david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
98a672123c
mibs/MIBS/ATM-FORUM-ILMI40-MIB

2236 lines
84 KiB
Plaintext
Raw Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
ATM-FORUM-ILMI40-MIB DEFINITIONS ::= BEGIN
-- RCSID information
-- $RCSfile: atmf-ILMI40.mib,v $
-- $Revision: 1.2 $ $State: Exp $
-- $Date: 1997/06/24 22:13:48 $
-- $Author: eric $
-- This module provides authoritative definitions for Alcatel Internetworking,
-- Inc. implimentation of the ATM Forum ILMI 4.0 mib. It use and distribution
-- is regulated by both Alcatel Internetworking, Inc. and the ATM Forum.
-- The Address registration (net/user sides) is implimented
-- in a hard state machine, thus these groups have been
-- commented out.
-- This module will be extended, as needed.
-- Alcatel Internetworking, Inc. reserves the right to make changes in
-- specification and oher information contained in this document without
-- prior notice. The reader should consult Alcatel Internetworking, Inc.
-- to determine whether any such changes have been made.
-- Current MIBs are availible from the following URLs:
-- ftp://ftp.ind.alcatel.com/pub/products/mibs
-- http://www.ind.alcatel.com
-- In no event shall Alcatel Internetworking, Inc. be liable for any incidental,
-- indirect, special, or consequential damages whatsoever (including
-- but not limited to lost profits) arising out of or related to this
-- document or the information contained in it, even if Alcatel Internetworking,
-- Inc. has been advised of, known, or should have known, the
-- possibility of such damages.
-- atmf-ILMI40
-- Revision: 1.00
-- Date: Feb 21, 1997
IMPORTS
enterprises
FROM RFC1155-SMI
Counter, IpAddress
FROM RFC1155-SMI
DisplayString
FROM RFC1213-MIB
TRAP-TYPE
FROM RFC-1215
OBJECT-TYPE
FROM RFC-1212
;
-- Textual Conventions
-- All representations of ATM addresses in this MIB Module use
-- the data type:
AtmAddress ::= OCTET STRING (SIZE (0 .. 32))
-- Note this data type is used only by the deprecated object
-- atmfPortAddress. Another definition (a refined one) is
-- specified in the Textual Conventions MIB.
-- Boolean values use this data type from RFC-1903, "Textual Conventions
-- for Version 2 of the Simple Network Management Protocol (SNMPv2)"
TruthValue ::= INTEGER { true(1), false(2) }
-- CLNP address values use this data type from RFC-1238, "CLNS MIB for
-- use with Connectionless Network Protocol (ISO 8473) and End System
-- to Intermediate System (ISO 9542)"
ClnpAddress ::= OCTET STRING (SIZE (1..21))
-- ATM Service Categories use this data type (See [TM4.0]):
AtmServiceCategory ::=
INTEGER {
other(1),
cbr(2),
rtVbr(3),
nrtVbr(4),
abr(5),
ubr(6)
}
-- ATM End-System Addresses use this data type:
--AtmAddress ::= OCTET STRING (SIZE (8 | 20))
-- Network-Prefixes for an ATM Address use this data type:
--NetPrefix ::= OCTET STRING (SIZE (8 | 13))
-- In both the AtmAddress and NetPrefix conventions, Native E.164 addresses
-- are represented as 8 octets using the format specified in section
-- 3.1.1.3 of the ATM Forum UNI Signalling 4.0 specification.
-- In contrast, an NSAP-encoded address is 20 octets, and an NSAP-encoded
-- network prefix is 13 octets long.
-- MIB Groups
-- a subtree for defining ATM Forum MIB object types
-- enterprises OBJECT IDENTIFIER ::= { 0 }
atmForum OBJECT IDENTIFIER ::= { enterprises 353 }
-- a subtree for defining administrative object types
atmForumAdmin OBJECT IDENTIFIER ::= { atmForum 1 }
atmfTransmissionTypes OBJECT IDENTIFIER ::= { atmForumAdmin 2 }
atmfMediaTypes OBJECT IDENTIFIER ::= { atmForumAdmin 3 }
atmfTrafficDescrTypes OBJECT IDENTIFIER ::= { atmForumAdmin 4 }
atmfSrvcRegTypes OBJECT IDENTIFIER ::= { atmForumAdmin 5 }
-- a subtree for defining ATM Interface MIB object types
atmForumUni OBJECT IDENTIFIER ::= { atmForum 2 }
atmfPhysicalGroup OBJECT IDENTIFIER ::= { atmForumUni 1 }
atmfAtmLayerGroup OBJECT IDENTIFIER ::= { atmForumUni 2 }
atmfAtmStatsGroup OBJECT IDENTIFIER ::= { atmForumUni 3 }
atmfVpcGroup OBJECT IDENTIFIER ::= { atmForumUni 4 }
atmfVccGroup OBJECT IDENTIFIER ::= { atmForumUni 5 }
atmfAddressGroup OBJECT IDENTIFIER ::= { atmForumUni 6 }
atmfNetPrefixGroup OBJECT IDENTIFIER ::= { atmForumUni 7 }
atmfSrvcRegistryGroup OBJECT IDENTIFIER ::= { atmForumUni 8 }
atmfVpcAbrGroup OBJECT IDENTIFIER ::= { atmForumUni 9 }
atmfVccAbrGroup OBJECT IDENTIFIER ::= { atmForumUni 10 }
atmfAddressRegistrationAdminGroup OBJECT IDENTIFIER ::= { atmForumUni 11 }
-- Object Identifier definitions
-- Transmission Types: These values are no longer used
atmfUnknownType OBJECT IDENTIFIER ::= { atmfTransmissionTypes 1}
atmfSonetSTS3c OBJECT IDENTIFIER ::= { atmfTransmissionTypes 2 }
atmfDs3 OBJECT IDENTIFIER ::= { atmfTransmissionTypes 3 }
atmf4B5B OBJECT IDENTIFIER ::= { atmfTransmissionTypes 4 }
atmf8B10B OBJECT IDENTIFIER ::= { atmfTransmissionTypes 5 }
atmfSonetSTS12c OBJECT IDENTIFIER ::= { atmfTransmissionTypes 6 }
atmfE3 OBJECT IDENTIFIER ::= { atmfTransmissionTypes 7 }
atmfT1 OBJECT IDENTIFIER ::= { atmfTransmissionTypes 8 }
atmfE1 OBJECT IDENTIFIER ::= { atmfTransmissionTypes 9 }
-- Media Types: These values are no longer used
atmfMediaUnknownType OBJECT IDENTIFIER ::= { atmfMediaTypes 1 }
atmfMediaCoaxCable OBJECT IDENTIFIER ::= { atmfMediaTypes 2 }
atmfMediaSingleMode OBJECT IDENTIFIER ::= { atmfMediaTypes 3 }
atmfMediaMultiMode OBJECT IDENTIFIER ::= { atmfMediaTypes 4 }
atmfMediaStp OBJECT IDENTIFIER ::= { atmfMediaTypes 5 }
atmfMediaUtp OBJECT IDENTIFIER ::= { atmfMediaTypes 6 }
-- Traffic Descriptor Types: These types are combined with a five element
-- parameter vector to describe a Traffic Descriptor.
-- Traffic Descriptors along with a Best Effort Indicator are used to
-- indicate a Conformance Definition as defined in [TM4.0].
