mibs/MIBS/junos/JUNIPER-PING-MIB

1501 lines
58 KiB
Plaintext
Raw Permalink Normal View History

2023-12-05 12:25:34 +01:00
--
-- Juniper Enterprise Specific MIB: Ping MIB
--
-- Copyright (c) 2001-2012, Juniper Networks, Inc.
-- All rights reserved.
--
-- The contents of this document are subject to change without notice.
--
JUNIPER-PING-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, Unsigned32,
NOTIFICATION-TYPE
FROM SNMPv2-SMI -- RFC2578
InterfaceIndexOrZero
FROM IF-MIB -- RFC2863
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC2571
DisplayString, DateAndTime, TruthValue
FROM SNMPv2-TC
pingResultsEntry, pingProbeHistoryEntry, pingCtlTargetAddressType,
pingCtlTargetAddress, pingResultsOperStatus, pingResultsIpTargetAddressType,
pingResultsIpTargetAddress, pingResultsMinRtt, pingResultsMaxRtt,
pingResultsAverageRtt, pingResultsProbeResponses, pingResultsSentProbes,
pingResultsRttSumOfSquares, pingResultsLastGoodProbe,
OperationResponseStatus
FROM DISMAN-PING-MIB
InetPortNumber
FROM INET-ADDRESS-MIB
jnxMibs, jnxPingNotifications
FROM JUNIPER-SMI;
jnxPingMIB MODULE-IDENTITY
LAST-UPDATED "200911180000Z" -- November 18 00:00:00 2009 UTC
ORGANIZATION "Juniper Networks, Inc."
CONTACT-INFO
" Juniper Technical Assistance Center
Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, CA 94089
E-mail: support@juniper.net"
DESCRIPTION
"This is Juniper Networks' implementation of enterprise specific
portions of pingMib. Any data stored in this MIB has directly
related entries in mib-2, pingMIB."
-- revision history
REVISION "201109200000Z" -- September 20 00:00:00 2011 UTC
DESCRIPTION
"Updated the jnxPingCtlTargetPort description."
REVISION "200911180000Z" -- November 18 00:00:00 2009 UTC
DESCRIPTION
"Added jnxPingCtlEXseriesHWTimeStamp to jnxPingCtlTable."
REVISION "200904200000Z" -- April 20 00:00:00 2009 UTC
DESCRIPTION
"Added jnxPingCtlTargetPort to jnxPingCtlTable."
REVISION "200505010000Z" -- May 1 00:00:00 2005 UTC
DESCRIPTION
"Added jnxPingCtlTargetPort to jnxPingCtlTable."
REVISION "200404150000Z" -- April 15 00:00:00 2004 UTC
DESCRIPTION
"Added traps plus additional results & history data."
::= { jnxMibs 7 }
jnxPingObjects OBJECT IDENTIFIER ::= { jnxPingMIB 1 }
-- The registration node for ping implementation types
jnxPingImplementationTypeDomains OBJECT IDENTIFIER ::= { jnxPingMIB 2 }
jnxPingIcmpTimeStamp OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using the Internet
Control Message Protocol (ICMP) 'TimeStamp' facility.
This probe-type provides egress and ingress delay measurements."
::= { jnxPingImplementationTypeDomains 1 }
jnxPingHttpGet OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using an HTTP GET query to
calculate a round trip time."
::= { jnxPingImplementationTypeDomains 2 }
jnxPingHttpGetMetadata OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using an HTTP GET Metadata query to
calculate a round trip time."
::= { jnxPingImplementationTypeDomains 3 }
jnxPingDnsQuery OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using a DNS query to
calculate a round trip time."
::= { jnxPingImplementationTypeDomains 4 }
jnxPingNtpQuery OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using an NTP query to
calculate a round trip time."
::= { jnxPingImplementationTypeDomains 5 }
jnxPingUdpTimestamp OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using a UDP timestamp query to
calculate a round trip time. This probe-type provides egress and
ingress delay measurements"
::= { jnxPingImplementationTypeDomains 6 }
--
-- pingCtlTable extensions
--
jnxPingCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPingCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines the jnxPing Control Table for providing enterprise specific
options to the corresponding pingCtlTable entry."
