mibs/MIBS/junos/JNX-PPP-MIB

3076 lines
112 KiB
Plaintext
Raw Permalink Normal View History

2023-12-05 12:25:34 +01:00
--
-- Juniper Enterprise Specifics MIB
--
-- Copyright (c) 2010-2012, Juniper Networks, Inc.
-- All rights reserved.
--
-- The contents of this document are subject to change without notice.
--
JNX-PPP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, IpAddress, TimeTicks, Unsigned32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, TruthValue, RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex, InterfaceIndex, InterfaceIndexOrZero
FROM IF-MIB
Ipv6AddressIfIdentifier
FROM IPV6-TC
jnxPppMibRoot
FROM JUNIPER-SMI ;
jnxPppMIB MODULE-IDENTITY
LAST-UPDATED "201309190942Z" -- 19-Sept-13 03:12 PM EST
ORGANIZATION "Juniper Networks, Inc."
CONTACT-INFO
" Juniper Networks, Inc.
Postal: 10 Technology Park Drive
Westford, MA 01886-3146
USA
Tel: +1 978 589 5800
Email: mib@Juniper.net"
DESCRIPTION
"The Point-to-Point Protocol (PPP) MIB for the Juniper enterprise."
-- Revision History
REVISION "201309190000Z" -- 19-Sept-13 03:12 PM EST - JUNOS 13.1
DESCRIPTION
"Updated the revision history and LAST-UPDATED field."
REVISION "201306130000Z" -- 13-Jun-13 05:32 AM EST - JUNOS 13.1
DESCRIPTION
"Deprecated InterfaceIndex type and added InterfaceIndexOrZero type
for jnxPppNextIfIndex, jnxPppMlPppNextLinkIfIndex and
jnxPppMlPppNextNetworkIfIndex."
REVISION "201206080000Z" -- 08-Jun-12 03:12 PM EST - JUNOS 12.1
DESCRIPTION
"Changes are done to change all Data packet/octet counters from
32 to 64 bit counter. 32 bit counters were too small for data
packets/octects and were consumed too early. All old counters are
deprecated and new counters are added."
REVISION "201111290000Z" -- 29-Nov-11 03:12 PM EST - JUNOS 11.4
DESCRIPTION
"Deprecated Integer32 type jnxPppLinkStatusLocalMagicNumber,
jnxPppLinkStatusRemoteMagicNumber and added Unsigned32 type
jnxPppLinkStatusLocalMagicNumber1, jnxPppLinkStatusLocalMagicNumber1
under jnxPppLinkStatusTable"
REVISION "201007220942Z" -- 22-Jul-10 03:12 PM EST - JUNOS 11.0
DESCRIPTION
"Initial version."
::= { jnxPppMibRoot 1 }
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- Textual conventions
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
JnxPppAuthentication ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"Specifies the type(s) of PPP authentication used, if any:
none No authentication is negotiated.
pap PAP negotiation only.
chap CHAP negotiation only.
papChap PAP negotiation is attempted first; if fails, attempt CHAP.
chapPap CHAP negotiation is attempted first; if fails, attempt PAP."
SYNTAX INTEGER {
none (0),
pap (1),
chap (2),
papChap (3),
chapPap (4) }
--+++++++++
JnxPppMlPppBundleName ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"MLPPP Bundle name. The bundle name is a characteristic of a MLPPP
network interface."
SYNTAX OCTET STRING (SIZE(1..60))
--+++++
JnxPppAuthentication2 ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the type(s) of PPP authentication used, if any:
none No authentication is negotiated.
pap PAP negotiation.
chap CHAP negotiation.
eap EAP negotiation."
SYNTAX INTEGER {
none (0),
pap (1),
chap (2),
eap (3) }
JnxNibbleConfig ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A configuration variable comprised of nibbles i.e. 4 bits, such that
a client can supply a list of 0 to 8 selections. The least
significant nibble is the first value of the list, and the most
significant nibble is the last value. The value in each field
ranges from 0 to 15, however the first nibble with value 0 indicates
the end of the list. Repetition of values is not allowed.
Segregation of values in not allowed.
Example valid encoding:
0x00000321
0x00083E12
Not a valid encoding:
0x00000121 will return an error
0x01002001 will return an error."
SYNTAX INTEGER
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
-- Managed objects
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jnxPPPObjects OBJECT IDENTIFIER ::= { jnxPppMIB 1 }
--
-- This MIB contains managed objects for PPP interfaces. Management objects are
-- provided to query for an available interface index, and to create/delete
-- interfaces of this type. Creating/deleting this interface type using this
-- MIB has the side effect of creating/deleting corresponding entries in the
-- Interface MIB ifTable/ifXTable, and in the Jnxper Enterprise Interface MIB
-- jnxIfTable.
--This MIB acts as a supplement to IETF MIBs RFC1471 PPP-LCP-MIB .
-- MIB object definitions are organized into the following
-- Functional sections:
--
jnxPppLcp OBJECT IDENTIFIER ::= { jnxPPPObjects 1 }
jnxPppSec OBJECT IDENTIFIER ::= { jnxPPPObjects 2 }
jnxPppIp OBJECT IDENTIFIER ::= { jnxPPPObjects 3 }
jnxPppOsi OBJECT IDENTIFIER ::= { jnxPPPObjects 4 }
jnxPppSession OBJECT IDENTIFIER ::= { jnxPPPObjects 5 }
jnxPppMlPpp OBJECT IDENTIFIER ::= { jnxPPPObjects 6 }
jnxPppSummary OBJECT IDENTIFIER ::= { jnxPPPObjects 7 }
jnxPppIpv6 OBJECT IDENTIFIER ::= { jnxPPPObjects 8 }
jnxPppGlobalConfig OBJECT IDENTIFIER ::= { jnxPPPObjects 9 }
-- /////////////////////////////////////////////////////////////////////////////
-- PPP LCP
-- This section defines objects used to manage the PPP Link / LCP layer of PPP.
-- The jnxPppLinkStatusTable complements RFC1471 pppLinkStatusTable, providing
--status indications regarding the operation of network protocols over each
-- link. The addition/removal of a network protocol service is accomplished
-- outside this MIB. The jnxPppLinkConfigTable complements RFC1471
-- providing the ability to create/delete instances of PPP links and providing
-- for configuration of option parameter values (if any) not found in the
-- standard MIB, to be used during LCP negotiation.
-- /////////////////////////////////////////////////////////////////////////////
-- The PPP Link Status Table
--
jnxPppLinkStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppLinkStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for PPP interfaces present in the system."
::= { jnxPppLcp 1 }
jnxPppLinkStatusEntry OBJECT-TYPE
SYNTAX JnxPppLinkStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of a PPP interface."
INDEX { ifIndex }
::= { jnxPppLinkStatusTable 1 }
JnxPppLinkStatusEntry ::= SEQUENCE {
jnxPppLinkStatusTerminateReason INTEGER,
jnxPppLinkStatusTerminateNegFailOption INTEGER,
jnxPppLinkStatusInKeepaliveRequests Counter32,
jnxPppLinkStatusOutKeepaliveRequests Counter32,
jnxPppLinkStatusInKeepaliveReplies Counter32,
jnxPppLinkStatusOutKeepaliveReplies Counter32,
jnxPppLinkStatusKeepaliveFailures Counter32,
jnxPppLinkStatusLocalMagicNumber Integer32,
jnxPppLinkStatusRemoteMagicNumber Integer32,
jnxPppLinkStatusLocalAuthentication JnxPppAuthentication2,
jnxPppLinkStatusTunnelIfIndex InterfaceIndexOrZero,
jnxPppLinkStatuslcpRenegoTerminates Counter32,
jnxPppLinkStatusLocalMagicNumber1 Unsigned32,
jnxPppLinkStatusRemoteMagicNumber1 Unsigned32}
jnxPppLinkStatusTerminateReason OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
adminDisable(2),
lowerLayerDown(3),
noUpperInterface(4),
authenticationFailure(5),
peerTerminated(6),
peerRenegotiated(7),
maxRetriesExceeded(8),
negotiationFailure(9),
keepaliveFailure(10),
sessionTimeout(11),
inactivityTimeout(12),
addressLeaseExpired(13),
adminLogout(14),
tunnelFailed(15),
tunnelDisconnected(16),
loopback(17) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reason the PPP link was terminated:
none None.
other Not specified.
adminDisable Interface administratively disabled.
lowerLayerDown Underlying interface is down.
noUpperInterface No interface above PPP.
authenticationFailure Authentication failed.
peerTerminated Peer initiated termination.
peerRenegotiated Peer initiated renegotiation.
maxRetriesExceeded Maximum number of config retries exceeded.
negotiationFailure Failed to negotiate LCP option.
keepaliveFailure Keepalive failed.
sessionTimeout Maximum session period expired.
inactivityTimeout Maximum inactivity period expired.
addressLeaseExpired Lease for network address expired.
adminLogout Session administratively terminated.
tunnelFailed Associated tunnel failed.
tunnelDisconnected Associated tunnel disconnected.
loopback Loopback detected."
::= { jnxPppLinkStatusEntry 1 }
jnxPppLinkStatusTerminateNegFailOption OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
localMru(2),
remoteMru(3),
localMagicNumber(4),
remoteMagicNumber(5),
localAuthentication(6),
localToRemoteProtocolCompression(7),
localToRemoteACCompression(8) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reports the PPP LCP option for which negotiation failed,
when jnxPppLinkStatusTerminateReason has the value negotiationFailure."
