ARRIS-C3-MAC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TimeInterval, RowStatus, TruthValue, DisplayString FROM SNMPv2-TC ifIndex FROM IF-MIB -- RFC2233 TenthdBmV FROM DOCS-IF-MIB -- RFC2670 TenthdB FROM DOCS-IF-MIB -- RFC2670 cmtsC3 FROM ARRIS-MIB; cmtsC3MACMIB MODULE-IDENTITY LAST-UPDATED "200412030000Z" -- 3nd Dec 2004 ORGANIZATION "Arris International" CONTACT-INFO " Network Management Postal: Arris International. 4400 Cork Airport Business Park Cork Airport, Kinsale Road Cork, Ireland. Tel: +353 21 7305 800 Fax: +353 21 4321 972" DESCRIPTION "This MIB manages the MAC software on the Cadant C3 CMTS." REVISION "200411210000Z" DESCRIPTION "Changes to support fully programmable IF frequency. Added support for downstream wireless mode. Updated some mib descriptions for clarity and typos. Added mixed mode to DocsisMacType definition which defines a docsis downstream and euro-docsis upstream configuration that is used by some customers in lieu of annex C mode which the CMTS does not support in hardware. Added support for downstream wireless mode." REVISION "200411260000Z" DESCRIPTION "Added dcxMACUpChannelinitialRangingDelay." REVISION "200412030000Z" DESCRIPTION "Added dcxMACUccMaxFailedAttempts." ::= { cmtsC3 6 } DocsisMacType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the DOCSIS Channel Type." SYNTAX INTEGER { docsis (1), euroDocsis (2), mixed (3), custom(4) } dcxMACObjects OBJECT IDENTIFIER ::= { cmtsC3MACMIB 1 } dcxMACCmtsMacTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACCmtsMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for docsIfCmtsMacTable. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127)." ::= { dcxMACObjects 1 } dcxMACCmtsMacEntry OBJECT-TYPE SYNTAX DcxMACCmtsMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "dcxMACCmtsMacEntry" INDEX {ifIndex} ::= { dcxMACCmtsMacTable 1 } DcxMACCmtsMacEntry ::= SEQUENCE { dcxMACCmtsMacMode DocsisMacType, dcxMACCableAdvanceType INTEGER, dcxMACPlantLength Unsigned32, dcxMACFlapAgingTime Unsigned32, dcxMACFlapInsertTime Unsigned32, dcxMACFlapMissThresh Unsigned32, dcxMACFlapListSize Unsigned32, dcxMACCmOfflineAgingTime Unsigned32, dcxMACUccMaxFailedAttempts Unsigned32 } dcxMACCmtsMacMode OBJECT-TYPE SYNTAX DocsisMacType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the mode in which the MAC is operating. A read to this value may return any of the modes defined by DocsisMacType. Only the modes docsis, euroDocsis and mixed may be written. When set to docsis or euroDocsis, all downstream and upstream channels in this MAC domain will be configured in DOCSIS or EuroDOCSIS mode respectively. When set to mixed, the downstream channels will be configured in DOCSIS and the upstream channels will be running in EuroDOCSIS mode. The value custom will be returned in a read operation if any of the underlying channels has been reconfigured in such a way that the MAC can not be described a docsis, euroDocsis or mixed." ::= { dcxMACCmtsMacEntry 1 } dcxMACCableAdvanceType OBJECT-TYPE SYNTAX INTEGER { static(0), dynamic(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Map Advance Type - 0 for Static, 1 for Dynamic." ::= { dcxMACCmtsMacEntry 2 } dcxMACPlantLength OBJECT-TYPE SYNTAX Unsigned32 (0..161) UNITS "kilometers" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Plant Length (1-way) in kilometers." ::= { dcxMACCmtsMacEntry 3 } dcxMACFlapAgingTime OBJECT-TYPE SYNTAX Unsigned32 (0..864000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Flap List Aging Time in seconds." ::= { dcxMACCmtsMacEntry 4 } dcxMACFlapInsertTime OBJECT-TYPE SYNTAX Unsigned32 ( 0..86400 ) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Flap List Insertion Time threshold in seconds." ::= { dcxMACCmtsMacEntry 5 } dcxMACFlapMissThresh OBJECT-TYPE SYNTAX Unsigned32 (0..12) UNITS "misses" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Flap List Miss Threshold in misses." ::= { dcxMACCmtsMacEntry 6 } dcxMACFlapListSize OBJECT-TYPE SYNTAX Unsigned32 (0..6000) UNITS "entries" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable Flap List Maximum Number of Entries." ::= { dcxMACCmtsMacEntry 8 } dcxMACCmOfflineAgingTime OBJECT-TYPE SYNTAX Unsigned32 (3600..864000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Cable modem