-- file: ADSL-LINE-EXT-MIB.my -- Extracted from RFC3440 by MG-SOFT Corp. -- Changes: -- No changes needed. -- http://www.mg-soft.com/ ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN IMPORTS Counter32, Integer32, NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB AdslPerfCurrDayCount, AdslPerfPrevDayCount FROM ADSL-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB adslLineAlarmConfProfileEntry, adslLineConfProfileEntry, adslAturIntervalEntry, adslAturPerfDataEntry, adslAtucIntervalEntry, adslAtucPerfDataEntry, adslLineEntry, adslMIB FROM ADSL-LINE-MIB ; adslExtMIB MODULE-IDENTITY LAST-UPDATED "200212100000Z" -- 10 Dec 2002 ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO " Faye Ly Pedestal Networks 6503 Dumbarton Circle, Fremont, CA 94555 Tel: +1 510-578-0158 Fax: +1 510-744-5152 E-Mail: faye@pedestalnetworks.com Gregory Bathrick Nokia Networks 2235 Mercury Way, Fax: +1 707-535-7300 E-Mail: greg.bathrick@nokia.com General Discussion:adslmib@ietf.org To Subscribe: https://www1.ietf.org/mailman/listinfo/adslmib Archive: https://www1.ietf.org/mailman/listinfo/adslmib " DESCRIPTION "Copyright (C) The Internet Society (2002). This version of this MIB module is part of RFC 3440; see the RFC itself for full legal notices. This MIB Module is a supplement to the ADSL-LINE-MIB [RFC2662]." REVISION "200212100000Z" -- 10 dec 2002 DESCRIPTION "Initial Version, published as RFC 3440. This MIB module supplements the ADSL-LINE-MIB [RFC2662]." ::= { adslMIB 3 } adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 } AdslTransmissionModeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A set of ADSL line transmission modes, with one bit per mode. The notes (F) and (L) denote Full-Rate and G.Lite respectively: Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 02 : G.992.1 POTS non-overlapped (F) Bit 03 : G.992.1 POTS overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 08 : G.992.2 POTS non-overlapped (L) Bit 09 : G.992.2 POTS overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 12 : G.992.1 TCM-ISDN symmetric (F) " SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12) } adslLineExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extension of RFC 2662. It contains ADSL line configuration and monitoring information. This includes the ADSL line's capabilities and actual ADSL transmission system." ::= { adslExtMibObjects 17 } adslLineExtEntry OBJECT-TYPE SYNTAX AdslLineExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslLineEntry } ::= { adslLineExtTable 1 } AdslLineExtEntry ::= SEQUENCE { adslLineTransAtucCap AdslTransmissionModeType, adslLineTransAtucConfig AdslTransmissionModeType, adslLineTransAtucActual AdslTransmissionModeType, adslLineGlitePowerState INTEGER, adslLineConfProfileDualLite SnmpAdminString } adslLineTransAtucCap OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission modes, represented by a bitmask that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment." REFERENCE "Section 7.3.2 ITU G.997.1" ::= { adslLineExtEntry 1 } adslLineTransAtucConfig OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission modes, represented by a bitmask, currently enabled by the ATU-C. The manager can only set those modes that are supported by the ATU-C. An ATU-C's supported modes are provided by AdslLineTransAtucCap." REFERENCE "Section 7.3.2 ITU G.997.1" ::= { adslLineExtEntry 2 } adslLineTransAtucActual OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit - Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by adslLineTransAtucConfig. After an initialization has occurred, its mode is saved as the 'Current' mode and is persistence should the link go down. This object returns 0 (i.e. BITS with no mode bit set) if the mode is not known." REFERENCE "Section 7.3.2 ITU G.997.1 " ::= { adslLineExtEntry 3 } adslLineGlitePowerState OBJECT-TYPE SYNTAX INTEGER { none(1), l0(2), -- L0 Power on l1(3), -- L1 Power on but reduced l3(4) -- L3 Power off } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object specifies the power state of this interface. L0 is power on, L1 is power on but reduced and L3 is power off. Power state cannot be configured by an operator but it can be viewed via the ifOperStatus object for the managed ADSL interface. The value of the object ifOperStatus is set to down(2) if the ADSL interface is in power state L3 and is set to up(1) if the ADSL line interface is in power state L0 or L1. If the object adslLineTransAtucActual is set to a G.992.2 (G.Lite)-type transmission mode, the value of this object will be one of the valid power states: L0(2), L1(3), or L3(4). Otherwise, its value will be none(1)." ::= { adslLineExtEntry 4 } adslLineConfProfileDualLite OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object extends the definition an ADSL line and associated channels (when applicable) for cases when it is configured in dual mode, and operating in a G.Lite-type mode as denoted by adslLineTransAtucActual. Dual mode exists when the object, adslLineTransAtucConfig, is configured with one or more full-rate modes and one or more G.Lite modes simultaneously. When 'dynamic' profiles are implemented, the value