::= { jnxPppLinkStatusEntry 2 }
jnxPppLinkStatusInKeepaliveRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of keepalive requests received."
::= { jnxPppLinkStatusEntry 3 }
jnxPppLinkStatusOutKeepaliveRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of keepalive requests transmitted."
::= { jnxPppLinkStatusEntry 4 }
jnxPppLinkStatusInKeepaliveReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of keepalive replies received."
::= { jnxPppLinkStatusEntry 5 }
jnxPppLinkStatusOutKeepaliveReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of keepalive replies transmitted."
::= { jnxPppLinkStatusEntry 6 }
jnxPppLinkStatusKeepaliveFailures OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of keepalive failures detected."
::= { jnxPppLinkStatusEntry 7 }
jnxPppLinkStatusLocalMagicNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Magic number negotiated for the local side.
This has been deprecated and replaced by
jnxPppLinkStatusLocalMagicNumber1"
::= { jnxPppLinkStatusEntry 8 }
jnxPppLinkStatusRemoteMagicNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Magic number negotiated for the remote side.
This has been deprecated and replaced by
jnxPppLinkStatusRemoteMagicNumber1"
::= { jnxPppLinkStatusEntry 9 }
jnxPppLinkStatusLocalAuthentication OBJECT-TYPE
SYNTAX JnxPppAuthentication2
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Authentication protocol negotiated for the local side."
::= { jnxPppLinkStatusEntry 10 }
jnxPppLinkStatusTunnelIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of an associated interface pertaining to a tunneling
protocol, or zero if no such interface exists.The type of tunneling
interface can be identified from information in the entries in
ifTable and jnxIfTable for this tunnel interface."
::= { jnxPppLinkStatusEntry 11 }
jnxPppLinkStatuslcpRenegoTerminates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times lcp terminated due to peer exceeding max renegotiation
attempts."
::= { jnxPppLinkStatusEntry 12 }
jnxPppLinkStatusLocalMagicNumber1 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Magic number negotiated for the local side."
::= { jnxPppLinkStatusEntry 13 }
jnxPppLinkStatusRemoteMagicNumber1 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Magic number negotiated for the remote side."
::= { jnxPppLinkStatusEntry 14 }
--
-- The PPP Link Configuration Table
--
jnxPppLinkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppLinkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for PPP interfaces present in the system."
::= { jnxPppLcp 2 }
jnxPppLinkConfigEntry OBJECT-TYPE
SYNTAX JnxPppLinkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of a PPP interface.
Creating or deleting entries in this table causes corresponding entries
for be created or deleted in ifTable,ifXTable,jnxIfTable."
INDEX { jnxPppLinkConfigIfIndex }
::= { jnxPppLinkConfigTable 1 }
JnxPppLinkConfigEntry ::= SEQUENCE {
jnxPppLinkConfigIfIndex InterfaceIndex,
jnxPppLinkConfigRowStatus RowStatus,
jnxPppLinkConfigLowerIfIndex InterfaceIndexOrZero,
jnxPppLinkConfigKeepalive Integer32,
jnxPppLinkConfigAuthentication JnxPppAuthentication,
jnxPppLinkConfigMaxAuthenRetries Integer32,
jnxPppLinkConfigStandardIfIndex InterfaceIndex,
jnxPppLinkConfigChapMinChallengeLength Integer32,
jnxPppLinkConfigChapMaxChallengeLength Integer32,
jnxPppLinkConfigPassiveMode INTEGER,
jnxPppLinkConfigAuthenticatorLogicalSystem OCTET STRING,
jnxPppLinkConfigAuthenticatorRoutingInstance OCTET STRING,
jnxPppLinkConfigAaaProfile OCTET STRING,
jnxPppLinkConfigAuthentication2 JnxNibbleConfig,
jnxPppLinkConfigIgnoreMagicNumberMismatch INTEGER,
jnxPppLinkConfigMaxLcpRenegotiation Integer32}
jnxPppLinkConfigIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the PPP interface. When creating entries in this
table, suitable values for this object are determined by reading
jnxPppNextIfIndex."
::= { jnxPppLinkConfigEntry 1 }
jnxPppLinkConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Controls creation or deletion of entries in this table with READ-CREATE
maximum access according to the RowStatus textual convention,
constrained to support the following values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
jnxPppLinkConfigRowStatus
jnxPppLinkConfigLowerIfIndex
In addition, when creating an entry the following conditions must hold:
A value for jnxPppLinkConfigIndex must have been determined
previously, by reading jnxPppNextIfIndex.The interface identified
by jnxPppLinkConfigLowerIfIndex must exist. A corresponding entry
in Table or ifXTable or jnxIfTable is created or destroyed as a
result of creating or destroying an entry in this table.
The following values can be read from this object:
active(1)"
::= { jnxPppLinkConfigEntry 2 }
jnxPppLinkConfigLowerIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of an interface over which this PPP interface is to be
layered.A value of zero indicates no layering. An implementation may
choose to require that a non-zero value be configured at entry creation."
::= { jnxPppLinkConfigEntry 3 }
jnxPppLinkConfigKeepalive OBJECT-TYPE
SYNTAX Integer32 (0..64800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Keepalive interval in seconds. A value of zero disables keepalive.
Keepalive is performed using LCP Echo."
DEFVAL { 30 }
::= { jnxPppLinkConfigEntry 4 }
jnxPppLinkConfigAuthentication OBJECT-TYPE
SYNTAX JnxPppAuthentication
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Specifies the type(s) of authentication, if any, to be negotiated
with the peer:
none No authentication is negotiated.
pap PAP negotiation only.
chap CHAP negotiation only.
papChap PAP negotiation is attempted first; if fails, attempt CHAP.
chapPap CHAP negotiation is attempted first; if fails, attempt PAP.
If authentication negotiation is not supported for this PPP interface,
then any attempt to explicitely set this object if READ-CREATE maximum
access is supported will result in a notWritable error and it will be
implicitily set to the DEFVAL on row creation. Setting this object to
none(0) will set jnxPppLinkConfigAuthenticatorRouting Instance object
to an empty string.
This object returns a null(0) value on the get operation. New object
jnxPppLinkConfigAuthentication2 will reflect the configured values. Setting
this object along with the jnxPppLinkConfigAuthentication2 object will return
an inconsistentValue error."
DEFVAL { none }
::= { jnxPppLinkConfigEntry 5 }
jnxPppLinkConfigMaxAuthenRetries OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of authentication retries permitted, in addition to a
failed initial attempt. If all retries fail, the link is reset.
If authentication negotiation is not supported for this PPP interface,
then any attempt to explicitely set this object if READ-CREATE
maximum access is supported will result in a notWritable error and
it will be implicitily set to the DEFVAL on row creation."
DEFVAL { 0 }
::= { jnxPppLinkConfigEntry 6 }
jnxPppLinkConfigStandardIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex value for this interface in the standard PPP MIBs.
The ifIndex value for PPP interfaces is not the same for both
proprietary and standard MIB tables pertaining to PPP interface.
Therefore this value is provide to simply cross referencing
standard PPP and proprietary PPP MIB information."
::= { jnxPppLinkConfigEntry 7 }
jnxPppLinkConfigChapMinChallengeLength OBJECT-TYPE
SYNTAX Integer32 (8..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum value of the CHAP authenticator challenge length value.
This value is never greater than
jnxPppLinkConfigChapMaxChallengeLength."
DEFVAL { 16 }
::= { jnxPppLinkConfigEntry 8 }
jnxPppLinkConfigChapMaxChallengeLength OBJECT-TYPE
SYNTAX Integer32 (8..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum value of the CHAP authenticator challenge length value.
This value is never less than jnxPppLinkConfigChapMinChallengeLength."
DEFVAL { 32 }
::= { jnxPppLinkConfigEntry 9 }
jnxPppLinkConfigPassiveMode OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When enabled, LCP state machine is forced into passive mode on lower layer
UP message. It adds compatibility with slow and buggy clients."
DEFVAL { disable }
::= { jnxPppLinkConfigEntry 10 }
jnxPppLinkConfigAuthenticatorLogicalSystem OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the logical system to be used for authentication on the
PPP interface.With READ-CREATE maximum access , setting this object
statically binds the authenticating logical system with the PPP
interface. If this object is not explicitly set or it is set to null
string, then this object is ignored and the virtual router used for
authentication is determined by other means.
On a Set operation, if the value of this object is not null and does
not correspond to an existing virtual router, then an
inconsistentValue error is returned. Setting this object to a non-null
string returns inconsistentValue error if jnxPppLinkConfigAuthentication
object is none(0) or not configured."
::= { jnxPppLinkConfigEntry 11 }
jnxPppLinkConfigAuthenticatorRoutingInstance OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the routing instancebe used for authentication on the
PPP interface. With READ-CREATE maximum access, setting this object
statically binds the authenticating routing instance with the PPP
interface.If this object is not explicitly set or it is set to null
string, then this object is ignored and the virtual router used for
authentication is determined by other means. On a Set operation,
if the value of this object is not null and does not correspond to
an existing virtual router, then an inconsistentValue error is returned.
Setting this object to a non-null string returns inconsistentValue error
if jnxPppLinkConfigAuthentication object is
none(0) or not configured."
::= { jnxPppLinkConfigEntry 12 }
jnxPppLinkConfigAaaProfile OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the AAA profile to be used for authentication on the
PPP interface. With READ-CREATE maximum access, setting this
object statically binds the AAA profile with the PPP interface.
