ADSL-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, NOTIFICATION-TYPE, transmission, Unsigned32 FROM SNMPv2-SMI RowStatus, TruthValue, VariablePointer FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB AdslPerfCurrDayCount, AdslPerfPrevDayCount, AdslPerfTimeElapsed, AdslLineCodingType FROM ADSL-TC-MIB ; adslMIB MODULE-IDENTITY LAST-UPDATED "9908190000Z" ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO " Gregory Bathrick AG Communication Systems A Subsidiary of Lucent Technologies 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-mail: bathricg@agcs.com Faye Ly Copper Mountain Networks Norcal Office 2470 Embarcadero Way Palo Alto, CA 94303 Tel: +1 650-858-8500 Fax: +1 650-858-8085 E-Mail: faye@coppermountain.com (ADSL Forum input only) John Burgess Predictive Systems, Inc. 25A Vreeland Rd. Florham Park, NJ 07932 USA Tel: +1 973-301-5610 Fax: +1 973-301-5699 E-mail: jtburgess@predictive.com IETF ADSL MIB Working Group (adsl@xlist.agcs.com) " DESCRIPTION "The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such line has an entry in an ifTable which may include multiple modem lines. An agent may reside at either end of the ADSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level ADSL line protocol. The agent may monitor and control this protocol for its needs. ADSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus an ADSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to adsl(94), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs-- interval of Seconds in which xxx occurs (e.g., xxx=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks-- Blocks, a data unit, see adslAtuXChanCrcBlockLength " -- Revision history REVISION "9908190000Z" -- 19 August 1999, midnight DESCRIPTION "Initial Version, published as RFC 2662" ::= { transmission 94 } adslLineMib OBJECT IDENTIFIER ::= { adslMIB 1 } adslMibObjects OBJECT IDENTIFIER ::= { adslLineMib 1 } -- objects adslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 1 } adslLineEntry OBJECT-TYPE SYNTAX AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineTable." INDEX { ifIndex } ::= { adslLineTable 1 } AdslLineEntry ::= SEQUENCE { adslLineCoding AdslLineCodingType, adslLineType INTEGER, adslLineSpecific VariablePointer, adslLineConfProfile SnmpAdminString, adslLineAlarmConfProfile SnmpAdminString } adslLineCoding OBJECT-TYPE SYNTAX AdslLineCodingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the ADSL coding type used on this line." ::= { adslLineEntry 1 } adslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- fast channel exists only interleavedOnly (3), -- interleaved channel exists -- only fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both fast or interleaved -- channels exist } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." ::= { adslLineEntry 2 } adslLineSpecific OBJECT-TYPE SYNTAX VariablePointer MAX-ACCESS read-only STATUS current DESCRIPTION "OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM." ::= { adslLineEntry 3 } adslLineConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the configuration profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only." ::= { adslLineEntry 4 } adslLineAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the alarm profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only." ::= { adslLineEntry 5 } adslAtucPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 2 } adslAtucPhysEntry OBJECT-TYPE SYNTAX AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucPhysTable." INDEX { ifIndex } ::= { adslAtucPhysTable 1 } AdslAtucPhysEntry ::= SEQUENCE { adslAtucInvSerialNumber SnmpAdminString, adslAtucInvVendorID SnmpAdminString, adslAtucInvVersionNumber SnmpAdminString, adslAtucCurrSnrMgn INTEGER, adslAtucCurrAtn Gauge32, adslAtucCurrStatus BITS, adslAtucCurrOutputPwr INTEGER, adslAtucCurrAttainableRate Gauge32 } -- inventory group -- -- These items should describe the lowest level identifiable -- component, be it a stand-alone modem, a card in a rack, -- a child-board, etc. -- adslAtucInvSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." ::= { adslAtucPhysEntry 1 } adslAtucInvVendorID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413[10]" ::= { adslAtucPhysEntry 2 } adslAtucInvVersionNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413[10]" ::= { adslAtucPhysEntry 3 } -- current status group -- adslAtucCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER (-640..640) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." ::= { adslAtucPhysEntry 4 } adslAtucCurrAtn OBJECT-TYPE SYNTAX Gauge32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU." ::= { adslAtucPhysEntry 5 } adslAtucCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 } adslAtucCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER (-310..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence." ::= { adslAtucPhysEntry 7 } adslAtucCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAtucPhysEntry 8 } adslAturPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 3 } adslAturPhysEntry OBJECT-TYPE SYNTAX AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturPhysTable." INDEX { ifIndex } ::= { adslAturPhysTable 1 } AdslAturPhysEntry ::= SEQUENCE { adslAturInvSerialNumber SnmpAdminString, adslAturInvVendorID SnmpAdminString, adslAturInvVersionNumber SnmpAdminString, adslAturCurrSnrMgn INTEGER, adslAturCurrAtn Gauge32, adslAturCurrStatus BITS, adslAturCurrOutputPwr INTEGER, adslAturCurrAttainableRate Gauge32 } -- inventory group -- adslAturInvSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." ::= { adslAturPhysEntry 1 } adslAturInvVendorID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413" ::= { adslAturPhysEntry 2 } adslAturInvVersionNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413" ::= { adslAturPhysEntry 3 } -- current status group -- adslAturCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER (-640..640) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." ::= { adslAturPhysEntry 4 } adslAturCurrAtn OBJECT-TYPE SYNTAX Gauge32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU." ::= { adslAturPhysEntry 5 } adslAturCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus." ::= { adslAturPhysEntry 6 } adslAturCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER (-310..