-- -- whisp-box-mib.mib -- GENERATED FROM ui_db.xml -- -- **************************************************************************************************** -- Copyright 2005 - 2015 (c), Cambium Networks -- Cambium Networks Confidential Proprietary -- **************************************************************************************************** -- -- Canopy Box Level(AP,SM and Backhaul) MIB definitions. -- -- *************************************************************************************************** WHISP-BOX-MIBV2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64, Gauge32, IpAddress, NOTIFICATION-TYPE, Unsigned32 FROM SNMPv2-SMI DisplayString, MacAddress FROM SNMPv2-TC OBJECT-GROUP FROM SNMPv2-CONF WhispLUID, WhispMACAddress, EventString FROM WHISP-TCV2-MIB whispModules, whispBox FROM WHISP-GLOBAL-REG-MIB ; whispBoxLevelMibModule MODULE-IDENTITY LAST-UPDATED "200304150000Z" ORGANIZATION "Cambium Networks" CONTACT-INFO "Cambium Networks Support email: support@cambiumnetworks.com" DESCRIPTION "This module contains generic Box-Level MIB definitions for Canopy Radios." ::= {whispModules 8} -- ------------------------------------------------------------------------- -- Top Level Registrations whispBoxStatus OBJECT IDENTIFIER ::= {whispBox 1} whispBoxConfig OBJECT IDENTIFIER ::= {whispBox 2} whispBoxControls OBJECT IDENTIFIER ::= {whispBox 3} whispBoxEventLog OBJECT IDENTIFIER ::= {whispBox 5} whispBoxConf OBJECT IDENTIFIER ::= {whispBox 6} whispBoxGroups OBJECT IDENTIFIER ::= {whispBoxConf 1} whispBoxBridgeVar OBJECT IDENTIFIER ::= {whispBox 7} whispBoxCPVar OBJECT IDENTIFIER ::= {whispBox 9} whispBoxEvent OBJECT IDENTIFIER ::= {whispBox 12} whispBoxDHCPClientEvent OBJECT IDENTIFIER ::= {whispBoxEvent 1} whispBoxPoEEvent OBJECT IDENTIFIER ::= {whispBoxEvent 2} whispBoxRadioAlarmEvent OBJECT IDENTIFIER ::= {whispBoxEvent 3} whispBoxDNS OBJECT IDENTIFIER ::= {whispBox 13} whispBoxSNMPv3 OBJECT IDENTIFIER ::= {whispBox 14} whispBoxLink OBJECT IDENTIFIER ::= {whispBox 18} whispBoxLinkTestConfig OBJECT IDENTIFIER ::= {whispBoxLink 1} whispBoxLinkTestResult OBJECT IDENTIFIER ::= {whispBoxLink 2} whispBoxLinkTestMVCResult OBJECT IDENTIFIER ::= {whispBoxLink 5} whispUserAuthSecurity OBJECT IDENTIFIER ::= {whispBox 19} whispBoxRFPhysical OBJECT IDENTIFIER ::= {whispBox 15} whispBoxRFConfig OBJECT IDENTIFIER ::= {whispBox 16} -- ------------------------------------------------------------------------- -- Canopy radio status page whispBoxSoftwareVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Version of software. Should be noted in the event customer has technical difficulties and need to contact technical support." ::={whispBoxStatus 1} whispBoxFPGAVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Version of FPGA." ::={whispBoxStatus 2} whispBoxEsn OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Electronic serial number(MAC address) assigned to Radio." ::={whispBoxStatus 3} whispBoxBoot OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Software boot version." ::={whispBoxStatus 4} boxTemperature OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Radio temperature." ::={whispBoxStatus 5} boxDeviceType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the device." ::={whispBoxStatus 6} boxDeviceTypeID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device type ID." ::={whispBoxStatus 7} boxEncryption OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device encryption type. Note: Returns DES also when encryption is set to None on AP." ::={whispBoxStatus 8} etherLinkStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet link status." ::={whispBoxStatus 9} boxFrequency OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Frequency band of the device." ::={whispBoxStatus 10} platformVer OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Hardware platform version. For internal use." ::={whispBoxStatus 11} platformType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Platform type: Canopy, Canopy Lite, Canopy Lite - Advantage, Advantage, Russian, Russian - Advantage." ::={whispBoxStatus 12} dhcpLanIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "LAN interface IP obtained through DHCP." ::={whispBoxStatus 13} dhcpLanSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "LAN interface Subnet Mask obtained through DHCP." ::={whispBoxStatus 14} dhcpLanGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "LAN interface Gateway obtained through DHCP." ::={whispBoxStatus 15} dhcpRfPublicIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "RF Public interface IP obtained through DHCP." ::={whispBoxStatus 16} dhcpRfPublicSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "RF Public interface Subnet Mask obtained through DHCP." ::={whispBoxStatus 17} dhcpRfPublicGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "RF Public interface Gateway obtained through DHCP." ::={whispBoxStatus 18} lanDhcpStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display LAN interface current DHPC status." ::={whispBoxStatus 19} rfPublicDhcpStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display RF Public interface current DHPC status." ::={whispBoxStatus 20} inSyncCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of In Synchronization." ::={whispBoxStatus 21} outSyncCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of Out of Synchronization." ::={whispBoxStatus 22} pllOutLockCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of PLL out of Lock." ::={whispBoxStatus 23} txCalFailure OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of TX Calibration failure." ::={whispBoxStatus 24} swVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Software version information." ::={whispBoxStatus 25} pldVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "PLD version information." ::={whispBoxStatus 26} platformInfo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Platform information." ::={whispBoxStatus 27} antPolarization OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Antenna polarization for FSK radios." ::={whispBoxStatus 28} packetOverloadCounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total packet overload count." ::={whispBoxStatus 29} whispBoxP11Personality OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Board Personality Configuration" ::={whispBoxStatus 30} whispBoxP11FPGAType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "FPGA Type" ::={whispBoxStatus 31} whispBoxP11BstrapFPGAVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "P11 Bootstrap FPGA Version." ::={whispBoxStatus 32} numDFSDetections OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DFS Detections since last boot." ::={whispBoxStatus 33} rxOverrunPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of received overrun packets error." ::={whispBoxStatus 34} boxTemperatureC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Radio temperature in Celsius." ::={whispBoxStatus 35} boxTemperatureF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Radio temperature in Fahrenheit." ::={whispBoxStatus 36} bridgeCbFecStatbin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats bin" ::={whispBoxStatus 37} bridgeCbFecStatbout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats bout" ::={whispBoxStatus 38} bridgeCbFecStatbtoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats btoss" ::={whispBoxStatus 39} bridgeCbFecStatbtosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats btosscap" ::={whispBoxStatus 40} bridgeCbFecStatuin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats uin" ::={whispBoxStatus 41} bridgeCbFecStatuout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats uout" ::={whispBoxStatus 42} bridgeCbFecStatutoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats utoss" ::={whispBoxStatus 43} bridgeCbFecStatutosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats utosscap" ::={whispBoxStatus 44} bridgeCbRFStatbin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats bin" ::={whispBoxStatus 45} bridgeCbRFStatbout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats bout" ::={whispBoxStatus 46} bridgeCbRFStatbtoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats btoss" ::={whispBoxStatus 47} bridgeCbRFStatbtosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats btosscap" ::={whispBoxStatus 48} bridgeCbRFStatuin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats uin" ::={whispBoxStatus 49} bridgeCbRFStatuout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats uout" ::={whispBoxStatus 50} bridgeCbRFStatutoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats utoss" ::={whispBoxStatus 51} bridgeCbRFStatutosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats utosscap" ::={whispBoxStatus 52} bridgeCbErrStatNI1QSend OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats ErrNI1QSend" ::={whispBoxStatus 53} bridgeCbErrStatNI2QSend OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats ErrNI2QSend" ::={whispBoxStatus 54} bridgeCbErrStatBridgeFull OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats BridgeFull" ::={whispBoxStatus 55} bridgeCbErrStatSendMsg OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats SendMsg" ::={whispBoxStatus 56} bridgeCbErrStatAPFecQSend OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats APFecQSend" ::={whispBoxStatus 57} bridgeCbErrStatApRfQSend OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Error Stats ApRfQSend" ::={whispBoxStatus 58} rfStatXmtUDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Transmit Unicast Data Count" ::={whispBoxStatus 59} rfStatXmtBDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Transmit Broadcast Data Count" ::={whispBoxStatus 60} rfStatRcvUDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Unicast Data Count" ::={whispBoxStatus 61} rfStatRcvBDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Broadcast Data Count" ::={whispBoxStatus 62} rfStatXmtCntlCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Transmit Control Count" ::={whispBoxStatus 63} rfStatRcvCntlCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Control Count" ::={whispBoxStatus 64} rfStatInSyncCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats In Sync Count" ::={whispBoxStatus 65} rfStatOutSyncCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Out Sync Count" ::={whispBoxStatus 66} rfStatOverrunCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Overrun Count" ::={whispBoxStatus 67} rfStatUnderrunCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Underrun Count" ::={whispBoxStatus 68} rfStatRcvCorruptDataCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Corrupt Data Count" ::={whispBoxStatus 69} rfStatBadBcastCtlCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Bad Broadcast Control Count" ::={whispBoxStatus 70} rfStatPLLOutOfLockCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats PLL Out of Lock Count" ::={whispBoxStatus 71} rfStatBeaconVerMismatchCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Beacon version Mismatch Count" ::={whispBoxStatus 72} rfStatBadFreqBcnRcvCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Wrong Frequency Beacon Received Count" ::={whispBoxStatus 73} rfStatnonLiteBcnRcvCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Non Lite Beacon Received Count" ::={whispBoxStatus 74} rfStatUnsupFeatBcnRcvCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Unsupported Feature Beacon Received Count" ::={whispBoxStatus 75} rfStatUnkwnFeatBcnRcvCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Unknown Feature Beacon Received Count" ::={whispBoxStatus 76} rfStatTxCalFailCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats TX Calibration Failures Count" ::={whispBoxStatus 77} rfStatBadInSyncIDRcv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Bad In Sync ID Received Count" ::={whispBoxStatus 78} rfStatTempOutOfRange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Temperature Out of Range Count" ::={whispBoxStatus 79} rfStatRSSIOutOfRange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats RSSI Out of Range Count" ::={whispBoxStatus 80} rfStatRangeCapEnf OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Range Cap Enforced Count" ::={whispBoxStatus 81} rfStatRcvLTStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Rcv LT Start Count" ::={whispBoxStatus 82} rfStatRcvLTStartHS OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Rcv LT Start HS Count" ::={whispBoxStatus 83} rfStatRcvLTResult OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Rcv LT Result Count" ::={whispBoxStatus 84} rfStatXmtLTResult OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Xmt LT Result Count" ::={whispBoxStatus 85} whispFeatureKeyOrigin OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Origin of Feature Key which includes GMT time and location of the Key programming (if time is 0 the key was converted locally)" ::={whispBoxStatus 86} radioMSN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "MSN of the radio." ::={whispBoxStatus 87} updateStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Status of Device Update" ::={whispBoxStatus 88} syslogStatTxSuccesses OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The count of Syslog messages sent to UDP layer." ::={whispBoxStatus 89} syslogStatDropped OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped syslog messages due to device overload and/or resource limitations." ::={whispBoxStatus 90} fecStatLinkLost OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet link lost count" ::={whispBoxStatus 91} fecStatLinkDetected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet link detected count" ::={whispBoxStatus 92} natDhcpStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display NAT Public interface current DHPC status." ::={whispBoxStatus 93} fecInDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet in discards count." ::={whispBoxStatus 94} fecInErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet in errors count." ::={whispBoxStatus 95} fecOutDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet out discards count." ::={whispBoxStatus 96} fecOutErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet out errors count." ::={whispBoxStatus 97} rfInDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "RF in discards count. This attribute is deprecated. Use rfInDiscardsCountExt instead." ::={whispBoxStatus 98} rfInErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "RF in errors count. This attribute is deprecated. Use rfInErrorsCountExt instead." ::={whispBoxStatus 99} rfOutDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "RF out discards count. This attribute is deprecated. Use rfOutDiscardsCountExt instead." ::={whispBoxStatus 100} rfOutErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "RF out errors count. This attribute is deprecated. Use rfOutErrorsCountExt instead." ::={whispBoxStatus 101} fecInDiscardsOverloadCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet in discards overload." ::={whispBoxStatus 102} fecOutDiscardsOverloadCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet out discards overload." ::={whispBoxStatus 103} rfInDiscardsOverloadCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Rf in discards overload." ::={whispBoxStatus 104} rfOutDiscardsOverloadCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Rf out discards overload." ::={whispBoxStatus 105} fpgaCompileInfo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display the fpga compiled attributes. (Engineering Only)" ::={whispBoxStatus 106} fpgaBuildDate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display the entire fpga build date string. (Engineering Only)" ::={whispBoxStatus 107} aggregateBandwidthCap OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum aggregate (uplink + downlink) the radio is capable of." ::={whispBoxStatus 108} calibrationStatusBool OBJECT-TYPE SYNTAX INTEGER { notCalibrated(0), calibrated(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "Boolean OID to show if device is calibrated. Applicable to FSK and MIMO radios only." ::={whispBoxStatus 109} calibrationStatusBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "String to show if radio is calibrated. Applicable to FSK and MIMO radios only." ::={whispBoxStatus 110} radioEngKeyed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This will be set either as 0 if the engineering key patch is not applied to the radio or 1 if it is