-- These types are no longer used
atmfNoDescriptor OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 1 }
atmfPeakRate OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 2 }
-- The No CLP/No SCR Type
-- Indicates the CBR.1 Conformance Definition if Best Effort is No
-- Indicates the UBR.1 and UBR.2 Conformance Definitions if Best Effort is Yes
atmfNoClpNoScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 3 }
-- The use of the parameter vector for this type:
-- Parameter #1 - peak cell rate in cells/second for CLP=0+1 traffic
-- Parameter #2 - CDVT in tenths of microseconds
-- Parameters #3, #4 and #5 are unused
-- These types are no longer used
atmfClpNoTaggingNoScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 4 }
atmfClpTaggingNoScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 5 }
-- The SCR/No CLP Type
-- Indicates the VBR.1 Conformance Definition
atmfNoClpScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 6 }
-- The use of the parameter vector for this type:
-- Parameter #1 - peak cell rate in cells/second for CLP=0+1 traffic
-- Parameter #2 - sustainable cell rate in cells/second for CLP=0+1 traffic
-- Parameter #3 - maximum burst size in cells
-- Parameter #4 - CDVT in tenths of microseconds
-- Parameter #5 - unused
-- The CLP without Tagging/SCR Type
-- Indicates the VBR.2 Conformance Definition
atmfClpNoTaggingScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 7 }
-- The use of the parameter vector for this type:
-- Parameter #1 - peak cell rate in cells/second for CLP=0+1 traffic
-- Parameter #2 - sustainable cell rate in cells/second for CLP=0 traffic
-- Parameter #3 - maximum burst size in cells
-- Parameter #4 - CDVT in tenths of microseconds
-- Parameter #5 - unused
-- The CLP with Tagging/SCR Type
-- Indicates the VBR.3 Conformance Definition
atmfClpTaggingScr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 8 }
-- The use of the parameter vector for this type:
-- Parameter #1 - peak cell rate in cells/second for CLP=0+1 traffic
-- Parameter #2 - sustainable cell rate in cells/second for CLP=0
-- traffic, excess tagged as CLP=1
-- Parameter #3 - maximum burst size in cells
-- Parameter #4 - CDVT in tenths of microseconds
-- Parameter #5 - unused
-- The ABR Type
-- Indicates the ABR Conformance Definition
atmfClpNoTaggingMcr OBJECT IDENTIFIER ::= { atmfTrafficDescrTypes 9 }
-- The use of the parameter vector for this type:
-- Parameter #1 - peak cell rate in cells/second
-- parameter #2 - CDVT in tenths of microseconds
-- Parameter #3 - minimum cell rate in cells/second
-- Parameter #4 - unused
-- Parameter #5 - unused
-- The Physical Port Group
--
-- This group is mandatory for all ATM Interface devices.
--
-- The Physical Port Table
atmfPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of physical layer status and parameter
information for the ATM Interface's physical interface."
::= { atmfPhysicalGroup 1 }
atmfPortEntry OBJECT-TYPE
SYNTAX AtmfPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about
the physical layer of an ATM Interface."
INDEX { atmfPortIndex }
::= { atmfPortTable 1 }
AtmfPortEntry ::=
SEQUENCE {
atmfPortIndex
INTEGER,
atmfPortAddress
AtmAddress,
atmfPortTransmissionType
OBJECT IDENTIFIER,
atmfPortMediaType
OBJECT IDENTIFIER,
atmfPortOperStatus
INTEGER,
atmfPortSpecific
OBJECT IDENTIFIER,
atmfPortMyIfName
DisplayString,
atmfPortMyIfIdentifier
INTEGER
}
atmfPortIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfPortEntry 1 }
atmfPortAddress OBJECT-TYPE
SYNTAX AtmAddress
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 2.0
of the UNI specification. The Address Group, defined
in theAddress Registration MIB should be used instead."
::= { atmfPortEntry 2 }
atmfPortTransmissionType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification. Appropriate Network Management
MIBs should be used instead."
::= { atmfPortEntry 3 }
atmfPortMediaType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification. Appropriate Network Management
MIBs should be used instead."
::= { atmfPortEntry 4 }
atmfPortOperStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
inService(2),
outOfService(3),
loopBack(4)
}
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification. Appropriate Network Management
MIBs should be used instead."
::= { atmfPortEntry 5 }
atmfPortSpecific OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification. Appropriate Network Management
MIBs should be used instead."
::= { atmfPortEntry 6 }
atmfPortMyIfName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual name of this interface. If this system is
manageable through SNMP, and supports the object
ifName, the value of this object must be identical
with that of ifName for the ifEntry of the lowest
level physical interface for this port. This interface
must be uniquely named on this system to distinguish
parallel links with a neighboring system. If this
interface does not have a textual name, the value of
this object is a zero length string."
::= { atmfPortEntry 7 }
atmfPortMyIfIdentifier OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for each ATM interface. The scheme used to
number the ATM interfaces on an ATM device is
implementation specific. One way to generate this value is
to use the ifIndex that an SNMP manager would use to
identify the port. This interface must be uniquely numbered
on this system to distinguish parallel links with a
neighboring system."
::= { atmfPortEntry 8 }
-- Note: The typical IME will support only one of the following two objects
atmfMyIpNmAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An IP Address to which a Network Management Station
can send Network Management protocol messages, e.g. SNMP
messages to UDP port 161, in order to access network
management information concerning the operation of the
ATM device local to this IME. If this object is supported,
but the Network Management Agent has not been configured with
an IP Address, the IME should return 0.0.0.0."
::= { atmfPhysicalGroup 2 }
atmfMyOsiNmNsapAddress OBJECT-TYPE
SYNTAX ClnpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An NSAP Address to which a Network Management Station
can send Network Management protocol messages in order
to access network management information concerning
the operation of the ATM device local to this IME.
If this object is supported,
but the Network Management Agent has not been configured with
an NSAP Address, the IME should return 0.0.0.0"
::= { atmfPhysicalGroup 3 }
atmfMySystemIdentifier OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (6))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A 48 bit identifier, taken from the IEEE universally
administered MAC address space, which uniquely
identifies the ATM device local to this IME."
::= { atmfPhysicalGroup 4 }
-- The ATM Layer Group
-- This group is mandatory for all ATM Interfaces.
--
-- ATM-layer specific information for the ATM Interface.
atmfAtmLayerTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfAtmLayerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of ATM layer status and parameter information
for the ATM Interface."
::= { atmfAtmLayerGroup 1 }
atmfAtmLayerEntry OBJECT-TYPE
SYNTAX AtmfAtmLayerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about
the ATM layer of an ATM Interface."
INDEX { atmfAtmLayerIndex }
::= { atmfAtmLayerTable 1 }
AtmfAtmLayerEntry ::=
SEQUENCE {
atmfAtmLayerIndex
INTEGER,
atmfAtmLayerMaxVPCs
INTEGER,
atmfAtmLayerMaxVCCs
INTEGER,
atmfAtmLayerConfiguredVPCs
INTEGER,
atmfAtmLayerConfiguredVCCs
INTEGER,
atmfAtmLayerMaxVpiBits
INTEGER,
atmfAtmLayerMaxVciBits
INTEGER,
atmfAtmLayerUniType
INTEGER,
atmfAtmLayerUniVersion
INTEGER,
atmfAtmLayerDeviceType
INTEGER,
atmfAtmLayerIlmiVersion
INTEGER,
atmfAtmLayerNniSigVersion
INTEGER,
atmfAtmLayerMaxSvpcVpi
INTEGER,
atmfAtmLayerMaxSvccVpi
INTEGER,
atmfAtmLayerMinSvccVci
INTEGER
}
atmfAtmLayerIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfAtmLayerEntry 1 }
atmfAtmLayerMaxVPCs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of switched and permanent VPCs
supported on this ATM Interface. For virtual interfaces
(i.e. Virtual Path Connections), the maximum number of VPCs
PNNI may communicate over is set to zero."