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence." ::= { adslAturPhysEntry 7 } adslAturCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAturPhysEntry 8 } adslAtucChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 4 } adslAtucChanEntry OBJECT-TYPE SYNTAX AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucChanTable." INDEX { ifIndex } ::= { adslAtucChanTable 1 } AdslAtucChanEntry ::= SEQUENCE { adslAtucChanInterleaveDelay Gauge32, adslAtucChanCurrTxRate Gauge32, adslAtucChanPrevTxRate Gauge32, adslAtucChanCrcBlockLength Gauge32 } -- current group -- adslAtucChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject." ::= { adslAtucChanEntry 1 } adslAtucChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAtucChanEntry 2 } adslAtucChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAtucChanEntry 3 } adslAtucChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAtucChanEntry 4 } adslAturChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 5 } adslAturChanEntry OBJECT-TYPE SYNTAX AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturChanTable." INDEX { ifIndex } ::= { adslAturChanTable 1 } AdslAturChanEntry ::= SEQUENCE { adslAturChanInterleaveDelay Gauge32, adslAturChanCurrTxRate Gauge32, adslAturChanPrevTxRate Gauge32, adslAturChanCrcBlockLength Gauge32 } -- current group -- adslAturChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject." ::= { adslAturChanEntry 1 } adslAturChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAturChanEntry 2 } adslAturChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAturChanEntry 3 } adslAturChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAturChanEntry 4 } adslAtucPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 6 } adslAtucPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucPerfDataTable." INDEX { ifIndex } ::= { adslAtucPerfDataTable 1 } AdslAtucPerfDataEntry ::= SEQUENCE { adslAtucPerfLofs Counter32, adslAtucPerfLoss Counter32, adslAtucPerfLols Counter32, adslAtucPerfLprs Counter32, adslAtucPerfESs Counter32, adslAtucPerfInits Counter32, adslAtucPerfValidIntervals INTEGER, adslAtucPerfInvalidIntervals INTEGER, adslAtucPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAtucPerfCurr15MinLofs PerfCurrentCount, adslAtucPerfCurr15MinLoss PerfCurrentCount, adslAtucPerfCurr15MinLols PerfCurrentCount, adslAtucPerfCurr15MinLprs PerfCurrentCount, adslAtucPerfCurr15MinESs PerfCurrentCount, adslAtucPerfCurr15MinInits PerfCurrentCount, adslAtucPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAtucPerfCurr1DayLofs AdslPerfCurrDayCount, adslAtucPerfCurr1DayLoss AdslPerfCurrDayCount, adslAtucPerfCurr1DayLols AdslPerfCurrDayCount, adslAtucPerfCurr1DayLprs AdslPerfCurrDayCount, adslAtucPerfCurr1DayESs AdslPerfCurrDayCount, adslAtucPerfCurr1DayInits AdslPerfCurrDayCount, adslAtucPerfPrev1DayMoniSecs INTEGER, adslAtucPerfPrev1DayLofs AdslPerfPrevDayCount, adslAtucPerfPrev1DayLoss AdslPerfPrevDayCount, adslAtucPerfPrev1DayLols AdslPerfPrevDayCount, adslAtucPerfPrev1DayLprs AdslPerfPrevDayCount, adslAtucPerfPrev1DayESs AdslPerfPrevDayCount, adslAtucPerfPrev1DayInits AdslPerfPrevDayCount } -- Event Counters -- -- Also see adslAtucIntervalTable for 15 minute interval -- elapsed counters. -- adslAtucPerfLofs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAtucPerfDataEntry 1 } adslAtucPerfLoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAtucPerfDataEntry 2 } adslAtucPerfLols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Link failures since agent reset." ::= { adslAtucPerfDataEntry 3 } adslAtucPerfLprs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAtucPerfDataEntry 4 } adslAtucPerfESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 5 } adslAtucPerfInits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since agent reset. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 6 } -- general 15 min interval information -- adslAtucPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAtucPerfDataEntry 7 } adslAtucPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAtucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAtucPerfDataEntry 8 } -- 15 min current performance group -- adslAtucPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAtucPerfDataEntry 9 } adslAtucPerfCurr15MinLofs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAtucPerfDataEntry 10 } adslAtucPerfCurr15MinLoss OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAtucPerfDataEntry 11 } adslAtucPerfCurr15MinLols OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Link." ::= { adslAtucPerfDataEntry 12 } adslAtucPerfCurr15MinLprs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAtucPerfDataEntry 13 } adslAtucPerfCurr15MinESs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 14 } adslAtucPerfCurr15MinInits OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 15 } -- 1-day current and previous performance group -- adslAtucPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucPerfDataEntry 16 } adslAtucPerfCurr1DayLofs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 17 } adslAtucPerfCurr1DayLoss OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 18 } adslAtucPerfCurr1DayLols OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 19 } adslAtucPerfCurr1DayLprs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 20 } adslAtucPerfCurr1DayESs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 21 } adslAtucPerfCurr1DayInits OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 22 } adslAtucPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAtucPerfDataEntry 23 } adslAtucPerfPrev1DayLofs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 24 } adslAtucPerfPrev1DayLoss OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 25 } adslAtucPerfPrev1DayLols OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 26 } adslAtucPerfPrev1DayLprs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 27 } adslAtucPerfPrev1DayESs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 28 } adslAtucPerfPrev1DayInits OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 29 } adslAturPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 7 } adslAturPerfDataEntry OBJECT-TYPE SYNTAX AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturPerfDataTable." INDEX { ifIndex } ::= { adslAturPerfDataTable 1 } AdslAturPerfDataEntry ::= SEQUENCE { adslAturPerfLofs Counter32, adslAturPerfLoss Counter32, adslAturPerfLprs Counter32, adslAturPerfESs Counter32, adslAturPerfValidIntervals INTEGER, adslAturPerfInvalidIntervals INTEGER, adslAturPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAturPerfCurr15MinLofs PerfCurrentCount, adslAturPerfCurr15MinLoss PerfCurrentCount, adslAturPerfCurr15MinLprs PerfCurrentCount, adslAturPerfCurr15MinESs PerfCurrentCount, adslAturPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAturPerfCurr1DayLofs AdslPerfCurrDayCount, adslAturPerfCurr1DayLoss AdslPerfCurrDayCount, adslAturPerfCurr1DayLprs AdslPerfCurrDayCount, adslAturPerfCurr1DayESs AdslPerfCurrDayCount, adslAturPerfPrev1DayMoniSecs INTEGER, adslAturPerfPrev1DayLofs AdslPerfPrevDayCount, adslAturPerfPrev1DayLoss