If this object is not explicitly set or it is set to null string,
then this object is ignored. On a Set operation, if the value of
this object is not null and does not correspond to an existing
AAA profile, then an inconsistentValue error is returned."
::= { jnxPppLinkConfigEntry 13 }
jnxPppLinkConfigAuthentication2 OBJECT-TYPE
SYNTAX JnxNibbleConfig
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A configuration variable comprised of nibbles i.e. 4 bits, such
that a client can supply a list of 0 to 8 selections. The least
significant nibble is the first value of the list, and the most
significant nibble is the last value. The value in each field
ranges from 0 to 15, however the first nibble with value 0
indicates the end of the list. Repetition of values is not allowed.
Segregation
of values is not allowed.
Valid Values are:
none - 0
pap - 1
chap - 2
eap - 3
Example valid encoding:
0x00000321
0x00000012
Not a valid encoding:
0x00000121
0x01002001
If authentication negotiation is not supported for this PPP interface
and with READ-CREATE maximum access ,any attempt to explicitly set this
object will result in a notWritable error and it will be implicitly
set to the DEFVAL on row creation. Setting this object to null will set
jnxPppLinkConfigAuthenticatorRoutingInstance object to an empty string.
Setting this object along with the jnxPppLinkConfigAuthentication object
will return an inconsistentValue error."
DEFVAL { 0 }
::= { jnxPppLinkConfigEntry 14 }
jnxPppLinkConfigIgnoreMagicNumberMismatch OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ignore magic number mismatch option of the PPP interface determines
the action to be taken, when the peer has not negotiated any value yet
sent null or invalid magic number in the LCP echo packets.
The two actions
that can be configured are:
1) Ignore the mismatch and retain connection
2) Disallow the mismatch and terminate connection"
DEFVAL { disable }
::= { jnxPppLinkConfigEntry 15 }
jnxPppLinkConfigMaxLcpRenegotiation OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of allowed lcp renegotiation attempts from peer."
DEFVAL { 30 }
::= { jnxPppLinkConfigEntry 16 }
--
-- IfIndex selection for creating new PPP interfaces in jnxPppLinkConfigTable.
--
-- NOTE: This object is placed after jnxPppLinkConfigTable so
-- that jnxPppLinkStatusTable and jnxPppLinkConfigTable have the
-- same relative MIB node positions below the jnxPppLcp node
-- (jnxPppLcp.1 and jnxPppLcp.2, respectively) as their counterpart
-- Status and Config tables in RFC1471.
--
jnxPppNextIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Coordinate ifIndex value allocation for entries in the
jnxPppLinkConfigTable. A GET of this object returns the next available
ifIndex value to be used to create an entry in the associated interface
table; or zero, if no valid ifIndex value is available.This object
also returns a value of zero when it is the lexicographic successor
of a varbind presented in an SNMP GETNEXT or GETBULK request, for which
circumstance it is assumed that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously."
::= { jnxPppLcp 3 }
-- ////////////////////////////////////////////////////////////////////////////
-- PPP Security
-- This section defines objects used to manage the PPP Security
-- functionality of PPP.
-- ////////////////////////////////////////////////////////////////////////////
-- No objects are currently defined.
-- ////////////////////////////////////////////////////////////////////////////
-- PPP IP NCP
-- This section defines objects used to manage the PPP Network Control Protocol
-- for IP protocol operation (IPCP).
-- /////////////////////////////////////////////////////////////////////////////
-- The PPP IP Table
jnxPppIpTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppIpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing the IP parameters for the local PPP entity."
::= { jnxPppIp 1 }
jnxPppIpEntry OBJECT-TYPE
SYNTAX JnxPppIpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IPCP status information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppIpTable 1 }
JnxPppIpEntry ::= SEQUENCE {
jnxPppIpServiceStatus INTEGER,
jnxPppIpTerminateReason INTEGER,
jnxPppIpTerminateNegFailOption INTEGER,
jnxPppIpLocalIpAddress IpAddress,
jnxPppIpRemoteIpAddress IpAddress,
jnxPppIpRemotePrimaryDnsAddress IpAddress,
jnxPppIpRemoteSecondaryDnsAddress IpAddress,
jnxPppIpRemotePrimaryWinsAddress IpAddress,
jnxPppIpRemoteSecondaryWinsAddress IpAddress,
jnxPppIpNetworkStatusIpcpRenegoTerminates Counter32}
jnxPppIpServiceStatus OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether IP protocol service is operating over this PPP link.
Service is established on this link through means outside this MIB."
::= { jnxPppIpEntry 1 }
jnxPppIpTerminateReason OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
noService(2),
admin(3),
linkDown(4),
peerTerminated(5),
peerRenegotiated(6),
maxRetriesExceeded(7),
negotiationFailure(8) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reason the IPCP link was terminated:
none None.
other Not specified.
noService No IP service configured on this PPP link.
admin Administratively disabled.
linkDown Underlying link is down.
peerTerminated Peer initiated termination.
peerRenegotiated Peer initiated renegotiation.
maxRetriesExceeded Maximum number of config retries exceeded.
negotiationFailure Failed to negotiate IPCP option. See
jnxPppIpTerminateNegFailOption."
::= { jnxPppIpEntry 2 }
jnxPppIpTerminateNegFailOption OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
localIpAddress(2),
remoteIpAddress(3),
remotePrimaryDnsAddress(4),
remoteSecondaryDnsAddress(5),
remotePrimaryWinsAddress(6),
remoteSecondaryWinsAddress(7),
localIpAddressMask(8),
remoteIpAddressMask(9) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reports the PPP IPCP option for which negotiation failed, when
jnxPppIpTerminateReason has the value 'negotiationFailure'."
::= { jnxPppIpEntry 3 }
jnxPppIpLocalIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IP Address used by the local side."
::= { jnxPppIpEntry 4 }
jnxPppIpRemoteIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IP Address used by the remote side."
::= { jnxPppIpEntry 5 }
jnxPppIpRemotePrimaryDnsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Primary DNS server used by the remote side."
::= { jnxPppIpEntry 6 }
jnxPppIpRemoteSecondaryDnsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Secondary DNS server used by the remote side."
::= { jnxPppIpEntry 7 }
jnxPppIpRemotePrimaryWinsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Primary WINS server used by the remote side."
::= { jnxPppIpEntry 8 }
jnxPppIpRemoteSecondaryWinsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Secondary WINS server used by the remote side."
::= { jnxPppIpEntry 9 }
jnxPppIpNetworkStatusIpcpRenegoTerminates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times ipcp terminated due to peer exceeding max
renegotiation attempts."
::= { jnxPppIpEntry 10 }
--
-- The PPP IP Config Table
--
jnxPppIpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppIpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing the IP parameters for the local PPP entity."
::= { jnxPppIp 2 }
jnxPppIpConfigEntry OBJECT-TYPE
SYNTAX JnxPppIpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IPCP configuration information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppIpConfigTable 1 }
JnxPppIpConfigEntry ::= SEQUENCE {
jnxPppIpConfigPeerDnsPriority INTEGER,
jnxPppIpConfigPeerWinsPriority INTEGER,
jnxPppIpConfigIpcpNetmask INTEGER,
jnxPppIpConfigInitiateIp INTEGER,
jnxPppIpConfigMaxIpcpRenegotiation Integer32,
jnxPppIpConfigPromptIpcpDnsOption INTEGER,
jnxPppIpConfigIpcpLockout INTEGER}
jnxPppIpConfigPeerDnsPriority OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When enabled, allows peer's DNS address to prevail in the event of a
negotiation conflict; when disabled, the local PPP interface's DNS
address prevails."
::= { jnxPppIpConfigEntry 1 }
jnxPppIpConfigPeerWinsPriority OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When enabled, allows peer's WINS address to prevail in the event of a
negotiation conflict; when disabled, the local PPP interface's WINS
address prevails."
::= { jnxPppIpConfigEntry 2 }
jnxPppIpConfigIpcpNetmask OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables the negotiation of the IPCP option netmask (0x90) during
IPCP negotiation."
DEFVAL { disable }
::= { jnxPppIpConfigEntry 3 }
jnxPppIpConfigInitiateIp OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables the initiation of negotiation of the IPCP."
DEFVAL { disable }
::= { jnxPppIpConfigEntry 4 }
jnxPppIpConfigMaxIpcpRenegotiation OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of allowed ipcp renegotiation attempts from peer."
DEFVAL { 30 }
::= { jnxPppIpConfigEntry 5 }
jnxPppIpConfigPromptIpcpDnsOption OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Control prompting of IPCP DNS option to remote peer."
DEFVAL { disable }
::= { jnxPppIpConfigEntry 6 }
jnxPppIpConfigIpcpLockout OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables IPCP lockout. It determines whether this NCP can be negotiated
when the interface is already running a different NCP. On enabling
this option, the IPCP negotiation will be blocked after a different
NCP service is up and waited for 10 seconds for IPCP initiation
from peer."
DEFVAL { disable }
::= { jnxPppIpConfigEntry 7 }
-- /////////////////////////////////////////////////////////////////////////////
-- PPP OSI NCP
-- This section defines objects used to manage the PPP Network Control Protocol
-- for OSI protocol operation (OSICP). The IETF does not define a standard MIB
-- for managing an OSI NCP. For consistency, this MIB follows the model of
--- RFC1473 for IP NCP:
-- A status table reports the condition of the NCP state machine, and the outcome
--of option parameter negotiation (if any) when the OperStatus object has the
-- value 'opened(1)'; a configuration table provides administrative control over
-- the NCP state machine, and permits configuration of proposed option parameter
-- values (if any) to be used during NCP negotiation.
