david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
main
mibs/MIBS/dasan/DPW-ATM-MIB

1286 lines
44 KiB
Plaintext
Raw Permalink Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
DPW-ATM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Counter32, Unsigned32, mib-2
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
TruthValue, RowStatus, RowPointer
FROM SNMPv2-TC
PerfCurrentCount, PerfIntervalCount
FROM PerfHist-TC-MIB
InterfaceIndex
FROM IF-MIB
pwIndex
FROM PW-STD-MIB -- [PWMIB]
-- RFC Editor: Please replace
-- PWMIB with correct RFC
AtmVpIdentifier, AtmVcIdentifier
FROM ATM-TC-MIB
;
dpwAtmMIB MODULE-IDENTITY
LAST-UPDATED "200811200000Z" -- 20 November 2008 12:00:00 GMT
ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3)
Working Group"
CONTACT-INFO
"Senthilkumar Sathappan
Postal: 1000 Marconi Drive
Warrendale PA 15086
Tel: +1-724-742-614
Email: senthilkumar.sathappan@marconi.com
Marichetty Venkatesan
Postal: 1000 Marconi Drive
Warrendale PA 15086
Tel: +1-724-742-7058
Email: venkatesan.marichetty@marconi.com
Thomas D. Nadeau
Postal: Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
Tel: +1-978-497-3051
Email: tnadeau@cisco.com
Orly Nicklass
Postal: Nokia Siemens Networks
3 Hanagar st. Neve Ne'eman
Hod-Hasharon, Israel
Email: orly.nicklass@nsn.com
Discussion and general questions should be posed to
the PWE3 Working Group (pwe3@ietf.org)."
DESCRIPTION
"This MIB contains managed object definitions for
Pseudo Wire emulation of ATM over Packet Switched
Networks (PSN).
This MIB supplements the PW-STD-MIB module.
The PW-STD-MIB contains structures and MIB associations
generic to Pseudo-Wire (PW) emulation. PW-specific
MIBs (such as this) contain config and stats for specific
PW types.
Copyright (C) The IETF Trust (2008). This version of
this MIB module is part of RFC XXXX; see the RFC itself for
full legal notices."
-- RFC Ed.: replace XXXX with actual RFC number & remove this
-- note"
-- Revision history.
REVISION "200811200000Z" -- 20 November 2008 12:00:00 GMT
DESCRIPTION "Initial version published as RFC XXXX."
-- RFC Ed.: replace XXXX with actual RFC number & remove this
-- note"
::= { mplsATMPWMIB 1 }
-- RFC Editor: replace YYY with IANA-assigned number & remove this
-- note. Please see IANA considerations section.
-- Top-level components of this MIB
dpwAtmNotifications OBJECT IDENTIFIER
::= { dpwAtmMIB 0 }
dpwAtmObjects OBJECT IDENTIFIER
::= { dpwAtmMIB 1 }
--Generic ATM PW table for all types of ATM PW connection.
dpwAtmCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies generic information for an ATM PW
to be carried over PSN in any mode."
::= { dpwAtmObjects 1 }
dpwAtmCfgEntry OBJECT-TYPE
SYNTAX DpwAtmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a set of parameters for
the ATM PW that needs to be adapted and carried
over PSN. This table is indexed by pwIndex from
pwTable. An entry is created for every newly pwIndex
in the pwTable. Unless otherwise specified, all
read-write objects in this table MAY
be changed when the PW is defined as not active
and all RW objects values must persist
after reboot"
REFERENCE
"See [PWMIB] "
INDEX { pwIndex }
::= { dpwAtmCfgTable 1 }
DpwAtmCfgEntry ::= SEQUENCE {
dpwAtmCfgMaxCellConcatenation Unsigned32,
dpwAtmCfgFarEndMaxCellConcatenation Unsigned32,
dpwAtmCfgTimeoutMode INTEGER,
dpwAtmMaxCellConcatenationTimer Unsigned32
}
dpwAtmCfgMaxCellConcatenation OBJECT-TYPE
SYNTAX Unsigned32 (1..29)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN.
