mibs/MIBS/raisecom/RAISECOM-OPTICAL-MONITOR-MIB

823 lines
28 KiB
Plaintext
Raw Normal View History

2023-12-05 12:25:34 +01:00
--MibName=raisecomOpticalMonitorMIB
-- *****************************************************************
-- RAISECOM-OPTICAL-MONITOR-MIB.my
--
-- May 2006, chenyu
--
-- Copyright(c) 2003-2005 by RAISECOM TECH, Ltd.
-- All rights reserved.
-- *****************************************************************
RAISECOM-OPTICAL-MONITOR-MIB DEFINITIONS ::= BEGIN
IMPORTS
Integer32, Unsigned32,
MODULE-IDENTITY,
NOTIFICATION-TYPE,
OBJECT-TYPE,
TimeTicks FROM SNMPv2-SMI
TEXTUAL-CONVENTION FROM SNMPv2-TC
MODULE-COMPLIANCE,
NOTIFICATION-GROUP,
OBJECT-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
EnableVar FROM SWITCH-TC
raisecomAgent FROM RAISECOM-BASE-MIB;
raisecomOpticalMonitorMIB MODULE-IDENTITY
LAST-UPDATED "200606060000Z"
ORGANIZATION "Raisecom, Inc."
CONTACT-INFO
" Raise Systems
Postal: Beijing,
China
Tel: 86-010-82884499
E-mail: chenyu@raisecom.com"
DESCRIPTION
"This MIB module defines objects to monitor optical
characteristics on the optical interfaces in a network element. "
REVISION "200606060000Z"
DESCRIPTION
"The initial revision of this MIB."
::={ raisecomAgent 9 }
-- Textual Conventions
OpticalParameterType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the optical parameter that is
being monitored. Valid values are -
temperature(1)
supplyVoltage(2)
biasCurrent(3)
txOutputPower(4)
receivedPower(5) "
SYNTAX INTEGER {
temperature(1),
supplyVoltage(2),
biasCurrent(3),
txOutputPower(4),
receivedPower(5)
}
OpticalParameterValue ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of the optical parameter that is being monitored.
The range of values varies depending on the type of optical
parameter being monitored, as identified by a corresponding
object with syntax OpticalParameterType.
When the optical parameter being monitored is 'temperature',
the supported range is from -32768 to 32768, in units of
1/256 degrees centigrade.
Example: A value of 6016 represents a temperature reading of
23.5 degrees C.
When the optical parameter being monitored is 'supplyVoltage',
the supported range is from 0 to 65535, in units of 1/10 millivolts.
Example: A value of 55000 represents a supplyVoltage reading of
5.5 V.
When the optical parameter being monitored is 'biasCurrent',
the supported range is from 0 to 65535, in units of 1/500
microamperes.
Example: A value of 500 represents a bias current reading of
1 microamperes.
When the optical parameter being monitored is 'txOutputPower',
the supported range is from 0 to 65535, in units of 1/10000 mW ..and express in units of dBm<42><6D>
Example: A value of 60000 represents a txOutputPower reading of 7.78 dBm.
When the optical parameter being monitored is 'receivedPower',
the supported range is from 0 to 65535, in units of 1/10000 mW ..and express in units of dBm<42><6D>
Example: A value of 60000 represents a receivedPower reading of 7.78 dBm. "
SYNTAX Integer32 (-1000000..65535 )
OpticalPMPeriod ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the time period over which performance
monitoring data has been collected."
SYNTAX INTEGER {
fifteenMin(1),
twentyFourHour(2)
}
-- MIB Object Definitions
raisecomOpticalMonitorMIBObjects OBJECT IDENTIFIER ::=
{raisecomOpticalMonitorMIB 1 }
-- groups in this MIB module
raisecomOpticalMonGroup OBJECT IDENTIFIER ::=
{raisecomOpticalMonitorMIBObjects 1 }
raisecomOpticalPMGroup OBJECT IDENTIFIER ::=
{raisecomOpticalMonitorMIBObjects 2 }
-- raisecomTranceiverInfoTable
raisecomTranceiverInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaisecomTranceiverInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Trancetver information Table."