applied." ::={whispBoxStatus 111} bridgeCbFecStatfloods OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB FEC Stats Floods (Multipoint AP only)" ::={whispBoxStatus 112} bridgeCbRFStatfloods OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB RF Stats Floods (Multipoint AP only)" ::={whispBoxStatus 113} catalinaGainRxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Rcv Gain on Catalina Rx CH1. Engineering use only." ::={whispBoxStatus 114} catalinaGainRxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Rcv Gain on Catalina Rx CH2. Engineering use only." ::={whispBoxStatus 115} antType OBJECT-TYPE SYNTAX INTEGER { integrated(0), external(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the antenna is integrated or external (connectorized)." ::={whispBoxStatus 116} rfStatRcvCorruptControlCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Corrupt Control Data Count" ::={whispBoxStatus 117} numLBTDetections OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of LBT Detections since last boot." ::={whispBoxStatus 118} bridgeCbEthAuxStatbin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats bin" ::={whispBoxStatus 119} bridgeCbEthAuxStatbout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats bout" ::={whispBoxStatus 120} catalinaAttenTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Attenuation on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 121} catalinaAttenTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Attenuation on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 122} catalinaCurrDetSetpointTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector Setpoint on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 123} catalinaCurrDetSetpointTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector Setpoint on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 124} catalinaCurrDetReadRefTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector Reference on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 125} catalinaCurrDetReadRefTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector Reference on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 126} catalinaCurrDetReadPowerOnTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector PowerOn on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 127} catalinaCurrDetReadPowerOnTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Detector PowerOn on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 128} catalinaOpenLoopAttenTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Open Loop Attenuation on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 129} catalinaOpenLoopAttenTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Open Loop Attenuation on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 130} catalinaTargetDetSetpointTxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Target Detector Setpoint on Catalina Tx CH1. Engineering Use Only." ::={whispBoxStatus 131} catalinaTargetDetSetpointTxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Target Detector Setpoint on Catalina Tx CH2. Engineering use only." ::={whispBoxStatus 132} catalinaGainReductionRxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gain Reduction on Catalina Rx CH1. Engineering Use Only." ::={whispBoxStatus 133} catalinaGainReductionRxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gain Reduction on Catalina Rx CH2. Engineering use only." ::={whispBoxStatus 134} catalinaLoAttenRxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Lo Attenuation on Catalina Rx CH1. Engineering Use Only." ::={whispBoxStatus 135} catalinaLoAttenRxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Lo Attenuation on Catalina Rx CH2. Engineering use only." ::={whispBoxStatus 136} catalinaTargetGainRxCH1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Target Gain on Catalina Rx CH1. Engineering Use Only." ::={whispBoxStatus 137} catalinaTargetGainRxCH2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Target Gain on Catalina Rx CH2. Engineering use only." ::={whispBoxStatus 138} bridgeCbEthAuxStatfloods OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats Floods (Multipoint AP only)" ::={whispBoxStatus 139} bridgeCbEthAuxStatbtoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats btoss" ::={whispBoxStatus 141} bridgeCbEthAuxStatbtosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats btosscap" ::={whispBoxStatus 142} bridgeCbEthAuxStatuin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats uin" ::={whispBoxStatus 143} bridgeCbEthAuxStatuout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats uout" ::={whispBoxStatus 144} bridgeCbEthAuxStatutoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats utoss" ::={whispBoxStatus 145} bridgeCbEthAuxStatutosscap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge CB Eth Aux Stats utosscap" ::={whispBoxStatus 146} radioWatchDogLogged OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This will be set either as 0 if there is no watchdog event logged or 1 if there is." ::={whispBoxStatus 147} radioFatalErrorLogged OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This will be set either as 0 if there is no fatalerror event logged or 1 if there is." ::={whispBoxStatus 148} fecStatLinkUptime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Uptime of main ethernet link in seconds" ::={whispBoxStatus 149} fecAuxStatLinkUptime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Uptime of main ethernet link in seconds" ::={whispBoxStatus 150} rfStatXmtMDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Transmit Multicast Data Count" ::={whispBoxStatus 217} rfStatRcvMDataCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "RF Scheduler Stats Receive Multicast Data Count" ::={whispBoxStatus 218} fecStatUnderSizedToss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Undersized Toss Count" ::={whispBoxStatus 219} fecRxBabErr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Error count in Babble Receiver." ::={whispBoxStatus 220} fecTxHbErr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets having Transmit heartbeat error." ::={whispBoxStatus 221} fecEthBusErr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ethernet Busy Error Count" ::={whispBoxStatus 222} fecCRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets having CRC Error." ::={whispBoxStatus 223} fecRxFifoNoBuf OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times could not get a buffer from Rx Fifo." ::={whispBoxStatus 224} fecRxOverrun OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times Rx Fifo Overrun." ::={whispBoxStatus 225} fecLateCollision OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets having late collision." ::={whispBoxStatus 226} fecRetransLimitExp OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets whose retransmision limit expired." ::={whispBoxStatus 227} fecTxUnderrun OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times Tx queue underrun." ::={whispBoxStatus 228} fecCarSenseLost OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Carrier Sense Lost count." ::={whispBoxStatus 229} fecNoCarrier OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "No carrier asserted by external transceiver during transmission." ::={whispBoxStatus 230} framePeriodCurrent OBJECT-TYPE SYNTAX INTEGER { twoPointFiveMs(0), fiveMs(1), scanning(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Current frame period of the radio." ::={whispBoxStatus 231} activeTxPowerStr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Current transmit power level, including potential power backoff information. Not applicable to PMP 450m." ::={whispBoxStatus 232} activeTxPowerHdths OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current transmit power level, in hundredths of dBm. Not appliable on PMP 450m." ::={whispBoxStatus 233} poeT2Status OBJECT-TYPE SYNTAX INTEGER { error(0), notPresent(1), notPresentAndIgnored(2), present(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the 802.3at Type 2 Classification status. This is only available on the 450i." ::={whispBoxStatus 234} fecAuxStatLinkDetected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet link detected count" ::={whispBoxStatus 235} fecAuxStatLinkLost OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet ink lost count" ::={whispBoxStatus 236} fecAuxInDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet in discards count." ::={whispBoxStatus 237} fecAuxInErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet in errors count." ::={whispBoxStatus 238} fecAuxOutDiscardsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet out discards count." ::={whispBoxStatus 239} fecAuxOutErrorsCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet out errors count." ::={whispBoxStatus 240} fecAuxCRCError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Number of packets having CRC Error." ::={whispBoxStatus 241} fecAuxRxOverrun OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Number of times Rx Fifo Overrun." ::={whispBoxStatus 242} fecAuxLateCollision OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Number of packets having late collision." ::={whispBoxStatus 243} fecAuxRetransLimitExp OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Number of packets whose retransmision limit expired." ::={whispBoxStatus 244} fecAuxTxUnderrun OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Number of times Tx queue underrun." ::={whispBoxStatus 245} fecAuxCarSenseLost OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Carrier Sense Lost count." ::={whispBoxStatus 246} fecAuxNoCarrier OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet No carrier asserted by external transceiver during transmission." ::={whispBoxStatus 247} fecAuxLargeFrame OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Large Frame Error." ::={whispBoxStatus 248} fecAuxRuntFrame OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "450i Aux Ethernet Runt Frame Error." ::={whispBoxStatus 249} fecLargeFrame OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Large Frame Error." ::={whispBoxStatus 250} fecRuntFrame OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Runt Frame Error." ::={whispBoxStatus 251} soundingStatClear OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Sounding Stat Clear Set to any value to clear all Sounding Stats" ::={whispBoxStatus 252} soundingStatRequestCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Request Count" ::={whispBoxStatus 253} soundingStatResponseCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Response Count" ::={whispBoxStatus 254} soundingStatRequestsIgnored OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Requests Ignored" ::={whispBoxStatus 255} soundingStatAvgRequestInterval OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Avg Request Interval (ms)" ::={whispBoxStatus 256} soundingStatMaxRequestInterval OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Max Request Interval (ms)" ::={whispBoxStatus 257} soundingStatErrorCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Error Count" ::={whispBoxStatus 258} camAccID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "CnMaestro Account to which Radio is onboarded." ::={whispBoxStatus 259} cnMaestroStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "CnMaestro connection status." ::={whispBoxStatus 260} daVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device Agent Version number." ::={whispBoxStatus 261} soundingStatRequestsDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Requests Dropped" ::={whispBoxStatus 262} soundingStatResponsesSuppressed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Responses Suppressed" ::={whispBoxStatus 263} soundingStatVersionMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sounding Stats Version Mismatch" ::={whispBoxStatus 264} hardwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Read directly from the resistors on the board is the form Major.Minor (cnMedusa-specific, Engineering Only)" ::={whispBoxStatus 265} productTypeName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Basic product type, based on board type and factory programming." ::={whispBoxStatus 266} radioStatusTransmitControlOverridden OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit mode control is overridden in config PMP 450m only." ::={whispBoxStatus 267} radioStatusTrackingFailure OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Feedback tracking loop is out of tolerance - Transmit disabled PMP 450m only." ::={whispBoxStatus 268} radioStatusSectorWeightsOff OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Sector mode weights disabled PMP 450m only." ::={whispBoxStatus 269} radioStatusRxBeamFormingOff OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Rx beamforming disabled PMP 450m only." ::={whispBoxStatus 270} radioStatusPowerDetectorInactive OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Power detector control not active PMP 450m only." ::={whispBoxStatus 271} radioStatusCatQuadCalFail OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Catalina Tx quadrature calibration failure 450 platform only. Engineering use only." ::={whispBoxStatus 272} nearFieldOperationActive OBJECT-TYPE SYNTAX INTEGER { true(1), false(0)} MAX-ACCESS read-only STATUS current DESCRIPTION "When true(1) near field operation is enabled and near field range correction is being applied. PMP 450m only." ::={whispBoxStatus 273} radioStatusAlarmReason OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Reason code associated with the cause of a Radio Status Alarm being triggered. Provide this code to Cambium Networks Support. PMP 450m only." ::={whispBoxStatus 274} radioStatusAlarm OBJECT-TYPE SYNTAX INTEGER { true(1), false(0)} MAX-ACCESS read-only STATUS current DESCRIPTION "Radio Status Alarm. PMP 450m only." ::={whispBoxStatus 275} forceReassessmentActive OBJECT-TYPE SYNTAX INTEGER { true(1), false(0)} MAX-ACCESS read-only STATUS current DESCRIPTION "When true(1) forced channel assessment is enabled. MU-MIMO only." ::={whispBoxStatus 276} fecExcessiveDeferrals OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Excessive Deferrals." ::={whispBoxStatus 277} rfInDiscardsCountExt OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Extended RF in discards count with 64 bit counters." ::={whispBoxStatus 278} rfInErrorsCountExt OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Extended RF in errors count with 64 bit counters." ::={whispBoxStatus 279} rfOutDiscardsCountExt OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Extended RF out discards count with 64 bit counters." ::={whispBoxStatus 280} rfOutErrorsCountExt OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Extended RF out errors count with 64 bit counters." ::={whispBoxStatus 281} boardModel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Returns Board model of the device." ::={whispBoxStatus 284} -- The following definitions deal with Canopy Box Level configuration variables. linkNegoSpeed OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Link negotiation speeds. H10BT -- 10 Base T Half Duplex, F10BT -- 10 Base T Full Duplex, H100BT -- 100 Base T Half Duplex, F100BT -- 100 Base T Full Duplex. Separate the values with comma when doing a set. e.g. H10BT,F10BT,H100BT,F100BT" ::={whispBoxConfig 1} colorCode OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-write STATUS current DESCRIPTION "Color code." ::={whispBoxConfig 2} displayOnlyAccess OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This variable is deprecated." ::={whispBoxConfig 3} fullAccess OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Full access password." ::={whispBoxConfig 4} webAutoUpdate OBJECT-TYPE SYNTAX INTEGER UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Web page auto update in seconds. 0 means disabled." ::={whispBoxConfig 5} pass1Status OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Password 1(display only) status." ::={whispBoxConfig 6} pass2Status OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Password 2(full access) status." ::={whispBoxConfig 7} bridgeEntryTimeout OBJECT-TYPE SYNTAX INTEGER (25..