::= { atmfAtmLayerEntry 2 }
atmfAtmLayerMaxVCCs OBJECT-TYPE
SYNTAX INTEGER (0..268435456)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of switched and permanent VCCs
supported on this ATM Interface."
::= { atmfAtmLayerEntry 3 }
atmfAtmLayerConfiguredVPCs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of permanent VPCs configured for use on
this ATM Interface. For virtual interfaces (i.e. Virtual Path
Connections used by PNNI), the maximum number of VPCs
is set to zero."
::= { atmfAtmLayerEntry 4 }
atmfAtmLayerConfiguredVCCs OBJECT-TYPE
SYNTAX INTEGER (0..268435456)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of permanent VCCs configured for use on
this ATM Interface."
::= { atmfAtmLayerEntry 5 }
atmfAtmLayerMaxVpiBits OBJECT-TYPE
SYNTAX INTEGER (0..12)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of active VPI bits on this ATM Interface.
For virtual interfaces (i.e. Virtual Path Connections used by PNNI),
this value has no meaning and is set to zero."
::= { atmfAtmLayerEntry 6 }
atmfAtmLayerMaxVciBits OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of active VCI bits on this ATM Interface."
::= { atmfAtmLayerEntry 7 }
atmfAtmLayerUniType OBJECT-TYPE
SYNTAX INTEGER { public(1), private(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of the ATM device, either public or private."
::= { atmfAtmLayerEntry 8 }
atmfAtmLayerUniVersion OBJECT-TYPE
SYNTAX INTEGER {
version2point0(1),
version3point0(2),
version3point1(3),
version4point0(4),
unsupported(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of the latest version of the ATM Forum UNI
Signalling Specification that is supported on this ATM
Interface. If this value is not present, a version of the UNI
earlier than 3.1 is supported.
If the peer IME's value of this object is the same as,
or later than the local IME's value, then the version
corresponding to the local IME's value should be
attempted. Otherwise, if the peer IME's value of this
object is earlier, and supported locally, then the
local IME should attempt the version corresponding to
the peer IME's value. Otherwise, compatibility of the
two IMEs cannot be assumed."
::= { atmfAtmLayerEntry 9 }
atmfAtmLayerDeviceType OBJECT-TYPE
SYNTAX INTEGER { user(1), node(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object determines the type of the ATM device. This
object is used in automatic ATM Interface-Type determination
procedure such that a correct operational ATM
Interface-type can be determined. An ATM End System
shall take the value of user(1), and an ATM network
node shall take the value of node(2)."
::= { atmfAtmLayerEntry 10 }
atmfAtmLayerIlmiVersion OBJECT-TYPE
SYNTAX INTEGER { unsupported(1), version4point0(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of the latest version of the ATM Forum
ILMI Specification that is supported on this ATM Interface.
If the peer IME's value of this object is the same as,
or later than the local IME's value, then the version
corresponding to the local IME's value should be
attempted. Otherwise, if the peer IME's value of this
object is earlier, and supported locally, then the
local IME should attempt the version corresponding to
the peer IME's value. Otherwise, compatibility of the
two IMEs cannot be assumed.
If this object is not present, a version of the ILMI earlier
than 4.0 is supported."
::= { atmfAtmLayerEntry 11 }
atmfAtmLayerNniSigVersion OBJECT-TYPE
SYNTAX INTEGER { unsupported(1), iisp(2),
pnniVersion1point0(3) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of the latest version of the ATM Forum
PNNI Signalling Specification that is supported on this
ATM Interface. Note that the PNNI routing version is not
determined through ILMI.
If the peer IME's value of this object is the same as,
or later than the local IME's value, then the version
corresponding to the local IME's value should be
attempted. Otherwise, if the peer IME's value of this
object is earlier, and supported locally, then the
local IME should attempt the version corresponding to
the peer IME's value. Otherwise, compatibility of the
two IMEs cannot be assumed."
::= { atmfAtmLayerEntry 12 }
atmfAtmLayerMaxSvpcVpi OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum VPI that the signalling stack on the ATM
interface is configured to support for allocation to
switched virtual path connections."
::= { atmfAtmLayerEntry 13 }
atmfAtmLayerMaxSvccVpi OBJECT-TYPE
SYNTAX INTEGER (0..4096)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum VPI that the signalling stack on the ATM
interface is configured to support for allocation to
switched virtual channel connections."
::= { atmfAtmLayerEntry 14 }
atmfAtmLayerMinSvccVci OBJECT-TYPE
SYNTAX INTEGER (0..65536)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the minimum VCI value that the
signalling stack is configured to support for
allocation to switched virtual channel connections. The same
value applies to all SVCC VPI values for which the
signalling stack is configured."
::= { atmfAtmLayerEntry 15 }
-- The ATM Statistics Group
-- This group is deprecated and should not be implemented except as
-- required for backward compatibility with version 3.1 of the UNI
-- specification.
atmfAtmStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfAtmStatsEntry
ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This group is deprecated and should not be implemented
except as required for backward compatibility with version
3.1 of the UNI specification."
::= { atmfAtmStatsGroup 1 }
atmfAtmStatsEntry OBJECT-TYPE
SYNTAX AtmfAtmStatsEntry
ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
INDEX { atmfAtmStatsIndex }
::= { atmfAtmStatsTable 1 }
AtmfAtmStatsEntry ::=
SEQUENCE {
atmfAtmStatsIndex
INTEGER,
atmfAtmStatsReceivedCells
Counter,
atmfAtmStatsDroppedReceivedCells
Counter,
atmfAtmStatsTransmittedCells
Counter
}
atmfAtmStatsIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfAtmStatsEntry 1 }
atmfAtmStatsReceivedCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfAtmStatsEntry 2 }
atmfAtmStatsDroppedReceivedCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfAtmStatsEntry 3 }
atmfAtmStatsTransmittedCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfAtmStatsEntry 4 }
-- The Virtual Path Group
-- This group is mandatory for all ATM Interfaces.
--
-- Information concerning Virtual Path Connections
atmfVpcTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfVpcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of status and parameter information on the
virtual path connections which cross this ATM
Interface. There is one entry in this table for each
permanent virtual path connection."
::= { atmfVpcGroup 1 }
atmfVpcEntry OBJECT-TYPE
SYNTAX AtmfVpcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular virtual path connection."
