mibs/MIBS/brother/BROTHER-MIB

12180 lines
272 KiB
Plaintext
Raw Normal View History

2023-12-05 12:25:34 +01:00
-- Brother MIB
-- (C) Copyright 1999-2009 Brother Industries, Ltd. All rights reserved
-- ver.091.1
-- BROTHER OBJECT IDENTIFIER ::= { iso org(3) dod(6) internet(1) private(4) enterprises(1) 2435 }
BROTHER-MIB DEFINITIONS ::= BEGIN
IMPORTS
enterprises, IpAddress, Counter
FROM RFC1155-SMI
DisplayString
FROM RFC1213-MIB
DateAndTime
FROM SNMPv2-TC
OBJECT-TYPE
FROM RFC-1212
Ipv6Address
FROM IPV6-TC;
brother OBJECT IDENTIFIER ::= { enterprises 2435 }
nm OBJECT IDENTIFIER ::= { brother 2 }
system OBJECT IDENTIFIER ::= { nm 3 }
interface OBJECT IDENTIFIER ::= { nm 4 }
net-peripheral OBJECT IDENTIFIER ::= { system 9 }
net-printer OBJECT IDENTIFIER ::= { net-peripheral 1 }
net-MFP OBJECT IDENTIFIER ::= { net-peripheral 2 }
netPML OBJECT IDENTIFIER ::= { net-peripheral 4 }
generalDeviceStatus OBJECT IDENTIFIER ::= { net-printer 1 }
fax-setup OBJECT IDENTIFIER ::= { net-MFP 1 }
scanner-setup OBJECT IDENTIFIER ::= { net-MFP 11 }
mfpCapability OBJECT IDENTIFIER ::= { net-MFP 101 }
mfpgeneral-setup OBJECT IDENTIFIER ::= { net-MFP 111 }
netPMLmgmt OBJECT IDENTIFIER ::= { netPML 2 }
status OBJECT IDENTIFIER ::= { generalDeviceStatus 2 }
autodial OBJECT IDENTIFIER ::= { fax-setup 1 }
fax-general OBJECT IDENTIFIER ::= { fax-setup 2 }
onetouchDial OBJECT IDENTIFIER ::= { autodial 1 }
speedDial OBJECT IDENTIFIER ::= { autodial 2 }
scanToInfo OBJECT IDENTIFIER ::= { scanner-setup 1 }
mcGeneral OBJECT IDENTIFIER ::= { mfpCapability 1 }
mcFax OBJECT IDENTIFIER ::= { mfpCapability 2 }
mcScanner OBJECT IDENTIFIER ::= { mfpCapability 3 }
mcgRemoteSetup OBJECT IDENTIFIER ::= { mcGeneral 11 }
mcfGeneral OBJECT IDENTIFIER ::= { mcFax 1 }
mcfNetFaxShare OBJECT IDENTIFIER ::= { mcFax 11 }
mcfNetPcFaxRx OBJECT IDENTIFIER ::= { mcFax 12 }
mcfFaxInfomation OBJECT IDENTIFIER ::= { mcFax 101 }
mcsNetScanner OBJECT IDENTIFIER ::= { mcScanner 11 }
mcsNetSKy OBJECT IDENTIFIER ::= { mcScanner 12 }
tonerlow OBJECT IDENTIFIER ::= { status 10 }
device OBJECT IDENTIFIER ::= { netPMLmgmt 1 }
destination-subsystem1 OBJECT IDENTIFIER ::= { device 1 }
sleep OBJECT IDENTIFIER ::= { destination-subsystem1 1 }
autoc OBJECT IDENTIFIER ::= { destination-subsystem1 2 }
simm OBJECT IDENTIFIER ::= { destination-subsystem1 4 }
specification OBJECT IDENTIFIER ::= { simm 1 }
simmkind0 OBJECT IDENTIFIER ::= { specification 1 }
simmkind1 OBJECT IDENTIFIER ::= { specification 2 }
simmkind2 OBJECT IDENTIFIER ::= { specification 3 }
simmkind3 OBJECT IDENTIFIER ::= { specification 4 }
bio1-explanation OBJECT IDENTIFIER ::= { simm 3 }
determined OBJECT IDENTIFIER ::= { bio1-explanation 1 }
destination-subsystem2 OBJECT IDENTIFIER ::= { device 2 }
printerjob OBJECT IDENTIFIER ::= { destination-subsystem2 1 }
jobend OBJECT IDENTIFIER ::= { printerjob 1 }
destination-subsystem3 OBJECT IDENTIFIER ::= { device 3 }
prt-setup OBJECT IDENTIFIER ::= { destination-subsystem3 3 }
prt-condition OBJECT IDENTIFIER ::= { prt-setup 1 }
destination-subsystem4 OBJECT IDENTIFIER ::= { device 4 }
print-engine OBJECT IDENTIFIER ::= { destination-subsystem4 1 }
prt-density OBJECT IDENTIFIER ::= { print-engine 1 }
status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 }
tray OBJECT IDENTIFIER ::= { print-engine 3 }
economy OBJECT IDENTIFIER ::= { print-engine 6 }
manual OBJECT IDENTIFIER ::= { tray 1 }
traysize OBJECT IDENTIFIER ::= { tray 3 }
mp OBJECT IDENTIFIER ::= { traysize 1 }
cassette OBJECT IDENTIFIER ::= { traysize 2 }
cassette2 OBJECT IDENTIFIER ::= { traysize 3 }
cassette3 OBJECT IDENTIFIER ::= { traysize 4 }
cassette4 OBJECT IDENTIFIER ::= { traysize 5 }
brorg OBJECT IDENTIFIER ::= { device 5 }
printersetup OBJECT IDENTIFIER ::= { brorg 1 }
pagesetup OBJECT IDENTIFIER ::= { brorg 2 }
fontsetup OBJECT IDENTIFIER ::= { brorg 3 }
controlpanel OBJECT IDENTIFIER ::= { brorg 4 }
printerinfomation OBJECT IDENTIFIER ::= { brorg 5 }
printerstatus OBJECT IDENTIFIER ::= { brorg 6 }
secret OBJECT IDENTIFIER ::= { brorg 7 }
adminsetting OBJECT IDENTIFIER ::= { brorg 8 }
general OBJECT IDENTIFIER ::= { printersetup 1 }
advanced OBJECT IDENTIFIER ::= { printersetup 2 }
mail OBJECT IDENTIFIER ::= { printersetup 3 }
finisher OBJECT IDENTIFIER ::= { printersetup 4 }
catch-tray OBJECT IDENTIFIER ::= { printersetup 5 }
autoff OBJECT IDENTIFIER ::= { advanced 7 }
buzzer OBJECT IDENTIFIER ::= { advanced 22 }
smallPaperSize OBJECT IDENTIFIER ::= { advanced 51 }
trayPriority OBJECT IDENTIFIER ::= { advanced 52 }
carbonCopy OBJECT IDENTIFIER ::= { advanced 53 }
mediaFix OBJECT IDENTIFIER ::= { advanced 54 }
directprint OBJECT IDENTIFIER ::= { advanced 60 }
pictbridge OBJECT IDENTIFIER ::= { advanced 61 }
colorcorrection OBJECT IDENTIFIER ::= { advanced 62 }
pcl OBJECT IDENTIFIER ::= { pagesetup 1 }
ps OBJECT IDENTIFIER ::= { pagesetup 2 }
gl OBJECT IDENTIFIER ::= { pagesetup 3 }
epson OBJECT IDENTIFIER ::= { pagesetup 4 }
ibm OBJECT IDENTIFIER ::= { pagesetup 5 }
margin-p OBJECT IDENTIFIER ::= { pcl 1 }
auto-p OBJECT IDENTIFIER ::= { pcl 2 }
pen1 OBJECT IDENTIFIER ::= { gl 1 }
pen2 OBJECT IDENTIFIER ::= { gl 2 }
pen3 OBJECT IDENTIFIER ::= { gl 3 }
pen4 OBJECT IDENTIFIER ::= { gl 4 }
pen5 OBJECT IDENTIFIER ::= { gl 5 }
pen6 OBJECT IDENTIFIER ::= { gl 6 }
margin-e OBJECT IDENTIFIER ::= { epson 1 }
auto-e OBJECT IDENTIFIER ::= { epson 2 }
margin-i OBJECT IDENTIFIER ::= { ibm 1 }
auto-i OBJECT IDENTIFIER ::= { ibm 2 }
reset OBJECT IDENTIFIER ::= { controlpanel 1 }
test OBJECT IDENTIFIER ::= { controlpanel 2 }
panellock OBJECT IDENTIFIER ::= { controlpanel 3 }
key OBJECT IDENTIFIER ::= { controlpanel 4 }
panelinfo OBJECT IDENTIFIER ::= { controlpanel 5 }
version OBJECT IDENTIFIER ::= { printerinfomation 3 }
errorHistory OBJECT IDENTIFIER ::= { printerinfomation 51 }
printPages OBJECT IDENTIFIER ::= { printerinfomation 52 }
capability OBJECT IDENTIFIER ::= { printerinfomation 53 }
countinfo OBJECT IDENTIFIER ::= { printerinfomation 54 }
copies OBJECT IDENTIFIER ::= { capability 1 }
orientation OBJECT IDENTIFIER ::= { capability 2 }
paper OBJECT IDENTIFIER ::= { capability 3 }
mediatype OBJECT IDENTIFIER ::= { capability 4 }
resolution OBJECT IDENTIFIER ::= { capability 5 }
pfkit OBJECT IDENTIFIER ::= { countinfo 1 }
scancount OBJECT IDENTIFIER ::= { countinfo 2 }
clockfunction OBJECT IDENTIFIER ::= { adminsetting 1 }
npCard OBJECT IDENTIFIER ::= { interface 3 }
npSys OBJECT IDENTIFIER ::= { npCard 1 }
npConfig OBJECT IDENTIFIER ::= { npSys 1 }
adminCapa OBJECT IDENTIFIER ::= { npSys 99 }
userSetting OBJECT IDENTIFIER ::= { npSys 100 }
verify OBJECT IDENTIFIER ::= { npSys 101 }
npTcp OBJECT IDENTIFIER ::= { npCard 6 }
lpd OBJECT IDENTIFIER ::= { npTcp 99 }
banner OBJECT IDENTIFIER ::= { lpd 1 }
npCtl OBJECT IDENTIFIER ::= { npCard 7 }
etherN OBJECT IDENTIFIER ::= { npCtl 99 }
eNet OBJECT IDENTIFIER ::= { etherN 1 }
npPort OBJECT IDENTIFIER ::= { npCard 13 }
funa OBJECT IDENTIFIER ::= { npPort 10 }
npSet OBJECT IDENTIFIER ::= { npCard 99 }
dns OBJECT IDENTIFIER ::= { npSet 1 }
pushstatus OBJECT IDENTIFIER ::= { npSet 2 }
pjl OBJECT IDENTIFIER ::= { npSet 3 }
eMailReports OBJECT IDENTIFIER ::= { npSet 4 }
pjlinfo OBJECT IDENTIFIER ::= { pjl 1 }
priadmin OBJECT IDENTIFIER ::= { pushstatus 2 }
secadmin OBJECT IDENTIFIER ::= { pushstatus 3 }
brnetConfig OBJECT IDENTIFIER ::= { npCard 1240 }
brconfig OBJECT IDENTIFIER ::= { brnetConfig 1 }
brcontrol OBJECT IDENTIFIER ::= { brnetConfig 2 }
brport OBJECT IDENTIFIER ::= { brnetConfig 3 }
brservice OBJECT IDENTIFIER ::= { brnetConfig 4 }
brprotocol OBJECT IDENTIFIER ::= { brnetConfig 5 }
brfirmware OBJECT IDENTIFIER ::= { brnetConfig 6 }
brlat OBJECT IDENTIFIER ::= { brprotocol 1 }
brtcpip OBJECT IDENTIFIER ::= { brprotocol 2 }
brnetware OBJECT IDENTIFIER ::= { brprotocol 3 }
brappletalk OBJECT IDENTIFIER ::= { brprotocol 4 }
brbanyan OBJECT IDENTIFIER ::= { brprotocol 5 }
bremail OBJECT IDENTIFIER ::= { brprotocol 6 }
brdlc OBJECT IDENTIFIER ::= { brprotocol 7 }
brnetbeui OBJECT IDENTIFIER ::= { brprotocol 8 }
bripp OBJECT IDENTIFIER ::= { brprotocol 9 }
brntsend OBJECT IDENTIFIER ::= { brprotocol 10 }
brnetConfigOpt OBJECT IDENTIFIER ::= { npCard 2435 }
broriginalprotocol OBJECT IDENTIFIER ::= { brnetConfigOpt 5 }
broriginaltcpip OBJECT IDENTIFIER ::= { broriginalprotocol 2 }
broriginalftp OBJECT IDENTIFIER ::= { broriginalprotocol 10 }
broriginalupnp OBJECT IDENTIFIER ::= { broriginalprotocol 11 }
broriginalapipa OBJECT IDENTIFIER ::= { broriginalprotocol 12 }
broriginalmdns OBJECT IDENTIFIER ::= { broriginalprotocol 13 }
broriginalLAA OBJECT IDENTIFIER ::= { broriginalprotocol 14 }
broriginalIPv6 OBJECT IDENTIFIER ::= { broriginalprotocol 15 }
broriginaltelnet OBJECT IDENTIFIER ::= { broriginalprotocol 16 }
broriginalEWS OBJECT IDENTIFIER ::= { broriginalprotocol 17 }
broriginalSNMP OBJECT IDENTIFIER ::= { broriginalprotocol 18 }
broriginalldap OBJECT IDENTIFIER ::= { broriginalprotocol 19 }
broriginalTFTP OBJECT IDENTIFIER ::= { broriginalprotocol 20 }
broriginalHTTPS OBJECT IDENTIFIER ::= { broriginalprotocol 21 }
broriginalLPD OBJECT IDENTIFIER ::= { broriginalprotocol 22 }
broriginalRawPort OBJECT IDENTIFIER ::= { broriginalprotocol 23 }
broriginalLLTD OBJECT IDENTIFIER ::= { broriginalprotocol 24 }
broriginalWebServices OBJECT IDENTIFIER ::= { broriginalprotocol 25 }
broriginalLLMNR OBJECT IDENTIFIER ::= { broriginalprotocol 26 }
broriginalSecurity OBJECT IDENTIFIER ::= { broriginalprotocol 100 }
broriginalinternetsetting OBJECT IDENTIFIER ::= { brnetConfigOpt 10 }
broriginalproxy OBJECT IDENTIFIER ::= { broriginalinternetsetting 1 }
broriginalOtherSetting OBJECT IDENTIFIER ::= { brnetConfigOpt 20 }
broriginalJobTermination OBJECT IDENTIFIER ::= { broriginalOtherSetting 1 }
broriginalSNMPTrap OBJECT IDENTIFIER ::= { broriginalOtherSetting 2 }
broriginalLegacy OBJECT IDENTIFIER ::= { broriginalOtherSetting 3 }
brSecurityGeneralStatus OBJECT IDENTIFIER ::= { broriginalSecurity 1 }
brSecurityGeneralSetup OBJECT IDENTIFIER ::= { broriginalSecurity 2 }
brSecurityDeviceNegotiation OBJECT IDENTIFIER ::= { broriginalSecurity 10 }
wireless OBJECT IDENTIFIER ::= { npCard 100 }
wlInfo OBJECT IDENTIFIER ::= { wireless 1 }
wlCapability OBJECT IDENTIFIER ::= { wlInfo 1 }
wlGeneralInfo OBJECT IDENTIFIER ::= { wlInfo 2 }
wlNetSearch OBJECT IDENTIFIER ::= { wlInfo 11 }
wlAOSS OBJECT IDENTIFIER ::= { wlInfo 12 }
wlSES OBJECT IDENTIFIER ::= { wlInfo 13 }
wlWPS OBJECT IDENTIFIER ::= { wlInfo 14 }
wlSetup OBJECT IDENTIFIER ::= { wireless 11 }
wlGeneral OBJECT IDENTIFIER ::= { wlSetup 1 }
wlAdvanced OBJECT IDENTIFIER ::= { wlSetup 5 }
wlAssociate OBJECT IDENTIFIER ::= { wlSetup 11 }
wlWEP OBJECT IDENTIFIER ::= { wlAssociate 101 }
wlWPA OBJECT IDENTIFIER ::= { wlAssociate 102 }
wlTKIP OBJECT IDENTIFIER ::= { wlAssociate 103 }
wlLEAP OBJECT IDENTIFIER ::= { wlAssociate 104 }
wlStatus OBJECT IDENTIFIER ::= { wireless 21 }
wlGeneralStatus OBJECT IDENTIFIER ::= { wlStatus 1 }
npMultiCards OBJECT IDENTIFIER ::= { interface 4 }
npMultiIFSet OBJECT IDENTIFIER ::= { npMultiCards 99 }
brMultiIFdns OBJECT IDENTIFIER ::= { npMultiIFSet 1 }
brnetMultiIFConfig OBJECT IDENTIFIER ::= { npMultiCards 1240 }
brMultiIFconfig OBJECT IDENTIFIER ::= { brnetMultiIFConfig 1 }
brMultiIFcontrol OBJECT IDENTIFIER ::= { brnetMultiIFConfig 2 }
brMultiIFservice OBJECT IDENTIFIER ::= { brnetMultiIFConfig 4 }
brMultiIFprotocol OBJECT IDENTIFIER ::= { brnetMultiIFConfig 5 }
brMultiIFtcpip OBJECT IDENTIFIER ::= { brMultiIFprotocol 2 }
brMultiIFnetbeui OBJECT IDENTIFIER ::= { brMultiIFprotocol 8 }
brMultiIForiginalapipa OBJECT IDENTIFIER ::= { brMultiIFprotocol 12 }
brMultiIForiginalLAA OBJECT IDENTIFIER ::= { brMultiIFprotocol 14 }
brMultiIForiginalIPv6 OBJECT IDENTIFIER ::= { brMultiIFprotocol 15 }
brMultiIForiginalWebServices OBJECT IDENTIFIER ::= { brMultiIFprotocol 16 }
funclock OBJECT IDENTIFIER ::= { advanced 63 }
broriginalKerberos OBJECT IDENTIFIER ::= { broriginalprotocol 27 }
broriginalCIFS OBJECT IDENTIFIER ::= { broriginalprotocol 28 }
broriginalSNTP OBJECT IDENTIFIER ::= { broriginalprotocol 29 }
firmwareupdatekeyword OBJECT IDENTIFIER ::= { printerinfomation 55 }
autocountreset OBJECT IDENTIFIER ::= { funclock 31 }
wlSimpleWizard OBJECT IDENTIFIER ::= { wlInfo 15 }
brJamPlace OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Location of JAM.
0:No Jam
1:Jam Trays
2:Jam Inside
3:Jam Rear
4:Jam Duplex unit"
::= { status 9 }
brToner1Low OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Black Toner status.
0:Toner Full
1:Toner Low
2:No Toner Cartridge
3:Toner Empty"
::= { tonerlow 1 }
brToner2Low OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Cyan Toner status.
0:Toner Ready
1:Toner Low
2:No Toner Cartridge
3:Toner Empty"
::= { tonerlow 2 }
brToner3Low OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Magenta Toner status.
0:Toner Ready
1:Toner Low
2:No Toner Cartridge
3:Toner Empty"
::= { tonerlow 3 }
brToner4Low OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Yellow Toner status.
0:Toner Ready
1:Toner Low
2:No Toner Cartridge
3:Toner Empty"
::= { tonerlow 4 }
brieee1284id OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IEEE1284 device ID"
::= { generalDeviceStatus 7 }
brttt1 OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused"
::= { generalDeviceStatus 10 }
brOneTouchDialCount OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of One touch dial."
::= { onetouchDial 1 }
brOneTouchDialTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrOneTouchDialEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents One touch dial."
::= { onetouchDial 2 }
brOneTouchDialEntry OBJECT-TYPE
SYNTAX BrOneTouchDialEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the OneTouchDial table. Rows cannot be created or deleted."
INDEX { brOneTouchDialIndex }
::= { brOneTouchDialTable 1 }
BrOneTouchDialEntry ::=
SEQUENCE {
brOneTouchDialIndex
INTEGER,
brOneTouchDialData
OCTET STRING
}
brOneTouchDialIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The One touch dial number."
::= { brOneTouchDialEntry 1 }
brOneTouchDialData OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The One Touch dial data."
::= { brOneTouchDialEntry 2 }
brSpeedDialCount OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Speed dial."
::= { speedDial 1 }
brSpeedDialTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrSpeedDialEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Speed dial."
::= { speedDial 2 }
brSpeedDialEntry OBJECT-TYPE
SYNTAX BrSpeedDialEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the speedDial table. Rows cannot be created or deleted."
INDEX { brSpeedDialIndex }
::= { brSpeedDialTable 1 }
BrSpeedDialEntry ::=
SEQUENCE {
brSpeedDialIndex
INTEGER,
brSpeedDialData
OCTET STRING
}
brSpeedDialIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Speed dial number."
::= { brSpeedDialEntry 1 }
brSpeedDialData OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Speed dial Data."
::= { brSpeedDialEntry 2 }
brDialDataAllClear OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Clear the all data of Onetouch dial and Speed dial."
::= { autodial 3 }
brFaxReceiveMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Fax Receive Mode
0:Auto
1:Manual
2:FaxTel
3:TAD"
::= { fax-general 1 }
brRingDelayCount OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Ring Delay Count"
::= { fax-general 2 }
brOwnFaxNumber OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Own Fax Number"
::= { fax-general 3 }
brRegisterKeyInfo OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Add the ScanTo information.
If device receives GET request, device should reply fix value
TRUE(writable), FALSE(not writable) to the client."
::= { scanToInfo 1 }
brUnRegisterKeyInfo OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Remove the ScanTo information.
If device receives GET request, device should reply fix value
TRUE (writable), FALSE (not writable) to the client."
::= { scanToInfo 2 }
brNetSKeyReceiverAddress OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..63) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IP Address or the name of the S-Key Receiver."
::= { scanToInfo 5 }
brNetRemoteSetUpSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Net Remote Setup function is not supported.
1 indicates the Net Remote Setup function is implemented by the firmware"
::= { mcgRemoteSetup 1 }
brNetRemoteSetUpEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Net Remote Setup is not enabled.
1 indicates that the Net Remote Setup is enabled.
Writing a non-zero value will enable the Net Remote Setup
if it is supported by the firmware."
::= { mcgRemoteSetup 2 }
brFaxSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Fax function is not supported.
1 indicates the Fax function is implemented by the firmware"
::= { mcfGeneral 1 }
brIFaxSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the IFax function is not supported.
1 indicates the IFax function is implemented by the firmware"
::= { mcfGeneral 3 }
brNetFaxShareSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Net Fax Share is not supported.
1 indicates the Net Fax Share is implemented by the firmware"
::= { mcfNetFaxShare 1 }
brNetFaxShareEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Net Fax Share is not enabled.
1 indicates that the Net Fax Share is enabled.
Writing a non-zero value will enable the Net Fax Share
if it is supported by the firmware."
::= { mcfNetFaxShare 2 }
brNetPcFaxRxSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Net PC Fax Rx is not supported.
1 indicates the Net PC Fax Rx is implemented by the firmware"
::= { mcfNetPcFaxRx 1 }
brNetPcFaxRxEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Net PC Fax Rx is not enabled.
1 indicates that the Net PC Fax Rx is enabled.
Writing a non-zero value will enable the Net PC Fax Rx
if it is supported by the firmware."
::= { mcfNetPcFaxRx 2 }
brNetRegisterPcFaxInfo OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Add the PcFax information.
If device receives GET request, device should reply fix value
TRUE(writable), FALSE(not writable) to the client."
::= { mcfNetPcFaxRx 3 }
brPhoneNumberLastFax OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..20) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Phone Number of Last Fax"
::= { mcfFaxInfomation 1 }
brPagesSentLastFax OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Pages Sent in Last Fax"
::= { mcfFaxInfomation 2 }
brTimestampLastFax OBJECT-TYPE
SYNTAX DateAndTime
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Timestamp of Last Fax"
::= { mcfFaxInfomation 3 }
brFaxHeaderInfo OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..50) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Fax Header Infomation"
::= { mcfFaxInfomation 4 }
brNetScannerSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Net Scanner is not supported.