-- /////////////////////////////////////////////////////////////////////////////
-- PPP OSI Status Table
--
jnxPppOsiTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppOsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing the OSI parameters for the local PPP entity."
::= { jnxPppOsi 1 }
jnxPppOsiEntry OBJECT-TYPE
SYNTAX JnxPppOsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"OSICP status information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppOsiTable 1 }
JnxPppOsiEntry ::= SEQUENCE {
jnxPppOsiServiceStatus INTEGER,
jnxPppOsiOperStatus INTEGER,
jnxPppOsiTerminateReason INTEGER,
jnxPppOsiTerminateNegFailOption INTEGER,
jnxPppOsiLocalAlignNpdu INTEGER,
jnxPppOsiRemoteAlignNpdu INTEGER }
jnxPppOsiServiceStatus OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether OSI protocol service is operating over this PPP link.
Service is established on this link through means outside this MIB."
::= { jnxPppOsiEntry 1 }
jnxPppOsiOperStatus OBJECT-TYPE
SYNTAX INTEGER {
opened(1),
notOpened(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational status of the OSI network protocol. If the value of
this object is up then the finite state machine for the OSI network
protocol has reached the Opened state."
::= { jnxPppOsiEntry 2 }
jnxPppOsiTerminateReason OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
noService(2),
admin(3),
linkDown(4),
peerTerminated(5),
peerRenegotiated(6),
maxRetriesExceeded(7),
negotiationFailure(8) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reason the OSICP link was terminated:
none None.
other Not specified.
noService No OSI service configured on this PPP link.
admin Administratively disabled.
linkDown Underlying link is down.
peerTerminated Peer initiated termination.
peerRenegotiated Peer initiated renegotiation.
maxRetriesExceeded Maximum number of config retries exceeded.
negotiationFailure Failed to negotiate IPCP option. See
jnxPppOsiTerminateNegFailOption."
::= { jnxPppOsiEntry 3 }
jnxPppOsiTerminateNegFailOption OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
localAlignNpdu(2),
remoteAlignNpdu(3) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reports the PPP OSICP option for which negotiation failed, when
jnxPppOsiTerminateReason has the value 'negotiationFailure'."
::= { jnxPppOsiEntry 4 }
jnxPppOsiLocalAlignNpdu OBJECT-TYPE
SYNTAX INTEGER {
none(0),
oneModulo4(1),
twoModulo4(2),
threeModulo4(3),
fourModulo4(4),
even(254),
odd(255) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Local alignment of network PDU:
none No alignment specified.
oneModulo4 Alignment on first octet (out of four).
twoModulo4 Alignment on second octet (out of four).
threeModulo4 Alignment on third octet (out of four).
fourModulo4 Alignment on fourth octet (out of four).
even Alignment on even-octet boundary.
odd Alignment on odd-octet boundary."
::= { jnxPppOsiEntry 5 }
jnxPppOsiRemoteAlignNpdu OBJECT-TYPE
SYNTAX INTEGER {
none(0),
oneModulo4(1),
twoModulo4(2),
threeModulo4(3),
fourModulo4(4),
even(254),
odd(255) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote alignment of network PDU.
none No alignment specified.
oneModulo4 Alignment on first octet (out of four).
twoModulo4 Alignment on second octet (out of four).
threeModulo4 Alignment on third octet (out of four).
fourModulo4 Alignment on fourth octet (out of four).
even Alignment on even-octet boundary.
odd Alignment on odd-octet boundary."
::= { jnxPppOsiEntry 6 }
--
-- The PPP OSI Configuration Table
--
jnxPppOsiConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppOsiConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing configuration variables for the OSICP for the
local PPP entity."
::= { jnxPppOsi 2 }
jnxPppOsiConfigEntry OBJECT-TYPE
SYNTAX JnxPppOsiConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"OSICP information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppOsiConfigTable 1 }
JnxPppOsiConfigEntry ::= SEQUENCE {
jnxPppOsiConfigAdminStatus INTEGER }
jnxPppOsiConfigAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
open(1),
close(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The immediate desired status of the OSI network protocol.
Setting this object to open will inject an administrative open event
into the OSI network protocol's finite state machine. Setting this
object to close will inject an administrative close event into the
OSI network protocol's finite state machine."
::= { jnxPppOsiConfigEntry 1 }
-- /////////////////////////////////////////////////////////////////////////////
-- PPP Session
-- This section defines objects used to manage the PPP sessions.
-- The jnxPppSessionTable provides status of each PPP session.
-- /////////////////////////////////////////////////////////////////////////////
-- The PPP Session Table
--
jnxPppSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for PPP interfaces present in the system."
::= { jnxPppSession 1 }
jnxPppSessionEntry OBJECT-TYPE
SYNTAX JnxPppSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of a PPP interface."
INDEX { ifIndex }
::= { jnxPppSessionTable 1 }
JnxPppSessionEntry ::= SEQUENCE {
jnxPppSessionGrant TruthValue,
jnxPppSessionTerminateReason INTEGER,
jnxPppSessionStartTime TimeTicks,
jnxPppSessionInOctets Counter32,
jnxPppSessionOutOctets Counter32,
jnxPppSessionInPackets Counter32,
jnxPppSessionOutPackets Counter32,
jnxPppSessionSessionTimeout Integer32,
jnxPppSessionInactivityTimeout Integer32,
jnxPppSessionAccountingInterval Integer32,
jnxPppSessionRemoteIpAddress IpAddress,
jnxPppSessionRemotePrimaryDnsAddress IpAddress,
jnxPppSessionRemoteSecondaryDnsAddress IpAddress,
jnxPppSessionRemotePrimaryWinsAddress IpAddress,
jnxPppSessionRemoteSecondaryWinsAddress IpAddress,
jnxPppSessionRemoteIpv6AddressIfIdentifier Ipv6AddressIfIdentifier,
jnxPppSessionInhibitIp INTEGER,
jnxPppSessionInhibitIpv6 INTEGER,
jnxPppSessionInOctets64 Counter64,
jnxPppSessionOutOctets64 Counter64,
jnxPppSessionInPackets64 Counter64,
jnxPppSessionOutPackets64 Counter64}
jnxPppSessionGrant OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a session has been granted via the authentication
mechanism."
::= { jnxPppSessionEntry 1 }
jnxPppSessionTerminateReason OBJECT-TYPE
SYNTAX INTEGER {
none(0),
unknown(1),
userRequest(2),
keepaliveFailure(3),
sessionTimeout(4),
inactivityTimeout(5),
adminDisable(6),
lowerLayerDown(7),
noUpperInterface(8),
deny(9),
noHardware(10),
noResources(11),
noInterface(12),
challengeTimeout(13),
requestTimeout(14),
authenticatorTimeout(15),
addressLeaseExpired(16),
adminLogout(17),
tunnelFailed(18) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The reason the session was terminated."
::= { jnxPppSessionEntry 2 }
jnxPppSessionStartTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this session last became active."
::= { jnxPppSessionEntry 3 }
jnxPppSessionInOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of octets received since this session last became active, as
denoted by jnxPppSessionStartTime. This has been deprecated and
replaced by jnxPppSessionInOctets64"
::= { jnxPppSessionEntry 4 }
jnxPppSessionOutOctets OBJECT-TYPE
SYNTAX Counter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of octets sent since this session last became active, as
denoted by jnxPppSessionStartTime. This has been deprecated and
replaced by jnxPppSessionOutOctets64"
::= { jnxPppSessionEntry 5 }
jnxPppSessionInPackets OBJECT-TYPE
SYNTAX Counter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of packets received since this session last became active, as
denoted by jnxPppSessionStartTime. This has been deprecated and
replaced by jnxPppSessionInPackets64"
::= { jnxPppSessionEntry 6 }
jnxPppSessionOutPackets OBJECT-TYPE
SYNTAX Counter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of packets sent since this session last became active, as
denoted by jnxPppSessionStartTime. This has been deprecated and
replaced by jnxPppSessionOutPackets64"
::= { jnxPppSessionEntry 7 }
jnxPppSessionSessionTimeout OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum duration for the session, after which the session terminates
automatically."
::= { jnxPppSessionEntry 8 }
jnxPppSessionInactivityTimeout OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum inactivity duration for the session, after which the session
terminates automatically."
::= { jnxPppSessionEntry 9 }
jnxPppSessionAccountingInterval OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interval that must elapse between generation of accounting records
for this session."
::= { jnxPppSessionEntry 10 }
jnxPppSessionRemoteIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote IP address, obtained from the authentication service, to be
used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 11 }
jnxPppSessionRemotePrimaryDnsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote primary DNS IP address, obtained from the authentication
service, to be used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 12 }
jnxPppSessionRemoteSecondaryDnsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote secondary DNS IP address, obtained from the authentication
service, to be used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 13 }
jnxPppSessionRemotePrimaryWinsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote primary WINS IP address, obtained from the authentication
service, to be used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 14 }
jnxPppSessionRemoteSecondaryWinsAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remote secondary WINS IP address, obtained from the authentication
service, to be used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 15 }
jnxPppSessionRemoteIpv6AddressIfIdentifier OBJECT-TYPE
SYNTAX Ipv6AddressIfIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IPV6 Address Interface Identifier obtained from the authentication
service, to be used during IPCP negotiation with the remote side."