In non LDP or other signaling protocol environment,
this object MAY be changed at anytime, but traffic
might be interuppted, otherwise, it may be changed
when PW is not active."
DEFVAL { 1 }
::= { dpwAtmCfgEntry 1 }
dpwAtmCfgFarEndMaxCellConcatenation OBJECT-TYPE
SYNTAX Unsigned32 (1..29)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN as reported by
the far end. If no LDP in use, the object will either
return value 0 or allow setting it for calculating
protocol overhead."
::= { dpwAtmCfgEntry 2 }
dpwAtmCfgTimeoutMode OBJECT-TYPE
SYNTAX INTEGER
{
notApplicable (1),
disabled (2),
enabled (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects determines whether a packet can be
transmitted to the PSN based on time out expiration
for collecting cells or not. The actual handling of the
time out is implementation specific-as such this object
may be changed at any time under proper consideration of
traffic interupption effect."
DEFVAL { 3 }
::= { dpwAtmCfgEntry 3 }
dpwAtmMaxCellConcatenationTimer OBJECT-TYPE
SYNTAX Unsigned32 (300..4095)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This timer is used to concatenate the maximum ATM cell
packets in the configured timer value. The unit of the
timer is in microseconds."
DEFVAL { 1000 }
::= { dpwAtmCfgEntry 4 }
-- Device capable of implementing N:1, 1:1 and transparent cell
-- mode assumes to support the N:1 table for all
-- modes with respective applicable setting.
-- In such implementation, user can create an entry for either
-- 1:1 or transparent cell transport modes only
-- in pwAtmInboundNto1Table. The side effect of such
-- will be an automatic create of the respective line in the
-- pwAtmOutboundNto1Table.
-- ATM PW Outbound Table for N to 1 connection
dpwAtmOutboundNto1Table OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmOutboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the information for an ATM PW to
be carried over PSN in the outbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following: atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3).
"
::= { dpwAtmObjects 2 }
dpwAtmOutboundNto1Entry OBJECT-TYPE
SYNTAX DpwAtmOutboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all read-create objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot."
INDEX { pwIndex, dpwAtmOutboundNto1AtmIf ,
dpwAtmOutboundNto1Vpi }
::= { dpwAtmOutboundNto1Table 1 }
DpwAtmOutboundNto1Entry ::= SEQUENCE {
dpwAtmOutboundNto1AtmIf InterfaceIndex,
dpwAtmOutboundNto1Vpi AtmVpIdentifier,
dpwAtmOutboundNto1RowStatus RowStatus,
dpwAtmOutboundNto1MappedVpi INTEGER,
dpwAtmOutboundNto1OntId OCTET STRING
}
dpwAtmOutboundNto1AtmIf OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM Interface that receives cells from the ATM network."
::= { dpwAtmOutboundNto1Entry 1 }
dpwAtmOutboundNto1Vpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF"
::= { dpwAtmOutboundNto1Entry 2 }
dpwAtmOutboundNto1RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This Object is used to create, modify or delete a row in
this table."
::= { dpwAtmOutboundNto1Entry 3 }
dpwAtmOutboundNto1MappedVpi OBJECT-TYPE
SYNTAX INTEGER
{
disable (0),
enable (1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The egress generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active "
DEFVAL { 0 }
::= { dpwAtmOutboundNto1Entry 4 }
dpwAtmOutboundNto1OntId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the identification of an ONT."
::= { dpwAtmOutboundNto1Entry 5 }
-- ATM PW Inbound Table for N to 1 connection
dpwAtmInboundNto1Table OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmInboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the information for an ATM PW to
be carried over PSN in the Inbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following:atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3)."
::= { dpwAtmObjects 3 }
dpwAtmInboundNto1Entry OBJECT-TYPE
SYNTAX DpwAtmInboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all Read-Creat objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot."
