-- ******************************************************************* -- CISCO-LWAPP-AP-MIB.my -- January 2006, Devesh Pujari, Prasanna Viswakumar, Srinath Candadai -- August 2010, Suja Thangaveluchamy -- Copyright (c) 2006-2007, 2010-2012, 2016-2018 by Cisco Systems, Inc. -- All rights reserved. -- ******************************************************************* CISCO-LWAPP-AP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, Counter32, Counter64, TimeTicks, Gauge32, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF TruthValue, MacAddress, TimeInterval, RowStatus, TimeStamp, DateAndTime FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB PhysicalIndex FROM ENTITY-MIB InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB IANAifType FROM IANAifType-MIB CLApIfType, CLDot11Channel, CLApAssocFailureReason, CLApDot11RadioSubband, CLApDot11RadioRole, CLApMode FROM CISCO-LWAPP-TC-MIB cldRegulatoryDomain FROM CISCO-LWAPP-DOT11-MIB cLWlanIndex FROM CISCO-LWAPP-WLAN-MIB Unsigned64 FROM CISCO-TC cLRFProfileHighDensityMaxRadioClients, cLRFProfileHDClientTrapThreshold FROM CISCO-LWAPP-RF-MIB ciscoMgmt FROM CISCO-SMI; -- ******************************************************************** -- * MODULE IDENTITY -- ******************************************************************** ciscoLwappApMIB MODULE-IDENTITY LAST-UPDATED "201809300000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the 802.11 Access Points that have joined the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Bluetooth Low Energy (BLE) Bluetooth Low Energy is a light-weight subset of classic bluetooth which is added in Hyper Action Location (HALO) enabled APs to make use of BLE beacons to communicate with wireless clients at short range. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Hyper Action Location (HALO) This is an external module for Cisco Access Points, which is responsible for high accuracy indoor location. It includes smart antenna and new software interfaces to enable high accuracy indoor location. iBeacon This is a low-cost transmitter which can transmit its own unique identification number to the local area. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. Link Latency Latency is round trip time between AP and controller. There is a continuous heart-beat between AP and controller. AP calculates latency for each time and sends to controller. AMSDU Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU. DTLS Datagram Transport Layer Security (DTLS) protocol provides communications privacy for datagram protocols. The protocol allows client/server applications to communicate in a way that is designed to prevent eavesdropping, tampering, or message forgery. WIPS Wireless Intrusion Prevention System (WIPS) is a network device that monitors the radio spectrum for the presence of unauthorized access points (intrusion detection), and can automatically take countermeasures (intrusion prevention). SE Spectrum Expert is an application software, which when connected to Spectrum Intelligent Access Point, provides detailed RF spectrum plots and data, and assist in diagnosing network problems. PPPOE Point-to-Point Protocol Over Ethernet provides a standard method to build sessions for transporting multi-protocol datagrams between point-to-point links over Ethernet. OEAP Office Extended Access Point provides a method to extend their office network to outside the office premises like the employee homes, thereby providing a seamless experience to the employee irrespective of the location of the work. This solution should also support having private SSID whose data need to be switched at the AP itself. ME Mobility Express wireless network solution comprises of at least one 802.11ac Wave 2 Cisco Aironet Series access point (AP) with an in-built software-based wireless controller (WLC) managing other APs in the network. The AP acting as the WLC is referred to as the master AP while the other APs in the Cisco Mobility Express network, which are managed by this master AP, are referred to as subordinate APs. In addition to acting as a WLC, the master AP also operates as an AP to serve clients along with the subordinate APs. FIPS Federal Information Processing Standards are a set of standards that describe document processing, encryption algorithms and other information technology standards for use within non-military government agencies and by government contractors and vendors who work with the agencies. LAG Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel. This reduces the number of IP addresses required to configure the ports on your controller. When LAG is enabled, the system dynamically manages port redundancy and load balances access points transparently to the user. CAPWAP The Control And Provisioning of Wireless Access Points (CAPWAP) protocol is a standard, interoperable networking protocol that enables a central wireless LAN Access Controller (AC) to manage a collection of Wireless Termination Points (WTPs), more commonly known as Wireless Access Points. Flexible Radio Assignment The Flexible Radio Assignment feature allows either manual configuration of capable APs or for these APs to intelligently determine the operating role of the integrated radios based on the available RF environment. APs with flexible radio can automatically detect when a high number of devices are connected to a network and changes the dual radios in the access point from 2.4 GHz/5 GHz to 5 GHz/5 GHz to serve more clients. The AP performs this task while monitoring the network for security threats and RF Interference that may affect performance. Flexible Radio Assignment improves mobile user experience for high-density networks. XOR Radio XOR radio is a radio that can operate on both 2.4Ghz and 5Ghz bandwidth. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol." REVISION "201809170000Z" DESCRIPTION "Addition of following new table - cLApProfileTable - cLApProfileHaloBleBeaconTable - cLApPacketCaptureProfileTable - cLApPacketCaptureClientTable - cLApPacketCaptureApTable Added following object to the cLApTable - cLApModeClear - cLApSiteTagName - cLApRfTagName - cLApPolicyTagName - cLApTagSource - cLApUsbModuleName - cLApUsbModuleState - cLApUsbModuleProductId - cLApUsbDescription - cLApUsbStateInfo - cLApUsbOverride - cLApUsbSerialNumber - cLApUsbMaxPower Added following object to the cLApBleBeaconTable - cLApBleBeaconAdvTxPower Added following scalar object - cLApAuthorizeApMacAuth - cLApAuthorizeApSerialNumAuth - cLApAuthorizeApMethodList deprecated the following compliance group - ciscoLwappApMIBComplianceRev7 Added following compliance group - ciscoLwappApMIBComplianceRev8 Added following conformance group - ciscoLwappApProfileHaloBleGroup - ciscoLwappApProfileGroup - ciscoLwappApPacketCaptureProfileGroup - ciscoLwappApPacketCaptureClientProfileGroup." REVISION "201807260000Z" DESCRIPTION "Added following objects to cLApDot11IfTable : - cLApFraSuggestedMode - cLApFraCoverageOverlapFactor." REVISION "201806260000Z" DESCRIPTION "Added enums bleTxRx and bleRxOnly to cLApDot11RadioSubType." REVISION "201803280000Z" DESCRIPTION "Added new object cLApDot11axSupport to the table cLApDot11IfTable. Added new group ciscoLwappApGroupSup11." REVISION "201804240101Z" DESCRIPTION "Added the following objects - cLApGlobal802dot1xSupplicantEapType - cLAp802dot1xSupplicantOverrideEapType" REVISION "201804240000Z" DESCRIPTION "Added the following deprecated objects to ciscoLwappApGroupSup4 : - cLApExtensionChannel - cLAdjChannelRogueEnabled - cLApWipsEnable - cLApNwLegacyBeamForming." REVISION "201707070000Z" DESCRIPTION "Updated the descriptions." REVISION "201705070000Z" DESCRIPTION "Added attribute cLApSecureCipher. Added global attribute cLApGlobalMaxApsSupported." REVISION "201608300000Z" DESCRIPTION "Added following objects to cLApDot11IfTable : - cLApDot11XorRadioMode - cLApDot11XorRadioBand - cLApDot11XorRadioRoleAssignment Added onesixty enum option to cLAp11ChannelBandwidth. Added enums remoteLan and xorTxRx to cLApDot11RadioSubType. Added cLApDot11XorRadioRoleChangeReason, ciscoLwappRadioRoleChangeNotify and ciscoLwappXorRadioRoleChangeEnabled. Added following new groups - ciscoLwappApXorRadioGroup. - ciscoLwappApNotifsXorGroup." REVISION "201604070000Z" DESCRIPTION "Added new object cLApLEDState to the table cLApTable. Addition of new tables cLAplanStatsTable, cLHaloBleBeaconTable and cLApBleBeaconTable." REVISION "201509210000Z" DESCRIPTION "Added new object cLApLEDState to the table cLApTable. Addition of new table cLAplanStatsTable as part of VLAN tagging feature. Added cLApIsUniversal and cLApUniversalPrimeStatus objects to cLApTable." REVISION "201407150000Z" DESCRIPTION "Add new enumeration twentyFiveDotFive(7) to cLApPowerStatus. Added following OBJECT-GROUP - ciscoLwappApGroupSup8 - ciscoLwappApNotifsGroupVer2 - ciscoLwappApGroupSup9 - ciscoLwappApRadioGroupSup1" REVISION "201206130000Z" DESCRIPTION "Added ciscoLwappDot11IfAntennaGroup and ciscoLwappRetransmitGroup" REVISION "201102070000Z" DESCRIPTION "Addressed Approver's comments." REVISION "201101210000Z" DESCRIPTION "Addressed reviwer's comments." REVISION "201101100000Z" DESCRIPTION "Addressed reviewer's comments." REVISION "201012130000Z" DESCRIPTION "Addressed Reviwer's comments" REVISION "201008190000Z" DESCRIPTION "Added cLApGlobal, cLApCredentials, cLSpectrum, cLAp802dot1xSupplicant mib objects. Added link latency tables, cLApEncryptionEnable. cLApDot11RadioTable have been added to provide support for subband radios. AP uptime, join time, join taken time and Ethernet slot info have been added to clApTable. cLApEthernetIfTable which provides Ethernet interface status and statistics information has been added. The group ciscoLwappApGroupSup3, ciscoLwappApGroupSup4, ciscoLwappApNotifObjsGroup and ciscoLwappApNotifsGroup have been added." REVISION "200701030000Z" DESCRIPTION "The object cLApName has been added." REVISION "200607180000Z" DESCRIPTION "Added cLApEntPhysicalIndex object." REVISION "200603300000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 513 } ciscoLwappApMIBNotifs OBJECT IDENTIFIER ::= { ciscoLwappApMIB 0 } ciscoLwappApMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappApMIB 1 } ciscoLwappApMIBConform OBJECT IDENTIFIER ::= { ciscoLwappApMIB 2 } ciscoLwappApMIBNotifObjects OBJECT IDENTIFIER ::= { ciscoLwappApMIB 3 } ciscoLwappAp OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 1 } ciscoLwappApIf OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 2 } ciscoLwappApGlobal OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 3 } ciscoLwappApCredentials OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 4 } ciscoLwappLinkLatency OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 5 } ciscoLwappSpectrum OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 6 } ciscoLwappAp802dot1xSupplicant OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 7 } ciscoLwappApWlanStats OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 9 } ciscoLwappApWlanInfo OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 10 } ciscoLwappPacketDumpInfo OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 11 } ciscoLwappAplanStats OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 12 } ciscoLwappApGlobalBleBeacon OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 13 } ciscoLwappApHyperlocation OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 14 } ciscoLwappApSecureCipher OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 15 } ciscoLwappApProfile OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 16 } ciscoLwappApPacketCapture OBJECT IDENTIFIER ::= { ciscoLwappApMIBObjects 17 } -- ******************************************************************** -- APs that have joined the controller -- ******************************************************************** cLApTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the 802.11 LWAPP Access Points that have joined the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller." ::= { ciscoLwappAp 1 } cLApEntry OBJECT-TYPE SYNTAX CLApEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose their association with the controller due to loss of communication." INDEX { cLApSysMacAddress } ::= { cLApTable 1 } CLApEntry ::= SEQUENCE { cLApSysMacAddress MacAddress, cLApIfMacAddress MacAddress, cLApMaxNumberOfDot11Slots Unsigned32, cLApEntPhysicalIndex PhysicalIndex, cLApName SnmpAdminString, cLApUpTime TimeTicks, cLLwappUpTime TimeTicks, cLLwappJoinTakenTime TimeTicks, cLApMaxNumberOfEthernetSlots Unsigned32, cLApPrimaryControllerAddressType InetAddressType, cLApPrimaryControllerAddress InetAddress, cLApSecondaryControllerAddressType InetAddressType, cLApSecondaryControllerAddress InetAddress, cLApTertiaryControllerAddressType InetAddressType, cLApTertiaryControllerAddress InetAddress, cLApLastRebootReason INTEGER, cLApEncryptionEnable TruthValue, cLApFailoverPriority INTEGER, cLApPowerStatus INTEGER, cLApTelnetEnable TruthValue, cLApSshEnable TruthValue, cLApPreStdStateEnabled TruthValue, cLApPwrInjectorStateEnabled TruthValue, cLApPwrInjectorSelection INTEGER, cLApPwrInjectorSwMacAddr MacAddress, cLApWipsEnable TruthValue, cLApMonitorModeOptimization INTEGER, cLApDomainName SnmpAdminString, cLApNameServerAddressType InetAddressType, cLApNameServerAddress InetAddress, cLApAMSDUEnable TruthValue, cLApEncryptionSupported TruthValue, cLApRogueDetectionEnabled TruthValue, cLApTcpMss Integer32, cLApDataEncryptionStatus TruthValue, cLApNsiKey SnmpAdminString, cLApAdminStatus TruthValue, cLApPortNumber InetPortNumber, cLApRetransmitCount Unsigned32, cLApRetransmitTimeout Unsigned32, cLApVenueConfigVenueGroup INTEGER, cLApVenueConfigVenueType INTEGER, cLApVenueConfigVenueName SnmpAdminString, cLApVenueConfigLanguage SnmpAdminString, cLApLEDState TruthValue, cLApTrunkVlan Unsigned32, cLApTrunkVlanStatus TruthValue, cLApLocation SnmpAdminString, cLApSubMode INTEGER, cLApAssocCount Unsigned32, cLApAssocFailResourceCount Unsigned32, cLApRealTimeStatsModeEnabled TruthValue, cLApAssociatedClientCount Unsigned32, cLApMemoryCurrentUsage Unsigned32, cLApMemoryAverageUsage Unsigned32, cLApCpuCurrentUsage Unsigned32, cLApCpuAverageUsage Unsigned32, cLApUpgradeFromVersion SnmpAdminString, cLApUpgradeToVersion SnmpAdminString, cLApUpgradeFailureCause SnmpAdminString, cLApMaxClientLimitNumberTrap Unsigned32, cLApMaxClientLimitCause SnmpAdminString, cLApMaxClientLimitSet TruthValue, cLApFloorLabel Unsigned64, cLApConnectCount Unsigned32, cLApReassocSuccCount Counter32, cLApReassocFailCount Counter32, cLAdjChannelRogueEnabled TruthValue, cLApAssocFailCountByRate Unsigned32, cLApAbnormalOfflineCount Unsigned32, cLApActiveClientCount Unsigned32, cLApAssocFailCountForRssiLow Unsigned32, cLApSysNetId SnmpAdminString, cLApAssocFailTimes Counter32, cLApAntennaBandMode INTEGER, cLApHeartBeatRspAvgTime Integer32, cLApEchoRequestCount Counter32, cLApEchoResponseLossCount Counter32, cLApModuleInserted SnmpAdminString, cLApEnableModule TruthValue, cLApIsUniversal TruthValue, cLApUniversalPrimeStatus SnmpAdminString, cLApIsMaster TruthValue, cLApBleFWDownloadStatus TruthValue, cLApDot11XorDartConnectorStatus SnmpAdminString, cLApCtsSxpDefaultPassword SnmpAdminString, cLApCtsSxpState TruthValue, cLApCtsSxpMode TruthValue, cLApCtsSxpListenerMinHoldtime Unsigned32, cLApCtsSxpListenerMaxHoldtime Unsigned32, cLApCtsSxpReconcilePeriod Unsigned32, cLApCtsSxpRetryPeriod Unsigned32, cLApCtsSxpSpeakerHoldTime Unsigned32, cLApCtsSxpSpeakerKeepAlive Unsigned32, cLApCtsInlineTagStatus TruthValue, cLApCtsSgaclStatus TruthValue, cLApCtsOverrideStatus TruthValue, cLApModeClear TruthValue, cLApSiteTagName SnmpAdminString, cLApRfTagName SnmpAdminString, cLApPolicyTagName SnmpAdminString, cLApTagSource INTEGER, cLApUsbModuleName SnmpAdminString, cLApUsbModuleState SnmpAdminString, cLApUsbModuleProductId SnmpAdminString, cLApUsbDescription SnmpAdminString, cLApUsbStateInfo TruthValue, cLApUsbOverride TruthValue, cLApUsbSerialNumber SnmpAdminString, cLApUsbMaxPower Unsigned32 } cLApSysMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the radio MAC address common to the dot11 interfaces of the AP and uniquely identifies an entry in this table." ::= { cLApEntry 1 } cLApIfMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Ethernet MAC address of the AP." ::= { cLApEntry 2 } cLApMaxNumberOfDot11Slots OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum number of 802.11 radio interface slots in this AP." ::= { cLApEntry 3 } cLApEntPhysicalIndex OBJECT-TYPE SYNTAX PhysicalIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the index value in the entPhysicalEntry corresponding to this AP." ::= { cLApEntry 4 } cLApName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the administrative name assigned to the AP by the user. If an AP is not configured, its factory default name will be ap: eg. ap:af:12:be." ::= { cLApEntry 5 } cLApUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time in hundredths of a second since the last time the AP rebooted." ::= { cLApEntry 6 } cLLwappUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time in hundredths of a second since the last time the AP joined the controller." ::= { cLApEntry 7 } cLLwappJoinTakenTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time taken in hundredths of a second for the AP to join the controller. This could be a significant value in Mesh environments." ::= { cLApEntry 8 } cLApMaxNumberOfEthernetSlots OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum number of Ethernet slots in this AP." ::= { cLApEntry 9 } cLApPrimaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the primary controller's address made available through cLApPrimaryControllerAddress." ::= { cLApEntry 10 } cLApPrimaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the primary controller that the APs will join." ::= { cLApEntry 11 } cLApSecondaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the secondary controller's address made available through cLApSecondaryControllerAddress." ::= { cLApEntry 12 } cLApSecondaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the secondary controller that the APs will join." ::= { cLApEntry 13 } cLApTertiaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the tertiary controller's address made available through cLApTertiaryControllerAddress." ::= { cLApEntry 14 } cLApTertiaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the tertiary controller that the APs will join." ::= { cLApEntry 15 } cLApLastRebootReason OBJECT-TYPE SYNTAX INTEGER { none(0), dot11gModeChange(1), ipAddressSet(2), ipAddressReset(3), rebootFromController(4), dhcpFallbackFail(5), discoveryFail(6), noJoinResponse(7), denyJoin(8), noConfigResponse(9), configController(10), imageUpgradeSuccess(11), imageOpcodeInvalid(12), imageCheckSumInvalid(13), imageDataTimeout(14), configFileInvalid(15), imageDownloadError(16), rebootFromConsole(17), rapOverAir(18), powerLow(19), crash(20), powerHigh(21), powerLoss(22), powerChange(23), componentFailure(24), watchdog(25), lscEnabled(26), lscDisabled(27), lscProvTimeout(28), lscMaxProvReqRetries(29), lscLoadFailure(30), lscJoinFailure(31), capwapTimerFailure(32), staticIpFailover(33), vlanTagFailover(34), capwapDiscoveryRequest(35), capwapDiscoveryResponse(36), capwapJoinRequest(37), capwapJoinResponse(38), capwapConfigurationStatus(39), capwapConfigurationStatusResponse(40), capwapConfigurationUpdateRequest(41), capwapConfigurationUpdateResponse(42), capwapWtpEventRequest(43), capwapWtpEventResponse(44), capwapChangeStateEventRequest(45), capwapChangeStateEventResponse(46), capwapEchoRequest(47), capwapEchoResponse(48), capwapImageDataRequest(49), capwapImageDataResponse(50), capwapResetRequest(51), capwapResetResponse(52), capwapPrimaryDiscoveryRequest(53), capwapPrimaryDiscoveryResponse(54), capwapDataTransferRequest(55), capwapDataTransferResponse(56), capwapClearConfigurationRequest(57), capwapClearConfigurationResponse(58), capwapMobileConfigurationRequest(59), capwapMobileConfigurationResponse(60), capwapPathMtuRequest(61), capwapPathMtuResponse(62), vlanTagRetry(63), ipv6AddrSet(64), modeChange(65), typeChangedToCapwap(66), typeChangedToMe(67), eraseCfgCommand(68), oeapModeCfgUpload(69), lagCfg(70), fipsModeChange(71), diminishedPowerChange(72), slubDebug(73) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the reason for the last reboot of the AP. none - ap reported a reboot reason code unknown to the controller. dot11gModeChange - 11g mode change ipAddressSet - set static ip address ipAddressReset - reset static ip address rebootFromController - ap reboot initiated from controller dhcpFallbackFail - could not fallback to dhcp discoveryFail - could not send discovery noJoinResponse - did not receive join response denyJoin - deny join attempt at the controller noConfigResponse - did not get config response configController - found configured or master controller imageUpgradeSuccess - image upgraded successfully imageOpcodeInvalid - invalid image data opcode imageCheckSumInvalid - invalid image md5 checksum imageDataTimeout - image data message timeout configFileInvalid - invalid config file imageDownloadError - image download process error rebootFromConsole - reboot command from ap console rapOverAir - root access point is connected over the air brownout - ap rebooted due to power failure powerLow - ap rebooted dued to low power also called as brownout crash - crashed due to software failure powerHigh - rebooted due to power spike powerLoss - rebooted due to power loss powerChange - rebooted due to change in power source componentFailure - rebooted due to component failure watchdog - rebooted due to watch dog timer reset. lscEnabled - rebooted as LSC was enabled lscDisabled - rebooted as LSC was disabled lscProvTimeout - rebooted due to LSC provision timeout lscMaxProvReqRetries - rebooted due to maximum retries of LSC provision request lscLoadFailure - rebooted due to LSC load failure lscJoinFailure - rebooted due to LSC join failure. capwapTimerFailure - rebooted due to capwap timer failure staticIpFailover - rebooted due to static IP failover vlanTagFailover - rebooted due to vlan tag failover capwapDiscoveryRequest - link failure while processing capwap discovery request capwapDiscoveryResponse - link failure while processing capwap discovery response capwapJoinRequest - rebooted due to capwap join request capwapJoinResponse - rebooted due to capwap join response capwapConfigurationStatus- rebooted due to capwap configuration status request capwapConfigurationStatusResponse - rebooted due to capwap configuration status response capwapConfigurationUpdateRequest- rebooted due to capwap configuration update request capwapConfigurationUpdateResponse - rebooted due to capwap configuration update response capwapWtpEventRequest - rebooted due to capwap WTP event request capwapWtpEventResponse - rebooted due to capwap WTP event response capwapChangeStateEventRequest - rebooted due to capwap change state event request capwapChangeStateEventResponse - rebooted due to capwap change state event response capwapEchoRequest - rebooted due to capwap echo request capwapEchoResponse - rebooted due to capwap echo response capwapImageDataRequest - rebooted due to capwap image data request capwapImageDataResponse - rebooted due to capwap image data response capwapResetRequest - rebooted due to capwap reset request capwapResetResponse - rebooted due to capwap reset response capwapPrimaryDiscoveryRequest - rebooted due to capwap primary discovery request capwapPrimaryDiscoveryResponse - rebooted due to capwap primary discovery response capwapDataTransferRequest - rebooted due to capwap data transfer request capwapDataTransferResponse - rebooted due to capwap data transfer response capwapClearConfigurationRequest-rebooted due to capwap clear configuration request capwapClearConfigurationResponse-rebooted due to capwap clear configuration response capwapMobileConfigurationRequest-rebooted due to capwap mobile configuration request capwapMobileConfigurationResponse-rebooted due to capwap mobile configuration response capwapPathMtuRequest - rebooted due to capwap path MTU request capwapPathMtuResponse - rebooted due to capwap path MTU response. vlanTagRetry - rebooted due to vlan tag retry ipv6AddrSet - rebooted due to setting of static ipv6 address modeChange - rebooted due to mode change typeChangedToCapwap - rebooted due to type changed from ME(Mobility Express) to CAPWAP typeChangedToMe - rebooted due to type changed from CAPWAP to ME(Mobility Express) eraseCfgCommand - rebooted due to erase config command oeapModeCfgUpload - rebooted due to OEAP(Office Extended Access Point) mode config upload lagCfg - rebooted due to LAG(Link Aggregate Group) configuration change fipsModeChange - rebooted due to FIPS(Federal Information Processing Standards) mode change diminishedPowerChange - rebooted due to change in diminished power slubDebug - rebooted due to slub debug" ::= { cLApEntry 16 } cLApEncryptionEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether encyrption between controller and AP is enabled or not. Encryption can only be enabled if ESM card in controller is pluged in. A value of 'true' enables encryption between controller and AP. A value of 'false' disables encryption between controller and AP." DEFVAL { false } ::= { cLApEntry 18 } cLApFailoverPriority OBJECT-TYPE SYNTAX INTEGER { low(1), medium(2), high(3), critical(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP failover priority for an AP. If a higher priority AP wishes to join the controller, it will be given preference over a join request from a lower priority AP. Also if the number of AP joined has reached the limit that the controller can support then the controller can disassociate an already joined lower priority AP. This priority will be considered only if the cLApGlobalFailoverPriority is Enabled on the controller. low - AP failover priority is low for this controller. medium - AP failover priority is medium for this controller. high - AP failover priority is high for this controller. critical - AP failover priority is critical for this controller." DEFVAL { low } ::= { cLApEntry 19 } cLApPowerStatus OBJECT-TYPE SYNTAX INTEGER { low(1), fifteendotfour(2), sixteendoteight(3), full(4), external(5), twentyfivedotfive(6), mixedmode(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the power status of the AP low - The AP is drawing low power from Ethernet fifteendotfour - The AP is drawing 15.4 watts from Ethernet sixteendoteight - The AP is drawing 16.8 watts from Ethernet twentyfivedotfive - The AP is drawing 25.5 watts from Ethernet full - The power is high enough for normal operation of the AP. The power source could be Ethernet or external external - The power source is not from Ethernet. mixedmode - The power is high enough for operation of AP. In this state one radio will operate in full power mode while the other radio will be powered off or operate at reduced capacity." ::= { cLApEntry 20 } cLApTelnetEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether telnet session can be established to the AP. A value of 'true' indicates an telnet session can be established to the AP. A value of 'false' indicates an telnet session cannot be established to the AP." DEFVAL { false } ::= { cLApEntry 21 } cLApSshEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether SSH session can be established to the AP. A value of 'true' indicates an SSH session can be established to the AP. A value of 'false' indicates an SSH session cannot be established to the AP." DEFVAL { false } ::= { cLApEntry 22 } cLApPreStdStateEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the pre-standard state of the AP is enabled or disabled. A value of 'true' indicates that the pre-standard state of the AP is enabled, A value of 'false' indicates that the pre-standard state of the AP is disabled" ::= { cLApEntry 23 } cLApPwrInjectorStateEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the power injector state of the AP is enabled or disabled. A value of 'true' indicates that the power injector state of the AP is enabled, A value of 'false' indicates that the power injector state of the AP is disabled" ::= { cLApEntry 24 } cLApPwrInjectorSelection OBJECT-TYPE SYNTAX INTEGER { unknown(1), installed(2), override(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the power injector selection value of the AP. 