INDEX { atmfVpcPortIndex, atmfVpcVpi }
::= { atmfVpcTable 1 }
AtmfVpcEntry ::=
SEQUENCE {
atmfVpcPortIndex
INTEGER,
atmfVpcVpi
INTEGER,
atmfVpcOperStatus
INTEGER,
atmfVpcTransmitTrafficDescriptorType
OBJECT IDENTIFIER,
atmfVpcTransmitTrafficDescriptorParam1
INTEGER,
atmfVpcTransmitTrafficDescriptorParam2
INTEGER,
atmfVpcTransmitTrafficDescriptorParam3
INTEGER,
atmfVpcTransmitTrafficDescriptorParam4
INTEGER,
atmfVpcTransmitTrafficDescriptorParam5
INTEGER,
atmfVpcReceiveTrafficDescriptorType
OBJECT IDENTIFIER,
atmfVpcReceiveTrafficDescriptorParam1
INTEGER,
atmfVpcReceiveTrafficDescriptorParam2
INTEGER,
atmfVpcReceiveTrafficDescriptorParam3
INTEGER,
atmfVpcReceiveTrafficDescriptorParam4
INTEGER,
atmfVpcReceiveTrafficDescriptorParam5
INTEGER,
atmfVpcQoSCategory
INTEGER,
atmfVpcTransmitQoSClass
INTEGER,
atmfVpcReceiveQoSClass
INTEGER,
atmfVpcBestEffortIndicator
TruthValue,
atmfVpcServiceCategory
AtmServiceCategory
}
atmfVpcPortIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfVpcEntry 1 }
atmfVpcVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection at the
local ATM Interface."
::= { atmfVpcEntry 2 }
atmfVpcOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
end2endUp(2),
end2endDown(3),
localUpEnd2endUnknown(4),
localDown(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present actual operational status of the VPC.
A value of end2endUp(2) or end2endDown(3) would be
used if the end-to-end status is known. If only local
status information is available, a value of
localUpEnd2endUnknown(4) or localDown(5) would be
used."
::= { atmfVpcEntry 3 }
atmfVpcTransmitTrafficDescriptorType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of traffic management, applicable to the
transmit direction of this VPC. The type may indicate
none, or a type with one or more parameters. These
parameters are specified as a parameter vector, in the
corresponding instances of the objects:
atmfVpcTransmitTrafficDescriptorParam1,
atmfVpcTransmitTrafficDescriptorParam2,
atmfVpcTransmitTrafficDescriptorParam3,
atmfVpcTransmitTrafficDescriptorParam4, and
atmfVpcTransmitTrafficDescriptorParam5."
::= { atmfVpcEntry 4 }
atmfVpcTransmitTrafficDescriptorParam1 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first parameter of the transmit parameter vector
for this VPC, used according to the value of
atmfVpcTransmitTrafficDescriptorType."
::= { atmfVpcEntry 5 }
atmfVpcTransmitTrafficDescriptorParam2 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The second parameter of the transmit parameter vector
for this VPC, used according to the value of
atmfVpcTransmitTrafficDescriptorType."
::= { atmfVpcEntry 6 }
atmfVpcTransmitTrafficDescriptorParam3 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The third parameter of the transmit parameter vector
for this VPC, used according to the value of
atmfVpcTransmitTrafficDescriptorType."
::= { atmfVpcEntry 7 }
atmfVpcTransmitTrafficDescriptorParam4 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fourth parameter of the transmit parameter vector
for this VPC, used according to the value of
atmfVpcTransmitTrafficDescriptorType."
::= { atmfVpcEntry 8 }
atmfVpcTransmitTrafficDescriptorParam5 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fifth parameter of the transmit parameter vector
for this VPC, used according to the value of
atmfVpcTransmitTrafficDescriptorType."
::= { atmfVpcEntry 9 }
atmfVpcReceiveTrafficDescriptorType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of traffic management, applicable to the
traffic in the receive direction of this VPC. The type
may indicate none, or a type with one or more
parameters. These parameters are specified as a
parameter vector, in the corresponding instances of
the objects:
atmfVpcReceiveTrafficDescriptorParam1,
atmfVpcReceiveTrafficDescriptorParam2,
atmfVpcReceiveTrafficDescriptorParam3,
atmfVpcReceiveTrafficDescriptorParam4, and
atmfVpcReceiveTrafficDescriptorParam5."
::= { atmfVpcEntry 10 }
atmfVpcReceiveTrafficDescriptorParam1 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first parameter of the receive parameter vector
for this VPC, used according to the value of
atmfVpcReceiveTrafficDescriptorType."
::= { atmfVpcEntry 11 }
atmfVpcReceiveTrafficDescriptorParam2 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The second parameter of the receive parameter vector
for this VPC, used according to the value of
atmfVpcReceiveTrafficDescriptorType."
::= { atmfVpcEntry 12 }
atmfVpcReceiveTrafficDescriptorParam3 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The third parameter of the receive parameter vector
for this VPC, used according to the value of
atmfVpcReceiveTrafficDescriptorType."
::= { atmfVpcEntry 13 }
atmfVpcReceiveTrafficDescriptorParam4 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fourth parameter of the receive parameter vector
for this VPC, used according to the value of
atmfVpcReceiveTrafficDescriptorType."
::= { atmfVpcEntry 14 }
atmfVpcReceiveTrafficDescriptorParam5 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fifth parameter of the receive parameter vector
for this VPC, used according to the value of
atmfVpcReceiveTrafficDescriptorType."
::= { atmfVpcEntry 15 }
atmfVpcQoSCategory OBJECT-TYPE
SYNTAX INTEGER {
other(1),
deterministic (2),
statistical (3),
unspecified (4)
}
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 2.0
of the UNI specification."
::= { atmfVpcEntry 16 }
atmfVpcTransmitQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfVpcEntry 17 }
atmfVpcReceiveQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfVpcEntry 18 }
atmfVpcBestEffortIndicator OBJECT-TYPE
SYNTAX TruthValue
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The object is examined when
atmfVpcTransmitTrafficDescriptorType or
atmfVpcReceiveTrafficDescriptorType for the associated
connection is equal to atmfNoClpNoScr.
If this object is set to false(2), the network is requested
to apply the CBR.1 conformance definition. If this object
is set to true(1), the network is requested to apply the
UBR.1 conformance definition."
::= { atmfVpcEntry 19 }
atmfVpcServiceCategory OBJECT-TYPE
SYNTAX AtmServiceCategory
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The service category of this virtual path connection."
::= { atmfVpcEntry 20 }
-- The Virtual Path ABR Group
-- This group contains per-VPC information, support for which is optional.
--
-- Attributes of ABR Virtual Path connections
atmfVpcAbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfVpcAbrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of operational parameters related to the ABR
virtual path connections which cross this ATM
Interface. There is one entry in this table for each
ABR virtual path connection.
Each virtual path connection represented
in this table must also be represented by
an entry in the atmfVpcTable."
::= { atmfVpcAbrGroup 1 }
atmfVpcAbrEntry OBJECT-TYPE
SYNTAX AtmfVpcAbrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular ABR virtual path connection."
INDEX { atmfVpcAbrPortIndex, atmfVpcAbrVpi }
::= { atmfVpcAbrTable 1 }
AtmfVpcAbrEntry ::=
SEQUENCE {
atmfVpcAbrPortIndex
INTEGER,
atmfVpcAbrVpi
INTEGER,
atmfVpcAbrTransmitIcr
INTEGER,
atmfVpcAbrTransmitNrm
INTEGER,
atmfVpcAbrTransmitTrm
INTEGER,
atmfVpcAbrTransmitCdf
INTEGER,
atmfVpcAbrTransmitRif
INTEGER,
atmfVpcAbrTransmitRdf
INTEGER,
atmfVpcAbrTransmitAdtf
INTEGER,
atmfVpcAbrTransmitCrm
INTEGER
}
atmfVpcAbrPortIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of identifying
the ATM Interface over which this message was received."
