChannelEntry ::= SEQUENCE {
cLRFProfileRemoveChannelName SnmpAdminString,
cLRFProfileRemoveChannelNum Unsigned32,
cLRFProfileRemovedChannelDcaState TruthValue,
cLRFProfileRemoveChannelRowStatus RowStatus
}
cLRFProfileRemoveChannelName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a RF Profile."
::= { cLRFProfileRemoveChannelEntry 1 }
cLRFProfileRemoveChannelNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The channel nubmer for this entry. This value
represents the unique channel number removed from
default DCA channel list for this RF profile."
::= { cLRFProfileRemoveChannelEntry 2 }
cLRFProfileRemovedChannelDcaState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether this channel is part
of the dynamic channel allocation (DCA) Remove List.
A value of 'false' indicates that the DCA for this
channel is disabled."
DEFVAL { false }
::= { cLRFProfileRemoveChannelEntry 3 }
cLRFProfileRemoveChannelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row.
All writable objects in this row may be modified
at any time."
::= { cLRFProfileRemoveChannelEntry 4 }
cLRFProfileAddChannelTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLRFProfileAddChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the added channel information
to the default DCA channel list in this RF profile.
Based on the country that an AP operates in, it
gets assigned to a regulatory domain. For a given
regulatory domain a fixed number of channels are
assigned automatically to an AP for a given interface.
We can add a channel to this default list and those
channels will be put in this table.
This table represents the added channels information
to the default DCA channel list.
By default, there will not be any entries in this table.
An entry can be created or deleted from this table
using cLRFProfileAddChannelRowStatus."
::= { ciscoLwappRFConfig 6 }
cLRFProfileAddChannelEntry OBJECT-TYPE
SYNTAX CLRFProfileAddChannelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table provides the
added channel information to the default
DCA channel list in this RF profile."
INDEX {
cLRFProfileAddChannelName,
cLRFProfileAddChannelNum
}
::= { cLRFProfileAddChannelTable 1 }
CLRFProfileAddChannelEntry ::= SEQUENCE {
cLRFProfileAddChannelName SnmpAdminString,
cLRFProfileAddChannelNum Unsigned32,
cLRFProfileAddedChannelDcaState TruthValue,
cLRFProfileAddChannelRowStatus RowStatus
}
cLRFProfileAddChannelName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a RF Profile."
::= { cLRFProfileAddChannelEntry 1 }
cLRFProfileAddChannelNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The channel nubmer for this entry. This value represents
the unique channel number added to the default DCA list in
this RF profile."
::= { cLRFProfileAddChannelEntry 2 }
cLRFProfileAddedChannelDcaState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether this channel is part
of the dynamic channel allocation (DCA) Add List.
A value of 'true' indicates that the DCA for this
channel is enabled."
DEFVAL { true }
::= { cLRFProfileAddChannelEntry 3 }
cLRFProfileAddChannelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row.
All writable objects in this row may be modified
at any time."
::= { cLRFProfileAddChannelEntry 4 }
-- ********************************************************************
-- * Compliance statements
-- ********************************************************************
ciscoLwappRFMIBCompliances OBJECT IDENTIFIER
::= { ciscoLwappRFMIBConform 1 }
ciscoLwappRFMIBGroups OBJECT IDENTIFIER
::= { ciscoLwappRFMIBConform 2 }
ciscoLwappRFMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappRFMIB module.
This compliance is deprecated and replaced by
ciscoLwappRFMIBComplianceVer1 ."
MODULE -- this module
MANDATORY-GROUPS { ciscoLwappRFConfigGroup }
OBJECT cLRFProfileRowStatus
SYNTAX INTEGER {
active(1),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"An implementation is only required to support
three of the six enumerated values of the
RowStatus textual convention, specifically,
'active', 'createAndGo' and 'destroy'.
This compliance is deprecated and replaced
by ciscoLwappRFMIBComplianceVer1."
::= { ciscoLwappRFMIBCompliances 1 }
ciscoLwappRFMIBComplianceVer1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappRFMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappRFConfigGroup1,
ciscoLwappRFGlobalConfigGroup
}
OBJECT cLRFProfileRowStatus
SYNTAX INTEGER {
active(1),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"An implementation is only required to support
three of the six enumerated values of the
RowStatus textual convention, specifically,
'active', 'createAndGo' and 'destroy'."
::= { ciscoLwappRFMIBCompliances 2 }
ciscoLwappRFMIBComplianceVer2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappRFMIB module.