'unknown' - is returned if 'cLApPwrInjectorStateEnabled'is set to false. 'installed' - configure the MAC address of the switch port that has a Power Injector. 'override' - override the safety checks and assume a power injector is always installed." ::= { cLApEntry 25 } cLApPwrInjectorSwMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the MAC address of the switch port that has a power Injector and is valid only when the 'cLApPwrInjectorSelection' is in 'installed' mode. if SET to 00:00:00:00:00:00, AP will detect the MAC address of the current switch port that has a Power Injector" ::= { cLApEntry 26 } cLApWipsEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents if this AP is used as WIPS AP. A value of 'true' indicates that this AP is a WIPS AP. A value of 'false' indicates that this AP is not a WIPS AP. This applies only when the AP is either in local or monitor mode." DEFVAL { false } ::= { cLApEntry 27 } cLApMonitorModeOptimization OBJECT-TYPE SYNTAX INTEGER { all(1), tracking(2), wips(3), none(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the monitor mode optimization on this device. all - All optimization is enabled tracking - Tracking is optimized wips - WIPS optimization is enabled none - No optimization is enabled" ::= { cLApEntry 28 } cLApDomainName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the domain, to which the AP belongs. This attribute can be configured only if the static IP option is turned on in the AP." ::= { cLApEntry 29 } cLApNameServerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the IP address of the name server, made available through cLApNameServerAddress." ::= { cLApEntry 30 } cLApNameServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the IP Address of the name server. This attribute can be configured only if the static IP option is turned on in the AP." ::= { cLApEntry 31 } cLApAMSDUEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AMSDU status. A value of 'true' indicates AMSDU is enabled. A value of 'false' indicates AMSDU is disabled." DEFVAL { false } ::= { cLApEntry 32 } cLApEncryptionSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether AP Supports DTLS encryption. A value of 'true' indicates encryption is supported. A value of 'false' indicates encryption is not supported." DEFVAL { false } ::= { cLApEntry 33 } cLApRogueDetectionEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether Rogue Detection is enabled in this AP. A value of 'true' indicates rogue detection is enabled. A value of 'false' indicates rogue detection is disabled. Rogue detection is not supported on sniffer and rogue detector mode APs." DEFVAL { false } ::= { cLApEntry 34 } cLApTcpMss OBJECT-TYPE SYNTAX Integer32 (0 | 536..1363) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the TCP Maximum Segment Size for this AP. Permissible value are between 536 and 1363. This will also enable the TCP MSS flag for this AP. Value of 0 will disable the TCP MSS flag for this AP. Any change of value for cLApGlobalTcpMss will be reflected to this object. Value for this object can be change only when value of cLApGlobalTcpMss is set as 0." ::= { cLApEntry 35 } cLApDataEncryptionStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the data encryption status of AP. A value of 'true' indicates data is encrypted between AP and WLC. A value of 'false' indicates data is plain text between AP and WLC." DEFVAL { false } ::= { cLApEntry 36 } cLApNsiKey OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the network spectrum interface key used when the AP is in spectrum expert Only monitor mode (SOMM).This object returns a non-zero value only when the AP is SOMM mode." ::= { cLApEntry 37 } cLApAdminStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the admin state of the AP, A value of 'true' indicates AP admin status is up. A value of 'false' indicates AP admin status is down." DEFVAL { false } ::= { cLApEntry 38 } cLApPortNumber OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the port number on which the AP's traffic is coming through." ::= { cLApEntry 39 } cLApRetransmitCount OBJECT-TYPE SYNTAX Unsigned32 UNITS "retries" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission count for the access point control packet.This value specifies the number of packets retransmitted after which the Access Point falls back to another controller in case of failover. The global retransmit parameters are applicable for all access points within a controller. The individual paramters per access point, if configured takes precedence over the global values. If an access point falls back from another controller(in case of failover), the values at the AP level has more precedence over the global values in the controller with which it has joined." ::= { cLApEntry 40 } cLApRetransmitTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission timeout for the access point control packet. This value specifies the timeout for each retransmission, during the fallback of access point to another controller in case of failover. The global retransmit parameters are applicable for all access points within a controller. The individual paramters per access point, if configured takes precedence over the global values. If an access point falls back from another controller(in case of failover), the values at the AP level has more precedence over the global values in the controller with which it has joined." ::= { cLApEntry 41 } cLApVenueConfigVenueGroup OBJECT-TYPE SYNTAX INTEGER { unspecified(1), assembly(2), business(3), educational(4), factoryAndIndustrial(5), institutional(6), mercantile(7), residential(8), storage(9), utilityAndMisc(10), vehicular(11), outdoor(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the venue group for this WLAN." DEFVAL { unspecified } ::= { cLApEntry 42 } cLApVenueConfigVenueType OBJECT-TYPE SYNTAX INTEGER { unspecified(1), unspecifiedAssembly(2), arena(3), stadium(4), passengerTerminal(5), amphitheater(6), amusementPark(7), placeOfWorship(8), conventionCenter(9), library(10), museum(11), restaurant(12), theater(13), bar(14), coffeeShop(15), zooOrAquarium(16), emergencyCoordinationCenter(17), unspecifiedBusiness(18), doctorOrDentistOffice(19), bank(20), fireStation(21), policeStation(22), postOffice(23), professionalOffice(24), researchAndDevelopmentFacility(25), attorneyOffice(26), unspecifiedEducational(27), schoolPrimary(28), schoolSecondary(29), universityOrCollege(30), unspecifiedFactoryAndIndustrial(31), factory(32), unspecifiedInstitutional(33), hospital(34), longTermCareFacility(35), alcoholAndDrugRehabilitationCenter(36), groupHome(37), prisonOrJail(38), unspecifiedMercantile(39), retailStore(40), groceryMarket(41), atomotiveServiceStation(42), shoppingMall(43), gasStation(44), unspecifiedResidential(45), privateResidence(46), hotelOrMotel(47), dormitory(48), boardingHouse(49), unspecifiedStorage(50), unspecifiedUtility(51), unspecifiedVehicular(52), automobileOrTruck(53), airplane(54), bus(55), ferry(56), shipOrBoat(57), train(58), motorBike(59), unspecifiedOutdoor(60), muniMeshNetwork(61), cityPark(62), restArea(63), trafficControl(64), busStop(65), kiosk(66) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the venue type within a particular venue group,for this WLAN. The venue group-venue type relationship is per the following table: Venue Group Venue Type Code Venue Description =========== =============== ================= 0 0 Unspecified 0 1-255 Reserved 1 0 Unspecified Assembly 1 1 Arena 1 2 Stadium 1 3 Passenger Terminal (e.g., airport, port, bus station, ferry terminal, train station) 1 4 Amphitheater 1 5 Amusement Park 1 6 Place of Worship 1 7 Convention Center 1 8 Library 1 9 Museum 1 10 Restaurant 1 11 Theater 1 12 Bar 1 13 Coffee Shop 1 14 Zoo or Aquarium 1 15 Emergency Coordination Center 1 16-255 Reserved 2 0 Unspecified Business 2 1 Doctor or Dentist office 2 2 Bank 2 3 Fire Station 2 4 Police Station 2 6 Post Office 2 7 Professional Office 2 8 Research and Development Facility 2 9 Attorney Office 2 10-255 Reserved 3 0 Unspecified Educational 3 1 School, Primary 3 2 School, Secondary 3 3 University or College 3 4-255 Reserved 4 0 Unspecified Factory and Industrial 4 1 Factory 4 2-255 Reserved 5 0 Unspecified Institutional 5 1 Hospital 5 2 Long-Term Care Facility (e.g., Nursing home, Hospice, etc.) 5 3 Alcohol and Drug Re-habilitation Center 5 4 Group Home 5 5 Prison or Jail 5 6-255 Reserved 6 0 Unspecified Mercantile 6 1 Retail Store 6 2 Grocery Market 6 3 Automotive Service Station 6 4-255 Reserved 7 0 Unspecified Residential 7 1 Hotel or Motel 7 2 Dormitory 7 3 Boarding House 7 4-255 Reserved 8 0-255 Reserved 9 0-255 Reserved 10 0 Unspecified Vehicular 10 1 Automobile or Truck 10 2 Airplane 10 3 Bus 10 4 Ferry 10 5 Ship or Boat 10 6 Train 10 7-255 Reserved 11 0 Unspecified Outdoor 11 1 Muni-mesh Network 11 2 City Park 11 3-255 Reserved" DEFVAL { unspecified } ::= { cLApEntry 43 } cLApVenueConfigVenueName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the venue name defined for this AP group." ::= { cLApEntry 44 } cLApVenueConfigLanguage OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the language defined for this AP group." ::= { cLApEntry 45 } cLApLEDState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the LED state of this access point should be enabled or disabled. A value of 'true' indicates LED status is enabled. A value of 'false' indicates LED status is disabled." ::= { cLApEntry 46 } cLApTrunkVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the trunk VLAN ID assigned to this AP's ethernet interface. When a non-zero value is assigned for this Object, the management packets will be tagged with this VLAN ID. When the value of trunk VLAN ID is zero, the packets will be untagged" ::= { cLApEntry 47 } cLApTrunkVlanStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies whether the trunk VLAN ID assigned to this AP's is effective. If the AP is unable to route the management frames through the trunk vlan, it will revert back to untagged mode. A value of true indicates that the configured trunk VLAN has taken effect and a value of false indicates that the management packets will be untagged" ::= { cLApEntry 48 } cLApLocation OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the user specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located." ::= { cLApEntry 49 } cLApSubMode OBJECT-TYPE SYNTAX INTEGER { none(1), wips(2), pppoe(3), pppoeWips(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the sub mode of the AP. The option 'wips' applies only when the AP is in local, flexConnect or monitor mode. This 'pppoe' options apply only when the AP is in flexConnect mode." DEFVAL { none } ::= { cLApEntry 50 } cLApAssocCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the association count for the access point. This counter includes both successful and failed associate attempts, but does NOT include the re-associate attempts." ::= { cLApEntry 51 } cLApAssocFailResourceCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the association failure count for the access point due to the resource limits, i.e. the max clients of the WLAN/Radio is reached." ::= { cLApEntry 52 } cLApRealTimeStatsModeEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether current stats mode is 'realtime'. There are two stats-mode, realtime and normal which specifies the stats-timer range to be 10-180 sec and 2-5 sec each. A value of 'true' indicates current mode is realtime. A value of 'false' indicates current mode is not realtime." DEFVAL { false } ::= { cLApEntry 53 } cLApAssociatedClientCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the associated client number for the access point." ::= { cLApEntry 54 } cLApMemoryCurrentUsage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percent of current memory usage of the access point." ::= { cLApEntry 55 } cLApMemoryAverageUsage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percent of average memory usage of the access point. The statistics window is defined by clsSysStatisticsInterval." ::= { cLApEntry 56 } cLApCpuCurrentUsage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percent of current CPU usage of the access point." ::= { cLApEntry 57 } cLApCpuAverageUsage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percent of average CPU usage of the access point. The statistics window is defined by clsSysStatisticsInterval." ::= { cLApEntry 58 } cLApUpgradeFromVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP image upgrade from version." ::= { cLApEntry 59 } cLApUpgradeToVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP image upgrade to version." ::= { cLApEntry 60 } cLApUpgradeFailureCause OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the cause of the AP image upgrade failure." ::= { cLApEntry 61 } cLApMaxClientLimitNumberTrap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the max client limit number." ::= { cLApEntry 62 } cLApMaxClientLimitCause OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the cause of the max client limit reach." ::= { cLApEntry 63 } cLApMaxClientLimitSet OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether this event is raised or cleared. A value of 'true' indicates this event is set. A value of 'false' indicates this even is cleared." ::= { cLApEntry 64 } cLApFloorLabel OBJECT-TYPE SYNTAX Unsigned64 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the floor label for the Access Point." ::= { cLApEntry 65 } cLApConnectCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Count of AP's that are connected to the Controller." ::= { cLApEntry 66 } cLApReassocSuccCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the successful re-association count for the Access Point." ::= { cLApEntry 67 } cLApReassocFailCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the failed re-association count for the Access Point." ::= { cLApEntry 68 } cLAdjChannelRogueEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies if rogue AP detection and removed Traps need to be sent. A value of 'true' indicates adjacent rogue detection is enabled. A value of 'false' indicates adjacent rogue detection is disabled. To Enable this trap it is requested to disable the bsnRogueAPTrapEnable in order to avoid the duplicates." ::= { cLApEntry 69 } cLApAssocFailCountByRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the failed association count for the access point caused by rate mismatch." ::= { cLApEntry 70 } cLApAbnormalOfflineCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the abnormal offline count for the access point." ::= { cLApEntry 71 } cLApActiveClientCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the active client number for the access point." ::= { cLApEntry 72 } cLApAssocFailCountForRssiLow OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the failed association count for the access point caused by RSSI low." ::= { cLApEntry 73 } cLApSysNetId OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the ApSysNetId which is the numeric string to identify the system information like ApName." ::= { cLApEntry 74 } cLApAssocFailTimes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the counts of client failed association to the access point." ::= { cLApEntry 75 } cLApAntennaBandMode OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), single(2), dual(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the mode of antenna band. notApplicable - will return for unsuppported APs. single - configure the AP to use single band for antenna. dual - configure the AP to use both bands for antenna." ::= { cLApEntry 76 } cLApHeartBeatRspAvgTime OBJECT-TYPE SYNTAX Integer32 (1..100000) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the average interval between sending the echo request and receiving the echo response in AP." ::= { cLApEntry 77 } cLApEchoRequestCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the echo request packet count sent from AP to access controller." ::= { cLApEntry 78 } cLApEchoResponseLossCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the echo response loss count from access controller to AP." ::= { cLApEntry 79 } cLApModuleInserted OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the type of the module inserted in to the AP." ::= { cLApEntry 80 } cLApEnableModule OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of the external module . A value of 'true' indicates module is enabled. A value of 'false' indicates module is disabled." ::= { cLApEntry 81 } cLApIsUniversal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the if the AP is universal AP. A value of 'true' indicates AP is universal SKU based AP. A value of 'false' indicates AP is non-Universal SKU AP." ::= { cLApEntry 82 } cLApUniversalPrimeStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the method of Priming of the Universal AP." ::= { cLApEntry 83 } cLApIsMaster OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether the flex AP is a master AP. This applies only to FlexExpress controllers. A value of 'true' indicates AP is a master AP. A value of 'false' indicates AP is not a master AP." ::= { cLApEntry 84 } cLApBleFWDownloadStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the list of APs in which BLE firmware download is in progress. A value of 'true' indicates BLE download is in progress. A value of 'false' indicates BLE download is not in progress." ::= { cLApEntry 85 } cLApDot11XorDartConnectorStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the XOR dart connector status." ::= { cLApEntry 86 } cLApCtsSxpDefaultPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the SXP(Security Group Tag Exchange Protocol) default password." DEFVAL { "" } ::= { cLApEntry 87 } cLApCtsSxpState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) state. A value of 'true' indicates sxp state is enabled. A value of 'false' indicates sxp state is disabled." DEFVAL { false } ::= { cLApEntry 88 } cLApCtsSxpMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) mode. A value of 'true' indicates sxp mode is enabled. A value of 'false' indicates sxp mode is disabled." DEFVAL { false } ::= { cLApEntry 89 } cLApCtsSxpListenerMinHoldtime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) listener hold time. It specifies the global maximum hold-time for SXP connections in 'listener' mode. Value of this object must be lesser than cLApCtsSxpListenerMinHoldTime." DEFVAL { 90 } ::= { cLApEntry 90 } cLApCtsSxpListenerMaxHoldtime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) listener hold time. It specifies the global maximum hold-time for SXP connections in 'listener' mode. Value of this object must be greater than cLApCtsSxpListenerMinHoldTime." DEFVAL { 180 } ::= { cLApEntry 91 } cLApCtsSxpReconcilePeriod OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) reconcile period." DEFVAL { 120 } ::= { cLApEntry 92 } cLApCtsSxpRetryPeriod OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) retry period." DEFVAL { 120 } ::= { cLApEntry 93 } cLApCtsSxpSpeakerHoldTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) speaker hold time." DEFVAL { 120 } ::= { cLApEntry 94 } cLApCtsSxpSpeakerKeepAlive OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies SXP(Security Group Tag Exchange Protocol) speaker keep alive time." DEFVAL { 0 } ::= { cLApEntry 95 } cLApCtsInlineTagStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Cisco Trustsec inline tagging is enabled/disabled. A value 'true' indicates inline tag is enabled. A value 'false' indicates inline tag is disabled." DEFVAL { false } ::= { cLApEntry 96 } cLApCtsSgaclStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Cisco Trustsec Security Group Tag ACL enforcement status. A value 'true' indicates SgACL enforcement is enabled A value 'false' indicates SgACL enforcement is disabled" DEFVAL { false } ::= { cLApEntry 97 } cLApCtsOverrideStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Cisco Trustsec AP Override status. A value of 'true' indicates CTS AP Override is enabled. A value of 'false' indicates CTS AP Override is disabled." DEFVAL { false } ::= { cLApEntry 98 } cLApModeClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to clear the modes like 'Sniffer', 'Monitor' which is not inherited from tag configuration on controller. Once cleared, AP may reboot and move to the AP mode based on current tag configuration. A value of 'true' indicates AP mode is cleared A value of 'false' indicates AP mode is set" ::= { cLApEntry 103 } cLApSiteTagName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the site tag name of the AP" ::= { cLApEntry 104 } cLApRfTagName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the RF tag name of the AP" ::= { cLApEntry 105 } cLApPolicyTagName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the policy tag name of the AP." ::= { cLApEntry 106 } cLApTagSource OBJECT-TYPE SYNTAX INTEGER { none(1), static(2), filterengine(3), pnpserver(4), default(5), location(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the source of the tag." ::= { cLApEntry 107 } cLApUsbModuleName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..66)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies module name of USB module On the AP." ::= { cLApEntry 108 } cLApUsbModuleState OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..66)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies whether USB module detected or not detected on the AP." ::= { cLApEntry 109 } cLApUsbModuleProductId OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..19)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies product Id of USB module on the AP." ::= { cLApEntry 110 } cLApUsbDescription OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..66)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies description of USB module on the AP." ::= { cLApEntry 111 } cLApUsbStateInfo OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies State(enable/disable) of USB module on the AP." ::= { cLApEntry 112 } cLApUsbOverride OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Override(enable/disable) of USB module on the AP." ::= { cLApEntry 113 } cLApUsbSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies serial number of USB module on the AP." ::= { cLApEntry 114 } cLApUsbMaxPower OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies max power given to USB module on the AP." ::= { cLApEntry 115 } -- ******************************************************************** -- * AP Dot11 Interface Information -- ******************************************************************** cLApDot11IfTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters corresponding to the dot11 interfaces of the APs that have joined the controller." ::= { ciscoLwappApIf 1 } cLApDot11IfEntry OBJECT-TYPE SYNTAX CLApDot11IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association." INDEX { cLApSysMacAddress, cLApDot11IfSlotId } ::= { cLApDot11IfTable 1 } CLApDot11IfEntry ::= SEQUENCE { cLApDot11IfSlotId Unsigned32, cLApDot11IfType CLApIfType, cLApDot11IfRegDomain SnmpAdminString, cLApDot11nSupport TruthValue, cLAp11nChannelBandwidth INTEGER, cLApLomEnabled TruthValue, cLApLomFirstChannel CLDot11Channel, cLApLomSecondChannel CLDot11Channel, cLApLomThirdChannel CLDot11Channel, cLApLomFourthChannel CLDot11Channel, cLApExtensionChannel CLDot11Channel, cLApLegacyBeamForming INTEGER, cLApCdpOverAirEnabled TruthValue, cLApDot11IfAdminStatus TruthValue, cLApDot11IfLinkChangeCount Unsigned32, cLApDot11MaxClients Unsigned32, cLApPromiscuousModeDwelling Unsigned32, cLApDot11IfStaKeepingTime TimeTicks, cLApDot11IfLinkSpeed Gauge32, cLApDot11IfMtu Unsigned32, cLApDot11IfDesc SnmpAdminString, cLApDot11acSupport