1 indicates the Net Scanner is implemented by the firmware"
::= { mcsNetScanner 1 }
brNetScannerEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Net Scanner is not enabled.
1 indicates that the Net Scanner is enabled.
Writing a non-zero value will enable the Net Scanner
if it is supported by the firmware."
::= { mcsNetScanner 2 }
brNetSKeySupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Net S-Key is not supported.
1 indicates the Net S-Key is implemented by the firmware"
::= { mcsNetSKy 1 }
brNetSKeyEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Net S-Key is not enabled.
1 indicates that the Net S-Key is enabled.
Writing a non-zero value will enable the Net S-Key
if it is supported by the firmware."
::= { mcsNetSKy 2 }
brServiceMode OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Service Mode"
::= { mfpgeneral-setup 1 }
brLockMode OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lock Mode
0:normal
1:Customer
2:Lock"
::= { mfpgeneral-setup 2 }
brActivityReportSetting OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Activity Report Setting
0:off
1:every 1hour
3:every 3hour
6:every 6hour
12:every 12hour
24:every 24hour
48:every 2day
96:every 4day
240:every Sunday
241:every Monday
242:every Tueseday
243:every Wednesday
244:every Thurseday
245:every Friday
246:every Saturday
255:interval 50FAX"
::= { mfpgeneral-setup 3 }
brpowerstime OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PowerSave Timeout value. 1 to 2147483647 (sec)"
::= { sleep 1 }
brautocont OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Auto Continue.
1:Off
2:On"
::= { autoc 7 }
brsimmtype0 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM type on slot0.
0: unconfirmed : 0 MB
1: empty
2: unconfirmed
3: No Supported : 0 MB
4: Read Only Memory
5: Volatility RAM : size MB
6: Un Volatility RAM : size MB
7: Flash Memory : size MB
8: Disk Drive : 0 MB
9: RAM/ROM : 0MB
10: Loading Paper Device
11: Out Paper Device
12: unconfirmed : 0 MB ato ha onaji"
::= { simmkind0 4 }
brsimmsize0 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM size on slot0"
::= { simmkind0 5 }
brsimmtype1 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM type on slot1.
0: unconfirmed : 0 MB
1: empty
2: unconfirmed
3: No Supported : 0 MB
4: Read Only Memory
5: Volatility RAM : size MB
6: Un Volatility RAM : size MB
7: Flash Memory : size MB
8: Disk Drive : 0 MB
9: RAM/ROM : 0MB
10: Loading Paper Device
11: Out Paper Device
12: unconfirmed : 0 MB ato ha onaji"
::= { simmkind1 4 }
brsimmsize1 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM size on slot1"
::= { simmkind1 5 }
brsimmtype2 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM type on slot2.
0: unconfirmed : 0 MB
1: empty
2: unconfirmed
3: No Supported : 0 MB
4: Read Only Memory
5: Volatility RAM : size MB
6: Un Volatility RAM : size MB
7: Flash Memory : size MB
8: Disk Drive : 0 MB
9: RAM/ROM : 0MB
10: Loading Paper Device
11: Out Paper Device
12: unconfirmed : 0 MB ato ha onaji"
::= { simmkind2 4 }
brsimmsize2 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM size on slot2."
::= { simmkind2 5 }
brsimmtype3 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM type on slot3.
0: unconfirmed : 0 MB
1: empty
2: unconfirmed
3: No Supported : 0 MB
4: Read Only Memory
5: Volatility RAM : size MB
6: Un Volatility RAM : size MB
7: Flash Memory : size MB
8: Disk Drive : 0 MB
9: RAM/ROM : 0MB
10: Loading Paper Device
11: Out Paper Device
12: unconfirmed : 0 MB ato ha onaji"
::= { simmkind3 4 }
brsimmsize3 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SIMM type on slot3."
::= { simmkind3 5 }
brTBD1 OBJECT-TYPE
SYNTAX INTEGER (1..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { determined 4 }
brtimeout OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Job Timeout. 1 to 2147483647(sec)"
::= { jobend 1 }
brTBD2 OBJECT-TYPE
SYNTAX INTEGER (1..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { jobend 5 }
brpersonality OBJECT-TYPE
SYNTAX INTEGER {
pcl(1),
hpgl(2),
ps(4),
auto(5),
ibm(6),
epson(7),
hbp(8)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Printer Emulation setting.
1:PCL
2:HPGL
4:PS
5:AUTO
6:IBM
7:EPSON
8:HBP"
::= { prt-condition 1 }
brorientation OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Paper Orientation.
1:portrait
2:landscape"
::= { prt-condition 2 }
brcopies OBJECT-TYPE
SYNTAX INTEGER (1..999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Copy Pages. 1-999 pages"
::= { prt-condition 4 }
brTBD3 OBJECT-TYPE
SYNTAX INTEGER (1..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { prt-condition 6 }
brresolution OBJECT-TYPE
SYNTAX INTEGER (0..1200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Resolution. 300, 600 or 1200dpi"
::= { prt-condition 8 }
brpageprotect OBJECT-TYPE
SYNTAX INTEGER (0..6)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Page Protect mode
1:Off
3:Auto
4:Letter
5:Legal
6:A4"
::= { prt-condition 10 }
brlines OBJECT-TYPE
SYNTAX INTEGER (5..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"lines per page. 5-128"
::= { prt-condition 11 }
brpaper OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
prc16k195x270(925),
a5l(923),
b6JIS(924),
prc16k184x260(926),
prc16k197x273(927),
auto(1001)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Paper size.
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM (ANY)
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
920:3x5(inches)
921:Envelopes Y4
922:Largest envelopes of the West
923:A5L
924:B6JIS
925:16K195x270
926:16K184x260
927:197x273
999:Other
1000:No Casette
1001:Auto"
::= { prt-condition 13 }
brpapertype OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Media type.
0:Regular
1:Thick paper
2:Thicker paper
3:Transparency
4:Thin paper
5:Bond paper
6:ENVELOPES
7:ENV. THICK
8:ENV. THIN
9:RECYCLED
10:HAGAKI
11:LABEL
1nd (default) Tray PaperType"
::= { prt-condition 22 }
brpapertype2 OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Media type.
0:Regular
1:Thick paper
2:Thicker paper
3:Transparency
4:Thin paper
5:Bond paper
6:ENVELOPES
7:ENV. THICK
8:ENV. THIN
9:RECYCLED
10:HAGAKI
11:LABEL
2nd Tray PaperType"
::= { prt-condition 23 }
brpapertypeMP OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Media type.
0:Regular
1:Thick paper
2:Thicker paper
3:Transparency
4:Thin paper
5:Bond paper
6:ENVELOPES
7:ENV. THICK
8:ENV. THIN
9:RECYCLED
10:HAGAKI
11:LABEL
1nd (default) Tray PaperType"
::= { prt-condition 26 }
brdensity OBJECT-TYPE
SYNTAX INTEGER (-15..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Density. -15..15"
::= { prt-density 5 }
brmanualfeed OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Manualfeed mode.
1:Off
2:On"
::= { manual 4 }
brmpsize OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"MP Tray paper size
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor"
::= { mp 1 }
brtray1size OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray1 paper size
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor"
::= { cassette 1 }
brtray2size OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray2 paper size
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor"
::= { cassette2 1 }
brtray3size OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray3 paper size
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor"
::= { cassette3 1 }
brtray4size OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray4 paper size
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor"
::= { cassette4 1 }
brret OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"HRC mode.
1:Off
2:Bright
3:Medium
4:Dark"
::= { economy 5 }
breconomode OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Toner Save mode.
100:Off
0:On"
::= { economy 7 }
brPrtGeneralEmulationTimeout OBJECT-TYPE
SYNTAX INTEGER (1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Emulation Timeout. 1- 99(sec)"
::= { general 1 }
brPrtGeneralFeeder OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Feeder mode.
0:Auto
1:MP Tray
2:Tray1
3:Tray2
4:Tray3
5:Tray4 "
::= { general 2 }
brPrtGeneralPowerSave OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Power Save mode.
1:Off
2:On"
::= { general 3 }
brPrtGeneralBuzzer OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Buzzer.
1:Off
2:On"
::= { general 4 }
brPrtGeneralColor OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Color mode
1:Monochrome
2:Color
3:Auto"
::= { general 5 }
brPrtGeneralDuplex OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Duplex mode
1:Off(Simplex)
2:On(Duplex)"
::= { general 6 }
brPrtGeneralBinding OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Binding type
3:Short Edge
2:Long Edge"
::= { general 7 }
brPrtAdvancedPriority OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"FX/XL Priority.
1:IBM XL
2:EPSON FX"
::= { advanced 1 }
brPrtAdvancedUseMPTrayFirst OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"MP Tray First
1:No
2:Yes"
::= { advanced 2 }
brPrtAdvancedMPTrayFeed OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"MP Tray feed mode.
1:Single
2:Continuous"
::= { advanced 3 }
brPrtAdvancedXOffset OBJECT-TYPE
SYNTAX INTEGER (-500..500)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"X Offset. -500 to +500 pixel(600dpi)"
::= { advanced 4 }
brPrtAdvancedYOffset OBJECT-TYPE
SYNTAX INTEGER (-500..500)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Y Offset. -500 to +500 pixel(600dpi)"
::= { advanced 5 }
brPrtAdvancedImageCompression OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Image Compression mode.
0:Auto
1:Off
2:On"
::= { advanced 6 }
brPrtAdvancedAutoFormFeed OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Auto Formfeed mode.
1:Off
2:On"
::= { autoff 1 }
brPrtAdvancedAutoTimeout OBJECT-TYPE
SYNTAX INTEGER (1..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Auto Formfeed timeout. 1-99 (sec)"
::= { autoff 2 }
brPrtAdvancedFFSuppress OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"FF Suppress mode.
1:Off
2:On"
::= { advanced 8 }
brPrtAdvancedTonerLowPrint OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print mode on Toner Low.
1:Stop
2:Continue"
::= { advanced 9 }
brPrtAdvancedPrintDensity OBJECT-TYPE
SYNTAX INTEGER (0..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Density. 1-15"
::= { advanced 10 }
brPrtAdvancedInputBuffer OBJECT-TYPE
SYNTAX INTEGER (1..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Input Buffer size. 1-15 blocks"
::= { advanced 11 }
brPrtAdvancedLanguage OBJECT-TYPE
SYNTAX INTEGER {
english(1),
danish(2),
dutch(3),
finish(4),
french(5),
german(6),
italian(7),
norwegian(8),
portuguse(9),
swedish(10),
spanish(11),
turkish(12),
polish(13),
japanese(14),
russian(15),
czech(16),
hungarian(17),
romanian(18),
bulgarian(19),
slovakian(20),
chinese(21),
brazil(22)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"1:ENGLISH
2:DANISH
3:DUTCH
4:FINNISH
5:FRENCH
6:GERMAN
7:ITALIAN
8:NORWEGIAN
9:PORTUGUESE
10:SWEDISH
11:SPANISH
12:TURKISH
13:POLISH
14:JAPANESE
15:RUSSIAN
16:CZECH
17:HUNGARIAN
18:ROMANIAN
19:BULGARIAN
20:SLOVAKIAN
21:CHINESE
22:BRAZIL"
::= { advanced 12 }
brSecurePrintRAMSizeMax OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Max of Secure print RAM Size"
::= { advanced 13 }
brSecurePrintRAMSize OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secure print RAM Size"
::= { advanced 14 }
brPrtAdvancedJamRecovery OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Jam recovery setting"
::= { advanced 15 }
brPrtAdvancedSleepIndication OBJECT-TYPE
SYNTAX INTEGER {
off(1),
dimmed(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"By enabling the Dimmed option, the status LED is dimmed while the printer is in sleep mode."
::= { advanced 16 }
brPrtAdvancedDestination OBJECT-TYPE
SYNTAX INTEGER {
standardOutputTray(1),
oct(2),
octStack(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Destination"
::= { advanced 17 }
brPrtAdvancedLowerLCD OBJECT-TYPE
SYNTAX INTEGER {
nonePage(1),
counter(2),
jobName(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lower LCD"
::= { advanced 18 }
brPrtAdvancedAutoOnline OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Auto Online"
::= { advanced 19 }
brPrtAdvancedButtonRepeat OBJECT-TYPE
SYNTAX INTEGER (1..20)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Button Repeat. 0.1-2.0"
::= { advanced 20 }
brPrtAdvancedMessageScroll OBJECT-TYPE
SYNTAX INTEGER (1..20)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Message Scroll. 1-10"
::= { advanced 21 }
brPrtAdvancedLCDDensity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LCDDensity"
::= { advanced 23 }
brPrtAdvancedErrorBuzzer OBJECT-TYPE
SYNTAX INTEGER {
off(1),
normal(2),
special(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Error Buzzer"
::= { buzzer 1 }
brPrtAdvancedPanelBuzzer OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Panel Buzzer"
::= { buzzer 2 }
brPrtAdvancedBuzzerVolume OBJECT-TYPE
SYNTAX INTEGER {
high(1),
low(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Buzzer Volume"
::= { buzzer 3 }
brSmallPaperSizeMP OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
noCasette(1000)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"MP Tray Small Paper size.
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
1000:No Casette"
::= { smallPaperSize 1 }
brSmallPaperSize1 OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
noCasette(1000)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray1 Small Paper size.
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
1000:No Casette"
::= { smallPaperSize 2 }
brSmallPaperSize2 OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
noCasette(1000)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray2 Small Paper size.
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
1000:No Casette"
::= { smallPaperSize 3 }
brSmallPaperSize3 OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
noCasette(1000)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray3 Small Paper size.
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
1000:No Casette"
::= { smallPaperSize 4 }
brSmallPaperSize4 OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
noCasette(1000)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Tray4 Small Paper size.
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
1000:No Casette"
::= { smallPaperSize 5 }
brPrtAdvancedTrayPriority OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The value of brTrayPriorityIndex corresponding to the default setting."
::= { trayPriority 1 }
brTrayPriorityCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of TrayPriority INDEX."
::= { trayPriority 2 }
brTrayPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrTrayPriorityEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents TrayPriority setting."
::= { trayPriority 3 }
brTrayPriorityEntry OBJECT-TYPE
SYNTAX BrTrayPriorityEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the TrayPriority table. Rows cannot be created or deleted."
INDEX { brTrayPriorityIndex }
::= { brTrayPriorityTable 1 }
BrTrayPriorityEntry ::=
SEQUENCE {
brTrayPriorityIndex
INTEGER,
brTrayPriorityMember
OCTET STRING
}
brTrayPriorityIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brTrayPriorityEntry 1 }
brTrayPriorityMember OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The TrayPriority member data.
Format:
valulen(1byte), value(valulen byte)"
::= { brTrayPriorityEntry 2 }
brCarbonCopyMode OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2),
auto(3),
parallel(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Carbon Copy mode setting."
::= { carbonCopy 1 }
brCarbonCopies OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The copies setting of Carbon Copy function."
::= { carbonCopy 2 }
brCarbonCopyTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCarbonCopyEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents CarbonCopy setting."
::= { carbonCopy 10 }
brCarbonCopyEntry OBJECT-TYPE
SYNTAX BrCarbonCopyEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the CarbonCopy table. Rows cannot be created or deleted."
INDEX { brCarbonCopyIndex }
::= { brCarbonCopyTable 1 }
BrCarbonCopyEntry ::=
SEQUENCE {
brCarbonCopyIndex
INTEGER,
brCarbonCopyTray
INTEGER,
brCarbonCopyMacro
INTEGER,
brCarbonCopyMacroID
INTEGER
}
brCarbonCopyIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brCarbonCopyEntry 1 }
brCarbonCopyTray OBJECT-TYPE
SYNTAX INTEGER {
tray1(1),
tray2(2),
tray3(3),
tray4(4),
mpTray(10),
auto(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Copy Tray setting."
::= { brCarbonCopyEntry 2 }
brCarbonCopyMacro OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Carbon Copy Macro Setting"
::= { brCarbonCopyEntry 3 }
brCarbonCopyMacroID OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Carbon Copy Macro ID Setting"
::= { brCarbonCopyEntry 4 }
brMediaFixTray1 OBJECT-TYPE
SYNTAX INTEGER {
off(1),
regular(2),
thick(3),
thicker(4),
transparency(5),
thin(6),
bond(7),
envelopes(8),
envThick(9),
envThin(10),
recycled(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Media Fix setting for tray1."
::= { mediaFix 1 }
brMediaFixTray2 OBJECT-TYPE
SYNTAX INTEGER {
off(1),
regular(2),
thick(3),
thicker(4),
transparency(5),
thin(6),
bond(7),
envelopes(8),
envThick(9),
envThin(10),
recycled(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Media Fix setting for tray2."
::= { mediaFix 2 }
brMediaFixTray3 OBJECT-TYPE
SYNTAX INTEGER {
off(1),
regular(2),
thick(3),
thicker(4),
transparency(5),
thin(6),
bond(7),
envelopes(8),
envThick(9),
envThin(10),
recycled(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Media Fix setting for tray3."
::= { mediaFix 3 }
brMediaFixTray4 OBJECT-TYPE
SYNTAX INTEGER {
off(1),
regular(2),
thick(3),
thicker(4),
transparency(5),
thin(6),
bond(7),
envelopes(8),
envThick(9),
envThin(10),
recycled(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Media Fix setting for tray4."
::= { mediaFix 4 }
brMediaFixMP OBJECT-TYPE
SYNTAX INTEGER {
off(1),
regular(2),
thick(3),
thicker(4),
transparency(5),
thin(6),
bond(7),
envelopes(8),
envThick(9),
envThin(10),
recycled(11)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Media Fix setting for MPtray."
::= { mediaFix 10 }
brDirectPrintPaperSize OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
a5l(923),
b6jis(924),
prc16k195x270(925),
prc16k184x260(926),
prc16k197x273(927)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Paper size.
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM (ANY)
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
920:3x5(inches)
921:Envelopes Y4
922:Largest envelopes of the West
923:A5L
924:B6JIS
925:16K195x270
926:16k184x260
927:16k197x273"
::= { directprint 1 }
brDirectPrintMediaType OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Media type.
0:Regular
1:Thick paper
2:Thicker paper
3:Transparency
4:Thin paper
5:Bond paper
6:ENVELOPES
7:ENV. THICK
8:ENV. THIN
9:RECYCLED
10:HAGAKI
11:LABEL
1nd (default) Tray PaperType"
::= { directprint 2 }
brDirectPrintMultipulPage OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 3 }
brDirectPrintOrientation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 4 }
brDirectPrintCollate OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 5 }
brDirectPrintOutputColor OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 6 }
brDirectPrintPrintQuality OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 7 }
brDirectPrintPdfOption OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { directprint 8 }
brDirectPrintSetting OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { directprint 9 }
brDirectPrintPdfThumbnailType OBJECT-TYPE
SYNTAX INTEGER {
alternativeImage(1),
reductionImage(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PDF Thumbnail Type
1:AlternativeImage
2:ReductionImage"
::= { directprint 10 }
brPictBridgePaperSize OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default Paper size.
-1:No Casette
1:Executive
2:Letter
3:Legal
24:A6
25:A5
26:A4
27:A3(ISO)
45:B5(JIS)
46:B4(JIS)
80:Monarch
81:COM10
90:DL
91:C5
99:B6
100:B5
890:LEDGER
891:A3PLUS(13x19)
892:Letter Short Edge
893:A4 Short Edge
894:A4LONG
895:Executive Short Edge
896:B5(ISO) Short Edge
897:CUSTOM (ANY)
898:A4/Letter
899:B5/Executive
900:Envelopes
901:DL-L
902:HAGAKI
903:FOLIO
904:ORGANIZER J
905:ORGANIZER K
906:ORGANIZER L
907:ORGANIZER M
908:USER DEFINED
911:Detect Sensor
920:3x5(inches)
921:Envelopes Y4
922:Largest envelopes of the West"
::= { pictbridge 1 }
brPictBridgeOrientation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { pictbridge 2 }
brPictBridgeDateTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { pictbridge 3 }
brPictBridgeFileName OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { pictbridge 4 }
brPictBridgePrintQuality OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { pictbridge 5 }
brPictBridgePrintSetting OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { pictbridge 6 }
brColorCalibration OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 1 }
brColorCalibrationReset OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 2 }
brAutoRegistRegistrate OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 3 }
brAutoRegistSetInterval OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 4 }
brRegistrationPrintChart OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 5 }
brRegistrationXMagentaLeft OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 6 }
brRegistrationXMagentaRight OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 7 }
brRegistrationXCyanLeft OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 8 }
brRegistrationXCyanRight OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 9 }
brRegistrationXYellowLeft OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 10 }
brRegistrationXYellowRight OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 11 }
brRegistrationYMagenta OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 12 }
brRegistrationYCyan OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 13 }
brRegistrationYYellow OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { colorcorrection 14 }
brPrtMailbox OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Mailbox Installed of not"
::= { mail 1 }
brPrtMailboxOutbin OBJECT-TYPE
SYNTAX INTEGER (0..110)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Outbin"
::= { mail 4 }
brPrtMailboxProtectGroup OBJECT-TYPE
SYNTAX INTEGER (0..99)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Mailbox Protect"
::= { mail 5 }
brPrtAvoidMailboxFullGroup OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Avoid Mailbox Full"
::= { mail 6 }
brPrtMailboxProtectTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrtMailboxProtectEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"unused"
::= { mail 2 }
brPrtMailboxProtectEntry OBJECT-TYPE
SYNTAX BrPrtMailboxProtectEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"unused"
INDEX { brPrtMailboxProtectIndex }
::= { brPrtMailboxProtectTable 1 }
BrPrtMailboxProtectEntry ::=
SEQUENCE {
brPrtMailboxProtectIndex
INTEGER,
brPrtMailboxProtect
INTEGER
}
brPrtMailboxProtectIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { brPrtMailboxProtectEntry 1 }
brPrtMailboxProtect OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { brPrtMailboxProtectEntry 2 }
brPrtAvoidMailboxFullTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrtAvoidMailboxFullEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"unused"
::= { mail 3 }
brPrtAvoidMailboxFullEntry OBJECT-TYPE
SYNTAX BrPrtAvoidMailboxFullEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"unused"
INDEX { brPrtAvoidMailboxFullIndex }
::= { brPrtAvoidMailboxFullTable 1 }
BrPrtAvoidMailboxFullEntry ::=
SEQUENCE {
brPrtAvoidMailboxFullIndex
INTEGER,
brPrtAvoidMailboxFull
INTEGER
}
brPrtAvoidMailboxFullIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { brPrtAvoidMailboxFullEntry 1 }
brPrtAvoidMailboxFull OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { brPrtAvoidMailboxFullEntry 2 }
brPrtFinisher OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Finisher type
0:no finisher
1:FS5050
2:FS5100"
::= { finisher 1 }
brPrtCatchTray OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"catch tray Installed or not"
::= { catch-tray 1 }
brPagePCLLeftMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL LeftMargin
1270N :0-145
2400Ce :0-176"
::= { margin-p 1 }
brPagePCLRightMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL RightMargin
1270N :10-155
2400Ce :10-186"
::= { margin-p 2 }
brPagePCLTopMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL TopMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-p 3 }
brPagePCLBottomMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL BottomMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-p 4 }
brPagePCLLines OBJECT-TYPE
SYNTAX INTEGER (5..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL Form Line 5-128"
::= { margin-p 5 }
brPagePCLAutoLF OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL AutoLF
1:Off
2:On"
::= { auto-p 1 }
brPagePCLAutoCR OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL AutoCR
1:Off
2:On"
::= { auto-p 2 }
brPagePCLAutoWrap OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL AutoWrap
1:Off
2:On"
::= { auto-p 3 }
brPagePCLAutoSkip OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PCL AutoSkip
1:Off
2:On"
::= { auto-p 4 }
brPagePSPrintPSError OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PrintPSError
1:Off
2:On"
::= { ps 1 }
brPagePSKeepPCLFonts OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"KeepPCLFonts
1:Off
2:On"
::= { ps 2 }
brPagePSCAPTsetting OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PS CAPT setting
1:Off
2:On"
::= { ps 3 }
brPageGLPen1Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen1 1 }
brPageGLPen1GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GLPen GrayLevel
0:15%
1:30%
2:45%
3:75%
4:90%
5:100%"
::= { pen1 2 }
brPageGLPen2Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen2 1 }
brPageGLPen2GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GLPen GrayLevel
0:15%
1:30%
2:45%
3:75%
4:90%
5:100%"
::= { pen2 2 }
brPageGLPen3Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen3 1 }
brPageGLPen3GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GLPen GrayLevel
0:15%
1:30%
2:45%
3:75%
4:90%
5:100%"
::= { pen3 2 }
brPageGLPen4Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen4 1 }
brPageGLPen4GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GLPen GrayLevel
0:15%
1:30%
2:45%
3:75%
4:90%
5:100%"
::= { pen4 2 }
brPageGLPen5Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen5 1 }
brPageGLPen5GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { pen5 2 }
brPageGLPen6Size OBJECT-TYPE
SYNTAX INTEGER (0..16)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GL PenSize 1-16"
::= { pen6 1 }
brPageGLPen6GrayLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"GLPen GrayLevel
0:15%
1:30%
2:45%
3:75%
4:90%
5:100%"
::= { pen6 2 }
brPageEPSONLeftMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON LeftMargin
1270N :0-145
2400Ce :0-176"
::= { margin-e 1 }
brPageEPSONRightMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON RightMargin
1270N :10-155
2400Ce :10-186"
::= { margin-e 2 }
brPageEPSONTopMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON TopMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-e 3 }
brPageEPSONBottomMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON BottomMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-e 4 }
brPageEPSONLines OBJECT-TYPE
SYNTAX INTEGER (5..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON Form Line 5-128"
::= { margin-e 5 }
brPageEPSONAutoLF OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON AutoLF
1:Off
2:On"
::= { auto-e 1 }
brPageEPSONAutoMask OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"EPSON AutoMask
1:Off
2:On"
::= { auto-e 5 }
brPageIBMLeftMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM LeftMargin
1270N :0-145
2400Ce :0-176"
::= { margin-i 1 }
brPageIBMRightMargin OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM LeftMargin
1270N :10-155
2400Ce :10-186"
::= { margin-i 2 }
brPageIBMTopMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM BottomMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-i 3 }
brPageIBMBottomMargin OBJECT-TYPE
SYNTAX INTEGER (0..200)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM BottomMargin
0:0
33:0.33
50:0.5
100:1.0
150:1.5
200:2.0"
::= { margin-i 4 }
brPageIBMLines OBJECT-TYPE
SYNTAX INTEGER (5..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM Form Line 5-128"
::= { margin-i 5 }
brPageIBMAutoLF OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM AutoLF
1:Off
2:On"
::= { auto-i 1 }
brPageIBMAutoCR OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM AutoCR
1:Off
2:On"
::= { auto-i 2 }
brPageIBMAutoMask OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IBM AutoMask
1:Off
2:On"
::= { auto-i 5 }
brFontName OBJECT-TYPE
SYNTAX INTEGER (0..99999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { fontsetup 1 }
brFontPointSize OBJECT-TYPE
SYNTAX INTEGER (4..99999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused(400-99975)"
::= { fontsetup 2 }
brFontPitch OBJECT-TYPE
SYNTAX INTEGER (0..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused(44-9999)"
::= { fontsetup 3 }
brFontSymbolSet OBJECT-TYPE
SYNTAX INTEGER (0..99999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { fontsetup 4 }
brPanelResetUser OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"User Reset"
::= { reset 1 }
brPanelResetFactory OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Factory Reset"
::= { reset 2 }
brPanelTestConfiguration OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Config page"
::= { test 1 }
brPanelTestFontList OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Fonts list"
::= { test 2 }
brPanelTestTestPage OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Test page"
::= { test 3 }
brPanelTestDemoPage OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print Demo page
0:Enable Print Demo page
1:Disable Print Demo page"
::= { test 4 }
brPanelLockPasswd OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { panellock 1 }
brPanelLock OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The state of panel lock"
::= { panellock 2 }
brPanelLockOn OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Panel Lock by setting a password."
