Initial commit

MIBS/cisco/CISCO-L2L3-INTERFACE-CONFIG-MIB

@@ -0,0 +1,184 @@
+-- *****************************************************************
+-- CISCO-L2L3-INTERFACE-CONFIG-MIB - 
+--    configuration of switchport mode for interfaces
+--
+-- February 2000, Cliff Sojourner
+--
+-- Copyright (c) 2000 by cisco Systems, Inc.
+-- All rights reserved.
+-- *****************************************************************
+--
+
+CISCO-L2L3-INTERFACE-CONFIG-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY,
+    OBJECT-TYPE
+        FROM SNMPv2-SMI
+    MODULE-COMPLIANCE,
+    OBJECT-GROUP
+        FROM SNMPv2-CONF
+    TEXTUAL-CONVENTION
+        FROM SNMPv2-TC
+    ifIndex
+        FROM IF-MIB
+    ciscoMgmt
+        FROM CISCO-SMI
+    ;
+
+ciscoL2L3IfConfigMIB MODULE-IDENTITY
+    LAST-UPDATED        "200005101900Z"
+    ORGANIZATION        "Cisco Systems, Inc."
+    CONTACT-INFO
+        "Cisco Systems
+        Customer Service
+
+        Postal: 170 W Tasman Drive
+                San Jose, CA  95134
+                USA
+
+        Tel: +1 800 553-NETS
+
+        E-mail: cs-snmp@cisco.com"
+    DESCRIPTION
+        "Interface switchport mode configuration management MIB.
+
+        This MIB is used to monitor and control 
+        configuration of interface switchport and routed mode."
+    REVISION        "200005101900Z"
+    DESCRIPTION
+        "Initial version of this MIB module."
+    ::= { ciscoMgmt 151 }
+
+ciscoL2L3IfConfigMIBObjects OBJECT IDENTIFIER ::=  { ciscoL2L3IfConfigMIB 1 }
+
+cL2L3IfConfig OBJECT IDENTIFIER ::=  { ciscoL2L3IfConfigMIBObjects 1 }
+
+--
+-- Textual Conventions
+--
+
+CL2L3InterfaceMode ::= TEXTUAL-CONVENTION
+    STATUS        current
+    DESCRIPTION
+        "The operational mode of the interface.
+
+        For administrative and operational states, valid values are: 
+        routed(1), switchport(2).
+        
+        routed(1): Routed mode interfaces direct traffic using 
+        layer 3 protocols.
+
+        switchport(2):  Switchport-mode interfaces direct traffic using 
+        layer 2 protocols.  A switchport-mode interface can be in
+        access mode, or trunk mode, or multi-mode.
+
+        Switchport interface operating mode can be configured manually,
+        or negotiated by Dynamic Trunking Protocol (DTP) or Dynamic 
+        Inter-Switch Link (DISL).
+
+        Access-mode interfaces carry one VLAN's traffic.  Access-mode
+        interface parameters are configured in CISCO-VLAN-MEMBERSHIP-MIB.
+
+        Trunk-mode interfaces carry one or more VLANs.  VLAN-related 
+        trunk-mode interface parameters are configured in CISCO-VTP-MIB.
+
+        Multi-mode interfaces carry one VLAN to each alias of a 
+        single connected end-station.  VLAN-related multi-mode 
+        interface parameters are configured in CISCO-VTP-MIB.
+        "
+    SYNTAX INTEGER { routed(1), switchport(2) }
+
+--
+-- switchport interface mode configuration table
+--
+
+cL2L3IfTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF CL2L3IfEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "The table shows the administratively requested and
+        actual operating configuration for switchport interfaces."
+    ::= { cL2L3IfConfig 1 }
+
+cL2L3IfEntry OBJECT-TYPE
+    SYNTAX     CL2L3IfEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+        "An entry represents the configuration and operation of a
+        switchport interface.
+
+        Entries are created and deleted automatically in tandem 
+        with the corresponding ifEntries."
+    INDEX      { ifIndex }
+    ::= { cL2L3IfTable 1 }
+
+CL2L3IfEntry ::= SEQUENCE {
+    cL2L3IfModeAdmin    CL2L3InterfaceMode,
+    cL2L3IfModeOper     CL2L3InterfaceMode
+    } 
+
+cL2L3IfModeAdmin OBJECT-TYPE
+    SYNTAX     CL2L3InterfaceMode
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION 
+        "The administratively desired interface mode."
+    ::= { cL2L3IfEntry 1 }
+
+cL2L3IfModeOper OBJECT-TYPE
+    SYNTAX     CL2L3InterfaceMode
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION 
+        "The operational interface mode."
+    ::= { cL2L3IfEntry 2 }
+
+
+--
+-- Notifications
+--
+
+-- ciscoL2L3IfConfigMIBNotificationPrefix OBJECT IDENTIFIER ::= 
+--     { ciscoL2L3IfConfigMIB 2 }
+-- ciscoL2L3IfConfigMIBNotifications OBJECT IDENTIFIER ::=
+--     { ciscoL2L3IfConfigMIBNotificationPrefix 0 }
+
+
+--
+-- Conformance
+--
+
+ciscoL2L3IfConfigMIBConformance OBJECT IDENTIFIER 
+    ::= { ciscoL2L3IfConfigMIB 3 }
+ciscoL2L3IfConfigMIBCompliances OBJECT IDENTIFIER 
+    ::= { ciscoL2L3IfConfigMIBConformance 1 }
+ciscoL2L3IfConfigMIBGroups      OBJECT IDENTIFIER 
+    ::= { ciscoL2L3IfConfigMIBConformance 2 }
+
+ciscoL2L3IfConfigMIBCompliance MODULE-COMPLIANCE
+    STATUS current
+    DESCRIPTION
+        "The compliance statement for entities which implement
+         the Cisco L2L3 Interface Configuration Management MIB"
+    MODULE        -- this module
+        MANDATORY-GROUPS { ciscoL2L3IfConfigMIBGroup }
+    ::= { ciscoL2L3IfConfigMIBCompliances 1 }
+
+--
+-- Units of Conformance
+--
+
+ciscoL2L3IfConfigMIBGroup OBJECT-GROUP
+    OBJECTS {
+        cL2L3IfModeAdmin,
+        cL2L3IfModeOper
+    }
+    STATUS current
+    DESCRIPTION
+        "Interface L2 & L3 mode objects"
+    ::= { ciscoL2L3IfConfigMIBGroups 1 }
+
+END