::= { atmfVpcAbrEntry 1 }
atmfVpcAbrVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this ABR Virtual Path Connection at the
local ATM Interface."
::= { atmfVpcAbrEntry 2 }
atmfVpcAbrTransmitIcr OBJECT-TYPE
SYNTAX INTEGER (0..16777215)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Initial Cell Rate: This is the rate at which the
source starts, both initially and after an idle period.
The unit is cells per second. The value must not be
larger than PCR, and is usually lower."
::= { atmfVpcAbrEntry 3 }
atmfVpcAbrTransmitNrm OBJECT-TYPE
SYNTAX INTEGER {
nrm2(1),
nrm4(2),
nrm8(3),
nrm16(4),
nrm32(5),
nrm64(6),
nrm128(7),
nrm256(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of data cells a source may send
for each forward RM-cell. The default value is nrm32(5)."
::= { atmfVpcAbrEntry 4 }
atmfVpcAbrTransmitTrm OBJECT-TYPE
SYNTAX INTEGER {
trm0point78125(1),
trm1point5625(2),
trm3point125(3),
trm6point25(4),
trm12point5(5),
trm25(6),
trm50(7),
trm100(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Upper bound on the time between forward RM-cells for
an active source (in milliseconds). The default value
is trm100(8)."
::= { atmfVpcAbrEntry 5 }
atmfVpcAbrTransmitCdf OBJECT-TYPE
SYNTAX INTEGER {
cdf0(1),
cdfOneOver64(2),
cdfOneOver32(3),
cdfOneOver16(4),
cdfOneOver8(5),
cdfOneOver4(6),
cdfOneOver2(7),
cdfOne(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Cutoff Decrease Factor: This field controls the rate
decrease associated with lost or delayed backward RM
cells. Larger values result in faster rate decrease.
The default value is cdfOneOver16(4)."
::= { atmfVpcAbrEntry 6 }
atmfVpcAbrTransmitRif OBJECT-TYPE
SYNTAX INTEGER {
rifOneOver32768(1),
rifOneOver16384(2),
rifOneOver8192(3),
rifOneOver4096(4),
rifOneOver2048(5),
rifOneOver1024(6),
rifOneOver512(7),
rifOneOver256(8),
rifOneOver128(9),
rifOneOver64(10),
rifOneOver32(11),
rifOneOver16(12),
rifOneOver8(13),
rifOneOver4(14),
rifOneOver2(15),
rifOne(16)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Rate Increment Factor: Controls the rate at which the rate
increases, when a backward RM-cell is received with CI=0 and
NI=0. Larger values lead to faster rate increase. The default
value is rifOneOver16(12)."
::= { atmfVpcAbrEntry 7 }
atmfVpcAbrTransmitRdf OBJECT-TYPE
SYNTAX INTEGER {
rdfOneOver32768(1),
rdfOneOver16384(2),
rdfOneOver8192(3),
rdfOneOver4096(4),
rdfOneOver2048(5),
rdfOneOver1024(6),
rdfOneOver512(7),
rdfOneOver256(8),
rdfOneOver128(9),
rdfOneOver64(10),
rdfOneOver32(11),
rdfOneOver16(12),
rdfOneOver8(13),
rdfOneOver4(14),
rdfOneOver2(15),
rdfOne(16)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Rate Decrease Factor: Controls the rate decrease
which occurs when backward RM-cells with CI=1, are
received. Larger values lead to faster rate
decrease. The default value is rdfOneOver16(12)."
::= { atmfVpcAbrEntry 8 }
atmfVpcAbrTransmitAdtf OBJECT-TYPE
SYNTAX INTEGER (1..1023)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"ACR Decrease Time Factor: Time permitted between
sending RM-cells, before the allowed rate (ACR) is
decreased to ICR. Range is 10 ms to 10.23 seconds.
The unit is 10 milliseconds. For example, the default
value of 50 corresponds to a time factor of 500 ms.
Larger values allow a source to retain its current
rate longer, during periods of relative inactivity.
The default is 50 (0.5 seconds)."
::= { atmfVpcAbrEntry 9 }
atmfVpcAbrTransmitCrm OBJECT-TYPE
SYNTAX INTEGER (0..8388608)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"RM Cells Before Cutoff: Limits the number of forward
RM-cells which may be sent in the absence of received
backward RM-cells."
::= { atmfVpcAbrEntry 10 }
-- The Virtual Channel Group
-- This group is mandatory for all ATM Interfaces.
--
-- Information concerning Virtual Channel Connections
atmfVccTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of status and parameter information on the
virtual channel connections which are visible at this
ATM Interface. There is one entry in this table for
each permanent virtual channel connection, including
reserved VCCs that are supported; e.g., signalling,
OAM flows, and ILMI, but not unassigned cells."
::= { atmfVccGroup 1 }
atmfVccEntry OBJECT-TYPE
SYNTAX AtmfVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular virtual channel connection."
INDEX { atmfVccPortIndex, atmfVccVpi, atmfVccVci }
::= { atmfVccTable 1 }
AtmfVccEntry ::=
SEQUENCE {
atmfVccPortIndex
INTEGER,
atmfVccVpi
INTEGER,
atmfVccVci
INTEGER,
atmfVccOperStatus
INTEGER,
atmfVccTransmitTrafficDescriptorType
OBJECT IDENTIFIER,
atmfVccTransmitTrafficDescriptorParam1
INTEGER,
atmfVccTransmitTrafficDescriptorParam2
INTEGER,
atmfVccTransmitTrafficDescriptorParam3
INTEGER,
atmfVccTransmitTrafficDescriptorParam4
INTEGER,
atmfVccTransmitTrafficDescriptorParam5
INTEGER,
atmfVccReceiveTrafficDescriptorType
OBJECT IDENTIFIER,
atmfVccReceiveTrafficDescriptorParam1
INTEGER,
atmfVccReceiveTrafficDescriptorParam2
INTEGER,
atmfVccReceiveTrafficDescriptorParam3
INTEGER,
atmfVccReceiveTrafficDescriptorParam4
INTEGER,
atmfVccReceiveTrafficDescriptorParam5
INTEGER,
atmfVccQoSCategory
INTEGER,
atmfVccTransmitQoSClass
INTEGER,
atmfVccReceiveQoSClass
INTEGER,
atmfVccBestEffortIndicator
TruthValue,
atmfVccTransmitFrameDiscard
TruthValue,
atmfVccReceiveFrameDiscard
TruthValue,
atmfVccServiceCategory
AtmServiceCategory
}
atmfVccPortIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfVccEntry 1 }
atmfVccVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Channel Connection at
the local ATM Interface. For virtual interfaces (i.e.
Virtual Path Connections), this value has no meaning
and is set to zero "
::= { atmfVccEntry 2 }
atmfVccVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection at
the local ATM Interface."
::= { atmfVccEntry 3 }
atmfVccOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
end2endUp(2),
end2endDown(3),
localUpEnd2endUnknown(4),
localDown(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present actual operational status of the VCC. A
value of end2endUp(2) or end2endUp(3) is used if the
end to end status is known.
If only local status is known a value of
localUpEnd2endUnknown(4) or localDown(5) is used."
::= { atmfVccEntry 4 }
atmfVccTransmitTrafficDescriptorType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of traffic management, applicable to the
transmit direction of this VCC. The type may indicate
none, or a type with one or more parameters. These
parameters are specified as a parameter vector, in the
corresponding instances of the objects:
atmfVccTransmitTrafficDescriptorParam1,
atmfVccTransmitTrafficDescriptorParam2,
atmfVccTransmitTrafficDescriptorParam3,
atmfVccTransmitTrafficDescriptorParam4, and
atmfVccTransmitTrafficDescriptorParam5."