::= { raisecomOpticalMonitorMIBObjects 4 }
raisecomTranceiverInfoEntry OBJECT-TYPE
SYNTAX RaisecomTranceiverInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the raisecomSfpAccessA0Table."
INDEX { ifIndex }
::={ raisecomTranceiverInfoTable 1 }
RaisecomTranceiverInfoEntry ::= SEQUENCE {
raisecomTranceiverType OCTET STRING,
raisecomTranceiverConnectorType OCTET STRING,
raisecomTranceiverWavelength Integer32,
raisecomTranceiverVendorName OCTET STRING,
raisecomTranceiverVendorPN OCTET STRING,
raisecomTranceiverVendorSN OCTET STRING,
raisecomTransceiverFiberType INTEGER,
raisecomTransceiverTransferDistance Integer32
}
raisecomTranceiverType OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION
"Type of the interface, such as 1000_BASE_SX_SFP"
::= { raisecomTranceiverInfoEntry 1 }
raisecomTranceiverConnectorType OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION
"ConnectorType of the interface, such as SC/LC"
::= { raisecomTranceiverInfoEntry 2 }
raisecomTranceiverWavelength OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION
"Wavelength of the interface, measured in nm."
::= { raisecomTranceiverInfoEntry 3 }
raisecomTranceiverVendorName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION
"Vendor name of the interface."
::= { raisecomTranceiverInfoEntry 4 }
raisecomTranceiverVendorPN OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION
"Vendor part number of the interface."
::= { raisecomTranceiverInfoEntry 5 }
raisecomTranceiverVendorSN OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number of the interface."
::= { raisecomTranceiverInfoEntry 6 }
raisecomTransceiverFiberType OBJECT-TYPE
SYNTAX INTEGER
{
single-mode(1),
multi-mode(2),
none(3)
}
ACCESS read-only
STATUS current
DESCRIPTION
"Types of the fiber,
single_mode, multi_mode, none."
::= { raisecomTranceiverInfoEntry 7 }
raisecomTransceiverTransferDistance OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION
"The max distance which the interface could transmit,
measured in meter."
::= { raisecomTranceiverInfoEntry 8 }
-- raisecomOpticalMonTable
raisecomOpticalMonTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaisecomOpticalMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides objects to monitor optical
parameters in a network element. "
::={ raisecomOpticalMonGroup 1 }
raisecomOpticalMonEntry OBJECT-TYPE
SYNTAX RaisecomOpticalMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the raisecomOpticalMonTable provides objects to
monitor an optical parameter at an optical interface.
"
INDEX { ifIndex, raisecomOpticalMonParameterType }
::={ raisecomOpticalMonTable 1 }
RaisecomOpticalMonEntry ::= SEQUENCE {
raisecomOpticalMonParameterType OpticalParameterType,
raisecomOpticalParameterValue OpticalParameterValue,
raisecomOpticalParamHighAlarmThresh OpticalParameterValue,
raisecomOpticalParamHighWarningThresh OpticalParameterValue,
raisecomOpticalParamLowAlarmThresh OpticalParameterValue,
raisecomOpticalParamLowWarningThresh OpticalParameterValue,
raisecomOpticalParamAlarmStatus INTEGER,
raisecomOpticalParamAlarmLastValue OpticalParameterValue,
raisecomOpticalParamAlarmLastChange TimeTicks,
raisecomOpticalMon15MinValidIntervals Unsigned32,
raisecomOpticalMon24HrValidIntervals Unsigned32,
raisecomOpticalMonValidStatus INTEGER
}
raisecomOpticalMonParameterType OBJECT-TYPE
SYNTAX OpticalParameterType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the optical parameter that is being
monitored in this entry."
::={ raisecomOpticalMonEntry 1 }
raisecomOpticalParameterValue OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the value measured for the particular
optical parameter specified by the raisecomOpticalMonParameterType
object."
::={ raisecomOpticalMonEntry 2 }
raisecomOpticalParamHighAlarmThresh OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the high alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
raisecomOpticalParameterValue goes from below the value of
this object to above the value of this object, or if
the initial value of raisecomOpticalParameterValue exceeds the value
of this object. This alarm will be indicated in the
raisecomOpticalParamAlarmStatus object."