of object is equal to the index of the applicable row in the ADSL Line Configuration Profile Table, AdslLineConfProfileTable defined in ADSL-MIB [RFC2662]. In the case when dual-mode has not been enabled, the value of the object will be equal to the value of the object adslLineConfProfile [RFC2662]. When `static' profiles are implemented, in much like the case of the object, adslLineConfProfileName [RFC2662], this object's value will need to algorithmically represent the characteristics of the line. In this case, the value of the line's ifIndex plus a value indicating the line mode type (e.g., G.Lite, Full-rate) will be used. Therefore, the profile's name is a string concatenating the ifIndex and one of the follow values: Full or Lite. This string will be fixed-length (i.e., 14) with leading zero(s). For example, the profile name for ifIndex that equals '15' and is a full rate line, it will be '0000000015Full'." REFERENCE "Section 5.4 Profiles, RFC 2662" ::= { adslLineExtEntry 5 } adslAtucPerfDataExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends adslAtucPerfDataTable [RFC2662] with additional ADSL physical line counter information such as unavailable seconds-line and severely errored seconds-line." ::= { adslExtMibObjects 18 } adslAtucPerfDataExtEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslAtucPerfDataEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslAtucPerfDataEntry } ::= { adslAtucPerfDataExtTable 1 } AdslAtucPerfDataExtEntry ::= SEQUENCE { adslAtucPerfStatFastR Counter32, adslAtucPerfStatFailedFastR Counter32, adslAtucPerfStatSesL Counter32, adslAtucPerfStatUasL Counter32, adslAtucPerfCurr15MinFastR PerfCurrentCount, adslAtucPerfCurr15MinFailedFastR PerfCurrentCount, adslAtucPerfCurr15MinSesL PerfCurrentCount, adslAtucPerfCurr15MinUasL PerfCurrentCount, adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount, adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount, adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount, adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount, adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount, adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount, adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount, adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount } adslAtucPerfStatFastR OBJECT-TYPE SYNTAX Counter32 UNITS "line retrains" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of the number of fast line bs since last agent reset." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 1 } adslAtucPerfStatFailedFastR OBJECT-TYPE SYNTAX Counter32 UNITS "line retrains" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of the number of failed fast line retrains since last agent reset." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 2 } adslAtucPerfStatSesL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of the number of severely errored seconds-line since last agent reset." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 3 } adslAtucPerfStatUasL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of the number of unavailable seconds-line since last agent reset." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 4 } adslAtucPerfCurr15MinFastR OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAtucPerfCurr15MinFastR reports the current number of seconds during which there have been fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 5 } adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAtucPerfCurr15MinFailedFastR reports the current number of seconds during which there have been failed fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 6 } adslAtucPerfCurr15MinSesL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAtucPerfCurr15MinSesL reports the current number of seconds during which there have been severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 7 } adslAtucPerfCurr15MinUasL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAtucPerfCurr15MinUasL reports the current number of seconds during which there have been unavailable seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 8 } adslAtucPerfCurr1DayFastR OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAtucPerfCurr1DayTimeElapsed [RFC2662], adslAtucPerfCurr1DayFastR reports the number of seconds during which there have been fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 9 } adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAtucPerfCurr1DayTimeElapsed [RFC2662], adslAtucPerfCurr1DayFailedFastR reports the number of seconds during which there have been failed fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 10 } adslAtucPerfCurr1DaySesL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAtucPerfCurr1DayTimeElapsed [RFC2662], adslAtucPerfCurr1DaySesL reports the number of seconds during which there have been severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 11 } adslAtucPerfCurr1DayUasL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAtucPerfCurr1DayTimeElapsed [RFC2662], adslAtucPerfCurr1DayUasL reports the number of seconds during which there have been unavailable seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 12 } adslAtucPerfPrev1DayFastR OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAtucPerfPrev1DayFastR reports the number of seconds during which there were fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 13 } adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAtucPerfPrev1DayFailedFastR reports the number of seconds during which there were failed fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 14 } adslAtucPerfPrev1DaySesL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAtucPerfPrev1DaySesL reports the number of seconds during which there were severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 15 } adslAtucPerfPrev1DayUasL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAtucPerfPrev1DayUasL reports the number of seconds during which there were unavailable seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 16 } adslAtucIntervalExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATU-C performance data collection interval for ADSL physical interfaces whose IfEntries' ifType is equal to adsl(94)." ::= { adslExtMibObjects 19 } adslAtucIntervalExtEntry OBJECT-TYPE SYNTAX AdslAtucIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalExtTable." AUGMENTS { adslAtucIntervalEntry } ::= { adslAtucIntervalExtTable 1 } AdslAtucIntervalExtEntry ::= SEQUENCE { adslAtucIntervalFastR PerfIntervalCount, adslAtucIntervalFailedFastR PerfIntervalCount, adslAtucIntervalSesL PerfIntervalCount, adslAtucIntervalUasL PerfIntervalCount } adslAtucIntervalFastR OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current interval, adslAtucIntervalFastR reports the current number of seconds during which there have been fast retrains." ::= { adslAtucIntervalExtEntry 1 } adslAtucIntervalFailedFastR OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the each interval, adslAtucIntervalFailedFastR reports the number of seconds during which there have been failed fast retrains." ::= { adslAtucIntervalExtEntry 2 } adslAtucIntervalSesL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the each interval, adslAtucIntervalSesL reports the number of seconds during which there have been severely errored seconds-line." ::= { adslAtucIntervalExtEntry 3 } adslAtucIntervalUasL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the each interval, adslAtucIntervalUasL reports the number of seconds during which there have been unavailable seconds-line." ::= { adslAtucIntervalExtEntry 4 } adslAturPerfDataExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ADSL physical line counters not defined in the adslAturPerfDataTable from the ADSL-LINE-MIB [RFC2662]." ::= { adslExtMibObjects 20 } adslAturPerfDataExtEntry OBJECT-TYPE SYNTAX AdslAturPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslAturPerfDataEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslAturPerfDataEntry } ::= { adslAturPerfDataExtTable 1 } AdslAturPerfDataExtEntry ::= SEQUENCE { adslAturPerfStatSesL Counter32, adslAturPerfStatUasL Counter32, adslAturPerfCurr15MinSesL PerfCurrentCount, adslAturPerfCurr15MinUasL PerfCurrentCount, adslAturPerfCurr1DaySesL AdslPerfCurrDayCount, adslAturPerfCurr1DayUasL AdslPerfCurrDayCount, adslAturPerfPrev1DaySesL AdslPerfPrevDayCount, adslAturPerfPrev1DayUasL AdslPerfPrevDayCount } adslAturPerfStatSesL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of severely errored second-line since the last agent reset." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAturPerfDataExtEntry 1 } adslAturPerfStatUasL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reports the count of unavailable seconds-line since the last agent reset." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 2 } adslAturPerfCurr15MinSesL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAturPerfCurr15MinSesL reports the current number of seconds during which there have been severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 3 } adslAturPerfCurr15MinUasL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current 15-minute interval, adslAturPerfCurr15MinUasL reports the current number of seconds during which there have been available seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 4 } adslAturPerfCurr1DaySesL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DaySesL reports the number of seconds during which there have been severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 5 } adslAturPerfCurr1DayUasL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DayUasL reports the number of seconds during which there have been unavailable seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 6 } adslAturPerfPrev1DaySesL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAturPerfPrev1DaySesL reports the number of seconds during which there were severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 7 } adslAturPerfPrev1DayUasL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the previous day, adslAturPerfPrev1DayUasL reports the number of seconds during which there were severely errored seconds-line." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 8 } adslAturIntervalExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATU-R performance data collection interval for ADSL physical interfaces whose IfEntries' ifType is equal to adsl(94)." ::= { adslExtMibObjects 21 } adslAturIntervalExtEntry OBJECT-TYPE SYNTAX AdslAturIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalExtTable." AUGMENTS { adslAturIntervalEntry } ::= { adslAturIntervalExtTable 1 } AdslAturIntervalExtEntry ::= SEQUENCE { adslAturIntervalSesL PerfIntervalCount, adslAturIntervalUasL PerfIntervalCount } adslAturIntervalSesL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line." ::= { adslAturIntervalExtEntry 1 } adslAturIntervalUasL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "For the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line." ::= { adslAturIntervalExtEntry 2 } adslConfProfileExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The adslConfProfileExtTable extends the ADSL line profile configuration information in the adslLineConfProfileTable from the ADSL-LINE-MIB [RFC2662] by adding the ability to configure the ADSL physical line mode." ::= { adslExtMibObjects 22 } adslConfProfileExtEntry OBJECT-TYPE SYNTAX AdslConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineConfProfileEntry defined in [RFC2662]. Each entry corresponds to an ADSL line profile." AUGMENTS { adslLineConfProfileEntry } ::= { adslConfProfileExtTable 1 } AdslConfProfileExtEntry ::= SEQUENCE { adslConfProfileLineType INTEGER } adslConfProfileLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- only fast channel exists interleavedOnly (3), -- only interleaved channel -- exist fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both the fast channel and -- the interleaved channel -- exist } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to configure the ADSL physical line mode. It has following valid values: noChannel(1), when no channels exist. fastOnly(2), when only fast channel exists. interleavedOnly(3), when only interleaved channel exist. fastOrInterleaved(4), when either fast or interleaved channels can exist, but only one at any time. fastAndInterleaved(5), when both the fast channel and the interleaved channel exist. In the case when no value has been set, the default Value is noChannel(1). " DEFVAL { fastOnly } ::= { adslConfProfileExtEntry 1 } adslAlarmConfProfileExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends the adslLineAlarmConfProfileTable and provides threshold parameters for all the counters defined in this MIB module." ::= { adslExtMibObjects 23 } adslAlarmConfProfileExtEntry OBJECT-TYPE SYNTAX AdslAlarmConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineAlarmConfProfileTable defined in [RFC2662]. Each entry corresponds to an ADSL alarm profile." AUGMENTS { adslLineAlarmConfProfileEntry } ::= { adslAlarmConfProfileExtTable 1 } AdslAlarmConfProfileExtEntry ::= SEQUENCE { adslAtucThreshold15MinFailedFastR Integer32, adslAtucThreshold15MinSesL Integer32, adslAtucThreshold15MinUasL Integer32, adslAturThreshold15MinSesL Integer32, adslAturThreshold15MinUasL Integer32 } adslAtucThreshold15MinFailedFastR OBJECT-TYPE SYNTAX Integer32(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The first time the value of the corresponding instance of adslAtucPerfCurr15MinFailedFastR reaches or exceeds this value within a given 15-minute performance data collection period, an adslAtucFailedFastRThreshTrap notification will be generated. The value '0' will disable the notification. The default value of this object is '0'." DEFVAL { 0 } ::= { adslAlarmConfProfileExtEntry 1 } adslAtucThreshold15MinSesL OBJECT-TYPE SYNTAX Integer32(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The first time the value of the corresponding instance of adslAtucPerf15MinSesL reaches or exceeds this value within a given 15-minute performance data collection period, an adslAtucSesLThreshTrap notification will be generated. The value '0' will disable the notification. The default value of this object is '0'." DEFVAL { 0 } ::= { adslAlarmConfProfileExtEntry 2 } adslAtucThreshold15MinUasL OBJECT-TYPE SYNTAX Integer32(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The first time the value of the corresponding instance of adslAtucPerf15MinUasL reaches or exceeds this value within a given 15-minute performance data collection period, an adslAtucUasLThreshTrap notification will be generated. The value '0' will disable the notification. The default value of this object is '0'." DEFVAL { 0 } ::= { adslAlarmConfProfileExtEntry 3 } adslAturThreshold15MinSesL OBJECT-TYPE SYNTAX Integer32(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The first time the value of the corresponding instance of adslAturPerf15MinSesL reaches or exceeds this value within a given 15-minute performance data collection period, an adslAturSesLThreshTrap notification will be generated. The value '0' will disable the notification. The default value of this object is '0'." DEFVAL { 0 } ::= { adslAlarmConfProfileExtEntry 4 } adslAturThreshold15MinUasL OBJECT-TYPE SYNTAX Integer32(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The first time the value of the corresponding instance of adslAturPerf15MinUasL reaches or exceeds this value within a given 15-minute