::= { jnxPingObjects 2 }
jnxPingCtlEntry OBJECT-TYPE
SYNTAX JnxPingCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the jnxPingCtlTable. This essentially
augments the pingCtlTable with additional objects."
INDEX {
jnxPingCtlOwnerIndex,
jnxPingCtlTestName
}
::= { jnxPingCtlTable 1 }
JnxPingCtlEntry ::=
SEQUENCE {
jnxPingCtlOwnerIndex SnmpAdminString,
jnxPingCtlTestName SnmpAdminString,
jnxPingCtlIfName DisplayString,
jnxPingCtlRoutingIfIndex InterfaceIndexOrZero,
jnxPingCtlRoutingIfName DisplayString,
jnxPingCtlRoutingInstanceName DisplayString,
jnxPingCtlRttThreshold Unsigned32,
jnxPingCtlRttStdDevThreshold Unsigned32,
jnxPingCtlRttJitterThreshold Unsigned32,
jnxPingCtlEgressTimeThreshold Unsigned32,
jnxPingCtlEgressStdDevThreshold Unsigned32,
jnxPingCtlEgressJitterThreshold Unsigned32,
jnxPingCtlIngressTimeThreshold Unsigned32,
jnxPingCtlIngressStddevThreshold Unsigned32,
jnxPingCtlIngressJitterThreshold Unsigned32,
jnxPingCtlTrapGeneration BITS,
jnxPingCtlTargetPort InetPortNumber,
jnxPingCtlJseriesHWTimeStamp TruthValue,
jnxPingCtlOneWayHWTimeStamp TruthValue,
jnxPingCtlMovAvgSize Unsigned32,
jnxPingCtlMXseriesHWTimeStamp TruthValue,
jnxPingCtlEXseriesHWTimeStamp TruthValue
}
jnxPingCtlOwnerIndex OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"To facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 2575, VACM) for tables in which
multiple users may need to independently create or
modify entries, the initial index is used as an 'owner
index'. Such an initial index has a syntax of
SnmpAdminString, and can thus be trivially mapped to a
securityName or groupName as defined in VACM, in
accordance with a security policy.
When used in conjunction with such a security policy all
entries in the table belonging to a particular user (or
group) will have the same value for this initial index.
For a given user's entries in a particular table, the
object identifiers for the information in these entries
will have the same subidentifiers (except for the 'column'
subidentifier) up to the end of the encoded owner index.
To configure VACM to permit access to this portion of the
table, one would create vacmViewTreeFamilyTable entries
with the value of vacmViewTreeFamilySubtree including
the owner index portion, and vacmViewTreeFamilyMask
'wildcarding' the column subidentifier. More elaborate
configurations are possible."
::= { jnxPingCtlEntry 1 }
jnxPingCtlTestName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The name of the ping test. This is locally unique, within
the scope of an pingCtlOwnerIndex."
::= { jnxPingCtlEntry 2 }
jnxPingCtlIfName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..24))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this object to an interface name prior to starting a remote
ping operation directs the ping probes to be transmitted over the
specified interface. To specify the interface index instead, see
pingCtlIfIndex. The interface name must be specified under interfaces
statement of the JUNOS configuration. A zero length string value for
this object means that this option is not enabled. The following
values may be set simultaneously, however, only one value is used.
The precedence order is a follows:
pingCtlIfIndex (see pingCtlTable in pingMIB)
jnxPingCtlIfName
jnxPingCtlRoutingIfIndex (deprecated)
jnxPingCtlRoutingIfName (deprecated)
jnxPingCtlRoutingInstanceName"
DEFVAL { ''H }
::= { jnxPingCtlEntry 3 }
jnxPingCtlRoutingIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Use this option to specify the routing instance used when directing
outgoing ping packets. The interface ifIndex specified should be in
the desired routing instance table. The interface specified will not
necessarily be the interface packets are transmitted on. By default,
the source address of the packets will be set to the address of the
interface chosen. pingCtlSourceAddress should be used to override
the choice for source address if necessary. A value of zero for this
object means that this option is not enabled.