::= { panellock 3 }
brPanelLockOff OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Panel Lock is canceled by inputting a password.."
::= { panellock 4 }
brPanelKeyOnline OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press Online Key"
::= { key 1 }
brPanelKeyFormFeed OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press FormFeed Key"
::= { key 2 }
brPanelKeyContinue OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press Countinue Key"
::= { key 3 }
brPanelKeyMode OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { key 4 }
brPanelKeyGo OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press Go Key"
::= { key 5 }
brPanelKeyJobCancel OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press JobCancel Key"
::= { key 6 }
brPanelKeyReprint OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press Reprint Key"
::= { key 7 }
brPanelKeySecure OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Press SecurePrint Key"
::= { key 8 }
brLCDMode1 OBJECT-TYPE
SYNTAX INTEGER {
fix(1),
blink(2),
scroll(3),
blinkScroll(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
1:fix
2:blink
3:scroll"
::= { panelinfo 1 }
brLCDString1 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of first line."
::= { panelinfo 2 }
brLCDMode2 OBJECT-TYPE
SYNTAX INTEGER {
fix(1),
blink(2),
scroll(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
1:fix
2:blink
3:scroll"
::= { panelinfo 3 }
brLCDString2 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of second line."
::= { panelinfo 4 }
brLCDString16fix OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of 16fix."
::= { panelinfo 5 }
brBackLightColor OBJECT-TYPE
SYNTAX INTEGER {
green(1),
orange(2),
red(3),
notsupport(255)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
0:Off
1:Green
2:Orange
3:Red"
::= { panelinfo 6 }
brLCDMode3 OBJECT-TYPE
SYNTAX INTEGER {
fix(1),
blink(2),
scroll(3),
blinkScroll(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
1:fix
2:blink
3:scroll"
::= { panelinfo 7 }
brLCDString3 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of first line."
::= { panelinfo 8 }
brLCDMode4 OBJECT-TYPE
SYNTAX INTEGER {
fix(1),
blink(2),
scroll(3),
blinkScroll(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
1:fix
2:blink
3:scroll"
::= { panelinfo 9 }
brLCDString4 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of first line."
::= { panelinfo 10 }
brLCDMode5 OBJECT-TYPE
SYNTAX INTEGER {
fix(1),
blink(2),
scroll(3),
blinkScroll(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display Mode.
1:fix
2:blink
3:scroll"
::= { panelinfo 11 }
brLCDString5 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LCD Display String of first line."
::= { panelinfo 12 }
brLCDContrast OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value adjusts the contrast of the LCD Display."
::= { panelinfo 13 }
brInfoSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Serial number of printer"
::= { printerinfomation 1 }
brInfoType OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused"
::= { printerinfomation 2 }
brInfoUpperMIBVer OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused (upper digit of the MIB version)"
::= { version 1 }
brInfoLowerMIBVer OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused (lower digit of the MIB version)"
::= { version 2 }
brInfoStatus OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Status message ID"
::= { printerinfomation 4 }
brInfoNetVerUpStatus OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused"
::= { printerinfomation 5 }
brInfoPrinterUStatus OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Status ID"
::= { printerinfomation 6 }
brInfoPConSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"BRPCon support
0:not supported
1:supported"
::= { printerinfomation 7 }
brInfoMaintenance OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maintenance info."
::= { printerinfomation 8 }
brInfoModelNumber OBJECT-TYPE
SYNTAX INTEGER {
hl2400ce(4),
hl3400CN(5),
hl3260(6),
hl2460(8),
hl2600cn(9),
hl3450cn(11),
am(13),
zlhe(14),
zl2(15),
jigen(16),
aml(17),
l4c(18),
all(19),
alLedModel(20),
alLcdModel(21),
hl4040(22),
allchn(23),
hl4050hl4070(24),
all2(25),
zlfb(101),
zl(102),
bh(103),
bhfb(104),
zlhs(105),
bhhs(106),
zl2fb(107),
bhl2mfc(108),
bhl2fb(109),
zl2mfc(110),
mini2(111),
mini2adf(112),
bh3fb(113),
bh3mfc(114),
allmfc(115),
allfb(116),
slow4c(117),
mini2eColorLCD(118),
mini2eColorLCDADF(119),
alfb(120),
dcp540(121),
dcp750(122),
mfc440(123),
mfc665(124),
mfc850(125),
mfc860(126),
mfc5460(127),
mfc5860(128),
dcp6150(129),
dcp6260(130),
dcp6460(131),
dcp6860(132),
dcp770(133),
mfc480(134),
acfbCIS(135),
acfbCCD(136),
mfc7440(137),
mfc7840(138),
mfc5490(139),
mfc5890(140),
mfc6490(141),
dcp6690(142),
mfc6890(143),
dcp585(144),
mfc490(145),
mfc790(146),
mfc990(147),
mfc930(148)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Printer Model ID
4:2400Ce
5:3400CN
6:3260
8:2460
9:2600cn
11:3450cn
13:am
14:zlhe
15:zl2
16:jigen
17:aml
18:l4c
19: ALL
20: AL LED
21: AL LCD
22: HL-4040CN
23: ALL China
24: HL-4050CDN/HL-4070CDW
25: ALL2
101:ZL MFC FB type
102:ZL MFC Normal type
103:BH MFC Nornal type
104:BH MFC FB type
105:ZL MFC with HS
106:BH MFC with HS
107: ZL2FB
108: BHL2MFC
109: BHL2FB
110: ZL2MFC
111: Mini2
112: Mini2 ADF
113: BH3FB
114: BH3MFC
115: ALL-MFC
116: ALL-FB
117: SLow4C
118: mini2eColorLCD,
119: mini2eColorLCD ADF
120: AL-FB
121: DCP540
122: DCP750
123: MFC440
124: MFC665
125: MFC850
126: MFC860
127: MFC5460
128: MFC5860
129: DCP6150
130: DCP6260
131: MFC6460
132: MFC6860
133: DCP770
134: MFC480
135: AC-FB CIS
136: AC-FB CCD
137: MFC7440
138: MFC7840
139: MFC5490
140: MFC5890
141: MFC6490
142: DCP6690
143: MFC6890
144: DCP585
145: MFC490
146: MFC790
147: MFC990
148: MFC930"
::= { printerinfomation 9 }
brInfoCounter OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Page counter"
::= { printerinfomation 10 }
brInfoNextCare OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Remaining life info."
::= { printerinfomation 11 }
brInfoHDDSlot1 OBJECT-TYPE
SYNTAX INTEGER (0..6)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Card Slot1 status
1:complete
2:IO error
3:memory error
4:not found
5:no device
6:no file(format)"
::= { printerinfomation 12 }
brInfoHDDSlot2 OBJECT-TYPE
SYNTAX INTEGER (0..6)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Card Slot2 status
1:complete
2:IO error
3:memory error
4:not found
5:no device
6:no file(format)"
::= { printerinfomation 13 }
brInfoHDDInternal OBJECT-TYPE
SYNTAX INTEGER (0..6)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Internal HDD info.
1:complete
2:IO error
3:memory error
4:not found
5:no device
6:no file(format)"
::= { printerinfomation 14 }
brInfoHDDSize OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"unused"
::= { printerinfomation 15 }
brInfoSolutionsCenterURL OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Brother Solutions Center's URL"
::= { printerinfomation 16 }
brInfoDeviceRomVersion OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The device rom version"
::= { printerinfomation 17 }
brInfoCoverage OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Coverage info."
::= { printerinfomation 18 }
brInfoEstimatedPagesRemaining OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Estimated pages remaining info."
::= { printerinfomation 19 }
brInfoReplaceCount OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Replace count info."
::= { printerinfomation 20 }
brInfoJamCount OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Jam count info."
::= { printerinfomation 21 }
brInfoJamCountClear OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Jam count Clear."
::= { printerinfomation 22 }
brInfoReplaceTime OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Replace count time info."
::= { printerinfomation 23 }
brInfoDeviceSubRomVersion OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PCL/PS ROM Version."
::= { printerinfomation 24 }
brErrorHistoryCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Error History."
::= { errorHistory 1 }
brErrorHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrErrorHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Error History."
::= { errorHistory 2 }
brErrorHistoryEntry OBJECT-TYPE
SYNTAX BrErrorHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the ErrorHistory table. Rows cannot be created or deleted."
INDEX { brErrorHistoryIndex }
::= { brErrorHistoryTable 1 }
BrErrorHistoryEntry ::=
SEQUENCE {
brErrorHistoryIndex
INTEGER,
brErrorHistoryDescription
OCTET STRING
}
brErrorHistoryIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the error history."
::= { brErrorHistoryEntry 1 }
brErrorHistoryDescription OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ErrorHistory Description."
::= { brErrorHistoryEntry 2 }
brErrorHistoryAllClear OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"All clear Error History."
::= { errorHistory 3 }
brCommunicationErrorHistoryCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Communication Error History."
::= { errorHistory 11 }
brCommunicationErrorHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCommunicationErrorHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Communication Error History."
::= { errorHistory 12 }
brCommunicationErrorHistoryEntry OBJECT-TYPE
SYNTAX BrCommunicationErrorHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the Communication ErrorHistory table. Rows cannot be created or deleted."
INDEX { brCommunicationErrorHistoryIndex }
::= { brCommunicationErrorHistoryTable 1 }
BrCommunicationErrorHistoryEntry ::=
SEQUENCE {
brCommunicationErrorHistoryIndex
INTEGER,
brCommunicationErrorHistoryDescription
OCTET STRING
}
brCommunicationErrorHistoryIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the Communication error history."
::= { brCommunicationErrorHistoryEntry 1 }
brCommunicationErrorHistoryDescription OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Communication Error History Description."
::= { brCommunicationErrorHistoryEntry 2 }
brPrintPagesTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrintPagesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Print Pages."
::= { printPages 1 }
brPrintPagesEntry OBJECT-TYPE
SYNTAX BrPrintPagesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PrintPages table. Rows cannot be created or deleted."
INDEX { brPrintPagesIndex }
::= { brPrintPagesTable 1 }
BrPrintPagesEntry ::=
SEQUENCE {
brPrintPagesIndex
INTEGER,
brPrintPagesPaperSize
INTEGER,
brPrintPages
Counter
}
brPrintPagesIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the print pages."
::= { brPrintPagesEntry 1 }
brPrintPagesPaperSize OBJECT-TYPE
SYNTAX INTEGER {
executive(1),
letter(2),
legal(3),
a6(24),
a5(25),
a4(26),
a3ISO(27),
b5JIS(45),
b4JIS(46),
monarch(80),
com10(81),
dl(90),
c5(91),
b6(99),
b5(100),
ledger(890),
a3PLUS(891),
letterShortEdge(892),
a4ShortEdge(893),
a4LONG(894),
executiveShortEdge(895),
b5ISOShortEdge(896),
custom(897),
a4Letter(898),
b5Executive(899),
envelopes(900),
dll(901),
hagaki(902),
folio(903),
organaizerJ(904),
organaizerK(905),
organaizerL(906),
organaizerM(907),
userdefined(908),
legalA4Long(909),
b6A5A6(910),
detectsensor(911),
inches3x5(920),
envelopesY4(921),
largestEnvelopesTheWest(922),
otherPage(999),
b6JIS(924)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The paper size of print pages."
::= { brPrintPagesEntry 2 }
brPrintPages OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of Print pages."
::= { brPrintPagesEntry 3 }
brPrintPagesMediaPlaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrintPagesMediaPlaceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Print Pages of Media Place."
::= { printPages 11 }
brPrintPagesMediaPlaceEntry OBJECT-TYPE
SYNTAX BrPrintPagesMediaPlaceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PrintPages Media Place table. Rows cannot be created or deleted."
INDEX { brPrintPagesMediaPlaceIndex }
::= { brPrintPagesMediaPlaceTable 1 }
BrPrintPagesMediaPlaceEntry ::=
SEQUENCE {
brPrintPagesMediaPlaceIndex
INTEGER,
brPrintPagesMediaPlaceType
INTEGER,
brPrintPagesMediaPlaceCounter
Counter
}
brPrintPagesMediaPlaceIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the print pages of media place."
::= { brPrintPagesMediaPlaceEntry 1 }
brPrintPagesMediaPlaceType OBJECT-TYPE
SYNTAX INTEGER {
face(1),
back(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The place of media."
::= { brPrintPagesMediaPlaceEntry 2 }
brPrintPagesMediaPlaceCounter OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of Print pages of media place."
::= { brPrintPagesMediaPlaceEntry 3 }
brPrintPagesFuncTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrintPagesFuncEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Print Pages of each function."
::= { printPages 21 }
brPrintPagesFuncEntry OBJECT-TYPE
SYNTAX BrPrintPagesFuncEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PrintPages Func table. Rows cannot be created or deleted."
INDEX { brPrintPagesFuncIndex }
::= { brPrintPagesFuncTable 1 }
BrPrintPagesFuncEntry ::=
SEQUENCE {
brPrintPagesFuncIndex
INTEGER,
brPrintPagesFuncType
INTEGER,
brPrintPagesFuncCounter
Counter
}
brPrintPagesFuncIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the print pages of each function."
::= { brPrintPagesFuncEntry 1 }
brPrintPagesFuncType OBJECT-TYPE
SYNTAX INTEGER {
pcPrinttotal(1),
faxtotal(2),
copytotal(3),
copycolor(4),
pcPrintcolor(5),
faxcolor(6),
pcPrintmono(7),
faxmono(8),
copymono(9)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The kind of function."
::= { brPrintPagesFuncEntry 2 }
brPrintPagesFuncCounter OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of Print pages of the function."
::= { brPrintPagesFuncEntry 3 }
brPrintPagesPaperTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPrintPagesPaperTypeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Print Pages of Paper Type."
::= { printPages 31 }
brPrintPagesPaperTypeEntry OBJECT-TYPE
SYNTAX BrPrintPagesPaperTypeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PrintPages Paper Type table. Rows cannot be created or deleted."
INDEX { brPrintPagesPaperTypeIndex }
::= { brPrintPagesPaperTypeTable 1 }
BrPrintPagesPaperTypeEntry ::=
SEQUENCE {
brPrintPagesPaperTypeIndex
INTEGER,
brPrintPagesPaperTypeType
INTEGER,
brPrintPagesPaperTypeCounter
Counter
}
brPrintPagesPaperTypeIndex OBJECT-TYPE
SYNTAX INTEGER (1..32767)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the print pages of paper type."
::= { brPrintPagesPaperTypeEntry 1 }
brPrintPagesPaperTypeType OBJECT-TYPE
SYNTAX INTEGER {
regularthinrecycled(12),
transparency(3),
thickthickerbond(13),
envelopesenvthickenvthin(14)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of paper."
::= { brPrintPagesPaperTypeEntry 2 }
brPrintPagesPaperTypeCounter OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The count of Print pages of paper type."
::= { brPrintPagesPaperTypeEntry 3 }
brCapabilityCopiesMax OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum value of copies"
::= { copies 1 }
brCapabilityCopiesMin OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The minimum value of copies"
::= { copies 2 }
brCapabilityOrientationCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of support of orientation"
::= { orientation 1 }
brCapabilityOrientationTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCapabilityOrientationEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents capability of orientation."
::= { orientation 2 }
brCapabilityOrientationEntry OBJECT-TYPE
SYNTAX BrCapabilityOrientationEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the capability of orientation table.
Rows cannot be created or deleted."
INDEX { brCapabilityOrientationIndex }
::= { brCapabilityOrientationTable 1 }
BrCapabilityOrientationEntry ::=
SEQUENCE {
brCapabilityOrientationIndex
INTEGER,
brCapabilityOrientationName
DisplayString
}
brCapabilityOrientationIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the capability of orientation."
::= { brCapabilityOrientationEntry 1 }
brCapabilityOrientationName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of orientation currently supported."
::= { brCapabilityOrientationEntry 2 }
brCapabilityPaperCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of kinds of the paper currently supported"
::= { paper 1 }
brCapabilityPaperTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCapabilityPaperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents capability of paper."
::= { paper 2 }
brCapabilityPaperEntry OBJECT-TYPE
SYNTAX BrCapabilityPaperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the capability of paper table.
Rows cannot be created or deleted."
INDEX { brCapabilityPaperIndex }
::= { brCapabilityPaperTable 1 }
BrCapabilityPaperEntry ::=
SEQUENCE {
brCapabilityPaperIndex
INTEGER,
brCapabilityPaperName
DisplayString
}
brCapabilityPaperIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the capability of paper."
::= { brCapabilityPaperEntry 1 }
brCapabilityPaperName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of paper currently supported."
::= { brCapabilityPaperEntry 2 }
brCapabilityMediatypeCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of kinds of the mediatype currently supported"
::= { mediatype 1 }
brCapabilityMediatypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCapabilityMediatypeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents capability of mediatype."
::= { mediatype 2 }
brCapabilityMediatypeEntry OBJECT-TYPE
SYNTAX BrCapabilityMediatypeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the capability of mediatype table.
Rows cannot be created or deleted."
INDEX { brCapabilityMediatypeIndex }
::= { brCapabilityMediatypeTable 1 }
BrCapabilityMediatypeEntry ::=
SEQUENCE {
brCapabilityMediatypeIndex
INTEGER,
brCapabilityMediatypeName
DisplayString
}
brCapabilityMediatypeIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the capability of mediatype."
::= { brCapabilityMediatypeEntry 1 }
brCapabilityMediatypeName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of mediatype currently supported."
::= { brCapabilityMediatypeEntry 2 }
brCapabilityResolutionCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of kinds of the resolution currently supported"
::= { resolution 1 }
brCapabilityResolutionTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrCapabilityResolutionEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents capability of resolution."
::= { resolution 2 }
brCapabilityResolutionEntry OBJECT-TYPE
SYNTAX BrCapabilityResolutionEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the capability of resolution table.
Rows cannot be created or deleted."
INDEX { brCapabilityResolutionIndex }
::= { brCapabilityResolutionTable 1 }
BrCapabilityResolutionEntry ::=
SEQUENCE {
brCapabilityResolutionIndex
INTEGER,
brCapabilityResolution
INTEGER
}
brCapabilityResolutionIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the capability of resolution."
::= { brCapabilityResolutionEntry 1 }
brCapabilityResolution OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of resolution currently supported."
::= { brCapabilityResolutionEntry 2 }
brPfKitIndexCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of PF kit."
::= { pfkit 1 }
brPfKitTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPfKitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PF kit."
::= { pfkit 2 }
brPfKitEntry OBJECT-TYPE
SYNTAX BrPfKitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PfKit table. Rows cannot be created or deleted."
INDEX { brPfKitIndex }
::= { brPfKitTable 1 }
BrPfKitEntry ::=
SEQUENCE {
brPfKitIndex
INTEGER,
brPfKitType
INTEGER,
brPfKitCount
Counter
}
brPfKitIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the PF kit."
::= { brPfKitEntry 1 }
brPfKitType OBJECT-TYPE
SYNTAX INTEGER {
pfkit1(1),
pfkit2(2),
pfkit3(3),
pfkit4(4),
pfkitmp(10),
pfkitdx(20)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PF kit ID."
::= { brPfKitEntry 2 }
brPfKitCount OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of the PF kit."
::= { brPfKitEntry 3 }
brScanCountIndexCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Scan place."
::= { scancount 1 }
brScanCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrScanCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents scan count."
::= { scancount 2 }
brScanCountEntry OBJECT-TYPE
SYNTAX BrScanCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the ScanCount table. Rows cannot be created or deleted."
INDEX { brScanCountIndex }
::= { brScanCountTable 1 }
BrScanCountEntry ::=
SEQUENCE {
brScanCountIndex
INTEGER,
brScanCountType
INTEGER,
brScanCountCounter
Counter
}
brScanCountIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value for the scan count place."
::= { brScanCountEntry 1 }
brScanCountType OBJECT-TYPE
SYNTAX INTEGER {
adf(1),
fb(2),
adfdx(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The scan place ID."