::= { atmfVccEntry 5 }
atmfVccTransmitTrafficDescriptorParam1 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first parameter of the transmit parameter vector
for this VCC, used according to the value of
atmfVccTransmitTrafficDescriptorType."
::= { atmfVccEntry 6 }
atmfVccTransmitTrafficDescriptorParam2 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The second parameter of the transmit parameter vector
for this VCC, used according to the value of
atmfVccTransmitTrafficDescriptorType."
::= { atmfVccEntry 7 }
atmfVccTransmitTrafficDescriptorParam3 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The third parameter of the transmit parameter vector
for this VCC, used according to the value of
atmfVccTransmitTrafficDescriptorType."
::= { atmfVccEntry 8 }
atmfVccTransmitTrafficDescriptorParam4 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fourth parameter of the transmit parameter vector
for this VCC, used according to the value of
atmfVccTransmitTrafficDescriptorType."
::= { atmfVccEntry 9 }
atmfVccTransmitTrafficDescriptorParam5 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fifth parameter of the transmit parameter vector
for this VCC, used according to the value of
atmfVccTransmitTrafficDescriptorType."
::= { atmfVccEntry 10 }
atmfVccReceiveTrafficDescriptorType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of traffic management, applicable to the
traffic in the receive direction of this VCC. The type
may indicate none, or a type with one or more
parameters. These parameters are specified as a
parameter vector, in the corresponding instances of
the objects:
atmfVccReceiveTrafficDescriptorParam1,
atmfVccReceiveTrafficDescriptorParam2,
atmfVccReceiveTrafficDescriptorParam3,
atmfVccReceiveTrafficDescriptorParam4, and
atmfVccReceiveTrafficDescriptorParam5."
::= { atmfVccEntry 11 }
atmfVccReceiveTrafficDescriptorParam1 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The first parameter of the receive parameter vector
for this VCC, used according to the value of
atmfVccReceiveTrafficDescriptorType."
::= { atmfVccEntry 12 }
atmfVccReceiveTrafficDescriptorParam2 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The second parameter of the receive parameter vector
for this VCC, used according to the value of
atmfVccReceiveTrafficDescriptorType."
::= { atmfVccEntry 13 }
atmfVccReceiveTrafficDescriptorParam3 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The third parameter of the receive parameter vector
for this VCC, used according to the value of
atmfVccReceiveTrafficDescriptorType."
::= { atmfVccEntry 14 }
atmfVccReceiveTrafficDescriptorParam4 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fourth parameter of the receive parameter vector
for this VCC, used according to the value of
atmfVccReceiveTrafficDescriptorType."
::= { atmfVccEntry 15 }
atmfVccReceiveTrafficDescriptorParam5 OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The fifth parameter of the receive parameter vector
for this VCC, used according to the value of
atmfVccReceiveTrafficDescriptorType."
::= { atmfVccEntry 16 }
atmfVccQoSCategory OBJECT-TYPE
SYNTAX INTEGER {
other(1),
deterministic(2),
statistical(3),
unspecified(4)
}
ACCESS read-only
STATUS obsolete
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 2.0
of the UNI specification."
::= { atmfVccEntry 17 }
atmfVccTransmitQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfVccEntry 18 }
atmfVccReceiveQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object should not be implemented except as
required for backward compatibility with version 3.1
of the UNI specification."
::= { atmfVccEntry 19 }
atmfVccBestEffortIndicator OBJECT-TYPE
SYNTAX TruthValue
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The object is examined when
atmfVccTransmitTrafficDescriptorType or
atmfVccReceiveTrafficDescriptorType for the associated
connection is equal to atmfNoClpNoScr.
If this object is set to false(2), the network is requested
to apply the CBR.1 conformance definition. If this object
is set to true(1), the network is requested to apply the
UBR.1 conformance definition."
::= { atmfVccEntry 20 }
atmfVccTransmitFrameDiscard OBJECT-TYPE
SYNTAX TruthValue
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If set to true(1), this object indicates that the network
is requested to treat data for this connection (in the
transmit direction) as frames (e.g. AAL5 CPCS_PDU's) rather
than as individual cells. While the precise
implementation is network-specific, this treatment may
for example involve discarding entire frames during
congestion, rather than a few cells from many frames.
The default value is false(2)."
::= { atmfVccEntry 21 }
atmfVccReceiveFrameDiscard OBJECT-TYPE
SYNTAX TruthValue
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If set to true(1), this object indicates that the network
is requested to treat data for this connection (in the
receive direction) as frames (e.g. AAL5 CPCS_PDU's) rather
than as individual cells. While the precise
implementation is network-specific, this treatment may
for example involve discarding entire frames during
congestion, rather than a few cells from many frames.
The default value is false(2)."
::= { atmfVccEntry 22 }
atmfVccServiceCategory OBJECT-TYPE
SYNTAX AtmServiceCategory
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The service category of this virtual channel connection."
::= { atmfVccEntry 23 }
-- The Virtual Channel ABR Group
-- This group contains per-VCC information, support for which is optional.
--
-- Attributes of ABR Virtual Channel connections
atmfVccAbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfVccAbrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of operational parameters related to the ABR
virtual channel connections which cross this ATM
Interface. There is one entry in this table for each
ABR virtual channel connection.
Each virtual channel connection represented
in this table must also be represented by
an entry in the atmfVccTable."
::= { atmfVccAbrGroup 1 }
atmfVccAbrEntry OBJECT-TYPE
SYNTAX AtmfVccAbrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular ABR virtual channel connection."
INDEX { atmfVccAbrPortIndex, atmfVccAbrVpi, atmfVccAbrVci }
::= { atmfVccAbrTable 1 }
AtmfVccAbrEntry ::=
SEQUENCE {
atmfVccAbrPortIndex
INTEGER,
atmfVccAbrVpi
INTEGER,
atmfVccAbrVci
INTEGER,
atmfVccAbrTransmitIcr
INTEGER,
atmfVccAbrTransmitNrm
INTEGER,
atmfVccAbrTransmitTrm
INTEGER,
atmfVccAbrTransmitCdf
INTEGER,
atmfVccAbrTransmitRif
INTEGER,
atmfVccAbrTransmitRdf
INTEGER,
atmfVccAbrTransmitAdtf
INTEGER,
atmfVccAbrTransmitCrm
INTEGER
}
atmfVccAbrPortIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of identifying
the ATM Interface over which this message was received."
::= { atmfVccAbrEntry 1 }
atmfVccAbrVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this ABR Virtual Channel Connection at the
local ATM Interface. For virtual interfaces (i.e. Virtual Path
Connections), this value has no meaning and is set to zero "
::= { atmfVccAbrEntry 2 }
atmfVccAbrVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VCI value of this ABR Virtual Channel Connection at the
local ATM Interface."
::= { atmfVccAbrEntry 3 }
atmfVccAbrTransmitIcr OBJECT-TYPE
SYNTAX INTEGER (0..16777215)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Initial Cell Rate: This is the rate at which the
source starts, both initially and after an idle period.
The unit is cells per second. The value must not be
larger than PCR, and is usually lower."