NOTE: deprecated by jnxPingCtlRoutingInstanceName"
DEFVAL { 0 }
::= { jnxPingCtlEntry 4 }
jnxPingCtlRoutingIfName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..24))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Use this option to specify the routing instance used when directing
outgoing ping packets. The interface name specified should be in
the desired routing instance table. The interface specified will not
necessarily be the interface packets are transmitted on. By default,
the source address of the packets will be set to the address of the
interface chosen. pingCtlSourceAddress should be used to override
the choice for source address if necessary.
NOTE: deprecated by jnxPingCtlRoutingInstanceName"
DEFVAL { ''H }
::= { jnxPingCtlEntry 5 }
jnxPingCtlRoutingInstanceName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..31))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use this option to specify the name of the routing instance used when
directing outgoing ping packets. The instance name specified must be
configured under routing-instances of the JUNOS configuration."
DEFVAL { ''H }
::= { jnxPingCtlEntry 6 }
jnxPingCtlRttThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..6000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum round trip time allowed. If this threshold is crossed
by any probe, a jnxPingRttThresholdExceeded trap will be sent."
DEFVAL { 0 }
::= { jnxPingCtlEntry 7 }
jnxPingCtlRttStdDevThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..6000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum round trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
round trip time at the end of any test exceeds this threshold,
a jnxPingRttStdDevThresholdExceeded trap will be sent."
DEFVAL { 0 }
::= { jnxPingCtlEntry 8 }
jnxPingCtlRttJitterThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..6000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum allowed jitter in the round trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum round trip times measured over the course of
a single test (jnxPingResultsMaxRttUs minus jnxPingResultsMinRttUs).
If the measured jitter exceeds this threshold, a
jnxPingRttJitterThresholdExceeded trap will be sent."
DEFVAL { 0 }
::= { jnxPingCtlEntry 9 }
jnxPingCtlEgressTimeThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum egress trip time allowed. If this threshold is crossed by
any probe, a jnxPingEgressThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 10 }
jnxPingCtlEgressStdDevThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum egress trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
egress trip time at the end of any test exceeds this threshold,
a jnxPingEgressStdDevThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 11 }
jnxPingCtlEgressJitterThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum allowed jitter in the egress trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum egress trip times measured over the course of
a single test (jnxPingResultsMaxSrcDstt minus jnxPingResultsMinSrcDstt).
If the measured jitter exceeds this threshold, a
jnxPingEgressJitterThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 12 }
jnxPingCtlIngressTimeThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum ingress trip time allowed. If this threshold is crossed by
any probe, a jnxPingIngressThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 13 }
jnxPingCtlIngressStddevThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum ingress trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
ingress trip time at the end of any test exceeds this threshold,
a jnxPingIngressStddevThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 14 }
jnxPingCtlIngressJitterThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..60000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum allowed jitter in the ingress trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum ingress trip times measured over the course of
a single test (jnxPingResultsMaxDstSrct minus jnxPingResultsMinDstSrct).
If the measured jitter exceeds this threshold, a
jnxPingIngressJitterThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType) provides one way
delay measurements. Currently jnxPingIcmpTimeStamp is the only
supported probe type with this property."
DEFVAL { 0 }
::= { jnxPingCtlEntry 15 }
jnxPingCtlTrapGeneration OBJECT-TYPE
SYNTAX BITS {
rttThreshold(0),
rttStdDevThreshold(1),
rttJitterThreshold(2),
egressThreshold(3),
egressStdDevThreshold(4),
egressJitterThreshold(5),
ingressThreshold(6),
ingressStdDevThreshold(7),
ingressJitterThreshold(8),
maxrttThreshold(9)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object determines when and if
to generate a notification for this entry:
rttThreshold(0) - Generate a jnxPingRttThresholdExceeded
notification when the configured rtt threshold
is exceeded.
rttStdDevThreshold(1) - Generate a jnxPingRttStdDevThresholdExceeded
notification when the configured rtt standard deviation
threshold is exceeded.
rttJitterThreshold(2) - Generate a jnxPingRttJitterThresholdExceeded
notification when the configured rtt jitter threshold
is exceeded.
egressThreshold(3) - Generate a jnxPingEgressThresholdExceeded
notification when the configured egress threshold is exceeded.