::= { brScanCountEntry 2 }
brScanCountCounter OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of the scan."
::= { brScanCountEntry 3 }
brStatusSleep OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Sleeping status
0:ready
1:sleep"
::= { printerstatus 1 }
brSecretMPRetry OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"unused"
::= { secret 1 }
brSecretReprint OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secret Reprint mode
0:Off
111:On
222:Job"
::= { secret 2 }
brFontSetting OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
" Font Setting
0:Brother Font
1:Agfa Font"
::= { secret 3 }
brFontSwitchOn OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
" Switch of Agfa Font On"
::= { secret 4 }
brFontSwitchOff OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Switch of Agfa Font Off"
::= { secret 5 }
brClockFuncTimeStyle OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Time format
0:YMD
1:MDY
2:DMY"
::= { clockfunction 1 }
brClockFuncSummerTime OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Summer time
1:Off
2:On"
::= { clockfunction 2 }
brClockFuncTimeZone OBJECT-TYPE
SYNTAX INTEGER (-24..24)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TimeZone"
::= { clockfunction 3 }
brClockFuncZoneSet OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TimeZone enable
1:Off
2:On"
::= { clockfunction 4 }
brFindPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { funa 1 }
brFindTime OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { funa 2 }
brAdminCapability OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"AdminCapability"
::= { adminCapa 1 }
brUserPasswordVerify OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Submit the print server's user password for verification.
An error will be returned if the password is incorrect."
::= { userSetting 1 }
brUserPassword OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Set the print server's user password value."
::= { userSetting 2 }
brpsVerifyPhysAddress OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..6) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"For verify physical address."
::= { verify 1 }
brBasicSettingConfigured OBJECT-TYPE
SYNTAX INTEGER {
unconfigured(1),
configured(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value indicates that the basic setting is configured or not.
The condition entry of this value is model dependent."
::= { npConfig 1 }
brLPDBannerPage OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LPR banner page
0: disabled.
1: enabled.
2: force to print."
::= { banner 1 }
brENetModeSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"ENet Mode
0:not supported
1:supported"
::= { eNet 1 }
brENetMode OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"ENet Mode
0:Auto
1:FD100B
2:100Base
3:FD10B
4:10BASE"
::= { eNet 2 }
brDNSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"DNS resolver
0:not supported
1:supported
This is the obsolete MIB that is not currently used."
::= { dns 1 }
brPrimaryDNSIP OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary DNS IP Address.
This is the obsolete MIB that is not currently used."
::= { dns 2 }
brSecondaryDNSIP OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary DNS IP Address
This is the obsolete MIB that is not currently used."
::= { dns 3 }
brDNSIPSetup OBJECT-TYPE
SYNTAX INTEGER {
static(1),
auto(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"DNS mode
1:static
2:auto"
::= { dns 4 }
brTCPIPConnectTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TCP/IP connect time."
::= { dns 5 }
brAdvancedDNSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"DNS resolver
0:not supported
1:supported"
::= { dns 6 }
brPrimaryDNSIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary DNS IP Address"
::= { dns 7 }
brSecondaryDNSIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary DNS IP Address"
::= { dns 8 }
brPOP3ServerName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The FQDN name of the POP3 server."
::= { dns 9 }
brSMTPServerName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The FQDN name of the SMTP server."
::= { dns 10 }
brPushStatusSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Notification
0:not supported
1:supported"
::= { pushstatus 1 }
brPriMailAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary Mail Address"
::= { priadmin 1 }
brPriError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary Error"
::= { priadmin 2 }
brSecMailAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary Mail Address"
::= { secadmin 1 }
brSecError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary Error"
::= { secadmin 2 }
brNotificationCount OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Notification Method."
::= { pushstatus 4 }
brNotificationTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrNotificationEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Notification Method."
::= { pushstatus 5 }
brNotificationEntry OBJECT-TYPE
SYNTAX BrNotificationEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the Notification table. Rows cannot be created or deleted."
INDEX { brNotificationIndex }
::= { brNotificationTable 1 }
BrNotificationEntry ::=
SEQUENCE {
brNotificationIndex
INTEGER,
brNotificationAddress
OCTET STRING,
brNotificationStatusGroup
INTEGER,
brNotificationShowURLInfo
INTEGER,
brNotificationErrorRule
OCTET STRING,
brNotificationRestoration
INTEGER
}
brNotificationIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brNotificationEntry 1 }
brNotificationAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Notification Address."
::= { brNotificationEntry 2 }
brNotificationStatusGroup OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Notification Status group"
::= { brNotificationEntry 3 }
brNotificationShowURLInfo OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of show URL infomation at Notification mail."
::= { brNotificationEntry 4 }
brNotificationErrorRule OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of sending requirements for Notification."
::= { brNotificationEntry 5 }
brNotificationRestoration OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of Restoration Notification mail"
::= { brNotificationEntry 6 }
brPrintersEmailaddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Printers Email Address."
::= { pushstatus 6 }
brNotificationVersion OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The version of Notification"
::= { pushstatus 7 }
brShowIPAddressInfo OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of show IP address infomation at Notification mail."
::= { pushstatus 8 }
brNotificationRuleTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrNotificationRuleEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Notification Method."
::= { pushstatus 50 }
brNotificationRuleEntry OBJECT-TYPE
SYNTAX BrNotificationRuleEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the Notification rule table. Rows cannot be created or deleted."
INDEX { brNotificationIndex, brNotificationRuleIndex }
::= { brNotificationRuleTable 1 }
BrNotificationRuleEntry ::=
SEQUENCE {
brNotificationRuleIndex
INTEGER,
brNotificationStatusID
INTEGER,
brNotificationMainRule
INTEGER,
brNotificationRuleValue
INTEGER
}
brNotificationRuleIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brNotificationRuleEntry 1 }
brNotificationStatusID OBJECT-TYPE
SYNTAX INTEGER {
coverOpen(1),
jam(2),
tonerLow(3),
tonerEmpty(4),
userConsumableWarning(5),
userConsumableError(6),
servicemanConsumableWarning(7),
servicemanConsumableError(8),
changeDrum(9),
memoryFull(10),
inputMediaError(11),
outputFull(12),
notInstalled(13),
machineError(14),
otherErrors(15)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Notification Status group ID"
::= { brNotificationRuleEntry 2 }
brNotificationMainRule OBJECT-TYPE
SYNTAX INTEGER {
off(1),
everytime(2),
times(3),
minutes(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The main rule of Notification setting."
::= { brNotificationRuleEntry 3 }
brNotificationRuleValue OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The value of Notification setting."
::= { brNotificationRuleEntry 4 }
brPJLInfoOptionsTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoOptionsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoOptions."
::= { pjlinfo 1 }
brPJLInfoOptionsEntry OBJECT-TYPE
SYNTAX BrPJLInfoOptionsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoOptions table. Rows cannot be created or deleted."
INDEX { brPJLInfoOptionsIndex }
::= { brPJLInfoOptionsTable 1 }
BrPJLInfoOptionsEntry ::=
SEQUENCE {
brPJLInfoOptionsIndex
INTEGER,
brPJLInfoOptions
OCTET STRING
}
brPJLInfoOptionsIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoOptionsEntry 1 }
brPJLInfoOptions OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoOptions."
::= { brPJLInfoOptionsEntry 2 }
brPJLInfoIntrayconfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoIntrayconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoIntrayconfig."
::= { pjlinfo 2 }
brPJLInfoIntrayconfigEntry OBJECT-TYPE
SYNTAX BrPJLInfoIntrayconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoIntrayconfig table. Rows cannot be created or deleted."
INDEX { brPJLInfoIntrayconfigIndex }
::= { brPJLInfoIntrayconfigTable 1 }
BrPJLInfoIntrayconfigEntry ::=
SEQUENCE {
brPJLInfoIntrayconfigIndex
INTEGER,
brPJLInfoIntrayconfig
OCTET STRING
}
brPJLInfoIntrayconfigIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoIntrayconfigEntry 1 }
brPJLInfoIntrayconfig OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoIntrayconfig."
::= { brPJLInfoIntrayconfigEntry 2 }
brPJLInfoOuttrayconfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoOuttrayconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoOuttrayconfig."
::= { pjlinfo 3 }
brPJLInfoOuttrayconfigEntry OBJECT-TYPE
SYNTAX BrPJLInfoOuttrayconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoOuttrayconfig table. Rows cannot be created or deleted."
INDEX { brPJLInfoOuttrayconfigIndex }
::= { brPJLInfoOuttrayconfigTable 1 }
BrPJLInfoOuttrayconfigEntry ::=
SEQUENCE {
brPJLInfoOuttrayconfigIndex
INTEGER,
brPJLInfoOuttrayconfig
OCTET STRING
}
brPJLInfoOuttrayconfigIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoOuttrayconfigEntry 1 }
brPJLInfoOuttrayconfig OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoOuttrayconfig."
::= { brPJLInfoOuttrayconfigEntry 2 }
brPJLInfoDXconfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoDXconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoDXconfig."
::= { pjlinfo 4 }
brPJLInfoDXconfigEntry OBJECT-TYPE
SYNTAX BrPJLInfoDXconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoDXconfig table. Rows cannot be created or deleted."
INDEX { brPJLInfoDXconfigIndex }
::= { brPJLInfoDXconfigTable 1 }
BrPJLInfoDXconfigEntry ::=
SEQUENCE {
brPJLInfoDXconfigIndex
INTEGER,
brPJLInfoDXconfig
OCTET STRING
}
brPJLInfoDXconfigIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoDXconfigEntry 1 }
brPJLInfoDXconfig OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoDXconfig."
::= { brPJLInfoDXconfigEntry 2 }
brPJLInfoStorageconfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoStorageconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoStorageconfig."
::= { pjlinfo 5 }
brPJLInfoStorageconfigEntry OBJECT-TYPE
SYNTAX BrPJLInfoStorageconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoStorageconfig table. Rows cannot be created or deleted."
INDEX { brPJLInfoStorageconfigIndex }
::= { brPJLInfoStorageconfigTable 1 }
BrPJLInfoStorageconfigEntry ::=
SEQUENCE {
brPJLInfoStorageconfigIndex
INTEGER,
brPJLInfoStorageconfig
OCTET STRING
}
brPJLInfoStorageconfigIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoStorageconfigEntry 1 }
brPJLInfoStorageconfig OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoStorageconfig."
::= { brPJLInfoStorageconfigEntry 2 }
brEmailReportsSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"E-mail reports
0:not supported
1:supported"
::= { eMailReports 1 }
brEmailReportsCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Administrator for E-mail reports."
::= { eMailReports 2 }
brEmailReportsTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrEmailReportsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents E-mail reports."
::= { eMailReports 11 }
brEmailReportsEntry OBJECT-TYPE
SYNTAX BrEmailReportsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the BrEmailReportsEntry table. Rows cannot be created or deleted."
INDEX { brEmailReportsIndex }
::= { brEmailReportsTable 1 }
BrEmailReportsEntry ::=
SEQUENCE {
brEmailReportsIndex
INTEGER,
brEmailReportsAddress
OCTET STRING,
brEmailReportsFrequency
INTEGER,
brEmailReportsTime
OCTET STRING,
brEmailReportsWeek
INTEGER,
brEmailReportsDate
INTEGER,
brEmailReportsSendReportNow
INTEGER,
brEmailReportsSendReportatPowerOn
INTEGER,
brEmailReportsNoRTCFrequency
INTEGER,
brEmailReportsReportFormat
INTEGER
}
brEmailReportsIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brEmailReportsEntry 1 }
brEmailReportsAddress OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..60) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The E-mail address of Administrator for E-mail reports."
::= { brEmailReportsEntry 2 }
brEmailReportsFrequency OBJECT-TYPE
SYNTAX INTEGER {
daily(1),
weekly(2),
monthly(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The frequency of sending E-mail reports."
::= { brEmailReportsEntry 3 }
brEmailReportsTime OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The time setting for E-mail reports."
::= { brEmailReportsEntry 4 }
brEmailReportsWeek OBJECT-TYPE
SYNTAX INTEGER {
sunday(1),
monday(2),
tuesday(3),
wednesday(4),
thursday(5),
friday(6),
saturday(7)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of day of the week for E-mail reports."
::= { brEmailReportsEntry 5 }
brEmailReportsDate OBJECT-TYPE
SYNTAX INTEGER (1..31)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of day for E-mail reports when real time clock exists."
::= { brEmailReportsEntry 6 }
brEmailReportsSendReportNow OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of Send Report Now function for E-mail reports."
::= { brEmailReportsEntry 7 }
brEmailReportsSendReportatPowerOn OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of Send Report at PowerOn for E-mail reports."
::= { brEmailReportsEntry 8 }
brEmailReportsNoRTCFrequency OBJECT-TYPE
SYNTAX INTEGER (1..30)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of day for E-mail reports when real time clock does not exists."
::= { brEmailReportsEntry 9 }
brEmailReportsReportFormat OBJECT-TYPE
SYNTAX INTEGER {
plaintext(1),
xml(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The setting of ReportFormat for E-mail reports."
::= { brEmailReportsEntry 10 }
brpsNodeName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The node name of this print server."
::= { brconfig 1 }
brpsSerialNumber OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The serial number of this print server."
::= { brconfig 2 }
brpsHardwareType OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Hardware type of the print server."
::= { brconfig 3 }
brpsMainRevision OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..5) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Revision level of the Print Server firmware suitable
for display. This object may be read but not written."
::= { brconfig 4 }
brpsBootRevision OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..5) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Revision level of the boot firmware (if applicable) suitable
for display. This object may be read but not written."
::= { brconfig 5 }
brpsPasswordVerify OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Submit the print server's password for verification. An error
will be returned if the password is incorrect."
::= { brconfig 6 }
brpsPassword OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Set the print server's password value."
::= { brconfig 7 }
brpsMIBVersion OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..5) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Revision level of the private MIB implemented by the device.
For example:
1.0
This object may be read but not written."
::= { brconfig 8 }
brpsOEMString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(3) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"OEM string setting for the print server.
This object may be read but not written."
::= { brconfig 9 }
brpsMIBMajor OBJECT-TYPE
SYNTAX INTEGER (0..9)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"MIB major version number."
::= { brconfig 10 }
brpsMIBMinor OBJECT-TYPE
SYNTAX INTEGER (0..99)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"MIB minor version number."
::= { brconfig 11 }
brSupportedInfo OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brconfig 200 }
brpsServerDescription OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Product name of print server.
For example: NC-3100h
This object may be read but not written."
::= { brconfig 12 }
brpsEnetMode OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Ethernet type."
::= { brconfig 13 }
brpsFlashROMSize OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Flash ROM Size of print server (MBytes)."
::= { brconfig 14 }
brpsSNMPGetCommunity OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SNMP Get Community Name."
::= { brconfig 15 }
brpsSNMPJetAdmin OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the JetAdmin compatibility mode is not enabled.
1 indicates JetAdmin compatibility mode is enabled."
::= { brconfig 16 }
brpsSNMPSetCommunity1 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SNMP Set Community Name #1."
::= { brconfig 17 }
brpsSNMPSetCommunity2 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SNMP Set Community Name #2."
::= { brconfig 18 }
brpsTestPage OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting any value generates a test page on all ports."
::= { brcontrol 1 }
brpsSetDefault OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting the value 5AA5h (23205) resets all parameters to their factory default value."
::= { brcontrol 2 }
brpsReset OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting the value 55AAh (21930) causes the print server to perform a soft reset."
::= { brcontrol 3 }
brpsProtectModeEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the protect mode is not enabled. 1 indicates protect mode
is enabled."
::= { brcontrol 4 }
brpsProtectPassword OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"protect password."
::= { brcontrol 5 }
brpsPortCount OBJECT-TYPE
SYNTAX INTEGER (0..32)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of ports on this print server."
::= { brport 1 }
brpsPortInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsPortInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the attributes of a port."
::= { brport 2 }
brpsPortInfoEntry OBJECT-TYPE
SYNTAX BrpsPortInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the port table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brpsPortIndex }
::= { brpsPortInfoTable 1 }
BrpsPortInfoEntry ::=
SEQUENCE {
brpsPortIndex
INTEGER,
brpsPortName
DisplayString,
brpsPortType
INTEGER,
brpsPortStatus
INTEGER,
brpsPortStatusString
DisplayString,
brpsPortProtocol
INTEGER,
brpsPortQueueSize
INTEGER,
brpsPortDescriptionString
DisplayString,
brpsPortInfoString
DisplayString,
brpsPortHTTPExtensions
INTEGER,
brpsPortSNMPExtensions
INTEGER,
brpsPortAttribute
DisplayString,
brpsPortBinaryMode
INTEGER,
brpsPortInhibitDatagramSupport
INTEGER
}
brpsPortIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port number."
::= { brpsPortInfoEntry 1 }
brpsPortName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port name."
::= { brpsPortInfoEntry 2 }
brpsPortType OBJECT-TYPE
SYNTAX INTEGER {
parallel(1),
serial(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Type of port."
::= { brpsPortInfoEntry 3 }
brpsPortStatus OBJECT-TYPE
SYNTAX INTEGER (0..31)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port status as a 32 bit integer."
::= { brpsPortInfoEntry 4 }
brpsPortStatusString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port status description. Reflects the printer's front panel display
on internal print server interfaces."
::= { brpsPortInfoEntry 5 }
brpsPortProtocol OBJECT-TYPE
SYNTAX INTEGER (0..12)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Protocol currently printing on this port."
::= { brpsPortInfoEntry 6 }
brpsPortQueueSize OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of protocols waiting to print on this port."
::= { brpsPortInfoEntry 7 }
brpsPortDescriptionString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..50) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port description. Reflects the device ID of the printer
connected to the port."
::= { brpsPortInfoEntry 8 }
brpsPortInfoString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port status information. More information about the port status."
::= { brpsPortInfoEntry 9 }
brpsPortHTTPExtensions OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the printer on this port does not support HTTP,
1 indicates that the printer does support HTTP."
::= { brpsPortInfoEntry 10 }
brpsPortSNMPExtensions OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the printer on this port does not support SNMP,
1 indicates that the printer does support SNMP."
::= { brpsPortInfoEntry 11 }
brpsPortAttribute OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Port attribute."
::= { brpsPortInfoEntry 12 }
brpsPortBinaryMode OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Port binary mode."
::= { brpsPortInfoEntry 13 }
brpsPortInhibitDatagramSupport OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the inhibit datagram is not supported.
1 indicates the inhibit datagram is supported."
::= { brpsPortInfoEntry 14 }
brpsServiceCount OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of services on this print server."
::= { brservice 1 }
brpsServiceInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsServiceInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the attributes of a service."
::= { brservice 2 }
brpsServiceInfoEntry OBJECT-TYPE
SYNTAX BrpsServiceInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the services table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brpsServiceIndex }
::= { brpsServiceInfoTable 1 }
BrpsServiceInfoEntry ::=
SEQUENCE {
brpsServiceIndex
INTEGER,
brpsServiceName
DisplayString,
brpsServicePort
INTEGER,
brpsServiceFilter
INTEGER,
brpsServiceBOT
INTEGER,
brpsServiceEOT
INTEGER,
brpsServiceMatch
INTEGER,
brpsServiceReplace
INTEGER,
brpsServiceTCPPort
INTEGER,
brpsServiceNDSTree
DisplayString,
brpsServiceNDSContext
OCTET STRING,
brpsServiceVines
DisplayString,
brpsServiceObsolete
INTEGER,
brpsServiceNetwareServerCount
INTEGER,
brpsServiceReceiveOnly
INTEGER,
brpsServiceTCPQueued
INTEGER,
brpsServiceProtocolLAT
INTEGER,
brpsServiceProtocolTCPIP
INTEGER,
brpsServiceProtocolNetware
INTEGER,
brpsServiceProtocolAppleTalk
INTEGER,
brpsServiceProtocolBanyan
INTEGER,
brpsServiceProtocolDLC
INTEGER,
brpsServiceProtocolNetBEUI
INTEGER,
brpsServiceNetwareServerMode
INTEGER,
brpsServiceNetwareRemotePrinterNum
INTEGER,
brpsServiceProtocolIPP
INTEGER,
brpsServiceAppleTalkType
DisplayString
}
brpsServiceIndex OBJECT-TYPE
SYNTAX INTEGER (1..32)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The service number."
::= { brpsServiceInfoEntry 1 }
brpsServiceName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The service name."
::= { brpsServiceInfoEntry 2 }
brpsServicePort OBJECT-TYPE
SYNTAX INTEGER (0..31)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number assigned to this service."
::= { brpsServiceInfoEntry 3 }
brpsServiceFilter OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Filter number assigned to this service."
::= { brpsServiceInfoEntry 4 }
brpsServiceBOT OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Beginning of text string number assigned to this service."
::= { brpsServiceInfoEntry 5 }
brpsServiceEOT OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"End of text string number assigned to this service."
::= { brpsServiceInfoEntry 6 }
brpsServiceMatch OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Match string number assigned to this service."
::= { brpsServiceInfoEntry 7 }
brpsServiceReplace OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Replace string number assigned to this service."
::= { brpsServiceInfoEntry 8 }
brpsServiceTCPPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TCP Port number assigned to this service."
::= { brpsServiceInfoEntry 9 }
brpsServiceNDSTree OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NDS Tree."
::= { brpsServiceInfoEntry 10 }
brpsServiceNDSContext OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NDS Context in Unicode."
::= { brpsServiceInfoEntry 11 }
brpsServiceVines OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Vines StreetTalk name for this service."
::= { brpsServiceInfoEntry 12 }
brpsServiceObsolete OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Obsolete parameter that is no longer used"
::= { brpsServiceInfoEntry 13 }
brpsServiceNetwareServerCount OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of Netware servers enabled on this service. Modifying the
value will truncate the server list to the specified number of servers.
If the value set is greater than the number of servers currently on the
list, then the list will be unchanged."
::= { brpsServiceInfoEntry 14 }
brpsServiceReceiveOnly OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the service will only receive data, any printer
responses will be discarded."
::= { brpsServiceInfoEntry 15 }
brpsServiceTCPQueued OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the raw TCP connections to the port will be
queued while waiting for the port to become available"
::= { brpsServiceInfoEntry 16 }
brpsServiceProtocolLAT OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the LAT protocol will be available on this service."
::= { brpsServiceInfoEntry 17 }
brpsServiceProtocolTCPIP OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the TCP/IP protocol will be available on this service."
::= { brpsServiceInfoEntry 18 }
brpsServiceProtocolNetware OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the Netware protocol will be available on this service."
::= { brpsServiceInfoEntry 19 }
brpsServiceProtocolAppleTalk OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the AppleTalk protocol will be available on this service."
::= { brpsServiceInfoEntry 20 }
brpsServiceProtocolBanyan OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the Banyan protocol will be available on this service."
::= { brpsServiceInfoEntry 21 }
brpsServiceProtocolDLC OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the DLC protocol will be available on this service."
::= { brpsServiceInfoEntry 22 }
brpsServiceProtocolNetBEUI OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the NetBEUI protocol will be available on this service."
::= { brpsServiceInfoEntry 23 }
brpsServiceNetwareServerMode OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Netware mode for this service. 0 = Queue Server, 1 = Remote Printer"
::= { brpsServiceInfoEntry 24 }
brpsServiceNetwareRemotePrinterNum OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Remote Printer Number for this service"
::= { brpsServiceInfoEntry 25 }
brpsServiceProtocolIPP OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the IPP protocol will be available on this service."
::= { brpsServiceInfoEntry 26 }
brpsServiceAppleTalkType OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"AppleTalk type."
::= { brpsServiceInfoEntry 27 }
brpsServiceStringLimit OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of service strings supported by the print server."
::= { brservice 3 }
brpsServiceStringInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsServiceStringInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the service BOT/EOT/MATCH/REPLACE strings defined."
::= { brservice 4 }
brpsServiceStringInfoEntry OBJECT-TYPE
SYNTAX BrpsServiceStringInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the service string table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brpsServiceStringIndex }
::= { brpsServiceStringInfoTable 1 }
BrpsServiceStringInfoEntry ::=
SEQUENCE {
brpsServiceStringIndex
INTEGER,
brpsServiceString
DisplayString
}
brpsServiceStringIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The string number."