::={ raisecomOpticalMonEntry 3 }
raisecomOpticalParamHighWarningThresh OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set a high warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by raisecomOpticalParameterValue goes from below the value
of this object to above the value of this
object, or if the initial value of raisecomOpticalParameterValue
exceeds the value of this object. This alarm will be indicated in the
raisecomOpticalParamAlarmStatus object.
"
::={ raisecomOpticalMonEntry 4 }
raisecomOpticalParamLowAlarmThresh OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
raisecomOpticalParameterValue goes from above the value of
this object to below the value of this object, or if
the initial value of raisecomOpticalParameterValue is lower than the
value of this object. This alarm
will be indicated in the raisecomOpticalParamAlarmStatus object .."
::={ raisecomOpticalMonEntry 5 }
raisecomOpticalParamLowWarningThresh OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set a low warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by raisecomOpticalParameterValue goes from above the value
of this object to below the value of this
object, or if the initial value of raisecomOpticalParameterValue
object is lower than the value of this object. For
network elements in the status
indications, this threshold violation will be indicated in the
raisecomOpticalParamAlarmStatus object ."
::={ raisecomOpticalMonEntry 6 }
raisecomOpticalParamAlarmStatus OBJECT-TYPE
SYNTAX INTEGER {
none(0),
high-alarm-threshold(1),
high-warning-threshold(2),
low-alarm-threshold(3),
low-warning-threshold(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate the current status of
the thresholds for the monitored optical parameter
on the interface.
If a threshold is currently being exceeded on the
interface, the object will be set. Otherwise,
the object will be set to 0."
::={ raisecomOpticalMonEntry 7 }
raisecomOpticalParamAlarmLastValue OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the optical parameter value at the last time
a threshold related to a particular optical parameter was
exceeded on the interface.
If no threshold value is currently being
exceeded, then the value '-1000000' is returned."
::={ raisecomOpticalMonEntry 8 }
raisecomOpticalParamAlarmLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the value of sysUpTime at the last time
a threshold related to a particular optical parameter was
exceeded on the interface."
::={ raisecomOpticalMonEntry 9 }
raisecomOpticalMon15MinValidIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the number of previous 15 minute
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of previous 15 minute intervals for which the agent
has some data."
::={ raisecomOpticalMonEntry 10 }
raisecomOpticalMon24HrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..1)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the number of previous 24 hour
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object will be 0 if the measurement
was (re-)started within the last 24 hours, or 1 otherwise."
::={ raisecomOpticalMonEntry 11 }
raisecomOpticalMonValidStatus OBJECT-TYPE
SYNTAX INTEGER {
valid(1),
invalid(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the parameter row is valid or not."
::={ raisecomOpticalMonEntry 12 }
-- Notification related objects
raisecomOpticalNotifyEnable OBJECT-TYPE
SYNTAX EnableVar
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the generation of raisecomOpticalMonParameterStatus notifications.
"
DEFVAL { enable}
::={ raisecomOpticalMonGroup 2 }
raisecomOpticalDigitalDiagnoticEnable OBJECT-TYPE
SYNTAX EnableVar
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable digitaldiagnotic on the switch."
DEFVAL { disable}
::={ raisecomOpticalMonGroup 3 }
-- raisecomOpticalPMCurrent Table
raisecomOpticalPMCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaisecomOpticalPMCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains performance monitoring data for the
various optical parameters, collected over the current 15
minute or the current 24 hour interval."
::={ raisecomOpticalPMGroup 1 }
raisecomOpticalPMCurrentEntry OBJECT-TYPE
SYNTAX RaisecomOpticalPMCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the raisecomOpticalPMCurrentTable. It contains
performance monitoring data for a monitored optical
parameter at an interface, collected over the current 15
minute or the current 24 hour interval.
"
INDEX { ifIndex,
raisecomOpticalPMCurrentPeriod,
raisecomOpticalPMCurrentParamType }
::={ raisecomOpticalPMCurrentTable 1 }
RaisecomOpticalPMCurrentEntry ::= SEQUENCE {
raisecomOpticalPMCurrentPeriod OpticalPMPeriod,
raisecomOpticalPMCurrentParamType OpticalParameterType,
raisecomOpticalPMCurrentMaxParam OpticalParameterValue,
raisecomOpticalPMCurrentMinParam OpticalParameterValue,
raisecomOpticalPMCurrentMeanParam OpticalParameterValue
}
raisecomOpticalPMCurrentPeriod OBJECT-TYPE
SYNTAX OpticalPMPeriod
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates whether the optical parameter values
given in this entry are collected over the current 15 minute or
the current 24 hour interval."