INDEX { pwIndex, dpwAtmInboundNto1AtmIf ,
dpwAtmInboundNto1Vpi }
::= { dpwAtmInboundNto1Table 1 }
DpwAtmInboundNto1Entry ::= SEQUENCE {
dpwAtmInboundNto1AtmIf InterfaceIndex,
dpwAtmInboundNto1Vpi AtmVpIdentifier,
dpwAtmInboundNto1RowStatus RowStatus,
dpwAtmInboundNto1MappedVpi INTEGER
}
dpwAtmInboundNto1AtmIf OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM Interface that receives cells from the ATM network."
::= { dpwAtmInboundNto1Entry 1 }
dpwAtmInboundNto1Vpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF."
::= { dpwAtmInboundNto1Entry 2 }
dpwAtmInboundNto1RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This Object is used to modify or delete a row in
this table. This table is associated with dpwAtmOutboundNto1Table.
So a row can be created in this table through dpwAtmOutboundNto1Table"
::= { dpwAtmInboundNto1Entry 3 }
dpwAtmInboundNto1MappedVpi OBJECT-TYPE
SYNTAX INTEGER
{
disable (0),
enable (1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active."
DEFVAL { 0 }
::= { dpwAtmInboundNto1Entry 4 }
-- ATM PW QOS VCI-EXP Table
dpwAtmVciExpTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmVciExpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the ONT downstream VCI-EXP qos mapping
parameters. This exp value represents the queue-type in
exp-queue table"
::= { dpwAtmObjects 4 }
dpwAtmVciExpEntry OBJECT-TYPE
SYNTAX DpwAtmVciExpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for downstream ont qos."
INDEX { dpwAtmOntid, dpwAtmVpi, dpwAtmExpVci }
::= { dpwAtmVciExpTable 1 }
DpwAtmVciExpEntry ::= SEQUENCE {
dpwAtmOntid Unsigned32,
dpwAtmVpi Unsigned32,
dpwAtmExpVci Unsigned32,
dpwAtmVciExp Unsigned32,
dpwAtmExpRowStatus Unsigned32
}
dpwAtmOntid OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object represents the identification of an ONT."
::= { dpwAtmVciExpEntry 1 }
dpwAtmVpi OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object represents the downstream ont qos vpi value."
::= { dpwAtmVciExpEntry 2 }
dpwAtmExpVci OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The downstream ont qos vci value for corresponding vpi."
::= { dpwAtmVciExpEntry 3 }
dpwAtmVciExp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The exp value representing exp-queue table for downstream ont qos."
::= { dpwAtmVciExpEntry 4 }
dpwAtmExpRowStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This vci-exp table supports only exp value modification. This object becomes active
with default exp value when vci-qos table entries are created. This Object is
for internal use only and not configurable by user. "
::= { dpwAtmVciExpEntry 5 }
dpwAtmExpQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmExpQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the downstream ont qos EXP Queue related parameters."
::= { dpwAtmObjects 5 }
dpwAtmExpQosEntry OBJECT-TYPE
SYNTAX DpwAtmExpQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for downstream ont qos with queue-type
for corresponfing exp ."
INDEX { dpwAtmOntid, dpwAtmQosExp }
::= { dpwAtmExpQosTable 1 }
DpwAtmExpQosEntry ::= SEQUENCE {
dpwAtmQosExp Unsigned32,
dpwAtmExpQosMode Unsigned32,
dpwAtmExpQosPriority Unsigned32,
dpwAtmExpQosWeight Unsigned32,
dpwAtmExpQosRowStatus Unsigned32
}
dpwAtmQosExp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies the exp value corresponding to downstream ont qos."
::= { dpwAtmExpQosEntry 1 }
dpwAtmExpQosMode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This obejct specifies the exp queue-type for downstream ont qos ."
::= { dpwAtmExpQosEntry 2 }
dpwAtmExpQosPriority OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifes the priority for queue-type of strict priority(SP)."