Added ciscoLwappRFConfigGroup2 to add object to raise
trap when client count exceeds threshold and
ciscoLwappRFConfigGroup3 to address DCA settings"
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappRFConfigGroup1,
ciscoLwappRFGlobalConfigGroup,
ciscoLwappRFConfigGroup3
}
::= { ciscoLwappRFMIBCompliances 3 }
ciscoLwappRFMIBComplianceRev3 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappRFMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappRFConfigGroupVer1,
ciscoLwappRFConfigGroup1,
ciscoLwappRFConfigGroup3,
ciscoLwappRFConfigGroup4,
ciscoLwappRFGroupTrapThresholdConfig,
ciscoLwappRFGroupChannelConfig,
ciscoLwappRFGlobalConfigGroup,
ciscoLwappRFConfigGroupExtension1
}
OBJECT cLRFProfileRowStatus
SYNTAX INTEGER {
active(1),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"An implementation is only required to support
three of the six enumerated values of the
RowStatus textual convention, specifically,
'active', 'createAndGo' and 'destroy'."
::= { ciscoLwappRFMIBCompliances 4 }
ciscoLwappRFMIBComplianceRev4 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappRFMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappRFConfigGroupVer1,
ciscoLwappRFConfigGroup1,
ciscoLwappRFConfigGroup3,
ciscoLwappRFConfigGroup4,
ciscoLwappRFGroupTrapThresholdConfig,
ciscoLwappRFGroupChannelConfig,
ciscoLwappRFGlobalConfigGroup,
ciscoLwappRFConfigGroupExtension1,
ciscoLwappRFConfigGroup5,
ciscoLwappRFConfigGroup6,
ciscoLwappRFConfigGroup7
}
OBJECT cLRFProfileRowStatus
SYNTAX INTEGER {
active(1),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"An implementation is only required to support
three of the six enumerated values of the
RowStatus textual convention, specifically,
'active', 'createAndGo' and 'destroy'."
::= { ciscoLwappRFMIBCompliances 5 }
-- ********************************************************************
-- * Units of conformance
-- ********************************************************************
ciscoLwappRFConfigGroup OBJECT-GROUP
OBJECTS {
cLAPGroups802dot11bgRFProfileName,
cLAPGroups802dot11aRFProfileName,
cLRFProfileDescr,
cLRFProfileTransmitPowerMin,
cLRFProfileTransmitPowerMax,
cLRFProfileTransmitPowerThresholdV1,
cLRFProfileTransmitPowerThresholdV2,
cLRFProfileDataRate1Mbps,
cLRFProfileDataRate2Mbps,
cLRFProfileDataRate5AndHalfMbps,
cLRFProfileDataRate11Mbps,
cLRFProfileDataRate6Mbps,
cLRFProfileDataRate9Mbps,
cLRFProfileDataRate12Mbps,
cLRFProfileDataRate18Mbps,
cLRFProfileDataRate24Mbps,
cLRFProfileDataRate36Mbps,
cLRFProfileDataRate48Mbps,
cLRFProfileDataRate54Mbps,
cLRFProfileRadioType,
cLRFProfileStorageType,
cLRFProfileRowStatus,
cLRFProfile11nOnly
}
STATUS deprecated
DESCRIPTION
"This collection of objects specifies the
configuration of RF parameters on the controller
to be passed to an LWAPP AP.This config group
ciscoLwappRFConfigGroup is deprecated and replaced
by ciscoLwappRFConfigGroupVer1"
::= { ciscoLwappRFMIBGroups 1 }
-- ********************************************************************
-- * Units of conformance
-- ********************************************************************
ciscoLwappRFConfigGroupVer1 OBJECT-GROUP
OBJECTS {
cLAPGroups802dot11bgRFProfileName,
cLAPGroups802dot11aRFProfileName,
cLRFProfileDescr,
cLRFProfileTransmitPowerMin,
cLRFProfileTransmitPowerMax,
cLRFProfileTransmitPowerThresholdV1,
cLRFProfileTransmitPowerThresholdV2,
cLRFProfileDataRate1Mbps,
cLRFProfileDataRate2Mbps,
cLRFProfileDataRate5AndHalfMbps,
cLRFProfileDataRate11Mbps,
cLRFProfileDataRate6Mbps,
cLRFProfileDataRate9Mbps,
cLRFProfileDataRate12Mbps,
cLRFProfileDataRate18Mbps,
cLRFProfileDataRate24Mbps,
cLRFProfileDataRate36Mbps,
cLRFProfileDataRate48Mbps,
cLRFProfileDataRate54Mbps,
cLRFProfileRadioType,
cLRFProfileStorageType,
cLRFProfileRowStatus,
cLRFProfile11nOnly,
cLRFProfileHSRMode,
cLRFProfileHSRNeighborTimeoutFactor,
cLRFProfileOutOfBoxAPPersistenceConfig,
cLRFProfileMcsRateSupport
}
STATUS current
DESCRIPTION
"This collection of objects specifies the
configuration of RF parameters on the controller
to be passed to an LWAPP AP."