::= { brpsServiceStringInfoEntry 1 }
brpsServiceString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The character string definition suitable for displaying."
::= { brpsServiceStringInfoEntry 2 }
brpsServiceStringCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of service strings currently defined on the print server."
::= { brservice 5 }
brpsServiceFilterCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of service filters implemented by the device."
::= { brservice 6 }
brpsLATSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the LAT protocol is not supported. 1 indicates LAT
support is implemented by the firmware"
::= { brlat 1 }
brpsLATEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LAT protocol is not enabled. 1 indicates that the LAT
protocol is enabled. Writing a non-zero value will enable the LAT
protocol if it is supported by the firmware."
::= { brlat 2 }
brpsLATCircuitTimer OBJECT-TYPE
SYNTAX INTEGER (10..499)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Minimum time (in milliseconds) between transmissions to the host. The
default of 10 normally provides the best performance."
::= { brlat 3 }
brpsLATKeepAliveTimer OBJECT-TYPE
SYNTAX INTEGER (0..60000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"How often in seconds a packet is transmitted to keep a connection alive."
::= { brlat 4 }
brpsLATReceiveBufferMax OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LAT receive buffer max size."
::= { brlat 5 }
brpsLATTransmitBufferMax OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LAT transmit buffer max size."
::= { brlat 6 }
brpsLATTimeout OBJECT-TYPE
SYNTAX INTEGER (0..499)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LAT inactivity timeout (sec)."
::= { brlat 7 }
brpsLATGroup OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..7) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"LAT group membership (mm-[nn])."
::= { brlat 8 }
brpsTCPIPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the TCP/IP protocol is not supported. 1 indicates TCP/IP
support is implemented by the firmware"
::= { brtcpip 1 }
brpsTCPIPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the TCP/IP protocol is not enabled. 1 indicates that the
TCP/IP protocol is enabled. Writing a non-zero value will enable the
TCP/IP protocol if it is supported by the firmware."
::= { brtcpip 2 }
brpsTCPIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IP Address assigned to the print server."
::= { brtcpip 3 }
brpsTCPIPSubnetMask OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Subnet mask assigned to the print server."
::= { brtcpip 4 }
brpsTCPIPGateway OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Gateway/Router address assigned to the print server."
::= { brtcpip 5 }
brpsTCPIPMethod OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method used to determine the IP Address. AUTO tries all protocols.
STATIC uses the configured address. DHCP, BOOTP, and RARP use only
that protocol."
::= { brtcpip 6 }
brpsTCPIPTimeout OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Timeout used for LPD connections."
::= { brtcpip 7 }
brpsTCPIPBootTries OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of attempts to use BOOTP, RARP, and DHCP."
::= { brtcpip 8 }
brpsTCPIPMaxWindow OBJECT-TYPE
SYNTAX INTEGER (1500..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum window size for TCP connections. Due to resource limitations
setting the window to values greater than 10240 is not recommended."
::= { brtcpip 9 }
brpsTCPIPRARPNoSubnet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If enabled, do not set the subnet mask based on the RARP response."
::= { brtcpip 10 }
brpsTCPIPRARPNoGateway OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If enabled, do not set the gateway/router address based on the RARP response."
::= { brtcpip 11 }
brpsTCPIPUpdate OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(6) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Hardware MAC address to be updated. This value is write only. Will
read back as zeros."
::= { brtcpip 12 }
brpsTCPIPBanner OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LPR banner print is not enabled.
1 indicates that the LPR banner print is enabled."
::= { brtcpip 13 }
brpsTCPIPFastTimeoutEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the fast timeout is not enabled.
1 indicates that the fast timeout is enabled."
::= { brtcpip 14 }
brpsTCPIPLPRRetryEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LPR print retry is not enabled.
1 indicates that the LPR print retry is enabled."
::= { brtcpip 15 }
brpsTCPIPUseMethod OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method type that used set up TCP/IP configuration."
::= { brtcpip 16 }
brpsTCPIPMethodServer OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If TCP/IP configuration is setted up by any protocol server,
this entry indicates the IP address of the server."
::= { brtcpip 17 }
brpsTCPIPAccessTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsTCPIPAccessEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the list of IP address of node that has
parmittion for access.Up to 16 Netware addresses can be enabled."
::= { brtcpip 18 }
brpsTCPIPAccessEntry OBJECT-TYPE
SYNTAX BrpsTCPIPAccessEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the TCP/IP access table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brpsTCPIPAccessIndex }
::= { brpsTCPIPAccessTable 1 }
BrpsTCPIPAccessEntry ::=
SEQUENCE {
brpsTCPIPAccessIndex
INTEGER,
brpsTCPIPAccessNodeAddress
IpAddress,
brpsTCPIPAccessSubnetMask
IpAddress
}
brpsTCPIPAccessIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The TCP/IP access table's index."
::= { brpsTCPIPAccessEntry 1 }
brpsTCPIPAccessNodeAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IP address of node that has parmittion for access."
::= { brpsTCPIPAccessEntry 2 }
brpsTCPIPAccessSubnetMask OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Subnet mask of node that has parmittion for access."
::= { brpsTCPIPAccessEntry 3 }
brpsAdvancedTCPIPAccessSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Advanced TCP/IP Access is not supported.
1 indicates Advanced TCP/IP Access support is implemented
by the firmware"
::= { brtcpip 19 }
brpsAdvancedTCPIPAccessEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Advanced TCP/IP Access is not enabled.
1 indicates that the Advanced TCP/IP Access is enabled."
::= { brtcpip 20 }
brpsAdvancedTCPIPAccessAdministratorIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Administrator IPAddress."
::= { brtcpip 21 }
brpsAdvancedTCPIPAccessSetting OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Advanced TCP/IP Access is reject.
1 indicates that the Advanced TCP/IP Access is Accept."
::= { brtcpip 22 }
brpsNetwareSupported OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Netware protocol is not supported. 1 indicates Netware
support is implemented by the firmware. 2 indicates that Netware NEST NDS
support is implemented by the firmware."
::= { brnetware 1 }
brpsNetwareEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Netware protocol is not enabled. 1 indicates that the
Netware protocol is enabled. Writing a non-zero value will enable the
Netware protocol if it is supported by the firmware."
::= { brnetware 2 }
brpsNetwareFrameType OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The frame type to be used as follows: 0 = Automatic, 1 = Ethernet 802.3,
2 = Ethernet II, 3 = Ethernet 802.2, 4 = Ethernet SNAP."
::= { brnetware 3 }
brpsNetwarePollFreq OBJECT-TYPE
SYNTAX INTEGER (2..60)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"File server polling frequency in seconds."
::= { brnetware 4 }
brpsNetwareAdvFreq OBJECT-TYPE
SYNTAX INTEGER (0..210)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Print server advertising frequency in seconds."
::= { brnetware 5 }
brpsNetwarePassword OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Netware login password."
::= { brnetware 6 }
brpsNetwareRestart OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting any value will restart the Netware protocol."
::= { brnetware 7 }
brpsNetwareServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsNetwareServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the list of enabled Netware servers.
Up to 16 Netware servers can be enabled. If the service is
configured for remote printer mode, then only the first
enabled server is used and it should specify a print server."
::= { brnetware 8 }
brpsNetwareServerEntry OBJECT-TYPE
SYNTAX BrpsNetwareServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the Netware server table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brpsServiceIndex, brpsNetwareServerIndex }
::= { brpsNetwareServerTable 1 }
BrpsNetwareServerEntry ::=
SEQUENCE {
brpsNetwareServerIndex
INTEGER,
brpsNetwareServerName
DisplayString
}
brpsNetwareServerIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Netware server number."
::= { brpsNetwareServerEntry 1 }
brpsNetwareServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Netware server name. Specifies a print server if the service is
in remote printer mode, or a file server if the service is in
queue server mode"
::= { brpsNetwareServerEntry 2 }
brpsNetwarePasswordSet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Returns 1 if the Netware login password is set, 0 if not set."
::= { brnetware 9 }
brpsNDSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates NDS is not supported. 1 indicates NDS is implemented
by the firmware"
::= { brnetware 10 }
brpsNetwareEtherIINetInfo OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Ethernet II network information."
::= { brnetware 11 }
brpsNetwareEtherIICount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Ethernet II network counter"
::= { brnetware 12 }
brpsNetware8022NetInfo OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IEEE 802.2 network information."
::= { brnetware 13 }
brpsNetware8022Count OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IEEE 802.2 network counter."
::= { brnetware 14 }
brpsNetware8023NetInfo OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IEEE 802.3 network information."
::= { brnetware 15 }
brpsNetware8023Count OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IEEE 802.3 network information."
::= { brnetware 16 }
brpsNetwareSNAPNetInfo OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SNAP network information."
::= { brnetware 17 }
brpsNetwareSNAPCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SNAP network count."
::= { brnetware 18 }
brpsNetwareServicingServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Netware server name."
::= { brnetware 19 }
brpsNetwareServicingQueueName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Netware queue name."
::= { brnetware 20 }
brpsNetwareServicingServerCount OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of netware servers."
::= { brnetware 21 }
brpsNetwareServicingQueueCount OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of netware queues."
::= { brnetware 22 }
brpsNetwarePrintJob OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of netware print job."
::= { brnetware 23 }
brpsAppleTalkSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the AppleTalk protocol is not supported. 1 indicates AppleTalk
support is implemented by the firmware"
::= { brappletalk 1 }
brpsAppleTalkEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the AppleTalk protocol is not enabled. 1 indicates that the
AppleTalk protocol is enabled. Writing a non-zero value will enable the
AppleTalk protocol if it is supported by the firmware."
::= { brappletalk 2 }
brpsAppleTalkZone OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The AppleTalk zone the print server belongs to."
::= { brappletalk 3 }
brpsAppleTalkPrintJob OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of AppleTalk print job."
::= { brappletalk 4 }
brpsAppleTalkReadByte OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of read bytes."
::= { brappletalk 5 }
brpsAppleTalkWriteByte OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of write bytes."
::= { brappletalk 6 }
brpsAppleTalkReadError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of read error."
::= { brappletalk 7 }
brpsAppleTalkWriteError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of write error."
::= { brappletalk 8 }
brpsBanyanSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Banyan protocol is not supported. 1 indicates Banyan
support is implemented by the firmware"
::= { brbanyan 1 }
brpsBanyanEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Banyan protocol is not enabled. 1 indicates that the
Banyan protocol is enabled. Writing a non-zero value will enable the
Banyan protocol if is is supported by the firmware."
::= { brbanyan 2 }
brpsBanyanLoginName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Banyan login name."
::= { brbanyan 3 }
brpsBanyanPassword OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..16) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Banyan login password."
::= { brbanyan 4 }
brpsBanyanHopCount OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of hops between the print server and the Banyan file server."
::= { brbanyan 5 }
brpsBanyanTimeout OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Timeout in seconds for a Banyan print job."
::= { brbanyan 6 }
brpsBanyanPasswordSet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Returns 1 if the Banyan login password is set, 0 if not set."
::= { brbanyan 7 }
brpsBanyanIPNetworkID1 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(8) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IP Network ID."
::= { brbanyan 8 }
brpsBanyanIPNetworkID2 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(4) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IP Network ID."
::= { brbanyan 9 }
brpsBanyanRouter1 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(8) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Router ID."
::= { brbanyan 10 }
brpsBanyanRouter2 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(4) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Router ID."
::= { brbanyan 11 }
brpsBanyanIPPacket OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of IP Packet."
::= { brbanyan 12 }
brpsBanyanErrorCS OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of CS error."
::= { brbanyan 13 }
brpsBanyanErrorPT OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of PT error."
::= { brbanyan 14 }
brpsBanyanErrorLE OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of LE error."
::= { brbanyan 15 }
brpsBanyanPrintServerStatus OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Banyan print server status."
::= { brbanyan 16 }
brpsBanyanServerAddress1 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(8) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Banyan server address."
::= { brbanyan 17 }
brpsBanyanServerAddress2 OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(4) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Banyan server address."
::= { brbanyan 18 }
brpsBanyanIPCConnectionInformation OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IPC connection information."
::= { brbanyan 19 }
brpsBanyanIPCSequenceError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IPC sequence error."
::= { brbanyan 20 }
brpsBanyanIPCListen OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IPC listen."
::= { brbanyan 21 }
brpsBanyanSPPConnectionInformation OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SPP connection information."
::= { brbanyan 22 }
brpsBanyanSPPSequenceError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SPP sequence error."
::= { brbanyan 23 }
brpsBanyanSPPListen OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"SPP listen."
::= { brbanyan 24 }
brpsEmailSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the POP3/SMTP email protocols are not supported. 1 indicates email
support is implemented by the firmware"
::= { bremail 1 }
brpsEmailEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the POP3/SMTP email protocols are not enabled. 1 indicates that the
email protocols are enabled. Writing a non-zero value will enable the
email protocols if they are supported by the firmware."
::= { bremail 2 }
brpsPOP3Address OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the POP3 server."
::= { bremail 3 }
brpsSMTPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the SMTP server."
::= { bremail 4 }
brpsPOP3Name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The POP3 mailbox name."
::= { bremail 5 }
brpsPOP3Password OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The POP3 mailbox password."
::= { bremail 6 }
brpsPOP3PollFreq OBJECT-TYPE
SYNTAX INTEGER (10..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The POP3 polling frequency in seconds."
::= { bremail 7 }
brpsPOP3Timeout OBJECT-TYPE
SYNTAX INTEGER (10..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The POP3 timeout in minutes."
::= { bremail 8 }
brpsPOP3PasswordSet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Returns 1 if the POP3 password is set, 0 if not set."
::= { bremail 9 }
brpsPOP3TotalMessage OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 message."
::= { bremail 10 }
brpsPOP3TotalConnect OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 connect."
::= { bremail 11 }
brpsPOP3TotalConnectFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 connect error."
::= { bremail 12 }
brpsPOP3TotalConnectionLost OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 connection lost."
::= { bremail 13 }
brpsPOP3TotalUserFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 user error."
::= { bremail 14 }
brpsPOP3TotalPasswordFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 pass error."
::= { bremail 15 }
brpsPOP3TotalIOError OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 I/O error."
::= { bremail 16 }
brpsSMTPTotalMessage OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of SMTP message."
::= { bremail 17 }
brpsSMTPTotalConnect OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of SMTP connect."
::= { bremail 18 }
brpsSMTPTotalConnectFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of SMTP connect error."
::= { bremail 19 }
brpsSMTPTotalRecvFromFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of SMTP recvfrom error."
::= { bremail 20 }
brpsSMTPTotalSendToFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of SMTP recvfrom error."
::= { bremail 21 }
brpsPOP3Supported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the POP3 protocol is not supported.
1 indicates the POP3 protocol is implemented by the firmware"
::= { bremail 101 }
brpsSMTPServerAuthMethod OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the user is not authenticated to the SMTP Server.
1 indicates the user is authenticated to the SMTP Server using SMTP-AUTH.
2 indicates the user is authenticated to the SMTP Server using POP before SMTP."
::= { bremail 102 }
brpsSMTPAUTHUsername OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..60) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The username of SMTP server's account."
::= { bremail 103 }
brpsSMTPAUTHPassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The password of SMTP server's account."
::= { bremail 104 }
brpsSMTPAUTHPasswordSet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Returns 1 if the SMTP server login password is set, 0 if not set."
::= { bremail 105 }
brpsSmtpAUTHTimeout OBJECT-TYPE
SYNTAX INTEGER (10..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The SMTP-AUTH timeout in seconds."
::= { bremail 106 }
brpsPOPbeforeSMTPWait OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The wait time in mili seconds between POP logging in and SMTP sending."
::= { bremail 107 }
brpsAPOPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the APOP is not enabled.
1 indicates the APOP is enabled."
::= { bremail 108 }
brpsSMTPEnhancedAuthSupported OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Bit0 indicates 'no authentication'.
Bit1 indicates 'SMTP-AUTH'.
Bit2 indicates 'POP before SMTP'."
::= { bremail 150 }
brpsAPOPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the APOP is not supported.
1 indicates the APOP is supported."
::= { bremail 151 }
brpsEmailSendTestSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Email Sending Test is not supported.
1 indicates the Email Sending Test is supported."
::= { bremail 152 }
brpsEmailRecvTestSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Email Receiving Test is not supported.
1 indicates the Email Receiving Test is supported."
::= { bremail 153 }
brpsChangeSMTPPortSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates to change the SMTP port number is not supported.
1 indicates to change the SMTP port number is supported."
::= { bremail 154 }
brpsSMTPPortNumber OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number of connection to SMTP server."
::= { bremail 155 }
brpsChangePOP3PortSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates to change the POP3 port number is not supported.
1 indicates to change the POP3 port number is supported."
::= { bremail 156 }
brpsPOP3PortNumber OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number of connection to POP3 server."
::= { bremail 157 }
brpsTmpSMTPServerName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
The FQDN name of the SMTP server."
::= { bremail 170 }
brpsTmpSMTPServerAuthMethod OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
0 indicates the user is not authenticated to the SMTP Server.
1 indicates the user is authenticated to the SMTP Server using SMTP-AUTH.
2 indicates the user is authenticated to the SMTP Server using POP before SMTP."
::= { bremail 171 }
brpsTmpSMTPAUTHUsername OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..60) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
The username of SMTP server's account."
::= { bremail 172 }
brpsTmpSMTPAUTHPassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
The password of SMTP server's account."
::= { bremail 173 }
brpsTmpPOP3ServerName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending/Receiving Test.
The FQDN name of the POP3 server."
::= { bremail 174 }
brpsTmpPOP3Name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending/Receiving Test.
The POP3 mailbox name."
::= { bremail 175 }
brpsTmpPOP3Password OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending/Receiving Test.
The POP3 mailbox password."
::= { bremail 176 }
brpsTmpPrintersEmailaddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
The Printers Email Address"
::= { bremail 177 }
brpsTmpAPOPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending/Receiving Test.
0 indicates the APOP is not enabled.
1 indicates the APOP is enabled."
::= { bremail 178 }
brpsTmpSMTPAUTHPasswordModified OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the SMTP server password is not modified.
1 indicates the SMTP server password is modified."
::= { bremail 179 }
brpsTmpPOP3PasswordModified OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the POP3 server password is not modified.
1 indicates the POP3 server password is modified."
::= { bremail 180 }
brpsTmpSMTPPortNumber OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending Test.
The port number of connection to SMTP server."
::= { bremail 181 }
brpsTmpPOP3PortNumber OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Temporary Setting for Email Sending/Receiving Test.
The port number of connection to POP3 server."
::= { bremail 182 }
brpsEmailSendTestMail OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the testmail is not sended at Email Sending Test.
1 indicates the testmail is sended at Email Sending Test."
::= { bremail 200 }
brpsEmailTestDestinationAddress OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..80) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The destination Email Address of Email Sending Test."
::= { bremail 201 }
brpsEmailSendTestCall OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Email Sending Test is not called on. ('READY')
1 indicates the Email Sending Test is called on. ('START')
2 indicates the Email Sending Test is canceled. ('CANCEL')"
::= { bremail 210 }
brpsEmailRecvTestCall OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Email Receiving Test is not called on. ('READY')
1 indicates the Email Receiving Test is called. ('START')
2 indicates the Email Receiving Test is canceled. ('CANCEL')"
::= { bremail 211 }
brpsEmailSendRecvTestCall OBJECT-TYPE
SYNTAX INTEGER (0..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Email Sending and Receiving Test is not called on. ('READY')
1 indicates the Email Sending and Receiving Test is called. ('START')
2 indicates the Email Sending and Receiving Test is canceled. ('CANCEL')"
::= { bremail 212 }
brpsEmailTestResult OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This Value is divided into 15-8bit and 7-0bit.
15-8bit indicates Email Sending Test's Result.
7-0bit indicates Email Receiving Test's Result.
(However, the value from 0x00 to 0x04 is only set to 7-0bit.)
0x00 indicates the Email Test is not running.
0x01 indicates the Email Test is running. ('BUSY')
0x02 indicates the Email Test is canceled.('CANCELED')
0x03 indicates the Email Test is Locked by another Email Test process.(LOCKED)
0x04 indicates the Email Test is not executed. -- unused
0x10 indicates the Status 'Fatal Error is occurred during Email Testing'.
0x20 indicates the Status 'Invalid value is set in SMTP Server Address'.
0x21 indicates the Status 'Invalid value is set in SMTP-AUTH Account Name'.
0x22 indicates the Status 'Invalid value is set in SMTP-AUTH Password'.
0x30 indicates the Status 'Invalid value is set in POP3 Server Address'.
0x31 indicates the Status 'Invalid value is set in POP3 Account Name'.
0x32 indicates the Status 'Invalid value is set in POP3 Account Password'.
0x40 indicates the Status 'Invalid value is set in POP3 Printer E-mail Address'.
0x41 indicates the Status 'Invalid value is set in Destination E-mail Address'.
0x50 indicates the Status 'Sending OK'.
0x51 indicates the Status 'Cannot locate SMTP server'.
0x52 indicates the Status 'Cannot connect to SMTP server'.
0x53 indicates the Status 'Cannot authenticate with SMTP server by using method'.
0x54 indicates the Status 'Authentication failure in SMTP server'.
0x55 indicates the Status 'Email Sending Timeout' -- unused
0x60 indicates the Status 'Receiving OK'.
0x61 indicates the Status 'Cannot locate POP3 server'.
0x62 indicates the Status 'Cannot connect to POP3 server'.
0x63 indicates the Status 'Authentication failure in POP3 server'.
0x64 indicates the Status 'Cannot authenticate with POP3 server by using method'.
0x65 indicates the Status 'Email Receiving Timeout' -- unused
0x66 indicates the Email Test is Locked by another Email process.
0x70 indicates the Status 'Cannot resolve the host name (DNS Error)'."
::= { bremail 220 }
brpsPOP3TotalAPOPFailure OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of POP3 APOP error."
::= { bremail 221 }
brpsDLCSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the DLC protocol is not supported. 1 indicates DLC
support is implemented by the firmware"
::= { brdlc 1 }
brpsDLCEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the DLC protocol is not enabled. 1 indicates that the
DLC protocol is enabled. Writing a non-zero value will enable the
DLC protocol if is is supported by the firmware."
::= { brdlc 2 }
brpsDLCPrintStatus OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"DLC print status."
::= { brdlc 3 }
brpsDLCLLCState OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LLC status."
::= { brdlc 4 }
brpsDLCLLCConnectHost OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LLC connected host name."
::= { brdlc 5 }
brpsDLCLLCLastIFrame OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"LLC last valid I-frame."
::= { brdlc 6 }
brpsDLCLLCRecvPacket OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Counter of LLC receive packets."
::= { brdlc 7 }
brpsDLCLLCPortStatus OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Port status."
::= { brdlc 8 }
brpsIPPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the IPP protocol is not supported. 1 indicates IPP
support is implemented by the firmware"
::= { bripp 1 }
brpsIPPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the IPP protocol is not enabled. 1 indicates that the IPP
protocol is enabled. Writing a non-zero value will enable the IPP
protocol if it is supported by the firmware."
::= { bripp 2 }
brIPPRegularPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the IPP regular port is not enabled.
1 indicates that the IPP regular port is enabled."
::= { bripp 3 }
brIPPSSLPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the IPP SSL port is not enabled.
1 indicates that the IPP SSL port is enabled."
::= { bripp 4 }
brIPPOriginalPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the IPP original port is not enableed.
1 indicates that the IPP original port is enabled."
::= { bripp 5 }
brpsNtSendSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the NtSend protocol is not supported. 1 indicates NtSend
support is implemented by the firmware"
::= { brntsend 1 }
brpsNtSendEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the NtSend protocol is not enabled. 1 indicates that the
NtSend protocol is enabled. Writing a non-zero value will enable the
NtSend protocol if it is supported by the firmware."
::= { brntsend 2 }
brpsFirmwareIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP address of the host from which to TFTP GET the firmware."