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "Bridge table time out Range : 25 -- 1440 Minutes." ::={whispBoxConfig 8} snmpMibPerm OBJECT-TYPE SYNTAX INTEGER { readWrite(0), readOnly(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Read/Write permission for MIB groups." ::={whispBoxConfig 9} bhTimingMode OBJECT-TYPE SYNTAX INTEGER { timingMaster(1), timeingSlave(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Variable to switch between Timing Master and Timing Slave. For Backhaul units only." ::={whispBoxConfig 10} bhModulation OBJECT-TYPE SYNTAX INTEGER { tenMbitsPerSecond(0), twentyMbitsPerSecond(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Modulation scheme. For Backhaul units only. Only level 4 backhaul can be changed to 20Mbits/Second." ::={whispBoxConfig 11} powerControl OBJECT-TYPE SYNTAX INTEGER { low(0), normal(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Power control. FSK Only." ::={whispBoxConfig 12} extFilterDelay OBJECT-TYPE SYNTAX INTEGER UNITS "nanoseconds" MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. External Filters Delay. For 900MHz FSK radios only." ::={whispBoxConfig 13} antennaGain OBJECT-TYPE SYNTAX INTEGER UNITS "dBi" MAX-ACCESS read-write STATUS current DESCRIPTION "External Antenna Gain. For radios that uses an external antenna or the DFS feature. Not applicable to PMP 450m." ::={whispBoxConfig 14} eirp OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Transmit EIRP of radio. PMP 450m only." ::={whispBoxConfig 15} dynamicLearning OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To enable VLAN dynamic learning." ::={whispBoxConfig 16} managementVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Management VLAN VID." ::={whispBoxConfig 17} agingTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Aging timeout." ::={whispBoxConfig 18} frameType OBJECT-TYPE SYNTAX INTEGER { allframes(0), taggedonly(1), untaggedonly(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Allow only tagged frame." ::={whispBoxConfig 19} addVlanMember OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Write-Only OID,Add VLAN number which needs to be added." ::={whispBoxConfig 20} removeVlanMember OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Write-only OID,Enter VLAN ID which needs to deleted. If Vlan doesnot exist an error will be returned." ::={whispBoxConfig 21} scheduling OBJECT-TYPE SYNTAX INTEGER { hardware(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To use hardware or software scheduling" ::={whispBoxConfig 22} transmitterOP OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "Transmitter output power. This is not available on OFDM SMs. Not applicable for PMP 450m. See EIRP OID." ::={whispBoxConfig 23} bridgeEnable OBJECT-TYPE SYNTAX INTEGER { enable(0), disable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Disable or enable bridging functionality for a BH unit." ::={whispBoxConfig 24} fecEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Disable or enable FEC error correction functionality for multipoint units." ::={whispBoxConfig 25} trapIP1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap1." ::={whispBoxConfig 26} trapIP2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap2." ::={whispBoxConfig 27} trapIP3 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap3." ::={whispBoxConfig 28} trapIP4 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap4." ::={whispBoxConfig 29} trapIP5 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap5." ::={whispBoxConfig 30} trapIP6 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap6." ::={whispBoxConfig 31} trapIP7 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap7." ::={whispBoxConfig 32} trapIP8 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap8." ::={whispBoxConfig 33} trapIP9 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap9." ::={whispBoxConfig 34} trapIP10 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Obsoleted. Configure with whispBoxDNS.trap10." ::={whispBoxConfig 35} commStringRWrite OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Read/Write Community string. This is a write-only OID." ::={whispBoxConfig 36} subnetMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 1." ::={whispBoxConfig 37} mngtIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 1." ::={whispBoxConfig 38} allowVIDAccess OBJECT-TYPE SYNTAX INTEGER { enable(0), disable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Allow or disallow local SM management VID access." ::={whispBoxConfig 39} setDefaultPlug OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "If enabled parameters are set to Factory Defaults upon default plug mode detection." ::={whispBoxConfig 40} hwsCompatibility OBJECT-TYPE SYNTAX INTEGER { enable(0), disable(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "If enable, it ensures 6.0 compatibility with HWS." ::={whispBoxConfig 41} gpsInput OBJECT-TYPE SYNTAX INTEGER { generateSyncSignal(0), syncToReceivedSignalTimingPort(1), syncToReceivedSignalPowerPort(2), syncToiGPS(3), autoSync(4), autoSyncFreeRun(5)} MAX-ACCESS read-write STATUS current DESCRIPTION "Values 1, 2, 3 have been deprecated. (0) Generate AP sync signal. (1) Deprecated. Sync AP to received signal (Timing Port/UGPS). It will set AutoSync. (2) Deprecated. Sync AP to received signal (Power Port). It will set AutoSync plus Free Run. (3) Deprecated. Sync AP using iGPS (Only on devices which support it). It will set AutoSync plus Free Run. (4) AutoSync. (5) AutoSync plus Free Run." ::={whispBoxConfig 42} ism OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable ISM on 5.7GHz frequency band radios." ::={whispBoxConfig 43} hiPriority OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Enable Hi Priority Data Queue on BH radios." ::={whispBoxConfig 44} userName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "User name.To create read-only user set userMode OID first. Maximum of 4 users can exist in system." ::={whispBoxConfig 45} userPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "User password.To create read-only user set userMode OID first." ::={whispBoxConfig 46} userAccessLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "User access level.To create read-only user set userMode OID first. 1=TECH 2=INSTALL 3=ADMIN" ::={whispBoxConfig 47} deleteUser OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "User name to remove." ::={whispBoxConfig 48} twoXRate OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "To enable or disable double rate." ::={whispBoxConfig 49} lanDhcpState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable LAN Interface DHCP feature." ::={whispBoxConfig 50} sessionTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Timer for Telnet, Web and FTP sessions." ::={whispBoxConfig 51} vlanMemberSource OBJECT-TYPE SYNTAX INTEGER { configured(0), active(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Specified the VLAN member source to display. 0=configured, 1=active configuration. Note that this OID is internal to SNMP and is not available at the Web Interface." ::={whispBoxConfig 52} addCustomFreqList OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Add Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be added in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequency list. Max string length entered cannot exceed 128 character. Note if there is not enough room for all the frequencies none will be added. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz." ::={whispBoxConfig 53} removeCustomFreqList OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Remove Custom Frequencies. The frequencies can be in a variety of units up to KHz. Frequencies can be removed in a list separated by commas. Example: 3550, 356000, 3450001. A get will return the current custom frequencies. Only valid for use on 3.5/3.6 GHz MIMO OFDM Radios, or 450i in 4.9 GHz." ::={whispBoxConfig 54} allowColocation OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Allow or disallow Colocation for software scheduling Backhaul Timing Masters with hardware scheduling Backhaul Timing Masters." ::={whispBoxConfig 55} changeUsrPwd OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Allow to change the password of a given user of a given user. Usage: userName,password." ::={whispBoxConfig 56} -- The following definitions deal with the allowed SNMP IP & subnet masks mngtIP2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 2." ::={whispBoxConfig 57} subnetMask2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 2." ::={whispBoxConfig 58} mngtIP3 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 3." ::={whispBoxConfig 59} subnetMask3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 3." ::={whispBoxConfig 60} mngtIP4 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 4." ::={whispBoxConfig 61} subnetMask4 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 4." ::={whispBoxConfig 62} mngtIP5 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 5." ::={whispBoxConfig 63} subnetMask5 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 5." ::={whispBoxConfig 64} mngtIP6 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 6." ::={whispBoxConfig 65} subnetMask6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 6." ::={whispBoxConfig 66} mngtIP7 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 7." ::={whispBoxConfig 67} subnetMask7 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 7." ::={whispBoxConfig 68} mngtIP8 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 8." ::={whispBoxConfig 69} subnetMask8 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 8." ::={whispBoxConfig 70} mngtIP9 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 9." ::={whispBoxConfig 71} subnetMask9 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 9." ::={whispBoxConfig 72} mngtIP10 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Management IP address 10." ::={whispBoxConfig 73} subnetMask10 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Subnet mask for the management IP 10." ::={whispBoxConfig 74} bhvlanEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable VLAN for Backhaul Master/Slave." ::={whispBoxConfig 75} lldpBroadcastEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To enable Broadcast of LLDP message, if disabled LLDP uses multicast" ::={whispBoxConfig 76} regionCode OBJECT-TYPE SYNTAX INTEGER { none(0), australia(6), brazil(5), canada(3), india(8), indonesia(10), ireland(11), russia(7), spain(9), us(2), other(1), europe(4)} MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Set Region Code for the Unit. Used the individual region[Region] OIDs instead." ::={whispBoxConfig 77} russiaRegion OBJECT-TYPE SYNTAX INTEGER { category1(1), category2(2), category3(3), category4(4)} MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Set Category Region for Russian 5.9/6.05 GHz Radio Only. Use setting under regionAsia now." ::={whispBoxConfig 78} commStringROnly OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Set Read Only commnunity string." ::={whispBoxConfig 79} ethernetLinkSpeed OBJECT-TYPE SYNTAX INTEGER { forced10H(1), forced10F(2), forced100H(4), forced100F(8), auto10F-10H(3), auto100H-10H(5), auto100H-10F-10H(7), auto100F-100H(12), auto100F-100H-10H(13), auto100F-100H-10F-10H(15), auto1000F-100F-100H-10F-10H(63)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Get Ethernet link speed and duplex settings. Note that the Gigabit options are only valid for boards that support Gigabit speeds." ::={whispBoxConfig 80} cyclicPrefix OBJECT-TYPE SYNTAX INTEGER { one-quarter(0), one-eighth(1), one-sixteenth(2), one-quarter-one-eighth(3), one-quarter-one-sixteenth(4), one-eighth-one-sixteenth(5), one-quarter-one-eighth-one-sixteenth(6)} MAX-ACCESS read-write STATUS current DESCRIPTION "Cyclic Prefix value, for OFDM Radios only. Deprecated for MIMO SMs. For PMP 430 SMs, this value is only used while in PMP 430 mode (1/16 is forced in PMP 450 mode)." ::={whispBoxConfig 81} numberCustomFreq OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of custom frequencies added. There is a maximum of 100. For use on 3.5 GHz OFDM Radios only." ::={whispBoxConfig 82} channelBandwidth OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The current channel bandwidth in MHz. For use on OFDM Radios only. Obsoleted for MIMO SMs." ::={whispBoxConfig 83} setDefaults OBJECT-TYPE SYNTAX INTEGER { noChangeOrUndoFactoryDefaults(0), setToFactoryDefaults(1), factoryDefaultsSet-AwaitingReboot(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to 1 will set the radio to Factory Defaults after the next reboot. Setting this to 0 will undo Factory Defaults if and only if Factory Defaults have been set previously without rebooting. Reading this OID will return 0 if Factory Defaults are not set, or a 2 if Factory Defaults are set and we are now awaiting a reboot. NOTE: this operation is reversible as long as you write a 0 to this OID prior to reboot. As a security measure, this OID is only valid when the radio was booted in default plug mode. If the radio is not currently in default plug mode, then attempting to set this OID will fail." ::={whispBoxConfig 84} radioRateAdapt OBJECT-TYPE SYNTAX INTEGER { onex(0), onexmimo(4), onextwox(1), onextwoxmimo(5), onextwoxthreex(2), onextwoxthreexfourx(3), onextwoxfourx(7), onextwoxfourxsixx(8), onextwoxfourxsixxeightx(9), onextwoxmimoa(10), onextwoxthreexmimoa(11), onextwoxthreexfourxmimoa(12)} MAX-ACCESS read-write STATUS current DESCRIPTION "Rate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Downlink Rate Adapt only. Use radioRateAdaptUL for setting uplink rate adapt on PMP 430 radios. For PMP 450 radios, write access for engineering use only." ::={whispBoxConfig 85} siteInfoViewable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable non login users the ability to view Site Information" ::={whispBoxConfig 86} largeVCQ OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Large VC Qs for SM or PTP radios. Enable when Uplink is being used for camera video feed." ::={whispBoxConfig 87} latitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The latitude setting of this unit in decimal degrees." ::={whispBoxConfig 88} longitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The longitude setting of this unit in decimal degrees." ::={whispBoxConfig 89} height OBJECT-TYPE SYNTAX INTEGER (-2147483647..