TruthValue, cLAp11ChannelBandwidth INTEGER, cLApExtensionChannels SnmpAdminString, cLAPDot11IfMinTxPowerStep Unsigned32, cLApDot11XorRadioMode INTEGER, cLApDot11XorRadioBand INTEGER, cLApDot11XorRadioRoleAssignment INTEGER, cLApDot11IfMaxDataRate Unsigned32, cLApDot11IfSensorReachability Unsigned32, cLApDot11axSupport TruthValue, cLApFraCoverageOverlapFactor Integer32, cLApFraSuggestedMode INTEGER } cLApDot11IfSlotId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the slot ID of a dot11 interface on an AP. The slot ID for a particular dot11 interface as represented by this object ranges from 0 to cLApMaxNumberOfDot11Slots - 1." ::= { cLApDot11IfEntry 1 } cLApDot11IfType OBJECT-TYPE SYNTAX CLApIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the type of this dot11 interface." ::= { cLApDot11IfEntry 2 } cLApDot11IfRegDomain OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the regulatory domain for this radio type on this AP." ::= { cLApDot11IfEntry 3 } cLApDot11nSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents whether 11n support is enabled on this radio. A value of 'true' indicates 11n support is enabled. A value of 'false' indicates 11n support is disabled." ::= { cLApDot11IfEntry 4 } cLAp11nChannelBandwidth OBJECT-TYPE SYNTAX INTEGER { five(1), ten(2), twenty(3), forty(4) } UNITS "mhz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the channel bandwidth for this AP. This applies to 802.11n networks only. This has been deprecated for cLAp11ChannelBandwidth." ::= { cLApDot11IfEntry 5 } cLApLomEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object indicates whether this AP is being monitored by the location server. A value of 'true' indicates that the monitoring is enabled. A value of 'false' indicates that the monitoring is disabled." DEFVAL { false } ::= { cLApDot11IfEntry 6 } cLApLomFirstChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the first location channel that is being monitored." ::= { cLApDot11IfEntry 7 } cLApLomSecondChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the second location channel that is being monitored." ::= { cLApDot11IfEntry 8 } cLApLomThirdChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the third location channel that is being monitored." ::= { cLApDot11IfEntry 9 } cLApLomFourthChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the fourth location channel that is being monitored." ::= { cLApDot11IfEntry 10 } cLApExtensionChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object specifies the extension channel. This is applicable when the channel bandwidth is set to 40mhz." ::= { cLApDot11IfEntry 11 } cLApLegacyBeamForming OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notApplicable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of legacy beam forming in this AP. This object is applicable only for 11n supported APs. For APs that does not support legacy beam forming, a get request on this attribute will return the value 'notApplicable'. A value of 'enable' indicates that the legacy Beam forming is enabled in this AP. A value of 'false' indicates that the legacy Beam forming is disabled in this AP." DEFVAL { notApplicable } ::= { cLApDot11IfEntry 12 } cLApCdpOverAirEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of Cisco Discovery Protocol(CDP) in this interface, represented by cLApDot11IfSlotId of the AP, represented by cLApSysMacAddress. A value of 'true' indicates that CDP is enabled in the dot11 interface(s) of this AP. A value of 'false' indicates that CDP is disabled in the dot11 interface(s) of this AP." ::= { cLApDot11IfEntry 13 } cLApDot11IfAdminStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP's interface admin status. A value of 'true' indicates admin state is up. A value of 'false' indicates admin state is down." ::= { cLApDot11IfEntry 14 } cLApDot11IfLinkChangeCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the link change count of a dot11 interface on an AP." ::= { cLApDot11IfEntry 15 } cLApDot11MaxClients OBJECT-TYPE SYNTAX Unsigned32 (1..200) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the max supported associated clients of a dot11 interface on an AP." DEFVAL { 200 } ::= { cLApDot11IfEntry 16 } cLApPromiscuousModeDwelling OBJECT-TYPE SYNTAX Unsigned32 UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percentage of time for the dot11 interface of an Access Point spent in promiscuous mode dwelling." ::= { cLApDot11IfEntry 17 } cLApDot11IfStaKeepingTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time in hundredths of a second since the last dot11 interface state changed." ::= { cLApDot11IfEntry 18 } cLApDot11IfLinkSpeed OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the speed of the interface in units of 1,000,000 bits per second." ::= { cLApDot11IfEntry 19 } cLApDot11IfMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents interface's MTU value." ::= { cLApDot11IfEntry 20 } cLApDot11IfDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the description of this interface." ::= { cLApDot11IfEntry 21 } cLApDot11acSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents whether 802.11ac support is enabled on this AP. A value of 'true' indicates 11ac support for slot is enabled. A value of 'false' indicates 11ac support for slot is disabled." ::= { cLApDot11IfEntry 22 } cLAp11ChannelBandwidth OBJECT-TYPE SYNTAX INTEGER { five(1), ten(2), twenty(3), fourty(4), eighty(5), onesixty(6) } UNITS "mhz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the channel bandwidth for this AP. This applies to 802.11n and 802.11ac networks only." ::= { cLApDot11IfEntry 23 } cLApExtensionChannels OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the extension channels separated by commas. This is applicable when the channel bandwidth is set to 40mhz or 80mhz." ::= { cLApDot11IfEntry 24 } cLAPDot11IfMinTxPowerStep OBJECT-TYPE SYNTAX Unsigned32 UNITS "dbm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents minimum adjust step of the AP radio TX power. The power step is coded as an unsigned integer in units of dbm." ::= { cLApDot11IfEntry 25 } cLApDot11XorRadioMode OBJECT-TYPE SYNTAX INTEGER { servingClients(1), monitor(2), sensor(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the radio mode for the AP which has XOR radio. servingClients - xor radio is configured to serve the clients (local/flexconnect/bridge). monitor -xor radio is configured to operate in monitor mode. sensor - xor radio is configured to operate in sensor mode." ::= { cLApDot11IfEntry 26 } cLApDot11XorRadioBand OBJECT-TYPE SYNTAX INTEGER { radioband24G(1), radioband5G(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the operating band of XOR radio. radioband24G - operating band for xor radio is 2.4GHz. radioband5G - operating band for xor radio is 5GHz." ::= { cLApDot11IfEntry 27 } cLApDot11XorRadioRoleAssignment OBJECT-TYPE SYNTAX INTEGER { auto(1), manual(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the radio role assignment of XOR radio. auto - xor radio configured to change band/mode automatically. manual - xor radio's band/mode can be configured manually." ::= { cLApDot11IfEntry 28 } cLApDot11IfMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum data rate of a dot11 interface on an AP in Mbps." ::= { cLApDot11IfEntry 29 } cLApDot11IfSensorReachability OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents sensor radio's ability to cover localized RF neighbors.It represents value in percentage which shows percentage of neighbors covered by this sensor." ::= { cLApDot11IfEntry 30 } cLApDot11axSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This objects represents whether 802.11ax support is enabled on this AP. A value of 'true' indicates 11ax support for slot is enabled. A value of 'false' indicates 11ax support for slot is disabled." ::= { cLApDot11IfEntry 31 } cLApFraCoverageOverlapFactor OBJECT-TYPE SYNTAX Integer32 UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the COF(Coverage Overlap Factor) in percentage.COF represents overlap on a given radio's transmit cell size by its adjacent neighbors.When COF value is higher than FRA(Flexible Radio Assignment) sensitivity, given radio will be most likely marked as redundant by FRA algorithm." ::= { cLApDot11IfEntry 32 } cLApFraSuggestedMode OBJECT-TYPE SYNTAX INTEGER { static(1), none(2), radioBand5GMonitor(3), radioBand24G(4), notApplicable(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the band/mode XOR radio can move to, for better performance. static - XOR radio's band/mode is in manual assignment. none - FRA(Flexible Radio Assignment) algorithm is disabled. radioBand5GMonitor - FRA suggested mode/band is 5GHz or Monitor role. radioBand24G - XOR radio is not redundant. notApplicable - Radio is not XOR." ::= { cLApDot11IfEntry 33 } -- ******************************************************************** -- * AP Ethernet Interface Information -- ******************************************************************** cLApEthernetIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApEthernetIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters corresponding to the Ethernet interfaces of the APs that have joined the controller." ::= { ciscoLwappApIf 2 } cLApEthernetIfEntry OBJECT-TYPE SYNTAX CLApEthernetIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association." INDEX { cLApSysMacAddress, cLApEthernetIfSlotId } ::= { cLApEthernetIfTable 1 } CLApEthernetIfEntry ::= SEQUENCE { cLApEthernetIfSlotId Unsigned32, cLApEthernetIfName SnmpAdminString, cLApEthernetIfMacAddress MacAddress, cLApEthernetIfAdminStatus INTEGER, cLApEthernetIfOperStatus INTEGER, cLApEthernetIfRxUcastPkts Counter32, cLApEthernetIfRxNUcastPkts Counter32, cLApEthernetIfTxUcastPkts Counter32, cLApEthernetIfTxNUcastPkts Counter32, cLApEthernetIfDuplex INTEGER, cLApEthernetIfLinkSpeed Gauge32, cLApEthernetIfPOEPower INTEGER, cLApEthernetIfRxTotalBytes Counter32, cLApEthernetIfTxTotalBytes Counter32, cLApEthernetIfInputCrc Counter32, cLApEthernetIfInputAborts Counter32, cLApEthernetIfInputErrors Counter32, cLApEthernetIfInputFrames Counter32, cLApEthernetIfInputOverrun Counter32, cLApEthernetIfInputDrops Counter32, cLApEthernetIfInputResource Counter32, cLApEthernetIfUnknownProtocol Counter32, cLApEthernetIfRunts Counter32, cLApEthernetIfGiants Counter32, cLApEthernetIfThrottle Counter32, cLApEthernetIfResets Counter32, cLApEthernetIfOutputCollision Counter32, cLApEthernetIfOutputNoBuffer Counter32, cLApEthernetIfOutputResource Counter32, cLApEthernetIfOutputUnderrun Counter32, cLApEthernetIfOutputErrors Counter32, cLApEthernetIfOutputTotalDrops Counter32, cLApEthernetIfCdpEnabled TruthValue, cLApEthernetIfMtu Unsigned32, cLApEthernetIfType IANAifType, cLApEthernetIfLinkChangeCount Counter32 } cLApEthernetIfSlotId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the slot ID of an Ethernet interface on an AP. The slot ID for a particular Ethernet interface as represented by this object ranges from 0 to cLApMaxNumberOfEthernetSlots - 1." ::= { cLApEthernetIfEntry 1 } cLApEthernetIfName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the ethernet interface." ::= { cLApEthernetIfEntry 2 } cLApEthernetIfMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents MAC address of the ethernet interface in the slot represented by cLApEthernetIfSlotId." ::= { cLApEthernetIfEntry 3 } cLApEthernetIfAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the admin state of the physical ethernet interface on the AP. up - Admin state of ethernet interface is up. down - Admin state of ethernet interface is down." ::= { cLApEthernetIfEntry 4 } cLApEthernetIfOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the operational state of the physical Ethernet interface on the AP. up - Operational state of ethernet interface is up. down - Operational state of ethernet interface is down." ::= { cLApEthernetIfEntry 5 } cLApEthernetIfRxUcastPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of unicast packets received on the interface." ::= { cLApEthernetIfEntry 6 } cLApEthernetIfRxNUcastPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of non-unicast or multicast packets received on the interface" ::= { cLApEthernetIfEntry 7 } cLApEthernetIfTxUcastPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of unicast packets transmitted on the interface." ::= { cLApEthernetIfEntry 8 } cLApEthernetIfTxNUcastPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of non-unicast or multicast packets transmitted on the interface" ::= { cLApEthernetIfEntry 9 } cLApEthernetIfDuplex OBJECT-TYPE SYNTAX INTEGER { unknown(1), halfduplex(2), fullduplex(3), auto(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the interface's duplex mode" ::= { cLApEthernetIfEntry 10 } cLApEthernetIfLinkSpeed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the speed of the interface in units of 1,000,000 bits per second" ::= { cLApEthernetIfEntry 11 } cLApEthernetIfPOEPower OBJECT-TYPE SYNTAX INTEGER { none(1), drawn(2), notdrawn(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether this interface supports Power Over Ethernet (POE) none - POE is not supported drawn - This interface supports POE, and power is being drawn notdrawn - POE power is not drawn" ::= { cLApEthernetIfEntry 12 } cLApEthernetIfRxTotalBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of bytes in the error-free packets received on the interface." ::= { cLApEthernetIfEntry 13 } cLApEthernetIfTxTotalBytes OBJECT-TYPE SYNTAX Counter32 UNITS "Bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of bytes in the error-free packets transmitted on the interface." ::= { cLApEthernetIfEntry 14 } cLApEthernetIfInputCrc OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of CRC error in packets received on the interface." ::= { cLApEthernetIfEntry 15 } cLApEthernetIfInputAborts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packet aborted while receiving on the interface." ::= { cLApEthernetIfEntry 16 } cLApEthernetIfInputErrors OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the sum of all errors in the packets while receiving on the interface." ::= { cLApEthernetIfEntry 17 } cLApEthernetIfInputFrames OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packet received incorrectly having a CRC error and a noninteger number of octets on the interface." ::= { cLApEthernetIfEntry 18 } cLApEthernetIfInputOverrun OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of times the receiver hardware was incapable of handing received data to a hardware buffer because the input rate exceeded the receiver's capability to handle the data." ::= { cLApEthernetIfEntry 19 } cLApEthernetIfInputDrops OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packets dropped while receiving on the interface because the queue was full." ::= { cLApEthernetIfEntry 20 } cLApEthernetIfInputResource OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of resource errors in packets received on the interface." ::= { cLApEthernetIfEntry 21 } cLApEthernetIfUnknownProtocol OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packet discarded on the interface due to unknown protocol." ::= { cLApEthernetIfEntry 22 } cLApEthernetIfRunts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of packets that are discarded because they are smaller than the medium's minimum packet size." ::= { cLApEthernetIfEntry 23 } cLApEthernetIfGiants OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of packets that are discarded because they exceed the medium's maximum packet size." ::= { cLApEthernetIfEntry 24 } cLApEthernetIfThrottle OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of times the interface advised a sending NIC that it was overwhelmed by packets being sent and to slow the pace of delivery." ::= { cLApEthernetIfEntry 25 } cLApEthernetIfResets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents number of times that an interface has been completely reset." ::= { cLApEthernetIfEntry 26 } cLApEthernetIfOutputCollision OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packet retransmitted due to an Ethernet collision." ::= { cLApEthernetIfEntry 27 } cLApEthernetIfOutputNoBuffer OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packets discarded because there was no buffer space." ::= { cLApEthernetIfEntry 28 } cLApEthernetIfOutputResource OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of resource errors in packets transmitted on the interface." ::= { cLApEthernetIfEntry 29 } cLApEthernetIfOutputUnderrun OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of times the transmitter has been running faster than the router can handle." ::= { cLApEthernetIfEntry 30 } cLApEthernetIfOutputErrors OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents sum of all errors that prevented the final transmission of packets out of the interface." ::= { cLApEthernetIfEntry 31 } cLApEthernetIfOutputTotalDrops OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of packets dropped while transmitting from the interface because the queue was full." ::= { cLApEthernetIfEntry 32 } cLApEthernetIfCdpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of Cisco Discovery Protocol(CDP) in this interface represented by cLApEthernetIfSlotId of the AP represented by cLApSysMacAddress. A value of 'true' indicates that CDP is enabled in this interface. A value of 'false' indicates that CDP is disabled in this interface." DEFVAL { true } ::= { cLApEthernetIfEntry 33 } cLApEthernetIfMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents interface's MTU value" ::= { cLApEthernetIfEntry 34 } cLApEthernetIfType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention." ::= { cLApEthernetIfEntry 35 } cLApEthernetIfLinkChangeCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the link change count of ethernet interface on the AP." ::= { cLApEthernetIfEntry 36 } -- ******************************************************************** -- * AP Dot11 radio Information -- ******************************************************************** cLApDot11RadioTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11RadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters of the radios of the APs that have joined the controller." ::= { ciscoLwappApIf 3 } cLApDot11RadioEntry OBJECT-TYPE SYNTAX CLApDot11RadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the 802.11 functional parameters of the radio of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association." INDEX { cLApSysMacAddress, cLApDot11IfSlotId } ::= { cLApDot11RadioTable 1 } CLApDot11RadioEntry ::= SEQUENCE { cLApDot11RadioMACAddress MacAddress, cLApDot11RadioSubBand CLApDot11RadioSubband, cLApDot11RadioVersion SnmpAdminString, cLApDot11IsBackhaul TruthValue, cLApDot11RadioRole CLApDot11RadioRole, cLApDot11RadioMode INTEGER, cLApDot11RadioSubType INTEGER } cLApDot11RadioMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the base Mac address of the radio." ::= { cLApDot11RadioEntry 1 } cLApDot11RadioSubBand OBJECT-TYPE SYNTAX CLApDot11RadioSubband MAX-ACCESS read-only STATUS current DESCRIPTION "This object reprsents the sub band on which this radio operates." ::= { cLApDot11RadioEntry 2 } cLApDot11RadioVersion OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..50)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the firmware version of the radio." ::= { cLApDot11RadioEntry 3 } cLApDot11IsBackhaul OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether this interface is backhaul radio or not. A value of 'true' indicates backhaul access for radio is enabled. A value of 'false' indicates backhaul access for radio is disabled." ::= { cLApDot11RadioEntry 4 } cLApDot11RadioRole OBJECT-TYPE SYNTAX CLApDot11RadioRole MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the role of the radio." ::= { cLApDot11RadioEntry 5 } cLApDot11RadioMode OBJECT-TYPE SYNTAX INTEGER { local(1), monitor(2), remote(3), rogueDetector(4), sniffer(5), bridge(6), seConnect(7), hybridRemote(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the mode of the radio. local(1) : The default option. Serving WLAN clients and scanning channels for threats. monitor(2) : A monitor mode. AP spends all of its cycles scanning channels and looking for rogues. remote(3) : This mode indicates that AP is a remote edge lightweight access point. rogueDetector(4) : This mode monitors the rogue APs on wire. It does not transmit or receive frames over the air or contain rogue APs. sniffer(5) : The access point starts sniffing the air on a given channel. bridge(6) : This mode indicates that a root AP is connected. seConnect(7) : AP is connected to spectrum expert. The AP is able to perform spectrum intelligence. hybridRemote(8) : A mode for branch office and remote office deployment." ::= { cLApDot11RadioEntry 6 } cLApDot11RadioSubType OBJECT-TYPE SYNTAX INTEGER { main(1), rxOnly(2), slaveAc(3), remoteLan(4), xorTxRx(5), bleTxRx(6), bleRxOnly(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the subtype of the radio. main(1) :radio operates normally. rxOnly(2) :NOS radio type,which is explicitely used for monitor mode operation. slaveAc(3) :x-ale radio type is only for local mode. remoteLan(4) :Remote-LAN supported Slot. xorTxRx(5) :Xor radio capable of both TX and RX. bleTxRx(6) :radio operating normally and BLE is enabled for the AP. bleRxOnly(7) :radio is explicitly used for monitor mode operation and BLE is enabled for the AP." ::= { cLApDot11RadioEntry 7 } -- ******************************************************************** -- * Global AP Credentials -- ******************************************************************** cLApCredentialGlobalUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the global username for all the APs already joined or will join the controller. This user name is used to access the console on the AP." ::= { ciscoLwappApCredentials 1 } cLApCredentialGlobalPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the password corresponding to the user name represented by cLApCredentialGlobalUserName object." ::= { ciscoLwappApCredentials 2 } cLApCredentialGlobalSecret OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the secret key for all the APs already joined or will join the controller. This provides read-write access to the console on the AP." ::= { ciscoLwappApCredentials 3 } -- ******************************************************************** -- * Per AP Credentials -- ******************************************************************** cLApCredentialsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApCredentialsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the information about the credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added to this table whenever, new APs are joined to this controller, and rows are deleted whenever APs gets disjoined from the controller." ::= { ciscoLwappApCredentials 4 } cLApCredentialsEntry OBJECT-TYPE SYNTAX CLApCredentialsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. cLApSysMacAddress is the index which uniquely identifies every row in the table." INDEX { cLApSysMacAddress } ::= { cLApCredentialsTable 1 } CLApCredentialsEntry ::= SEQUENCE { cLApCredentialUserName SnmpAdminString, cLApCredentialPassword SnmpAdminString, cLApCredentialSecret SnmpAdminString, cLApCredentialEnableGlobalCredentials TruthValue } cLApCredentialUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the username for this AP." ::= { cLApCredentialsEntry 1 } cLApCredentialPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the password corresponding to user name represented by cLApCredentialUserName object." ::= { cLApCredentialsEntry 2 } cLApCredentialSecret OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the secret key for the specific AP. This provides the read-write access on the console for this AP." ::= { cLApCredentialsEntry 3 } cLApCredentialEnableGlobalCredentials OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether the global credentials for the AP is enabled or disabled. A value of 'true' indicates the global username/password to be used for this AP . A value of 'false' indicates the global credentials and uses the credentials specific for this AP is disabled." ::= { cLApCredentialsEntry 4 } -- ******************************************************************** -- * Link Latency parameters -- ******************************************************************** cLApLinkLatencyTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApLinkLatencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the link latency configuration for each AP. An entry is automatically added to this table when an Access Points Joins controller. Entry is removed from this table when AP disassociates from the controllers." ::= { ciscoLwappLinkLatency 1 } cLApLinkLatencyEntry OBJECT-TYPE SYNTAX CLApLinkLatencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides configuration related to Link latency on each AP." INDEX { cLApSysMacAddress } ::= { cLApLinkLatencyTable 1 } CLApLinkLatencyEntry ::= SEQUENCE { cLApLinkLatencyEnable TruthValue, cLApLinkLatencyReset TruthValue } cLApLinkLatencyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to configure the Link Latency on the AP. A value of 'true' indicates that the Link Latency is enabled. A value of 'false' indicates that the Link Latency is disabled." DEFVAL { false } ::= { cLApLinkLatencyEntry 1 } cLApLinkLatencyReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to reset the Link Latency stored at controller for an AP. A value of 'true' indicates that the Link Latency stats is to be reset. A value of 'false' on this during set will return error. A value of false will be returned on get." DEFVAL { false } ::= { cLApLinkLatencyEntry 2 } -- ******************************************************************** -- * Link Latency Stats -- ******************************************************************** cLApLinkLatencyStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApLinkLatencyStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the