::= { brfirmware 1 }
brpsFirmwareHost OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Netware server name from which to fetch the firmware."
::= { brfirmware 2 }
brpsFirmwareFile OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The firmware file to be reloaded."
::= { brfirmware 3 }
brpsFirmwareReload OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting a value of 0x5A will cause the print server to begin attempts to
reload the firmware within 5 seconds. Further attempts to read or modify
the configuration are not recommended until after the firmware has been
reloaded."
::= { brfirmware 4 }
brpsFirmwareDescription OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Firmware version and date."
::= { brfirmware 5 }
brpsFirmwareXModem OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Set 1 execute XMODEM mode."
::= { brfirmware 6 }
brpsFirmwareAdvancedAddressSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Firmware Advanced Address is not supported.
1 indicates Firmware Advanced Address support is implemented
by the firmware"
::= { brfirmware 7 }
brpsFirmwareAdvancedAddress OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The address of the host from which to TFTP GET the firmware."
::= { brfirmware 8 }
brpsNetBEUISupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the NetBEUI protocol is not supported. 1 indicates NetBEUI
support is implemented by the firmware"
::= { brnetbeui 1 }
brpsNetBEUIEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the NetBEUI protocol is not enabled. 1 indicates that the
NetBEUI protocol is enabled. Writing a non-zero value will enable the
NetBEUI protocol if is is supported by the firmware."
::= { brnetbeui 2 }
brpsNetBEUIDomain OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..15) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NetBEUI domain name."
::= { brnetbeui 3 }
brpsNetBIOSIPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the NetBIOS IP protocol is not supported. 1 indicates NetBIOS IP
support is implemented by the firmware"
::= { brnetbeui 4 }
brpsNetBIOSIPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the NetBIOS IP protocol is not enabled. 1 indicates that the
NetBIOS IP protocol is enabled. Writing a non-zero value will enable the
NetBIOS IP protocol if is is supported by the firmware."
::= { brnetbeui 5 }
brpsNetBIOSIPMethod OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method used to determine the IP Address of the WINS server.
AUTO tries all protocols (currently only DHCP is tried).
STATIC uses the configured address."
::= { brnetbeui 6 }
brpsNetBIOSPrimaryWINSAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the primary WINS server."
::= { brnetbeui 7 }
brpsNetBIOSSecondaryWINSAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the secondary WINS server."
::= { brnetbeui 8 }
brpsNetBIOSPrintingSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the NetBIOS IP protocol printing is not supported.
1 indicates the NetBIOS IP protocol printing is supported."
::= { brnetbeui 101 }
brLPDType OBJECT-TYPE
SYNTAX INTEGER (0..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { broriginaltcpip 1 }
brFTPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the FTP protocol is not supported. 1 indicates FTP
support is implemented by the firmware"
::= { broriginalftp 1 }
brFTPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the FTP protocol is not enabled. 1 indicates that the FTP
protocol is enabled. Writing a non-zero value will enable the FTP
protocol if it is supported by the firmware."
::= { broriginalftp 2 }
brUPnPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the UPnP protocol is not supported.
1 indicates UPnP support is implemented by the firmware"
::= { broriginalupnp 1 }
brUPnPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the UPnP protocol is not enabled.
1 indicates that the UPnP protocol is enabled.
Writing a non-zero value will enable the UPnP
protocol if it is supported by the firmware."
::= { broriginalupnp 2 }
brAPIPASupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the APIPA protocol is not supported.
1 indicates APIPA support is implemented by the firmware"
::= { broriginalapipa 1 }
brAPIPAEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the APIPA protocol is not enabled.
1 indicates that the APIPA protocol is enabled.
Writing a non-zero value will enable the APIPA
protocol if it is supported by the firmware."
::= { broriginalapipa 2 }
brmDNSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the mDNS protocol is not supported.
1 indicates mDNS support is implemented by the firmware"
::= { broriginalmdns 1 }
brmDNSEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the mDNS protocol is not enabled.
1 indicates that the mDNS protocol is enabled.
Writing a non-zero value will enable the mDNS
protocol if it is supported by the firmware."
::= { broriginalmdns 2 }
brmDNSPrinterName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"mDNS Service Name"
::= { broriginalmdns 3 }
brLAASupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value indicate if the locally administered addressing is supported.
0: Not Supported
1: Supported"
::= { broriginalLAA 1 }
brLAAMacAddress OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(6) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A locally administered address (LAA) that replaces the factory-assigned
MAC address (UAA: universally administered address).
If this setting is all-zero address (i.e. 6 bytes of zeros), the
factory-assigned
MAC address is used as the MAC address of the device.
The LAA address must start with X2, X6, XA, or XE, where X is any
hexadecimal digit 0 to F."
::= { broriginalLAA 2 }
brIPv6Supported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the IPv6 protocol is not supported.
1 indicates IPv6 support is implemented by the firmware"
::= { broriginalIPv6 1 }
brIPv6Enable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the IPv6 protocol is not enabled.
1 indicates that the IPv6 protocol is enabled.
Writing a non-zero value will enable the IPv6
protocol if it is supported by the firmware."
::= { broriginalIPv6 2 }
brIPv6Priority OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the IPv6 protocol is low priority.
1 indicates that the IPv6 protocol is high priority."
::= { broriginalIPv6 3 }
brtelnetSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the telnet protocol is not supported.
1 indicates telnet support is implemented by the firmware"
::= { broriginaltelnet 1 }
brtelnetEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the telnet protocol is not enabled.
1 indicates that the telnet protocol is enabled.
Writing a non-zero value will enable the telnet
protocol if it is supported by the firmware."
::= { broriginaltelnet 2 }
brEWSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the EWS protocol is not supported.
1 indicates EWS support is implemented by the firmware"
::= { broriginalEWS 1 }
brEWSEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the EWS protocol is not enabled.
1 indicates that the EWS protocol is enabled.
Writing a non-zero value will enable the EWS
protocol if it is supported by the firmware."
::= { broriginalEWS 2 }
brEWSRegularPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the EWS regular port is not enabled.
1 indicates that the EWS regular port is enabled."
::= { broriginalEWS 3 }
brEWSSSLPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the EWS SSL port is not enabled.
1 indicates that the EWS SSL port is enabled."
::= { broriginalEWS 4 }
brSNMPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the SNMP protocol is not supported.
1 indicates SNMP support is implemented by the firmware"
::= { broriginalSNMP 1 }
brSNMPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the SNMP protocol is not enabled.
1 indicates that the SNMP protocol is enabled.
Writing a non-zero value will enable the SNMP
protocol if it is supported by the firmware."
::= { broriginalSNMP 2 }
brTFTPSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the TFTP protocol is not supported.
1 indicates TFTP support is implemented by the firmware"
::= { broriginalTFTP 1 }
brTFTPEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the TFTP protocol is not enabled.
1 indicates that the TFTP protocol is enabled.
Writing a non-zero value will enable the TFTP
protocol if it is supported by the firmware."
::= { broriginalTFTP 2 }
brHTTPSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the HTTPS/IPPS protocol is not supported.
1 indicates HTTPS/IPPS support is implemented by the firmware"
::= { broriginalHTTPS 1 }
brHTTPSEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the HTTPS/IPPS protocol is not enabled.
1 indicates that the HTTPS/IPPS protocol is enabled.
Writing a non-zero value will enable the HTTPS/IPPS
protocol if it is supported by the firmware."
::= { broriginalHTTPS 2 }
brLPDSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the LPD protocol is not supported.
1 indicates LPD support is implemented by the firmware"
::= { broriginalLPD 1 }
brLPDEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LPD protocol is not enabled.
1 indicates that the LPD protocol is enabled.
Writing a non-zero value will enable the LPD
protocol if it is supported by the firmware."
::= { broriginalLPD 2 }
brRawPortSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the RawPort protocol is not supported.
1 indicates RawPort support is implemented by the firmware"
::= { broriginalRawPort 1 }
brRawPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the RawPort protocol is not enabled.
1 indicates that the RawPort protocol is enabled.
Writing a non-zero value will enable the RawPort
protocol if it is supported by the firmware."
::= { broriginalRawPort 2 }
brLLTDSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the LLTD protocol is not supported.
1 indicates LLTD support is implemented by the firmware"
::= { broriginalLLTD 1 }
brLLTDEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LLTD protocol is not enabled.
1 indicates that the LLTD protocol is enabled.
Writing a non-zero value will enable the LLTD
protocol if it is supported by the firmware."
::= { broriginalLLTD 2 }
brWebServicesSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the WebServices protocol is not supported.
1 indicates WebServices support is implemented by the firmware"
::= { broriginalWebServices 1 }
brWebServicesEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the WebServices protocol is not enabled.
1 indicates that the WebServices protocol is enabled.
Writing a non-zero value will enable the WebServices
protocol if it is supported by the firmware."
::= { broriginalWebServices 2 }
brWebServicesRegularPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the WebServices regular port is not enabled.
1 indicates that the WebServices regular port is enabled."
::= { broriginalWebServices 3 }
brWebServicesSSLPortEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates that the WebServices SSL port is not enabled.
1 indicates that the WebServices SSL port is enabled."
::= { broriginalWebServices 4 }
brLLMNREnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LLMNR protocol is not enabled.
1 indicates that the LLMNR protocol is enabled."
::= { broriginalLLMNR 1 }
brProxySupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Proxy is not supported.
1 indicates Proxy is implemented by the firmware"
::= { broriginalproxy 1 }
brProxyEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Proxy is not enabled.
1 indicates that the Proxy is enabled.
Writing a non-zero value will enable the Proxy
if it is supported by the firmware."
::= { broriginalproxy 2 }
brProxyBypassServer OBJECT-TYPE
SYNTAX INTEGER {
off(1),
on(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"on(2) indicates the bypass proxy server for local addresses."
::= { broriginalproxy 3 }
brProxyServerCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of Proxy Server INDEX."
::= { broriginalproxy 11 }
brProxyServerInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrProxyServerInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Proxy Server Info."
::= { broriginalproxy 12 }
brProxyServerInfoEntry OBJECT-TYPE
SYNTAX BrProxyServerInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the ProxyServerInfo table. Rows cannot be created or deleted."
INDEX { brProxyServerInfoIndex }
::= { brProxyServerInfoTable 1 }
BrProxyServerInfoEntry ::=
SEQUENCE {
brProxyServerInfoIndex
INTEGER,
brProxyServerType
INTEGER,
brProxyServerName
OCTET STRING,
brProxyServerPort
INTEGER
}
brProxyServerInfoIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brProxyServerInfoEntry 1 }
brProxyServerType OBJECT-TYPE
SYNTAX INTEGER {
http(1),
secure(2),
ftp(3),
gopher(4),
socks(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Proxy server ID."
::= { brProxyServerInfoEntry 2 }
brProxyServerName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..80) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Proxy server name."
::= { brProxyServerInfoEntry 3 }
brProxyServerPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Proxy server port number."
::= { brProxyServerInfoEntry 4 }
brJobTerminationSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Job termination setting is not supported.
1 indicates the Job termination setting is implemented by the firmware"
::= { broriginalJobTermination 1 }
brJobTerminationEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Job termination setting is not enabled.
1 indicates the Job termination setting is enabled."
::= { broriginalJobTermination 2 }
brSNMPTrapTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrSNMPTrapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { broriginalSNMPTrap 1 }
brSNMPTrapEntry OBJECT-TYPE
SYNTAX BrSNMPTrapEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brSNMPTrapIndex }
::= { brSNMPTrapTable 1 }
BrSNMPTrapEntry ::=
SEQUENCE {
brSNMPTrapIndex
INTEGER,
brTCPIPServerAddress
IpAddress
}
brSNMPTrapIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brSNMPTrapEntry 1 }
brTCPIPServerAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Destination IP Address for SNMP Trap."
::= { brSNMPTrapEntry 2 }
brLegacyCompatible OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { broriginalLegacy 1 }
brDeviceNegotiationEncryptVer OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brSecurityGeneralStatus 1 }
brpsServerCertificateNum OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brSecurityGeneralStatus 2 }
brDeviceNegotiationGetChallenge OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(20) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brSecurityDeviceNegotiation 1 }
brDeviceNegotiationConfirmPassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(60) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { brSecurityDeviceNegotiation 2 }
brDeviceNegotiationChangePassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { brSecurityDeviceNegotiation 3 }
brpsWLanDot11Supported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Flags per bit.
802.11a bit1=1
802.11b bit2=1
802.11g bit3=1"
::= { wlCapability 1 }
brpsWLanAvailableChannel OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available channel list."
::= { wlCapability 2 }
brpsWLanCapabilityEncryptModeCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { wlCapability 3 }
brpsWLanCapabilityEncryptModeTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsWLanCapabilityEncryptModeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { wlCapability 4 }
brpsWLanCapabilityEncryptModeEntry OBJECT-TYPE
SYNTAX BrpsWLanCapabilityEncryptModeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brpsWLanCapabilityEncryptModeIndex }
::= { brpsWLanCapabilityEncryptModeTable 1 }
BrpsWLanCapabilityEncryptModeEntry ::=
SEQUENCE {
brpsWLanCapabilityEncryptModeIndex
INTEGER,
brpsWLanCapabilityEncryptModeType
INTEGER,
brpsWLanCapabilityEncryptModeDescription
OCTET STRING,
brpsWLanCapabilityEncryptModeSupported
INTEGER
}
brpsWLanCapabilityEncryptModeIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { brpsWLanCapabilityEncryptModeEntry 1 }
brpsWLanCapabilityEncryptModeType OBJECT-TYPE
SYNTAX INTEGER {
none(1),
wep(2),
tkip(3),
aes(4),
ckip(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Encrypt Mode Type"
::= { brpsWLanCapabilityEncryptModeEntry 2 }
brpsWLanCapabilityEncryptModeDescription OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Encrypt Mode description"
::= { brpsWLanCapabilityEncryptModeEntry 3 }
brpsWLanCapabilityEncryptModeSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0: Not Supported
1: Supported"
::= { brpsWLanCapabilityEncryptModeEntry 4 }
brpsWLanCapabilityAuthModeCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { wlCapability 5 }
brpsWLanCapabilityAuthModeTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsWLanCapabilityAuthModeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { wlCapability 6 }
brpsWLanCapabilityAuthModeEntry OBJECT-TYPE
SYNTAX BrpsWLanCapabilityAuthModeEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brpsWLanCapabilitAuthModeIndex }
::= { brpsWLanCapabilityAuthModeTable 1 }
BrpsWLanCapabilityAuthModeEntry ::=
SEQUENCE {
brpsWLanCapabilitAuthModeIndex
INTEGER,
brpsWLanCapabilityAuthModeType
INTEGER,
brpsWLanCapabilityAuthModeDescription
OCTET STRING,
brpsWLanCapabilityAuthModeSupported
INTEGER
}
brpsWLanCapabilitAuthModeIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { brpsWLanCapabilityAuthModeEntry 1 }
brpsWLanCapabilityAuthModeType OBJECT-TYPE
SYNTAX INTEGER {
opensystem(1),
shardkey(2),
wpa-psk(3),
wpa-none(4),
wpa(5),
wpa2(6),
leap(7),
eapfast-none(8),
eapfast-mschapv2(9),
eapfast-gtc(10),
eapfast-tls(11),
wpa2-psk(12)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Auth Mode Type"
::= { brpsWLanCapabilityAuthModeEntry 2 }
brpsWLanCapabilityAuthModeDescription OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Auth Mode description"
::= { brpsWLanCapabilityAuthModeEntry 3 }
brpsWLanCapabilityAuthModeSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0: Not Supported
1: Supported"
::= { brpsWLanCapabilityAuthModeEntry 4 }
brpsWLanCapabilityAuthEAPCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { wlCapability 7 }
brpsWLanCapabilityAuthEAPTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsWLanCapabilityAuthEAPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { wlCapability 8 }
brpsWLanCapabilityAuthEAPEntry OBJECT-TYPE
SYNTAX BrpsWLanCapabilityAuthEAPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brpsWLanCapabilityAuthEAPIndex }
::= { brpsWLanCapabilityAuthEAPTable 1 }
BrpsWLanCapabilityAuthEAPEntry ::=
SEQUENCE {
brpsWLanCapabilityAuthEAPIndex
INTEGER,
brpsWLanCapabilityAuthEAPType
INTEGER,
brpsWLanCapabilityAuthEAPDescription
OCTET STRING,
brpsWLanCapabilityAuthEAPSupported
INTEGER,
brpsWLanCapabilityAuthEAPSupportAuthentication
INTEGER,
brpsWLanCapabilityAuthEAPSupportEncryption
INTEGER
}
brpsWLanCapabilityAuthEAPIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { brpsWLanCapabilityAuthEAPEntry 1 }
brpsWLanCapabilityAuthEAPType OBJECT-TYPE
SYNTAX INTEGER {
eap-md5(1),
eap-tls(2),
eap-ttls(3),
peap(4),
leap(5),
eapfast-none(6),
eapfast-mschapv2(7),
eapfast-gtc(8),
eapfast-tls(9)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Auth EAP Type"
::= { brpsWLanCapabilityAuthEAPEntry 2 }
brpsWLanCapabilityAuthEAPDescription OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Auth EAP description"
::= { brpsWLanCapabilityAuthEAPEntry 3 }
brpsWLanCapabilityAuthEAPSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0: Not Supported
1: Supported"
::= { brpsWLanCapabilityAuthEAPEntry 4 }
brpsWLanDestination OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The destination of this NIC."
::= { wlGeneralInfo 1 }
brpsWLanTransmitLevel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The level of the transmitting power."
::= { wlGeneralInfo 2 }
brpsPit3WLanTestStatus OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The test status of pit3 for WLAN."
::= { wlGeneralInfo 3 }
brpsWLanNetSearchSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Wireless network serch function is not supported.
1 indicates the Wireless network serch function is implemented by the firmware"
::= { wlNetSearch 1 }
brpsAvailableWLanScan OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Read: unsupported(1), supported(2)
Set: <Format>= <1:Start | 2:Start w/ option>[;<sWLanName>;<sWLanCommMode>[;<sWLanChannel>]]"
::= { wlNetSearch 2 }
brpsAvailableWLanScanWaitTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Scan Wait Time"
::= { wlNetSearch 3 }
brpsAvailableWLanCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Available wireless LAN count."
::= { wlNetSearch 10 }
brpsAvailableWLanTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsAvailableWLanEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents Available Wireless LAN Info."
::= { wlNetSearch 11 }
brpsAvailableWLanEntry OBJECT-TYPE
SYNTAX BrpsAvailableWLanEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the brpsAvailableWLanTable table. Rows cannot be created or deleted."
INDEX { brpsAvailableWLanIndex }
::= { brpsAvailableWLanTable 1 }
BrpsAvailableWLanEntry ::=
SEQUENCE {
brpsAvailableWLanIndex
INTEGER,
brpsAvailableWLanName
OCTET STRING,
brpsAvailableWLanMode
INTEGER,
brpsAvailableWLanCommMode
INTEGER,
brpsAvailableWLanChannel
INTEGER,
brpsAvailableWLanPowerLevel
INTEGER,
brpsAvailableWLanAuthMode
INTEGER,
brpsAvailableWLanEncryptMode
INTEGER
}
brpsAvailableWLanIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brpsAvailableWLanEntry 1 }
brpsAvailableWLanName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN name."
::= { brpsAvailableWLanEntry 2 }
brpsAvailableWLanMode OBJECT-TYPE
SYNTAX INTEGER {
dot11b-gAuto(1),
dot11b(2),
dot11g(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN mode."
::= { brpsAvailableWLanEntry 3 }
brpsAvailableWLanCommMode OBJECT-TYPE
SYNTAX INTEGER {
accesPoint(1),
adhoc-Wi-Fi(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN communication mode."
::= { brpsAvailableWLanEntry 4 }
brpsAvailableWLanChannel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN channel."
::= { brpsAvailableWLanEntry 5 }
brpsAvailableWLanPowerLevel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN power level."
::= { brpsAvailableWLanEntry 6 }
brpsAvailableWLanAuthMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
active(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN authentication mode."
::= { brpsAvailableWLanEntry 7 }
brpsAvailableWLanEncryptMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
active(2),
wep(3),
tkip(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The available wireless LAN encryption mode."
::= { brpsAvailableWLanEntry 8 }
brpsWLanAOSSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates AOSS is not supported.
1 indicates AOSS is supported."
::= { wlAOSS 1 }
brpsWLanAOSSIsRunnning OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"
"
::= { wlAOSS 2 }
brpsWLanSESSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates SES is not supported.
1 indicates SES is supported."
::= { wlSES 1 }
brpsWLanWPSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates WPS is not supported.
1 indicates WPS is supported."
::= { wlWPS 1 }
brpsWLanWPSResult OBJECT-TYPE
SYNTAX INTEGER (-1..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates WPS is successful.
1 indicates WPS is not successful.
-1 indicates WPS is being set up.
"
::= { wlWPS 2 }
brpsWLanAPSetupMode OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"AP setup mode status."
::= { wlGeneral 1 }
brpsWLanMode OBJECT-TYPE
SYNTAX INTEGER {
dot11b-gAuto(1),
dot11b(2),
dot11g(3),
dot11g-turbo(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN mode."
::= { wlGeneral 2 }
brpsWLanName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The SSID setting."
::= { wlGeneral 3 }
brpsWLanCommMode OBJECT-TYPE
SYNTAX INTEGER {
infrastructure(1),
ad-Hoc-WiFi(2),
ad-Hoc(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN communication mode."
::= { wlGeneral 4 }
brpsWLanChannel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN channel setting."
::= { wlGeneral 5 }
brpsWLanCtsMode OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
always(2),
none(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN CTS mode setting."
::= { wlAdvanced 1 }
brpsWLanCtsRate OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN CTS rate setting.
However, the unit is 1/10."
::= { wlAdvanced 2 }
brpsWLanCtsType OBJECT-TYPE
SYNTAX INTEGER {
only(1),
rts-cts(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN CTS type setting."
::= { wlAdvanced 3 }
brpsWLanRtsCtsThreshold OBJECT-TYPE
SYNTAX INTEGER (256..2346)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN RTS/CTS threshold setting."
::= { wlAdvanced 4 }
brpsWLanLengthThreshold OBJECT-TYPE
SYNTAX INTEGER (256..2346)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN length threshold setting."
::= { wlAdvanced 5 }
brpsWLanDataRetry OBJECT-TYPE
SYNTAX INTEGER (0..15)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN DATA retyr setting."
::= { wlAdvanced 6 }
brpsWLanTransmitPowerSetting OBJECT-TYPE
SYNTAX INTEGER {
full(1),
half(2),
quarter(3),
one-eighth(4),
minimum(5),
off(6)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN transmit power setting."
::= { wlAdvanced 7 }
brpsWLanDeviceType OBJECT-TYPE
SYNTAX INTEGER {
stationMode(1),
accessPointMode(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN operation mode setting."
::= { wlAdvanced 8 }
brpsWLanEncryptMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
wep(2),
tkip(3),
aes(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN encrypt mode."
::= { wlAssociate 1 }
brpsWLanAuthMode OBJECT-TYPE
SYNTAX INTEGER {
openSystem(1),
sharedKey(2),
wpa-psk(3),
wpa-none(4),
wpa(5),
wpa2(6),
leap(7),
eapfast-none(8),
eapfast-mschapv2(9),
eapfast-gtc(10),
eapfast-tls(11),
wpa2-psk(12)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN authenticate mode."
::= { wlAssociate 11 }
brpsWLanAuthEAP OBJECT-TYPE
SYNTAX INTEGER {
eapMD5(1),
eapTLS(2),
eapTTLS(3),
peap(4),
leap(5),
eapfast-none(6),
eapfast-mschapv2(7),
eapfast-gtc(8),
eapfast-tls(9)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN authenticate EAP."
::= { wlAssociate 12 }
brpsWLanAuthUserID OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN authenticate user ID."
::= { wlAssociate 13 }
brpsWLanAuthUserPass OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN authenticate user password."
::= { wlAssociate 14 }
brpsWLanAssociate OBJECT-TYPE
SYNTAX INTEGER {
update(1),
print(2),
test(3),
applyonly(4),
simplewizard(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Wireless LAN associate."