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The height setting of this unit in meters." ::={whispBoxConfig 90} bandwidth OBJECT-TYPE SYNTAX INTEGER { bandwidth5mhz(1), bandwidth7mhz(2), bandwidth10mhz(3), bandwidth15mhz(4), bandwidth20mhz(5), bandwidth30mhz(6), bandwidth40mhz(7)} MAX-ACCESS read-write STATUS current DESCRIPTION "Radio bandwidth setting. Obsoleted for MIMO SMs. Instead for MIMO SMs use OID bandwidthScan." ::={whispBoxConfig 91} dataScramblingMethod OBJECT-TYPE SYNTAX INTEGER { legacyDataScrambling(0), r10DataScrambling(1)} MAX-ACCESS read-only STATUS obsolete DESCRIPTION "This OID is for OFDM only and is obsolete." ::={whispBoxConfig 92} portVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Backhaul Port VID (PVID)." ::={whispBoxConfig 93} radioRateAdaptUL OBJECT-TYPE SYNTAX INTEGER { onex(0), onexmimo(4), onextwox(1), onextwoxmimo(5), onextwoxthreex(2), onextwoxthreexfourx(3), onextwoxfourx(7), onextwoxfourxsixx(8), onextwoxfourxsixxeightx(9), onextwoxmimoa(10), onextwoxthreexmimoa(11), onextwoxthreexfourxmimoa(12)} MAX-ACCESS read-write STATUS current DESCRIPTION "Uplink Rate adaptation parameter 0: 1x No rate adaptation (FSK and SISO OFDM QPSK) 1: 1x/2x (FSK and SISO OFDM 16-QAM) Following are OFDM only: 2: 1x/2x/3x (SISO OFDM 64-QAM) 3: 1x/2x/3x/4x (SISO OFDM 256-QAM) Engineering only Following are MIMO OFDM only: 4: 1x MIMO-A (QPSK duplicated on both paths) 5: 1x/2x MIMO-B (QPSK on each path) 7: 1x/2x/4x MIMO-B (16-QAM on each path) 8: 1x/2x/4x/6x MIMO-B (64-QAM on each path) 9: 1x/2x/4x/6x/8x MIMO-B (256-QAM on each path) 10: 1x/2x MIMO-A (16-QAM duplicated on both paths) 11: 1x/2x/3x MIMO-A (64-QAM duplicated on both paths) 12: 1x/2x/3x/4x MIMO-A (256-QAM duplicated on both paths) For PMP 430 radios this applies to Uplink Rate Adapt only. Use radioRateAdapt for setting downlink rate adapt on PMP 430 radios. For PMP 450 radios, engineering use only." ::={whispBoxConfig 94} providerVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Provider VID for QinQ VLAN." ::={whispBoxConfig 95} mac1VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 1 in MAC Address VID Mapping Table." ::={whispBoxConfig 96} mac1VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 1 in MAC Address VID Mapping Table." ::={whispBoxConfig 97} mac2VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 2 in MAC Address VID Mapping Table." ::={whispBoxConfig 98} mac2VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 2 in MAC Address VID Mapping Table." ::={whispBoxConfig 99} mac3VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 3 in MAC Address VID Mapping Table." ::={whispBoxConfig 100} mac3VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 3 in MAC Address VID Mapping Table." ::={whispBoxConfig 101} mac4VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 4 in MAC Address VID Mapping Table." ::={whispBoxConfig 102} mac4VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 4 in MAC Address VID Mapping Table." ::={whispBoxConfig 103} mac5VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 5 in MAC Address VID Mapping Table." ::={whispBoxConfig 104} mac5VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 5 in MAC Address VID Mapping Table." ::={whispBoxConfig 105} mac6VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 6 in MAC Address VID Mapping Table." ::={whispBoxConfig 106} mac6VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 6 in MAC Address VID Mapping Table." ::={whispBoxConfig 107} mac7VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 7 in MAC Address VID Mapping Table." ::={whispBoxConfig 108} mac7VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 7 in MAC Address VID Mapping Table." ::={whispBoxConfig 109} mac8VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 8 in MAC Address VID Mapping Table." ::={whispBoxConfig 110} mac8VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 8 in MAC Address VID Mapping Table." ::={whispBoxConfig 111} mac9VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 9 in MAC Address VID Mapping Table." ::={whispBoxConfig 112} mac9VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 9 in MAC Address VID Mapping Table." ::={whispBoxConfig 113} mac10VIDMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC Address for Entry 10 in MAC Address VID Mapping Table." ::={whispBoxConfig 114} mac10VIDMapVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VID for Entry 10 in MAC Address VID Mapping Table." ::={whispBoxConfig 115} vlanPortType OBJECT-TYPE SYNTAX INTEGER { q(0), qinq(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN Port Type for VLAN interface. Default is Q." ::={whispBoxConfig 116} vlanAcceptQinQFrames OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Allow/Disallow packets already doubly-tagged (QinQ) to ingress the FEC of BHM, BHS, or MP SM. Not configurable on MP AP." ::={whispBoxConfig 117} whispWebUserAccessMode OBJECT-TYPE SYNTAX INTEGER { local(0), remote(1), remotethenlocal(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable selects if web page users for the radio should be authenticated locally or via a centralised remote Radius server" ::={whispBoxConfig 118} usrAccountEnableAccounting OBJECT-TYPE SYNTAX INTEGER { disable(0), deviceAccess(1), dataUsage(2), all(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Select the level of accounting information to be reported to the server" ::={whispBoxConfig 119} allowRejectThenLocal OBJECT-TYPE SYNTAX INTEGER { doNotAllowLocalAuthifAAAReject(0), allowLocalAuthIfAAAReject(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Control for allowing local authenication if the AAA remote server" ::={whispBoxConfig 120} snrCalculation OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This OID is deprecated. Receive quality calulation is always on since it no longer affects packet per second performance." ::={whispBoxConfig 121} priorityPrecedence OBJECT-TYPE SYNTAX INTEGER { eight021pThenDiffServ(0), diffservThenEight021p(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Allows user to decide if 802.1p or DiffServ priority bits should be used first when making priority decisions." ::={whispBoxConfig 122} installationColorCode OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Installation Color Code. Allows non-configured SMs to register to an AP with UCC enabled in order to facilitate remote provisioning." ::={whispBoxConfig 123} apSmMode OBJECT-TYPE SYNTAX INTEGER { sm(1), ap(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set AP to SM or SM to AP. Useful for facillitating scripting of running Spectrum Analyzer on an AP. Radio must have AP Feature Key. 1 - Set to SM, 0 - Set to AP." ::={whispBoxConfig 124} pppoeFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set PPPoE packet filter." ::={whispBoxConfig 125} smbFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set SMB packet filter." ::={whispBoxConfig 126} snmpFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set SNMP packet filter." ::={whispBoxConfig 127} userP1Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 1 packet filter." ::={whispBoxConfig 128} userP2Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 2 packet filter." ::={whispBoxConfig 129} userP3Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 3 packet filter." ::={whispBoxConfig 130} allOtherIpFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set all other IPv4 packet filter." ::={whispBoxConfig 131} allIpv4Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set all IPv4 packet filter. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4)." ::={whispBoxConfig 132} arpFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set ARP packet filter." ::={whispBoxConfig 133} allOthersFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set all other packet filter when." ::={whispBoxConfig 134} -- User Defined Port Filtering Configuration userDefinedPort1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "An integer value of number one user defined port. Range:0-65535" ::={whispBoxConfig 135} port1TCPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 1 TCP traffic filter." ::={whispBoxConfig 136} port1UDPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 1 UDP traffic filter." ::={whispBoxConfig 137} userDefinedPort2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "An integer value of number two user defined port. Range:0-65535" ::={whispBoxConfig 138} port2TCPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 2 TCP traffic filter." ::={whispBoxConfig 139} port2UDPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 2 UDP traffic filter." ::={whispBoxConfig 140} userDefinedPort3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "An integer value of number three user defined port. Range:0-65535" ::={whispBoxConfig 141} port3TCPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 3 TCP traffic filter." ::={whispBoxConfig 142} port3UDPFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set user defined port 3 UDP traffic filter." ::={whispBoxConfig 143} bootpcFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set bootp client sourced packets filter." ::={whispBoxConfig 144} bootpsFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set bootp server sourced packets filter." ::={whispBoxConfig 145} ip4MultFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv4 MultiCast packets filter when NAT is disabled." ::={whispBoxConfig 146} packetFilterDirection OBJECT-TYPE SYNTAX INTEGER { upstream(1), downstream(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set packet filter direction. Upstream is default." ::={whispBoxConfig 147} encryptionConfig OBJECT-TYPE SYNTAX INTEGER { des(0), aes(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "For supported radio, set the encryption algorithm to use. DES by default. Cannot be set if encryption is disabled." ::={whispBoxConfig 148} pppoeCtlPriority OBJECT-TYPE SYNTAX INTEGER { normal(0), high(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Prioritization of PPPoE Control packets." ::={whispBoxConfig 149} ftpPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Port used to for FTP. Default is 21." ::={whispBoxConfig 150} httpPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Port used to for HTTP. Default is 80." ::={whispBoxConfig 151} httpsPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Port used to for HTTPs. Default is 443." ::={whispBoxConfig 152} snmpPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Port used to for SNMP. Default is 161." ::={whispBoxConfig 153} snmpTrapPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Port used to for SNMP Traps. Default is 162." ::={whispBoxConfig 154} webAccess OBJECT-TYPE SYNTAX INTEGER { http(0), https(1), http-and-https(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines if only HTTP or HTTPs connection are allowed. 0: HTTP Only 1: HTTPs Only 2: HTTP and HTTPs Both" ::={whispBoxConfig 155} syslogDomainNameAppend OBJECT-TYPE SYNTAX INTEGER { disableDomain(0), appendDomain(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Select whether to append the configured management domain name to the Syslog server name. For example, if dnsMgmtDomainName is set to 'example.com', syslogServerAddr is set to 'syslog1', and syslogDomainNameAppend is set to appendDomain, the Syslog Server name used would be 'syslog1.example.com'." ::={whispBoxConfig 156} syslogServerAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Syslog server address either in dotted decimal notation or a Fully Qualified Domain Name" ::={whispBoxConfig 157} syslogServerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Listening port on the Syslog server. Default is 514." ::={whispBoxConfig 158} syslogMinLevel OBJECT-TYPE SYNTAX INTEGER { fatal(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)} MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the minimum syslog severity to transmit. Messages with a lower severity value (i.e. numerically higher) than this will not be transmitted." ::={whispBoxConfig 159} allIpv6Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set all IPv6 packet filter. Enabling this will automatically enable all of the known IPv6 filters (SMB, SNMP, Bootp, IPv6 Mcast, User Defined Ports, and All Other IPv6)." ::={whispBoxConfig 160} ipv6smbFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv6 SMB packet filter." ::={whispBoxConfig 161} ipv6snmpFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv6 SNMP packet filter." ::={whispBoxConfig 162} ipv6bootpcFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv6 bootp client sourced packets filter." ::={whispBoxConfig 163} ipv6bootpsFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv6 bootp server sourced packets filter." ::={whispBoxConfig 164} ipv6MultFilter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set IPv6 MultiCast packets filter when NAT is disabled." ::={whispBoxConfig 165} allOtherIpv6Filter OBJECT-TYPE SYNTAX INTEGER { filterOff(0), filterOn(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To set all other IPv6 packet filter." ::={whispBoxConfig 166} snmpStatus OBJECT-TYPE SYNTAX INTEGER { snmpv2only(1), snmpv3only(2), snmpv2-and-snmpv3(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines SNMP operation mode. 1: Enable SNMPv2c only 2: Enable SNMPv3 only 3: Enable SNMPv2c and SNMPv3" ::={whispBoxConfig 167} telnetStatus OBJECT-TYPE SYNTAX INTEGER { disabletelnet(0), enabletelnet(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines if Telnet to enabled or not. 0: Disable Telnet 1: Enable Telnet" ::={whispBoxConfig 168} ftpStatus OBJECT-TYPE SYNTAX INTEGER { disableftp(0), enableftp(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines if FTP to enabled or not. 0: Disable FTP 1: Enable FTP" ::={whispBoxConfig 169} tftpStatus OBJECT-TYPE SYNTAX INTEGER { disabletftp(0), enabletftp(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "This variable determines if TFTP is enabled or not. 0: Disable TFTP 1: Enable TFTP" ::={whispBoxConfig 170} userMode OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "User Mode 1=Read-Only 0=Read-Write(default)." ::={whispBoxConfig 171} tcpAckPriority OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Prioritize TCP ACK that are 64 bytes or less." ::={whispBoxConfig 172} codePointSelect OBJECT-TYPE SYNTAX INTEGER { cp1(1), cp2(2), cp3(3), cp4(4), cp5(5), cp6(6), cp7(7), cp8(8), cp9(9), cp10(10), cp11(11), cp12(12), cp13(13), cp14(14), cp15(15), cp16(16), cp17(17), cp18(18), cp19(19), cp20(20), cp21(21), cp22(22), cp23(23), cp24(24), cp25(25), cp26(26), cp27(27), cp28(28), cp29(29), cp30(30), cp31(31), cp32(32), cp33(33), cp34(34), cp35(35), cp36(36), cp37(37), cp38(38), cp39(39), cp40(40), cp41(41), cp42(42), cp43(43), cp44(44), cp45(45), cp46(46), cp47(47), cp49(49), cp50(50), cp51(51), cp52(52), cp53(53), cp54(54), cp55(55), cp57(57), cp58(58), cp59(59), cp60(60), cp61(61), cp62(62), cp63(63)} MAX-ACCESS read-write STATUS current DESCRIPTION "Codepoint Select.This represents the CodePoint Selection to be modified via Priority Select" ::={whispBoxConfig 173} prioritySelect OBJECT-TYPE SYNTAX INTEGER { p0(0), p1(1), p2(2), p3(3), p4(4), p5(5), p6(6), p7(7)} MAX-ACCESS read-write STATUS current DESCRIPTION "Priority Select.The priority setting input for the CodePoint selected in CodePoint Select." ::={whispBoxConfig 174} auxPortEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable(1) or Disable(0) aux ethernet port on 450i radio" ::={whispBoxConfig 175} poeAuxEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable(1) or Disable(0) aux ethernet port PoE on 450i radio" ::={whispBoxConfig 176} whispUsrAuth OBJECT-TYPE SYNTAX INTEGER { md5(0), peap-mschapv2(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Select method for User Authentication." ::={whispBoxConfig 177} lan1DhcpRelease OBJECT-TYPE SYNTAX INTEGER { releaseIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will release LAN1's IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is disabled." ::={whispBoxConfig 201} lan1DhcpRenew OBJECT-TYPE SYNTAX INTEGER { renewIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will renew LAN1's lease time for its current IP address. Applicable only when NAT is disabled." ::={whispBoxConfig 202} lan3DhcpRelease OBJECT-TYPE SYNTAX INTEGER { releaseIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will release LAN3's (RF Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled." ::={whispBoxConfig 203} lan3DhcpRenew OBJECT-TYPE SYNTAX INTEGER { renewIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will renew LAN3's (RF Public) lease time for its current IP address. Applicable only when NAT is enabled." ::={whispBoxConfig 204} natDhcpRelease OBJECT-TYPE SYNTAX INTEGER { releaseIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will release WAN's (NAT Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled." ::={whispBoxConfig 205} natDhcpRenew OBJECT-TYPE SYNTAX INTEGER { renewIP(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to '1' will renew WAN's (NAT Public) lease time for its current IP address. Applicable only when NAT is enabled." ::={whispBoxConfig 206} region OBJECT-TYPE SYNTAX INTEGER { none(0), otherRegulatory(1), asia(6), europe(3), northAmerica(2), oceania (5), southAmerica(4), africa(7)} MAX-ACCESS read-only STATUS current DESCRIPTION "Set Region Code for the Unit." ::={whispBoxConfig 207} regionAsia OBJECT-TYPE SYNTAX INTEGER { none(0), india(2), indonesia(3), russiacategory1(4), russiacategory2(5), russiacategory3(6), russiacategory4(7), vietnam(8), malaysia(10), pakistan(11)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for Asia." ::={whispBoxConfig 208} regionEurope OBJECT-TYPE SYNTAX INTEGER { none(0), spain(2), ireland(3), denmark(4), finland(5), germany(6), greece(7), iceland(8), liechtenstein(9), norway(10), portugal(11), switzerland(12), serbia(13), unitedkingdom(14), other(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for Europe. Other is only available for units with EU Region Lock." ::={whispBoxConfig 209} regionNorthAmerica OBJECT-TYPE SYNTAX INTEGER { none(0), canada(3), unitedStates(2), mexico(4), puertoRico(5)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for North America." ::={whispBoxConfig 210} regionOceania OBJECT-TYPE SYNTAX INTEGER { none(0), australia(2), newZealand(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for Oceania." ::={whispBoxConfig 211} regionSouthAmerica OBJECT-TYPE SYNTAX INTEGER { none(0), brazil(2), ecuador(3), colombia(4), venezuela(5), panama(6)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for South America." ::={whispBoxConfig 212} regionOtherRegulatory OBJECT-TYPE SYNTAX INTEGER { none(0), other(1), fcc(2), etsi(3), etsilbt(4)} MAX-ACCESS read-write STATUS current DESCRIPTION "Regulatory setting for governing regulatory body." ::={whispBoxConfig 213} interleave OBJECT-TYPE SYNTAX INTEGER { default(0), disabled(1), enabled(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Engineering use only." ::={whispBoxConfig 214} receiveQualityDebug OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable receive quality calculations for every packet. Enabling(1) will calulate receive quality on all receiving packets. Due to load on CPU, will slightly packet per second capabilities on AP/BH. Default to disabled for all radios. Only applicable to GenII OFDM products and up." ::={whispBoxConfig 215} apType OBJECT-TYPE SYNTAX INTEGER { standard(0), remote(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "In standard mode, all possible sync sources will be made availble and usedfor autoSync operation. In remote mode, sync over power port will not be available as a sync source. Remote Device mode is where the AP or BHM timing port is connected to an SM or BHS timing port via a sync cable. In this mode, GPS data is unavailable and sync over power port shouldn't be used. If sync over power is desired, and a CMM or other sync over power device is in use, then select standard mode. This should really be named deviceType because this applies to both AP and BHM, but left this as apType for legacy purposes." ::={whispBoxConfig 216} regionAfrica OBJECT-TYPE SYNTAX INTEGER { none(0), algeria(2), nigeria(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Country Code for Africa." ::={whispBoxConfig 217} addCustomFreqMimo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency input ie) 3700.50. Deprecated, please use 'addCustomFreqList'." ::={whispBoxConfig 218} removeCustomFreqMimo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Frequency input ie) 3700.50. Deprecated, please use 'removeCustomFreqList'." ::={whispBoxConfig 219} timedSpectrumAnalysisDurationBox OBJECT-TYPE SYNTAX INTEGER (10..