mibs/MIBS/dlink/DLINKSW-CPU-PROTECT-MIB

485 lines
17 KiB
Plaintext
Raw Normal View History

2023-12-05 12:25:34 +01:00
-- *****************************************************************
-- DLINKSW-CPU-PROTECT-MIB.mib : CPU Protection MIB
--
-- Copyright (c) 2012 D-Link Corporation, all rights reserved.
--
-- *****************************************************************
DLINKSW-CPU-PROTECT-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-GROUP, MODULE-COMPLIANCE
FROM SNMPv2-CONF
Integer32, Counter64, OBJECT-TYPE, MODULE-IDENTITY
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC
dlinkIndustrialCommon
FROM DLINK-ID-REC-MIB;
dlinkSwCpuProtectMIB MODULE-IDENTITY
LAST-UPDATED "201208080000Z"
ORGANIZATION "D-Link Corp."
CONTACT-INFO
" D-Link Corporation
Postal: No. 289, Sinhu 3rd Rd., Neihu District,
Taipei City 114, Taiwan, R.O.C
Tel: +886-2-66000123
E-mail: tsd@dlink.com.tw
"
DESCRIPTION
"The MIB module for managing CPU protection."
REVISION "201208080000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { dlinkIndustrialCommon 19 }
--
-- Textual conventions
--
CpuProtectProtocolType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents a protocol type.
Note that a particular agent may support only certain protocol
types. Thus, the valid values of this object are project
dependent.
An agent may respond with an error (e.g., 'inconsistentValue ')
to a management SET operation which attempts to modify
the value to one which is not supported by the managed device.
arp(1) indicates IP Address Resolution Protocol (ARP).
bgp(2) indicates Border Gateway Protocol.
dhcp(3) indicates Dynamic Host Configuration Protocol.
dhcpv6(4) indicates Dynamic Host Configuration Protocol for IPv6.
dns(5) indicates Domain Name Services.
dot1x(6) indicates IEEE 802.1X (Port Based Network Access Control).
dvmrp(7) indicates Distance Vector Multicast Routing Protocol.
gvrp(8) indicates GARP VLAN Registration Protocol.
icmp(9) indicates IPv4 Internet Control Message Protocol.
icmpv6Ndp(10) indicates IPv6 ICMP Neighbor Discover Protocol (NS/NA/RS/RA).
icmpv6Other(11) indicates IPv6 ICMP except NDP NS/NA/RS/RA.
igmp(12) indicates Internet Group Management Protocol.
lacp(13), indicates Link Aggregation Control Protocol.
ntp(14), indicates Network Time Protocol.
ospf(15), indicates Open Shortest Path First.
ospfv3(16), indicates OSPF for IPv6.
pim(17), indicates Protocol Independent Multicast.
pppoe(18), indicates Point-to-Point Protocol over Ethernet.
rip(19), indicates Routing Information Protocol.
ripng(20), indicates Routing Information Protocol for IPv6.
snmp(21), indicates Simple Network Management Protocol.
ssh(22), indicates Secured shell.
stp(23), indicates Spanning Tree Protocol (IEEE 802.1D).
telnet(24), indicates Telnet.
tftp(25), indicates Trivial File Transfer Protocol.
vrrp(26), indicates Virtual Router Redundancy Protocol.
web(27) indicates HTTP and HTTPS.
"
SYNTAX INTEGER
{
arp(1),
bgp(2),
dhcp(3),
dhcpv6(4),
dns(5),
dot1x(6),
dvmrp(7),
gvrp(8),
icmp(9),
icmpv6Ndp(10),
icmpv6Other(11),
igmp(12),
lacp(13),
ntp(14),
ospf(15),
ospfv3(16),
pim(17),
pppoe(18),
rip(19),
ripng(20),
snmp(21),
ssh(22),
stp(23),
telnet(24),
tftp(25),
vrrp(26),
web(27)
}
MaxRate ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The range for configuring rate-limit in packet per second (pps).
Note that a particular agent may support different rate range.
Thus, the valid values are project dependent.
An agent may respond with an error (e.g., 'inconsistentValue ')
to a management SET operation which attempts to modify
the value to one which is not supported by the managed device.
The value -1 has a special meaning. When this object is
set to -1, there is no rate-limit of the entry."
SYNTAX Integer32 (-1 | 0..65535)
UnitID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This object indicates the slot (for a chassis device) or
unit number (for stacking device).
For a standalone device, 0 is used for UnitID.
Note that a particular agent may support different range
of unit/slot ID.
Thus, the valid values are project dependent.
An agent may respond with an error (e.g., 'inconsistentValue ')
to a management SET operation which attempts to modify
the value to one which is not supported by the managed device.