::= { jnxPppSessionEntry 16 }
jnxPppSessionInhibitIp OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a session has had its IP service inhibited by the
authentication mechanism."
::= { jnxPppSessionEntry 17 }
jnxPppSessionInhibitIpv6 OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a session has had its IPv6 service inhibited by the
authentication mechanism."
::= { jnxPppSessionEntry 18 }
jnxPppSessionInOctets64 OBJECT-TYPE
SYNTAX Counter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of octets received since this session last became active, as
denoted by jnxPppSessionStartTime."
::= { jnxPppSessionEntry 19 }
jnxPppSessionOutOctets64 OBJECT-TYPE
SYNTAX Counter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of octets sent since this session last became active, as
denoted by jnxPppSessionStartTime."
::= { jnxPppSessionEntry 20 }
jnxPppSessionInPackets64 OBJECT-TYPE
SYNTAX Counter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets received since this session last became active, as
denoted by jnxPppSessionStartTime."
::= { jnxPppSessionEntry 21 }
jnxPppSessionOutPackets64 OBJECT-TYPE
SYNTAX Counter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets sent since this session last became active, as
denoted by jnxPppSessionStartTime."
::= { jnxPppSessionEntry 22 }
-- /////////////////////////////////////////////////////////////////////////////
-- Multi-Link PPP (MLPPP)
-- This section defines objects used to manage the MLPPP.
-- /////////////////////////////////////////////////////////////////////////////
--
-- The MLPPP BundleTable
--
jnxPppMlPppBundleTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppMlPppBundleEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for MLPPP bundles present in the system."
::= { jnxPppMlPpp 1 }
jnxPppMlPppBundleEntry OBJECT-TYPE
SYNTAX JnxPppMlPppBundleEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of a MLPPP bundle."
INDEX { jnxPppMlPppBundleName }
::= { jnxPppMlPppBundleTable 1 }
JnxPppMlPppBundleEntry ::= SEQUENCE {
jnxPppMlPppBundleName JnxPppMlPppBundleName,
jnxPppMlPppBundleRowStatus RowStatus,
jnxPppMlPppBundleNetworkIfIndex InterfaceIndex }
jnxPppMlPppBundleName OBJECT-TYPE
SYNTAX JnxPppMlPppBundleName
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The administrative name of the MLPPP bundle associated with this
MLPPP network interface."
::= { jnxPppMlPppBundleEntry 1 }
jnxPppMlPppBundleRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The rowStatus for this entry. The following sets are supported
with read-create maximum access:
createAndGo(4),
destroy(6)
The following values can be read from this object:
active(1) "
::= { jnxPppMlPppBundleEntry 2 }
jnxPppMlPppBundleNetworkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of this MLPPP network interface. It is a valid ifIndex
even if there is no corresponding network interface instance in
the jnxPppMlPppLinkConfigTable."
::= { jnxPppMlPppBundleEntry 3 }
--
-- IfIndex selection for creating new MLPPP Link interfaces in
-- jnxPppLinkConfigTable.
--
-- NOTE: This object is placed after jnxPppLinkConfigTable so that jnxPppLinkStatusTable and jnxPppLinkConfigTable have the same relative MIB node positions below the jnxPppLcp node (jnxPppLcp.1 and jnxPppLcp.2, respectively) as their counterpart Status and Config tables in RFC1471.
jnxPppMlPppNextLinkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Coordinate ifIndex value allocation for entries in
jnxPppMlPppLinkConfigTable. A GET of this object returns the next
available ifIndex value to be used to create an entry in the
associated interface table; or zero, if no valid ifIndex value is
available. This object also returns a value of zero when it is the
lexicographic successor of a varbind presented in an SNMP GETNEXT
or GETBULK request, for which circumstance it is assumed that ifIndex
allocation is unintended. Successive GETs will typically return
different values, thus avoiding collisions among cooperating management
clients seeking to create table entries simultaneously."
::= { jnxPppMlPpp 2 }
--
-- The MLPPP Link Configuration Table
--
jnxPppMlPppLinkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppMlPppLinkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for MLPPP interfaces present in the system."
::= { jnxPppMlPpp 3 }
jnxPppMlPppLinkConfigEntry OBJECT-TYPE
SYNTAX JnxPppMlPppLinkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of MLPPP interface.
With read-create maximum access,creating/deleting entries in this
table causes corresponding entries for be created/deleted in
ifTable/ifXTable/jnxIfTable."
INDEX { jnxPppMlPppLinkConfigIfIndex }
::= { jnxPppMlPppLinkConfigTable 1 }
JnxPppMlPppLinkConfigEntry ::= SEQUENCE {
jnxPppMlPppLinkConfigIfIndex InterfaceIndex,
jnxPppMlPppLinkConfigLowerIfIndex InterfaceIndexOrZero,
jnxPppMlPppLinkConfigKeepalive Integer32,
jnxPppMlPppLinkConfigAuthentication JnxPppAuthentication,
jnxPppMlPppLinkConfigMaxAuthenRetries Integer32,
jnxPppMlPppLinkConfigRowStatus RowStatus,
jnxPppMlPppLinkConfigAaaProfile OCTET STRING,
jnxPppMlPppLinkConfigChapMinChallengeLength Integer32,
jnxPppMlPppLinkConfigChapMaxChallengeLength Integer32,
jnxPppMlPppLinkConfigPassiveMode INTEGER,
jnxPppMlPppLinkConfigAuthenticatorLogicalSystem OCTET STRING,
jnxPppMlPppLinkConfigAuthenticatorRoutingInstance OCTET STRING,
jnxPppMlPppLinkConfigFragmentation INTEGER,
jnxPppMlPppLinkConfigReassembly INTEGER,
jnxPppMlPppLinkConfigMaxReceiveReconstructedUnit Integer32,
jnxPppMlPppLinkConfigFragmentSize Integer32,
jnxPppMlPppLinkConfigHashLinkSelection INTEGER,
jnxPppMlPppLinkConfigAuthentication2 JnxNibbleConfig,
jnxPppMlPppLinkConfigIgnoreMagicNumberMismatch INTEGER,
jnxPppMlPppLinkConfigMultilinkMulticlass INTEGER,
jnxPppMlPppLinkConfigMultilinkMaxMultiClasses INTEGER}
jnxPppMlPppLinkConfigIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the MLPPP interface. When creating entries in this
table, suitable values for this object are determined by reading
jnxPppMlPppNextLinkIfIndex."
::= { jnxPppMlPppLinkConfigEntry 1 }
jnxPppMlPppLinkConfigLowerIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of an interface over which this PPP interface is to be
layered. A value of zero indicates no layering. An implementation
may choose to require that a non-zero value be configured at entry
creation."
::= { jnxPppMlPppLinkConfigEntry 2 }
jnxPppMlPppLinkConfigKeepalive OBJECT-TYPE
SYNTAX Integer32 (0|10..64800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Keepalive interval in seconds. A value of zero disables keepalive.
Keepalive is performed using LCP Echo."
DEFVAL { 30 }
::= { jnxPppMlPppLinkConfigEntry 4 }
jnxPppMlPppLinkConfigAuthentication OBJECT-TYPE
SYNTAX JnxPppAuthentication
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Specifies the type(s) of authentication, if any, to be
negotiated with the peer:
none No authentication is negotiated.
pap PAP negotiation only.
chap CHAP negotiation only.
papChap PAP negotiation is attempted first; if fails, attempt CHAP.
chapPap CHAP negotiation is attempted first; if fails, attempt PAP.
If authentication negotiation is not supported for this MLPPP interface,
then any attempt to explicitely set this object will result in a
notWritable error and it will be implicitily set to the DEFVAL on
row creation.
This object returns a none (0) value on the get operation.
New object jnxPppMlPppLinkConfigAuthentication2 will reflect the configured
values. Setting this object along with the jnxPppMlPppLinkConfigAuthentication2
object will return an inconsistentValue error."
DEFVAL { none }
::= { jnxPppMlPppLinkConfigEntry 5 }
jnxPppMlPppLinkConfigMaxAuthenRetries OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of authentication retries permitted, in addition to a
failed initial attempt. If all retries fail, the link is reset."
DEFVAL { 0 }
::= { jnxPppMlPppLinkConfigEntry 6 }
jnxPppMlPppLinkConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Controls creation/deletion of entries in this table with read-carete
maximum access,according to the RowStatus textual convention,
constrained to support the following values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
jnxPppMlPppLinkConfigRowStatus
jnxPppMlPppLinkConfigLowerIfIndex
In addition, when creating an entry the following conditions must hold:
A value for jnxPppMlPppLinkConfigIndex must have been
determined previously, by reading jnxPppMlPppNextIfIndex.
The interface identified by jnxPppMlPppLinkConfigLowerIfIndex
must exist.
A corresponding entry in ifTable/ifXTable/jnxIfTable is
created/destroyed as a result of creating/destroying an entry in
this table.
The following values can be read from this object:
active(1) "
::= { jnxPppMlPppLinkConfigEntry 7 }
jnxPppMlPppLinkConfigAaaProfile OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the AAA profile to be used for authentication on the
PPP interface.Setting this object statically binds the AAA profile
with the PPP interface. If this object is not explicitly set or it
is set to null string, then this object is ignored. On a Set operation,
if the value of this object is not null and does not correspond to an
existin AAA profile, then an inconsistentValue error is returned."
::= { jnxPppMlPppLinkConfigEntry 8 }
jnxPppMlPppLinkConfigChapMinChallengeLength OBJECT-TYPE
SYNTAX Integer32 (8..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum value of the CHAP authenticator challenge length value.