offline aging time in seconds. Minimum value is 1 hour. Maximum time before aging a modem is 10 days. Default value is 24 hours." DEFVAL { 86400 } ::= { dcxMACCmtsMacEntry 9 } dcxMACUccMaxFailedAttempts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of consecutive failed channel change attempts that a modem is allowed before the CMTS decides to no longer use the modem for load balancing purposes. If a modem successfully completes a channel change before the maximum number of attempts is reached, the number of consecutive failed attempts for the modem is reset. A value of 0 indicates no limit." DEFVAL { 2 } ::= { dcxMACCmtsMacEntry 10 } dcxMACDownstreamChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACDownstreamChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for docsIfDownstreamChannelTable. An entry in this table exists for each ifEntry with an ifType of docsCableDownstream(128)." ::= { dcxMACObjects 2 } dcxMACDownstreamChannelEntry OBJECT-TYPE SYNTAX DcxMACDownstreamChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "dcxMACDownstreamChannelEntry" INDEX {ifIndex} ::= { dcxMACDownstreamChannelTable 1 } DcxMACDownstreamChannelEntry ::= SEQUENCE { dcxMACDownChannelMacMode DocsisMacType, dcxMACDownChannelUpconverter INTEGER, dcxMACDownChannelIfFrequency Integer32, dcxMACDownChannelWirelessMode INTEGER, dcxMACDownChannelSymbolRate Integer32, dcxMACDownChannelAlpha Integer32 } dcxMACDownChannelMacMode OBJECT-TYPE SYNTAX DocsisMacType MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the downstream to DOCSIS or EuroDOCSIS. When dcxMACDownChannelWirelessMode is disabled, changes to this will impact the downstream annex type, modulation, symbol rate and interleaver. When wireless mode is enabled, only the annex type and interleaver will be changed." ::= { dcxMACDownstreamChannelEntry 1 } dcxMACDownChannelUpconverter OBJECT-TYPE SYNTAX INTEGER { internal(1), external(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Controls whether or not the internal upconverter is used. If set to internal, the downstream IF frequency will operate in read-only mode and will be configured internally by the CMTS based on the downstream channel configuration. If set to external, the IF frequency may be programmed to set the frequency supplied to an external upconverter via the IF output. In this mode, the downstream RF frequency and power will both return 0 when read." ::= { dcxMACDownstreamChannelEntry 2 } dcxMACDownChannelIfFrequency OBJECT-TYPE SYNTAX Integer32 (10000000..60000000) UNITS "hertz" MAX-ACCESS read-write STATUS current DESCRIPTION "The IF frequency output by the modulator for this channel." ::= { dcxMACDownstreamChannelEntry 3 } dcxMACDownChannelWirelessMode OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enabling this mode allows non-standard downstream modulations and symbol rates to be configured which are suitable when using the CMTS in a wireless application. Changes to dcxMACDownChannelMacMode when wireless mode is active will only impact the downstream annex type and interleaver settings. Modulation and symbol rates will only be affected when wireless mode is disabled. Disabling wireless mode will reset any non-standard modulation and symbol rates settings in order to restore a standard DOCSIS or EuroDOCSIS downstream. If a set to active fails, a license may be required to activate the feature." ::= { dcxMACDownstreamChannelEntry 4 } dcxMACDownChannelSymbolRate OBJECT-TYPE SYNTAX Integer32 (1250000..6952000) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the downstream symbol rate." ::= { dcxMACDownstreamChannelEntry 5 } dcxMACDownChannelAlpha OBJECT-TYPE SYNTAX Integer32 UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "The percentage of excess bandwidth for the channel." ::= { dcxMACDownstreamChannelEntry 6 } dcxMACUpstreamChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACUpstreamChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for docsIfUpstreamChannelTable. An entry in this table exists for each ifEntry with an ifType of docsCableUpstream(129)." ::= { dcxMACObjects 3 } dcxMACUpstreamChannelEntry OBJECT-TYPE SYNTAX DcxMACUpstreamChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "dcxMACUpstreamChannelEntry" INDEX {ifIndex} ::= { dcxMACUpstreamChannelTable 1 } DcxMACUpstreamChannelEntry ::= SEQUENCE { dcxMACUpChannelMacMode DocsisMacType, dcxMACUpChannelAmpAttenuation TenthdBmV, dcxMACUpChannelIngressCancellation INTEGER, dcxMACUpChannelGroupId Unsigned32, dcxMACUpChannelShortPollInterval TimeInterval, dcxMACUpChannelPeriodicPollInterval TimeInterval, dcxMACUpChannelInputPowerMode INTEGER, dcxMACUpChannelPower TenthdBmV, dcxMACUpChannelPlantLength Unsigned32, dcxMACUpChannelMaxCmMapProcTime Unsigned32, dcxMACUpChannelConcatenation TruthValue, dcxMACUpChannelSpMgtTriggerIndex Unsigned32, dcxMACUpChannelLowPowerOffset TenthdBmV, dcxMACUpChannelHighPowerOffset TenthdBmV, dcxMACUpChannelLogSnrAveTimeconstant Unsigned32, dcxMACUpChannelImpulseMitigation INTEGER, dcxMACUpChannelRngPreambleGuardSymbols Unsigned32, dcxMACUpChannelNrngPreambleGuardSymbols Unsigned32, dcxMACUpChannelExtendedFrequencyErrorDetect INTEGER, dcxMACUpChannelLogC3SnrTimeconstant Unsigned32, dcxMACUpChannelSignalNoise TenthdB, dcxMACUpChannelSafeConfig TruthValue, dcxMACUpChannelInitialRangingDelay Unsigned32 } dcxMACUpChannelMacMode OBJECT-TYPE SYNTAX DocsisMacType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the mode in which this upstream is operating. A read or write to this may consist only of the values docsis or euroDocsis." ::= { dcxMACUpstreamChannelEntry 1 } dcxMACUpChannelAmpAttenuation OBJECT-TYPE SYNTAX TenthdBmV MAX-ACCESS read-write STATUS current DESCRIPTION "The amplifier attenuation level for this logical channel." ::= { dcxMACUpstreamChannelEntry 2 } dcxMACUpChannelIngressCancellation OBJECT-TYPE SYNTAX INTEGER { disabled(1), tdmaOnly(2), scdmaSec(3), scdmaInc1(4), scdmaInc2(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the ingress noise cancellation mode for this logical channel. Not all modes may be valid for a given logical channel configuration or hardware." ::= { dcxMACUpstreamChannelEntry 3 } dcxMACUpChannelGroupId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The group ID for this logical channel used to associate it with other upsteams on the same physical network. The group ID is an index into the dcxMACUpstreamGroupTable which defines common parameters for grouped upsteams. Upstreams do not have to be grouped and there may be more than one group on the same physical network. Spatially diverse upstreams should not have the same group ID." ::= { dcxMACUpstreamChannelEntry 4 } dcxMACUpChannelShortPollInterval OBJECT-TYPE SYNTAX TimeInterval (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The short interval for initial unicast maintanance on this logical channel." ::= { dcxMACUpstreamChannelEntry 5 } dcxMACUpChannelPeriodicPollInterval OBJECT-TYPE SYNTAX TimeInterval (100..10000) MAX-ACCESS read-write STATUS current DESCRIPTION "The periodic station maintanance interval on this logical channel." ::= { dcxMACUpstreamChannelEntry 6 } dcxMACUpChannelInputPowerMode OBJECT-TYPE SYNTAX INTEGER { fixed(1), automatic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The receiver input power mode for this logical channel. In fixed mode the input power to the demodulator will remain fixed across symbol rate changes. In automatic mode the demodulator may vary the input power for optimal performance." ::= { dcxMACUpstreamChannelEntry 7 } dcxMACUpChannelPower OBJECT-TYPE SYNTAX TenthdBmV MAX-ACCESS read-write STATUS current DESCRIPTION "The nominal receiver input power for this logical channel." ::= { dcxMACUpstreamChannelEntry 8 } dcxMACUpChannelPlantLength OBJECT-TYPE SYNTAX Unsigned32 (1..320) MAX-ACCESS read-write STATUS current DESCRIPTION "The cable length in km to the most distant CM on this logical upstream." ::= { dcxMACUpstreamChannelEntry 9 } dcxMACUpChannelMaxCmMapProcTime OBJECT-TYPE SYNTAX Unsigned32 (0..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time in microseconds allowed for modems on this logical channel to process the Upstream Bandwidth Allocation MAP." ::= { dcxMACUpstreamChannelEntry 10 } dcxMACUpChannelConcatenation OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables the use of packet concatenation by Cable Modems on this logical channel." ::= { dcxMACUpstreamChannelEntry 11 } dcxMACUpChannelSpMgtTriggerIndex OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "An index into spectral management trigger table, identical to dcxMACSpMgtTriggerIndex in that table. All entries with the same value of dcxMACSpMgtTriggerIndex form a trigger group all assigned to the same logical upstream channel or group. Returns 0 if there are no triggers assigned to this logical channel." ::= { dcxMACUpstreamChannelEntry 12 } dcxMACUpChannelLowPowerOffset OBJECT-TYPE SYNTAX TenthdBmV (-100..