::= { dpwAtmExpQosEntry 3 }
dpwAtmExpQosWeight OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies the weight for queue-type of weighted round robin(WRR)."
::= { dpwAtmExpQosEntry 4 }
dpwAtmExpQosRowStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This Object is for internal use only and not configurable by user. This table will
have default values unless modified by the user."
::= { dpwAtmExpQosEntry 5 }
dpwAtmVciQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmVciQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains VCI Queue related parameters for upstream ont qos."
::= { dpwAtmObjects 6 }
dpwAtmVciQosEntry OBJECT-TYPE
SYNTAX DpwAtmVciQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for upstream ont qos vci-qos."
INDEX { dpwAtmOntid, dpwAtmVpi, dpwAtmExpVci }
::= { dpwAtmVciQosTable 1 }
DpwAtmVciQosEntry ::= SEQUENCE {
dpwAtmVciQosClass INTEGER,
dpwAtmVciQosPCR Unsigned32,
dpwAtmVciQosSCR Unsigned32,
dpwAtmVciQosMBS Unsigned32,
dpwAtmVciQosCDVT Unsigned32,
dpwAtmVciQosRowStatus Unsigned32
}
dpwAtmVciQosClass OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This objects specifies class type for upstream ont qos vci."
::= { dpwAtmVciQosEntry 1 }
dpwAtmVciQosPCR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies the peak cell rate for corresponding upstream ont qos.This value
should be in a multiples of 151 only"
::= { dpwAtmVciQosEntry 2 }
dpwAtmVciQosSCR OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies the substainable cell rate for upstream ont qos.This value
should be in a multiples of 151 only"
::= { dpwAtmVciQosEntry 3 }
dpwAtmVciQosMBS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies maximum burst size of corresponding vci in upstream ont qos."
::= { dpwAtmVciQosEntry 4 }
dpwAtmVciQosCDVT OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This object specifies cell delay variance tolerance corresponds to vci in upstream ont qos."
::= { dpwAtmVciQosEntry 5 }
dpwAtmVciQosRowStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This Object is used to create and delete a row in this table.
When the Row status is active, whenever user configures in OLT, ONT is also configured.
For row creation, user is suggested to configure the qos parameters after configuring rowstatus
to create and wait. Then make the row status active. Creation or deletion of vci-qos table
automatically creates/deletes vci-exp table."
::= { dpwAtmVciQosEntry 6 }
-- The following supplement the counters presented in the
-- PW generic MIB
-- ATM PW Performance Current Table.
dpwAtmPerfCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The current 15 minute interval counts are in
this table.
This table provides performance information per ATM PW."
::= { dpwAtmObjects 7 }
dpwAtmPerfCurrentEntry OBJECT-TYPE
SYNTAX DpwAtmPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
pwAtmCfgTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwAtmPerfInterval table and the counts in this entry
are reset to zero."
INDEX { pwIndex }
::= { dpwAtmPerfCurrentTable 1 }
DpwAtmPerfCurrentEntry ::= SEQUENCE {
dpwAtmPerfCurrentMissingPkts PerfCurrentCount,
dpwAtmPerfCurrentPktsReOrder PerfCurrentCount,
dpwAtmPerfCurrentPktsMisOrder PerfCurrentCount,
dpwAtmPerfCurrentPktsTimeout PerfCurrentCount,
dpwAtmPerfCurrentCellsXmit PerfCurrentCount,
dpwAtmPerfCurrentCellsDropped PerfCurrentCount,
dpwAtmPerfCurrentCellsReceived PerfCurrentCount,
dpwAtmPerfCurrentUnknownCells PerfCurrentCount
}
dpwAtmPerfCurrentMissingPkts OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { dpwAtmPerfCurrentEntry 1 }
dpwAtmPerfCurrentPktsReOrder OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature."
::= { dpwAtmPerfCurrentEntry 2 }
dpwAtmPerfCurrentPktsMisOrder OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order (via control word
sequence numbers)."