"
SYNTAX Integer32 (0 | 1..64)
--
-- Node definitions
--
dCpuProtectMIBNotifications OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 0 }
dCpuProtectMIBObjects OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 1 }
dCpuProtectMIBConformance OBJECT IDENTIFIER ::= { dlinkSwCpuProtectMIB 2 }
dCpuProtectMIBObjectsCtrl OBJECT IDENTIFIER ::= { dCpuProtectMIBObjects 2 }
-- ***************************************************************************
-- dCpuProtectProtoRateLimitTable
-- ***************************************************************************
dCpuProtectProtoRateLimitTable OBJECT-TYPE
SYNTAX SEQUENCE OF DCpuProtectProtoRateLimitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object configure the rate-limit of traffic destined to CPU
based on protocol type."
::= { dCpuProtectMIBObjectsCtrl 1 }
dCpuProtectProtoRateLimitEntry OBJECT-TYPE
SYNTAX DCpuProtectProtoRateLimitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object configures rate-limit control based on a specific
protocol type."
INDEX { dCpuProtectProtoRLType }
::= { dCpuProtectProtoRateLimitTable 1 }
DCpuProtectProtoRateLimitEntry ::=
SEQUENCE {
dCpuProtectProtoRLType CpuProtectProtocolType,
dCpuProtectProtoRLRate MaxRate,
dCpuProtectProtoRLClearCounter INTEGER
}
dCpuProtectProtoRLType OBJECT-TYPE
SYNTAX CpuProtectProtocolType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the protocol type."
::= { dCpuProtectProtoRateLimitEntry 1 }
dCpuProtectProtoRLRate OBJECT-TYPE
SYNTAX MaxRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the rate-limit of the specific
protocol type.
The value of -1 has the special meaning of identifying
that there is no rate-limit of the specific protocol type."
DEFVAL { -1 }
::= { dCpuProtectProtoRateLimitEntry 2 }
dCpuProtectProtoRLClearCounter OBJECT-TYPE
SYNTAX INTEGER
{ clear(1),
noOp(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to reset the counter of the specific
protocol type when set to 'clear'.
No action is taken if this object is set to 'noOp'.
When read, the value 'noOp' is returned."
DEFVAL { noOp }
::= { dCpuProtectProtoRateLimitEntry 3 }
-- ***************************************************************************
-- dCpuProtectSubIntfRLTable
-- ***************************************************************************
dCpuProtectSubIntfRLTable OBJECT-TYPE
SYNTAX SEQUENCE OF DCpuProtectSubIntfRLEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table consists of the rate-limit information of the
sub-interface."
::= { dCpuProtectMIBObjectsCtrl 2 }
dCpuProtectSubIntfRLEntry OBJECT-TYPE
SYNTAX DCpuProtectSubIntfRLEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object configure rate-limit control based on a specific
sub-interface."
INDEX { dCpuProtectSubIntfRLType }
::= { dCpuProtectSubIntfRLTable 1 }
DCpuProtectSubIntfRLEntry ::=
SEQUENCE {
dCpuProtectSubIntfRLType INTEGER,
dCpuProtectSubIntfRLRate MaxRate,
dCpuProtectSubIntfRLClearCounter INTEGER
}
dCpuProtectSubIntfRLType OBJECT-TYPE
SYNTAX INTEGER
{ manage(1),
protocol(2),
route(3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the type of sub-interface."
::= { dCpuProtectSubIntfRLEntry 1 }
dCpuProtectSubIntfRLRate OBJECT-TYPE
SYNTAX MaxRate
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the rate-limit of the specific
sub-interface.
The value of -1 has the special meaning of identifying
that there is no rate-limit of the specific sub-interface."
DEFVAL { -1 }
::= { dCpuProtectSubIntfRLEntry 2 }
dCpuProtectSubIntfRLClearCounter OBJECT-TYPE
SYNTAX INTEGER
{ clear(1),
noOp(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to reset the counter of the specific
sub-interface when set to 'clear'.
No action is taken if this object is set to 'noOp'.
When read, the value 'noOp' is returned."
DEFVAL { noOp }
::= { dCpuProtectSubIntfRLEntry 3 }
dCpuProtectMIBObjectsCounters OBJECT IDENTIFIER
::= { dCpuProtectMIBObjects 3 }
-- ***************************************************************************
-- dCpuProtectProtoRLCntTable
-- ***************************************************************************
dCpuProtectProtoRLCntTable OBJECT-TYPE
SYNTAX SEQUENCE OF DCpuProtectProtoRLCntEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table consists of the traffic statistics by protocol type."
::= { dCpuProtectMIBObjectsCounters 1 }
dCpuProtectProtoRLCntEntry OBJECT-TYPE
SYNTAX DCpuProtectProtoRLCntEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The per unit/slot traffic statistics about a protocol type.
Objects in this table are read-only and appear
automatically whenever the value of dCpuProtectProtoRLRate of a row
in the dCpuProtectProtoRateLimitTable is not -1 (no-limit)."