-10) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum power offset of a burst below the nominal input power to the CMTS that will not cause a RNG-RSP with status continue. Valid range is from -10 dBmV to -1 dBmV in 1 dB increments." DEFVAL { -60 } ::= { dcxMACUpstreamChannelEntry 13 } dcxMACUpChannelHighPowerOffset OBJECT-TYPE SYNTAX TenthdBmV (10..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum power offset of a burst above the nominal input power to the CMTS that will not cause a RNG-RSP with status continue. Valid range is from +1 dBmV to +10 dBmV in 1 dB increments." DEFVAL { 60 } ::= { dcxMACUpstreamChannelEntry 14 } dcxMACUpChannelLogSnrAveTimeconstant OBJECT-TYPE SYNTAX Unsigned32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The averaging timeconstant used to calculate the per-logical channel MIB variable docsIfSigQSignalNoise. The averaging uses a logarithmic scale, so that the actual timeconstant used is 2^X, where X is the value configured for this object. Increasing the value of X increases the degree to which the SNR results are averaged over time, and reduces the sensitivity of the reported channel SNR to local oscillations in signal quality. Averaging can effectively be disabled by setting this object to 0" DEFVAL { 2 } ::= { dcxMACUpstreamChannelEntry 15 } dcxMACUpChannelImpulseMitigation OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables impulse noise mitigation for this logical channel." ::= { dcxMACUpstreamChannelEntry 16 } dcxMACUpChannelRngPreambleGuardSymbols OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of guard symbols before the preamble pilot pattern for ranging bursts. Guard symbols may help the receiver to mitigate the effects of ISI and\or help with the detection of bursts with an early arrival time" ::= { dcxMACUpstreamChannelEntry 17 } dcxMACUpChannelNrngPreambleGuardSymbols OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of guard symbols before the preamble pilot pattern for non-ranging bursts. Guard symbols may help the receiver to mitigate the effects of ISI and\or help with the detection of bursts with an early arrival time" ::= { dcxMACUpstreamChannelEntry 18 } dcxMACUpChannelExtendedFrequencyErrorDetect OBJECT-TYPE SYNTAX INTEGER { none(0), initialRanging(1), periodicRanging(2), allRanging(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Offsets in carrier frequency in the modem are corrected by the CMTS during ranging. Typically most if not all off the frequency error is removed in the initial ranging response with incremental changes removed during periodic ranging. If large frequency offsets are expected during initial or periodic ranging, this value may be configured to provide extended frequency offset detection and correction." DEFVAL { none } ::= { dcxMACUpstreamChannelEntry 19 } dcxMACUpChannelLogC3SnrTimeconstant OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The averaging timeconstant used to calculate the per-logical channel MIB variable dcxMACUpChannelSignalNoise. The averaging uses a logarithmic scale, so that the actual timeconstant used is 2^X, where X is the value configured for this object. Increasing the value of X increases the degree to which the SNR results are averaged over time, and reduces the sensitivity of the reported channel SNR to local oscillations in signal quality. Averaging can effectively be disabled by setting this object to 0" ::= { dcxMACUpstreamChannelEntry 20 } dcxMACUpChannelSignalNoise OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "A measurement of the average signal/noise ratio for the logical upstream. The averaging may be controlled using the dcxMACUpChannelLogC3SnrTimeconstant variable" ::= { dcxMACUpstreamChannelEntry 21 } dcxMACUpChannelSafeConfig OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If true, MIB SETs which would