::={ raisecomOpticalPMCurrentEntry 1 }
raisecomOpticalPMCurrentParamType OBJECT-TYPE
SYNTAX OpticalParameterType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the optical parameter that is being
monitored, in this entry."
::={ raisecomOpticalPMCurrentEntry 2 }
raisecomOpticalPMCurrentMaxParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the maximum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval."
::={ raisecomOpticalPMCurrentEntry 3 }
raisecomOpticalPMCurrentMinParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the minimum value measured for the monitored
optical parameter, in the current 15 minute or the current
24 hour interval."
::={ raisecomOpticalPMCurrentEntry 4 }
raisecomOpticalPMCurrentMeanParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the average value of the monitored
optical parameter, in the current 15 minute or the current
24 hour interval."
::={ raisecomOpticalPMCurrentEntry 5 }
-- raisecomOpticalPMInterval Table
raisecomOpticalPMIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF RaisecomOpticalPMIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table stores performance monitoring data for the
various optical parameters, collected over previous
intervals.
This table can have entries for one complete 24 hour
interval and up to 96 complete 15 minute
intervals. A system is required to store at least
4 completed 15 minute intervals. The number of valid
15 minute intervals in this table is indicated by the
cOpticalMon15MinValidIntervals object and the number of
valid 24 hour intervals is indicated by the
cOpticalMon24HrValidIntervals object."
::={ raisecomOpticalPMGroup 2 }
raisecomOpticalPMIntervalEntry OBJECT-TYPE
SYNTAX RaisecomOpticalPMIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the raisecomOpticalPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over a previous interval.
"
INDEX { ifIndex,
raisecomOpticalPMIntervalPeriod,
raisecomOpticalPMIntervalNumber,
raisecomOpticalPMIntervalParamType }
::={ raisecomOpticalPMIntervalTable 1 }
RaisecomOpticalPMIntervalEntry ::= SEQUENCE {
raisecomOpticalPMIntervalPeriod OpticalPMPeriod,
raisecomOpticalPMIntervalNumber Integer32,
raisecomOpticalPMIntervalParamType OpticalParameterType,
raisecomOpticalPMIntervalMaxParam OpticalParameterValue,
raisecomOpticalPMIntervalMinParam OpticalParameterValue,
raisecomOpticalPMIntervalMeanParam OpticalParameterValue
}
raisecomOpticalPMIntervalPeriod OBJECT-TYPE
SYNTAX OpticalPMPeriod
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates whether the optical parameter values,
given in this entry, are collected over a period of 15 minutes
or 24 hours."
::={ raisecomOpticalPMIntervalEntry 1 }
raisecomOpticalPMIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of optical parameter values is
available. The interval identified by 1 is the most recently
completed 15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the one
identified by N-1."
::={ raisecomOpticalPMIntervalEntry 2 }
raisecomOpticalPMIntervalParamType OBJECT-TYPE
SYNTAX OpticalParameterType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the optical parameter that is being
monitored, in this entry."
::={ raisecomOpticalPMIntervalEntry 3 }
raisecomOpticalPMIntervalMaxParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval."
::={ raisecomOpticalPMIntervalEntry 4 }
raisecomOpticalPMIntervalMinParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval."
::={ raisecomOpticalPMIntervalEntry 5 }
raisecomOpticalPMIntervalMeanParam OBJECT-TYPE
SYNTAX OpticalParameterValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval."
::={ raisecomOpticalPMIntervalEntry 6 }
-- Notifications
raisecomOpticalMonitorMIBNotifications OBJECT IDENTIFIER ::=
{ raisecomOpticalMonitorMIB 2 }
raisecomOpticalMonParameterStatus NOTIFICATION-TYPE
OBJECTS { raisecomOpticalParameterValue,
raisecomOpticalParamAlarmStatus
}
STATUS current
DESCRIPTION
"This notification is sent when any threshold related to an
optical parameter is exceeded on an interface.