link latency statistics calculated for each AP. An entry is automatically added by the controller when a 'cLApLinkLatencyEnable' is enabled on an Access Point. Entry is deleted when 'cLApLinkLatencyEnable' is disabled on the Access Point." ::= { ciscoLwappLinkLatency 2 } cLApLinkLatencyStatsEntry OBJECT-TYPE SYNTAX CLApLinkLatencyStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides minimum, maximum and average Link latency for a Access Point. Entries are removed when the Link Latency is disabled on a Access Point." INDEX { cLApSysMacAddress } ::= { cLApLinkLatencyStatsTable 1 } CLApLinkLatencyStatsEntry ::= SEQUENCE { cLApLinkLatencyStatsCurrent TimeInterval, cLApLinkLatencyStatsMin TimeInterval, cLApLinkLatencyStatsMax TimeInterval, cLApLinkLatencyTimeStamp TimeStamp, cLApDataLinkLatencyStatsCurrent TimeInterval, cLApDataLinkLatencyStatsMin TimeInterval, cLApDataLinkLatencyStatsMax TimeInterval, cLApDataLinkLatencyTimeStamp TimeStamp } cLApLinkLatencyStatsCurrent OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the current Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 1 } cLApLinkLatencyStatsMin OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the minimum Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 2 } cLApLinkLatencyStatsMax OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 3 } cLApLinkLatencyTimeStamp OBJECT-TYPE SYNTAX TimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'." ::= { cLApLinkLatencyStatsEntry 4 } cLApDataLinkLatencyStatsCurrent OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the current Data Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 5 } cLApDataLinkLatencyStatsMin OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the minimum Data Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 6 } cLApDataLinkLatencyStatsMax OBJECT-TYPE SYNTAX TimeInterval UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum Data Link latency recorded for this Access point." ::= { cLApLinkLatencyStatsEntry 7 } cLApDataLinkLatencyTimeStamp OBJECT-TYPE SYNTAX TimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'." ::= { cLApLinkLatencyStatsEntry 8 } -- ******************************************************************** -- * AP LAN Stats. -- ******************************************************************** cLAplanStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAplanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Saridinia AP LAN stats information that have joined the controller." ::= { ciscoLwappAplanStats 1 } cLAplanStatsEntry OBJECT-TYPE SYNTAX CLAplanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of LAN stats" INDEX { cLApSysMacAddress, cLApLanPortId } ::= { cLAplanStatsTable 1 } CLAplanStatsEntry ::= SEQUENCE { cLApLanPortId Integer32, cLApLanPortState TruthValue, cLApLanPortVlanId Unsigned32, cLApLanPortVlanIdValid TruthValue, cLApLanPoeState TruthValue } cLApLanPortId OBJECT-TYPE SYNTAX Integer32 (1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the ID of a LAN port of an AP." ::= { cLAplanStatsEntry 1 } cLApLanPortState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of an ethernet interface of AP. A value of 'true' indicates admin status of ethernet interface is up. A value of 'false' indicates admin status of ethernet interface is down." DEFVAL { false } ::= { cLAplanStatsEntry 2 } cLApLanPortVlanId OBJECT-TYPE SYNTAX Unsigned32 (0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Vlan Id of the ethernet interface. When the value is 0 , the VLAN access is disabled." DEFVAL { 0 } ::= { cLAplanStatsEntry 3 } cLApLanPortVlanIdValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents VLAN ID is valid or not for an ethernet interface. A value of 'true' indicates vlanId is valid. A value of 'false' indicates vlanId is not valid." DEFVAL { false } ::= { cLAplanStatsEntry 4 } cLApLanPoeState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the LAN PoE Status of an ethernet interface of an AP. A value of 'true' indicates poe state is enabled for ethernet interface. A value of 'false' indicates poe state is disabled for ethernet interface." DEFVAL { false } ::= { cLAplanStatsEntry 5 } cLAplanOverrideTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAplanOverrideEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the lan override status of an AP" ::= { ciscoLwappAplanStats 2 } cLAplanOverrideEntry OBJECT-TYPE SYNTAX CLAplanOverrideEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of LAN override status" INDEX { cLApSysMacAddress } ::= { cLAplanOverrideTable 1 } CLAplanOverrideEntry ::= SEQUENCE { cLApLanOverride TruthValue } cLApLanOverride OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the LAN port override status of AP. A value of 'true' indicates LAN override is enabled. A value of 'false' indicates LAN override is disabled." DEFVAL { false } ::= { cLAplanOverrideEntry 1 } -- ******************************************************************** -- * AP WLAN Stats. -- ******************************************************************** cLApWlanStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApWlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Per-AP, Per-Radio, Per-SSID Stats information of packets/bytes sent/received, retransmission counter, associated clients counter, etc." ::= { ciscoLwappApWlanStats 1 } cLApWlanStatsEntry OBJECT-TYPE SYNTAX CLApWlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of packets/bytes sent/received, retransmission counter, associated clients counter, and etc." INDEX { cLApSysMacAddress, cLApDot11IfType, cLWlanIndex } ::= { cLApWlanStatsTable 1 } CLApWlanStatsEntry ::= SEQUENCE { cLApWlanStatsTxPktNum Counter64, cLApWlanStatsTxOctetNum Counter64, cLApWlanStatsRxPktNum Counter64, cLApWlanStatsRxOctetNum Counter64, cLApWlanStatsRetransmitNum Counter64, cLApWlanStatsAssocClientNum Unsigned32, cLApWlanStatsOnlineUserNum Unsigned32 } cLApWlanStatsTxPktNum OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the transmitted packets counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 1 } cLApWlanStatsTxOctetNum OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the transmitted bytes counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 2 } cLApWlanStatsRxPktNum OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the received packets counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 3 } cLApWlanStatsRxOctetNum OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the received bytes counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 4 } cLApWlanStatsRetransmitNum OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the packet retransmission counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 5 } cLApWlanStatsAssocClientNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the associated client counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 6 } cLApWlanStatsOnlineUserNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the online user counter of the specific radio and wlan on this access point." ::= { cLApWlanStatsEntry 7 } -- ******************************************************************** -- * AP Station Mgmt(SMT) Parameters -- ******************************************************************** cLApIfSmtParamTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApIfSmtParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the station management information in the APs that have joined the controller. Information populated through the entries of this table is used by the AP to perform the expected 802.11 operations on the respective dot11 interfaces to coordinate with other 802.11 devices in the network. Since this table has the indices defined in the tables cLApTable and cLApDot11IfTable, an entry in this table is automatically removed when the respective entry is removed in either of those tables." ::= { ciscoLwappAp 2 } cLApIfSmtParamEntry OBJECT-TYPE SYNTAX CLApIfSmtParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the information pertaining to one particular dot11 interface of this AP used to perform the 802.11 protocol operations on the respective dot11 interface. Rows are added or deleted to this table when APs join or leave the controller respectively." INDEX { cLApSysMacAddress, cLApDot11IfSlotId } ::= { cLApIfSmtParamTable 1 } CLApIfSmtParamEntry ::= SEQUENCE { cLApIfSmtDot11Bssid MacAddress } cLApIfSmtDot11Bssid OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the base BSSID of this AP, which is the MAC address of the radio interface of this AP." ::= { cLApIfSmtParamEntry 1 } -- ******************************************************************** -- Country code setting for APs that have joined the controller -- ******************************************************************** cLApCountryTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApCountryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the country settings for the 802.11 LWAPP Access Points that have joined the controller. An entry is automatically added by the controller when a Access Point joins the controller. The entry is removed when Access Point disasscociates from the controller." ::= { ciscoLwappAp 3 } cLApCountryEntry OBJECT-TYPE SYNTAX CLApCountryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides country setting about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose their association with the controller due to loss of communication." INDEX { cLApSysMacAddress } ::= { cLApCountryTable 1 } CLApCountryEntry ::= SEQUENCE { cLApCountryCode SnmpAdminString, cLApCountryAllowed SnmpAdminString } cLApCountryCode OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the country in which the AP is operating. This value is the 3 letter country code." ::= { cLApCountryEntry 1 } cLApCountryAllowed OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the country in which the AP is operating. This value is a list of country codes sperated by comma." ::= { cLApCountryEntry 2 } -- ******************************************************************** -- * Halo BLE Configuration to set Beacon parameters of Halo enabled APs -- ******************************************************************** cLHaloGlobalBleBeaconInterval OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the beacon interval between each transmissions from BLE module. This value is common to HALO enabled APs that have joined the controller." DEFVAL { 1 } ::= { ciscoLwappApGlobalBleBeacon 1 } cLHaloBleBeaconTable OBJECT-TYPE SYNTAX SEQUENCE OF CLHaloBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the BLE global configuration.It lists the ibeacon's identification number and attenuation value which is common to HALO enabled AP's that have joined the controller." ::= { ciscoLwappApGlobalBleBeacon 2 } cLHaloBleBeaconEntry OBJECT-TYPE SYNTAX CLHaloBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains BLE global configuration which lists the ibeacon's identification number and attenuation value of HALO enabled APs that have joined the controller." INDEX { cLHaloGlobalBleBeaconId } ::= { cLHaloBleBeaconTable 1 } CLHaloBleBeaconEntry ::= SEQUENCE { cLHaloGlobalBleBeaconId Unsigned32, cLHaloGlobalBleBeaconUuid SnmpAdminString, cLHaloGlobalBleBeaconTxPower Unsigned32, cLHaloGlobalBleBeaconEnable TruthValue } cLHaloGlobalBleBeaconId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the BLE ibeacon ID for which gloabl BLE configurations to be applied." ::= { cLHaloBleBeaconEntry 1 } cLHaloGlobalBleBeaconUuid OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the UUID (universally unique identifier) which is a 128-bit value." ::= { cLHaloBleBeaconEntry 2 } cLHaloGlobalBleBeaconTxPower OBJECT-TYPE SYNTAX Unsigned32 (0..52) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies TX power of particular ibeacon for HALO enabled APs that have joined the controller.The TX power is based on size of proximity zone needed." ::= { cLHaloBleBeaconEntry 3 } cLHaloGlobalBleBeaconEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of the BLE beacons. A value of 'true' indicates BLE beacon is enabled. A value of 'false' indicates BLE beacon is disabled." ::= { cLHaloBleBeaconEntry 4 } cLApBleBeaconTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents BLE ibeacon's AP specific configuration for HALO enabled APs that have joined the controller." ::= { ciscoLwappApGlobalBleBeacon 3 } cLApBleBeaconEntry OBJECT-TYPE SYNTAX CLApBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains BLE Beacon's AP specific configuration." INDEX { cLApSysMacAddress, cLHaloGlobalBleBeaconId } ::= { cLApBleBeaconTable 1 } CLApBleBeaconEntry ::= SEQUENCE { cLApBleBeaconMajorField Unsigned32, cLApBleBeaconMinorField Unsigned32, cLApBleBeaconTxPower Unsigned32, cLApBleBeaconStatus TruthValue, cLApBleBeaconUuid SnmpAdminString, cLApBleBeaconInterval Unsigned32, cLApBleBeaconApplyGlobal TruthValue, cLApBleBeaconAdvTxPower Unsigned32 } cLApBleBeaconMajorField OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Major value of ibeacon that is used to differentiate ibeacons that have the same proximity UUID." ::= { cLApBleBeaconEntry 1 } cLApBleBeaconMinorField OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Minor value of ibeacon that is used to differentiate ibeacons that have the same proximity UUID and has same major value." ::= { cLApBleBeaconEntry 2 } cLApBleBeaconTxPower OBJECT-TYPE SYNTAX Unsigned32 (0..52) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies TX power of particular ibeacon for specified HALO enabled AP. The TX power value is based on the size of proximity zone needed." ::= { cLApBleBeaconEntry 3 } cLApBleBeaconStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of the BLE beacons. A value of 'true' indicates BLE beacon is enabled, A value of 'false' indicates BLE beacon is disabled." ::= { cLApBleBeaconEntry 4 } cLApBleBeaconUuid OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the UUID (universally unique identifier) which is a 128-bit value." ::= { cLApBleBeaconEntry 5 } cLApBleBeaconInterval OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the beacon interval between each transmissions from BLE module. This value is common to HALO enabled APs that have joined the controller." DEFVAL { 1 } ::= { cLApBleBeaconEntry 6 } cLApBleBeaconApplyGlobal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to clear all BLE configuration at AP. A value of 'true' indicates configurations need to be cleared. A value of 'false' indicates configurations need not be cleared." DEFVAL { false } ::= { cLApBleBeaconEntry 7 } cLApBleBeaconAdvTxPower OBJECT-TYPE SYNTAX Unsigned32 (40..100) UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the beacon advertised transmission power in the BLE beacon payload. This value is common to all beacons for a single AP." DEFVAL { 59 } ::= { cLApBleBeaconEntry 8 } -- ******************************************************************** -- * Halo BLE Module Mibs -- ******************************************************************** -- ******************************************************************** -- * Halo Hyperlocation Config Mibs -- ******************************************************************** cLApHyperlocationTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApHyperlocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the APs hyperlocation state and its config nature controller." ::= { ciscoLwappApHyperlocation 1 } cLApHyperlocationEntry OBJECT-TYPE SYNTAX CLApHyperlocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about Hyperlocation state and config nature of APs controller." INDEX { cLApSysMacAddress } ::= { cLApHyperlocationTable 1 } CLApHyperlocationEntry ::= SEQUENCE { cLApHyperlocationAdminState TruthValue, cLApHyperlocationUnsetFlag TruthValue } cLApHyperlocationAdminState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the hyperlocation admin state for an AP to be enabled or disabled. A value of 'true' indicates admin state of HALO module is up. A value of 'false' indicates admin state of HALO module is down." ::= { cLApHyperlocationEntry 1 } cLApHyperlocationUnsetFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies explicit flag status for AP need to be enabled or not. A value of 'true' indicates AP has an explicit per AP config. A value of 'false' indicates there is no AP config" ::= { cLApHyperlocationEntry 2 } -- ******************************************************************** -- * Halo Hyperlocation Config Mibs -- ******************************************************************** -- ******************************************************************** -- * Notification Control Object -- ******************************************************************** ciscoLwappApIfRegulatoryDomainMismatchNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappApIfRegulatoryDomainMismatchNotif notification. A value of 'true' indicates that the agent generates ciscoLwappApIfRegulatoryDomainMismatchNotif notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappApIfRegulatoryDomainMismatchNotif notification." DEFVAL { true } ::= { ciscoLwappAp 4 } ciscoLwappApCrashEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappApCrash notification. A value of 'true' indicates that the agent generates ciscoLwappApCrash notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappApCrash notification." DEFVAL { true } ::= { ciscoLwappAp 5 } ciscoLwappApUnsupportedEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappApUnsupported notification. A value of 'true' indicates that the agent generates ciscoLwappApUnsupported notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappApUnsupported notification." DEFVAL { true } ::= { ciscoLwappAp 6 } ciscoLwappApAssociatedEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappApAssociated notification. A value of 'true' indicates that the agent generates ciscoLwappApAssociated notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappApAssociated notification." DEFVAL { true } ::= { ciscoLwappAp 7 } ciscoLwappXorRadioRoleChangeEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappApXorRadioRoleChangeNotify notification. A value of 'true' indicates that the agent generates ciscoLwappApXorRadioRoleChangeNotify notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappApXorRadioRoleChangeNotify notification." DEFVAL { true } ::= { ciscoLwappAp 13 } -- ******************************************************************** -- Spectrum Expert Connection parameters -- ******************************************************************** cLApSeClientTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApSeClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the details of Spectrum Expert client connected to radio interface of APs" ::= { ciscoLwappApMIBObjects 8 } cLApSeClientEntry OBJECT-TYPE SYNTAX CLApSeClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the details of Spectrum Expert client connected to APs" INDEX { cLApSysMacAddress, cLApDot11IfSlotId, cLApSeIndex } ::= { cLApSeClientTable 1 } CLApSeClientEntry ::= SEQUENCE { cLApSeIndex Integer32, cLApSeClientUserName SnmpAdminString, cLApSeClientIPAddrType InetAddressType, cLApSeClientIPAddr InetAddress, cLApSeClientDuration TimeInterval, cLApSeClientPort InetPortNumber } cLApSeIndex OBJECT-TYPE SYNTAX Integer32 (0..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the index of the client running the Spectrum Expert instance." ::= { cLApSeClientEntry 1 } cLApSeClientUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the client running the Spectrum Expert application" ::= { cLApSeClientEntry 2 } cLApSeClientIPAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the client IP address type, that runs the SE application, made available through cLApSeClientIPAddr" ::= { cLApSeClientEntry 3 } cLApSeClientIPAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the client IP address, that runs the SE application" ::= { cLApSeClientEntry 4 } cLApSeClientDuration OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the duration for which the SE client application has been up and running" ::= { cLApSeClientEntry 5 } cLApSeClientPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the port from which the SE client application is running" ::= { cLApSeClientEntry 6 } -- ******************************************************************** -- Global settings for APs -- ******************************************************************** cLApFastHbTimerTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApFastHbTimerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries for AP fast heartbeat timers configured in the controller. At startup, all the entries in this table are set up by the central controller. A management application can later change the values in this table." ::= { ciscoLwappApGlobal 1 } cLApFastHbTimerEntry OBJECT-TYPE SYNTAX CLApFastHbTimerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in cLApFastHbTimerTable. There is an entry in this table for each AP type, as identified by a value of cLApFastHbTimerApType." INDEX { cLApFastHbTimerApType } ::= { cLApFastHbTimerTable 1 } CLApFastHbTimerEntry ::= SEQUENCE { cLApFastHbTimerApType INTEGER, cLApFastHbTimerTimeout Unsigned32, cLApFastHbTimerEnabled TruthValue } cLApFastHbTimerApType OBJECT-TYPE SYNTAX INTEGER { local(1), hreap(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the AP type for this entry. local - indicates that timer is for local mode APs hreap - indicates that timer is for HREAP APs" ::= { cLApFastHbTimerEntry 1 } cLApFastHbTimerTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..15) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the timeout value for the heart beat timer. This value changes to 0 when cLApFastHbTimerEnabled is set to 'false'." ::= { cLApFastHbTimerEntry 2 } cLApFastHbTimerEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the heartbeat timer. A value of 'true' indicates that this timer is enabled. A value of 'false' indicates that this timer is disabled." ::= { cLApFastHbTimerEntry 3 } cLApPrimaryDiscoveryTimeout OBJECT-TYPE SYNTAX Unsigned32 (30..3600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the timeout for the primary AP discovery." DEFVAL { 120 } ::= { ciscoLwappApGlobal 3 } cLApGlobalPrimaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the primary controller's address made available through cLApPrimaryControllerAddress." ::= { ciscoLwappApGlobal 4 } cLApGlobalPrimaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the primary controller that the APs will join. The name and address should be provided in the same set request. An address of all zeros will unset the primary controller." ::= { ciscoLwappApGlobal 5 } cLApGlobalPrimaryControllerName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the name of the primary controller that the APs will join." ::= { ciscoLwappApGlobal 6 } cLApGlobalSecondaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the secondary controller's address made available through cLApSecondaryControllerAddress." ::= { ciscoLwappApGlobal 7 } cLApGlobalSecondaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the secondary controller that the APs will join. The name and address should be provided in the same set request. An address of all zeros will unset the secondary controller." ::= { ciscoLwappApGlobal 8 } cLApGlobalSecondaryControllerName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the name of the secondary controller that the APs will join." ::= { ciscoLwappApGlobal 9 } cLApGlobalFailoverPriority OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the global AP failover priority. If Enabled, Priorities will be considered of the APs which wishes to join the controller. Preference will be given to the higher priority AP. If the number of associated AP has already reached the limit then the controller will disassociate a lower priority AP to accomodate a higher priority AP. Default is Disabled state." DEFVAL { false } ::= { ciscoLwappApGlobal 10 } cLApGlobalTcpMss OBJECT-TYPE SYNTAX Integer32 (0 | 536..1363) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Global AP TCP MSS value. Permissible value are between 536 and 1363. This will also enable the global TCP MSS flag. Value of 0 will disable the global TCP MSS flag. Any change of value for this object will be reflected to cLApTcpMss" ::= { ciscoLwappApGlobal 11 } cLApGlobalDot11IfTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApGlobalDot11IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the global dot11 parameters per slot id, represented by cLApDot11IfSlotId, of the radio interface in all the APs joined with the controller." ::= { ciscoLwappApGlobal 12 } cLApGlobalDot11IfEntry OBJECT-TYPE SYNTAX CLApGlobalDot11IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents an entry in the cLApGlobalDot11IfTable." INDEX { cLApDot11IfSlotId } ::= { cLApGlobalDot11IfTable 1 } CLApGlobalDot11IfEntry ::= SEQUENCE { cLApGlobalDot11IfCdpEnabled TruthValue } cLApGlobalDot11IfCdpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to configure the Cisco Discovery Protocol(CDP) in the interface, represented by cLApDot11IfSlotId of the all the APs, joined in the controller. Setting this object to a value of 'true' would turn on the CDP on this slot. Setting this object to a value of 'false' would turn off the CDP on this slot, so that CDP advertisements are not sent. Read operation on this attribute will not be supported. When queried this will return a value of 'false'." ::= { cLApGlobalDot11IfEntry 1 } cLApGlobalEthernetIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApGlobalEthernetIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the global parameters on Ethernet interfaces of all the APs joined with the controller." ::= { ciscoLwappApGlobal 13 } cLApGlobalEthernetIfEntry OBJECT-TYPE SYNTAX CLApGlobalEthernetIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This represents an entry in cLApGlobalEthernetIfTable." INDEX { cLApEthernetIfSlotId } ::= { cLApGlobalEthernetIfTable 1 } CLApGlobalEthernetIfEntry ::= SEQUENCE { cLApGlobalEthernetIfCdpEnabled TruthValue } cLApGlobalEthernetIfCdpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is specifies to configure the Cisco Discovery Protocol(CDP) in the interface, represented by cLApEthernetIfSlotId of the all the APs, joined in the controller. Setting this object to a value of 'true' would turn on the CDP on this ethernet interface. Setting this object to a value of 'false' would turn off the CDP on this ethernet interface, so that CDP advertisements are not sent. Read operation on this attribute will not be supported. When queried this will return a value of 'false'." ::= { cLApGlobalEthernetIfEntry 1 } cLApGlobalRetransmitCount OBJECT-TYPE SYNTAX Unsigned32 UNITS "retries" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission count for the Control Packet of all the Access Points, joined to this controller. This value specifies the number of packets retransmitted after which the Access Point falls back to another controller in case of failover." ::= { ciscoLwappApGlobal 14 } cLApGlobalRetransmitTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission timeout for the Control Packet of all the Access Points, joined to this controller. This value specifies the timeout for each retransmission, during the fallback of Access Point to another controller in case of failover." ::= { ciscoLwappApGlobal 15 } cLApOeapDisableLocalAccess OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the local access is supported for all the Office Extended Access Points, joined to this controller. If set to true, the local SSID and and LAN ports on the OEAP will be disabled." ::= { ciscoLwappApGlobal 16 } cLApGlobalLEDState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the LED state of all the access points should be enabled or disabled." ::= { ciscoLwappApGlobal 17 } cLApRadioInterfaceShutdownEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to enable or disable AP radio Interface. When enabled, AP radio's will be shut down when Ethernet link goes down for a duration of time set for cLApEthernetInterfaceDowntime. A value of 'true' indicates the AP radio interface shutdown is enabled. A value of 'false' indicates the AP radio interface shutdown is disabled." ::= { ciscoLwappApGlobal 18 } cLApEthernetInterfaceDowntime OBJECT-TYPE SYNTAX Unsigned32 UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the ethernet interface down time after which the AP radio interface will be shut down." ::= { ciscoLwappApGlobal 19 } cLAPMulticastGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP multicast group address type." ::= { ciscoLwappApGlobal 20 } cLAPMulticastGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP multicast group address." ::= { ciscoLwappApGlobal 21 } cLAPMulticastMode OBJECT-TYPE SYNTAX INTEGER { unicast(1), multicast(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the switch's ethernet multicast support. unicast - Controller will convert multicast to unicast packet. multicast - Multicast mode is enabled." ::= { ciscoLwappApGlobal 22 } cLApPrimedDiscoveryTimeout OBJECT-TYPE SYNTAX Integer32 (0 | 120..43200) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the primed timeout for the AP discovery." ::= { ciscoLwappApGlobal 23 } cLApGlobalPreferMode OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the global capwap prefer-mode. ipv4 - capwap tunnel established with ipv4 address. ipv6 - capwap tunnel established with ipv6 address." ::= { ciscoLwappApGlobal 24 } cLApGlobalAPLagCapability OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the ap-lag capability state of all the access points should be enabled or disabled. A value of 'true' indicates ap-lag capapbility is enabled. A value of 'false' indicates ap-lag capapbility is disabled." ::= { ciscoLwappApGlobal 25 } cLApGlobalAPDtlsVersion OBJECT-TYPE SYNTAX INTEGER { dtls10(1), dtls12(2), dtlsall(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the dtls version of ap" ::= { ciscoLwappApGlobal 26 } cLApGlobalAPDtlsCipherSuite OBJECT-TYPE SYNTAX INTEGER { rsaaes128sha1(47), dhersaaes128cbcsha(51), rsaaes256sha1(53), dhersaaes256cbcsha(57), rsaaes256sha256(61), rsagcm128sha256(156), rsagcm256sha384(157), ecdsaaes128gcmsha256(49195), ecdsaaes256gcmsha384(49196), dhersaaes256cbcsha256(49197) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the dtls cipher suite of ap" ::= { ciscoLwappApGlobal 27 } cLApGlobalMaxApsSupported OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum number of APs supported by this controller." ::= { ciscoLwappApGlobal 28 } cLApAuthorizeApMacAuth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag specifies the status of mac auth" ::= { ciscoLwappApGlobal 30 } cLApAuthorizeApSerialNumAuth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag specifies the status of serial number auth" ::= { ciscoLwappApGlobal 31 } cLApAuthorizeApMethodList OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the method list used for the AP authorization when enabled. The default method list is default" ::= { ciscoLwappApGlobal 32 } -- ******************************************************************** -- * AP Dot11 Interface Antenna Information -- ******************************************************************** cLApDot11IfAntennaTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11IfAntennaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters corresponding to the antenna on dot11 interfaces of the APs that have joined the controller." ::= { ciscoLwappApIf 4 } cLApDot11IfAntennaEntry OBJECT-TYPE SYNTAX CLApDot11IfAntennaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association." INDEX { cLApSysMacAddress, cLApDot11IfSlotId, cLApDot11IfAntennaId } ::= { cLApDot11IfAntennaTable 1 } CLApDot11IfAntennaEntry ::= SEQUENCE { cLApDot11IfAntennaId Unsigned32, cLApDot11IfAntennaTxEnable TruthValue, cLApDot11IfAntennaRxEnable TruthValue, cLApDot11IfAntennaEnable TruthValue } cLApDot11IfAntennaId OBJECT-TYPE SYNTAX Unsigned32 (1..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the antenna ID of a dot11 interface on an AP. The antenna Id for a particular dot11 interface on a slot as represented by this object." ::= { cLApDot11IfAntennaEntry 1 } cLApDot11IfAntennaTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether this antenna is allowed to trasmit or not. A value of 'true' enables the antenna to transmit. A value of 'false' disables the antenna to transmit. This object has been deprecated for cLApDot11IfAntennaEnable. cLApDot11IfAntennaTxEnable object is superseded by cLApDot11IfAntennaEnable." DEFVAL { true } ::= { cLApDot11IfAntennaEntry 2 } cLApDot11IfAntennaRxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether this antenna is allowed to recieve or not. A value of 'true' enables the antenna to receive. A value of 'false' disables the antenna to receive. cLApDot11IfAntennaRxEnable object is superseded by cLApDot11IfAntennaEnable." DEFVAL { true } ::= { cLApDot11IfAntennaEntry 3 } cLApDot11IfAntennaEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether this antenna is enabled or not. A value of 'true' indicates antenna is enabled. A value of 'false' indicates antenna is disabled." DEFVAL { true } ::= { cLApDot11IfAntennaEntry 4 } -- ******************************************************************** -- * AP Vlan Tagging -- ******************************************************************** cLApVlanIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApVlanIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters corresponding to the ethernet interfaces of the APs that have joined the controller." ::= { ciscoLwappApIf 5 } cLApVlanIfEntry OBJECT-TYPE SYNTAX CLApVlanIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the VLAN functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the administrator creates an entry in this table." INDEX { cLApSysMacAddress, cLApVlanIfEthernetId } ::= { cLApVlanIfTable 1 } CLApVlanIfEntry ::= SEQUENCE { cLApVlanIfEthernetId Unsigned32, cLApVlanIfMode INTEGER, cLApVlanIfEnable TruthValue, cLApVlanIfNativeVlanId Unsigned32 } cLApVlanIfEthernetId OBJECT-TYPE SYNTAX Unsigned32 (0..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the ID of a ethernet interface on an AP." ::= { cLApVlanIfEntry 1 } cLApVlanIfMode OBJECT-TYPE SYNTAX INTEGER { normal(1), access(2), trunk(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP's ethernet interface is configured for. normal - VLAN is not operating in access or trunk. access - VLAN is operating in access mode trunk - VLAN is operating in trunk mode." DEFVAL { normal } ::= { cLApVlanIfEntry 2 } cLApVlanIfEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether this interface is enabled or not. A value of 'true' enables the interface. A value of 'false' disables the interface.. This will delete all entries on this AP's ethernet interface." DEFVAL { true } ::= { cLApVlanIfEntry 3 } cLApVlanIfNativeVlanId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the native VLAN ID assigned to this AP's ethernet interface. This only applies when the icLApVlanIfMode is set to 'trunk'. For all other modes this return a value of zero." ::= { cLApVlanIfEntry 4 } -- ******************************************************************** -- * AP Vlan Tagging -- ******************************************************************** cLApVlanListTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApVlanListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the basic functional parameters corresponding to the VLAN Ethernet interfaces of the APs that have joined the controller." ::= { ciscoLwappApIf 6 } cLApVlanListEntry OBJECT-TYPE SYNTAX CLApVlanListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the VLAN functional parameters of the Ethernet interface of an AP that has joined the controller. Entries are added when the administrator creates an entry in this table." INDEX { cLApSysMacAddress, cLApVlanIfEthernetId, cLApVlanListVlanId } ::= { cLApVlanListTable 1 } CLApVlanListEntry ::= SEQUENCE { cLApVlanListVlanId Unsigned32, cLApVlanListRowStatus RowStatus } cLApVlanListVlanId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the ID assigned to the VLAN on this AP's ethernet interface." ::= { cLApVlanListEntry 1 } cLApVlanListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies to add or delete an entry in this table." ::= { cLApVlanListEntry 2 } -- ******************************************************************** -- * Global AP 802.1x Supplicant Credentials -- ******************************************************************** cLApGlobal802dot1xAuthenticationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Global AP 802.1x Supplicant Authentication feature. If configured as True, user can configure 8021.1x authentication between lightweight access points and the switch. The access point acts as an 802.1x supplicant and is authenticated by the switch using EAP-FAST with anonymous PAC provisioning.User can set global authentication settings that all access points inherit as they join the controller. This includes all access points that are currently joined to the controller and any that join in the future. If desired, user can override the global authentication settings and assign unique authentication settings for a specific access point. Default state is False." DEFVAL { false } ::= { ciscoLwappAp802dot1xSupplicant 1 } cLApGlobal802dot1xSupplicantUsername OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the 802.1x supplicant username that is to be inherited by all access points that join the controller." ::= { ciscoLwappAp802dot1xSupplicant 2 } cLApGlobal802dot1xSupplicantPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the 802.1x supplicant Password that is to be inherited by all access points that join the controller. A query on this OID will always return '****'." ::= { ciscoLwappAp802dot1xSupplicant 3 } cLApGlobal802dot1xSupplicantEapType OBJECT-TYPE SYNTAX INTEGER { none(1), eapFast(2), eapTls(3), peap(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the EAP type to be applied for ap port auth as Global config." ::= { ciscoLwappAp802dot1xSupplicant 5 } -- ******************************************************************** -- * Per AP 802.1x Supplicant Credentials -- ******************************************************************** cLAp802dot1xSupplicantTable OBJECT-TYPE SYNTAX SEQUENCE OF CLAp802dot1xSupplicantEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the information about the 802.1x Supplicant credentials of the 802.11 LWAPP Access Points that have joined the controller. Rows are added to this table whenever, new APs are joined to this controller, and rows are deleted whenever APs gets disjoined from the controller." ::= { ciscoLwappAp802dot1xSupplicant 4 } cLAp802dot1xSupplicantEntry OBJECT-TYPE SYNTAX CLAp802dot1xSupplicantEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. cLApSysMacAddress is the index which uniquely identifies every row in the table." INDEX { cLApSysMacAddress } ::= { cLAp802dot1xSupplicantTable 1 } CLAp802dot1xSupplicantEntry ::= SEQUENCE { cLAp802dot1xSupplicantOverrideEnabled TruthValue, cLAp802dot1xSupplicantOverrideUsername SnmpAdminString, cLAp802dot1xSupplicantOverridePassword SnmpAdminString, cLAp802dot1xSupplicantOverrideEapType INTEGER } cLAp802dot1xSupplicantOverrideEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the individual AP level 802.1x Supplicant Authentication override parameters. A value of 'true' indicates user can override the Global AP 8021.1x authentication credentials by providing individual AP level credentials. A value of 'false' indicates user cannot override the Global AP 802.1x authentication credentials." DEFVAL { false } ::= { cLAp802dot1xSupplicantEntry 1 } cLAp802dot1xSupplicantOverrideUsername OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the individual AP level 802.1x supplicant override username." ::= { cLAp802dot1xSupplicantEntry 2 } cLAp802dot1xSupplicantOverridePassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object the individual AP level 802.1x supplicant override password. A query on this OID will always return '****'." ::= { cLAp802dot1xSupplicantEntry 3 } cLAp802dot1xSupplicantOverrideEapType OBJECT-TYPE SYNTAX INTEGER { none(1), eapFast(2), eapTls(3), peap(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the EAP type to be applied for ap port auth as AP override config." ::= { cLAp802dot1xSupplicantEntry 4 } -- ******************************************************************** -- * AP WLAN Stats. -- ******************************************************************** cLApWlanInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApWlanInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Per-AP, Per-SSID information of max supported clients" ::= { ciscoLwappApWlanInfo 1 } cLApWlanInfoEntry OBJECT-TYPE SYNTAX CLApWlanInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the information about clients associated to a wlan broadcasted by an access point." INDEX { cLApSysMacAddress, cLWlanIndex } ::= { cLApWlanInfoTable 1 } CLApWlanInfoEntry ::= SEQUENCE { cLApWlanInfoMaxClients Unsigned32 } cLApWlanInfoMaxClients OBJECT-TYPE SYNTAX Unsigned32 (1..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum supported clients per WLAN ." DEFVAL { 600 } ::= { cLApWlanInfoEntry 1 } cLApRadioWlanInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApRadioWlanInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Per-AP, Per-radio, Per-SSID information." ::= { ciscoLwappApWlanInfo 2 } cLApRadioWlanInfoEntry OBJECT-TYPE SYNTAX CLApRadioWlanInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information of Per-AP, Per-RADIO, Per-SSID information." INDEX { cLApSysMacAddress, cLApDot11IfSlotId, cLWlanIndex } ::= { cLApRadioWlanInfoTable 1 } CLApRadioWlanInfoEntry ::= SEQUENCE { cLApRadioWlanSsid SnmpAdminString, cLApRadioWlanBssid MacAddress } cLApRadioWlanSsid OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents SSID of the particular WLAN, which is seen on the radio of the AP." ::= { cLApRadioWlanInfoEntry 1 } cLApRadioWlanBssid OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the BSSID of the SSID on this radio of this AP." ::= { cLApRadioWlanInfoEntry 2 } -- ******************************************************************** -- * Radio Level Configs -- ******************************************************************** cLApDot11GlobalConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11GlobalConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the information about the global attributes of the radio interface, that would be applicable for all the APs that join the controller." ::= { ciscoLwappApIf 7 } cLApDot11GlobalConfigEntry OBJECT-TYPE SYNTAX CLApDot11GlobalConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the network level configurations of the radio interface. Entries cannot be added or deleted in this table." INDEX { cLApDot11IfType } ::= { cLApDot11GlobalConfigTable 1 } CLApDot11GlobalConfigEntry ::= SEQUENCE { cLApNwLegacyBeamForming INTEGER, cLApNwTxPowerThreshold Integer32, cLApNwTxPowerThresholdVer2 Integer32 } cLApNwLegacyBeamForming OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notApplicable(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object indicates the status of legacy beam forming in this AP. This object is applicable only for 11n supported APs. For APs that does not support legacy beam forming, a get request on this attribute will return the value 'notApplicable'. A value of 'enable' indicates that the legacy Beam forming is enabled in this AP. A value of 'false' indicates that the legacy Beam forming is disabled in this AP." DEFVAL { notApplicable } ::= { cLApDot11GlobalConfigEntry 1 } cLApNwTxPowerThreshold OBJECT-TYPE SYNTAX Integer32 (-80..-50) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Global AP Transmit Power Threshold value. The permissible range is -80 dbm to -50 dbm" DEFVAL { -70 } ::= { cLApDot11GlobalConfigEntry 2 } cLApNwTxPowerThresholdVer2 OBJECT-TYPE SYNTAX Integer32 (-80..-50) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Global AP Transmit Power Threshold value when Inteference Optimal mode of Tx Power Control (TPC v2) is enabled. The permissible range is -80 dbm to -50 dbm" DEFVAL { -67 } ::= { cLApDot11GlobalConfigEntry 3 } -- ******************************************************************** -- * Ap Global Cipher Configurations -- ******************************************************************** cLApSecureCipher OBJECT-TYPE SYNTAX INTEGER { disable(1), aes256sha1(2), aes256sha2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the secure ciphers, AES256+SHA or AES256+SHA2 for CAPWAP control tunnel. disable - This value indicates that AP and controller will continue to use default ciphers for CAPWAP tunnel. aes256sha1 - This value indicates that AP and controller will use AES256+SHA cipher for CAPWAP tunnel. aes256sha2 - This value indicates that AP and controller will use AES256+SHA2 cipher for CAPWAP tunnel." ::= { ciscoLwappApSecureCipher 1 } -- ******************************************************************** -- * AP Dot11 radio statistics Information -- ******************************************************************** cLApDot11RadioStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11RadioStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the statistics information about the radios of the APs that have joined the controller." ::= { ciscoLwappApIf 8 } cLApDot11RadioStatsEntry OBJECT-TYPE SYNTAX CLApDot11RadioStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a statistics of the radio of an AP that has joined the conttroller. Entries are added when the APs associate to this controller and deleted when they lose their association." INDEX { cLApSysMacAddress, cLApDot11IfSlotId } ::= { cLApDot11RadioStatsTable 1 } CLApDot11RadioStatsEntry ::= SEQUENCE { cLApDot11RadioStatsRxErrorFrameCount Counter32, cLApDot11RadioStatsMacMicErrFrameCount Counter32, cLApDot11RadioStatsMacDecryptErrFrameCount Counter32, cLApDot11RadioStatsRxMgmtFrameCount Counter32, cLApDot11RadioStatsRxCtrlFrameCount Counter32, cLApDot11RadioStatsRxDataFrameCount Counter32, cLApDot11RadioStatsTxMgmtFrameCount Counter32, cLApDot11RadioStatsTxCtrlFrameCount Counter32, cLApDot11RadioStatsTxDataFrameCount Counter32, cLApDot11RadioStatsRxDataPacketCount Counter32, cLApDot11RadioStatsTxDataPacketCount Counter32, cLApDot11RadioStatsRetryFrameCount Counter32, cLApDot11RadioStatsRetryPacketCount Counter32 } cLApDot11RadioStatsRxErrorFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of error frames received on the radio." ::= { cLApDot11RadioStatsEntry 1 } cLApDot11RadioStatsMacMicErrFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of frames with wrong MIC received by AP on the radio." ::= { cLApDot11RadioStatsEntry 2 } cLApDot11RadioStatsMacDecryptErrFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of frames with destroyed encrypted data received by AP on the radio." ::= { cLApDot11RadioStatsEntry 3 } cLApDot11RadioStatsRxMgmtFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of management frame received on the radio." ::= { cLApDot11RadioStatsEntry 4 } cLApDot11RadioStatsRxCtrlFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of control frame received on the radio." ::= { cLApDot11RadioStatsEntry 5 } cLApDot11RadioStatsRxDataFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of data frame received on the radio." ::= { cLApDot11RadioStatsEntry 6 } cLApDot11RadioStatsTxMgmtFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of management frame transmitted on the radio." ::= { cLApDot11RadioStatsEntry 7 } cLApDot11RadioStatsTxCtrlFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of control frame transmitted on the radio." ::= { cLApDot11RadioStatsEntry 8 } cLApDot11RadioStatsTxDataFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of data frame transmitted on the radio." ::= { cLApDot11RadioStatsEntry 9 } cLApDot11RadioStatsRxDataPacketCount OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of data packets received on the radio." ::= { cLApDot11RadioStatsEntry 10 } cLApDot11RadioStatsTxDataPacketCount OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of data packets transmitted on the radio." ::= { cLApDot11RadioStatsEntry 11 } cLApDot11RadioStatsRetryFrameCount OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of downstream retry frames on the radio." ::= { cLApDot11RadioStatsEntry 12 } cLApDot11RadioStatsRetryPacketCount OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total number of downstream retry packets on the radio." ::= { cLApDot11RadioStatsEntry 13 } -- ******************************************************************** -- * AP Radio Rssi Stats -- ******************************************************************* cLApDot11RadioRssiTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11RadioRssiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Per AP, Per Radio Stats information of Average, Highest, Lowest Rssi of all the clients update of the APs Radio." ::= { ciscoLwappApIf 9 } cLApDot11RadioRssiEntry OBJECT-TYPE SYNTAX CLApDot11RadioRssiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of Average, Highest and Lowest RSSI of Per AP Per Radio." INDEX { cLApSysMacAddress, cLApDot11IfType } ::= { cLApDot11RadioRssiTable 1 } CLApDot11RadioRssiEntry ::= SEQUENCE { cLApDot11RadioRssiHighest Integer32, cLApDot11RadioRssiLowest Integer32, cLApDot11RadioRssiAverage Integer32 } cLApDot11RadioRssiHighest OBJECT-TYPE SYNTAX Integer32 UNITS "dbm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Highest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio." ::= { cLApDot11RadioRssiEntry 1 } cLApDot11RadioRssiLowest OBJECT-TYPE SYNTAX Integer32 UNITS "dbm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Lowest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio." ::= { cLApDot11RadioRssiEntry 2 } cLApDot11RadioRssiAverage OBJECT-TYPE SYNTAX Integer32 UNITS "dbm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Average Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio." ::= { cLApDot11RadioRssiEntry 3 } -- ******************************************************************** -- * AP Crash file Info -- ******************************************************************** cLApCrashInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApCrashInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the crash file information for each AP. An entry is automatically added to this table when an Access Points crashes and reboots. Entry is removed from this table when AP disassociates from the controllers." ::= { ciscoLwappAp 8 } cLApCrashInfoEntry OBJECT-TYPE SYNTAX CLApCrashInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides crash information available for each AP." INDEX { cLApSysMacAddress } ::= { cLApCrashInfoTable 1 } CLApCrashInfoEntry ::= SEQUENCE { cLApCrashFileName SnmpAdminString, cLApCrashFileSize Unsigned32, cLApCrashFileTimeStamp DateAndTime } cLApCrashFileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..28)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the crash file name for a specific AP." ::= { cLApCrashInfoEntry 1 } cLApCrashFileSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the size of the crash file." ::= { cLApCrashInfoEntry 2 } cLApCrashFileTimeStamp OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the timestamp of the crash file." ::= { cLApCrashInfoEntry 3 } cLApExtTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the system information for each AP." ::= { ciscoLwappAp 10 } cLApExtEntry OBJECT-TYPE SYNTAX CLApExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides system information for each AP." INDEX { cLApSysMacAddress } ::= { cLApExtTable 1 } CLApExtEntry ::= SEQUENCE { cLApLEDFlashStatus TruthValue, cLApLEDFlashDuration Unsigned32, cLApInetAddressType InetAddressType, cLApInetAddress InetAddress, cLApStaticIpv6AddressEnabled TruthValue, cLApStaticIpv6InetAddressType InetAddressType, cLApStaticIpv6InetAddress InetAddress, cLApStaticIpv6PrefixLength