::= { dpwAtmPerfCurrentEntry 3 }
dpwAtmPerfCurrentPktsTimeout OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration
while attempting to collect cells."
::= { dpwAtmPerfCurrentEntry 4 }
dpwAtmPerfCurrentCellsXmit OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted cells."
::= { dpwAtmPerfCurrentEntry 5 }
dpwAtmPerfCurrentCellsDropped OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { dpwAtmPerfCurrentEntry 6 }
dpwAtmPerfCurrentCellsReceived OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received cells."
::= { dpwAtmPerfCurrentEntry 7 }
dpwAtmPerfCurrentUnknownCells OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode."
::= { dpwAtmPerfCurrentEntry 8 }
-- End ATM PW Performance Current Interval Table
-- ATM PW Performance Interval Table.
dpwAtmPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per ATM PW
similar to the pwAtmPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period. "
::= { dpwAtmObjects 8 }
dpwAtmPerfIntervalEntry OBJECT-TYPE
SYNTAX DpwAtmPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for
every pwAtmPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zero for the next current 15 minute interval. "
INDEX { pwIndex, dpwAtmPerfIntervalNumber }
::= { dpwAtmPerfIntervalTable 1 }
DpwAtmPerfIntervalEntry ::= SEQUENCE {
dpwAtmPerfIntervalNumber Unsigned32,
dpwAtmPerfIntervalValidData TruthValue,
dpwAtmPerfIntervalDuration Unsigned32,
dpwAtmPerfIntervalMissingPkts PerfIntervalCount,
dpwAtmPerfIntervalPktsReOrder PerfIntervalCount,
dpwAtmPerfIntervalPktsMisOrder PerfIntervalCount,
dpwAtmPerfIntervalPktsTimeout PerfIntervalCount,
dpwAtmPerfIntervalCellsXmit PerfIntervalCount,
dpwAtmPerfIntervalCellsDropped PerfIntervalCount,
dpwAtmPerfIntervalCellsReceived PerfIntervalCount,
dpwAtmPerfIntervalUnknownCells PerfIntervalCount,
dpwAtmPerfIntervalTime OCTET STRING
}
dpwAtmPerfIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, and
the interval identified by N is the interval immediately
preceding the one identified by N-1. The minimum range of
N is 1 through 4. The default range is 1 through 32. The
maximum value of N is 96."
::= { dpwAtmPerfIntervalEntry 1 }
dpwAtmPerfIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval
is valid."
::= { dpwAtmPerfIntervalEntry 2 }
dpwAtmPerfIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { dpwAtmPerfIntervalEntry 3 }
dpwAtmPerfIntervalMissingPkts OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control
word sequence number gaps)."
::= { dpwAtmPerfIntervalEntry 4 }
dpwAtmPerfIntervalPktsReOrder OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature."
::= { dpwAtmPerfIntervalEntry 5 }
dpwAtmPerfIntervalPktsMisOrder OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order (via control word
sequence numbers)."
::= { dpwAtmPerfIntervalEntry 6 }
dpwAtmPerfIntervalPktsTimeout OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration."
::= { dpwAtmPerfIntervalEntry 7 }
dpwAtmPerfIntervalCellsXmit OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted cells."
::= { dpwAtmPerfIntervalEntry 8 }
dpwAtmPerfIntervalCellsDropped OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { dpwAtmPerfIntervalEntry 9 }
dpwAtmPerfIntervalCellsReceived OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received cells."
::= { dpwAtmPerfIntervalEntry 10 }
dpwAtmPerfIntervalUnknownCells OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode."
::= { dpwAtmPerfIntervalEntry 11 }
dpwAtmPerfIntervalTime OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp value of the system in hours, minutes and seconds
when data is received for particular pseudo-wire for every
15-minutes"
::= { dpwAtmPerfIntervalEntry 12 }
-- End ATM PW Performance Interval Table
-- ATM PW 1day Performance Table
dpwAtmPerf1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per ATM PW
similar to the pwAtmPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month."