This notification may be suppressed under the following
conditions:
- depending on the value of the raisecomOpticalNotifyEnable object.
"
::={ raisecomOpticalMonitorMIBNotifications 1 }
-- MIB Conformance Statements
raisecomOpticalMonitorMIBConformance OBJECT IDENTIFIER ::=
{ raisecomOpticalMonitorMIB 3 }
raisecomOpticalMonitorMIBCompliances OBJECT IDENTIFIER ::=
{ raisecomOpticalMonitorMIBConformance 1 }
raisecomOpticalMonitorMIBGroups OBJECT IDENTIFIER ::=
{ raisecomOpticalMonitorMIBConformance 2 }
raisecomOpticalMonitorMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for network elements that
monitor optical characteristics and thresholds on the
optical interfaces in a network element."
MODULE -- this module
MANDATORY-GROUPS { raisecomOpticalMIBMonGroup }
GROUP raisecomOpticalMIBThresholdGroup
DESCRIPTION
"This group is required for network elements that support
thresholds on optical parameters."
GROUP raisecomOpticalMIBPMGroup
DESCRIPTION
"This group is required for network elements that
support collection of optical performance monitoring
data for 15 minute or 24 hour intervals."
GROUP raisecomOpticalMIBNotifyEnableGroup
DESCRIPTION
"This group is required for network elements that
support the cOpticalMIBNotifGroup."
GROUP raisecomOpticalMIBNotifGroup
DESCRIPTION
"This group is required for network elements that
generate notifications when a threshold is exceeded or
cleared on an interface."
OBJECT raisecomOpticalParamHighAlarmThresh
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamHighWarningThresh
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamLowAlarmThresh
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamLowWarningThresh
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamHighAlarmSev
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamHighWarningSev
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamLowAlarmSev
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT raisecomOpticalParamLowWarningSev
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::={ raisecomOpticalMonitorMIBCompliances 1 }
-- Units of Conformance
raisecomOpticalMIBMonGroup OBJECT-GROUP
OBJECTS {
raisecomOpticalParameterValue
}
STATUS current
DESCRIPTION
"A mandatory object that provides monitoring of optical
characteristics."
::={ raisecomOpticalMonitorMIBGroups 1 }
raisecomOpticalMIBThresholdGroup OBJECT-GROUP
OBJECTS {
raisecomOpticalParamHighAlarmThresh,
raisecomOpticalParamHighWarningThresh,
raisecomOpticalParamLowAlarmThresh,
raisecomOpticalParamLowWarningThresh,
raisecomOpticalParamAlarmStatus,
raisecomOpticalParamAlarmLastValue,
raisecomOpticalParamAlarmLastChange
}
STATUS current
DESCRIPTION
"A collection of objects that support thresholds on optical
parameters and provide status information when the thresholds
are exceeded ."
::={ raisecomOpticalMonitorMIBGroups 2 }
raisecomOpticalMIBPMGroup OBJECT-GROUP
OBJECTS {
raisecomOpticalMon15MinValidIntervals,
raisecomOpticalMon24HrValidIntervals,
raisecomOpticalPMCurrentMaxParam,
raisecomOpticalPMCurrentMinParam,
raisecomOpticalPMCurrentMeanParam,
raisecomOpticalPMIntervalMaxParam,
raisecomOpticalPMIntervalMinParam,
raisecomOpticalPMIntervalMeanParam
}
STATUS current
DESCRIPTION
"A collection of objects that provide optical performance
monitoring data for 15 minute and 24 hour intervals."
::={ raisecomOpticalMonitorMIBGroups 3 }
raisecomOpticalMIBNotifyEnableGroup OBJECT-GROUP
OBJECTS {
raisecomOpticalNotifyEnable
}
STATUS current
DESCRIPTION
"An object to control the generation of notifications."
::={ raisecomOpticalMonitorMIBGroups 4 }
raisecomOpticalMIBNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS {
raisecomOpticalMonParameterStatus
}
STATUS current
DESCRIPTION
"A notification generated when a threshold on an optical
parameter is exceeded or cleared."
::={ raisecomOpticalMonitorMIBGroups 5 }
END