AdslPerfPrevDayCount, adslAturPerfPrev1DayLprs AdslPerfPrevDayCount, adslAturPerfPrev1DayESs AdslPerfPrevDayCount } -- Event (Raw) Counters -- -- Also see adslAturIntervalTable for 15 minute interval -- elapsed counters. -- adslAturPerfLofs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAturPerfDataEntry 1 } adslAturPerfLoss OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAturPerfDataEntry 2 } adslAturPerfLprs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAturPerfDataEntry 3 } adslAturPerfESs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 4 } -- general 15 min interval information -- adslAturPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAturPerfDataEntry 5 } adslAturPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAturPerfDataEntry 6 } -- 15 min current performance group -- adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAturPerfDataEntry 7 } adslAturPerfCurr15MinLofs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAturPerfDataEntry 8 } adslAturPerfCurr15MinLoss OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAturPerfDataEntry 9 } adslAturPerfCurr15MinLprs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAturPerfDataEntry 10 } adslAturPerfCurr15MinESs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturPerfDataEntry 12 } adslAturPerfCurr1DayLofs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 13 } adslAturPerfCurr1DayLoss OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 14 } adslAturPerfCurr1DayLprs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 15 } adslAturPerfCurr1DayESs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 16 } adslAturPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAturPerfDataEntry 17 } adslAturPerfPrev1DayLofs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 18 } adslAturPerfPrev1DayLoss OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 19 } adslAturPerfPrev1DayLprs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 20 } adslAturPerfPrev1DayESs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 21 } adslAtucIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 8 } adslAtucIntervalEntry OBJECT-TYPE SYNTAX AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucIntervalNumber } ::= { adslAtucIntervalTable 1 } AdslAtucIntervalEntry ::= SEQUENCE { adslAtucIntervalNumber INTEGER, adslAtucIntervalLofs PerfIntervalCount, adslAtucIntervalLoss PerfIntervalCount, adslAtucIntervalLols PerfIntervalCount, adslAtucIntervalLprs PerfIntervalCount, adslAtucIntervalESs PerfIntervalCount, adslAtucIntervalInits PerfIntervalCount, adslAtucIntervalValidData TruthValue } adslAtucIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAtucIntervalEntry 1 } adslAtucIntervalLofs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAtucIntervalEntry 2 } adslAtucIntervalLoss OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAtucIntervalEntry 3 } adslAtucIntervalLols OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { adslAtucIntervalEntry 4 } adslAtucIntervalLprs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAtucIntervalEntry 5 } adslAtucIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucIntervalEntry 6 } adslAtucIntervalInits OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during the interval. Includes both successful and failed attempts." ::= { adslAtucIntervalEntry 7 } adslAtucIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAtucIntervalEntry 8 } adslAturIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 9 } adslAturIntervalEntry OBJECT-TYPE SYNTAX AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturIntervalNumber } ::= { adslAturIntervalTable 1 } AdslAturIntervalEntry ::= SEQUENCE { adslAturIntervalNumber INTEGER, adslAturIntervalLofs PerfIntervalCount, adslAturIntervalLoss PerfIntervalCount, adslAturIntervalLprs PerfIntervalCount, adslAturIntervalESs PerfIntervalCount, adslAturIntervalValidData TruthValue } adslAturIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAturIntervalEntry 1 } adslAturIntervalLofs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAturIntervalEntry 2 } adslAturIntervalLoss OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAturIntervalEntry 3 } adslAturIntervalLprs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAturIntervalEntry 4 } adslAturIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturIntervalEntry 5 } adslAturIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAturIntervalEntry 6 } adslAtucChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 10 } adslAtucChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucChanPerfDataTable." INDEX { ifIndex } ::= { adslAtucChanPerfDataTable 1 } AdslAtucChanPerfDataEntry ::= SEQUENCE { adslAtucChanReceivedBlks Counter32, adslAtucChanTransmittedBlks Counter32, adslAtucChanCorrectedBlks Counter32, adslAtucChanUncorrectBlks Counter32, adslAtucChanPerfValidIntervals INTEGER, adslAtucChanPerfInvalidIntervals INTEGER, adslAtucChanPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinTransmittedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinCorrectedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinUncorrectBlks PerfCurrentCount, adslAtucChanPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayTransmittedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayCorrectedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayUncorrectBlks AdslPerfCurrDayCount, adslAtucChanPerfPrev1DayMoniSecs INTEGER, adslAtucChanPerfPrev1DayReceivedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayTransmittedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayCorrectedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayUncorrectBlks AdslPerfPrevDayCount } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAtucChanCrcBlockLength for more information. -- adslAtucChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 1 } adslAtucChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 2 } adslAtucChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAtucChanPerfDataEntry 3 } adslAtucChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAtucChanPerfDataEntry 4 } -- general 15 min interval information -- adslAtucChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAtucChanPerfDataEntry 5 } adslAtucChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAtucChanPerfDataEntry 6 } -- 15 min current performance group -- adslAtucChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAtucChanPerfDataEntry 7 } adslAtucChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 8 } adslAtucChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 9 } adslAtucChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 10 } adslAtucChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAtucChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucChanPerfDataEntry 12 } adslAtucChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 13 } adslAtucChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 14 } adslAtucChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 15 } adslAtucChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 16 } adslAtucChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAtucChanPerfDataEntry 17 } adslAtucChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 18 } adslAtucChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 19 } adslAtucChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 20 } adslAtucChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 21 } adslAturChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 11 } adslAturChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturChanPerfDataTable." INDEX { ifIndex } ::= { adslAturChanPerfDataTable 1 } AdslAturChanPerfDataEntry ::= SEQUENCE { adslAturChanReceivedBlks Counter32, adslAturChanTransmittedBlks Counter32, adslAturChanCorrectedBlks Counter32, adslAturChanUncorrectBlks Counter32, adslAturChanPerfValidIntervals INTEGER, adslAturChanPerfInvalidIntervals INTEGER, adslAturChanPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks PerfCurrentCount, adslAturChanPerfCurr15MinTransmittedBlks PerfCurrentCount, adslAturChanPerfCurr15MinCorrectedBlks PerfCurrentCount, adslAturChanPerfCurr15MinUncorrectBlks PerfCurrentCount, adslAturChanPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayTransmittedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayCorrectedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayUncorrectBlks AdslPerfCurrDayCount, adslAturChanPerfPrev1DayMoniSecs INTEGER, adslAturChanPerfPrev1DayReceivedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayTransmittedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayCorrectedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayUncorrectBlks AdslPerfPrevDayCount } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAturChanCrcBlockLength for more information. -- adslAturChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAturChanPerfDataEntry 1 } adslAturChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAturChanPerfDataEntry 2 } adslAturChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAturChanPerfDataEntry 3 } adslAturChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAturChanPerfDataEntry 4 } -- general 15 min interval information -- adslAturChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAturChanPerfDataEntry 5 } adslAturChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAturChanPerfDataEntry 6 } -- 15 min current performance group -- adslAturChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturChanPerfDataEntry 7 } adslAturChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 8 } adslAturChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 9 } adslAturChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 10 } adslAturChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturChanPerfDataEntry 12 } adslAturChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 13 } adslAturChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 14 } adslAturChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 15 } adslAturChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 16 } adslAturChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAturChanPerfDataEntry 17 } adslAturChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 18 } adslAturChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 19 } adslAturChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 20 } adslAturChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 21 } adslAtucChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 12 } adslAtucChanIntervalEntry OBJECT-TYPE SYNTAX AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucChanIntervalNumber } ::= { adslAtucChanIntervalTable 1 } AdslAtucChanIntervalEntry ::= SEQUENCE { adslAtucChanIntervalNumber INTEGER, adslAtucChanIntervalReceivedBlks PerfIntervalCount, adslAtucChanIntervalTransmittedBlks PerfIntervalCount, adslAtucChanIntervalCorrectedBlks PerfIntervalCount, adslAtucChanIntervalUncorrectBlks PerfIntervalCount, adslAtucChanIntervalValidData TruthValue } adslAtucChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAtucChanIntervalEntry 1 } adslAtucChanIntervalReceivedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAtucChanIntervalEntry 2 } adslAtucChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAtucChanIntervalEntry 3 } adslAtucChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAtucChanIntervalEntry 4 } adslAtucChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAtucChanIntervalEntry 5 } adslAtucChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAtucChanIntervalEntry 6 } adslAturChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 13 } adslAturChanIntervalEntry OBJECT-TYPE SYNTAX AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturChanIntervalNumber } ::= { adslAturChanIntervalTable 1 } AdslAturChanIntervalEntry ::= SEQUENCE { adslAturChanIntervalNumber INTEGER, adslAturChanIntervalReceivedBlks PerfIntervalCount, adslAturChanIntervalTransmittedBlks PerfIntervalCount, adslAturChanIntervalCorrectedBlks PerfIntervalCount, adslAturChanIntervalUncorrectBlks PerfIntervalCount, adslAturChanIntervalValidData TruthValue } adslAturChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAturChanIntervalEntry 1 } adslAturChanIntervalReceivedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAturChanIntervalEntry 2 } adslAturChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAturChanIntervalEntry 3 } adslAturChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAturChanIntervalEntry 4 } adslAturChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAturChanIntervalEntry 5 } adslAturChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAturChanIntervalEntry 6 } -- Profile Group -- adslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line." ::= { adslMibObjects 14} adslLineConfProfileEntry OBJECT-TYPE SYNTAX AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index. " INDEX { IMPLIED adslLineConfProfileName} ::= { adslLineConfProfileTable 1} AdslLineConfProfileEntry ::= SEQUENCE { adslLineConfProfileName SnmpAdminString, adslAtucConfRateMode INTEGER, adslAtucConfRateChanRatio INTEGER, adslAtucConfTargetSnrMgn INTEGER, adslAtucConfMaxSnrMgn INTEGER, adslAtucConfMinSnrMgn INTEGER, adslAtucConfDownshiftSnrMgn INTEGER, adslAtucConfUpshiftSnrMgn INTEGER, adslAtucConfMinUpshiftTime INTEGER, adslAtucConfMinDownshiftTime INTEGER, adslAtucChanConfFastMinTxRate