performance data collection period, an adslAturUasLThreshTrap notification will be generated. The value '0' will disable the notification. The default value of this object is '0'." DEFVAL { 0 } ::= { adslAlarmConfProfileExtEntry 5 } -- definitions adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 } adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 } adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 } adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinFailedFastR } STATUS current DESCRIPTION "Failed Fast Retrains 15-minute threshold reached." ::= { adslExtAtucTrapsPrefix 1 } adslAtucSesLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinSesL } STATUS current DESCRIPTION "Severely errored seconds-line 15-minute threshold reached." ::= { adslExtAtucTrapsPrefix 2 } adslAtucUasLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinUasL } STATUS current DESCRIPTION "Unavailable seconds-line 15-minute threshold reached." ::= { adslExtAtucTrapsPrefix 3 } adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 } adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 } adslAturSesLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinSesL } STATUS current DESCRIPTION "Severely errored seconds-line 15-minute threshold reached." ::= { adslExtAturTrapsPrefix 1 } adslAturUasLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinUasL } STATUS current DESCRIPTION "Unavailable seconds-line 15-minute threshold reached." ::= { adslExtAturTrapsPrefix 2 } -- conformance information adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 } adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 } adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 } -- ATU-C agent compliance statements adslExtLineMibAtucCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which represent ADSL ATU-C interfaces." MODULE -- this module MANDATORY-GROUPS { adslExtLineGroup, adslExtLineConfProfileControlGroup, adslExtLineAlarmConfProfileGroup } GROUP adslExtAtucPhysPerfCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslExtAturPhysPerfCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-R physical event counters should implement this group." GROUP adslExtNotificationsGroup DESCRIPTION "This group is optional. Implementations which support TCA (Threshold Crossing Alert) should implement this group." OBJECT adslAtucThreshold15MinFailedFastR MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." OBJECT adslAtucThreshold15MinSesL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." OBJECT adslAtucThreshold15MinUasL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." OBJECT adslAturThreshold15MinSesL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." OBJECT adslAturThreshold15MinUasL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." OBJECT adslLineConfProfileDualLite MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles as defined in ADSL Line MIB [RFC2662] are implemented." ::= { adslExtCompliances 1 } -- units of conformance adslExtLineGroup OBJECT-GROUP OBJECTS { adslLineConfProfileDualLite, adslLineTransAtucCap, adslLineTransAtucConfig, adslLineTransAtucActual, adslLineGlitePowerState } STATUS current DESCRIPTION "A collection of objects providing extended configuration information about an ADSL Line." ::= { adslExtGroups 1 } adslExtAtucPhysPerfCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfStatFastR, adslAtucPerfStatFailedFastR, adslAtucPerfCurr15MinFastR, adslAtucPerfCurr15MinFailedFastR, adslAtucPerfCurr1DayFastR, adslAtucPerfCurr1DayFailedFastR, adslAtucPerfPrev1DayFastR, adslAtucPerfPrev1DayFailedFastR, adslAtucPerfStatSesL, adslAtucPerfStatUasL, adslAtucPerfCurr15MinSesL, adslAtucPerfCurr15MinUasL, adslAtucPerfCurr1DaySesL, adslAtucPerfCurr1DayUasL, adslAtucPerfPrev1DaySesL, adslAtucPerfPrev1DayUasL, adslAtucIntervalFastR, adslAtucIntervalFailedFastR, adslAtucIntervalSesL, adslAtucIntervalUasL } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslExtGroups 2 } adslExtAturPhysPerfCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfStatSesL, adslAturPerfStatUasL, adslAturPerfCurr15MinSesL, adslAturPerfCurr15MinUasL, adslAturPerfCurr1DaySesL, adslAturPerfCurr1DayUasL, adslAturPerfPrev1DaySesL, adslAturPerfPrev1DayUasL, adslAturIntervalSesL, adslAturIntervalUasL } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslExtGroups 3 } adslExtLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslConfProfileLineType } STATUS current DESCRIPTION "A collection of objects providing profile control for the ADSL system." ::= { adslExtGroups 4 } adslExtLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThreshold15MinFailedFastR, adslAtucThreshold15MinSesL, adslAtucThreshold15MinUasL, adslAturThreshold15MinSesL, adslAturThreshold15MinUasL } STATUS current DESCRIPTION "A collection of objects providing alarm profile control for the ADSL system." ::= { adslExtGroups 5 } adslExtNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucFailedFastRThreshTrap, adslAtucSesLThreshTrap, adslAtucUasLThreshTrap, adslAturSesLThreshTrap, adslAturUasLThreshTrap } STATUS current DESCRIPTION "The collection of ADSL extension notifications." ::= { adslExtGroups 6 } END