This applies only if the probe type supports one way measurments.
egressStdDevThreshold(4) - Generate a
jnxPingEgressStdDevThresholdExceeded notification when the
configured egress standard deviation threshold is exceeded.
This applies only if the probe type supports one way measurments.
egressJitterThreshold(5) - Generate a
jnxPingEgressJitterThresholdExceeded notification when the
configured egress jitter threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressThreshold(6) - Generate a jnxPingIngressThresholdExceeded
notification when the configured ingress threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressStdDevThreshold(7) - Generate a
jnxPingIngressStdDevThresholdExceeded notification when the
configured ingress standard deviation threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressJitterThreshold(8) - Generate a
jnxPingIngressJitterThresholdExceeded notification when the
configured ingress jitter threshold is exceeded.
This applies only if the probe type supports one way measurments.
The value of this object defaults to zero, indicating
that none of the above options have been selected.
maxrttThreshold(9) - Generate a jnxPingMaxRttThresholdExceeded
notification when the configured max rtt threshold
is exceeded."
::= { jnxPingCtlEntry 16 }
jnxPingCtlTargetPort OBJECT-TYPE
SYNTAX InetPortNumber (7 | 49152..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The target UDP/TCP port used by the probe.
When ICMP ping is used, jnxPingCtlTargetPort value will be shown as 0."
::= { jnxPingCtlEntry 17 }
jnxPingCtlJseriesHWTimeStamp OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use to enable the RPM Hardware Timestamp feature on J-series routers.
For M/T series routers, use the jnxPingCtlIfName and
pingCtlByPassRouteTable objects to redirect probes to the AS Pic.
For those routers, this object must have the value: false."
DEFVAL { false }
::= { jnxPingCtlEntry 18 }
jnxPingCtlOneWayHWTimeStamp OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use this object to enable Hardware Timestamp-based one-way
measurements. If this object is not enabled (ie, set to true),
no Hardware Timestamp based one way measurements or calculations
will be performed for this control entry. This object applies to
all Juniper routers. Note, due to clock synchronization artifacts,
many one-way jitter measurements & calculations may include signifacant
variations, in some cases orders of magnitude greater than the round
trip times."
DEFVAL { false }
::= { jnxPingCtlEntry 19 }
jnxPingCtlMovAvgSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Juniper RPM feature maintains a set of the most recent probe
measurements & provides the same calculations over that collection
as provided over a test (ie, average, standard deviation, etc). This
data is available via the jnx-rpm mib or via the CLI/XML. The
number of samples maintained in this moving collection is specified
by this object. This value must be less than the number of samples
maintained in the history table (ie, pingCtlMaxRows)."
DEFVAL { 0 }
::= { jnxPingCtlEntry 20 }
jnxPingCtlMXseriesHWTimeStamp OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use to enable the RPM Hardware Timestamp feature on MX-series routers.
For M/T series routers, use the jnxPingCtlIfName and
pingCtlByPassRouteTable objects to redirect probes to the AS PIC.
For those routers, this object must have the value: false."
DEFVAL { false }
::= { jnxPingCtlEntry 21 }
jnxPingCtlEXseriesHWTimeStamp OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use to enable the RPM Hardware Timestamp feature on EX-series switches.
For thoses, this object must have the value: false."
DEFVAL { false }
::= { jnxPingCtlEntry 22 }
jnxPingMaxRttThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..6000000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum round trip time allowed. If this threshold is crossed
by any probe of a test, a jnxPingMaxRttThresholdExceeded trap will be sent."
DEFVAL { 0 }
::= { jnxPingCtlEntry 23 }
--
-- Ping Results Table extensions
--
jnxPingResultsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPingResultsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Augments the pingResultsTable with additional data."
::= { jnxPingObjects 3 }
jnxPingResultsEntry OBJECT-TYPE
SYNTAX JnxPingResultsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry provides additional ping test results."