This value is never allowed to be set to a value greater than
jnxPppMlPppLinkConfigChapMaxChallengeLength."
DEFVAL { 16 }
::= { jnxPppMlPppLinkConfigEntry 9 }
jnxPppMlPppLinkConfigChapMaxChallengeLength OBJECT-TYPE
SYNTAX Integer32 (8..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum value of the CHAP authenticator challenge length value."
DEFVAL { 32 }
::= { jnxPppMlPppLinkConfigEntry 10 }
jnxPppMlPppLinkConfigPassiveMode OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When enabled, LCP state machine is forced into passive mode on lower
layer UP message. It adds compatibility with slow and buggy clients."
DEFVAL { disable }
::= { jnxPppMlPppLinkConfigEntry 11 }
jnxPppMlPppLinkConfigAuthenticatorLogicalSystem OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the Logical System (Jnxper-ROUTER-MIB.jnxRouterName) to
be used for authentication on the PPP interface. Setting this object
statically binds the authenticating virtual router with the link interface.
With read-create maximum access, if this object is not explicitly set or
it is set to null string, then this object is ignored and the
virtual router used for authentication is determined by other means.
On a Set operation, if the value of this object is not null and does not
correspond to an existing virtual router, then an inconsistentValue
error is returned."
::= { jnxPppMlPppLinkConfigEntry 12 }
jnxPppMlPppLinkConfigAuthenticatorRoutingInstance OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the Routing Instance (Jnxper-ROUTER-MIB.jnxRouterName)
to be used for authentication on the PPP interface. Setting this
object statically binds the authenticating virtual router with the
link interface. With read-create maximum access, if this object is
not explicitly set or it is set to null string, then this object is
ignored and the virtual router used for authentication is
determined by other means. On a Set operation, if the value of
this object is not null and does not correspond to an existing
virtual router, then an inconsistentValue error is returned."
::= { jnxPppMlPppLinkConfigEntry 13 }
jnxPppMlPppLinkConfigFragmentation OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables MLPPP fragmentation.With read-create maximum access,
changing this object has an effect when the link is next restarted."
DEFVAL { disable }
::= { jnxPppMlPppLinkConfigEntry 14 }
jnxPppMlPppLinkConfigReassembly OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables MLPPP reassembly. With read-create maximum access,
changing this object has an effect when the link is next restarted."
DEFVAL { disable }
::= { jnxPppMlPppLinkConfigEntry 15 }
jnxPppMlPppLinkConfigMaxReceiveReconstructedUnit OBJECT-TYPE
SYNTAX Integer32 (1|64..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Maximum Receive Reconstructed Unit (MRRU) that the local
PPP entity will advertise to the remote entity. If the value of
this variable is 1, then the MRRU is set to the local MRU value.
With read-create maximum access, changing this object has an effect
when the link is next restarted."
DEFVAL { 1 }
::= { jnxPppMlPppLinkConfigEntry 16 }
jnxPppMlPppLinkConfigFragmentSize OBJECT-TYPE
SYNTAX Integer32 (1|128..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of fragments transmitted by the local PPP entity.
If the value of this variable is 1, then the fragment size is set to
the link's MTU value. With read-create maximum access,
changing this object has an effect when the link is next restarted."
DEFVAL { 1 }
::= { jnxPppMlPppLinkConfigEntry 17 }
jnxPppMlPppLinkConfigHashLinkSelection OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables MLPPP hash-based link selection for non-best-effort traffic.
With read-create maximum access,changing this object has an effect
when the link is next restarted."
DEFVAL { disable }
::= { jnxPppMlPppLinkConfigEntry 18 }
jnxPppMlPppLinkConfigAuthentication2 OBJECT-TYPE
SYNTAX JnxNibbleConfig
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A configuration variable comprised of nibbles i.e. 4 bits, such
that a client can supply a list of 0 to 8 selections. The least
significant nibble is the first value of the list, and the most
significant nibble is the last value. The value in each field
ranges from 0 to 15, however the first nibble with value 0 indicates
the end of the list. Repetition of values is not allowed.
Segregation of values is not allowed.
Valid Values are:
none - 0
pap - 1
chap - 2
eap - 3
Example valid encoding:
0x00000321
0x00000012
Not a valid encoding:
0x00000121
0x01002001
If authentication negotiation is not supported for this PPP interface
and With read-create maximum access, then any attempt to explicitly
set this object will result in a notWritable error and it will be
implicitly set to the DEFVAL on row creation. Setting this object to
null will set jnxPppMlPppLinkConfigAuthenticatorVirtualRouter object
to an empty string.Setting this object along with the
jnxPppMlPppLinkConfigAuthentication object will return an i
nconsistentValue error."
DEFVAL { 0 }
::= { jnxPppMlPppLinkConfigEntry 19 }
jnxPppMlPppLinkConfigIgnoreMagicNumberMismatch OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ignore magic number mismatch option of the PPP interface determines
the action to be taken, when the peer has not negotiated any value yet
sent null or invalid magic number in the LCP echo packets. The two
actions that can be configured are:
1) Ignore the mismatch and retain connection
2) Disallow the mismatch and terminate connection"
DEFVAL { disable }
::= { jnxPppMlPppLinkConfigEntry 20 }
jnxPppMlPppLinkConfigMultilinkMulticlass OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables Multiclass Multilink PPP (MCML). With read-create maximum
access,changing this object has an effect when the link is next
restarted."
DEFVAL {disable}
::= { jnxPppMlPppLinkConfigEntry 21 }
jnxPppMlPppLinkConfigMultilinkMaxMultiClasses OBJECT-TYPE
SYNTAX INTEGER (0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of MCML classes to be negotiated.With read-create
maximum access,changing this object has an effect when the link
is next restarted."
DEFVAL {0}
::= { jnxPppMlPppLinkConfigEntry 22 }
jnxPppMlPppNextNetworkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Coordinate ifIndex value allocation for entries in
jnxPppMlPppNetworkConfigTable. A GET of this object returns the next
available ifIndex value to be used to create an entry in the associated
interface table; or zero, if no valid ifIndex value is available.
This object also returns a value of zero when it is the lexicographic
successor of a varbind presented in an SNMP GETNEXT or GETBULK request,
for which circumstance it is assumed that ifIndex allocation
is unintended. Successive GETs will typically return different values,
thus avoiding collisions among cooperating management clients seeking
to create table entries simultaneously."
::= { jnxPppMlPpp 4 }
--
-- The MLPPP Network Configuration Table
--
jnxPppMlPppNetworkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppMlPppNetworkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for MLPPP network interfaces
present in the system."
::= { jnxPppMlPpp 5 }
jnxPppMlPppNetworkConfigEntry OBJECT-TYPE
SYNTAX JnxPppMlPppNetworkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the characteristics of MLPPP interface.
With read-create maximum access,creating/deleting entries in
this table causes corresponding entries for be created/deleted
in ifTable/ifXTable/jnxIfTable."
INDEX { jnxPppMlPppNetworkConfigIfIndex }
::= { jnxPppMlPppNetworkConfigTable 1 }
JnxPppMlPppNetworkConfigEntry ::= SEQUENCE {
jnxPppMlPppNetworkConfigIfIndex InterfaceIndex,
jnxPppMlPppNetworkConfigLowerIfIndex InterfaceIndex,
jnxPppMlPppNetworkBundleName JnxPppMlPppBundleName,
jnxPppMlPppNetworkRowStatus RowStatus }
jnxPppMlPppNetworkConfigIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the MLPPP network interface. When creating entries
in this table, suitable values for this object are determined by
reading jnxPppMlPppNextNetworkIfIndex."
::= { jnxPppMlPppNetworkConfigEntry 1 }
jnxPppMlPppNetworkConfigLowerIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of a PPP link interface over which this PPP network
interface is to be layered. On sets, the value of this object must
equal on of the previously created PPP link interfaces created in
the jnxPppMlPppLinkConfigTable. On gets, the value of this object
is the lexicographically least PPP link interface in a potential
bundle of PPP link interfaces."
::= { jnxPppMlPppNetworkConfigEntry 2 }
jnxPppMlPppNetworkBundleName OBJECT-TYPE
SYNTAX JnxPppMlPppBundleName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The MLPPP bundle name administratively assigned."
::= { jnxPppMlPppNetworkConfigEntry 3 }
jnxPppMlPppNetworkRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Controls creation/deletion of entries in this table with read-create
maximum access , according to the RowStatus textual convention,
constrained to support the following values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
jnxPppMlPppNetworkConfigLowerIfIndex
jnxPppMlPppNetworkBundleName
jnxPppMlPppNetworkConfigRowStatus
In addition, when creating an entry the following conditions must hold:
A value for jnxPppMlPppNetworkConfigIndex must have been determined
previously, by reading jnxPppMlPppNextNetworkIfIndex. The
interface identified by jnxPppMlPppNetworkConfigLowerIfInde must
exist by a creation request to the jnxPppMlPppLinkConfigTable.
The bundleName specified in jnxPppMlPppNetworkBundleName must have
been created first in the jnxPppMlPppBundleTable. A corresponding
entry in ifTable/ifXTable/jnxIfTable is created/destroyed as a
result of creating/destroying an entry in this table.
The following values can be read from this object:
active(1) "
::= { jnxPppMlPppNetworkConfigEntry 4 }
--
-- The MLPPP Link Bind Table
--
jnxPppMlPppLinkBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppMlPppLinkBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains entries for MLPPP Link interface to MLPPP
network interfaces bindings."