INDEX { dCpuProtectProtoRLCntType, dCpuProtectProtoRLCntUnitID }
::= { dCpuProtectProtoRLCntTable 1 }
DCpuProtectProtoRLCntEntry ::=
SEQUENCE {
dCpuProtectProtoRLCntType CpuProtectProtocolType,
dCpuProtectProtoRLCntUnitID UnitID,
dCpuProtectProtoRLCntTotalCnt Counter64,
dCpuProtectProtoRLCntDropCnt Counter64
}
dCpuProtectProtoRLCntType OBJECT-TYPE
SYNTAX CpuProtectProtocolType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the Protocol type."
::= { dCpuProtectProtoRLCntEntry 1 }
dCpuProtectProtoRLCntUnitID OBJECT-TYPE
SYNTAX UnitID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the unit/slot ID (for a chassis device)
or unit number (for stacking device). For a standalone device,
0 is used for UnitID."
::= { dCpuProtectProtoRLCntEntry 2 }
dCpuProtectProtoRLCntTotalCnt OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the counter which counts the packets
received by CPU (per unit/slot) for the protocol type."
::= { dCpuProtectProtoRLCntEntry 3 }
dCpuProtectProtoRLCntDropCnt OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the counter which counts the dropped
packets due to exceeding the configured rate-limit."
::= { dCpuProtectProtoRLCntEntry 4 }
-- ***************************************************************************
-- dCpuProtectSubIntfRLCounterTable
-- ***************************************************************************
dCpuProtectSubIntfRLCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DCpuProtectSubIntfRLCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table consists of the traffic statistics by sub-interface."
::= { dCpuProtectMIBObjectsCounters 2 }
dCpuProtectSubIntfRLCounterEntry OBJECT-TYPE
SYNTAX DCpuProtectSubIntfRLCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The per unit traffic statistics about a sub-interface.
Objects in this table are read-only and appear
automatically whenever the value of dCpuProtectSubIntfRLRate of a row
in the dCpuProtectSubIntfRLTable is not -1 (no-limit)."
INDEX { dCpuProtectSubIntfRLCntType, dCpuProtectSubIntfRLCntUnitID }
::= { dCpuProtectSubIntfRLCounterTable 1 }
DCpuProtectSubIntfRLCounterEntry ::=
SEQUENCE {
dCpuProtectSubIntfRLCntType INTEGER,
dCpuProtectSubIntfRLCntUnitID UnitID,
dCpuProtectSubIntfRLCntTotalCnt Counter64,
dCpuProtectSubIntfRLCntDropCnt Counter64
}
dCpuProtectSubIntfRLCntType OBJECT-TYPE
SYNTAX INTEGER
{ manage(1),
protocol(2),
route(3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the type of sub-interface."
::= { dCpuProtectSubIntfRLCounterEntry 1 }
dCpuProtectSubIntfRLCntUnitID OBJECT-TYPE
SYNTAX UnitID
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the slot (for a chassis device) or
unit number (for stacking device). For a standalone device,
0 is used for UnitID."
::= { dCpuProtectSubIntfRLCounterEntry 2 }
dCpuProtectSubIntfRLCntTotalCnt OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the counter which counts the packets
received by CPU (per unit/slot) for the subinterface."
::= { dCpuProtectSubIntfRLCounterEntry 3 }
dCpuProtectSubIntfRLCntDropCnt OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the counter which counts the dropped
packets due to exceeding the configured rate-limit."
::= { dCpuProtectSubIntfRLCounterEntry 4 }
-- ***************************************************************************
-- Conformance
-- ***************************************************************************
dCpuProtectMIBCompliances OBJECT IDENTIFIER ::= { dCpuProtectMIBConformance 1 }
dCpuProtectMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement the
DLINKSW-CPU-PROTECT-MIB."
MODULE -- this module
MANDATORY-GROUPS { dCpuProtectProtoGroup }
GROUP dCpuProtectSubIntfGroup
DESCRIPTION
"This group is required only if the agent implements
the rate-limit for traffic destined to CPU by sub-interface type."
::= { dCpuProtectMIBCompliances 1 }
dCpuProtectMIBGroups OBJECT IDENTIFIER ::= { dCpuProtectMIBConformance 2 }
dCpuProtectProtoGroup OBJECT-GROUP
OBJECTS
{ dCpuProtectProtoRLRate,
dCpuProtectProtoRLClearCounter,
dCpuProtectProtoRLCntTotalCnt,
dCpuProtectProtoRLCntDropCnt
}
STATUS current
DESCRIPTION
"A collection of objects providing the configuration or
statistics about the rate-limit of traffic destined to
CPU by protocol type."
::= { dCpuProtectMIBGroups 1 }
dCpuProtectSubIntfGroup OBJECT-GROUP
OBJECTS
{ dCpuProtectSubIntfRLRate,
dCpuProtectSubIntfRLClearCounter,
dCpuProtectSubIntfRLCntTotalCnt,
dCpuProtectSubIntfRLCntDropCnt
}
STATUS current
DESCRIPTION
"A collection of objects providing the configuration or
statistics about the rate-limit of traffic destined to
CPU by sub-interface type."
::= { dCpuProtectMIBGroups 2 }
END