AUGMENTS { pingResultsEntry }
::= { jnxPingResultsTable 1 }
JnxPingResultsEntry ::=
SEQUENCE {
jnxPingResultsRttUs Unsigned32,
jnxPingResultsSumRttUs Unsigned32,
jnxPingResultsMinRttUs Unsigned32,
jnxPingResultsMaxRttUs Unsigned32,
jnxPingResultsAvgRttUs Unsigned32,
jnxPingResultsStdDevRttUs Unsigned32,
jnxPingResultsEgressUs Unsigned32,
jnxPingResultsMinEgressUs Unsigned32,
jnxPingResultsMaxEgressUs Unsigned32,
jnxPingResultsAvgEgressUs Unsigned32,
jnxPingResultsStddevEgressUs Unsigned32,
jnxPingResultsIngressUs Unsigned32,
jnxPingResultsMinIngressUs Unsigned32,
jnxPingResultsMaxIngressUs Unsigned32,
jnxPingResultsAvgIngressUs Unsigned32,
jnxPingResultsStddevIngressUs Unsigned32,
jnxPingResultsJitterRttUs Unsigned32,
jnxPingResultsJitterEgressUs Unsigned32,
jnxPingResultsJitterIngressUs Unsigned32,
jnxPingResultsStatus OperationResponseStatus,
jnxPingResultsTime DateAndTime,
jnxPingResultsOwnerIndex SnmpAdminString,
jnxPingResultsTestName SnmpAdminString
}
jnxPingResultsRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The round trip delays measured for the most recent successful probe
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 1 }
jnxPingResultsSumRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sum of the round trip delays measured for all the probes
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 2 }
jnxPingResultsMinRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the round trip delays measured for all the probes
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 3 }
jnxPingResultsMaxRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the round trip delays measured for all the probes
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 4 }
jnxPingResultsAvgRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the round trip delays measured for all the probes
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 5 }
jnxPingResultsStdDevRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the round trip delays measured
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 6 }
jnxPingResultsEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The egress trip delays measured for the most recent successful probe
during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 7 }
jnxPingResultsMinEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the egress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 8 }
jnxPingResultsMaxEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the egress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 9 }
jnxPingResultsAvgEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the egress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 10 }
jnxPingResultsStddevEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the egress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 11 }
jnxPingResultsIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ingress trip delays measured for the most recent successful probe
during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 12 }
jnxPingResultsMinIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the ingress trip delays measured for over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 13 }
jnxPingResultsMaxIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the ingress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 14 }
jnxPingResultsAvgIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the ingress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 15 }
jnxPingResultsStddevIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the ingress trip delays measured over all
probes during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 16 }
jnxPingResultsJitterRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The jitter of the round trip delays measured for all the probes
during this test. Measured in microseconds."
::= { jnxPingResultsEntry 17 }
jnxPingResultsJitterEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The jitter of the egress trip delays measured for all the probes
during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 18 }
jnxPingResultsJitterIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The jitter of the ingress trip delays measured for all the probes
during this test. Measured in microseconds.
This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingResultsEntry 19 }
jnxPingResultsStatus OBJECT-TYPE
SYNTAX OperationResponseStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The result of the most recent probe."
::= { jnxPingResultsEntry 20 }
jnxPingResultsTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp for when the most recent probe result was determined."
::= { jnxPingResultsEntry 21 }
jnxPingResultsOwnerIndex OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object has the same value as pingCtlOwnerIndex and is provided
for those applications that are unable to parse the value of
pingCtlOwnerIndex from the instance portion of the OIDs belonging to
this table."
::= { jnxPingResultsEntry 22 }
jnxPingResultsTestName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object has the same value as pingCtlTestName and is provided
for those applications that are unable to parse the value of
pingCtlTestName from the instance portion of the OIDs belonging to
this table."
::= { jnxPingResultsEntry 23 }
--
-- Ping History Table extensions
--
jnxPingProbeHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPingProbeHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Augments the pingHistoryTable with additional data."
::= { jnxPingObjects 4 }
jnxPingProbeHistoryEntry OBJECT-TYPE
SYNTAX JnxPingProbeHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry provides additional ping history data."