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds." ::={whispBoxConfig 220} spectrumAnalysisActionBox OBJECT-TYPE SYNTAX INTEGER { stopSpectrumAnalysis(0), startTimedSpectrumAnalysis(1), startContinuousSpectrumAnalysis(2), idleNoSpectrumAnalysis(3), idleCompleteSpectrumAnalysis(4), inProgressTimedSpectrumAnalysis(5), inProgressContinuousSpectrumAnalysis(6), notReady(7)} MAX-ACCESS read-write STATUS current DESCRIPTION "Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis Note: AP/BHM will run Spectrum Analysis for the sector. (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours. (7) - Spectrum Analyzer not ready." ::={whispBoxConfig 221} mac1VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 1 in MAC Address VID Mapping Table." ::={whispBoxConfig 222} mac1VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 1 in MAC Address VID Mapping Table." ::={whispBoxConfig 223} mac2VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 2 in MAC Address VID Mapping Table." ::={whispBoxConfig 224} mac2VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 2 in MAC Address VID Mapping Table." ::={whispBoxConfig 225} mac3VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 3 in MAC Address VID Mapping Table." ::={whispBoxConfig 226} mac3VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 3 in MAC Address VID Mapping Table." ::={whispBoxConfig 227} mac4VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 4 in MAC Address VID Mapping Table." ::={whispBoxConfig 228} mac4VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 4 in MAC Address VID Mapping Table." ::={whispBoxConfig 229} mac5VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 5 in MAC Address VID Mapping Table." ::={whispBoxConfig 230} mac5VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 5 in MAC Address VID Mapping Table." ::={whispBoxConfig 231} mac6VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 6 in MAC Address VID Mapping Table." ::={whispBoxConfig 232} mac6VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 6 in MAC Address VID Mapping Table." ::={whispBoxConfig 233} mac7VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 7 in MAC Address VID Mapping Table." ::={whispBoxConfig 234} mac7VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 7 in MAC Address VID Mapping Table." ::={whispBoxConfig 235} mac8VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 8 in MAC Address VID Mapping Table." ::={whispBoxConfig 236} mac8VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 8 in MAC Address VID Mapping Table." ::={whispBoxConfig 237} mac9VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 9 in MAC Address VID Mapping Table." ::={whispBoxConfig 238} mac9VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 9 in MAC Address VID Mapping Table." ::={whispBoxConfig 239} mac10VIDMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority for Entry 10 in MAC Address VID Mapping Table." ::={whispBoxConfig 240} mac10VIDMapPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "VID priority Mode for Entry 10 in MAC Address VID Mapping Table." ::={whispBoxConfig 241} managementVIDPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "management VID VID VLAN Priority." ::={whispBoxConfig 242} managementVIDPriorityMode OBJECT-TYPE SYNTAX INTEGER { promote-IP-priority(0), define-priority(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "management VID VLAN Priority Mode." ::={whispBoxConfig 243} remarkSrcVID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Source VID to apply remarking on." ::={whispBoxConfig 244} addRemarkVID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Add VLAN ID re-marking entry." ::={whispBoxConfig 245} addRemarkPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Add 802.1p re-mark entry." ::={whispBoxConfig 246} deleteRemarkVID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Remove the VID re-marking for this source VID." ::={whispBoxConfig 247} deleteRemarkPriority OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Remove the priority re-marking for this source VID." ::={whispBoxConfig 248} mimoRateAdaptAlgorithm OBJECT-TYPE SYNTAX INTEGER { mimobmimoa(0), mimobonly(1), mimoaonly(2), siso(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Engineering use only. Control MIMO Rate Adapt Algorithm 0 = MIMO-A/B This chooses MIMO-A or MIMO-B dynamically to maximize throughput 1 = MIMO-B only 2 = MIMO-A only 3 = SISO only" ::={whispBoxConfig 249} controlMessages OBJECT-TYPE SYNTAX INTEGER { siso(1), mimoa(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Control Messages (Beacon/Scheduling Map/Acknowledgements/Broadcast) 0 = MIMO-A 1 = SISO MIMO Control Messages is the recommended and default setting. However, SISO Control Messages can be helpful in talking to subscribers on releases previous to 13.2, which operated in this mode. Not applicable to PMP 450m." ::={whispBoxConfig 250} enableSecurityBanner OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Shows Security Banner at the time of login" ::={whispBoxConfig 251} vcDepth OBJECT-TYPE SYNTAX INTEGER { default(0), eight(8), sixteen(16), thirty-two(32), sixty-four(64), one-two-eight(128)} MAX-ACCESS read-write STATUS current DESCRIPTION "VC Depth of radio. Not applicable with 450m. Engineering use only." ::={whispBoxConfig 252} textSecurityBanner OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Security Banner to be dispalyed on login page. Length should be maximum 1200 characters.Configuration from web UI can enter upto 1499 characters. Only ASCII characters(0-9a-zA-Z,CR,LF) supported." ::={whispBoxConfig 253} acceptSecurityBanner OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "1: User must accept and acknowledge security banner before login. 0: Accepting security banner is not mandatory and user can login without it." ::={whispBoxConfig 254} poeT2Classification OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "When disabled, the radio will ignore the 802.3at Type 2 classification. When enabled, if 802.3at Type 2 PoE is not present, the board will start and log the problem but the transmitter and PoE out will not be enabled due to the low input power. This is only available on the 450i." ::={whispBoxConfig 255} simulatedAirDelay OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Simulated Air Delay. Engineering use only." ::={whispBoxConfig 256} cnMaestroEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Remote management using cnMaestro." ::={whispBoxConfig 257} cnMaestroUrl OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "cnMaestro Server URL." ::={whispBoxConfig 258} camID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Cambium Id for cnMaestro onboarding." ::={whispBoxConfig 259} camOnboardKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Onboarding key for cnMaestro onboarding." ::={whispBoxConfig 260} atexHazlocPowerLimit OBJECT-TYPE SYNTAX INTEGER { gasGroupA(0), gasGroupB(1), gasGroupC(2), gasGroupD(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "If radio is keyed for ATEX/HazLoc operation, these settings can be used to limit maximum power output, per Gas Group specs." ::={whispBoxConfig 261} nearFieldRange OBJECT-TYPE SYNTAX INTEGER (6..3000) UNITS "feet" MAX-ACCESS read-write STATUS current DESCRIPTION "Range in feet for near field operation. This is applied only when nearFieldOperation is set to enable(1) and eirp is 22dBm or below or when Engineering keyed. The maximum range of 3000ft applies negligible correction. PMP 450m only." ::={whispBoxConfig 262} nearFieldOperation OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enables operation in the near field. This is effective only when an EIRP of 22 dBm or lower is selected or when Engineering keyed. PMP 450m only." ::={whispBoxConfig 263} defaultIPAccessEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable(1) or Disable(0) Default alternative LAN1 IP address" ::={whispBoxConfig 264} pingWdogEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "enable(1) or disable(0) ping watchdog." ::={whispBoxConfig 265} pingWdogIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IPv4 address to ping in dotted decimal notation." ::={whispBoxConfig 266} pingWdogInterval OBJECT-TYPE SYNTAX INTEGER (300..86400) UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Intervals in seconds at which ping should be initiated." ::={whispBoxConfig 267} pingWdogRbtCnt OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Ping Failures count at which reboot should be initiated." ::={whispBoxConfig 268} forceReassessment OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Forces channel reassessment for all registered SMs. This is effective only when an EIRP of 22 dBm or lower is selected or when Engineering keyed. MU-MIMO only." ::={whispBoxConfig 275} enable8023linkBox OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable 802.3 link." ::={whispBoxConfig 276} ethernetPortSelection OBJECT-TYPE SYNTAX INTEGER { mainPort(0), sfpPort(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Get the Ethernet port used to bridge traffic. PMP 450m only." ::={whispBoxConfig 278} ethernetLinkSpeedSfp OBJECT-TYPE SYNTAX INTEGER { auto1000FX(32), auto1000F-100F(40), forced1000FX(64), auto2500F-1000F-100F(168)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set/Get Ethernet link speed and duplex settings of the SFP port. PMP 450m only. Please note that the Radio Recovery Console only supports auto1000F for the SFP." ::={whispBoxConfig 279} -- Box level control. saveFlash OBJECT-TYPE SYNTAX INTEGER { doNotSaveToFlash(0), saveToFlash(1)} MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This variable is currently deprecated." ::={whispBoxControls 1} reboot OBJECT-TYPE SYNTAX INTEGER { finishedReboot(0), reboot(1), fullReboot(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to 1 will reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Setting the variable to 2 will perform a full reboot of a 450i radio, while performing a normal reboot on other radios." ::={whispBoxControls 2} clearEventLog OBJECT-TYPE SYNTAX INTEGER { notClear(0), clear(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to 1 will clear the event log." ::={whispBoxControls 3} rebootIfRequired OBJECT-TYPE SYNTAX INTEGER { rebootNotRequired(0), rebootRequired(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the variable to 1 will reboot the unit if reboot is required." ::={whispBoxControls 4} clearBERStats OBJECT-TYPE SYNTAX INTEGER { doNotClearBERStats(0), clearBERStats(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set to clear the BER statistics by sending a 'clearBERStats'. Value is set back to 'doNotClearBERStats' When action is complete." ::={whispBoxControls 5} updateDevice OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Use to update the software on the device" ::={whispBoxControls 6} importConfigFile OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Set to URL to immediately download and apply configuration file" ::={whispBoxControls 7} exportConfigFile OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Set to URL to immediately export and upload configuration file" ::={whispBoxControls 8} undoUnitWideSavedChanges OBJECT-TYPE SYNTAX INTEGER { undoUnitWideSavedChanges(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting to 1 will undo unit wide saved changes" ::={whispBoxControls 9} resetPoEAux OBJECT-TYPE SYNTAX INTEGER { reset(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting to 1 will reset aux ethernet port PoE on 450i radio. Port will be powered off for 2 seconds during the set call, which will delay the SNMP response." ::={whispBoxControls 10} whispBoxEvntLog OBJECT-TYPE SYNTAX EventString MAX-ACCESS read-only STATUS current DESCRIPTION "Event log for AP and SM." ::={whispBoxEventLog 1} whispBoxAttributesGroup OBJECT-GROUP OBJECTS { vlanAcceptQinQFrames, providerVID, mac1VIDMapAddr, mac1VIDMapVid, mac1VIDMapPriority, mac1VIDMapPriorityMode, mac2VIDMapAddr, mac2VIDMapVid, mac2VIDMapPriority, mac2VIDMapPriorityMode, mac3VIDMapAddr, mac3VIDMapVid, mac3VIDMapPriority, mac3VIDMapPriorityMode, mac4VIDMapAddr, mac4VIDMapVid, mac4VIDMapPriority, mac4VIDMapPriorityMode, mac5VIDMapAddr, mac5VIDMapVid, mac5VIDMapPriority, mac5VIDMapPriorityMode, mac6VIDMapAddr, mac6VIDMapVid, mac6VIDMapPriority, mac6VIDMapPriorityMode, mac7VIDMapAddr, mac7VIDMapVid, mac7VIDMapPriority, mac7VIDMapPriorityMode, mac8VIDMapAddr, mac8VIDMapVid, mac8VIDMapPriority, mac8VIDMapPriorityMode, mac9VIDMapAddr, mac9VIDMapVid, mac9VIDMapPriority, mac9VIDMapPriorityMode, mac10VIDMapAddr, mac10VIDMapVid, mac10VIDMapPriority, mac10VIDMapPriorityMode, vlanPortType, portVID, timedSpectrumAnalysisDurationBox, spectrumAnalysisActionBox, calibrationStatusBox, calibrationStatusBool, catalinaGainRxCH1, catalinaGainRxCH2, catalinaAttenTxCH1, catalinaAttenTxCH2, catalinaCurrDetSetpointTxCH1, catalinaCurrDetSetpointTxCH2, catalinaCurrDetReadRefTxCH1, catalinaCurrDetReadRefTxCH2, catalinaCurrDetReadPowerOnTxCH1, catalinaCurrDetReadPowerOnTxCH2, catalinaOpenLoopAttenTxCH1, catalinaOpenLoopAttenTxCH2, catalinaTargetDetSetpointTxCH1, catalinaTargetDetSetpointTxCH2, catalinaGainReductionRxCH1, catalinaGainReductionRxCH2, catalinaLoAttenRxCH1, catalinaLoAttenRxCH2, catalinaTargetGainRxCH1, catalinaTargetGainRxCH2, whispBoxSoftwareVer, whispBoxFPGAVer, whispBoxEsn, whispBoxBoot, boxTemperature, boxDeviceType, boxDeviceTypeID, boxEncryption, etherLinkStatus, boxFrequency, platformVer, platformType, dhcpLanIp, dhcpLanSubnetMask, dhcpLanGateway, dhcpRfPublicIp, dhcpRfPublicSubnetMask, dhcpRfPublicGateway, lanDhcpStatus, rfPublicDhcpStatus, natDhcpStatus, inSyncCount, outSyncCount, pllOutLockCount, txCalFailure, swVersion, pldVersion, platformInfo, antType, antPolarization, whispBoxP11Personality, whispBoxP11FPGAType, whispBoxP11BstrapFPGAVer, numDFSDetections, numLBTDetections, rxOverrunPkts, boxTemperatureC, boxTemperatureF, linkNegoSpeed, installationColorCode, colorCode, displayOnlyAccess, fullAccess, webAutoUpdate, pass1Status, pass2Status, bridgeEntryTimeout, cnMaestroEnable, cnMaestroUrl, camID, camOnboardKey, camAccID, cnMaestroStatus, daVersion, snmpMibPerm, bhTimingMode, powerControl, extFilterDelay, antennaGain, eirp, dynamicLearning, managementVID, managementVIDPriority, managementVIDPriorityMode, agingTimeout, remarkSrcVID, addRemarkVID, addRemarkPriority, deleteRemarkVID, deleteRemarkPriority, frameType, addVlanMember, removeVlanMember, scheduling, transmitterOP, bridgeEnable, fecEnable, trapIP1, trapIP2, trapIP3, trapIP4, trapIP5, trapIP6, trapIP7, trapIP8, trapIP9, trapIP10, commStringRWrite, subnetMask, mngtIP, allowVIDAccess, setDefaultPlug, hwsCompatibility, gpsInput, ism, hiPriority, userName, userPassword, userAccessLevel, userMode, deleteUser, twoXRate, lanDhcpState, dnsIpState, sessionTimeout, vlanMemberSource, addCustomFreqList, removeCustomFreqList, allowColocation, changeUsrPwd, mngtIP2, subnetMask2, mngtIP3, subnetMask3, mngtIP4, subnetMask4, mngtIP5, subnetMask5, mngtIP6, subnetMask6, mngtIP7, subnetMask7, mngtIP8, subnetMask8, mngtIP9, subnetMask9, mngtIP10, subnetMask10, bhvlanEnable, lldpBroadcastEnable, radioRateAdapt, boardModel, productTypeName, fpgaBuildDate, fpgaCompileInfo, syslogDomainNameAppend, syslogServerAddr, syslogServerPort, syslogMinLevel, pingWdogEnable, pingWdogIP, pingWdogInterval, pingWdogRbtCnt, syslogStatTxSuccesses, syslogStatDropped, apType, apSmMode, region, regionCode, regionAsia, regionEurope, regionNorthAmerica, regionOceania, regionSouthAmerica, regionAfrica, regionOtherRegulatory, mimoRateAdaptAlgorithm, radioRateAdaptUL, tcpAckPriority, dnsPrimaryMgmtIP, dnsAlternateMgmtIP, dnsMgmtDomainName, auxPortEnable, defaultIPAccessEnable, poeAuxEnable, addCustomFreqMimo, removeCustomFreqMimo, snmpv2cEnable, nearFieldRange, nearFieldOperation, nearFieldOperationActive, forceReassessment, forceReassessmentActive, ftpPort, httpPort, httpsPort, snmpPort, snmpTrapPort, webAccess, snmpStatus, telnetStatus, ftpStatus, tftpStatus, lan1DhcpRelease, lan1DhcpRenew, lan3DhcpRelease, lan3DhcpRenew, natDhcpRelease, natDhcpRenew, radioEngKeyed, radioWatchDogLogged, radioFatalErrorLogged, codePointSelect, prioritySelect, priorityPrecedence, pppoeCtlPriority, rfStatXmtUDataCnt, rfStatXmtBDataCnt, rfStatXmtMDataCnt, rfStatRcvUDataCnt, rfStatRcvBDataCnt, rfStatRcvMDataCnt, rfStatXmtCntlCnt, rfStatRcvCntlCnt, rfStatInSyncCount, rfStatOutSyncCount, rfStatOverrunCount, rfStatUnderrunCount, rfStatRcvCorruptDataCount, rfStatRcvCorruptControlCount, rfStatBadBcastCtlCnt, rfStatPLLOutOfLockCnt, rfStatBeaconVerMismatchCnt, rfStatBadFreqBcnRcvCnt, rfStatnonLiteBcnRcvCnt, rfStatUnsupFeatBcnRcvCnt, rfStatUnkwnFeatBcnRcvCnt, rfStatTxCalFailCnt, rfStatBadInSyncIDRcv, rfStatTempOutOfRange, rfStatRSSIOutOfRange, rfStatRangeCapEnf, rfStatRcvLTStart, rfStatRcvLTStartHS, rfStatRcvLTResult, rfStatXmtLTResult, soundingStatClear, soundingStatRequestCount, soundingStatResponseCount, soundingStatRequestsIgnored, soundingStatAvgRequestInterval, soundingStatMaxRequestInterval, soundingStatErrorCount, soundingStatRequestsDropped, soundingStatResponsesSuppressed, soundingStatVersionMismatch, whispFeatureKeyOrigin, poeT2Status, updateStatus, bridgeCbFecStatbin, bridgeCbFecStatbout, bridgeCbFecStatbtoss, bridgeCbFecStatbtosscap, bridgeCbFecStatuin, bridgeCbFecStatuout, bridgeCbFecStatutoss, bridgeCbFecStatutosscap, bridgeCbEthAuxStatbin, bridgeCbEthAuxStatbout, bridgeCbEthAuxStatbtoss, bridgeCbEthAuxStatbtosscap, bridgeCbEthAuxStatuin, bridgeCbEthAuxStatuout, bridgeCbEthAuxStatutoss, bridgeCbEthAuxStatutosscap, bridgeCbFecStatfloods, bridgeCbEthAuxStatfloods, bridgeCbRFStatfloods, bridgeCbRFStatbin, bridgeCbRFStatbout, bridgeCbRFStatbtoss, bridgeCbRFStatbtosscap, bridgeCbRFStatuin, bridgeCbRFStatuout, bridgeCbRFStatutoss, bridgeCbRFStatutosscap, bridgeCbErrStatNI1QSend, bridgeCbErrStatNI2QSend, bridgeCbErrStatBridgeFull, bridgeCbErrStatSendMsg, bridgeCbErrStatAPFecQSend, bridgeCbErrStatApRfQSend, fecStatLinkDetected, fecStatLinkUptime, fecStatLinkLost, fecStatUnderSizedToss, fecInDiscardsCount, fecInErrorsCount, fecOutDiscardsCount, fecOutErrorsCount, fecRxBabErr, fecTxHbErr, fecEthBusErr, fecCRCError, fecRxFifoNoBuf, fecRxOverrun, fecLateCollision, fecRetransLimitExp, fecTxUnderrun, fecCarSenseLost, fecNoCarrier, fecLargeFrame, fecRuntFrame, fecExcessiveDeferrals, fecAuxStatLinkDetected, fecAuxStatLinkUptime, fecAuxStatLinkLost, fecAuxInDiscardsCount, fecAuxInErrorsCount, fecAuxOutDiscardsCount, fecAuxOutErrorsCount, fecAuxCRCError, fecAuxRxOverrun, fecAuxLateCollision, fecAuxRetransLimitExp, fecAuxTxUnderrun, fecAuxCarSenseLost, fecAuxNoCarrier, fecAuxLargeFrame, fecAuxRuntFrame, rfInDiscardsCountExt, rfInErrorsCountExt, rfOutDiscardsCountExt, rfOutErrorsCountExt, rfInDiscardsCount, rfInErrorsCount, rfOutDiscardsCount, rfOutErrorsCount, packetOverloadCounter, fecInDiscardsOverloadCount, fecOutDiscardsOverloadCount, rfInDiscardsOverloadCount, rfOutDiscardsOverloadCount, framePeriodCurrent, hardwareVersion, radioStatusTransmitControlOverridden, radioStatusTrackingFailure, radioStatusSectorWeightsOff, radioStatusRxBeamFormingOff, radioStatusPowerDetectorInactive, radioStatusCatQuadCalFail, radioStatusAlarmReason, radioStatusAlarm, atexHazlocPowerLimit, interleave, controlMessages, radioMSN, simulatedAirDelay, latitude, longitude, height, bandwidth, dataScramblingMethod, whispWebUserAccessMode, whispUsrAuth, usrAccountEnableAccounting, allowRejectThenLocal, pppoeFilter, smbFilter, ipv6smbFilter, snmpFilter, ipv6snmpFilter, userP1Filter, userP2Filter, userP3Filter, allOtherIpFilter, allOtherIpv6Filter, allIpv4Filter, allIpv6Filter, arpFilter, allOthersFilter, userDefinedPort1, port1TCPFilter, port1UDPFilter, userDefinedPort2, port2TCPFilter, port2UDPFilter, userDefinedPort3, port3TCPFilter, port3UDPFilter, bootpcFilter, ipv6bootpcFilter, bootpsFilter, ipv6bootpsFilter, ip4MultFilter, ipv6MultFilter, packetFilterDirection, encryptionConfig, activeTxPowerStr, activeTxPowerHdths} STATUS current DESCRIPTION "Canopy Box Level Attributes group." ::= {whispBoxGroups 1} whispBoxControlGroup OBJECT-GROUP OBJECTS { enable8023linkBox, saveFlash, reboot, clearEventLog, rebootIfRequired, clearBERStats, updateDevice, undoUnitWideSavedChanges, resetPoEAux, siteInfoViewable, largeVCQ, snrCalculation, receiveQualityDebug, poeT2Classification, vcDepth, enableSecurityBanner, textSecurityBanner, acceptSecurityBanner, importConfigFile, exportConfigFile} STATUS current DESCRIPTION "Canopy Box Level control group." ::= {whispBoxGroups 2} whispBoxBTGroup OBJECT-GROUP OBJECTS { whispBridgeMacAddr, whispBridgeDesLuid, whispBridgeAge, whispBridgeExt, whispBridgeHash, whispBridgeCAM} STATUS current DESCRIPTION "Canopy Box Bridging Table group." ::= {whispBoxGroups 3} whispBoxVLANTableGroup OBJECT-GROUP OBJECTS { whispVID, whispVType, whispVAge} STATUS current DESCRIPTION "Canopy Box VLAN member Table group." ::= {whispBoxGroups 4} whispBoxCPTableGroup OBJECT-GROUP OBJECTS { codePoint0, codePoint1, codePoint2, codePoint3, codePoint4, codePoint5, codePoint6, codePoint7, codePoint8, codePoint9, codePoint10, codePoint11, codePoint12, codePoint13, codePoint14, codePoint15, codePoint16, codePoint17, codePoint18, codePoint19, codePoint20, codePoint21, codePoint22, codePoint23, codePoint24, codePoint25, codePoint26, codePoint27, codePoint28, codePoint29, codePoint30, codePoint31, codePoint32, codePoint33, codePoint34, codePoint35, codePoint36, codePoint37, codePoint38, codePoint39, codePoint40, codePoint41, codePoint42, codePoint43, codePoint44, codePoint45, codePoint46, codePoint47, codePoint48, codePoint49, codePoint50, codePoint51, codePoint52, codePoint53, codePoint54, codePoint55, codePoint56, codePoint57, codePoint58, codePoint59, codePoint60, codePoint61, codePoint62, codePoint63} STATUS current DESCRIPTION "Code Point Table group." ::= {whispBoxGroups 5} whispBoxUserTableGroup OBJECT-GROUP OBJECTS { entryIndex, userLoginName, userPswd, accessLevel, loginStatus, loginMethod, sessionTime} STATUS current DESCRIPTION "Canopy Box User Information Table group." ::= {whispBoxGroups 6} whispLayer2NeighborTableGroup OBJECT-GROUP OBJECTS { entryL2Index, neighborMAC, neighborIP, neighborSiteName} STATUS current DESCRIPTION "Canopy Box Layer 2 Neighbor information." ::= {whispBoxGroups 7} whispBoxNotifGroup NOTIFICATION-GROUP NOTIFICATIONS { boxLan1DHCPClientEvent, boxPoEType2PowerNotPresent, radioStatusAlarmEvent} STATUS current DESCRIPTION "Canopy Box Notification Group." ::= {whispBoxGroups 8} whispBoxVLANRemarkTableGroup OBJECT-GROUP OBJECTS { sourceVID, remarkVIDState, remarkVID, remarkPriorityState, remarkPriority} STATUS current DESCRIPTION "Canopy Box VLAN Remarking Table group." ::= {whispBoxGroups 9} whispBoxSNMPv3Group OBJECT-GROUP OBJECTS { snmpv3EngineId, snmpv3SecLvl, snmpv3AuthProt, snmpv3PrivProt, roUserName, roAuthPassword, roPrivPassword, rwUserEnable, rwUserName, rwAuthPassword, rwPrivPassword, userName1, user1Enable, user1AuthPassword, user1PrivPassword, userGroup1, userName2, user2Enable, user2AuthPassword, user2PrivPassword, user2Group, userName3, user3Enable, user3AuthPassword, user3PrivPassword, user3Group, snmpv3TrapEnable} STATUS current DESCRIPTION "Canopy Box SNMPv3 Group." ::= {whispBoxGroups 10} whispBoxLinkTestGroup OBJECT-GROUP OBJECTS { linkTestLUIDBox, linkTestDurationBox, linkTestActionBox, linkTestPktLengthBox, linkTestModeBox, linkTestSNRCalculationBox, linkTestWithDualPathBox, linkTestNumPktBox, linkTestForceModulationBox, linkTestDirectionBox, testLUIDBox, linkTestStatusBox, linkTestErrorBox, testDurationBox, downLinkRateBox, upLinkRateBox, downLinkRateExtrapolatedBox, upLinkRateExtrapolatedBox, downLinkEffBox, maxDwnLinkIndexBox, actDwnLinkIndexBox, expDwnFragCountBox, actDwnFragCountBox, upLinkEffBox, expUpFragCountBox, actUpFragCountBox, maxUpLinkIndexBox, actUpLinkIndexBox, fragments1xDwnLinkVerticalBox, fragments2xDwnLinkVerticalBox, fragments3xDwnLinkVerticalBox, fragments4xDwnLinkVerticalBox, fragments1xUpLinkVerticalBox, fragments2xUpLinkVerticalBox, fragments3xUpLinkVerticalBox, fragments4xUpLinkVerticalBox, fragments1xDwnLinkHorizontalBox, fragments2xDwnLinkHorizontalBox, fragments3xDwnLinkHorizontalBox, fragments4xDwnLinkHorizontalBox, fragments1xUpLinkHorizontalBox, fragments2xUpLinkHorizontalBox, fragments3xUpLinkHorizontalBox, fragments4xUpLinkHorizontalBox, bitErrorsCorrected1xDwnLinkVerticalBox, bitErrorsCorrected2xDwnLinkVerticalBox, bitErrorsCorrected3xDwnLinkVerticalBox, bitErrorsCorrected4xDwnLinkVerticalBox, bitErrorsCorrected1xUpLinkVerticalBox, bitErrorsCorrected2xUpLinkVerticalBox, bitErrorsCorrected3xUpLinkVerticalBox, bitErrorsCorrected4xUpLinkVerticalBox, signalToNoiseRatioDownLinkVerticalBox, signalToNoiseRatioUpLinkVerticalBox, bitErrorsCorrected1xDwnLinkHorizontalBox, bitErrorsCorrected2xDwnLinkHorizontalBox, bitErrorsCorrected3xDwnLinkHorizontalBox, bitErrorsCorrected4xDwnLinkHorizontalBox, bitErrorsCorrected1xUpLinkHorizontalBox, bitErrorsCorrected2xUpLinkHorizontalBox, bitErrorsCorrected3xUpLinkHorizontalBox, bitErrorsCorrected4xUpLinkHorizontalBox, signalToNoiseRatioDownLinkHorizontalBox, signalToNoiseRatioUpLinkHorizontalBox, linkTestLastRunTime, linkTestMissedFragDwnLink, linkTestMissedFragUpLink, linkTestNumPktTxActCnt, linkTestNumPktTxExpCnt, linkTestNumPktRxActCnt, linkTestNumPktRxExpCnt, linkTestMVCVC, linkTestMVCPriority, linkTestMVCXmtFragsDL, linkTestMVCRcvFragsDL, linkTestMVCThroughputDL, linkTestMVCEfficiencyDL, linkTestMVCSumimoModRateDL, linkTestMVCSumimoXmtModeDL, linkTestMVCMumimoModRateDL, linkTestMVCMumimoXmtModeDL, linkTestMVCGroupingRatioDL, linkTestMVCXmtFragsTotalDL, linkTestMVCRcvFragsTotalDL, linkTestMVCThroughputTotalDL, linkTestMVCThroughputTotalUntestedVCsDL, linkTestMVCEfficiencyTotalDL, linkTestMVCSlotDistributionDL, linkTestFloodModeBox, linkTestMumimoBox, linkTestVCListBox, linkTestSMRestriction} STATUS current DESCRIPTION "Canopy Box Link Test group." ::= {whispBoxGroups 11} whispBridgeTbUsed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of used entries in bridging table." ::={whispBoxBridgeVar 1} whispBridgeTbFree OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of free entries in bridging table." ::={whispBoxBridgeVar 2} whispBridgeTbErr OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Bridging table errors." ::={whispBoxBridgeVar 3} codePoint0 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Code Point 0." ::={whispBoxCPVar 1} codePoint1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 1." ::={whispBoxCPVar 2} codePoint2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 2." ::={whispBoxCPVar 3} codePoint3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 3." ::={whispBoxCPVar 4} codePoint4 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 4." ::={whispBoxCPVar 5} codePoint5 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 5." ::={whispBoxCPVar 6} codePoint6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 6." ::={whispBoxCPVar 7} codePoint7 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 7." ::={whispBoxCPVar 8} codePoint8 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 8." ::={whispBoxCPVar 9} codePoint9 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 9." ::={whispBoxCPVar 10} codePoint10 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 10." ::={whispBoxCPVar 11} codePoint11 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 11." ::={whispBoxCPVar 12} codePoint12 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 12." ::={whispBoxCPVar 13} codePoint13 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 13." ::={whispBoxCPVar 14} codePoint14 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 14." ::={whispBoxCPVar 15} codePoint15 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 15." ::={whispBoxCPVar 16} codePoint16 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 16." ::={whispBoxCPVar 17} codePoint17 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 17." ::={whispBoxCPVar 18} codePoint18 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 18." ::={whispBoxCPVar 19} codePoint19 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 19." ::={whispBoxCPVar 20} codePoint20 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 20." ::={whispBoxCPVar 21} codePoint21 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 21." ::={whispBoxCPVar 22} codePoint22 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 22." ::={whispBoxCPVar 23} codePoint23 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 23." ::={whispBoxCPVar 24} codePoint24 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 24." ::={whispBoxCPVar 25} codePoint25 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 25." ::={whispBoxCPVar 26} codePoint26 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 26." ::={whispBoxCPVar 27} codePoint27 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 27." ::={whispBoxCPVar 28} codePoint28 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 28." ::={whispBoxCPVar 29} codePoint29 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 29." ::={whispBoxCPVar 30} codePoint30 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 30." ::={whispBoxCPVar 31} codePoint31 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 31." ::={whispBoxCPVar 32} codePoint32 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 32." ::={whispBoxCPVar 33} codePoint33 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 33." ::={whispBoxCPVar 34} codePoint34 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 34." ::={whispBoxCPVar 35} codePoint35 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 35." ::={whispBoxCPVar 36} codePoint36 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 36." ::={whispBoxCPVar 37} codePoint37 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 37." ::={whispBoxCPVar 38} codePoint38 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 38." ::={whispBoxCPVar 39} codePoint39 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 39." ::={whispBoxCPVar 40} codePoint40 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 40." ::={whispBoxCPVar 41} codePoint41 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 41." ::={whispBoxCPVar 42} codePoint42 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 42." ::={whispBoxCPVar 43} codePoint43 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 43." ::={whispBoxCPVar 44} codePoint44 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 44." ::={whispBoxCPVar 45} codePoint45 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 45." ::={whispBoxCPVar 46} codePoint46 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 46." ::={whispBoxCPVar 47} codePoint47 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 47." ::={whispBoxCPVar 48} codePoint48 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Code Point 48." ::={whispBoxCPVar 49} codePoint49 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 