::= { atmfVccAbrEntry 4 }
atmfVccAbrTransmitNrm OBJECT-TYPE
SYNTAX INTEGER {
nrm2(1),
nrm4(2),
nrm8(3),
nrm16(4),
nrm32(5),
nrm64(6),
nrm128(7),
nrm256(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of data cells a source may send
for each forward RM-cell. The default value is nrm32(5)."
::= { atmfVccAbrEntry 5 }
atmfVccAbrTransmitTrm OBJECT-TYPE
SYNTAX INTEGER {
trm0point78125(1),
trm1point5625(2),
trm3point125(3),
trm6point25(4),
trm12point5(5),
trm25(6),
trm50(7),
trm100(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Upper bound on the time between forward RM-cells for
an active source (in milliseconds). The default value
is trm100(8)."
::= { atmfVccAbrEntry 6 }
atmfVccAbrTransmitCdf OBJECT-TYPE
SYNTAX INTEGER {
cdf0(1),
cdfOneOver64(2),
cdfOneOver32(3),
cdfOneOver16(4),
cdfOneOver8(5),
cdfOneOver4(6),
cdfOneOver2(7),
cdfOne(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Cutoff Decrease Factor: This field controls the rate
decrease associated with lost or delayed backward RM
cells. Larger values result in faster rate decrease.
The default value is cdfOneOver16(4)."
::= { atmfVccAbrEntry 7 }
atmfVccAbrTransmitRif OBJECT-TYPE
SYNTAX INTEGER {
rifOneOver32768(1),
rifOneOver16384(2),
rifOneOver8192(3),
rifOneOver4096(4),
rifOneOver2048(5),
rifOneOver1024(6),
rifOneOver512(7),
rifOneOver256(8),
rifOneOver128(9),
rifOneOver64(10),
rifOneOver32(11),
rifOneOver16(12),
rifOneOver8(13),
rifOneOver4(14),
rifOneOver2(15),
rifOne(16)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Rate Increment Factor: Controls the rate at which the rate
increases, when a backward RM-cell is received with CI=0 and
NI=0. Larger values lead to faster rate increase. The default
value is rifOneOver16(12)."
::= { atmfVccAbrEntry 8 }
atmfVccAbrTransmitRdf OBJECT-TYPE
SYNTAX INTEGER {
rdfOneOver32768(1),
rdfOneOver16384(2),
rdfOneOver8192(3),
rdfOneOver4096(4),
rdfOneOver2048(5),
rdfOneOver1024(6),
rdfOneOver512(7),
rdfOneOver256(8),
rdfOneOver128(9),
rdfOneOver64(10),
rdfOneOver32(11),
rdfOneOver16(12),
rdfOneOver8(13),
rdfOneOver4(14),
rdfOneOver2(15),
rdfOne(16)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Rate Decrease Factor: Controls the rate decrease
which occurs when backward RM-cells with CI=1, are
received. Larger values lead to faster rate
decrease. The default value is rdfOneOver16(12)."
::= { atmfVccAbrEntry 9 }
atmfVccAbrTransmitAdtf OBJECT-TYPE
SYNTAX INTEGER (1..1023)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"ACR Decrease Time Factor: Time permitted between
sending RM-cells, before the allowed rate (ACR) is
decreased to ICR. Range is 10 ms to 10.23 seconds.
The unit is 10 milliseconds. For example, the default
value of 50 corresponds to a time factor of 500 ms.
Larger values allow a source to retain its current
rate longer, during periods of relative inactivity.
The default is 50 (0.5 seconds)."
::= { atmfVccAbrEntry 10 }
atmfVccAbrTransmitCrm OBJECT-TYPE
SYNTAX INTEGER (0..8388608)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"RM Cells Before Cutoff: Limits the number of forward
RM-cells which may be sent in the absence of received
backward RM-cells."
::= { atmfVccAbrEntry 11 }
-- Traps
atmfVpcChange TRAP-TYPE
ENTERPRISE atmForum
VARIABLES { atmfVpcPortIndex, atmfVpcVpi, atmfVpcOperStatus }
DESCRIPTION
"An atmfVpcChange trap indicates that a permanent VPC has been
added or deleted at this ATM Interface or that the attributes
of an existing VPC have been modified. The variables
included in the trap identify the VPI value of the
reconfigured VPC at this ATM Interface."
::= 1
atmfVccChange TRAP-TYPE
ENTERPRISE atmForum
VARIABLES { atmfVccPortIndex, atmfVccVci, atmfVccVpi,
atmfVccOperStatus }
DESCRIPTION
"An atmfVccChange trap indicates that a permanent VCC has been
added or deleted at this ATM Interface or that the attributes
of an existing VCC have been modified.. The variables
included in the trap identify the VCI and VPI values
of the reconfigured VCC at this ATM
Interface."
::= 2
-- The NetPrefix Group
--
-- The Network Prefix Table is implemented by the user-side IME.
-- This is hardcoded into UME... mgo, Xylan
--atmfNetPrefixTable OBJECT-TYPE
--SYNTAX SEQUENCE OF AtmfNetPrefixEntry
--ACCESS not-accessible
--STATUS mandatory
--DESCRIPTION
--"A table implemented by the user-side IME, containing the
--network-prefix(es) for ATM-layer addresses in effect on
--the user side of the UNI."
--::= { atmfNetPrefixGroup 1 }
--atmfNetPrefixEntry OBJECT-TYPE
--SYNTAX AtmfNetPrefixEntry
--ACCESS not-accessible
--STATUS mandatory
--DESCRIPTION
--"Information about a single network-prefix for
--ATM-layer addresses in effect on the user-side IME.
--Note that the index variable atmNetPrefixPrefix is a
--variable-length string, and as such the rule for
--variable-length strings in section 4.1.6 of RFC 1212
--applies."
--INDEX { atmfNetPrefixPort, atmfNetPrefixPrefix }
--::= { atmfNetPrefixTable 1 }
--AtmfNetPrefixEntry ::=
--SEQUENCE {
--atmfNetPrefixPort
--INTEGER,
--atmfNetPrefixPrefix
--NetPrefix,
--atmfNetPrefixStatus
--INTEGER
--}
--atmfNetPrefixPort OBJECT-TYPE
--SYNTAX INTEGER (0..2147483647)
--ACCESS not-accessible
--STATUS mandatory
--DESCRIPTION
--"A unique value which identifies the UNI port for
--which the network prefix for ATM addresses is in
--effect. The value of 0 has the special meaning of
--identifying the local UNI."
--::= { atmfNetPrefixEntry 1 }
--
--atmfNetPrefixPrefix OBJECT-TYPE
--SYNTAX NetPrefix
--ACCESS not-accessible
--STATUS mandatory
--DESCRIPTION
--"The network prefix for ATM addresses which is in
--effect on the user side of the ATM UNI port."
--::= { atmfNetPrefixEntry 2 }
--
--atmfNetPrefixStatus OBJECT-TYPE
--SYNTAX INTEGER { valid(1), invalid(2) }
--ACCESS read-write
--STATUS mandatory
--DESCRIPTION
--"An indication of the validity of the network prefix
--for ATM addresses on the user side of the UNI port.
--To configure a new network prefix in this table, the
--network-side IME must set the appropriate instance of this
--object to the value valid(1). To delete an existing
--network prefix in this table, the network-side IME must
--set the appropriate instance of this object to the
--value invalid(2).
--
--If circumstances occur on the user-side IME which cause a
--prefix to become invalid, the user-side IME modifies the
--value of the appropriate instance of this object to invalid(2).