AUGMENTS { pingProbeHistoryEntry }
::= { jnxPingProbeHistoryTable 1 }
JnxPingProbeHistoryEntry ::=
SEQUENCE {
jnxPingProbeHistoryResponseUs Unsigned32,
jnxPingProbeHistoryJitterUs Unsigned32,
jnxPingProbeHistoryResponseEgressUs Unsigned32,
jnxPingProbeHistoryResponseIngressUs Unsigned32,
jnxPingProbeHistoryEgressJitterUs Unsigned32,
jnxPingProbeHistoryIngressJitterUs Unsigned32
}
jnxPingProbeHistoryResponseUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time measured in microseconds from when
a probe was sent to when its response was received or
when it timed out. The value of this object is reported
as 0 when it is not possible to transmit a probe."
::= { jnxPingProbeHistoryEntry 1 }
jnxPingProbeHistoryJitterUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time difference measured in microseconds between the maximum
and minimum round trip times. Each history entry provides a running
calculation of the jitter (calculated over the current test) at the
time a probe was completed."
::= { jnxPingProbeHistoryEntry 2 }
jnxPingProbeHistoryResponseEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time measured in microseconds from when
a probe was sent to when it was received by destination.
This applies only if the probe type (pingCtlType) provides one way
delay measurements.
For all other probe types, the value is irrelevant and will return 0."
::= { jnxPingProbeHistoryEntry 3 }
jnxPingProbeHistoryResponseIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time measured in microseconds from when
a probe was sent from the destination to when it was received.
This applies only if the probe type (pingCtlType) provides one way
delay measurements.
For all other probe types, the value is irrelevant and will return 0."
::= { jnxPingProbeHistoryEntry 4 }
jnxPingProbeHistoryEgressJitterUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time difference measured in microseconds between the maximum
and minimum egress trip times. Each history entry provides a running
calculation of the jitter (calculated over the current test) at the
time a probe was completed.
This applies only if the probe type (pingCtlType) provides one way
delay measurements.
For all other probe types, the value is irrelevant and will return 0."
::= { jnxPingProbeHistoryEntry 5 }
jnxPingProbeHistoryIngressJitterUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time difference measured in microseconds between the maximum
and minimum ingress trip times. Each history entry provides a running
calculation of the jitter (calculated over the current test) at the
time a probe was completed.
This applies only if the probe type (pingCtlType) provides one way
delay measurements.
For all other probe types, the value is irrelevant and will return 0."
::= { jnxPingProbeHistoryEntry 6 }
--
-- Last ping test Results Table
--
jnxPingLastTestResultTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPingLastTestResultEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Stores result of the most recently completed test. Entry corresponding
to a test will be created only after completion of first test."
::= { jnxPingObjects 5 }
jnxPingLastTestResultEntry OBJECT-TYPE
SYNTAX JnxPingLastTestResultEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry provides most recently completed test result."
INDEX {
jnxPingCtlOwnerIndex,
jnxPingCtlTestName
}
::= { jnxPingLastTestResultTable 1 }
JnxPingLastTestResultEntry ::=
SEQUENCE {
jnxPingLastTestResultProbeResponses Unsigned32,
jnxPingLastTestResultSentProbes Unsigned32,
jnxPingLastTestResultSumRttUs Unsigned32,
jnxPingLastTestResultMinRttUs Unsigned32,
jnxPingLastTestResultMaxRttUs Unsigned32,
jnxPingLastTestResultAvgRttUs Unsigned32,
jnxPingLastTestResultStdDevRttUs Unsigned32,
jnxPingLastTestResultMinEgressUs Unsigned32,
jnxPingLastTestResultMaxEgressUs Unsigned32,
jnxPingLastTestResultAvgEgressUs Unsigned32,
jnxPingLastTestResultStddevEgressUs Unsigned32,
jnxPingLastTestResultMinIngressUs Unsigned32,
jnxPingLastTestResultMaxIngressUs Unsigned32,
jnxPingLastTestResultAvgIngressUs Unsigned32,
jnxPingLastTestResultStddevIngressUs Unsigned32,
jnxPingLastTestResultPeakToPeakJitterRttUs Unsigned32,
jnxPingLastTestResultPeakToPeakJitterEgressUs Unsigned32,
jnxPingLastTestResultPeakToPeakJitterIngressUs Unsigned32,
jnxPingLastTestResultTime DateAndTime
}
jnxPingLastTestResultProbeResponses OBJECT-TYPE
SYNTAX Unsigned32
UNITS "responses"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of responses received in the most recently completed test."