49." ::={whispBoxCPVar 50} codePoint50 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 50." ::={whispBoxCPVar 51} codePoint51 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 51." ::={whispBoxCPVar 52} codePoint52 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 52." ::={whispBoxCPVar 53} codePoint53 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 53." ::={whispBoxCPVar 54} codePoint54 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 54." ::={whispBoxCPVar 55} codePoint55 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 55." ::={whispBoxCPVar 56} codePoint56 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Code Point 56." ::={whispBoxCPVar 57} codePoint57 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 57." ::={whispBoxCPVar 58} codePoint58 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 58." ::={whispBoxCPVar 59} codePoint59 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 59." ::={whispBoxCPVar 60} codePoint60 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 60." ::={whispBoxCPVar 61} codePoint61 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 61." ::={whispBoxCPVar 62} codePoint62 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 62." ::={whispBoxCPVar 63} codePoint63 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Code Point 63." ::={whispBoxCPVar 64} -- Lan1 DHCP Client Event on AP or SM (with NAT disabled) boxLan1DHCPClientEvent NOTIFICATION-TYPE OBJECTS { dhcpLanIp, whispBoxEsn} STATUS current DESCRIPTION "Lan1 DHCP Client has received a new address via DHCP" ::={whispBoxDHCPClientEvent 1} -- Transmit disabled due to PoE 802.3at Type 2 not present and not being ignored. boxPoEType2PowerNotPresent NOTIFICATION-TYPE OBJECTS { whispBoxEsn} STATUS current DESCRIPTION "802.3at Type 2 PoE not present, transmit and PoE out disabled" ::={whispBoxPoEEvent 1} -- Radio Status Alarm. radioStatusAlarmEvent NOTIFICATION-TYPE OBJECTS { radioStatusAlarmReason, whispBoxEsn} STATUS current DESCRIPTION "Radio Alarm Event notification." ::={whispBoxRadioAlarmEvent 1} dnsIpState OBJECT-TYPE SYNTAX INTEGER { manual(0), automatic(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration for DNS server IP addresses of the management interface are learned: 0 : Manual, must configure dnsPrimaryMgmtIP and dnsAlternateMgmtIP 1 : Automatic, DNS servers IP addresses are learned from DHCP response of the interface" ::={whispBoxDNS 1} dnsPrimaryMgmtIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Primary DNS IP address for the management interface." ::={whispBoxDNS 2} dnsAlternateMgmtIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Secondary DNS IP address for the management interface." ::={whispBoxDNS 3} dnsMgmtDomainName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Domain Name to use for management DNS configuration. This domain name may be concatonated to DNS names used configured for the management interface." ::={whispBoxDNS 4} trapDomainNameAppend OBJECT-TYPE SYNTAX INTEGER { disableDomain(0), appendDomain(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', trap1 is set to 'trap1', and trapDomainNameAppend is set to appendDomain, the trap1 name used would be 'trap1.example.com'." ::={whispBoxDNS 5} trap1 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 1. Format is either an IP address or DNS name." ::={whispBoxDNS 6} trap2 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 2. Format is either an IP address or DNS name." ::={whispBoxDNS 7} trap3 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 3. Format is either an IP address or DNS name." ::={whispBoxDNS 8} trap4 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 4. Format is either an IP address or DNS name." ::={whispBoxDNS 9} trap5 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 5. Format is either an IP address or DNS name." ::={whispBoxDNS 10} trap6 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 6. Format is either an IP address or DNS name." ::={whispBoxDNS 11} trap7 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 7. Format is either an IP address or DNS name." ::={whispBoxDNS 12} trap8 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 8. Format is either an IP address or DNS name." ::={whispBoxDNS 13} trap9 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 9. Format is either an IP address or DNS name." ::={whispBoxDNS 14} trap10 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "SNMP Trap IP Address 10. Format is either an IP address or DNS name." ::={whispBoxDNS 15} snmpv2cEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable(1) or Disable(0) SNMPv2c access" ::={whispBoxSNMPv3 1} snmpv3EngineId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (10..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The SNMPv3 engine administratively-unique identifier. Length of the identifier should be 5-32 octets which is 10-64 hexadecimal characters and even." ::={whispBoxSNMPv3 2} snmpv3SecLvl OBJECT-TYPE SYNTAX INTEGER { noAuth-noPriv(0), auth-noPriv(1), auth-priv(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "The security level of the SNMPv3 Engine." ::={whispBoxSNMPv3 3} snmpv3AuthProt OBJECT-TYPE SYNTAX INTEGER { md5(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "The SNMPv3 message authentication protocol to use. Currently only MD5 is supported." ::={whispBoxSNMPv3 4} snmpv3PrivProt OBJECT-TYPE SYNTAX INTEGER { cbc-des(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "The SNMPv3 message privacy/encryption protocol to use. Currently only CBC-DES is supported." ::={whispBoxSNMPv3 5} roUserName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Only username." ::={whispBoxSNMPv3 6} roAuthPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Only message authentication password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 7} roPrivPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Only message privacy/encryption password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 8} rwUserEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write User Enable." ::={whispBoxSNMPv3 9} rwUserName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write Username." ::={whispBoxSNMPv3 10} rwAuthPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 11} rwPrivPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 12} snmpv3TrapEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), roUserTrapEnable(1), rwUserTrapEnable(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Trap enable option: (0) Disable - No SNMPv3 Traps Sent (1) Enable Traps to be sent for SNMPv3 Read-Only User (2) Enable Traps to be sent for SNMPv3 Read-Write User NOTE: When disabled SNMPv2c Trap configuration is used." ::={whispBoxSNMPv3 13} user1Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Additional User1 Enable." ::={whispBoxSNMPv3 14} userName1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Additional SNMPv3 Username1." ::={whispBoxSNMPv3 15} user1AuthPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 16} user1PrivPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 17} userGroup1 OBJECT-TYPE SYNTAX INTEGER { readwrite(1), readonly(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User1 Group (ReadWrite/ReadOnly)." ::={whispBoxSNMPv3 18} userName2 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Additional SNMPv3 Username2." ::={whispBoxSNMPv3 19} user2Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Additional User2 Enable." ::={whispBoxSNMPv3 20} user2AuthPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 21} user2PrivPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 22} user2Group OBJECT-TYPE SYNTAX INTEGER { readwrite(1), readonly(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User1 Group (ReadWrite/ReadOnly)." ::={whispBoxSNMPv3 23} userName3 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Additional SNMPv3 Username1." ::={whispBoxSNMPv3 24} user3Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Additional User3 Enable." ::={whispBoxSNMPv3 25} user3AuthPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message authentication password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 26} user3PrivPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Read-Write message privacy/encryption password.Minimum 8 and maximum 32 characters long." ::={whispBoxSNMPv3 27} user3Group OBJECT-TYPE SYNTAX INTEGER { readwrite(1), readonly(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User3 Group (ReadWrite/ReadOnly)." ::={whispBoxSNMPv3 28} whispRegStatusBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS obsolete DESCRIPTION "This shows the registration status of a link." ::={whispBoxLink 4} -- Link test configuration linkTestLUIDBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "LUID selection for Link Test. Valid range: 2-255. Read-Only for SM or Backhaul slave, Read/Write for AP." ::={whispBoxLinkTestConfig 1} linkTestDurationBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Duration for the Link Test. Valid range: 2-10 seconds" ::={whispBoxLinkTestConfig 2} -- Link test action linkTestActionBox OBJECT-TYPE SYNTAX INTEGER { stopped(0), start(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop." ::={whispBoxLinkTestConfig 3} linkTestPktLengthBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Packet length for Link Test. Valid range: 64-1714 bytes" ::={whispBoxLinkTestConfig 4} linkTestModeBox OBJECT-TYPE SYNTAX INTEGER { linktestwithmultipleVCs(4), linktestwithoutbridging(0), linktestwithbridging(1), linktestwithbridgingandmir(2), extrapolatedlinktest(3)} MAX-ACCESS read-write STATUS current DESCRIPTION "Link Test Mode 0 = Link Test without Bridging 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios. 4 = Link Test with Multiple VCs (traffic sent to all registered VCs, or specified VCs) - PMP 450m only" ::={whispBoxLinkTestConfig 5} linkTestSNRCalculationBox OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up." ::={whispBoxLinkTestConfig 6} linkTestWithDualPathBox OBJECT-TYPE SYNTAX INTEGER { lowpriorityvconly(0), highandlowpriorityvcs(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Link Test with: 0 = Low Priority VC only 1 = High and Low Priority VCs" ::={whispBoxLinkTestConfig 7} -- Link test configuration linkTestNumPktBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Number of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test." ::={whispBoxLinkTestConfig 8} linkTestForceModulationBox OBJECT-TYPE SYNTAX INTEGER { normalRateAdapt(0), forceMaxModulation(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Engineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithm" ::={whispBoxLinkTestConfig 9} linkTestDirectionBox OBJECT-TYPE SYNTAX INTEGER { bidirectional(0), uplinkonly(1), downlinkonly(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Link Test Direction - Engineering Use Only 0 = default (will do bidirectional) 1 = Uplink Only 2 = Downlink Only 3 = Bi-Directional (same as 0, setting to 3 will result in setting it to 0)" ::={whispBoxLinkTestConfig 10} linkTestFloodModeBox OBJECT-TYPE SYNTAX INTEGER { external(0), internal(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "PMP 450m only. Engineering use only. Link Test usage: 0 = Packets will be sent out the SM ethernet port 1 = Packets will not be sent out the SM ethernet port" ::={whispBoxLinkTestConfig 11} linkTestMumimoBox OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "PMP 450m only. Link Test usage: 0 = MU-MIMO disabled (legacy or sector mode) 1 = MU-MIMO enabled" ::={whispBoxLinkTestConfig 12} linkTestVCListBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "PMP 450m only. Link Test usage: Enter VCs to be tested (eg. 18 - 22,24,32) Empty field or 0 will flood all registered VCs for duration of test" ::={whispBoxLinkTestConfig 13} linkTestSMRestriction OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0)} MAX-ACCESS read-write STATUS current DESCRIPTION "Control access to SM initiated Link Tests. Disabling will permit all Link Tests initiated at the SM. Enabling will only permit Link Tests that allow user traffic to pass. PMP only." ::={whispBoxLinkTestConfig 14} -- Link test results testLUIDBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "LUID number of selected unit." ::={whispBoxLinkTestResult 1} linkTestStatusBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Status for Link Test." ::={whispBoxLinkTestResult 2} linkTestErrorBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Error status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device." ::={whispBoxLinkTestResult 3} testDurationBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Duration of link test." ::={whispBoxLinkTestResult 4} downLinkRateBox OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Rate." ::={whispBoxLinkTestResult 5} upLinkRateBox OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Uplink Rate." ::={whispBoxLinkTestResult 6} downLinkEffBox OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Down Link Efficiency." ::={whispBoxLinkTestResult 7} maxDwnLinkIndexBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "For link test results, the maximum possible downlink efficiency percentage (always 100%)." ::={whispBoxLinkTestResult 8} actDwnLinkIndexBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Actual down link index." ::={whispBoxLinkTestResult 9} expDwnFragCountBox OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expected Fragment Count." ::={whispBoxLinkTestResult 10} actDwnFragCountBox OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Fragment Count" ::={whispBoxLinkTestResult 11} upLinkEffBox OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Up link efficiency." ::={whispBoxLinkTestResult 12} expUpFragCountBox OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Uplink expected Fragment Count." ::={whispBoxLinkTestResult 13} actUpFragCountBox OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Actual uplink Fragment Count." ::={whispBoxLinkTestResult 14} maxUpLinkIndexBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "For link test results, the maximum possible uplink efficiency percentage (always 100%)." ::={whispBoxLinkTestResult 15} actUpLinkIndexBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Up link index." ::={whispBoxLinkTestResult 16} fragments1xDwnLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 17} fragments2xDwnLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 18} fragments3xDwnLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 19} fragments4xDwnLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 20} fragments1xUpLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 21} fragments2xUpLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 22} fragments3xUpLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 23} fragments4xUpLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 24} bitErrorsCorrected1xDwnLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 25} bitErrorsCorrected2xDwnLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 26} bitErrorsCorrected3xDwnLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 27} bitErrorsCorrected4xDwnLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 28} bitErrorsCorrected1xUpLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 29} bitErrorsCorrected2xUpLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 30} bitErrorsCorrected3xUpLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 31} bitErrorsCorrected4xUpLinkVerticalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 32} signalToNoiseRatioDownLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Estimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 33} signalToNoiseRatioUpLinkVerticalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path." ::={whispBoxLinkTestResult 34} fragments1xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 35} fragments2xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 36} fragments3xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 37} fragments4xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 38} fragments1xUpLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 39} fragments2xUpLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 40} fragments3xUpLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 41} fragments4xUpLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 42} bitErrorsCorrected1xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 