::= { wlAssociate 21 }
brpsWLanAssociateTestResult OBJECT-TYPE
SYNTAX INTEGER {
linkOK(1),
noSuchWLan(2),
invalidWLanNetKey(3),
invalidAuthUserID(4),
invalidAuthUserPass(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN associate test result.
0 indicates cleared."
::= { wlAssociate 22 }
brpsWLanAssociateResult OBJECT-TYPE
SYNTAX INTEGER {
linkOK(1),
noSuchWLan(2),
invalidWLanNetKey(3),
invalidAuthUserID(4),
invalidAuthUserPass(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN associate result.
0 indicates cleared."
::= { wlAssociate 23 }
brpsWLanAssociateTestSupported OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Wireless network Associate Test function
is not supported.
1 indicates the Wireless network Associate Test function
is implemented by the firmware"
::= { wlAssociate 24 }
brpsWLanWepKeyDefaultIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The value of brpsWLanWepKeyIndex corresponding to the default setting."
::= { wlWEP 1 }
brpsWLanWepKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrpsWLanWepKeyEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents WEP KEY Info."
::= { wlWEP 11 }
brpsWLanWepKeyEntry OBJECT-TYPE
SYNTAX BrpsWLanWepKeyEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the brpsWLanWepKeyTable table. Rows cannot be created or deleted."
INDEX { brpsWLanWepKeyIndex }
::= { brpsWLanWepKeyTable 1 }
BrpsWLanWepKeyEntry ::=
SEQUENCE {
brpsWLanWepKeyIndex
INTEGER,
brpsWLanWepKeySize
INTEGER,
brpsWLanWepKeyType
INTEGER,
brpsWLanWepKey
OCTET STRING
}
brpsWLanWepKeyIndex OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brpsWLanWepKeyEntry 1 }
brpsWLanWepKeySize OBJECT-TYPE
SYNTAX INTEGER {
size40(1),
size104(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The WEP KEY size."
::= { brpsWLanWepKeyEntry 2 }
brpsWLanWepKeyType OBJECT-TYPE
SYNTAX INTEGER {
hex(1),
ascii(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The WEP KEY type."
::= { brpsWLanWepKeyEntry 3 }
brpsWLanWepKey OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The WEP KEY."
::= { brpsWLanWepKeyEntry 4 }
brpsWLanNetworkKey OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The WPA-PSK."
::= { wlWPA 1 }
brpsWLanTKIPChangeInterval OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TKIP Interval (s)"
::= { wlTKIP 1 }
brpsWLanLEAPTimeout OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Leap timeout (s)"
::= { wlLEAP 1 }
brpsWLanOperatingMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The mode which is actually operating.
off(0),
dot11a(1),
dot11b(2),
dot11g(3)"
::= { wlGeneralStatus 1 }
brpsWLanRSSLevel OBJECT-TYPE
SYNTAX INTEGER (0..5)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN RSS Level."
::= { wlGeneralStatus 2 }
brpsWLanCommSpeed OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN communication speed.
However, the unit is 1/10."
::= { wlGeneralStatus 3 }
brpsWLanOperatingChannel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating channel."
::= { wlGeneralStatus 4 }
brpsWLanOperatingName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating SSID Name."
::= { wlGeneralStatus 5 }
brpsWLanOperatingCommMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating communication mode.
off(0),
infrastructure(1),
ad-Hoc-WiFi(2),
ad-Hoc(3)"
::= { wlGeneralStatus 6 }
brpsWLanOperatingEncryptMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating encrypt mode.
off(0),
none(1),
wep(2),
tkip(3),
aes(4),
ckip(5)"
::= { wlGeneralStatus 7 }
brpsWLanOperatingAuthMode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating authenticate mode.
off(0),
openSystem(1),
sharedKey(2),
wpa-psk(3),
wpa-none(4),
wpa(5),
wpa2(6),
leap(7),
eapfast-none(8),
eapfast-mschapv2(9),
eapfast-gtc(10),
eapfast-tls(11),
wpa2-psk(12)"
::= { wlGeneralStatus 8 }
brpsWLanOperatingWepKeyDefaultIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Wireless LAN operating WepKeyDefaultIndex."
::= { wlGeneralStatus 9 }
brMultiIFSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Multi Interface is not supported.
1 indicates Multi Interface is supported."
::= { brMultiIFconfig 1 }
brMultiIFActiveIF OBJECT-TYPE
SYNTAX INTEGER {
lan(1),
wirelesslan(2),
both(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"1 LAN
2 Wireless LAN
3 Both"
::= { brMultiIFconfig 2 }
brMultiIFAllSetDefault OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting the value resets all parameters to their factory default
value."
::= { brMultiIFconfig 3 }
brMultiIFCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"MultiIF Count"
::= { brMultiIFconfig 4 }
brMultiIFConfigureTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFConfigureEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFconfig 5 }
brMultiIFConfigureEntry OBJECT-TYPE
SYNTAX BrMultiIFConfigureEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFConfigureTable 1 }
BrMultiIFConfigureEntry ::=
SEQUENCE {
brMultiIFConfigureIndex
INTEGER,
brMultiIFType
INTEGER,
brMultiIFDescription
DisplayString,
brMultiIFNodeName
OCTET STRING,
brMultiIFInterfaceEnable
INTEGER,
brMultiIFEnetMode
INTEGER,
brMultiIFHardwareType
INTEGER,
brMultiIFNodeType
OCTET STRING,
brMultiIFInterfaceEnableImmediate
INTEGER
}
brMultiIFConfigureIndex OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brMultiIFConfigureEntry 1 }
brMultiIFType OBJECT-TYPE
SYNTAX INTEGER {
lan(1),
wirelesslan(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Interface Type"
::= { brMultiIFConfigureEntry 2 }
brMultiIFDescription OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Interface Description"
::= { brMultiIFConfigureEntry 3 }
brMultiIFNodeName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An administratively-assigned name for this
managed node. By convention, this is the node's
fully-qualified domain name."
::= { brMultiIFConfigureEntry 4 }
brMultiIFInterfaceEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the Interfase is not enabled.
1 indicates the Interfase is enabled."
::= { brMultiIFConfigureEntry 5 }
brMultiIFEnetMode OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Ethernet type."
::= { brMultiIFConfigureEntry 6 }
brMultiIFHardwareType OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Hardware type of the print server."
::= { brMultiIFConfigureEntry 7 }
brMultiIFNodeType OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual description of the entity. This value
should include the full name and version
identification of the system's hardware type,
software operating-system, and networking
software. It is mandatory that this only contain
printable ASCII characters."
::= { brMultiIFConfigureEntry 8 }
brMultiIFInterfaceEnableImmediate OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"
"
::= { brMultiIFConfigureEntry 9 }
brMultiIFPrimaryInterface OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary Interface"
::= { brMultiIFconfig 6 }
brMultiIFInterfaceInformation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0bit Auto
1bit manual
2bit enable both
3bit disable both"
::= { brMultiIFconfig 7 }
brMultiIFDNSTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFDNSEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFdns 1 }
brMultiIFDNSEntry OBJECT-TYPE
SYNTAX BrMultiIFDNSEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFDNSTable 1 }
BrMultiIFDNSEntry ::=
SEQUENCE {
brMultiIFTCPIPDNSIPSetup
INTEGER,
brMultiIFPrimaryDNSIPAddress
IpAddress,
brMultiIFSecondaryDNSIPAddress
IpAddress,
brMultiIFTCPIPConnectTime
INTEGER
}
brMultiIFTCPIPDNSIPSetup OBJECT-TYPE
SYNTAX INTEGER {
static(1),
auto(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"DNS mode
1:static
2:auto"
::= { brMultiIFDNSEntry 1 }
brMultiIFPrimaryDNSIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary DNS IP Address"
::= { brMultiIFDNSEntry 2 }
brMultiIFSecondaryDNSIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary DNS IP Address"
::= { brMultiIFDNSEntry 3 }
brMultiIFTCPIPConnectTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TCP/IP connect time."
::= { brMultiIFDNSEntry 4 }
brMultiIFControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFControlEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFcontrol 1 }
brMultiIFControlEntry OBJECT-TYPE
SYNTAX BrMultiIFControlEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFControlTable 1 }
BrMultiIFControlEntry ::=
SEQUENCE {
brMultiIFSetDefault
INTEGER
}
brMultiIFSetDefault OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting the value resets all parameters to their factory default
value."
::= { brMultiIFControlEntry 1 }
brMultiIFServiceTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFServiceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFservice 1 }
brMultiIFServiceEntry OBJECT-TYPE
SYNTAX BrMultiIFServiceEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFServiceTable 1 }
BrMultiIFServiceEntry ::=
SEQUENCE {
brMultiIFServiceCount
INTEGER,
brMultiIFServiceStringLimit
INTEGER,
brMultiIFServiceStringCount
INTEGER,
brMultiIFServiceFilterCount
INTEGER
}
brMultiIFServiceCount OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of services on this print server."
::= { brMultiIFServiceEntry 1 }
brMultiIFServiceStringLimit OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of service strings supported by the print server."
::= { brMultiIFServiceEntry 2 }
brMultiIFServiceStringCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of service strings currently defined on the print server."
::= { brMultiIFServiceEntry 3 }
brMultiIFServiceFilterCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of service filters implemented by the device."
::= { brMultiIFServiceEntry 4 }
brMultiIFServiceInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFServiceInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the attributes of a service."
::= { brMultiIFservice 2 }
brMultiIFServiceInfoEntry OBJECT-TYPE
SYNTAX BrMultiIFServiceInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the services table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brMultiIFConfigureIndex, brMultiIFServiceIndex }
::= { brMultiIFServiceInfoTable 1 }
BrMultiIFServiceInfoEntry ::=
SEQUENCE {
brMultiIFServiceIndex
INTEGER,
brMultiIFServiceName
DisplayString,
brMultiIFServicePort
INTEGER,
brMultiIFServiceFilter
INTEGER,
brMultiIFServiceBOT
INTEGER,
brMultiIFServiceEOT
INTEGER,
brMultiIFServiceMatch
INTEGER,
brMultiIFServiceReplace
INTEGER,
brMultiIFServiceTCPPort
INTEGER,
brMultiIFServiceNDSTree
DisplayString,
brMultiIFServiceNDSContext
OCTET STRING,
brMultiIFServiceVines
DisplayString,
brMultiIFServiceObsolete
INTEGER,
brMultiIFServiceNetwareServerCount
INTEGER,
brMultiIFServiceReceiveOnly
INTEGER,
brMultiIFServiceTCPQueued
INTEGER,
brMultiIFServiceProtocolLAT
INTEGER,
brMultiIFServiceProtocolTCPIP
INTEGER,
brMultiIFServiceProtocolNetware
INTEGER,
brMultiIFServiceProtocolAppleTalk
INTEGER,
brMultiIFServiceProtocolBanyan
INTEGER,
brMultiIFServiceProtocolDLC
INTEGER,
brMultiIFServiceProtocolNetBEUI
INTEGER,
brMultiIFServiceNetwareServerMode
INTEGER,
brMultiIFServiceNetwareRemotePrinterNum
INTEGER,
brMultiIFServiceProtocolIPP
INTEGER,
brMultiIFServiceAppleTalkType
DisplayString
}
brMultiIFServiceIndex OBJECT-TYPE
SYNTAX INTEGER (1..32)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The service number."
::= { brMultiIFServiceInfoEntry 1 }
brMultiIFServiceName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The service name."
::= { brMultiIFServiceInfoEntry 2 }
brMultiIFServicePort OBJECT-TYPE
SYNTAX INTEGER (0..31)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number assigned to this service."
::= { brMultiIFServiceInfoEntry 3 }
brMultiIFServiceFilter OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Filter number assigned to this service."
::= { brMultiIFServiceInfoEntry 4 }
brMultiIFServiceBOT OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Beginning of text string number assigned to this service."
::= { brMultiIFServiceInfoEntry 5 }
brMultiIFServiceEOT OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"End of text string number assigned to this service."
::= { brMultiIFServiceInfoEntry 6 }
brMultiIFServiceMatch OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Match string number assigned to this service."
::= { brMultiIFServiceInfoEntry 7 }
brMultiIFServiceReplace OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Replace string number assigned to this service."
::= { brMultiIFServiceInfoEntry 8 }
brMultiIFServiceTCPPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"TCP Port number assigned to this service."
::= { brMultiIFServiceInfoEntry 9 }
brMultiIFServiceNDSTree OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NDS Tree."
::= { brMultiIFServiceInfoEntry 10 }
brMultiIFServiceNDSContext OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NDS Context in Unicode."
::= { brMultiIFServiceInfoEntry 11 }
brMultiIFServiceVines OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..48) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Vines StreetTalk name for this service."
::= { brMultiIFServiceInfoEntry 12 }
brMultiIFServiceObsolete OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Obsolete parameter that is no longer used"
::= { brMultiIFServiceInfoEntry 13 }
brMultiIFServiceNetwareServerCount OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of Netware servers enabled on this service. Modifying the
value will truncate the server list to the specified number of servers. If the value set is greater than the number of servers currently on the list, then the list will be unchanged."
::= { brMultiIFServiceInfoEntry 14 }
brMultiIFServiceReceiveOnly OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the service will only receive data, any printer
responses will be discarded."
::= { brMultiIFServiceInfoEntry 15 }
brMultiIFServiceTCPQueued OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the raw TCP connections to the port will be
queued while waiting for the port to become available"
::= { brMultiIFServiceInfoEntry 16 }
brMultiIFServiceProtocolLAT OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the LAT protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 17 }
brMultiIFServiceProtocolTCPIP OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the TCP/IP protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 18 }
brMultiIFServiceProtocolNetware OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the Netware protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 19 }
brMultiIFServiceProtocolAppleTalk OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the AppleTalk protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 20 }
brMultiIFServiceProtocolBanyan OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the Banyan protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 21 }
brMultiIFServiceProtocolDLC OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the DLC protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 22 }
brMultiIFServiceProtocolNetBEUI OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the NetBEUI protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 23 }
brMultiIFServiceNetwareServerMode OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Netware mode for this service. 0 = Queue Server, 1 = Remote Printer"
::= { brMultiIFServiceInfoEntry 24 }
brMultiIFServiceNetwareRemotePrinterNum OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Remote Printer Number for this service"
::= { brMultiIFServiceInfoEntry 25 }
brMultiIFServiceProtocolIPP OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the IPP protocol will be available on this service."
::= { brMultiIFServiceInfoEntry 26 }
brMultiIFServiceAppleTalkType OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"AppleTalk type."
::= { brMultiIFServiceInfoEntry 27 }
brMultiIFServiceStringInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFServiceStringInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents the service BOT/EOT/MATCH/REPLACE strings defined."
::= { brMultiIFservice 3 }
brMultiIFServiceStringInfoEntry OBJECT-TYPE
SYNTAX BrMultiIFServiceStringInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the service string table. Rows cannot be created or deleted
via direct SNMP operations."
INDEX { brMultiIFConfigureIndex, brMultiIFServiceStringIndex }
::= { brMultiIFServiceStringInfoTable 1 }
BrMultiIFServiceStringInfoEntry ::=
SEQUENCE {
brMultiIFServiceStringIndex
INTEGER,
brMultiIFServiceString
DisplayString
}
brMultiIFServiceStringIndex OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The string number."
::= { brMultiIFServiceStringInfoEntry 1 }
brMultiIFServiceString OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The character string definition suitable for displaying."
::= { brMultiIFServiceStringInfoEntry 2 }
brMultiIFTCPIPTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFTCPIPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFtcpip 1 }
brMultiIFTCPIPEntry OBJECT-TYPE
SYNTAX BrMultiIFTCPIPEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFTCPIPTable 1 }
BrMultiIFTCPIPEntry ::=
SEQUENCE {
brMultiIFTCPIPAddress
IpAddress,
brMultiIFTCPIPSubnetMask
IpAddress,
brMultiIFTCPIPGateway
IpAddress,
brMultiIFTCPIPMethod
INTEGER,
brMultiIFTCPIPUpdate
OCTET STRING,
brMultiIFTCPIPTimeout
INTEGER,
brMultiIFTCPIPBootTries
INTEGER,
brMultiIFTCPIPRARPNoSubnet
INTEGER,
brMultiIFTCPIPRARPNoGateway
INTEGER,
brMultiIFTCPIPUseMethod
INTEGER,
brMultiIFTCPIPMethodServer
IpAddress
}
brMultiIFTCPIPAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IP Address assigned to the print server."
::= { brMultiIFTCPIPEntry 1 }
brMultiIFTCPIPSubnetMask OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Subnet mask assigned to the print server."
::= { brMultiIFTCPIPEntry 2 }
brMultiIFTCPIPGateway OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Gateway/Router address assigned to the print server"
::= { brMultiIFTCPIPEntry 3 }
brMultiIFTCPIPMethod OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method used to determine the IP Address. AUTO tries all protocols.
STATIC uses the configured address. DHCP, BOOTP, and RARP use only
that protocol."
::= { brMultiIFTCPIPEntry 4 }
brMultiIFTCPIPUpdate OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(6) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Hardware MAC address to be updated. This value is write only. Will
read back as zeros."
::= { brMultiIFTCPIPEntry 5 }
brMultiIFTCPIPTimeout OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Timeout used for LPD connections."
::= { brMultiIFTCPIPEntry 6 }
brMultiIFTCPIPBootTries OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of attempts to use BOOTP, RARP, and DHCP."
::= { brMultiIFTCPIPEntry 7 }
brMultiIFTCPIPRARPNoSubnet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If enabled, do not set the subnet mask based on the RARP response."
::= { brMultiIFTCPIPEntry 8 }
brMultiIFTCPIPRARPNoGateway OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If enabled, do not set the gateway/router address based on the RARP response."
::= { brMultiIFTCPIPEntry 9 }
brMultiIFTCPIPUseMethod OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method type that used set up TCP/IP configuration."
::= { brMultiIFTCPIPEntry 10 }
brMultiIFTCPIPMethodServer OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If TCP/IP configuration is setted up by any protocol server,
this entry indicates the IP address of the server."
::= { brMultiIFTCPIPEntry 11 }
brMultiIFNetBIOSTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFNetBIOSEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFnetbeui 1 }
brMultiIFNetBIOSEntry OBJECT-TYPE
SYNTAX BrMultiIFNetBIOSEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFNetBIOSTable 1 }
BrMultiIFNetBIOSEntry ::=
SEQUENCE {
brMultiIFNetBIOSIPMethod
INTEGER,
brMultiIFTCPIPNetBIOSPrimaryWINSAddr
IpAddress,
brMultiIFTCPIPNetBIOSSecondaryWINSAddr
IpAddress,
brMultiIFNetBEUIDomain
DisplayString
}
brMultiIFNetBIOSIPMethod OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Method used to determine the IP Address of the WINS server.
AUTO tries all protocols (currently only DHCP is tried).
STATIC uses the configured address."
::= { brMultiIFNetBIOSEntry 1 }
brMultiIFTCPIPNetBIOSPrimaryWINSAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the primary WINS server."
::= { brMultiIFNetBIOSEntry 2 }
brMultiIFTCPIPNetBIOSSecondaryWINSAddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The IP Address of the secondary WINS server."
::= { brMultiIFNetBIOSEntry 3 }
brMultiIFNetBEUIDomain OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..15) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The NetBEUI domain name."
::= { brMultiIFNetBIOSEntry 4 }
brMultiIFAPIPATable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFAPIPAEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalapipa 1 }
brMultiIFAPIPAEntry OBJECT-TYPE
SYNTAX BrMultiIFAPIPAEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFAPIPATable 1 }
BrMultiIFAPIPAEntry ::=
SEQUENCE {
brMultiIFAPIPASupported
INTEGER,
brMultiIFAPIPAEnable
INTEGER
}
brMultiIFAPIPASupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the APIPA protocol is not supported.
1 indicates APIPA support is implemented by the firmware"
::= { brMultiIFAPIPAEntry 1 }
brMultiIFAPIPAEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the APIPA protocol is not enabled.
1 indicates that the APIPA protocol is enabled.
Writing a non-zero value will enable the APIPA
protocol if it is supported by the firmware."
::= { brMultiIFAPIPAEntry 2 }
brMultiIFLAATable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFLAAEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalLAA 1 }
brMultiIFLAAEntry OBJECT-TYPE
SYNTAX BrMultiIFLAAEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFLAATable 1 }
BrMultiIFLAAEntry ::=
SEQUENCE {
brMultiIFLAASupported
INTEGER,
brMultiIFLAAMacAddress
OCTET STRING
}
brMultiIFLAASupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value indicate if the locally administered addressing is supported.
0: Not Supported
1: Supported"
::= { brMultiIFLAAEntry 1 }
brMultiIFLAAMacAddress OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(6) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A locally administered address (LAA) that replaces the factory-assigned MAC address (UAA: universally administered address).
If this setting is all-zero address (i.e. 6 bytes of zeros), the
factory-assigned
MAC address is used as the MAC address of the device.
The LAA address must start with X2, X6, XA, or XE, where X is any
hexadecimal digit 0 to F."
::= { brMultiIFLAAEntry 2 }
brMultiIFIPv6AddressCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFIPv6AddressCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalIPv6 1 }
brMultiIFIPv6AddressCountEntry OBJECT-TYPE
SYNTAX BrMultiIFIPv6AddressCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFIPv6AddressCountTable 1 }
BrMultiIFIPv6AddressCountEntry ::=
SEQUENCE {
brMultiIFIPv6AddressCount
INTEGER
}
brMultiIFIPv6AddressCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IPv6Address Counter."
::= { brMultiIFIPv6AddressCountEntry 1 }
brMultiIFIPv6AddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFIPv6AddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalIPv6 2 }
brMultiIFIPv6AddressEntry OBJECT-TYPE
SYNTAX BrMultiIFIPv6AddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex, brMultiIFIPv6AddressIndex }
::= { brMultiIFIPv6AddressTable 1 }
BrMultiIFIPv6AddressEntry ::=
SEQUENCE {
brMultiIFIPv6AddressIndex
INTEGER,
brMultiIFIPv6Address
Ipv6Address,
brMultiIFIPv6UseMethod
INTEGER,
brMultiIFIPv6MethodServer
DisplayString
}
brMultiIFIPv6AddressIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { brMultiIFIPv6AddressEntry 1 }
brMultiIFIPv6Address OBJECT-TYPE
SYNTAX Ipv6Address
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFIPv6AddressEntry 2 }
brMultiIFIPv6UseMethod OBJECT-TYPE
SYNTAX INTEGER (0..7)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Method type that used set up TCP/IP configuration.
0: Unknown (Information not supported)
1: Manually
2: DHCPv6
3: Stateless Address Auto-configuration
4: Reserved
5: Link Local"
::= { brMultiIFIPv6AddressEntry 3 }
brMultiIFIPv6MethodServer OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If TCP/IP configuration is setted up by any protocol server,
this entry indicates the IP address of the server."
::= { brMultiIFIPv6AddressEntry 4 }
brMultiIFIPv6StaticAddressCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFIPv6StaticAddressCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalIPv6 3 }
brMultiIFIPv6StaticAddressCountEntry OBJECT-TYPE
SYNTAX BrMultiIFIPv6StaticAddressCountEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFIPv6StaticAddressCountTable 1 }
BrMultiIFIPv6StaticAddressCountEntry ::=
SEQUENCE {
brMultiIFIPv6StaticAddressCount
INTEGER
}
brMultiIFIPv6StaticAddressCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"IPv6StaticAddress Counter."