::= { jnxPppMlPpp 6 }
jnxPppMlPppLinkBindEntry OBJECT-TYPE
SYNTAX JnxPppMlPppLinkBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes the MLPPP link interface to MLPPP network
interface bindings."
INDEX { jnxPppMlPppBindNetworkIfIndex,
jnxPppMlPppBindLinkIfIndex }
::= { jnxPppMlPppLinkBindTable 1 }
JnxPppMlPppLinkBindEntry ::= SEQUENCE {
jnxPppMlPppBindNetworkIfIndex InterfaceIndex,
jnxPppMlPppBindLinkIfIndex InterfaceIndex,
jnxPppMlPppBindRowStatus RowStatus }
jnxPppMlPppBindNetworkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the MLPPP network interface."
::= { jnxPppMlPppLinkBindEntry 1 }
jnxPppMlPppBindLinkIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of a MLPPP link interface bound by the MLPPP network
interface defined by jnxPppMlPppBindNetworkIfIndex."
::= { jnxPppMlPppLinkBindEntry 2 }
jnxPppMlPppBindRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Controls creation/deletion of entries in this table with read-create
maximum access, according to the RowStatus textual convention,
constrained to support the following values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST
be explicitly configured:
jnxPppMlPppBindRowStatus
In addition, when creating an entry the following conditions must hold:
The interfaces identified by jnxPppMlPppBindNetworkIfIndex and
jnxPppMlPppBindLinkIfIndex must be created in the
jnxPppMlPppNetworkConfigTable and jnxPppMlPppLinkConfigTable
respectively. A MLPPP bundle must be associated with the
jnxPppMlPppNetworkIfIndex and exist in the jnxPppMibPppBundleTable.
A corresponding entry in ifStackTable is created/destroyed as a result
of creating/destroying an entry in this table.
The following values can be read from this object:
active(1) "
::= { jnxPppMlPppLinkBindEntry 3 }
-- /////////////////////////////////////////////////////////////////////////////
-- PPP Interface Summary Counts
-- /////////////////////////////////////////////////////////////////////////////
jnxPppSummaryPppInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces configured in the system."
::= { jnxPppSummary 1 }
jnxPppSummaryPppIpNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number IP NCPs configured in the system."
::= { jnxPppSummary 2 }
jnxPppSummaryPppOsiNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs configured in the system."
::= { jnxPppSummary 3 }
jnxPppSummaryPppIfAdminUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system that are
administratively configured to up(1)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 4 }
jnxPppSummaryPppIfAdminDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system that are
administrateively configued to down(2)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 5 }
jnxPppSummaryPppIfOperUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system with an
operational state of up(1)."
REFERENCE
"IF-MIB.ifOperstatus"
::= { jnxPppSummary 7 }
jnxPppSummaryPppIfOperDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system with an
operational state of down(2)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 8 }
jnxPppSummaryPppIfOperDormant OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system with an
operational state of dormant(5)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 9 }
jnxPppSummaryPppIfNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system with an
operational state of notPresent(6)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 10 }
jnxPppSummaryPppIfLowerLayerDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP interfaces in the system with an
operational state of lowerLayerDown(7)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 11 }
jnxPppSummaryPppIpNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an
operational state of opened(1)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 12 }
jnxPppSummaryPppIpNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an
operational state of not-opened(2)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 13 }
jnxPppSummaryPppOsiNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an
operational state of opened."
::= { jnxPppSummary 14 }
jnxPppSummaryPppOsiNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an
operational state of closed."
::= { jnxPppSummary 15 }
jnxPppSummaryPppIfLastChangeTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime at the time of the last PPP interface
creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value. "
::= { jnxPppSummary 16 }
jnxPppSummaryPppLinkInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces configured in the system."
::= { jnxPppSummary 17 }
jnxPppSummaryPppLinkIfAdminUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system that are
administratively configured to up(1)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 18 }
jnxPppSummaryPppLinkIfAdminDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system that are
administrateively configued to down(2)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 19 }
jnxPppSummaryPppLinkIfOperUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system with an
operational state of up(1)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 20 }
jnxPppSummaryPppLinkIfOperDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system with an
operational state of down(2)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 21 }
jnxPppSummaryPppLinkIfOperDormant OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system with an
operational state of dormant(5)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 22 }
jnxPppSummaryPppLinkIfNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP link interfaces in the system with an
operational state of notPresent(6)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 23 }
jnxPppSummaryPppLinkIfLowerLayerDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP Link interfaces in the system with an
operational state of lowerLayerDown(7)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 24 }
jnxPppSummaryPppLinkIfLastChangeTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime at the time of the last PPP Link interface
creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value. "
::= { jnxPppSummary 25 }
jnxPppSummaryPppNetworkInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces configured in the system."
::= { jnxPppSummary 26 }
jnxPppSummaryPppNetworkIpNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number IP NCPs in the system configured on
PPP network interfaces."
::= { jnxPppSummary 27 }
jnxPppSummaryPppNetworkOsiNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system configured on
PPP network interfaces."
::= { jnxPppSummary 28 }
jnxPppSummaryPppNetworkIfAdminUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system that are
administratively configured to up(1)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 29 }
jnxPppSummaryPppNetworkIfAdminDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system that are
administrateively configued to down(2)."
REFERENCE
"IF-MIB.ifAdminStatus"
::= { jnxPppSummary 30 }
jnxPppSummaryPppNetworkIfOperUp OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system with an
operational state of up(1)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 31 }
jnxPppSummaryPppNetworkIfOperDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system with an
operational state of down(2)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 32 }
jnxPppSummaryPppNetworkIfOperDormant OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system with an
operational state of dormant(5)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 33 }
jnxPppSummaryPppNetworkIfNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system with an
operational state of notPresent(6)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 34 }
jnxPppSummaryPppNetworkIfLowerLayerDown OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP network interfaces in the system with an
operational state of lowerLayerDown(7)."
REFERENCE
"IF-MIB.ifOperStatus"
::= { jnxPppSummary 35 }
jnxPppSummaryPppNetworkIpNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an operational
state of opened(1)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 36 }
jnxPppSummaryPppNetworkIpNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an operational
state of not-opened(2)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 37 }
jnxPppSummaryPppNetworkOsiNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an operational
state of opened."
::= { jnxPppSummary 38 }
jnxPppSummaryPppNetworkOsiNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an operational
state of closed."
::= { jnxPppSummary 39 }
jnxPppSummaryPppNetworkIfLastChangeTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the sysUpTime at the time of the last PPP network
interface creation or deletion in the system. If the number of PPP
network interfaces has been unchanged since the last re-initialization
of the system, then this object contains a zero value. "
::= { jnxPppSummary 40 }
jnxPppSummaryPppIpv6NCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number IPv6 NCPs configured in the system."
::= { jnxPppSummary 41 }
jnxPppSummaryPppIpv6NcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPv6 NCPs in the system with an operational
state of opened(1)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 42 }
jnxPppSummaryPppIpv6NcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPv6 NCPs in the system with an operational
state of not-opened(2)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 43 }
jnxPppSummaryPppNetworkIpv6NCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number IPv6 NCPs configured in the system."
::= { jnxPppSummary 44 }
jnxPppSummaryPppNetworkIpv6NcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPv6 NCPs in the system with an operational
state of opened(1)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 45 }
jnxPppSummaryPppNetworkIpv6NcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPv6 NCPs in the system with an operational
state of not-opened(2)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 46 }
jnxPppSummaryPppStaticInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of static PPP interfaces configured in the system."
::= { jnxPppSummary 47 }
jnxPppSummaryPppMplsNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number MPLS NCPs configured in the system."
::= { jnxPppSummary 48 }
jnxPppSummaryPppIpAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system that are
administratively configured to open(1)."
::= { jnxPppSummary 49 }
jnxPppSummaryPppIpAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system that are
administratively configured to close(2)."
::= { jnxPppSummary 50 }
jnxPppSummaryPppIpv6AdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system that are
administratively configured to open(1)."
::= { jnxPppSummary 51 }
jnxPppSummaryPppIpv6AdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system that are
administratively configured to close(2)."
::= { jnxPppSummary 52 }
jnxPppSummaryPppOsiAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system that are
administratively configured to open(1)."
::= { jnxPppSummary 53 }
jnxPppSummaryPppOsiAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system that are
administratively configured to close(2)."
::= { jnxPppSummary 54 }
jnxPppSummaryPppMplsAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system that are
administratively configured to open(1)."
::= { jnxPppSummary 55 }
jnxPppSummaryPppMplsAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system that are
administratively configured to close(2)."
::= { jnxPppSummary 56 }
jnxPppSummaryPppIpNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an operational state
of notPresent(3)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 57}
jnxPppSummaryPppIpNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IP NCPs in the system with an operational
state of noResources(4)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 58 }
jnxPppSummaryPppIpv6NcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPV6 NCPs in the system with an operational state
of notPresent(3)."
::= { jnxPppSummary 59 }
jnxPppSummaryPppIpv6NcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP IPV6 NCPs in the system with an operational
state of noResources(4)."
::= { jnxPppSummary 60 }
jnxPppSummaryPppOsiNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an operational state
of notPresent(3)."
::= { jnxPppSummary 61 }
jnxPppSummaryPppOsiNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP OSI NCPs in the system with an operational
state of noResources(4)."