::= { jnxPingLastTestResultEntry 1 }
jnxPingLastTestResultSentProbes OBJECT-TYPE
SYNTAX Unsigned32
UNITS "probes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reflects the number of probes sent in the
most recently completed test."
::= { jnxPingLastTestResultEntry 2 }
jnxPingLastTestResultSumRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sum of the round trip delays measured for all the probes
during the most recently completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 3 }
jnxPingLastTestResultMinRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the round trip delays measured for all the probes
during the most recently completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 4 }
jnxPingLastTestResultMaxRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the round trip delays measured for all the probes
during the most recently completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 5 }
jnxPingLastTestResultAvgRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the round trip delays measured for all the probes
during the most recently completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 6 }
jnxPingLastTestResultStdDevRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the round trip delays measured during
the most recently completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 7 }
jnxPingLastTestResultMinEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the egress trip delays measured over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 8 }
jnxPingLastTestResultMaxEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the egress trip delays measured over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 9 }
jnxPingLastTestResultAvgEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the egress trip delays measured over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 10 }
jnxPingLastTestResultStddevEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the egress trip delays measured over all
probes during the most recently completed test. Measured in
microseconds. This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 11 }
jnxPingLastTestResultMinIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum of the ingress trip delays measured for over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 12 }
jnxPingLastTestResultMaxIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum of the ingress trip delays measured over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 13 }
jnxPingLastTestResultAvgIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average of the ingress trip delays measured over all probes
during the most recently completed test. Measured in microseconds.
This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their
values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 14 }
jnxPingLastTestResultStddevIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The standard deviation of the ingress trip delays measured over all
probes during the most recently completed test. Measured in
microseconds. This applies only if the probe type (pingCtlType)
provides one-way delay measurements. For all other probe types,
their values are irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 15 }
jnxPingLastTestResultPeakToPeakJitterRttUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates the difference between the min and max delays over
the course of the last completed test. Measured in microseconds."
::= { jnxPingLastTestResultEntry 16 }
jnxPingLastTestResultPeakToPeakJitterEgressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates the difference between the min and max egress trip
delays over the course of the last completed test. Measured in
microseconds. This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their values are
irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 17 }
jnxPingLastTestResultPeakToPeakJitterIngressUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates the difference between the min and max ingress trip
delays over the course of the last completed test. Measured in
microseconds. This applies only if the probe type (pingCtlType) provides
one-way delay measurements. For all other probe types, their values are
irrelevant and will return 0."
::= { jnxPingLastTestResultEntry 18 }
jnxPingLastTestResultTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp for when the last test was completed."
::= { jnxPingLastTestResultEntry 19 }
--
-- Notification definitions
--
jnxPingNotificationPrefix OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All Juniper-specific ping notifications are registered under
this branch."
::= { jnxPingNotifications 0 }
jnxPingRttThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinRttUs,
jnxPingResultsMaxRttUs,
jnxPingResultsAvgRttUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsRttSumOfSquares,
pingResultsLastGoodProbe,
jnxPingCtlRttThreshold,
jnxPingResultsRttUs
}
STATUS current
DESCRIPTION
"This notification is generated when the round trip time
(jnxPingCtlRttThreshold) exceeds the configured
threshold (jnxPingCtlRttThreshold) and the rttThreshold bit is