cause this logical channel to go offline will return a failure" ::= { dcxMACUpstreamChannelEntry 22 } dcxMACUpChannelInitialRangingDelay OBJECT-TYPE SYNTAX Unsigned32 (300..3000) UNITS "microseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of extra microseconds to allow in a broadcast IUC3 grant to compensate for modems that perform initial ranging later than expected." ::= { dcxMACUpstreamChannelEntry 23 } dcxMACUpstreamGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACUpstreamGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries containing definitions for group IDs that can be associated with an upstream channel." ::= { dcxMACObjects 4 } dcxMACUpstreamGroupEntry OBJECT-TYPE SYNTAX DcxMACUpstreamGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "dcxMACUpstreamGroupEntry" INDEX { dcxMACUpstreamGroupId } ::= { dcxMACUpstreamGroupTable 1 } DcxMACUpstreamGroupEntry ::= SEQUENCE { dcxMACUpstreamGroupId Unsigned32, dcxMACUpstreamGroupName OCTET STRING, dcxMACUpstreamGroupLoadBalancing INTEGER, dcxMACUpstreamGroupFrequencyIndex Unsigned32, dcxMACUpstreamGroupSpMgtTriggerIndex Unsigned32, dcxMACUpstreamGroupStatus RowStatus } dcxMACUpstreamGroupId OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ID for this group." ::= { dcxMACUpstreamGroupEntry 1 } dcxMACUpstreamGroupName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..63)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name associated with this group" ::= { dcxMACUpstreamGroupEntry 2 } dcxMACUpstreamGroupLoadBalancing OBJECT-TYPE SYNTAX INTEGER { none(1), initialNumeric(2), periodic(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Configures upstream load balancing for the group. Options are: none, initialNumeric, periodic. If set to none, no load balancing will be performed. If set to initialNumeric, the CMTS may redirect modems to other active upstream channels in the same group by setting the upstream channel ID override in the RNG-RSP at any time up to the point where the modem successfully completes periodic ranging. Once a modem has completed ranging it must be reset before it may be moved to another upstream. The modems in a group will be distributed evenly and numerically across the active channels in the group. When a modems performs initial ranging, it will be sent to the upsteam with the least number of active modems if the number of active modems on the current upsteam is greater than the average number of modems per upsteam in the group. All channels are treated equally when calculating loads. If a modem fails to range on the desired channel following a ranging overide, it will be allowed to remain on the channel on which it next performs initial ranging. If set to periodic, modems will be numerically distributed during initial ranging and then selectively moved after registration using UCC. Periodic load balancing will attempt to distribute the modems to maintain even bandwidth utilization across the channels in a group." DEFVAL { none } ::= { dcxMACUpstreamGroupEntry 3 } dcxMACUpstreamGroupFrequencyIndex OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "An index into upstream frequency table, identical to dcxMACUpstreamFrequencyIndex in that table. All entries with the same value of dcxMACUpstreamFrequencyIndex form a spectral frequency group all assigned to the same upstream group. Returns 0 if there are no triggers assigned to this group." ::= { dcxMACUpstreamGroupEntry 4 } dcxMACUpstreamGroupSpMgtTriggerIndex OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "An index into spectral management trigger table, identical to dcxMACSpMgtTriggerIndex in that table. All entries with the same value of dcxMACSpMgtTriggerIndex form a trigger group all assigned to the same upstream group or channel. Returns 0 if there are no triggers assigned to this group." ::= { dcxMACUpstreamGroupEntry 5 } dcxMACUpstreamGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create rows in this table" ::= { dcxMACUpstreamGroupEntry 6 } dcxMACUpstreamFrequencyTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACUpstreamFrequencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the upstream spectrum available for use by one or more upstream groups. Entries are grouped by dcxMACUpstreamFrequencyIndex, with