::= { dpwAtmObjects 9 }
dpwAtmPerf1DayIntervalEntry OBJECT-TYPE
SYNTAX DpwAtmPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry is created in this table by the agent
for every entry in the pwAtmCfgTable table."
INDEX { pwIndex,dpwAtmPerf1DayIntervalNumber }
::= { dpwAtmPerf1DayIntervalTable 1 }
DpwAtmPerf1DayIntervalEntry ::= SEQUENCE {
dpwAtmPerf1DayIntervalNumber Unsigned32,
dpwAtmPerf1DayIntervalValidData TruthValue,
dpwAtmPerf1DayIntervalDuration Unsigned32,
dpwAtmPerf1DayIntervalMissingPkts Counter32,
dpwAtmPerf1DayIntervalPktsReOrder Counter32,
dpwAtmPerf1DayIntervalPktsMisOrder Counter32,
dpwAtmPerf1DayIntervalPktsTimeout Counter32,
dpwAtmPerf1DayIntervalCellsXmit Counter32,
dpwAtmPerf1DayIntervalCellsDropped Counter32,
dpwAtmPerf1DayIntervalCellsReceived Counter32,
dpwAtmPerf1DayIntervalUnknownCells Counter32,
dpwAtmPerf1DayIntervalTime OCTET STRING
}
dpwAtmPerf1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..365)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively"
::= { dpwAtmPerf1DayIntervalEntry 1 }
dpwAtmPerf1DayIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates if the data for this interval
is valid."
::= { dpwAtmPerf1DayIntervalEntry 2 }
dpwAtmPerf1DayIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { dpwAtmPerf1DayIntervalEntry 3 }
dpwAtmPerf1DayIntervalMissingPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { dpwAtmPerf1DayIntervalEntry 4 }
dpwAtmPerf1DayIntervalPktsReOrder OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature."
::= { dpwAtmPerf1DayIntervalEntry 5 }
dpwAtmPerf1DayIntervalPktsMisOrder OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered."
::= { dpwAtmPerf1DayIntervalEntry 6 }
dpwAtmPerf1DayIntervalPktsTimeout OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration."
::= { dpwAtmPerf1DayIntervalEntry 7 }
dpwAtmPerf1DayIntervalCellsXmit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted cells."
::= { dpwAtmPerf1DayIntervalEntry 8 }
dpwAtmPerf1DayIntervalCellsDropped OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { dpwAtmPerf1DayIntervalEntry 9 }
dpwAtmPerf1DayIntervalCellsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received cells."
::= { dpwAtmPerf1DayIntervalEntry 10 }
dpwAtmPerf1DayIntervalUnknownCells OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI
or VCI value. This object is relevant only in N:1 mode."
::= { dpwAtmPerf1DayIntervalEntry 11 }
dpwAtmPerf1DayIntervalTime OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp value of the system in hours, minutes and seconds
when data is received for particular pseudo-wire for every
day"
::= { dpwAtmPerf1DayIntervalEntry 12 }
-- End of ATM PW Performance table
-- PW OAM Table
dpwOamTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwOamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies to enable/disable OAM
on the PW associated to the specified pwIndex.
It also shows the defects of the PW OAM."
::= { dpwAtmObjects 10 }
dpwOamEntry OBJECT-TYPE
SYNTAX DpwOamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot."
INDEX { pwIndex }
::= { dpwOamTable 1}
DpwOamEntry ::= SEQUENCE {
dpwOamEnable TruthValue,
dpwOamDefect INTEGER,
dpwOamRowStatus RowStatus
}
dpwOamEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates if OAM is enabled for this PW.
It MAY be changed at any time."
DEFVAL { true }
::= { dpwOamEntry 1 }
dpwOamDefect OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This specifies the defect states of PW OAM"
::= { dpwOamEntry 2 }
dpwOamRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row. None of the
read-create objects in the conceptual rows may be changed
when this object is in the active(1) state."