::= { jnxPppSummary 62 }
jnxPppSummaryPppMplsNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP MPLS NCPs in the system with an operational state
of opened(1)."
::= { jnxPppSummary 63 }
jnxPppSummaryPppMplsNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP MPLS NCPs in the system with an operational
state of not-opened(2)."
::= { jnxPppSummary 64 }
jnxPppSummaryPppMplsNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP MPLS NCPs in the system with an operational state
of notPresent(3)."
::= { jnxPppSummary 65 }
jnxPppSummaryPppMplsNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of PPP MPLS NCPs in the system with an operational
state of noResources(4)."
::= { jnxPppSummary 66 }
jnxPppSummaryPppLinkStaticInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of static PPP Link interfaces configured in the system."
::= { jnxPppSummary 67 }
jnxPppSummaryPppNetworkStaticInterfaceCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of static PPP network interfaces configured in the system."
::= { jnxPppSummary 68 }
jnxPppSummaryPppNetworkMplsNCPs OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces."
::= { jnxPppSummary 69 }
jnxPppSummaryPppNetworkIpAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system configured on PPP network
interfaces that are administratively configured to open(1)."
::= { jnxPppSummary 70 }
jnxPppSummaryPppNetworkIpAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system configured on PPP network
interfaces that are administratively configured to close(2)."
::= { jnxPppSummary 71 }
jnxPppSummaryPppNetworkIpv6AdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system configured on PPP network
interfaces that are administratively configured to open(1)."
::= { jnxPppSummary 72 }
jnxPppSummaryPppNetworkIpv6AdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system configured on PPP network
interfaces that are administratively configured to close(2)."
::= { jnxPppSummary 73 }
jnxPppSummaryPppNetworkOsiAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system configured on PPP network
interfaces that are administratively configured to open(1)."
::= { jnxPppSummary 74 }
jnxPppSummaryPppNetworkOsiAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system configured on PPP network
interfaces that are administratively configured to close(2)."
::= { jnxPppSummary 75 }
jnxPppSummaryPppNetworkMplsAdminOpen OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces that are administratively configured to open(1)."
::= { jnxPppSummary 76 }
jnxPppSummaryPppNetworkMplsAdminClose OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces that are administratively configured to close(2)."
::= { jnxPppSummary 77 }
jnxPppSummaryPppNetworkIpNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system configured on PPP network
interfaces with an operational state of notPresent(3)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 78 }
jnxPppSummaryPppNetworkIpNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP NCPs in the system configured on PPP network
interfaces with an operational state of noResources(4)."
REFERENCE
"PPP-IP-NCP-MIB.pppIpOperStatus"
::= { jnxPppSummary 79 }
jnxPppSummaryPppNetworkIpv6NcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system configured on PPP network
interfaces with an operational state of notPresent(3)."
::= { jnxPppSummary 80 }
jnxPppSummaryPppNetworkIpv6NcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IPV6 NCPs in the system configured on PPP network
interfaces with an operational state of noResources(4)."
::= { jnxPppSummary 81 }
jnxPppSummaryPppNetworkOsiNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system configured on PPP network
interfaces with an operational state of notPresent(3)."
::= { jnxPppSummary 82 }
jnxPppSummaryPppNetworkOsiNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of OSI NCPs in the system configured on PPP network
interfaces with an operational state of noResources(4)."
::= { jnxPppSummary 83 }
jnxPppSummaryPppNetworkMplsNcpOpened OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces with an operational state of opened(1)."
::= { jnxPppSummary 84 }
jnxPppSummaryPppNetworkMplsNcpClosed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces with an operational state of not-opened(2)."
::= { jnxPppSummary 85 }
jnxPppSummaryPppNetworkMplsNcpNotPresent OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces with an operational state of notPresent(3)."
::= { jnxPppSummary 86 }
jnxPppSummaryPppNetworkMplsNcpNoResources OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MPLS NCPs in the system configured on PPP network
interfaces with an operational state of noResources(4)."
::= { jnxPppSummary 87 }
-- ////////////////////////////////////////////////////////////////////////////
--
-- PPP IPv6 NCP
--
-- This section defines objects used to manage the PPP Network
-- Control Protocol for IPv6 protocol operation (IPV6CP).
--
-- ////////////////////////////////////////////////////////////////////////////
--
-- The PPP IPv6 Table
--
jnxPppIpv6Table OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppIpv6Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing the IPv6 parameters for the local PPP entity."
::= { jnxPppIpv6 1 }
jnxPppIpv6Entry OBJECT-TYPE
SYNTAX JnxPppIpv6Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IPV6CP status information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppIpv6Table 1 }
JnxPppIpv6Entry ::= SEQUENCE {
jnxPppIpv6ServiceStatus INTEGER,
jnxPppIpv6OperStatus INTEGER,
jnxPppIpv6TerminateReason INTEGER,
jnxPppIpv6TerminateNegFailOption INTEGER,
jnxPppIpv6LocalIpv6AddressIfIdentifier Ipv6AddressIfIdentifier,
jnxPppIpv6RemoteIpv6AddressIfIdentifier Ipv6AddressIfIdentifier,
jnxPppIpv6NetworkStatusIpv6cpRenegoTerminates Counter32}
jnxPppIpv6ServiceStatus OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether IPv6 protocol service is operating over this PPP
link. Service is established on this link through means outside this
MIB."
::= { jnxPppIpv6Entry 1 }
jnxPppIpv6OperStatus OBJECT-TYPE
SYNTAX INTEGER {
opened(1),
notOpened(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational status of the IPv6 network protocol. If the value of
this object is up then the finite state machine for the IPv6 network
protocol has reached the Opened state."
::= { jnxPppIpv6Entry 2 }
jnxPppIpv6TerminateReason OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
noService(2),
admin(3),
linkDown(4),
peerTerminated(5),
peerRenegotiated(6),
maxRetriesExceeded(7),
negotiationFailure(8) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reason the IPV6CP link was terminated:
none None.
other Not specified.
noService No IPv6 service configured on this PPP link.
admin Administratively disabled.
linkDown Underlying link is down.
peerTerminated Peer initiated termination.
peerRenegotiated Peer initiated renegotiation.
maxRetriesExceeded Maximum number of config retries exceeded.
negotiationFailure Failed to negotiate IPV6CP option. See
jnxPppIpv6TerminateNegFailOption."
::= { jnxPppIpv6Entry 3 }
jnxPppIpv6TerminateNegFailOption OBJECT-TYPE
SYNTAX INTEGER {
none(0),
other(1),
localIpv6AddressIfIdentifier(2),
remoteIpv6AddressIfIdentifier(3) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reports the PPP IPV6CP option for which negotiation failed, when
jnxPppIpv6TerminateReason has the value 'negotiationFailure'."
::= { jnxPppIpv6Entry 4 }
jnxPppIpv6LocalIpv6AddressIfIdentifier OBJECT-TYPE
SYNTAX Ipv6AddressIfIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IPv6 Address Interface Identifier used by the local side."
::= { jnxPppIpv6Entry 5 }
jnxPppIpv6RemoteIpv6AddressIfIdentifier OBJECT-TYPE
SYNTAX Ipv6AddressIfIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IPv6 Address Interface Identifier used by the remote side."
::= { jnxPppIpv6Entry 6 }
jnxPppIpv6NetworkStatusIpv6cpRenegoTerminates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times ipv6cp terminated due to peer exceeding max
renegotiation attempts."
::= { jnxPppIpv6Entry 7 }
--
-- The PPP IPv6 Config Table
--
jnxPppIpv6ConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPppIpv6ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table containing the IPv6 parameters for the local PPP entity."
::= { jnxPppIpv6 2 }
jnxPppIpv6ConfigEntry OBJECT-TYPE
SYNTAX JnxPppIpv6ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IPV6CP configuration information for a particular PPP link."
INDEX { ifIndex }
::= { jnxPppIpv6ConfigTable 1 }
JnxPppIpv6ConfigEntry ::= SEQUENCE {
jnxPppIpv6ConfigAdminStatus INTEGER,
jnxPppIpv6ConfigInitiateIpv6 INTEGER,
jnxPppIpv6ConfigMaxIpv6cpRenegotiation Integer32 }
jnxPppIpv6ConfigAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
open(1),
close(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The immediate desired status of the IPv6 network protocol. Setting
this object to open will inject an administrative open event into the
IPv6 network protocol's finite state machine. Setting this object to
close will inject an administrative close event into the IPv6 network
protocol's finite state machine."
::= { jnxPppIpv6ConfigEntry 1 }
jnxPppIpv6ConfigInitiateIpv6 OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enables the initiation of negotiation of the IPv6CP."
DEFVAL { disable }
::= { jnxPppIpv6ConfigEntry 2 }
jnxPppIpv6ConfigMaxIpv6cpRenegotiation OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of allowed ipv6cp renegotiation attempts from peer."
DEFVAL { 30 }
::= { jnxPppIpv6ConfigEntry 3 }
-- /////////////////////////////////////////////////////////////////////////////
--
-- PPP Globals
--
-- The globals are non interface based objects
--
-- /////////////////////////////////////////////////////////////////////////////
jnxPppPeerIpAddressOptional OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This option is used to ignore the conflicts between ppp client's
requested IP address and radius/local pool returned address in server
during IPNCP negotiation. Enabling this will ensure the IPNCP
negotiation to succeed even though the client does not include
IP address option in the IPNCP configure request."
::= { jnxPppGlobalConfig 1 }
END