each group assigned to one or more upstream groups." ::= { dcxMACObjects 5 } dcxMACUpstreamFrequencyEntry OBJECT-TYPE SYNTAX DcxMACUpstreamFrequencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a single contiguous region of upstream spectrum, available for use by one or more upstream spectral groups." INDEX { dcxMACUpstreamFrequencyIndex, dcxMACUpstreamFrequencyRegion } ::= { dcxMACUpstreamFrequencyTable 1 } DcxMACUpstreamFrequencyEntry ::= SEQUENCE { dcxMACUpstreamFrequencyIndex Unsigned32, dcxMACUpstreamFrequencyRegion Unsigned32, dcxMACUpstreamFrequencyStart Integer32, dcxMACUpstreamFrequencyStop Integer32, dcxMACUpstreamFrequencyStatus RowStatus } dcxMACUpstreamFrequencyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the upstream frequency table representing a group of spectral regions, all associated with the same upstream spectral group." ::= { dcxMACUpstreamFrequencyEntry 1 } dcxMACUpstreamFrequencyRegion OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the upstream frequency table which, when grouped with other frequency regions with the same frequency index fully describe the upstream frequency spectrum available for use by a given spectral group." ::= { dcxMACUpstreamFrequencyEntry 2 } dcxMACUpstreamFrequencyStart OBJECT-TYPE SYNTAX Integer32 UNITS "hertz" MAX-ACCESS read-create STATUS current DESCRIPTION "The start frequency for this upstream spectral region." ::= { dcxMACUpstreamFrequencyEntry 3 } dcxMACUpstreamFrequencyStop OBJECT-TYPE SYNTAX Integer32 UNITS "hertz" MAX-ACCESS read-create STATUS current DESCRIPTION "The stop frequency for this upstream spectral region." ::= { dcxMACUpstreamFrequencyEntry 4 } dcxMACUpstreamFrequencyStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create entries in this table." ::= { dcxMACUpstreamFrequencyEntry 5 } dcxMACSpectralMgtObjects OBJECT IDENTIFIER ::= { dcxMACObjects 6 } dcxMACSpectralMgtTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACSpectralMgtTriggerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the spectral management triggers assigned to one or more upstream groups or channels. Entries are grouped by dcxMACSpMgtTriggerIndex, with each group assigned to one or more upstream channels or groups." ::= { dcxMACSpectralMgtObjects 1 } dcxMACSpectralMgtTriggerEntry OBJECT-TYPE SYNTAX DcxMACSpectralMgtTriggerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a single spectral management trigger, available for use by one or more upstream channels or spectral groups." INDEX { dcxMACSpMgtTriggerIndex, dcxMACSpMgtTriggerNumber } ::= { dcxMACSpectralMgtTriggerTable 1 } DcxMACSpectralMgtTriggerEntry::= SEQUENCE { dcxMACSpMgtTriggerIndex Unsigned32, dcxMACSpMgtTriggerNumber Unsigned32, dcxMACSpMgtTriggerType Integer32, dcxMACSpMgtTriggerAction Unsigned32, dcxMACSpMgtTriggerParam1 Integer32, dcxMACSpMgtTriggerParam2 Integer32, dcxMACSpMgtTriggerParam3 Integer32, dcxMACSpMgtTriggerParam4 Integer32, dcxMACSpMgtTriggerParam5 Integer32, dcxMACSpMgtTriggerParam6 Integer32, dcxMACSpMgtTriggerParam7 Integer32, dcxMACSpMgtTriggerParam8 Integer32, dcxMACSpMgtTriggerStatus RowStatus } dcxMACSpMgtTriggerIndex OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the spectral managment trigger table representing a group of triggers, all assigned to the same upstream channel or spectral group." ::= { dcxMACSpectralMgtTriggerEntry 1 } dcxMACSpMgtTriggerNumber OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the spectral managment trigger table which, when grouped with other triggers with the same trigger index fully describe the spectral mangement triggers assigned to the same upstream channel or spectral group." ::= { dcxMACSpectralMgtTriggerEntry 2 } dcxMACSpMgtTriggerType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the trigger type represented by this entry." ::= { dcxMACSpectralMgtTriggerEntry 3 } dcxMACSpMgtTriggerAction OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "An index into the spectral management action table, identical to dcxMACSpMgtActionIndex in that table, identifying the action to take if this trigger is invoked. Returns 0 if there is no action associated with this trigger." ::= { dcxMACSpectralMgtTriggerEntry 4 } dcxMACSpMgtTriggerParam1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 