43} bitErrorsCorrected2xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 44} bitErrorsCorrected3xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 45} bitErrorsCorrected4xDwnLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 46} bitErrorsCorrected1xUpLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 47} bitErrorsCorrected2xUpLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 48} bitErrorsCorrected3xUpLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Engineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 49} bitErrorsCorrected4xUpLinkHorizontalBox OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical." ::={whispBoxLinkTestResult 50} signalToNoiseRatioDownLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Estimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0." ::={whispBoxLinkTestResult 51} signalToNoiseRatioUpLinkHorizontalBox OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0." ::={whispBoxLinkTestResult 52} downLinkRateExtrapolatedBox OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Extrapolated Downlink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector." ::={whispBoxLinkTestResult 53} upLinkRateExtrapolatedBox OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Extrapolated Uplink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector." ::={whispBoxLinkTestResult 54} linkTestLastRunTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Time and Date when last link test ran." ::={whispBoxLinkTestResult 55} linkTestMissedFragDwnLink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missed fragments during link test in the downlink. Only supported on 450 and 450i." ::={whispBoxLinkTestResult 56} linkTestMissedFragUpLink OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missed fragments during link test in the uplink. Only supported on 450 and 450i." ::={whispBoxLinkTestResult 57} linkTestNumPktTxActCnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of actual packets transmitted during link test." ::={whispBoxLinkTestResult 58} linkTestNumPktTxExpCnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of expected packets to be transmitted during link test." ::={whispBoxLinkTestResult 59} linkTestNumPktRxActCnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of actual packets received during link test." ::={whispBoxLinkTestResult 60} linkTestNumPktRxExpCnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets expected to be received during link test." ::={whispBoxLinkTestResult 61} linkTestMVCXmtFragsTotalDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Total Downlink Fragments Transmitted" ::={whispBoxLinkTestMVCResult 1} linkTestMVCRcvFragsTotalDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Total Downlink Fragments Received" ::={whispBoxLinkTestMVCResult 2} linkTestMVCThroughputTotalDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Total Downlink Throughput for Tested VCs" ::={whispBoxLinkTestMVCResult 3} linkTestMVCThroughputTotalUntestedVCsDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Total Downlink Throughput for Untested VCs. This is the amount of user traffic that was transmitted to VCs during the test that were not part of the Link Test." ::={whispBoxLinkTestMVCResult 4} linkTestMVCEfficiencyTotalDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Total Downlink Efficiency" ::={whispBoxLinkTestMVCResult 5} linkTestMVCSlotDistributionDL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Slot Distribution. Average group size per slot per frame represented as a percentage. 450m only." ::={whispBoxLinkTestMVCResult 6} whispBoxLinkTestMVCTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxLinkTestMVCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Link Test with Multiple VC results." ::= {whispBoxLink 6} whispBoxLinkTestMVCEntry OBJECT-TYPE SYNTAX WhispBoxLinkTestMVCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Link Test with Multiple VC results." INDEX {linkTestMVCVC} ::= {whispBoxLinkTestMVCTable 1} WhispBoxLinkTestMVCEntry ::= SEQUENCE{ linkTestMVCVC INTEGER, linkTestMVCPriority INTEGER, linkTestMVCXmtFragsDL INTEGER, linkTestMVCRcvFragsDL INTEGER, linkTestMVCThroughputDL INTEGER, linkTestMVCEfficiencyDL INTEGER, linkTestMVCSumimoModRateDL INTEGER, linkTestMVCSumimoXmtModeDL INTEGER, linkTestMVCMumimoModRateDL INTEGER, linkTestMVCMumimoXmtModeDL INTEGER, linkTestMVCGroupingRatioDL INTEGER } linkTestMVCVC OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VC" ::={whispBoxLinkTestMVCEntry 1} linkTestMVCPriority OBJECT-TYPE SYNTAX INTEGER { low(0), high(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "VC Priority" ::={whispBoxLinkTestMVCEntry 2} linkTestMVCXmtFragsDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Fragments Transmitted" ::={whispBoxLinkTestMVCEntry 3} linkTestMVCRcvFragsDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Fragments Received" ::={whispBoxLinkTestMVCEntry 4} linkTestMVCThroughputDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Throughput" ::={whispBoxLinkTestMVCEntry 5} linkTestMVCEfficiencyDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Efficiency" ::={whispBoxLinkTestMVCEntry 6} linkTestMVCSumimoModRateDL OBJECT-TYPE SYNTAX INTEGER { noSession(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)} MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink SU-MIMO Modulation Transmit Rate. 0 : No session 1 : 1X QPSK MIMO-A 2 : 2X 16-QAM MIMO-A or QPSK MIMO-B 3 : 3X 64-QAM MIMO-A 4 : 4X 256-QAM MIMO-A or 16-QAM MIMO-B 6 : 6X 64-QAM MIMO-B 8 : 8X 256-QAM MIMO-B" ::={whispBoxLinkTestMVCEntry 7} linkTestMVCSumimoXmtModeDL OBJECT-TYPE SYNTAX INTEGER { mimo-b(0), mimo-a(1), noSession(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink SU-MIMO Transmit Mode. 0 : MIMO-B 1 : MIMO-A 2 : No session" ::={whispBoxLinkTestMVCEntry 8} linkTestMVCMumimoModRateDL OBJECT-TYPE SYNTAX INTEGER { invalid(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)} MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink MU-MIMO Modulation Transmit Rate. 450m only. 0 : Invalid 1 : 1X QPSK MIMO-A 2 : 2X 16-QAM MIMO-A or QPSK MIMO-B 3 : 3X 64-QAM MIMO-A 4 : 4X 256-QAM MIMO-A or 16-QAM MIMO-B 6 : 6X 64-QAM MIMO-B 8 : 8X 256-QAM MIMO-B" ::={whispBoxLinkTestMVCEntry 9} linkTestMVCMumimoXmtModeDL OBJECT-TYPE SYNTAX INTEGER { mimo-b(0), mimo-a(1), invalid(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink MU-MIMO Transmit Mode. 450m only. 0 : MIMO-B 1 : MIMO-A 2 : Invalid" ::={whispBoxLinkTestMVCEntry 10} linkTestMVCGroupingRatioDL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Downlink Grouping Ratio. The percentage of time that a VC is grouped with other VCs to make a MU-MIMO group. 450m only." ::={whispBoxLinkTestMVCEntry 11} certTableUserAuth OBJECT-TYPE SYNTAX SEQUENCE OF CertEntryUserAuth MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CA Certificates for User Auth on radio." ::= {whispUserAuthSecurity 1} certEntryUserAuth OBJECT-TYPE SYNTAX CertEntryUserAuth MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Certifcates." INDEX {certIdx} ::= {certTableUserAuth 1} CertEntryUserAuth ::= SEQUENCE{ certIdx INTEGER, certStatus INTEGER, certAction INTEGER, certDN DisplayString } certIdx OBJECT-TYPE SYNTAX INTEGER (3..4) MAX-ACCESS read-only STATUS current DESCRIPTION "User information table index." ::={certEntryUserAuth 1} certStatus OBJECT-TYPE SYNTAX INTEGER { inactive(0), active(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "0: Inactive 1: Active" ::={certEntryUserAuth 2} certAction OBJECT-TYPE SYNTAX INTEGER { noop(0), delete(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "0: No Operation 1: Delete Certificate" ::={certEntryUserAuth 3} certDN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Distinguished Name of Certificate" ::={certEntryUserAuth 4} whispBoxRFPhysicalRadios OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxRFPhysicalRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio information table." ::= {whispBoxRFPhysical 1} whispBoxRFPhysicalRadioEntry OBJECT-TYPE SYNTAX WhispBoxRFPhysicalRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio information table entry." INDEX {radioIndex} ::= {whispBoxRFPhysicalRadios 1} WhispBoxRFPhysicalRadioEntry ::= SEQUENCE{ radioIndex INTEGER, radioType INTEGER, radioPaths INTEGER } radioIndex OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Radio Index." ::={whispBoxRFPhysicalRadioEntry 1} radioType OBJECT-TYPE SYNTAX INTEGER { fsk(0), ofdm(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the radio is FSK or OFDM." ::={whispBoxRFPhysicalRadioEntry 2} radioPaths OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates number of paths. For FSK or OFDM (non-MIMO), this is 1. For MIMO, it can be greater (with a current maximum of 2)." ::={whispBoxRFPhysicalRadioEntry 3} whispBoxRFPhysicalRadioPaths OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxRFPhysicalRadioPathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio path information table." ::= {whispBoxRFPhysical 2} whispBoxRFPhysicalRadioPathEntry OBJECT-TYPE SYNTAX WhispBoxRFPhysicalRadioPathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio path table entry." INDEX {radioIndex,pathIndex} ::= {whispBoxRFPhysicalRadioPaths 1} WhispBoxRFPhysicalRadioPathEntry ::= SEQUENCE{ pathIndex INTEGER } pathIndex OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Path Index." ::={whispBoxRFPhysicalRadioPathEntry 1} whispBoxRFPhysicalRadioFrequencies OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxRFPhysicalRadioFrequencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Available frequency information table." ::= {whispBoxRFPhysical 3} whispBoxRFPhysicalRadioFrequencyEntry OBJECT-TYPE SYNTAX WhispBoxRFPhysicalRadioFrequencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Available frequency table entry." INDEX {radioIndex,frequency} ::= {whispBoxRFPhysicalRadioFrequencies 1} WhispBoxRFPhysicalRadioFrequencyEntry ::= SEQUENCE{ frequency INTEGER } frequency OBJECT-TYPE SYNTAX INTEGER (0..9000000) MAX-ACCESS read-only STATUS current DESCRIPTION "Frequency." ::={whispBoxRFPhysicalRadioFrequencyEntry 1} whispBoxRFConfigRadios OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxRFConfigRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio configuration table." ::= {whispBoxRFConfig 1} whispBoxRFConfigRadioEntry OBJECT-TYPE SYNTAX WhispBoxRFConfigRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Radio config table entry." INDEX {radioConfigIndex} ::= {whispBoxRFConfigRadios 1} WhispBoxRFConfigRadioEntry ::= SEQUENCE{ radioConfigIndex INTEGER, radioFrequencyBand INTEGER } radioConfigIndex OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Radio Config Index." ::={whispBoxRFConfigRadioEntry 1} radioFrequencyBand OBJECT-TYPE SYNTAX INTEGER { band700(0), band900(1), band2400(2), band3500(3), band3700(4), band4900(5), band5100(6), band5200(7), band5400(8), band5700(9), band5800(10), band5900(11), band6050(12), band3600(13), band4959(14), band3(15)} MAX-ACCESS read-write STATUS current DESCRIPTION "Currently configured radio band. Set is Engineering use only." ::={whispBoxRFConfigRadioEntry 2} whispBoxBridgeTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispBoxBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Bridge table." ::= {whispBox 4} whispBoxBridgeEntry OBJECT-TYPE SYNTAX WhispBoxBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Bridge entry." INDEX {whispBridgeMacAddr} ::= {whispBoxBridgeTable 1} WhispBoxBridgeEntry ::= SEQUENCE{ whispBridgeMacAddr MacAddress, whispBridgeDesLuid WhispLUID, whispBridgeAge INTEGER, whispBridgeExt INTEGER, whispBridgeHash INTEGER, whispBridgeCAM INTEGER } whispBridgeMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC Address of the registered entity." ::={whispBoxBridgeEntry 1} whispBridgeDesLuid OBJECT-TYPE SYNTAX WhispLUID MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Local Unit Identifier assigned to Subscriber Modems." ::={whispBoxBridgeEntry 2} whispBridgeAge OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Table entry last access age in minutes." ::={whispBoxBridgeEntry 3} whispBridgeExt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Timeout extension flag for entries which also reside in the PNA APR cache." ::={whispBoxBridgeEntry 4} whispBridgeHash OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Hash table array index." ::={whispBoxBridgeEntry 5} whispBridgeCAM OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "This entry is deprecated." ::={whispBoxBridgeEntry 6} whispVLANTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispVLANEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN member table." ::= {whispBox 8} whispVLANEntry OBJECT-TYPE SYNTAX WhispVLANEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN entry." INDEX {whispVID} ::= {whispVLANTable 1} WhispVLANEntry ::= SEQUENCE{ whispVID INTEGER, whispVType DisplayString, whispVAge INTEGER } whispVID OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN member ID." ::={whispVLANEntry 1} whispVType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN member type." ::={whispVLANEntry 2} whispVAge OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN member age." ::={whispVLANEntry 3} whispVLANRemarkTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispVLANRemarkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Active VLAN Remarking table." ::= {whispBox 17} whispVLANRemarkEntry OBJECT-TYPE SYNTAX WhispVLANRemarkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Remarking VLAN entry." INDEX {sourceVID} ::= {whispVLANRemarkTable 1} WhispVLANRemarkEntry ::= SEQUENCE{ sourceVID INTEGER, remarkVIDState DisplayString, remarkVID INTEGER, remarkPriorityState DisplayString, remarkPriority INTEGER } sourceVID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Source VLAN ID." ::={whispVLANRemarkEntry 1} remarkVIDState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Remark VID State." ::={whispVLANRemarkEntry 2} remarkVID OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Remark VID." ::={whispVLANRemarkEntry 3} remarkPriorityState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Remark Priority State." ::={whispVLANRemarkEntry 4} remarkPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Remark Priority." ::={whispVLANRemarkEntry 5} whispUserTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User information table." ::= {whispBox 10} whispUserEntry OBJECT-TYPE SYNTAX WhispUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User entry." INDEX {entryIndex} ::= {whispUserTable 1} WhispUserEntry ::= SEQUENCE{ entryIndex INTEGER, userLoginName DisplayString, userPswd DisplayString, accessLevel INTEGER, loginStatus INTEGER, loginMethod INTEGER, sessionTime INTEGER } entryIndex OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-only STATUS current DESCRIPTION "User information table index." ::={whispUserEntry 1} userLoginName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "User name." ::={whispUserEntry 2} userPswd OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "User password." ::={whispUserEntry 3} accessLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "User access level." ::={whispUserEntry 4} loginStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "User current status." ::={whispUserEntry 5} loginMethod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "User login method." ::={whispUserEntry 6} sessionTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Users logged in session time." ::={whispUserEntry 7} whispLayer2NeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF WhispLayer2NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Neighbor information table." ::= {whispBox 11} whispLayer2NeighborEntry OBJECT-TYPE SYNTAX WhispLayer2NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Neighbor Entry." INDEX {entryL2Index} ::= {whispLayer2NeighborTable 1} WhispLayer2NeighborEntry ::= SEQUENCE{ entryL2Index INTEGER, neighborMAC DisplayString, neighborIP DisplayString, neighborSiteName DisplayString } entryL2Index OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "Neighbor information table index." ::={whispLayer2NeighborEntry 1} neighborMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Neighbor MAC." ::={whispLayer2NeighborEntry 2} neighborIP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Neighbor IP." ::={whispLayer2NeighborEntry 3} neighborSiteName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Neighbor Site Name." ::={whispLayer2NeighborEntry 4} END