::= { brMultiIFIPv6StaticAddressCountEntry 1 }
brMultiIFIPv6StaticAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFIPv6StaticAddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalIPv6 4 }
brMultiIFIPv6StaticAddressEntry OBJECT-TYPE
SYNTAX BrMultiIFIPv6StaticAddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex, brMultiIFIPv6StaticAddressIndex }
::= { brMultiIFIPv6StaticAddressTable 1 }
BrMultiIFIPv6StaticAddressEntry ::=
SEQUENCE {
brMultiIFIPv6StaticAddressIndex
INTEGER,
brMultiIFIPv6StaticAddressEnable
INTEGER,
brMultiIFIPv6StaticAddress
Ipv6Address,
brMultiIFIPv6StaticAddressPrefixLength
INTEGER
}
brMultiIFIPv6StaticAddressIndex OBJECT-TYPE
SYNTAX INTEGER (1..16)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"index"
::= { brMultiIFIPv6StaticAddressEntry 1 }
brMultiIFIPv6StaticAddressEnable OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"index"
::= { brMultiIFIPv6StaticAddressEntry 2 }
brMultiIFIPv6StaticAddress OBJECT-TYPE
SYNTAX Ipv6Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IPv6 Static Address"
::= { brMultiIFIPv6StaticAddressEntry 3 }
brMultiIFIPv6StaticAddressPrefixLength OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"IPv6Address Prefix Length"
::= { brMultiIFIPv6StaticAddressEntry 4 }
brMultiIFDNSIPv6AddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFDNSIPv6AddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalIPv6 5 }
brMultiIFDNSIPv6AddressEntry OBJECT-TYPE
SYNTAX BrMultiIFDNSIPv6AddressEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFDNSIPv6AddressTable 1 }
BrMultiIFDNSIPv6AddressEntry ::=
SEQUENCE {
brMultiIFPrimaryDNSIPv6Address
Ipv6Address,
brMultiIFSecondaryDNSIPv6Address
Ipv6Address
}
brMultiIFPrimaryDNSIPv6Address OBJECT-TYPE
SYNTAX Ipv6Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Primary DNS IPv6 Address"
::= { brMultiIFDNSIPv6AddressEntry 1 }
brMultiIFSecondaryDNSIPv6Address OBJECT-TYPE
SYNTAX Ipv6Address
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Secondary DNS IPv6 Address"
::= { brMultiIFDNSIPv6AddressEntry 2 }
brMultiIFWebServicesTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrMultiIFWebServicesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { brMultiIForiginalWebServices 1 }
brMultiIFWebServicesEntry OBJECT-TYPE
SYNTAX BrMultiIFWebServicesEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brMultiIFConfigureIndex }
::= { brMultiIFWebServicesTable 1 }
BrMultiIFWebServicesEntry ::=
SEQUENCE {
brMultiIFWebServicesName
DisplayString,
brMultiIFWebServicesInstanceID
INTEGER,
brMultiIFWebServicesMetadataVersion
INTEGER
}
brMultiIFWebServicesName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFWebServicesEntry 1 }
brMultiIFWebServicesInstanceID OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFWebServicesEntry 2 }
brMultiIFWebServicesMetadataVersion OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { brMultiIFWebServicesEntry 3 }
brLdapSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the LDAP client is not supported.
1 indicates the LDAP client is implemented by the firmware"
::= { broriginalldap 1 }
brLdapEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the LDAP client is not enabled.
1 indicates that the LDAP client is enabled.
Writing a non-zero value will enable the Ldap
if it is supported by the firmware."
::= { broriginalldap 2 }
brLdapTimeout OBJECT-TYPE
SYNTAX INTEGER (1..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"timeout value (sec) for LDAP server."
::= { broriginalldap 3 }
brLdapTimeoutSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the LDAP timeout is not supported.
1 indicates the LDAP timeout is implemented by the firmware"
::= { broriginalldap 4 }
brLdapServerCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of LDAP Server INDEX."
::= { broriginalldap 11 }
brLdapServerInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrLdapServerInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents LDAP Server Info."
::= { broriginalldap 12 }
brLdapServerInfoEntry OBJECT-TYPE
SYNTAX BrLdapServerInfoEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the LdapServerInfo table. Rows cannot be created or deleted."
INDEX { brLdapServerInfoIndex }
::= { brLdapServerInfoTable 1 }
BrLdapServerInfoEntry ::=
SEQUENCE {
brLdapServerInfoIndex
INTEGER,
brLdapServerName
DisplayString,
brLdapServerPort
INTEGER,
brLdapServerAuth
INTEGER,
brLdapServerUserDN
OCTET STRING,
brLdapServerPassword
OCTET STRING,
brLdapServerPasswordSet
INTEGER,
brLdapServerBaseDN
OCTET STRING,
brLdapServerAttrEMail
DisplayString,
brLdapServerAttrFAXNumber
DisplayString,
brLdapServerAttrDetail1
DisplayString,
brLdapServerAttrDetail2
DisplayString,
brLdapServerAttrDetail3
DisplayString,
brLdapServerAttrDetail4
DisplayString,
brLdapServerAttrDetailEnable1
INTEGER,
brLdapServerAttrDetailEnable2
INTEGER,
brLdapServerAttrDetailEnable3
INTEGER,
brLdapServerAttrDetailEnable4
INTEGER,
brLdapKerberosServerName
DisplayString,
brLdapKerberosServerPort
INTEGER
}
brLdapServerInfoIndex OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brLdapServerInfoEntry 1 }
brLdapServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server name."
::= { brLdapServerInfoEntry 2 }
brLdapServerPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server port number."
::= { brLdapServerInfoEntry 3 }
brLdapServerAuth OBJECT-TYPE
SYNTAX INTEGER {
anonymous(1),
simple(2),
kerberos(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server authentication method."
::= { brLdapServerInfoEntry 4 }
brLdapServerUserDN OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server user DN."
::= { brLdapServerInfoEntry 5 }
brLdapServerPassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server password."
::= { brLdapServerInfoEntry 6 }
brLdapServerPasswordSet OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Returns 1 if the LDAP server password is set, 0 if not set."
::= { brLdapServerInfoEntry 7 }
brLdapServerBaseDN OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server base DN."
::= { brLdapServerInfoEntry 8 }
brLdapServerAttrEMail OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or e-mail."
::= { brLdapServerInfoEntry 10 }
brLdapServerAttrFAXNumber OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or facsimile telephone number."
::= { brLdapServerInfoEntry 11 }
brLdapServerAttrDetail1 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or detail 1."
::= { brLdapServerInfoEntry 12 }
brLdapServerAttrDetail2 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or detail 2."
::= { brLdapServerInfoEntry 13 }
brLdapServerAttrDetail3 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or detail 3."
::= { brLdapServerInfoEntry 14 }
brLdapServerAttrDetail4 OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute or detail 4."
::= { brLdapServerInfoEntry 15 }
brLdapServerAttrDetailEnable1 OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable flag of the LDAP server attribute of detail 1."
::= { brLdapServerInfoEntry 16 }
brLdapServerAttrDetailEnable2 OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable flag of the LDAP server attribute of detail 2."
::= { brLdapServerInfoEntry 17 }
brLdapServerAttrDetailEnable3 OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable flag of the LDAP server attribute of detail 3."
::= { brLdapServerInfoEntry 18 }
brLdapServerAttrDetailEnable4 OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Enable flag of the LDAP server attribute of detail 4."
::= { brLdapServerInfoEntry 19 }
brLdapServerAttrNameCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Maximum number of LDAP Server Attribute of name INDEX."
::= { broriginalldap 21 }
brLdapServerAttrNameTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrLdapServerAttrNameEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents LDAP Server Attribute of name."
::= { broriginalldap 22 }
brLdapServerAttrNameEntry OBJECT-TYPE
SYNTAX BrLdapServerAttrNameEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the LdapServerAttributeName table. Rows cannot be created or deleted."
INDEX { brLdapServerInfoIndex, brLdapServerAttrNameIndex }
::= { brLdapServerAttrNameTable 1 }
BrLdapServerAttrNameEntry ::=
SEQUENCE {
brLdapServerAttrNameIndex
INTEGER,
brLdapServerAttrName
DisplayString
}
brLdapServerAttrNameIndex OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brLdapServerAttrNameEntry 1 }
brLdapServerAttrName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The LDAP server attribute of name."
::= { brLdapServerAttrNameEntry 2 }
brLdapSetDefault OBJECT-TYPE
SYNTAX INTEGER (0..32767)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting the value resets all LDAP parameters to their factory default
value."
::= { broriginalldap 99 }
brFuncLockSettingInit OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Init Function Lock Setting."
::= { funclock 1 }
brFuncLockAdminPassword OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get or Set the administrator password of Function Lock."
::= { funclock 2 }
brFuncLock OBJECT-TYPE
SYNTAX INTEGER (1..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get or Set the status of Function Lock."
::= { funclock 3 }
brFuncLockPublicFuncCount OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the number of functions to be locked on the public mode."
::= { funclock 4 }
brFuncLockUserCount OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the number of users to be locked on function lock."
::= { funclock 6 }
brFuncLockUserTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFuncLockUserEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { funclock 7 }
brFuncLockPublicTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFuncLockPublicEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { funclock 5 }
brFuncLockPublicEntry OBJECT-TYPE
SYNTAX BrFuncLockPublicEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brFuncLockPublicFuncIndex }
::= { brFuncLockPublicTable 1 }
BrFuncLockPublicEntry ::=
SEQUENCE {
brFuncLockPublicFuncIndex
INTEGER,
brFuncLockPublicFuncMember
INTEGER,
brFuncLockPublicFuncSupported
INTEGER,
brFuncLockPublicFuncEnable
INTEGER
}
brFuncLockUserEntry OBJECT-TYPE
SYNTAX BrFuncLockUserEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brFuncLockUserIndex }
::= { brFuncLockUserTable 1 }
BrFuncLockUserEntry ::=
SEQUENCE {
brFuncLockUserIndex
INTEGER,
brFuncLockUserName
DisplayString,
brFuncLockUserPassword
DisplayString
}
brFuncLockPublicFuncIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the index value of functions to be locked on the public mode."
::= { brFuncLockPublicEntry 1 }
brFuncLockPublicFuncMember OBJECT-TYPE
SYNTAX INTEGER {
copycolor(1),
copybr(2),
faxtx(3),
faxrx(4),
scan(5),
print(6),
pcc(7)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the member of functions to be locked on the public mode."
::= { brFuncLockPublicEntry 2 }
brFuncLockPublicFuncSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the status of availableness of functions to be locked on the public mode."
::= { brFuncLockPublicEntry 3 }
brFuncLockPublicFuncEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get of Set the status of functions on the public mode."
::= { brFuncLockPublicEntry 4 }
brFuncLockUserIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the index value of users to be locked on function lock."
::= { brFuncLockUserEntry 1 }
brFuncLockUserName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get or Set the user name of function lock."
::= { brFuncLockUserEntry 2 }
brFuncLockUserPassword OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get or Set the user password of function lock."
::= { brFuncLockUserEntry 3 }
brFuncLockUserFuncCount OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the number of users to be locked on the function lock."
::= { funclock 8 }
brFuncLockUserFuncTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFuncLockUserFuncEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { funclock 9 }
brFuncLockUserFuncEntry OBJECT-TYPE
SYNTAX BrFuncLockUserFuncEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brFuncLockUserIndex, brFuncLockUserFuncIndex }
::= { brFuncLockUserFuncTable 1 }
BrFuncLockUserFuncEntry ::=
SEQUENCE {
brFuncLockUserFuncIndex
INTEGER,
brFuncLockUserFuncMember
INTEGER,
brFuncLockUserFuncSupported
INTEGER,
brFuncLockUserFuncEnable
INTEGER
}
brFuncLockUserFuncIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the index value of users to be locked on user mode."
::= { brFuncLockUserFuncEntry 1 }
brFuncLockUserFuncMember OBJECT-TYPE
SYNTAX INTEGER {
copycolor(1),
copybr(2),
faxtx(3),
faxrx(4),
scan(5),
print(6),
pcc(7)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the function numbers to be locked on user mode."
::= { brFuncLockUserFuncEntry 2 }
brFuncLockUserFuncSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Return the availableness of function to be locked on user mode."
::= { brFuncLockUserFuncEntry 3 }
brFuncLockUserFuncEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Get or Set the lock status on the user mode."
::= { brFuncLockUserFuncEntry 4 }
brFuncLockSetting OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Write the all information of function lock."
::= { funclock 10 }
brNetRemoteSetUpFileFormat OBJECT-TYPE
SYNTAX INTEGER {
rms(1),
rmd(2),
rmsrmd(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"It is a file format of the Net Remote Setup function."
::= { mcgRemoteSetup 3 }
brInfoAlertVersion OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"It indicates the version that prtAlertLocation is implemented correctly."
::= { printerinfomation 25 }
brInfoBlackPrint OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"It indicates black only print enable/disable info
0: disable
1: enable"
::= { printerinfomation 26 }
brpsWLanCapabilityAuthEAPSupportAuthentication OBJECT-TYPE
SYNTAX INTEGER (0..15)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"put supported authentication protocol as bit.
1bit:802.1X
2bit:WPA
3bit:WPA2
4bit:CCKM"
::= { brpsWLanCapabilityAuthEAPEntry 5 }
brpsWLanCapabilityAuthEAPSupportEncryption OBJECT-TYPE
SYNTAX INTEGER (0..15)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"put supported encryption as bit.
1bit:WEP
2bit:CKIP
3bit:TKIP
4bit:AES"
::= { brpsWLanCapabilityAuthEAPEntry 6 }
brLdapKerberosServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Kerberos server name for LDAP."
::= { brLdapServerInfoEntry 20 }
brLdapKerberosServerPort OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Kerberos server port number for LDAP."
::= { brLdapServerInfoEntry 21 }
brKerberosSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the Kerberos protocol is not supported.
1 indicates Kerberos support is implemented by the firmware"
::= { broriginalKerberos 1 }
brCIFSSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the CIFS protocol is not supported.
1 indicates CIFS support is implemented by the firmware"
::= { broriginalCIFS 1 }
brCIFSEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the CIFS protocol is not enabled.
1 indicates that the CIFS protocol is enabled.
Writing a non-zero value will enable the CIFS
protocol if it is supported by the firmware."
::= { broriginalCIFS 2 }
brSNMPV3Supported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates SNMPv3 is not supported.
1 indicates SNMPv3 is supported."
::= { broriginalSNMP 10 }
brSNMPCommMode OBJECT-TYPE
SYNTAX INTEGER (1..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"1 indicates v1/v2c read-write access is enable.
2 indicates v3 read-write access is enable.
3 indicates v1/v2c read-only access and v3 read-write access is enable."
::= { broriginalSNMP 11 }
brSNMPV3UserName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The username of SNMPv3."
::= { broriginalSNMP 12 }
brSNMPV3KeyType OBJECT-TYPE
SYNTAX INTEGER (1..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"1 indicates that the key type of SNMPv3 is ASCII.
2 indicates that the key type of SNMPv3 is HEX"
::= { broriginalSNMP 13 }
brSNMPV3AuthKey OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..16) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The authentication key of SNMPv3."
::= { broriginalSNMP 14 }
brSNMPV3AuthPassword OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..16) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The authentication password of SNMPv3."
::= { broriginalSNMP 15 }
brSNMPV3PrivKey OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..16) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The privacy key of SNMPv3."
::= { broriginalSNMP 16 }
brSNMPV3PrivPassword OBJECT-TYPE
SYNTAX DisplayString ( SIZE(1..16) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The privacy password of SNMPv3."
::= { broriginalSNMP 17 }
brSNMPV3ContextName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..32) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The contextname of SNMPv3."
::= { broriginalSNMP 18 }
brSNTPCSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"0 indicates the SNTP is not supported.
1 indicates SNTP is supported."
::= { broriginalSNTP 1 }
brSNTPCEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"0 indicates the SNTP is not disabled.
1 indicates that the SNTP is enabled.
"
::= { broriginalSNTP 2 }
brSNTPCSyncMethod OBJECT-TYPE
SYNTAX INTEGER (1..2)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"1 indicates Synchronous Method is AUTO.
2 indicates Synchronous Method is STATIC.
"
::= { broriginalSNTP 4 }
brSNTPCIntervalMin OBJECT-TYPE
SYNTAX INTEGER (1..168)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The minimum value of synchronous interval."
::= { broriginalSNTP 5 }
brSNTPCInterval OBJECT-TYPE
SYNTAX INTEGER (1..168)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The synchronous interval is used for synchronous method INTERVAL."
::= { broriginalSNTP 6 }
brSNTPCSyncResult OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The result of the last checking time.
1: Success
2: Synchronizing
3: Failed
4: Not yet checking"
::= { broriginalSNTP 7 }
brSNTPCPrimaryServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The primary server name of SNTP."
::= { broriginalSNTP 8 }
brSNTPCPrimaryServerPort OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number of primary SNTP server."
::= { broriginalSNTP 9 }
brSNTPCSecondaryServerName OBJECT-TYPE
SYNTAX DisplayString ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The secondary server name of SNTP."
::= { broriginalSNTP 10 }
brSNTPCSecondaryServerPort OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The port number of secondary SNTP server."
::= { broriginalSNTP 11 }
brSNTPCServerMethod OBJECT-TYPE
SYNTAX INTEGER (1..3)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"1 indicates SNTP Server Method is AUTO.
2 indicates SNTP Server Method is STATIC.
3 indicates SNTP Server Method is PRESET.
"
::= { broriginalSNTP 3 }
brPJLInfoFirmwareUpdateconfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrPJLInfoFirmwareUpdateconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table represents PJLInfoFirmwareUpdateconfig."
::= { pjlinfo 6 }
brPJLInfoFirmwareUpdateconfigEntry OBJECT-TYPE
SYNTAX BrPJLInfoFirmwareUpdateconfigEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the PJLInfoFirmwareUpdateconfig table. Rows cannot be created or deleted."
INDEX { brPJLInfoFirmwareUpdateconfigIndex }
::= { brPJLInfoFirmwareUpdateconfigTable 1 }
BrPJLInfoFirmwareUpdateconfigEntry ::=
SEQUENCE {
brPJLInfoFirmwareUpdateconfigIndex
INTEGER,
brPJLInfoFirmwareUpdateconfig
OCTET STRING
}
brPJLInfoFirmwareUpdateconfigIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number."
::= { brPJLInfoFirmwareUpdateconfigEntry 1 }
brPJLInfoFirmwareUpdateconfig OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The PJLInfoFirmwareUpdateconfig."
::= { brPJLInfoFirmwareUpdateconfigEntry 2 }
brFirmwareUpdateKeywordCount OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of Firmware for update the device."
::= { firmwareupdatekeyword 1 }
brFirmwareUpdateKeywordTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFirmwareUpdateKeywordEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table represents the number of Firmware for Update."
::= { firmwareupdatekeyword 2 }
brFirmwareUpdateKeywordEntry OBJECT-TYPE
SYNTAX BrFirmwareUpdateKeywordEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A row in the FirmwareUpdateKeyword table. Rows cannot be created or deleted."
INDEX { brFirmwareUpdateKeywordIndex }
::= { brFirmwareUpdateKeywordTable 1 }
BrFirmwareUpdateKeywordEntry ::=
SEQUENCE {
brFirmwareUpdateKeywordIndex
INTEGER,
brFirmwareUpdateKeyword
OCTET STRING
}
brFirmwareUpdateKeywordIndex OBJECT-TYPE
SYNTAX INTEGER (0..4)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brFirmwareUpdateKeywordEntry 1 }
brFirmwareUpdateKeyword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..255) )
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The keyword for firemware update the device."
::= { brFirmwareUpdateKeywordEntry 2 }
brFuncLockUserPrintPageCounterReset OBJECT-TYPE
SYNTAX INTEGER (0..0)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Reset all user's counter of Color/Mono print page."
::= { funclock 20 }
brFuncLockPublicPrintLimitEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This MIB represents Enable/Disable of print limit setting for public user."
::= { funclock 21 }
brFuncLockPublicPrintPageMax OBJECT-TYPE
SYNTAX INTEGER (1..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Maximum of print limited for public user."
::= { funclock 22 }
brFuncLockUserPrintPageTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFuncLockUserPrintPageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { funclock 25 }
brFuncLockUserPrintPageEntry OBJECT-TYPE
SYNTAX BrFuncLockUserPrintPageEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brFuncLockUserPrintPageIndex }
::= { brFuncLockUserPrintPageTable 1 }
BrFuncLockUserPrintPageEntry ::=
SEQUENCE {
brFuncLockUserPrintPageCountMono
INTEGER,
brFuncLockUserPrintPageCountColor
INTEGER,
brFuncLockUserPrintPageIndex
INTEGER,
brFuncLockUserPrintPageLimitEnable
INTEGER,
brFuncLockUserPrintPageMax
INTEGER,
brFuncLockUserPrintPageCountMonoLast
INTEGER,
brFuncLockUserPrintPageCountColorLast
INTEGER
}
brFuncLockUserPrintPageCountMono OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Counter of Monochrome Print Page for user."
::= { brFuncLockUserPrintPageEntry 3 }
brFuncLockUserPrintPageCountColor OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The counter of color print page for user."
::= { brFuncLockUserPrintPageEntry 4 }
brFuncLockPublicPrintPageCountColor OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The counter of color print page for public user."
::= { funclock 24 }
brFuncLockPcLoginNameAuthEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This MIB represents Enable/Disable of PC Login Authentication setting."
::= { funclock 26 }
brFuncLockPcLoginNameAuthCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of PC Login Name."
::= { funclock 27 }
brFuncLockPcLoginNameTable OBJECT-TYPE
SYNTAX SEQUENCE OF BrFuncLockPcLoginNameEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { funclock 28 }
brFuncLockPcLoginNameEntry OBJECT-TYPE
SYNTAX BrFuncLockPcLoginNameEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { brFuncLockPcLoginNameAuthIndex }
::= { brFuncLockPcLoginNameTable 1 }
BrFuncLockPcLoginNameEntry ::=
SEQUENCE {
brFuncLockPcLoginNameAuthIndex
INTEGER,
brFuncLockPcLoginName
OCTET STRING,
brFuncLockPcLoginNameAuthID
INTEGER
}
brFuncLockPcLoginNameAuthIndex OBJECT-TYPE
SYNTAX INTEGER (1..50)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brFuncLockPcLoginNameEntry 1 }
brFuncLockPcLoginName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The PC Login Name."
::= { brFuncLockPcLoginNameEntry 2 }
brFuncLockPcLoginNameAuthID OBJECT-TYPE
SYNTAX INTEGER (1..25)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"PC Login ID for PC Login name."
::= { brFuncLockPcLoginNameEntry 3 }
brFuncLockPublicPrintPageCountMono OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The counter of monochrome print page."
::= { funclock 23 }
brFuncLockUserPrintPageIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brFuncLockUserPrintPageEntry 1 }
brFuncLockUserPrintPageLimitEnable OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Maximum of Print Page setting for user."
::= { brFuncLockUserPrintPageEntry 2 }
brFuncLockUserPrintPageMax OBJECT-TYPE
SYNTAX INTEGER (1..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Maximum of print limited for user."
::= { brFuncLockUserPrintPageEntry 5 }
brFuncLockPublicPrintPageCountMonoLast OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { funclock 29 }
brFuncLockPublicPrintPageCountColorLast OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { funclock 30 }
brFuncLockUserPrintPageCountMonoLast OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brFuncLockUserPrintPageEntry 6 }
brFuncLockUserPrintPageCountColorLast OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
""
::= { brFuncLockUserPrintPageEntry 7 }
brFuncLockAutoCountResetFrequency OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { autocountreset 1 }
brFuncLockAutoCountResetTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(2..2) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { autocountreset 2 }
brFuncLockAutoCountResetWeek OBJECT-TYPE
SYNTAX INTEGER (1..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { autocountreset 3 }
brFuncLockAutoCountResetDate OBJECT-TYPE
SYNTAX INTEGER (1..31)
ACCESS read-write
STATUS mandatory
DESCRIPTION
""
::= { autocountreset 4 }
brWlanSimpleWizardSupported OBJECT-TYPE
SYNTAX INTEGER (0..1)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"WLAN Simple Wizard support information.
0 indicates Simple Wizard is not supported.
1 indicates Simple Wizard is supported."
::= { wlSimpleWizard 1 }
brWlanSimpleWizardPassword OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE(0..64) )
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Simple Wizard Password.
Max size 64"
::= { wlSimpleWizard 2 }
END