5 } dcxMACSpMgtTriggerParam2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 6 } dcxMACSpMgtTriggerParam3 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 7 } dcxMACSpMgtTriggerParam4 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 8 } dcxMACSpMgtTriggerParam5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 9 } dcxMACSpMgtTriggerParam6 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 10 } dcxMACSpMgtTriggerParam7 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 11 } dcxMACSpMgtTriggerParam8 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on trigger type." ::= { dcxMACSpectralMgtTriggerEntry 12 } dcxMACSpMgtTriggerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and control the status of entries in this table." ::= { dcxMACSpectralMgtTriggerEntry 13 } dcxMACSpectralMgtActionTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACSpectralMgtActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the spectral management actions assigned to one or more spectral managment triggers." ::= { dcxMACSpectralMgtObjects 2 } dcxMACSpectralMgtActionEntry OBJECT-TYPE SYNTAX DcxMACSpectralMgtActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a single spectral management action, assigned to one or more spectral management triggers." INDEX { dcxMACSpMgtActionIndex } ::= { dcxMACSpectralMgtActionTable 1 } DcxMACSpectralMgtActionEntry::= SEQUENCE { dcxMACSpMgtActionIndex Unsigned32, dcxMACSpMgtActionType Integer32, dcxMACSpMgtActionParam1 Integer32, dcxMACSpMgtActionParam2 Integer32, dcxMACSpMgtActionParam3 Integer32, dcxMACSpMgtActionParam4 Integer32, dcxMACSpMgtActionParam5 Integer32, dcxMACSpMgtActionParam6 Integer32, dcxMACSpMgtActionParam7 Integer32, dcxMACSpMgtActionParam8 Integer32, dcxMACSpMgtActionStatus RowStatus } dcxMACSpMgtActionIndex OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the spectral managment actions table used to assign actions to spectral management triggers." ::= { dcxMACSpectralMgtActionEntry 1 } dcxMACSpMgtActionType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the action type represented by this entry." ::= { dcxMACSpectralMgtActionEntry 2 } dcxMACSpMgtActionParam1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 3 } dcxMACSpMgtActionParam2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 4 } dcxMACSpMgtActionParam3 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 5 } dcxMACSpMgtActionParam4 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 6 } dcxMACSpMgtActionParam5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 7 } dcxMACSpMgtActionParam6 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 8 } dcxMACSpMgtActionParam7 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 9 } dcxMACSpMgtActionParam8 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter dependent on action type." ::= { dcxMACSpectralMgtActionEntry 10 } dcxMACSpMgtActionStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and control the status of entries in this table." ::= { dcxMACSpectralMgtActionEntry 11 } -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Shared Secret configuration -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- dcxMACSharedSecretTable OBJECT-TYPE SYNTAX SEQUENCE OF DcxMACSharedSecretEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Set up shared secrets for this DOCSIS MAC Interface" ::= { dcxMACObjects 7 } dcxMACSharedSecretEntry OBJECT-TYPE SYNTAX DcxMACSharedSecretEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "dcxMACSharedSecretEntry" INDEX {ifIndex, dcxMACSharedSecretId} ::= { dcxMACSharedSecretTable 1 } DcxMACSharedSecretEntry ::= SEQUENCE { dcxMACSharedSecretId Integer32, dcxMACSharedSecretStr DisplayString, dcxMACSharedSecretStatus RowStatus } dcxMACSharedSecretId OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "ID for the associated shared secret." ::= { dcxMACSharedSecretEntry 1 } dcxMACSharedSecretStr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "This is the shared secret itself, which is considered write-only. It can be SET but when a GET operation is performed the value is not returned." ::= { dcxMACSharedSecretEntry 2 } dcxMACSharedSecretStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status." ::= { dcxMACSharedSecretEntry 3 } END