Unsigned32, adslAtucChanConfInterleaveMinTxRate Unsigned32, adslAtucChanConfFastMaxTxRate Unsigned32, adslAtucChanConfInterleaveMaxTxRate Unsigned32, adslAtucChanConfMaxInterleaveDelay INTEGER, adslAturConfRateMode INTEGER, adslAturConfRateChanRatio INTEGER, adslAturConfTargetSnrMgn INTEGER, adslAturConfMaxSnrMgn INTEGER, adslAturConfMinSnrMgn INTEGER, adslAturConfDownshiftSnrMgn INTEGER, adslAturConfUpshiftSnrMgn INTEGER, adslAturConfMinUpshiftTime INTEGER, adslAturConfMinDownshiftTime INTEGER, adslAturChanConfFastMinTxRate Unsigned32, adslAturChanConfInterleaveMinTxRate Unsigned32, adslAturChanConfFastMaxTxRate Unsigned32, adslAturChanConfInterleaveMaxTxRate Unsigned32, adslAturChanConfMaxInterleaveDelay INTEGER, adslLineConfProfileRowStatus RowStatus } adslLineConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'." ::= { adslLineConfProfileEntry 1 } adslAtucConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 2 } adslAtucConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAtucConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 3 } adslAtucConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 4 } adslAtucConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 5 } adslAtucConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 6 } adslAtucConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 7 } adslAtucConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 8 } adslAtucConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 9 } adslAtucConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 10 } adslAtucChanConfFastMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 11 } adslAtucChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates." ::= { adslLineConfProfileEntry 12 } adslAtucChanConfFastMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 13 } adslAtucChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 14 } adslAtucChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 15 } adslAturConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 16 } adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 } adslAturConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 18 } adslAturConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 19 } adslAturConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 20 } adslAturConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 21 } adslAturConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 22 } adslAturConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 23 } adslAturConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 24 } adslAturChanConfFastMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 25 } adslAturChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 26 } adslAturChanConfFastMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 27 } adslAturChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 28 } adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 } adslLineConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'." ::= { adslLineConfProfileEntry 30 } adslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line" ::= { adslMibObjects 15} adslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index. " INDEX { IMPLIED adslLineAlarmConfProfileName} ::= { adslLineAlarmConfProfileTable 1} AdslLineAlarmConfProfileEntry ::= SEQUENCE { adslLineAlarmConfProfileName SnmpAdminString, adslAtucThresh15MinLofs INTEGER, adslAtucThresh15MinLoss INTEGER, adslAtucThresh15MinLols INTEGER, adslAtucThresh15MinLprs INTEGER, adslAtucThresh15MinESs INTEGER, adslAtucThreshFastRateUp Unsigned32, adslAtucThreshInterleaveRateUp Unsigned32, adslAtucThreshFastRateDown Unsigned32, adslAtucThreshInterleaveRateDown Unsigned32, adslAtucInitFailureTrapEnable INTEGER, adslAturThresh15MinLofs INTEGER, adslAturThresh15MinLoss INTEGER, adslAturThresh15MinLprs INTEGER, adslAturThresh15MinESs INTEGER, adslAturThreshFastRateUp Unsigned32, adslAturThreshInterleaveRateUp Unsigned32, adslAturThreshFastRateDown Unsigned32, adslAturThreshInterleaveRateDown Unsigned32, adslLineAlarmConfProfileRowStatus RowStatus } adslLineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line alarm configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'." ::= { adslLineAlarmConfProfileEntry 1} adslAtucThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 2} adslAtucThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 3} adslAtucThresh15MinLols OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 4} adslAtucThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 5} adslAtucThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 6} adslAtucThreshFastRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 7} adslAtucThreshInterleaveRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 8} adslAtucThreshFastRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 9 } adslAtucThreshInterleaveRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 10 } adslAtucInitFailureTrapEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enables and disables the InitFailureTrap. This object is defaulted disable(2)." DEFVAL { disable } ::= { adslLineAlarmConfProfileEntry 11 } adslAturThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 12 } adslAturThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 13 } adslAturThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 14 } adslAturThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 15 } adslAturThreshFastRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 16 } adslAturThreshInterleaveRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 17 } adslAturThreshFastRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 18 } adslAturThreshInterleaveRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 19 } adslLineAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'." ::= { adslLineAlarmConfProfileEntry 20 } -- Line Code Specific Tables -- These are place holders for the Line Code Specific MIBs -- once they become available. adslLCSMib OBJECT IDENTIFIER ::= { adslMibObjects 16 } -- trap definitions adslTraps OBJECT IDENTIFIER ::= { adslLineMib 2 } adslAtucTraps OBJECT IDENTIFIER ::= { adslTraps 1 } adslAtucPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLofs, adslAtucThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold reached." ::= { adslAtucTraps 0 1 } adslAtucPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLoss, adslAtucThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold reached." ::= { adslAtucTraps 0 2 } adslAtucPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLprs, adslAtucThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold reached." ::= { adslAtucTraps 0 3 } adslAtucPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinESs, adslAtucThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold reached." ::= { adslAtucTraps 0 4 } adslAtucRateChangeTrap NOTIFICATION-TYPE OBJECTS { adslAtucChanCurrTxRate, adslAtucChanPrevTxRate } STATUS current DESCRIPTION "The ATUCs transmit rate has changed (RADSL mode only)" ::= { adslAtucTraps 0 5 } adslAtucPerfLolsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLols, adslAtucThresh15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold reached." ::= { adslAtucTraps 0 6 } adslAtucInitFailureTrap NOTIFICATION-TYPE OBJECTS { adslAtucCurrStatus } STATUS current DESCRIPTION "ATUC initialization failed. See adslAtucCurrStatus for potential reasons." ::= { adslAtucTraps 0 7 } adslAturTraps OBJECT IDENTIFIER ::= { adslTraps 2 } adslAturPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLofs, adslAturThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold reached." ::= { adslAturTraps 0 1 } adslAturPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLoss, adslAturThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold reached." ::= { adslAturTraps 0 2 } adslAturPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLprs, adslAturThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold reached." ::= { adslAturTraps 0 3 } adslAturPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinESs, adslAturThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold reached." ::= { adslAturTraps 0 4 } adslAturRateChangeTrap NOTIFICATION-TYPE OBJECTS { adslAturChanCurrTxRate, adslAturChanPrevTxRate } STATUS current DESCRIPTION "The ATURs transmit rate has changed (RADSL mode only)" ::= { adslAturTraps 0 5 } -- no adslAturPerfLolsThreshTrap possible { 0 6 } -- no adslAturInitFailureTrap possible { 0 7 } -- conformance information adslConformance OBJECT IDENTIFIER ::= { adslLineMib 3 } adslGroups OBJECT IDENTIFIER ::= { adslConformance 1 } adslCompliances OBJECT IDENTIFIER ::= { adslConformance 2 } -- ATU-C agent compliance statements adslLineMibAtucCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage ADSL ATU-C interfaces." MODULE -- this module MANDATORY-GROUPS { adslLineGroup, adslPhysicalGroup, adslChannelGroup, adslAtucPhysPerfIntervalGroup, adslAturPhysPerfIntervalGroup, adslLineConfProfileGroup, adslLineAlarmConfProfileGroup, adslLineConfProfileControlGroup } GROUP adslAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-R physical event counters should implement this group." GROUP adslAtucChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-C channel block event counters should implement this group." GROUP adslAturChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-R channel block event counters should implement this group." OBJECT adslLineConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable when static profiles are implemented." OBJECT adslAtucConfRateMode MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfRateChanRatio MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfTargetSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMaxSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfDownshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfUpshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinUpshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinDownshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfFastMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfInterleaveMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfFastMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfInterleaveMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfMaxInterleaveDelay MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfRateMode MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfRateChanRatio MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfTargetSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMaxSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMinSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfDownshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfUpshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMinUpshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMinDownshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfFastMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfInterleaveMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfFastMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfInterleaveMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfMaxInterleaveDelay MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslLineAlarmConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslAtucThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLols MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucInitFailureTrapEnable MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineAlarmConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." ::= { adslCompliances 1 } -- ATU-R agent compliance statements adslLineMibAturCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage ADSL ATU-R interfaces." MODULE -- this module MANDATORY-GROUPS { adslAturLineGroup, adslAturPhysicalGroup, adslAturChannelGroup, adslAturAtucPhysPerfIntervalGroup, adslAturAturPhysPerfIntervalGroup, adslAturLineAlarmConfProfileGroup, adslAturLineConfProfileControlGroup } GROUP adslAturAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslAturAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-R physical event counters should implement this group." GROUP adslAturAtucChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-C channel block event counters should implement this group." GROUP adslAturAturChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-R channel block event counters should implement this group." OBJECT adslLineAlarmConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslAtucThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucInitFailureTrapEnable MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineAlarmConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslAtucCurrStatus SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2) } DESCRIPTION "It is allowable to implement only noDefect(0), lossOfFraming(1) and lossOfSignal(2) by the ATU-R agent." ::= { adslCompliances 2 } -- units of conformance adslLineGroup OBJECT-GROUP OBJECTS { adslLineCoding, adslLineType, adslLineSpecific } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line." ::= { adslGroups 1 } adslPhysicalGroup OBJECT-GROUP OBJECTS { adslAtucInvSerialNumber, adslAtucInvVendorID, adslAtucInvVersionNumber, adslAtucCurrSnrMgn, adslAtucCurrAtn, adslAtucCurrStatus, adslAtucCurrOutputPwr, adslAtucCurrAttainableRate, adslAturInvSerialNumber, adslAturInvVendorID, adslAturInvVersionNumber, adslAturCurrSnrMgn, adslAturCurrAtn, adslAturCurrStatus, adslAturCurrOutputPwr, adslAturCurrAttainableRate } STATUS current DESCRIPTION "A collection of objects providing physical configuration information of the ADSL Line." ::= { adslGroups 2 } adslChannelGroup OBJECT-GROUP OBJECTS { adslAtucChanInterleaveDelay, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate, adslAtucChanCrcBlockLength, adslAturChanInterleaveDelay, adslAturChanCurrTxRate, adslAturChanPrevTxRate, adslAturChanCrcBlockLength } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL channel." ::= { adslGroups 3 } adslAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfLofs, adslAtucPerfLoss, adslAtucPerfLols, adslAtucPerfLprs, adslAtucPerfESs, adslAtucPerfInits } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslGroups 4 } adslAtucPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAtucPerfValidIntervals, adslAtucPerfInvalidIntervals, adslAtucPerfCurr15MinTimeElapsed, adslAtucPerfCurr15MinLofs, adslAtucPerfCurr15MinLoss, adslAtucPerfCurr15MinLols, adslAtucPerfCurr15MinLprs, adslAtucPerfCurr15MinESs, adslAtucPerfCurr15MinInits, adslAtucPerfCurr1DayLofs, adslAtucPerfCurr1DayLoss, adslAtucPerfCurr1DayLols, adslAtucPerfCurr1DayLprs, adslAtucPerfCurr1DayESs, adslAtucPerfCurr1DayInits, adslAtucPerfPrev1DayMoniSecs, adslAtucPerfPrev1DayLofs, adslAtucPerfPrev1DayLoss, adslAtucPerfPrev1DayLols, adslAtucPerfPrev1DayLprs, adslAtucPerfPrev1DayESs, adslAtucPerfPrev1DayInits, adslAtucIntervalLofs, adslAtucIntervalLoss, adslAtucIntervalLols, adslAtucIntervalLprs, adslAtucIntervalESs, adslAtucIntervalInits, adslAtucIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) ." ::= { adslGroups 5 } adslAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfLofs, adslAturPerfLoss, adslAturPerfLprs, adslAturPerfESs } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-R end)." ::= { adslGroups 6 } adslAturPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAturPerfValidIntervals, adslAturPerfInvalidIntervals, adslAturPerfCurr15MinTimeElapsed, adslAturPerfCurr15MinLofs, adslAturPerfCurr15MinLoss, adslAturPerfCurr15MinLprs, adslAturPerfCurr15MinESs, adslAturPerfCurr1DayTimeElapsed, adslAturPerfCurr1DayLofs, adslAturPerfCurr1DayLoss, adslAturPerfCurr1DayLprs, adslAturPerfCurr1DayESs, adslAturPerfPrev1DayMoniSecs, adslAturPerfPrev1DayLofs, adslAturPerfPrev1DayLoss, adslAturPerfPrev1DayLprs, adslAturPerfPrev1DayESs, adslAturIntervalLofs, adslAturIntervalLoss, adslAturIntervalLprs, adslAturIntervalESs, adslAturIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end)." ::= { adslGroups 7 } adslAtucChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAtucChanReceivedBlks, adslAtucChanTransmittedBlks, adslAtucChanCorrectedBlks, adslAtucChanUncorrectBlks, adslAtucChanPerfValidIntervals, adslAtucChanPerfInvalidIntervals, adslAtucChanPerfCurr15MinTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks, adslAtucChanPerfCurr15MinTransmittedBlks, adslAtucChanPerfCurr15MinCorrectedBlks, adslAtucChanPerfCurr15MinUncorrectBlks, adslAtucChanPerfCurr1DayTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks, adslAtucChanPerfCurr1DayTransmittedBlks, adslAtucChanPerfCurr1DayCorrectedBlks, adslAtucChanPerfCurr1DayUncorrectBlks, adslAtucChanPerfPrev1DayMoniSecs, adslAtucChanPerfPrev1DayReceivedBlks, adslAtucChanPerfPrev1DayTransmittedBlks, adslAtucChanPerfPrev1DayCorrectedBlks, adslAtucChanPerfPrev1DayUncorrectBlks, adslAtucChanIntervalReceivedBlks, adslAtucChanIntervalTransmittedBlks, adslAtucChanIntervalCorrectedBlks, adslAtucChanIntervalUncorrectBlks, adslAtucChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 8 } adslAturChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAturChanReceivedBlks, adslAturChanTransmittedBlks, adslAturChanCorrectedBlks, adslAturChanUncorrectBlks, adslAturChanPerfValidIntervals, adslAturChanPerfInvalidIntervals, adslAturChanPerfCurr15MinTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks, adslAturChanPerfCurr15MinTransmittedBlks, adslAturChanPerfCurr15MinCorrectedBlks, adslAturChanPerfCurr15MinUncorrectBlks, adslAturChanPerfCurr1DayTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks, adslAturChanPerfCurr1DayTransmittedBlks, adslAturChanPerfCurr1DayCorrectedBlks, adslAturChanPerfCurr1DayUncorrectBlks, adslAturChanPerfPrev1DayMoniSecs, adslAturChanPerfPrev1DayReceivedBlks, adslAturChanPerfPrev1DayTransmittedBlks, adslAturChanPerfPrev1DayCorrectedBlks, adslAturChanPerfPrev1DayUncorrectBlks, adslAturChanIntervalReceivedBlks, adslAturChanIntervalTransmittedBlks, adslAturChanIntervalCorrectedBlks, adslAturChanIntervalUncorrectBlks, adslAturChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 9 } adslLineConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucConfRateMode, adslAtucConfRateChanRatio, adslAtucConfTargetSnrMgn, adslAtucConfMaxSnrMgn, adslAtucConfMinSnrMgn, adslAtucConfDownshiftSnrMgn, adslAtucConfUpshiftSnrMgn, adslAtucConfMinUpshiftTime, adslAtucConfMinDownshiftTime, adslAtucChanConfFastMinTxRate, adslAtucChanConfInterleaveMinTxRate, adslAtucChanConfFastMaxTxRate, adslAtucChanConfInterleaveMaxTxRate, adslAtucChanConfMaxInterleaveDelay, adslAturConfRateMode, adslAturConfRateChanRatio, adslAturConfTargetSnrMgn, adslAturConfMaxSnrMgn, adslAturConfMinSnrMgn, adslAturConfDownshiftSnrMgn, adslAturConfUpshiftSnrMgn, adslAturConfMinUpshiftTime, adslAturConfMinDownshiftTime, adslAturChanConfFastMinTxRate, adslAturChanConfInterleaveMinTxRate, adslAturChanConfFastMaxTxRate, adslAturChanConfInterleaveMaxTxRate, adslAturChanConfMaxInterleaveDelay } STATUS current DESCRIPTION "A collection of objects providing provisioning information about an ADSL Line." ::= { adslGroups 10 } adslLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThresh15MinLofs, adslAtucThresh15MinLoss, adslAtucThresh15MinLols, adslAtucThresh15MinLprs, adslAtucThresh15MinESs, adslAtucThreshFastRateUp, adslAtucThreshInterleaveRateUp, adslAtucThreshFastRateDown, adslAtucThreshInterleaveRateDown, adslAtucInitFailureTrapEnable, adslAturThresh15MinLofs, adslAturThresh15MinLoss, adslAturThresh15MinLprs, adslAturThresh15MinESs, adslAturThreshFastRateUp, adslAturThreshInterleaveRateUp, adslAturThreshFastRateDown, adslAturThreshInterleaveRateDown } STATUS current DESCRIPTION "A collection of objects providing alarm provisioning information about an ADSL Line." ::= { adslGroups 11 } adslLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslLineConfProfile, adslLineAlarmConfProfile, adslLineConfProfileRowStatus, adslLineAlarmConfProfileRowStatus } STATUS current DESCRIPTION "A collection of objects providing profile control for the ADSL system." ::= { adslGroups 