::= { ciscoLwappRFMIBGroups 2 }
ciscoLwappRFConfigGroup1 OBJECT-GROUP
OBJECTS {
cLRFProfileHighDensityMaxRadioClients,
cLRFProfileBandSelectProbeResponse,
cLRFProfileBandSelectCycleCount,
cLRFProfileBandSelectCycleThreshold,
cLRFProfileBandSelectExpireSuppression,
cLRFProfileBandSelectExpireDualBand,
cLRFProfileBandSelectClientRSSI,
cLRFProfileLoadBalancingWindowSize,
cLRFProfileLoadBalancingMaxDenialCount,
cLRFProfileCHDDataRSSIThreshold,
cLRFProfileCHDVoiceRSSIThreshold,
cLRFProfileCHDClientExceptionLevel,
cLRFProfileCHDCoverageExceptionLevel,
cLRFProfileMulticastDataRate,
cLRFProfileBandSelectClientMidRSSI,
cLRFProfileClientNetworkPreference
}
STATUS current
DESCRIPTION
"This collection of objects specifies the
configuration of RF parameters on the controller
to be passed to an LWAPP AP."
::= { ciscoLwappRFMIBGroups 3 }
ciscoLwappRFGlobalConfigGroup OBJECT-GROUP
OBJECTS { cLRFProfileOutOfBoxAPConfig }
STATUS current
DESCRIPTION
"This is the RF global config parameter."
::= { ciscoLwappRFMIBGroups 4 }
ciscoLwappRFGroupTrapThresholdConfig OBJECT-GROUP
OBJECTS {
cLRFProfileHDClientTrapThreshold,
cLRFProfileInterferenceThreshold,
cLRFProfileNoiseThreshold,
cLRFProfileUtilizationThreshold
}
STATUS current
DESCRIPTION
"This object specifies the configuration of Trap
threshold to be configured on the interface of an LWAPP AP."
::= { ciscoLwappRFMIBGroups 5 }
ciscoLwappRFConfigGroup3 OBJECT-GROUP
OBJECTS {
cLRFProfileDCAForeignContribution,
cLRFProfileDCAChannelWidth,
cLRFProfileDCAChannelList
}
STATUS current
DESCRIPTION
"This object specifies the configuration DCA for
RF Profiles."
::= { ciscoLwappRFMIBGroups 6 }
ciscoLwappRFConfigGroup4 OBJECT-GROUP
OBJECTS {
cLRFProfileRxSopThreshold,
cLRFProfileRxSopThresholdCustom
}
STATUS current
DESCRIPTION
"This object specifies the receiver start of packet
threshold for RF Profiles."
::= { ciscoLwappRFMIBGroups 7 }
ciscoLwappRFGroupDCAChannelConfig OBJECT-GROUP
OBJECTS { cLRFProfileDCAChannelList }
STATUS deprecated
DESCRIPTION
"This object specifies the add and remove channels for RF Profiles."
::= { ciscoLwappRFMIBGroups 8 }
ciscoLwappRFGroupChannelConfig OBJECT-GROUP
OBJECTS {
cLRFProfileChanRowStatus,
cLRFProfileChanAddRemove
}
STATUS current
DESCRIPTION
"This object specifies the add and remove channels for RF Profiles."
::= { ciscoLwappRFMIBGroups 9 }
ciscoLwappRFConfigGroupExtension1 OBJECT-GROUP
OBJECTS { cLRFProfileClientNetworkPreference }
STATUS current
DESCRIPTION
"This object specifies the
configuration of RF parameters on the controller
to be passed to an LWAPP AP."
::= { ciscoLwappRFMIBGroups 10 }
ciscoLwappRFConfigGroup5 OBJECT-GROUP
OBJECTS {
cLRFProfileUnusedChannelList,
cLRFProfileShutdown
}
STATUS current
DESCRIPTION
"This object specifies the receiver start of packet
threshold for RF Profiles."
::= { ciscoLwappRFMIBGroups 11 }
ciscoLwappRFConfigGroup6 OBJECT-GROUP
OBJECTS {
cLRFProfileAirTimeFairnessMode,
cLRFProfileAirTimeFairnessOptimization,
cLRFProfileBridgeClientAccess,
cLRFProfileAirTimeAllocation
}
STATUS current
DESCRIPTION
"This collection of object specifies the configuration
of AirTime Fairness parameters."
::= { ciscoLwappRFMIBGroups 12 }
ciscoLwappRFConfigGroup7 OBJECT-GROUP
OBJECTS {
cLRFProfileRemovedChannelDcaState,
cLRFProfileRemoveChannelRowStatus,
cLRFProfileAddedChannelDcaState,
cLRFProfileAddChannelRowStatus
}
STATUS current
DESCRIPTION
"This collection of object specifies the removed channel
and add channel list information from default DCA channel
list for a RF profile"
::= { ciscoLwappRFMIBGroups 13 }
END
Reference in New Issue Copy Permalink