::= { dpwOamEntry 3 }
-- End of PW OAM Table
-- ATMOAM TABLE
dpwAtmoamTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmoamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies to enable/disable CC Generation and also
to set the Flow Type as E2E / SEG."
::= { dpwAtmObjects 11 }
dpwAtmoamEntry OBJECT-TYPE
SYNTAX DpwAtmoamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot."
INDEX { pwIndex }
::= { dpwAtmoamTable 1 }
DpwAtmoamEntry ::= SEQUENCE {
dpwCcStatus TruthValue,
dpwFlowType INTEGER,
dpwAtmoamRowStatus RowStatus,
dpwFrequencyTimerIntvl INTEGER
}
dpwCcStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to enable / disable the CC Status."
DEFVAL { false }
::= { dpwAtmoamEntry 1 }
dpwFlowType OBJECT-TYPE
SYNTAX INTEGER {
ete (1),
seg (2),
both (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to set the flow type as E2E / SEG / Both."
DEFVAL { ete }
::= { dpwAtmoamEntry 2 }
dpwAtmoamRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row. None of the
read-create objects in the conceptual rows may be changed
when this object is in the active(1) state."
::= { dpwAtmoamEntry 3 }
dpwFrequencyTimerIntvl OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to set the Frequency Timer Interval.
The frequency timer interval can be 1 or 2"
DEFVAL { 1 }
::= { dpwAtmoamEntry 4 }
-- End of ATMOAM Table
-- VP SHAPING Table
-- jira id DASAN - 84
dpwAtmVpShapingTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmVpShapingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains VP Shaping related parameters for upstream ont qos."
::= { dpwAtmObjects 12 }
dpwAtmVpShapingEntry OBJECT-TYPE
SYNTAX DpwAtmVpShapingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for upstream ont qos vci-qos."
INDEX { dpwAtmOntid, dpwAtmVpi }
::= { dpwAtmVpShapingTable 1 }
DpwAtmVpShapingEntry ::= SEQUENCE {
dpwAtmVpShapingBandwidth Unsigned32,
dpwAtmVpShapingRowStatus Unsigned32
}
dpwAtmVpShapingBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (300..358795)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Vp shaping bandwidth for upstream ATM cell packets.
The unit of bandwidth is in cell/seconds."
DEFVAL { 10000 }
::= { dpwAtmVpShapingEntry 1 }
dpwAtmVpShapingRowStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" This Object is used to create, modify and delete a row in this table.
When the Row status is active, whenever user configures in OLT, ONT is also configured.
For row creation, user is suggested to configure the bandwidth parameter after setting the
row status to create and wait. Then make the row status active."
::= { dpwAtmVpShapingEntry 2 }
-- End of VP SHAPING Table
-- ATM OAM Stats Table.
-- JIRAID : DASAN-664 Implementation of PW OAM Statistics - SNMP support
dpwAtmOamStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DpwAtmOamStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OAM statistic counts are in
this table.
This table provides OAM statistics information per ATM PW."
::= { dpwAtmObjects 13 }
dpwAtmOamStatsEntry OBJECT-TYPE
SYNTAX DpwAtmOamStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created when AIS/RDI cells are received.
Number of OAM cells Txmitted and received are incremented"
INDEX { pwIndex }
::= { dpwAtmOamStatsTable 1 }
DpwAtmOamStatsEntry ::= SEQUENCE {
dpwAtmOamStatsOamCellsRx PerfCurrentCount,
dpwAtmOamStatsOamCellsTx PerfCurrentCount
}
dpwAtmOamStatsOamCellsRx OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of OAM Cells received."
::= { dpwAtmOamStatsEntry 1 }
dpwAtmOamStatsOamCellsTx OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of OAM Cells transmitted."
::= { dpwAtmOamStatsEntry 2 }
-- End of ATM OAM Stats Table.
END
Reference in New Issue Copy Permalink