set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 1 }
jnxPingRttStdDevThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinRttUs,
jnxPingResultsMaxRttUs,
jnxPingResultsAvgRttUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsRttSumOfSquares,
pingResultsLastGoodProbe,
jnxPingCtlRttStdDevThreshold,
jnxPingResultsStdDevRttUs
}
STATUS current
DESCRIPTION
"This notification is generated when the standard deviation of
the round trip time (jnxPingResultsStdDevRttUs) exceeds the
configured threshold (jnxPingCtlRttStdDevThreshold) and the
rttStdDevThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 2 }
jnxPingRttJitterThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinRttUs,
jnxPingResultsMaxRttUs,
jnxPingResultsAvgRttUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsRttSumOfSquares,
pingResultsLastGoodProbe,
jnxPingCtlRttJitterThreshold
}
STATUS current
DESCRIPTION
"This notification is generated when the round trip time jitter
(jnxPingResultsMaxRttUs minus jnxPingResultsMinRttUs) exceeds the
configured threshold (jnxPingCtlRttJitterThreshold) and the
rttJitterThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 3 }
jnxPingEgressThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinEgressUs,
jnxPingResultsMaxEgressUs,
jnxPingResultsAvgEgressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingCtlEgressTimeThreshold,
jnxPingResultsEgressUs
}
STATUS current
DESCRIPTION
"This notification is generated when the egress time
(jnxPingResultsEgressUs) exceeds the configured
threshold (jnxPingCtlEgressTimeThreshold) and the
egressThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 4 }
jnxPingEgressStdDevThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinEgressUs,
jnxPingResultsMaxEgressUs,
jnxPingResultsAvgEgressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingResultsStddevEgressUs,
jnxPingCtlEgressStdDevThreshold,
jnxPingResultsStddevEgressUs
}
STATUS current
DESCRIPTION
"This notification is generated when the standard deviation of
the egress time (jnxPingResultsStddevEgressUs) exceeds the
configured threshold (jnxPingCtlEgressStdDevThreshold) and the
egressStdDevThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 5 }
jnxPingEgressJitterThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinEgressUs,
jnxPingResultsMaxEgressUs,
jnxPingResultsAvgEgressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingCtlEgressJitterThreshold
}
STATUS current
DESCRIPTION
"This notification is generated when the egress time jitter
(jnxPingResultsMaxEgressUs minus jnxPingResultsMinEgressUs)
exceeds the configured threshold (jnxPingCtlEgressJitterThreshold)
and the egressJitterThreshold bit is set in
jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 6 }
jnxPingIngressThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinIngressUs,
jnxPingResultsMaxIngressUs,
jnxPingResultsAvgIngressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingCtlIngressTimeThreshold,
jnxPingResultsIngressUs
}
STATUS current
DESCRIPTION
"This notification is generated when the ingress time
(jnxPingResultsIngressUs) exceeds the configured
threshold (jnxPingCtlIngressTimeThreshold) and the
ingressThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 7 }
jnxPingIngressStddevThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinIngressUs,
jnxPingResultsMaxIngressUs,
jnxPingResultsAvgIngressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingResultsStddevIngressUs,
jnxPingCtlIngressStddevThreshold,
jnxPingResultsStddevIngressUs
}
STATUS current
DESCRIPTION
"This notification is generated when the standard deviation of
the ingress time (jnxPingResultsStddevIngressUs) exceeds the
configured threshold (jnxPingCtlIngressStddevThreshold) and the
ingressStdDevThreshold bit is set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 8 }
jnxPingIngressJitterThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinIngressUs,
jnxPingResultsMaxIngressUs,
jnxPingResultsAvgIngressUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsLastGoodProbe,
jnxPingCtlIngressJitterThreshold
}
STATUS current
DESCRIPTION
"This notification is generated when the ingress time jitter
(jnxPingResultsMaxIngressUs minus jnxPingResultsMinIngressUs)
exceeds the configured threshold (jnxPingCtlIngressJitterThreshold)
and the ingressJitterThreshold bit is set in
jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 9 }
jnxPingMaxRttThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
pingCtlTargetAddressType,
pingCtlTargetAddress,
pingResultsOperStatus,
pingResultsIpTargetAddressType,
pingResultsIpTargetAddress,
jnxPingResultsMinRttUs,
jnxPingResultsMaxRttUs,
jnxPingResultsAvgRttUs,
pingResultsProbeResponses,
pingResultsSentProbes,
pingResultsRttSumOfSquares,
pingResultsLastGoodProbe,
jnxPingCtlRttThreshold,
jnxPingResultsRttUs
}
STATUS current
DESCRIPTION
"This notification is generated when the max round trip time
(jnxPingCtlMaxRttThreshold) exceeds the configured
threshold (jnxPingCtlMaxRttThreshold) and the maxrttThreshold bit is
set in jnxPingCtlTrapGeneration."
::= { jnxPingNotificationPrefix 10 }
END