--
--Whenever the value of this object for a particular
--prefix becomes invalid(2), the conceptual row for that
--prefix may be removed from the table at any time,
--either immediately or subsequently."
--::= { atmfNetPrefixEntry 3 }
--
--
-- The Address Group
--
-- The Address Table is implemented by the network-side IME.
--
atmfAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfAddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table implemented by the network-side IME, containing the
ATM-layer addresses in effect on the user side of the UNI."
::= { atmfAddressGroup 1 }
atmfAddressEntry OBJECT-TYPE
SYNTAX AtmfAddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about a single ATM-layer address in effect
on the user-side IME. Note that the index variable
atmAddressAtmAddress is a variable-length string, and as
such the rule for variable-length strings in section
4.1.6 of RFC 1212 applies."
INDEX { atmfAddressPort, atmfAddressAtmAddress }
::= { atmfAddressTable 1 }
AtmfAddressEntry ::=
SEQUENCE {
atmfAddressPort
INTEGER,
atmfAddressAtmAddress
AtmAddress,
atmfAddressStatus
INTEGER,
atmfAddressOrgScope
INTEGER
}
atmfAddressPort OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A unique value which identifies the UNI port for
which the ATM address is in effect. The value of 0
has the special meaning of identifying the local UNI."
::= { atmfAddressEntry 1 }
atmfAddressAtmAddress OBJECT-TYPE
SYNTAX AtmAddress
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The ATM address which is in effect on the user side
of the ATM UNI port."
::= { atmfAddressEntry 2 }
atmfAddressStatus OBJECT-TYPE
SYNTAX INTEGER { valid(1), invalid(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An indication of the validity of the ATM address at
the user side of the UNI port. To configure a new
address in this table, the user-side IME must set the
appropriate instance of this object to the value
valid(1). To delete an existing address in this table,
the user-side IME must set the appropriate instance of
this object to the value invalid(2).
If circumstances occur on the network-side IME which cause
an address to become invalid, the network-side IME
modifies the value of the appropriate instance of this
object to invalid(2).
Whenever the value of this object for a particular
address becomes invalid(2), the conceptual row for
that address may be removed from the table at any
time, either immediately or subsequently."
::= { atmfAddressEntry 3 }
atmfAddressOrgScope OBJECT-TYPE
SYNTAX INTEGER {
localNetwork(1),
localNetworkPlusOne(2),
localNetworkPlusTwo(3),
siteMinusOne(4),
intraSite(5),
sitePlusOne(6),
organizationMinusOne(7),
intraOrganization(8),
organizationPlusOne(9),
communityMinusOne(10),
intraCommunity(11),
communityPlusOne(12),
regional(13),
interRegional(14),
global(15)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object indicates the organizational
scope for the referenced address. The information of
the referenced address shall not be distributed
outside the indicated scope. If the user-side IME does
not specify a value for the atmfAddressOrgScope object,
the network shall set the value of this object to
localNetwork(1), if the registered address is an ATM group
address, or to global(15), if the registered address is
an individual address. Refer to Annex 6.0
of ATM Forum UNI Signalling 4.0 for guidelines regarding
the use of organizational scopes.
This organization hierarchy may be mapped to ATM network's
routing hierarchy such as PNNI's routing level and
the mapping shall be configurable in
nodes. Use of this object in a public network is for
further study.
The default values for organizational scope are
localNetwork(1) for ATM group addresses, and global(15)
for individual addresses."
::= { atmfAddressEntry 4 }
-- The Address Registration Admin Group
--
-- The Address Registration Admin Table is mandatory for all IMEs.
atmfAddressRegistrationAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfAddressRegistrationAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of Address Registration administrative
information for the ATM Interface."
::= { atmfAddressRegistrationAdminGroup 1 }
atmfAddressRegistrationAdminEntry OBJECT-TYPE
SYNTAX AtmfAddressRegistrationAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing Address
Registration administrative information for the ATM
Interface."
INDEX { atmfAddressRegistrationAdminIndex }
::= { atmfAddressRegistrationAdminTable 1 }
AtmfAddressRegistrationAdminEntry ::=
SEQUENCE {
atmfAddressRegistrationAdminIndex
INTEGER,
atmfAddressRegistrationAdminStatus
INTEGER
}
atmfAddressRegistrationAdminIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfAddressRegistrationAdminEntry 1 }
atmfAddressRegistrationAdminStatus OBJECT-TYPE
SYNTAX INTEGER { supported(1), unsupported(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indication of whether or not Address Registration
is supported on this ATM Interface. Supported(1)
indicates that this ATM Interface supports address
registration. Unsupported(2) indicates that this ATM
Interface does not support address registration."
::= { atmfAddressRegistrationAdminEntry 2 }
-- Object Identifier definitions
-- The following values are defined for use as possible values
-- of the atmfSrvcRegServiceID object.
-- LAN Emulation Configuration Server (LECS)
atmfSrvcRegLecs OBJECT IDENTIFIER ::= { atmfSrvcRegTypes 1 }
-- When atmfSrvcRegServiceID has a value of atmfSrvcRegLecs,
-- the value of atmfSrvcRegParm1 is ignored.
-- ATM Name Server (ANS)
atmfSrvcRegAns OBJECT IDENTIFIER ::= { atmfSrvcRegTypes 2 }
-- When atmfSrvcRegServiceID has a value of atmfSrvcRegAns,
-- the value of atmfSrvcRegParm1 is ignored.
-- The Service Registry Table
--
-- The Service Registry Table is implemented by the network-side IME
atmfSrvcRegTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmfSrvcRegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table implemented by the IME on the network side of
the ATM UNI port contains all of the services that are
available to the user-side IME indexed by service
identifier."
::= { atmfSrvcRegistryGroup 1 }
atmfSrvcRegEntry OBJECT-TYPE
SYNTAX AtmfSrvcRegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Information about a single service provider that is
available to the user-side IME."
INDEX { atmfSrvcRegPort, atmfSrvcRegServiceID,
atmfSrvcRegAddressIndex }
::= { atmfSrvcRegTable 1 }
AtmfSrvcRegEntry ::=
SEQUENCE {
atmfSrvcRegPort
INTEGER,
atmfSrvcRegServiceID
OBJECT IDENTIFIER,
atmfSrvcRegATMAddress
AtmAddress,
atmfSrvcRegAddressIndex
INTEGER,
atmfSrvcRegParm1
OCTET STRING
}
atmfSrvcRegPort OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The value of 0 which has the special meaning of
identifying the ATM Interface over which this message
was received."
::= { atmfSrvcRegEntry 1 }
atmfSrvcRegServiceID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This is the service identifier which uniquely identifies
the type of service at the address provided in the table."
::= { atmfSrvcRegEntry 2 }
atmfSrvcRegATMAddress OBJECT-TYPE
SYNTAX AtmAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the full address of the service. The user-side
IME may use this address to establish a connection
with the service."
::= { atmfSrvcRegEntry 3 }
atmfSrvcRegAddressIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An arbitrary integer to differentiate multiple rows
containing different ATM addresses for the same service
on the same port."
::= { atmfSrvcRegEntry 4 }
atmfSrvcRegParm1 OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..255))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An octet string whose size and meaning is determined
by the value of atmfSrvcRegServiceID."
::= { atmfSrvcRegEntry 5 }
END
Reference in New Issue Copy Permalink