12 } adslNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucPerfLofsThreshTrap, adslAtucPerfLossThreshTrap, adslAtucPerfLprsThreshTrap, adslAtucPerfESsThreshTrap, adslAtucRateChangeTrap, adslAtucPerfLolsThreshTrap, adslAtucInitFailureTrap, adslAturPerfLofsThreshTrap, adslAturPerfLossThreshTrap, adslAturPerfLprsThreshTrap, adslAturPerfESsThreshTrap, adslAturRateChangeTrap } STATUS current DESCRIPTION "The collection of adsl notifications." ::= { adslGroups 13 } -- units of conformance for ATU-R agent adslAturLineGroup OBJECT-GROUP OBJECTS { adslLineCoding } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line on the ATU-R side." ::= { adslGroups 14 } adslAturPhysicalGroup OBJECT-GROUP OBJECTS { adslAtucInvVendorID, adslAtucInvVersionNumber, adslAtucCurrOutputPwr, adslAtucCurrAttainableRate, adslAturInvSerialNumber, adslAturInvVendorID, adslAturInvVersionNumber, adslAturCurrSnrMgn, adslAturCurrAtn, adslAturCurrStatus, adslAturCurrOutputPwr, adslAturCurrAttainableRate, adslAtucCurrStatus } STATUS current DESCRIPTION "A collection of objects providing physical configuration information of the ADSL Line on the ATU-R side." ::= { adslGroups 15 } adslAturChannelGroup OBJECT-GROUP OBJECTS { adslAtucChanInterleaveDelay, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate, adslAturChanInterleaveDelay, adslAturChanCurrTxRate, adslAturChanPrevTxRate, adslAturChanCrcBlockLength } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL channel on the ATU-R side." ::= { adslGroups 16 } adslAturAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfLofs, adslAtucPerfLoss, adslAtucPerfESs, adslAtucPerfInits } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 17 } adslAturAtucPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAtucPerfValidIntervals, adslAtucPerfInvalidIntervals, adslAtucPerfCurr15MinTimeElapsed, adslAtucPerfCurr15MinLofs, adslAtucPerfCurr15MinLoss, adslAtucPerfCurr15MinESs, adslAtucPerfCurr15MinInits, adslAtucPerfCurr1DayTimeElapsed, adslAtucPerfCurr1DayLofs, adslAtucPerfCurr1DayLoss, adslAtucPerfCurr1DayESs, adslAtucPerfCurr1DayInits, adslAtucPerfPrev1DayMoniSecs, adslAtucPerfPrev1DayLofs, adslAtucPerfPrev1DayLoss, adslAtucPerfPrev1DayESs, adslAtucPerfPrev1DayInits, adslAtucIntervalLofs, adslAtucIntervalLoss, adslAtucIntervalESs, adslAtucIntervalInits, adslAtucIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 18 } adslAturAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfLofs, adslAturPerfLoss, adslAturPerfLprs, adslAturPerfESs } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 19 } adslAturAturPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAturPerfValidIntervals, adslAturPerfInvalidIntervals, adslAturPerfCurr15MinTimeElapsed, adslAturPerfCurr15MinLofs, adslAturPerfCurr15MinLoss, adslAturPerfCurr15MinLprs, adslAturPerfCurr15MinESs, adslAturPerfCurr1DayTimeElapsed, adslAturPerfCurr1DayLofs, adslAturPerfCurr1DayLoss, adslAturPerfCurr1DayLprs, adslAturPerfCurr1DayESs, adslAturPerfPrev1DayMoniSecs, adslAturPerfPrev1DayLofs, adslAturPerfPrev1DayLoss, adslAturPerfPrev1DayLprs, adslAturPerfPrev1DayESs, adslAturIntervalLofs, adslAturIntervalLoss, adslAturIntervalLprs, adslAturIntervalESs, adslAturIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 20 } adslAturAtucChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAtucChanReceivedBlks, adslAtucChanTransmittedBlks, adslAtucChanCorrectedBlks, adslAtucChanUncorrectBlks, adslAtucChanPerfCurr15MinTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks, adslAtucChanPerfCurr15MinTransmittedBlks, adslAtucChanPerfCurr15MinCorrectedBlks, adslAtucChanPerfCurr15MinUncorrectBlks, adslAtucChanPerfCurr1DayTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks, adslAtucChanPerfCurr1DayTransmittedBlks, adslAtucChanPerfCurr1DayCorrectedBlks, adslAtucChanPerfCurr1DayUncorrectBlks, adslAtucChanPerfPrev1DayMoniSecs, adslAtucChanPerfPrev1DayReceivedBlks, adslAtucChanPerfPrev1DayTransmittedBlks, adslAtucChanPerfPrev1DayCorrectedBlks, adslAtucChanPerfPrev1DayUncorrectBlks, adslAtucChanPerfValidIntervals, adslAtucChanPerfInvalidIntervals, adslAtucChanIntervalReceivedBlks, adslAtucChanIntervalTransmittedBlks, adslAtucChanIntervalCorrectedBlks, adslAtucChanIntervalUncorrectBlks, adslAtucChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 21 } adslAturAturChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAturChanReceivedBlks, adslAturChanTransmittedBlks, adslAturChanCorrectedBlks, adslAturChanUncorrectBlks, adslAturChanPerfValidIntervals, adslAturChanPerfInvalidIntervals, adslAturChanPerfCurr15MinTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks, adslAturChanPerfCurr15MinTransmittedBlks, adslAturChanPerfCurr15MinCorrectedBlks, adslAturChanPerfCurr15MinUncorrectBlks, adslAturChanPerfCurr1DayTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks, adslAturChanPerfCurr1DayTransmittedBlks, adslAturChanPerfCurr1DayCorrectedBlks, adslAturChanPerfCurr1DayUncorrectBlks, adslAturChanPerfPrev1DayMoniSecs, adslAturChanPerfPrev1DayReceivedBlks, adslAturChanPerfPrev1DayTransmittedBlks, adslAturChanPerfPrev1DayCorrectedBlks, adslAturChanPerfPrev1DayUncorrectBlks, adslAturChanIntervalReceivedBlks, adslAturChanIntervalTransmittedBlks, adslAturChanIntervalCorrectedBlks, adslAturChanIntervalUncorrectBlks, adslAturChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 22 } adslAturLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThresh15MinLofs, adslAtucThresh15MinLoss, adslAtucThresh15MinESs, adslAtucThreshFastRateUp, adslAtucThreshInterleaveRateUp, adslAtucThreshFastRateDown, adslAtucThreshInterleaveRateDown, adslAtucInitFailureTrapEnable, adslAturThresh15MinLofs, adslAturThresh15MinLoss, adslAturThresh15MinLprs, adslAturThresh15MinESs, adslAturThreshFastRateUp, adslAturThreshInterleaveRateUp, adslAturThreshFastRateDown, adslAturThreshInterleaveRateDown } STATUS current DESCRIPTION "A collection of objects providing alarm provisioning information about an ADSL Line provided by the ATU-R agent." ::= { adslGroups 23 } adslAturLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslLineAlarmConfProfile, adslLineAlarmConfProfileRowStatus } STATUS current DESCRIPTION "A collection of objects providing profile control for the ADSL system by the ATU-R agent." ::= { adslGroups 24 } adslAturNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucPerfLofsThreshTrap, adslAtucPerfLossThreshTrap, adslAtucPerfESsThreshTrap, adslAtucRateChangeTrap, adslAturPerfLofsThreshTrap, adslAturPerfLossThreshTrap, adslAturPerfLprsThreshTrap, adslAturPerfESsThreshTrap, adslAturRateChangeTrap } STATUS current DESCRIPTION "The collection of ADSL notifications implemented by the ATU-R agent." ::= { adslGroups 25 } END