Unsigned32, cLApStaticIpv6GatewayInetAddressType InetAddressType, cLApStaticIpv6GatewayInetAddress InetAddress, cLApStaticIpNetmaskType InetAddressType, cLApStaticIpNetmask InetAddress, cLApPreferMode INTEGER, cLApPreferModeApplied INTEGER } cLApLEDFlashStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of the AP LED Flash. A value of 'true' indicates LED flash is enabled. A value of 'false' indicates LED flash is disabled." ::= { cLApExtEntry 1 } cLApLEDFlashDuration OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the duration for which the AP's LED should blink. This is applicable when the value of cLApFlashStatus is TRUE. Value of 0 indicates the blinking for infinite duration." ::= { cLApExtEntry 2 } cLApInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the AP address made available through cLApInetAddress." ::= { cLApExtEntry 3 } cLApInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the Access Point." ::= { cLApExtEntry 4 } cLApStaticIpv6AddressEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies that AP is configured to use static IPv6 address. A value of 'true' indicates AP can assign with static IP address. A value of 'false' indicates AP cannot assign with static IP address." ::= { cLApExtEntry 5 } cLApStaticIpv6InetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specified the address type made available through cLApStaticIpv6InetAddress." ::= { cLApExtEntry 6 } cLApStaticIpv6InetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the static IPv6 address of the Access Point." ::= { cLApExtEntry 7 } cLApStaticIpv6PrefixLength OBJECT-TYPE SYNTAX Unsigned32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the prefix length of the static IP Address configured on the AP." ::= { cLApExtEntry 8 } cLApStaticIpv6GatewayInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specified the address type made available through cLApStaticIpv6GatewayInetAddress." ::= { cLApExtEntry 9 } cLApStaticIpv6GatewayInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the IPv6 Address of the Gateway server. This attribute can be configured only if the static IP option is turned on in the AP." ::= { cLApExtEntry 10 } cLApStaticIpNetmaskType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the netmask address type for AP's static IP." ::= { cLApExtEntry 11 } cLApStaticIpNetmask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies netmask for ipv4 address." ::= { cLApExtEntry 12 } cLApPreferMode OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the capwap prefer-mode (ipv4 or ipv6) of AP." ::= { cLApExtEntry 13 } cLApPreferModeApplied OBJECT-TYPE SYNTAX INTEGER { apgroup(1), global(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the prefer-mode of AP applied by apgroup config or global config. apgroup - capwap prefer mode applied at ap group level. global - capwap prefer mode applied globally." ::= { cLApExtEntry 14 } -- ******************************************************************** -- * AP Sys Info -- ******************************************************************** cLApSysInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApSysInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the system information for each AP." ::= { ciscoLwappAp 9 } cLApSysInfoEntry OBJECT-TYPE SYNTAX CLApSysInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides system information for each AP." INDEX { cLApSysMacAddress } ::= { cLApSysInfoTable 1 } CLApSysInfoEntry ::= SEQUENCE { cLApSysMemType SnmpAdminString, cLApSysMemSize Unsigned32, cLApSysFlashSize Unsigned32, cLApSysCpuType SnmpAdminString, cLApSysFlashType SnmpAdminString } cLApSysMemType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP system memory type." ::= { cLApSysInfoEntry 1 } cLApSysMemSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "KBytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the total AP system memory size in Kbytes." ::= { cLApSysInfoEntry 2 } cLApSysFlashSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "KBytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP flash size in Kbytes." ::= { cLApSysInfoEntry 3 } cLApSysCpuType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP cpu type" ::= { cLApSysInfoEntry 4 } cLApSysFlashType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the AP Flash type." ::= { cLApSysInfoEntry 5 } -- ******************************************************************** -- * AP Dot11 radio rate statistics Information -- ******************************************************************** cLApDot11RadioRateStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11RadioRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents per AP, per radio, per rate stats information of all the clients of the APs Radio." ::= { ciscoLwappApIf 10 } cLApDot11RadioRateStatsEntry OBJECT-TYPE SYNTAX CLApDot11RadioRateStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of Rx/Tx packets and bytes of per AP per radio per rate." INDEX { cLApSysMacAddress, cLApDot11IfSlotId, cLApDot11RadioRate } ::= { cLApDot11RadioRateStatsTable 1 } CLApDot11RadioRateStatsEntry ::= SEQUENCE { cLApDot11RadioRate Unsigned32, cLApDot11RadioRateStatsRxPackets Counter32, cLApDot11RadioRateStatsRxBytes Counter32, cLApDot11RadioRateStatsTxPackets Counter32, cLApDot11RadioRateStatsTxBytes Counter32, cLApDot11RadioRateString SnmpAdminString } cLApDot11RadioRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the data rate value for a particular band." ::= { cLApDot11RadioRateStatsEntry 1 } cLApDot11RadioRateStatsRxPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of packets received for the specific radio and data rate on this access point." ::= { cLApDot11RadioRateStatsEntry 2 } cLApDot11RadioRateStatsRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of bytes received for the specific radio and data rate on this access point." ::= { cLApDot11RadioRateStatsEntry 3 } cLApDot11RadioRateStatsTxPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of packets transmitted from the specific radio and data rate on this access point." ::= { cLApDot11RadioRateStatsEntry 4 } cLApDot11RadioRateStatsTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of bytes transmitted from the specific radio and data rate on this access point." ::= { cLApDot11RadioRateStatsEntry 5 } cLApDot11RadioRateString OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the data rate in a user-friendly text string format." ::= { cLApDot11RadioRateStatsEntry 6 } cLApPacketDumpFtpServerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address type of the server to which the packet dump is stored." ::= { ciscoLwappPacketDumpInfo 1 } cLApPacketDumpFtpServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the server to which the packet dump is stored." ::= { ciscoLwappPacketDumpInfo 2 } cLApPacketDumpFtpServerPath OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the directory path for the packet dump storing. The controller remembers the last file path used." ::= { ciscoLwappPacketDumpInfo 3 } cLApPacketDumpFtpUsername OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to store the FTP username for transferring the packet-dump to the FTP server." ::= { ciscoLwappPacketDumpInfo 4 } cLApPacketDumpFtpPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the FTP server login password to store the packet dump." ::= { ciscoLwappPacketDumpInfo 5 } cLApPacketDumpClassifier OBJECT-TYPE SYNTAX BITS { management(0), data(1), control(2), dot1x(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Frame Type considered for packet-dump." ::= { ciscoLwappPacketDumpInfo 6 } cLApPacketDumpBufferSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the buffer size considered for packet-dump." ::= { ciscoLwappPacketDumpInfo 7 } cLApPacketDumpCaptureTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the capture time considered for packet-dump." ::= { ciscoLwappPacketDumpInfo 8 } cLApPacketDumpTruncation OBJECT-TYPE SYNTAX Unsigned32 UNITS "bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of the packet after truncation" ::= { ciscoLwappPacketDumpInfo 9 } cLApPacketDumpApName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP name on which we need to start packet dump." ::= { ciscoLwappPacketDumpInfo 10 } cLApPacketDumpDeviceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the MAC address of the device for which we need to start packet dump on the AP." ::= { ciscoLwappPacketDumpInfo 11 } cLApPacketDumpStartStop OBJECT-TYPE SYNTAX INTEGER { start(1), stop(2), none(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies user to start or stop, packet dump on the associated AP to which the particular mobile station is connected. start - packet dump is started. stop - packet dump is stopped. none- information about current session is not available to the controller." ::= { ciscoLwappPacketDumpInfo 12 } -- ******************************************************************** -- * AP Radio Ssid Stats -- ******************************************************************* cLApDot11RadioSsidTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApDot11RadioSsidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents Per AP, Per Radio information of Ssid of all the neighbor APs updating the APs Radio." ::= { ciscoLwappApIf 11 } cLApDot11RadioSsidEntry OBJECT-TYPE SYNTAX CLApDot11RadioSsidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains ssid information of Neighbor APs of Per AP Per Radio." INDEX { cLApSysMacAddress, cLApDot11IfType, cLApSsidIndex } ::= { cLApDot11RadioSsidTable 1 } CLApDot11RadioSsidEntry ::= SEQUENCE { cLApSsidIndex Unsigned32, cLApDot11RadioSsidName OCTET STRING } cLApSsidIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the index of the ssid detected by Per AP Per Radio." ::= { cLApDot11RadioSsidEntry 1 } cLApDot11RadioSsidName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the ssid name of the neighbor AP on this access point." ::= { cLApDot11RadioSsidEntry 2 } -- ******************************************************************** -- * AP Cable Modem Stats -- ******************************************************************* cLApCableModemIfStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApCableModemIfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the statistics of cable modem interface per AP when the CM connected to the AP." ::= { ciscoLwappApIf 12 } cLApCableModemIfStatsEntry OBJECT-TYPE SYNTAX CLApCableModemIfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains stats information of cable modem per AP" INDEX { cLApSysMacAddress } ::= { cLApCableModemIfStatsTable 1 } CLApCableModemIfStatsEntry ::= SEQUENCE { cLApCmMacAddress MacAddress, cLApCmApMacAddress MacAddress, cLApCmSwVersion SnmpAdminString, cLApEthernetSpeed SnmpAdminString, cLApEthernetStatus SnmpAdminString, cLApCmStatus SnmpAdminString, cLApCmSerialNumber SnmpAdminString, cLApCmUsChannelStatus SnmpAdminString, cLApCmDsChannelStatus SnmpAdminString, cLApCmMaskBit SnmpAdminString } cLApCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the MAC address of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 1 } cLApCmApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the ethernet MAC address of the AP where the Cable Modem is connected." ::= { cLApCableModemIfStatsEntry 2 } cLApCmSwVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the software version of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 3 } cLApEthernetSpeed OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the ethernet speed of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 4 } cLApEthernetStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the ethernet status of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 5 } cLApCmStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the status of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 6 } cLApCmSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the serial number of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 7 } cLApCmUsChannelStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the upstream channel Status of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 8 } cLApCmDsChannelStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the downstream Channel Status of the Cable Modem that has been connected to the AP." ::= { cLApCableModemIfStatsEntry 9 } cLApCmMaskBit OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the mask bit of the Cable Modem based on the mask value the CM statistics is displayed for the AP." ::= { cLApCableModemIfStatsEntry 10 } -- ******************************************************************** -- * AP Environmental information -- ******************************************************************** cLApEnvInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApEnvInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents information about temperature degree state and orientation of the AP" ::= { ciscoLwappAp 11 } cLApEnvInfoEntry OBJECT-TYPE SYNTAX CLApEnvInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table. An entry is created when AP joins the controller. The entry is removed when the AP lose their association with the controller due to loss of communication with controller or when a AP is reset." INDEX { cLApSysMacAddress } ::= { cLApEnvInfoTable 1 } CLApEnvInfoEntry ::= SEQUENCE { cLApEnvTemperatureDegree SnmpAdminString, cLApEnvTemperatureState INTEGER, cLApEnvOrientation INTEGER, cLApEnvPoeOutStatus INTEGER } cLApEnvTemperatureDegree OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents temperature of the AP in both celcius and fahrenheit." ::= { cLApEnvInfoEntry 1 } cLApEnvTemperatureState OBJECT-TYPE SYNTAX INTEGER { unknown(0), green(1), yellow(2), red(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents temperature state of the AP." ::= { cLApEnvInfoEntry 2 } cLApEnvOrientation OBJECT-TYPE SYNTAX INTEGER { unknown(0), vertical(1), horizontal(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents orientation of the AP." ::= { cLApEnvInfoEntry 3 } cLApEnvPoeOutStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), on(2), off(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents POE out status of the AP." ::= { cLApEnvInfoEntry 4 } -- ******************************************************************** -- * GPS related information -- ******************************************************************** cLApGpsInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApGpsInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents information about location and velocity parameters received from the GPS module on the LWAPP Access Points that have joined the controller." ::= { ciscoLwappAp 12 } cLApGpsInfoEntry OBJECT-TYPE SYNTAX CLApGpsInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table. An entry is created when AP joins the controller. The entry is removed when the AP lose their association with the controller due to loss of communication with controller" INDEX { cLApSysMacAddress } ::= { cLApGpsInfoTable 1 } CLApGpsInfoEntry ::= SEQUENCE { cLApGpsLocationPresent TruthValue, cLApGpsLocationValid TruthValue, cLApGpsLatitude SnmpAdminString, cLApGpsLongitude SnmpAdminString, cLApGpsAltitude SnmpAdminString, cLApGpsCollectionTime TimeStamp } cLApGpsLocationPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether the access point has the GPS module installed or not. A value of 'true' indicates GPS module is present in AP. A value of 'false' indicates GPS module is not present in AP." ::= { cLApGpsInfoEntry 1 } cLApGpsLocationValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether the location information is valid or not. A value of 'true' indicates GPS location is valid. A value of 'false' indicates GPS location is not valid." ::= { cLApGpsInfoEntry 2 } cLApGpsLatitude OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents latitude information in the GPS data received." ::= { cLApGpsInfoEntry 3 } cLApGpsLongitude OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents longitude information in the GPS data received." ::= { cLApGpsInfoEntry 4 } cLApGpsAltitude OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents altitude information in the GPS data received." ::= { cLApGpsInfoEntry 5 } cLApGpsCollectionTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time when GPS data was collected." ::= { cLApGpsInfoEntry 6 } -- ******************************************************************** -- * AP Profile Configuration -- ******************************************************************** cLApProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the information about the Access Point profiles. Access Point profile is a set of configuration which can be different for APs at different site/location. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cLApProfileRowStatus object." ::= { ciscoLwappApProfile 1 } cLApProfileEntry OBJECT-TYPE SYNTAX CLApProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the AP profile configuration which can be applied to set of APs based on the controller configuration. Entries can be added/deleted by explicit management actions by NMS or by user console." INDEX { cLApProfileName } ::= { cLApProfileTable 1 } CLApProfileEntry ::= SEQUENCE { cLApProfileName SnmpAdminString, cLApProfileRowStatus RowStatus, cLApProfileCredentialGlobalUserName SnmpAdminString, cLApProfileCredentialGlobalPassword SnmpAdminString, cLApProfileCredentialGlobalSecret SnmpAdminString, cLApProfileCredentialEnableGlobalCredentials TruthValue, cLApProfileLinkLatencyEnable INTEGER, cLApProfileHaloBleBeaconInterval Unsigned32, cLApProfileFastHbTimerTimeout Unsigned32, cLApProfileFastHbTimerEnabled TruthValue, cLApProfilePrimaryDiscoveryTimeout Unsigned32, cLApProfileBackupPrimaryControllerAddressType InetAddressType, cLApProfileBackupPrimaryControllerAddress InetAddress, cLApProfileBackupPrimaryControllerName SnmpAdminString, cLApProfileBackupSecondaryControllerAddressType InetAddressType, cLApProfileBackupSecondaryControllerAddress InetAddress, cLApProfileBackupSecondaryControllerName SnmpAdminString, cLApProfileBackupTertiaryControllerAddressType InetAddressType, cLApProfileBackupTertiaryControllerAddress InetAddress, cLApProfileBackupTertiaryControllerName SnmpAdminString, cLApProfileTcpMss Unsigned32, cLApProfileRetransmitCount Unsigned32, cLApProfileRetransmitTimeout Unsigned32, cLApProfileOeapDisableLocalAccess TruthValue, cLApProfileLedState TruthValue, cLApProfileRadioInterfaceShutdownEnabled TruthValue, cLApProfileEthernetInterfaceDowntime Unsigned32, cLApProfileMulticastGroupAddressType InetAddressType, cLApProfileMulticastGroupAddress InetAddress, cLApProfileMulticastMode INTEGER, cLApProfilePrimedJoinTimeout Unsigned32, cLApProfilePreferMode INTEGER, cLApProfileApLagEnabled TruthValue, cLApProfile802dot1xAuthenticationEnabled TruthValue, cLApProfile802dot1xSupplicantUsername SnmpAdminString, cLApProfile802dot1xSupplicantPassword SnmpAdminString, cLApProfileEncryptionEnable TruthValue, cLApProfileTelnetEnable TruthValue, cLApProfileSshEnable TruthValue, cLApProfileHyperlocationEnable TruthValue, cLApProfileHyperlocationDetectionThreshold Integer32, cLApProfileHyperlocationResetThreshold Unsigned32, cLApProfileHyperlocationTriggerThreshold Unsigned32, cLApProfileHyperlocationNtpIpAddressType InetAddressType, cLApProfileHyperlocationNtpIpAddress InetAddress, cLApProfileAdjustMss TruthValue, cLApProfileDiscoveryTimeout Unsigned32, cLApProfileHeartBeatTimeout Unsigned32, cLApProfileCdpEnable TruthValue, cLApProfileApPacketCaptureProfile SnmpAdminString, cLApProfileRogueReportInterval Unsigned32, cLApProfileRogueMinimumRssi Integer32, cLApProfileRogueTransientInterval Unsigned32, cLApProfileRogueContainFlexconnect TruthValue, cLApProfileRogueContainAutoRateEnable TruthValue, cLApProfileRogueDetectionEnable TruthValue, cLApProfileReportInterval24ghz Integer32, cLApProfileReportInterval5ghz Integer32, cLApProfileDot1xApSwitchEapAuth INTEGER, cLApProfileDot1xApSwtichLscAuth INTEGER, cLApProfileMeshProfileName SnmpAdminString, cLApProfileUsbStatus TruthValue, cLApProfileVlanTagging TruthValue, cLApProfileApCountryCode SnmpAdminString, cLApProfileExtModuleEnable TruthValue, cLApProfileStatsTimer Unsigned32, cLApProfilePoePreStandardSwitchFlag TruthValue, cLApProfilePoePowerInjectorSelection INTEGER, cLApProfilePoeInjectorSwitchMac MacAddress, cLApProfileHaloBleBeaconAdvertisedPwr Unsigned32, cLApProfileTftpDownGradeAddressType InetAddressType, cLApProfileTftpDownGradeAddress InetAddress, cLApProfileTftpDownGradeFileName SnmpAdminString, cLApProfileCoreDumpType INTEGER, cLApProfileCoreDumpTftpAddressType InetAddressType, cLApProfileCoreDumpTftpAddress InetAddress, cLApProfileCoreDumpCoreFileName SnmpAdminString, cLApProfileBackupFallbackEnabled TruthValue } cLApProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies one instance of an AP Profile on the controller." ::= { cLApProfileEntry 1 } cLApProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the row to be added or deleted in this table." ::= { cLApProfileEntry 2 } cLApProfileCredentialGlobalUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the global username for the APs associated to a particular AP Profile. This user name is used to access the console on the AP." ::= { cLApProfileEntry 3 } cLApProfileCredentialGlobalPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the password corresponding to the user name represented by cLApProfileCredentialGlobalUserName object." ::= { cLApProfileEntry 4 } cLApProfileCredentialGlobalSecret OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the secret key for the APs associated to particular AP profile. This provides read-write access to the console on the AP." ::= { cLApProfileEntry 5 } cLApProfileCredentialEnableGlobalCredentials OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether the global credentials for the APs associated to a particular AP Profile is enabled or disabled. A value of 'true' enables the global username/password to be used for the APs associated to a particular AP Profile. A value of 'false' disables the global credentials and uses the credentials specific for the APs." ::= { cLApProfileEntry 6 } cLApProfileLinkLatencyEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2), data(3), reset(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to the configuration of the Link Latency on the APs associated to a particular AP profile. disable - disables the link latency on the APs associated to a particular AP profile. enable - enables the link latency on the APs associated to a particular AP profile. data - enables data link latency on the APs associated to a particular AP profile. reset - reset the link latency on the APs associated to a particular AP profile." ::= { cLApProfileEntry 7 } cLApProfileHaloBleBeaconInterval OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the time interval between HALO BLE beacon transmissions. This value is common to HALO enabled APs that have joined the controller under the same AP profile." DEFVAL { 1 } ::= { cLApProfileEntry 8 } cLApProfileFastHbTimerTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the timeout value for the Fast Heart Beat timer of all the APs associated to the current AP Profile." ::= { cLApProfileEntry 12 } cLApProfileFastHbTimerEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies if Fast Heart Beat Timer is enabled or not. A value of 'true' indicates that this timer is enabled. A value of 'false' indicates that this timer is disabled." ::= { cLApProfileEntry 13 } cLApProfilePrimaryDiscoveryTimeout OBJECT-TYPE SYNTAX Unsigned32 (30..3000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the timeout value for the primary AP discovery for a given Ap profile." DEFVAL { 120 } ::= { cLApProfileEntry 14 } cLApProfileBackupPrimaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the primary controller's address made available through cLApProfileBackupPrimaryControllerAddress." ::= { cLApProfileEntry 15 } cLApProfileBackupPrimaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the primary controller that the APs in the profile should associate with. The name and address should be provided in the same set request. An address of all zeros will unset the primary controller." ::= { cLApProfileEntry 16 } cLApProfileBackupPrimaryControllerName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the name of the primary controller that the APs in the profile should associate with." ::= { cLApProfileEntry 17 } cLApProfileBackupSecondaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the secondary controller's address made available through cLApProfileBackupSecondaryControllerAddress." ::= { cLApProfileEntry 18 } cLApProfileBackupSecondaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the secondary controller that the APs in the profile should associate with. The name and address should be provided in the same set request. An address of all zeros will unset the secondary controller." ::= { cLApProfileEntry 19 } cLApProfileBackupSecondaryControllerName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the name of the secondary controller that the APs in the profile should associate." ::= { cLApProfileEntry 20 } cLApProfileBackupTertiaryControllerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the tertiary controller's address made available through cLApProfileBackupTertiaryControllerAddress." ::= { cLApProfileEntry 21 } cLApProfileBackupTertiaryControllerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the address of the tertiary controller that the APs in the profile should associate with. The name and address should be provided in the same set request. An address of all zeros will unset the tertiary controller." ::= { cLApProfileEntry 22 } cLApProfileBackupTertiaryControllerName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the name of the tertiary controller that the APs in the profile should associate with" ::= { cLApProfileEntry 23 } cLApProfileTcpMss OBJECT-TYPE SYNTAX Unsigned32 (536..1363) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP TCP MSS value per AP profile. The permissible value are between 536 and 1363. This will also enable the global TCP MSS flag. Any change of value for this object will be reflected to cLApTcpMss" ::= { cLApProfileEntry 25 } cLApProfileRetransmitCount OBJECT-TYPE SYNTAX Unsigned32 (3..8) UNITS "retries" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission count for the control packet for all APs associated to this particular AP profile. This value represents the number of packets retransmitted after which the Access Point falls back to another controller in case of failover." ::= { cLApProfileEntry 26 } cLApProfileRetransmitTimeout OBJECT-TYPE SYNTAX Unsigned32 (2..5) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the retransmission timeout for the control packet for all APs associated to this particular AP profile. This value represents the timeout for each control Packet of all the Access Points, joined to this retransmission, during the fallback of Access Point to another controller in case of failover." ::= { cLApProfileEntry 27 } cLApProfileOeapDisableLocalAccess OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the local access is supported for all the Office Extended Access Points associated to current AP Profile. If set to true, the local SSID and and LAN ports on the OEAP will be disabled." ::= { cLApProfileEntry 28 } cLApProfileLedState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the LED state of all the access points associated to a profile should be enabled or disabled." ::= { cLApProfileEntry 29 } cLApProfileRadioInterfaceShutdownEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows the user to enable or disable radio interface of all the APs associated to current AP Profile. When enabled, AP radio's will be shut down when ethernet link goes down for a duration of time set for cLApProfileEthernetInterfaceDowntime. A value of 'true' indicates the AP radio interface shutdown is enabled. A value of 'false' indicates the AP radio interface shutdown is disabled." ::= { cLApProfileEntry 30 } cLApProfileEthernetInterfaceDowntime OBJECT-TYPE SYNTAX Unsigned32 UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the ethernet interface down time after which the AP radio interface will be shut down for Aps in a profile." ::= { cLApProfileEntry 31 } cLApProfileMulticastGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the AP multicast group address type." ::= { cLApProfileEntry 32 } cLApProfileMulticastGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the IPv6 multicast group address of all the APs associated to current AP Profile." ::= { cLApProfileEntry 33 } cLApProfileMulticastMode OBJECT-TYPE SYNTAX INTEGER { unicast(1), multicast(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the ethernet multicast support of all the APs associated to current AP Profile. unicast - Controller will convert multicast to unicast packet. multicast - Multicast mode is enabled." ::= { cLApProfileEntry 34 } cLApProfilePrimedJoinTimeout OBJECT-TYPE SYNTAX Unsigned32 (0..43200) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the primed timeout for the AP discovery for a given profile." ::= { cLApProfileEntry 35 } cLApProfilePreferMode OBJECT-TYPE SYNTAX INTEGER { unconfig(1), ipv4(2), ipv6(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the capwap tunnel prefer-mode for all APs associated to this particular AP Profile. unconfig - capwap tunnel is not established. ipv4 - capwap tunnel established with ipv4 address. ipv6 - capwap tunnel established with ipv6 address." ::= { cLApProfileEntry 36 } cLApProfileApLagEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the ap-lag capability state of all the APs associated to current AP profile. A value of 'true' indicates the ap-lag capability state is enabled. A value of 'false' indicates the ap-lag capability state is disabled." ::= { cLApProfileEntry 37 } cLApProfile802dot1xAuthenticationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the 802.1x supplicant authentication feature of APs associated to current AP Profile. If configured as True, user can configure 8021.1x authentication between lightweight access points and the switch. The access point acts as an 802.1x supplicant and is authenticated by the switch using EAP-FAST with anonymous PAC provisioning.User can set global authentication settings that all access points inherit as they join the controller. This includes all access points that are currently joined to the controller and any that join in the future. If desired, user can override the global authentication settings and assign unique authentication settings for a specific access point." DEFVAL { false } ::= { cLApProfileEntry 38 } cLApProfile802dot1xSupplicantUsername OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the 802.1x supplicant username that is to be inherited by all the APs associated to current AP Profile." ::= { cLApProfileEntry 39 } cLApProfile802dot1xSupplicantPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the 802.1x supplicant Password that is to be inherited by all the APs associated to current AP Profile. A query on this OID will always return '****'." ::= { cLApProfileEntry 40 } cLApProfileEncryptionEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether encyrption between controller and AP is enabled or not in a profile. Encryption can only be enabled if ESM card in controller is pluged in. A value of 'true' enables encryption between controller and AP. A value of 'false' disables encryption between controller and AP." DEFVAL { false } ::= { cLApProfileEntry 41 } cLApProfileTelnetEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether Telnet session can be established to the APs in a given AP profile. A value of 'true' indicates an Telnet session can be established to the APs in a given AP profile. A value of 'false' indicates an Telnet session cannot be established to the APs in a given AP profile." DEFVAL { false } ::= { cLApProfileEntry 42 } cLApProfileSshEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether SSH session can be established to the APs asscoaited to an AP Profile. A value of 'true' indicates an SSH session can be established to the APs asscoaited to AP an Profile. A value of 'false' indicates an SSH session cannot be established to the APs asscoaited to an AP Profile." DEFVAL { false } ::= { cLApProfileEntry 43 } cLApProfileHyperlocationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the admin status of Hyperlocation. A value of 'true' indicates that Hyperlocation is enabled. A value of 'false' indicates that Hyperlocation is disabled." DEFVAL { false } ::= { cLApProfileEntry 44 } cLApProfileHyperlocationDetectionThreshold OBJECT-TYPE SYNTAX Integer32 (-100..-50) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the value of the Hyperlocation detection threshold expressed in dBm. Valid range is -100 dbm to -50 dbm." DEFVAL { -100 } ::= { cLApProfileEntry 45 } cLApProfileHyperlocationResetThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..99) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the value of the Hyperlocation reset threshold expressed in scan cycles. Valid range is 0 to 99 scan cycles. Its value must always be smaller than the trigger threshold." DEFVAL { 8 } ::= { cLApProfileEntry 46 } cLApProfileHyperlocationTriggerThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the value of the Hyperlocation trigger threshold expressed in scan cycles. Valid range is 1 to 100 scan cycles." DEFVAL { 10 } ::= { cLApProfileEntry 47 } cLApProfileHyperlocationNtpIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the NTP server IP address type configured for Hyperlocation feature." ::= { cLApProfileEntry 48 } cLApProfileHyperlocationNtpIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the NTP server IP address configured for Hyperlocation feature." ::= { cLApProfileEntry 49 } cLApProfileAdjustMss OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "To enable the TCP MSS flag" DEFVAL { false } ::= { cLApProfileEntry 50 } cLApProfileDiscoveryTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the timeout for the AP discovery for a particular AP profile." DEFVAL { 10 } ::= { cLApProfileEntry 51 } cLApProfileHeartBeatTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the Heart beat timeout for the APs in a particular AP profile." DEFVAL { 30 } ::= { cLApProfileEntry 52 } cLApProfileCdpEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies to enable the CDP for all APs associated to particular AP Profile" DEFVAL { false } ::= { cLApProfileEntry 53 } cLApProfileApPacketCaptureProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the AP packet capture profile name mapped to this AP join profile. Access Points in this AP join profile will use the parameters of packet capture profile" ::= { cLApProfileEntry 54 } cLApProfileRogueReportInterval OBJECT-TYPE SYNTAX Unsigned32 (10..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the rogue report interval, which is the interval that monitor mode APs send rogue detection details to the controller. This value is valid only for the current AP Profile." ::= { cLApProfileEntry 55 } cLApProfileRogueMinimumRssi OBJECT-TYPE SYNTAX Integer32 (-128..-70) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the minimum value of RSSI considered for detection of rogues. This value is valid only for the current AP Profile." ::= { cLApProfileEntry 56 } cLApProfileRogueTransientInterval OBJECT-TYPE SYNTAX Unsigned32 (0 | 120..1800) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the rogue transient interval for this AP Profile. A value of '0' specifies that an AP sends rogue detection details to the controller as soon as it detects a rogue. A non-zero value specifies that an AP sends rogue detection details to the controller if it hears the rogue more than once in the specified interval." DEFVAL { 0 } ::= { cLApProfileEntry 57 } cLApProfileRogueContainFlexconnect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether Rogue containment of standalone flexconnect APs is enabled in this AP Profile. A value of 'true' enables rogue containment. A value of 'false' disables rogue containment." DEFVAL { false } ::= { cLApProfileEntry 58 } cLApProfileRogueContainAutoRateEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether Rogue containment auto-rate is enabled in this AP Profile. A value of 'true' enables auto-rate. A value of 'false' disables auto-rate." DEFVAL { false } ::= { cLApProfileEntry 59 } cLApProfileRogueDetectionEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether Rogue Detection is enabled in this AP Profile. A value of 'true' enables Rogue Detection. A value of 'false' disables Rogue Detection. Rogue detection is not supported on sniffer and rogue detector mode APs." DEFVAL { true } ::= { cLApProfileEntry 60 } cLApProfileReportInterval24ghz OBJECT-TYPE SYNTAX Integer32 (5..90) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the interval at which APs connected will send client statitics for 802.11b radio for a particular AP profile." DEFVAL { 90 } ::= { cLApProfileEntry 61 } cLApProfileReportInterval5ghz OBJECT-TYPE SYNTAX Integer32 (5..90) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the interval at which APs connected will send client statitics for 802.11a radio for a particular AP profile" DEFVAL { 90 } ::= { cLApProfileEntry 62 } cLApProfileDot1xApSwitchEapAuth OBJECT-TYPE SYNTAX INTEGER { eapNone(1), eapFast(2), eapTls(3), peap(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Dot1x EAP type in this AP Profile." ::= { cLApProfileEntry 63 } cLApProfileDot1xApSwtichLscAuth OBJECT-TYPE SYNTAX INTEGER { authNone(1), authCapwapDtls(2), authDot1xPort(3), authBoth(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies Dot1x LSC AP Auth type in this AP Profile." ::= { cLApProfileEntry 64 } cLApProfileMeshProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object uniquely identifies a mesh profile in a particular AP profile." ::= { cLApProfileEntry 65 } cLApProfileUsbStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies USB status(enable/disable) to be applied to all APs belonging to this AP join profile." DEFVAL { true } ::= { cLApProfileEntry 66 } cLApProfileVlanTagging OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the Vlan tagging of all the APs associated to current AP Profile should be enabled or disabled." DEFVAL { false } ::= { cLApProfileEntry 67 } cLApProfileApCountryCode OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the AP country code mapped to this AP join profile." ::= { cLApProfileEntry 68 } cLApProfileExtModuleEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether extended module is enabled in this AP Profile. A value of 'true' enables extended module. A value of 'false' disables extended module." ::= { cLApProfileEntry 69 } cLApProfileStatsTimer OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the duration of the stats timer value in seconds." DEFVAL { 180 } ::= { cLApProfileEntry 70 } cLApProfilePoePreStandardSwitchFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the Pre-standard switch state as PoE option. A value of 'true' enables Pre-standard switch. A value of 'false' disables Pre-standard switch." ::= { cLApProfileEntry 71 } cLApProfilePoePowerInjectorSelection OBJECT-TYPE SYNTAX INTEGER { unknown(1), installed(2), override(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Power over Ethernet (PoE) injector state for all the APs associated to current AP profile. A value of '1' represents the state of PoE injector is unknown. A value of '2' represents the state of PoE injector is installed. A value of '3' represents the state of PoE injector is override." ::= { cLApProfileEntry 72 } cLApProfilePoeInjectorSwitchMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the MAC address of the switch port that has a Power injector." ::= { cLApProfileEntry 73 } cLApProfileHaloBleBeaconAdvertisedPwr OBJECT-TYPE SYNTAX Unsigned32 (40..100) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Power for HALO BLE beacon advertisement." DEFVAL { 59 } ::= { cLApProfileEntry 74 } cLApProfileTftpDownGradeAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the TFTP servers address type in use." ::= { cLApProfileEntry 75 } cLApProfileTftpDownGradeAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the TFTP servers IP address." ::= { cLApProfileEntry 76 } cLApProfileTftpDownGradeFileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the AP image downgrade file name on the TFTP server." ::= { cLApProfileEntry 77 } cLApProfileCoreDumpType OBJECT-TYPE SYNTAX INTEGER { uncompress(1), compress(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether coredump is enabled and whether it is in compress or uncompress. A value of '1' represents uncompressed form of core dump file. A value of '2' represents compressed form of core dump file. A value of '3' disables the coredump." ::= { cLApProfileEntry 78 } cLApProfileCoreDumpTftpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the TFTP server address type used for AP core dump transfer." ::= { cLApProfileEntry 79 } cLApProfileCoreDumpTftpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the TFTP server address used for AP core dump transfer." ::= { cLApProfileEntry 80 } cLApProfileCoreDumpCoreFileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents core dump file name on the TFTP server." ::= { cLApProfileEntry 81 } cLApProfileBackupFallbackEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents fallback status of APs asscoaited to an AP Profile. A value of 'true' represents AP fallback enabled. A value of 'false' represents AP fallback disabled." ::= { cLApProfileEntry 82 } -- ********************************************************************* -- * Halo BLE Configuration -- ********************************************************************* cLApProfileHaloBleBeaconTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApProfileHaloBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents an instance of HALO BLE configuration per AP profile. It lists the HALO BLE beacon parameters which are common for HALO enabled APs that have joined the controller under the same AP profile." ::= { ciscoLwappApProfile 2 } cLApProfileHaloBleBeaconEntry OBJECT-TYPE SYNTAX CLApProfileHaloBleBeaconEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains an instance of HALO BLE beacon configuration for a specific AP profile. It lists the HALO BLE beacon ID, UUID, transmission power, and status per beacon for HALO enabled APs of a particular AP profile that have joined the controller" INDEX { cLApProfileName, cLApProfileHaloBleBeaconId } ::= { cLApProfileHaloBleBeaconTable 1 } CLApProfileHaloBleBeaconEntry ::= SEQUENCE { cLApProfileHaloBleBeaconId Unsigned32, cLApProfileHaloBleBeaconUuid SnmpAdminString, cLApProfileHaloBleBeaconTxPower Unsigned32, cLApProfileHaloBleBeaconEnabled TruthValue } cLApProfileHaloBleBeaconId OBJECT-TYPE SYNTAX Unsigned32 (0..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents HALO BLE beacon ID for which BLE configuration to be applied." ::= { cLApProfileHaloBleBeaconEntry 1 } cLApProfileHaloBleBeaconUuid OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents HALO BLE beacon UUID (universally unique identifier) which is a 128-bit value." ::= { cLApProfileHaloBleBeaconEntry 2 } cLApProfileHaloBleBeaconTxPower OBJECT-TYPE SYNTAX Unsigned32 (0..52) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents HALO BLE beacon transmission power. The transmission power is based on the size of the required proximity zone." ::= { cLApProfileHaloBleBeaconEntry 3 } cLApProfileHaloBleBeaconEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the status of HALO BLE beacon. true(1) - enable the HALO BLE beacon, false(2) - disable the HALO BLE beacon." ::= { cLApProfileHaloBleBeaconEntry 4 } -- ********************************************************************* -- * AP Packet Capture Profile Configuration -- ********************************************************************* cLApPacketCaptureProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApPacketCaptureProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the information about the packet capture parameters for the 802.11 LWAPP Access Points. Rows are added to this table whenever, new profiles are added to this controller, and rows are deleted whenever profiles gets deleted from the controller." ::= { ciscoLwappApPacketCapture 1 } cLApPacketCaptureProfileEntry OBJECT-TYPE SYNTAX CLApPacketCaptureProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about the packet capture profile configured on the controller." INDEX { cLApPacketCaptureProfileName } ::= { cLApPacketCaptureProfileTable 1 } CLApPacketCaptureProfileEntry ::= SEQUENCE { cLApPacketCaptureProfileName SnmpAdminString, cLApPacketCaptureProfileRowStatus RowStatus, cLApPacketCaptureProfileBufferSize Unsigned32, cLApPacketCaptureProfileDuration Unsigned32, cLApPacketCaptureProfileTruncation Unsigned32, cLApPacketCaptureProfileFtpServerAddressType InetAddressType, cLApPacketCaptureProfileFtpServerAddress InetAddress, cLApPacketCaptureProfileFtpServerPath SnmpAdminString, cLApPacketCaptureProfileFtpUsername SnmpAdminString, cLApPacketCaptureProfileFtpPassword SnmpAdminString, cLApPacketCaptureProfileClassifierArp TruthValue, cLApPacketCaptureProfileClassifierBroadcast TruthValue, cLApPacketCaptureProfileClassifierControl TruthValue, cLApPacketCaptureProfileClassifierData TruthValue, cLApPacketCaptureProfileClassifierDot1x TruthValue, cLApPacketCaptureProfileClassifierIapp TruthValue, cLApPacketCaptureProfileClassifierIp TruthValue, cLApPacketCaptureProfileClassifierManagement TruthValue, cLApPacketCaptureProfileClassifierMulticast TruthValue, cLApPacketCaptureProfileClassifierTcp TruthValue, cLApPacketCaptureProfileClassifierUdp TruthValue, cLApPacketCaptureProfileClassifierTcpPort InetPortNumber, cLApPacketCaptureProfileClassifierUdpPort InetPortNumber } cLApPacketCaptureProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the profile name for ap packet capture profile. The parameters of packet capture profile are used while capturing packets on the Access Point for the specified wireless client." ::= { cLApPacketCaptureProfileEntry 1 } cLApPacketCaptureProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to add or delete an entry in this table." ::= { cLApPacketCaptureProfileEntry 2 } cLApPacketCaptureProfileBufferSize OBJECT-TYPE SYNTAX Unsigned32 (1024..4096) UNITS "kilobytes" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the size of the buffer Access Point should use to copy the captured packets for client and dump it to the FTP server." DEFVAL { 2048 } ::= { cLApPacketCaptureProfileEntry 3 } cLApPacketCaptureProfileDuration OBJECT-TYPE SYNTAX Unsigned32 (1..60) UNITS "Minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the duration for which the Access Point should capture packets for specified client." DEFVAL { 10 } ::= { cLApPacketCaptureProfileEntry 4 } cLApPacketCaptureProfileTruncation OBJECT-TYPE SYNTAX Unsigned32 (0..1500) UNITS "bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of the packet after truncation while capturing packets on the Access Point. Default value is 0 which indictaes captured packet should contain the full payload length." ::= { cLApPacketCaptureProfileEntry 5 } cLApPacketCaptureProfileFtpServerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of the ftp server IP Address made available through cLApPacketCaptureProfileEntry." ::= { cLApPacketCaptureProfileEntry 6 } cLApPacketCaptureProfileFtpServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the IP Address of the FTP server. Access Point will dump the captured packets to a file in this ftp server." ::= { cLApPacketCaptureProfileEntry 7 } cLApPacketCaptureProfileFtpServerPath OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the directory path in the ftp server for storing the file which contains the captured packets in the Access Point." ::= { cLApPacketCaptureProfileEntry 8 } cLApPacketCaptureProfileFtpUsername OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the username to login into the ftp server in order to transfer the captured packets from the Access Point." ::= { cLApPacketCaptureProfileEntry 9 } cLApPacketCaptureProfileFtpPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the password to login into the ftp server in order to transfer the captured packets from the Access Point." ::= { cLApPacketCaptureProfileEntry 10 } cLApPacketCaptureProfileClassifierArp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for ARP packets while capturing packets on the Access Point. A value of 'true' indicates ARP packets should be captured. A value of 'false' indicates ARP packets shouldn't be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 11 } cLApPacketCaptureProfileClassifierBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 Broadcast packets, while capturing packets on the Access Point. A value of 'true' indicates Broadcast packets should be captured. A value of 'false' indicates Broadcast packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 12 } cLApPacketCaptureProfileClassifierControl OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 control packets, while capturing packets on the Access Point under AP Profile which is making use of this packet capture profile. A value of 'true' indicates 802.11 control packets should be captured. A value of 'false' indicates 802.11 control packets should not be captured." DEFVAL { true } ::= { cLApPacketCaptureProfileEntry 13 } cLApPacketCaptureProfileClassifierData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 Data packets, while capturing packets on the Access Point under AP Profile which is making use of this packet capture profile. A value of 'true' indicates 802.11 Data packets should be captured. A value of 'false' indicates 802.11 Data packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 14 } cLApPacketCaptureProfileClassifierDot1x OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 Dot1x packets, while capturing packets on the Access Point under AP Profile which is making use of this packet capture profile. A value of 'true' indicates 802.11 Dot1x packets should be captured. A value of 'false' indicates 802.11 Dot1x packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 15 } cLApPacketCaptureProfileClassifierIapp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 IAPP packets, while capturing packets on the Access Point under AP Profile which is making use of this packet capture profile. A value of 'true' indicates IAPP packets should be captured. A value of 'false' indicates IAPP packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 16 } cLApPacketCaptureProfileClassifierIp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for IP packets, while capturing packets on the Access Point. A value of 'true' indicates IP packets should be captured. A value of 'false' indicates IP packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 17 } cLApPacketCaptureProfileClassifierManagement OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 Management packets, while capturing packets on the Access Point. A value of 'true' indicates 802.11 Management packets should be captured. A value of 'false' indicates 802.11 Management packets should not be captured." DEFVAL { true } ::= { cLApPacketCaptureProfileEntry 18 } cLApPacketCaptureProfileClassifierMulticast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for 802.11 Multicast packets, while capturing packets on the Access Point. A value of 'true' indicates Multicast packets should be captured. A value of 'false' indicates Multicast packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 19 } cLApPacketCaptureProfileClassifierTcp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for TCP packets, while capturing packets on the Access Point. Value of 'true' indicates IP packets should be captured. Value of 'false' indicates IP packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 20 } cLApPacketCaptureProfileClassifierUdp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filters for TCP packets, while capturing packets on the Access Point. Value of 'true' indicates IP packets should be captured. Value of 'false' indicates IP packets should not be captured." DEFVAL { false } ::= { cLApPacketCaptureProfileEntry 21 } cLApPacketCaptureProfileClassifierTcpPort OBJECT-TYPE SYNTAX InetPortNumber (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filter value port number for TCP packets, while capturing packets on the Access Point. Default value is 0 which indicates all TCP packets should be captured." DEFVAL { 0 } ::= { cLApPacketCaptureProfileEntry 22 } cLApPacketCaptureProfileClassifierUdpPort OBJECT-TYPE SYNTAX InetPortNumber (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the filter value port number for UDP packets, while capturing packets on the Access Point under AP Profile which is making use of this packet capture profile. Default value is 0 which indicates all UDP packets should be captured." DEFVAL { 0 } ::= { cLApPacketCaptureProfileEntry 23 } -- ********************************************************************* -- * AP Packet Capture Client Table -- ********************************************************************* cLApPacketCaptureClientTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApPacketCaptureClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information about the status of packet capture already in progress on per Client basis. Rows are added to this table whenever, packet capture is started for a new client, and rows are deleted whenever packet capture gets stopped for a particular Client." ::= { ciscoLwappApPacketCapture 2 } cLApPacketCaptureClientEntry OBJECT-TYPE SYNTAX CLApPacketCaptureClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about packet capture session currently going on for a client on 802.11 LWAPP Access Point that has joined the controller." INDEX { cLApPacketCaptureClientDeviceMac } ::= { cLApPacketCaptureClientTable 1 } CLApPacketCaptureClientEntry ::= SEQUENCE { cLApPacketCaptureClientDeviceMac MacAddress, cLApPacketCaptureClientApMacAddress MacAddress, cLApPacketCaptureClientAutoMode TruthValue, cLApPacketCaptureClientStartStop INTEGER, cLApPacketCaptureClientSiteName SnmpAdminString, cLApPacketCaptureClientRowStatus RowStatus } cLApPacketCaptureClientDeviceMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the mac address of the client for which packet capture should be started on the Access Point. Access Point will check for this mac address while capturing packets." ::= { cLApPacketCaptureClientEntry 1 } cLApPacketCaptureClientApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the base radio mac address of the Access Point on which packet capture should be started. This will be used only in case of static mode but, it is mandatory to populate this in static mode as well." ::= { cLApPacketCaptureClientEntry 2 } cLApPacketCaptureClientAutoMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the mode for packet capture. A value of 'true' indicates packet capture should be started in auto mode, which means capture will be started on the Access Point on which device is currently connected and also on the nearby Access Points which appear in the RRM neighbor lists of present Access Point. A value of 'false' indicates packet capture should be started only on the specified Access Point." ::= { cLApPacketCaptureClientEntry 3 } cLApPacketCaptureClientStartStop OBJECT-TYPE SYNTAX INTEGER { idle(1), start(2), stop(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the trigger to start or stop packet capture for the client. A value of '1' indicates packet capture should be started. A value of '2' indicates packet capture should be stopped." ::= { cLApPacketCaptureClientEntry 4 } cLApPacketCaptureClientSiteName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the site on which the specific device or the Access Point is present." ::= { cLApPacketCaptureClientEntry 5 } cLApPacketCaptureClientRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This oject specifies to the addition or deletion of an entry in this table. When an entry is added, packet capture will be started for the specified device. When an entry is deleted, packet capture will be stopped for the specified device." ::= { cLApPacketCaptureClientEntry 6 } -- ********************************************************************* -- * AP Packet Capture AP table -- ********************************************************************* cLApPacketCaptureApTable OBJECT-TYPE SYNTAX SEQUENCE OF CLApPacketCaptureApEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information about the status of packet capture already in progress on a per AP, per Client basis. Rows are added to this table whenever, packet capture is started for a client on a new AP, and rows are deleted whenever packet capture gets stopped on a particular AP." ::= { ciscoLwappApPacketCapture 3 } cLApPacketCaptureApEntry OBJECT-TYPE SYNTAX CLApPacketCaptureApEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides information about status of packet capture already in progress on the specific AP." INDEX { cLApSysMacAddress } ::= { cLApPacketCaptureApTable 1 } CLApPacketCaptureApEntry ::= SEQUENCE { cLApPacketCaptureApDeviceMac MacAddress, cLApPacketCaptureApMacAddress MacAddress, cLApPacketCaptureApStatus TruthValue } cLApPacketCaptureApDeviceMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the mac address of the device for which packet capture was started on the Access Point. Access Point will check for this mac address while capturing packets." ::= { cLApPacketCaptureApEntry 1 } cLApPacketCaptureApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the base radio mac address of the Access Point on which packet capture was started for the specific device." ::= { cLApPacketCaptureApEntry 2 } cLApPacketCaptureApStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the status of the packet capture. A value of 'true' indicates packet capture has been started for the specified device on the specific Access Point, A value of 'false' indicates packet capture is not started for the specified device on the specific Access Point." ::= { cLApPacketCaptureApEntry 3 } -- ******************************************************************** -- * Notification Objects -- ******************************************************************** cLApAssocFailureReason OBJECT-TYPE SYNTAX CLApAssocFailureReason MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the failure reasons when a AP fails to associate with a controller." ::= { ciscoLwappApMIBNotifObjects 1 } cLApRogueApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the radio MAC address common to the dot11 interfaces of the rogue AP." ::= { ciscoLwappApMIBNotifObjects 2 } cLApDot11RadioChannelNumber OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the channel number of the radio interface of the AP, represented by cLApDot11IfType." ::= { ciscoLwappApMIBNotifObjects 3 } cLApRogueApSsid OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the SSID used by the rogue AP to intrude the network." ::= { ciscoLwappApMIBNotifObjects 4 } cLApRogueType OBJECT-TYPE SYNTAX INTEGER { asleap(1), honeypot(2), other(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the SSID of the used by the rogue AP to intrude the network." ::= { ciscoLwappApMIBNotifObjects 5 } cLApWipsReason OBJECT-TYPE SYNTAX INTEGER { noMonitoringDevice(1) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the failure reasons for an AP when cLApWipsEnable is set to 'true'. noMonitoringDevice - No monitoring device connected to collect WIPs information." ::= { ciscoLwappApMIBNotifObjects 6 } cLApWipsClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies whether this event is raise or clear. A value of 'true' indicates this event is cleared A value of 'false' indicates this even is raised." ::= { ciscoLwappApMIBNotifObjects 7 } cLApIfUpDownFailureType OBJECT-TYPE SYNTAX INTEGER { detectedFailure(1), configuredReset(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the type of the AP interface failure. detectedFailure(1) - Failure of radio. configuredReset(2) - Reset due to manual configuration." ::= { ciscoLwappApMIBNotifObjects 8 } cLApIfUpDownCause OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the cause of the AP interface failure." ::= { ciscoLwappApMIBNotifObjects 9 } cLApIfUpDownFailureCode OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the code of the AP interface failure." ::= { ciscoLwappApMIBNotifObjects 10 } cLApAlarmSet OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies whether this event is raise or clear. A value of 'true' indicates this event is set. A value of 'false' indicates this even is cleared." ::= { ciscoLwappApMIBNotifObjects 11 } cLApRogueClassType OBJECT-TYPE SYNTAX INTEGER { pending(0), friendly(1), malicious(2), unclassified(3), custom(4) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the AP class type of the Rogue AP detected." ::= { ciscoLwappApMIBNotifObjects 12 } cLApRogueDetectedChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the rogue detected channel number." ::= { ciscoLwappApMIBNotifObjects 13 } cLApRSSI OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the Rogue RSSI as seen by AP Interface." ::= { ciscoLwappApMIBNotifObjects 14 } cLApSNR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the SNR seen by AP Interface from Rogue" ::= { ciscoLwappApMIBNotifObjects 15 } cLApDot11RadioCurrentChannel OBJECT-TYPE SYNTAX CLDot11Channel MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the dot11 current channel." ::= { ciscoLwappApMIBNotifObjects 16 } cLApAdhocRogue OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the flag used to state if the rogue found is an Adhoc rogue or it is an AP." ::= { ciscoLwappApMIBNotifObjects 17 } cLApRogueAPOnWiredNetwork OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the flag used to state if the rogue is found on the wired network. A value of '1' indicates Rogue AP is found on wired network. A value of '0' indicates Rogue AP is not found on wired network." ::= { ciscoLwappApMIBNotifObjects 18 } cLApRogueMode OBJECT-TYPE SYNTAX INTEGER { initializing(0), pending(1), alert(2), detectedLrad(3), known(4), acknowledge(5), contained(6), threat(7), containedPending(8), knownContained(9), trustedMissing(10) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP can be a potential threat, trap will be sent out to trap recipients. Known state means its just internal AP which is not on the same Switch. Acknowledge state means an external AP whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing. Threat is usually the state when the rogue is found on wired network. known(4), knownContained(9) and trustedMissing(10) will appear in known rogue list. known rogues can be pre provisioned and known rogues state can be changed to alert(2)." ::= { ciscoLwappApMIBNotifObjects 19 } cLApRogueIsClassifiedByRule OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the flag used to state if the rogue is classified by a rogue rule. A value of 'true' indicates its classifed by rogue rule. A value of 'false' indicates its not classified by rogue rule." ::= { ciscoLwappApMIBNotifObjects 20 } cLApRogueClassifiedApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the radio MAC address of the classified rogue AP." ::= { ciscoLwappApMIBNotifObjects 21 } cLApRogueClassifiedRSSI OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the Rogue classified RSSI as seen by Airespace AP Interface." ::= { ciscoLwappApMIBNotifObjects 22 } cLAPPreviousMonitorMode OBJECT-TYPE SYNTAX CLApMode MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the previous AP monitor Mode." ::= { ciscoLwappApMIBNotifObjects 23 } cLAPCurrentMonitorMode OBJECT-TYPE SYNTAX CLApMode MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the current AP monitor Mode." ::= { ciscoLwappApMIBNotifObjects 24 } cLApSsidKeyConfSsidA OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the SSID which has same cipher key with another SSID on the same AP. The another SSID is represented by cLApSsidKeyConfSsidB." ::= { ciscoLwappApMIBNotifObjects 25 } cLApSsidKeyConfKeyIdxA OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents key index of the SSID which has same cipher key with another SSID on the same AP. It is the key index of cLApSsidKeyConfSsidA. The another SSID is represented by cLApSsidKeyConfSsidB." ::= { ciscoLwappApMIBNotifObjects 26 } cLApSsidKeyConfSsidB OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the SSID which has same cipher key with another SSID on the same AP. The another SSID is represented by cLApSsidKeyConfSsidA." ::= { ciscoLwappApMIBNotifObjects 27 } cLApSsidKeyConfKeyIdxB OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents key index of the SSID which has same cipher key with another SSID on the same AP. It is the key index of cLApSsidKeyConfSsidB. The another SSID is represented by cLApSsidKeyConfSsidA." ::= { ciscoLwappApMIBNotifObjects 28 } cLApPreviousChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the channel before changed." ::= { ciscoLwappApMIBNotifObjects 29 } cLApCurrentChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the channel after changed." ::= { ciscoLwappApMIBNotifObjects 30 } cLApChannelCustomize OBJECT-TYPE SYNTAX INTEGER { automatic(1), customized(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the channel's change mode. If this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only." ::= { ciscoLwappApMIBNotifObjects 31 } cLApIfLoadChannelUtilization OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the code of the AP Interface channel load utilization." ::= { ciscoLwappApMIBNotifObjects 32 } cLAPGroupVlanName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the code of the AP Group Interface Name." ::= { ciscoLwappApMIBNotifObjects 33 } cLApRuleName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the rule name to identify applied on the Ap." ::= { ciscoLwappApMIBNotifObjects 34 } cLApSeverityScore OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object is used to define the custom classification severity score of the rules. This object is applicable when cLRuleRogueType is configured as 'custom'." ::= { ciscoLwappApMIBNotifObjects 35 } cLApDot11XorRadioRoleChangeReason OBJECT-TYPE SYNTAX INTEGER { none(1), auto(2), manual(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object is used to identify the reason code for radio role change of XOR radio." ::= { ciscoLwappApMIBNotifObjects 36 } cLApDot11XorRadioBandChangeReason OBJECT-TYPE SYNTAX INTEGER { none(1), coverageHole(2), hyperlocation(3), revert(4), fra(5), manual(6) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object is used to identify the reason code for radio band change of XOR radio." ::= { ciscoLwappApMIBNotifObjects 37 } -- ******************************************************************** -- * Notifications -- ******************************************************************** ciscoLwappApIfRegulatoryDomainMismatchNotif NOTIFICATION-TYPE OBJECTS { cLApName, cLApDot11IfType, cLApDot11IfRegDomain, cldRegulatoryDomain } STATUS current DESCRIPTION "This notification is generated if an AP radio's regulatory domain doesn't match the country the controller is configured for. Due to the mismatch, the AP will fail to associate with the controller." ::= { ciscoLwappApMIBNotifs 1 } ciscoLwappApCrash NOTIFICATION-TYPE OBJECTS { cLApName } STATUS obsolete DESCRIPTION "This notification is generated after an AP rejoins the controller after a crash. Once the AP joins, the controller will get the crash file from the AP and sends this notification." ::= { ciscoLwappApMIBNotifs 2 } ciscoLwappApUnsupported NOTIFICATION-TYPE OBJECTS { cLApName, cLApAssocFailureReason } STATUS current DESCRIPTION "This notification is generated after an unsupported AP tries to join the controller." ::= { ciscoLwappApMIBNotifs 3 } ciscoLwappApAssociated NOTIFICATION-TYPE OBJECTS { cLApName, cLApLastRebootReason, cLApDataEncryptionStatus } STATUS current DESCRIPTION "This notification is generated whenever an AP joins the controller successfully. This notification contains information about the last reboot reason and Data Encryption status of the AP." ::= { ciscoLwappApMIBNotifs 4 } ciscoLwappApPower NOTIFICATION-TYPE OBJECTS { cLApName, cLApPowerStatus } STATUS current DESCRIPTION "This notification is generated whenever an AP detects low power from Ethernet." ::= { ciscoLwappApMIBNotifs 5 } ciscoLwappApRogueApDetected NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApDot11RadioChannelNumber, cLApRogueApSsid, cLApRogueType } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected." ::= { ciscoLwappApMIBNotifs 6 } ciscoLwappApRogueApCleared NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApDot11RadioChannelNumber, cLApRogueApSsid, cLApRogueType } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP was detected and then subsequently if its been removed from the network." ::= { ciscoLwappApMIBNotifs 7 } ciscoLwappApWipsNotification NOTIFICATION-TYPE OBJECTS { cLApName, cLApWipsReason, cLApWipsClear } STATUS current DESCRIPTION "This notification is generated whenever a controller detects a WIPS event." ::= { ciscoLwappApMIBNotifs 8 } ciscoLwappApNoDownlinkChannelNotify NOTIFICATION-TYPE OBJECTS { cLApName } STATUS current DESCRIPTION "This notification is generated when ever AP fails to find new downlink channel." ::= { ciscoLwappApMIBNotifs 9 } ciscoLwappApIfUpNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApDot11IfSlotId, cLApPortNumber, cLApIfUpDownFailureType, cLApIfUpDownCause, cLApIfUpDownFailureCode, cLApName } STATUS current DESCRIPTION "This notification is generated when AP's Interface operational status goes up." ::= { ciscoLwappApMIBNotifs 10 } ciscoLwappApIfDownNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApDot11IfSlotId, cLApAdminStatus, cLApDot11IfAdminStatus, cLApIfUpDownFailureType, cLApIfUpDownCause, cLApIfUpDownFailureCode, cLApName } STATUS current DESCRIPTION "This notification is generated when AP's Interface operational status goes down." ::= { ciscoLwappApMIBNotifs 11 } ciscoLwappApClientThresholdNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApDot11IfSlotId, cLApDot11IfType, cLRFProfileHighDensityMaxRadioClients, cLRFProfileHDClientTrapThreshold } STATUS current DESCRIPTION "This notification is generated when the number of clients on the AP's Radio Interface exceeds the limit defined in cLRFProfileHDClientTrapThreshold." ::= { ciscoLwappApMIBNotifs 12 } ciscoLwappApUpgradeFailureNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApUpgradeFromVersion, cLApUpgradeToVersion, cLApUpgradeFailureCause } STATUS current DESCRIPTION "This notification is generated when AP image upgrade failed." ::= { ciscoLwappApMIBNotifs 13 } ciscoLwappApCpuUsageHigh NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApCpuCurrentUsage, cLApAlarmSet } STATUS current DESCRIPTION "This notification generates when an AP detects its CPU usage is higher than the threshold configured in clsSysApCpuUsageThreshold, with cLApAlarmSet set to true. When this AP's CPU usage falls below the threshold lately, this notification is generated with cLApAlarmSet set to false." ::= { ciscoLwappApMIBNotifs 14 } ciscoLwappApMemoryUsageHigh NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApMemoryCurrentUsage, cLApAlarmSet } STATUS current DESCRIPTION "This notification generates when an AP detects its memory usage is higher than the threshold configured in clsSysApMemoryUsageThreshold, with cLApAlarmSet set to true. When this AP's memory usage falls below the threshold lately, this notification is generated with cLApAlarmSet set to false." ::= { ciscoLwappApMIBNotifs 15 } ciscoLwappApMaxClientLimitNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApDot11IfSlotId, cLApMaxClientLimitNumberTrap, cLApMaxClientLimitCause, cLApMaxClientLimitSet } STATUS current DESCRIPTION "This notification is generated when the event that max client limit reached is raised or cleared." ::= { ciscoLwappApMIBNotifs 16 } ciscoLwappApAdjChannelRogueDetected NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApRogueDetectedChannel, cLApRSSI, cLApSNR, cLApDot11RadioCurrentChannel, cLApAdhocRogue, cLApRogueApSsid, cLApRogueClassType } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected at the Adjacent channels" ::= { ciscoLwappApMIBNotifs 17 } ciscoLwappApAdjChannelRogueCleared NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApRogueDetectedChannel, cLApDot11RadioCurrentChannel } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected at the Adjacent channels and then subsequently if its been removed from the network." ::= { ciscoLwappApMIBNotifs 18 } ciscoLwappApRogueDetected NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApRogueDetectedChannel, cLApRSSI, cLApSNR, cLApRogueAPOnWiredNetwork, cLApAdhocRogue, cLApRogueApSsid, cLApRogueClassType, cLApRogueMode, cLApRogueIsClassifiedByRule, cLApSeverityScore, cLApRuleName, cLApRogueClassifiedApMacAddress, cLApRogueClassifiedRSSI } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected at the same channel." ::= { ciscoLwappApMIBNotifs 19 } ciscoLwappApCurrentChannelRogueDetected NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApRogueDetectedChannel, cLApRSSI, cLApSNR, cLApDot11RadioCurrentChannel, cLApAdhocRogue, cLApRogueApSsid, cLApRogueClassType } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected at the Current channel." ::= { ciscoLwappApMIBNotifs 20 } ciscoLwappApCurrentChannelRogueCleared NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApRogueApMacAddress, cLApEthernetIfSlotId, cLApDot11IfType, cLApRogueDetectedChannel, cLApDot11RadioCurrentChannel } STATUS current DESCRIPTION "This notification is generated whenever a rogue AP is detected at the Current channels and then subsequently if its been removed from the network." ::= { ciscoLwappApMIBNotifs 21 } ciscoLwappApMonitorModeChangeNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLAPPreviousMonitorMode, cLAPCurrentMonitorMode } STATUS current DESCRIPTION "This notification is generated when the event that AP monitor mode changed." ::= { ciscoLwappApMIBNotifs 22 } ciscoLwappApAcTimeSyncFailureTrap NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName } STATUS current DESCRIPTION "This notification is generated when the heartbeat between AP and Controller is lost or connection broken." ::= { ciscoLwappApMIBNotifs 23 } ciscoLwappApSsidKeyConflict NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApIfMacAddress, cLApSsidKeyConfSsidA, cLApSsidKeyConfKeyIdxA, cLApSsidKeyConfSsidB, cLApSsidKeyConfKeyIdxB } STATUS current DESCRIPTION "This notification is generated whenever 2 SSIDs on same AP have same cipher key." ::= { ciscoLwappApMIBNotifs 24 } ciscoLwappApCurrChannelChanged NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApDot11IfSlotId, cLApPreviousChannel, cLApCurrentChannel, cLApChannelCustomize } STATUS current DESCRIPTION "This notification is generated when the channel is changed by automatic or customized." ::= { ciscoLwappApMIBNotifs 25 } ciscoLwappApCapwapRetransmissionQueueFullEvent NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress } STATUS current DESCRIPTION "This notification is generated whenever capwap retransmission queue for an AP is filled." ::= { ciscoLwappApMIBNotifs 26 } ciscoLwappApSystemBootupEvent NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress } STATUS current DESCRIPTION "This notification is generated whenever AP boots up." ::= { ciscoLwappApMIBNotifs 27 } ciscoLwappXmFilterCheckWarning NOTIFICATION-TYPE OBJECTS { cLApName } STATUS current DESCRIPTION "This notification is generated whenever co-existence filter is not present" ::= { ciscoLwappApMIBNotifs 28 } ciscoLwappApModeUnsupportedOnFlexExpressEvent NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress } STATUS current DESCRIPTION "This notification is generated whenever ap with unsupported mode joins flexexpress wlc or virtual wlc" ::= { ciscoLwappApMIBNotifs 29 } ciscoLwappApXorRadioRoleChangeNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApDot11IfSlotId, cLApDot11XorRadioBand, cLApDot11XorRadioRoleChangeReason } STATUS current DESCRIPTION "This notification is generated whenever XOR radio of AP has changed its Radio role" ::= { ciscoLwappApMIBNotifs 30 } ciscoLwappRadioBandChangeNotify NOTIFICATION-TYPE OBJECTS { cLApSysMacAddress, cLApName, cLApDot11IfSlotId, cLApDot11XorRadioBand, cLApDot11XorRadioBandChangeReason } STATUS current DESCRIPTION "This notification is generated whenever XOR radio of AP has changed its Band" ::= { ciscoLwappApMIBNotifs 31 } -- ******************************************************************** -- * Compliance statements -- ******************************************************************** ciscoLwappApMIBCompliances OBJECT IDENTIFIER ::= { ciscoLwappApMIBConform 1 } ciscoLwappApMIBGroups OBJECT IDENTIFIER ::= { ciscoLwappApMIBConform 2 } -- STATUS deprecated by ciscoLwappApMIBCompliance ciscoLwappApMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup } ::= { ciscoLwappApMIBCompliances 1 } -- STATUS deprecated by ciscoLwappApMIBComplianceRev2 ciscoLwappApMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1 } ::= { ciscoLwappApMIBCompliances 2 } -- STATUS deprecated by ciscoLwappApMIBComplianceRev3 ciscoLwappApMIBComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2 } ::= { ciscoLwappApMIBCompliances 3 } -- Added since last MIB approval ciscoLwappApMIBComplianceRev3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApGroupSup4, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroup, ciscoLwappApGroupSup4, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup } ::= { ciscoLwappApMIBCompliances 4 } -- Added for Franciscan release ciscoLwappApMIBComplianceRev4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroup, ciscoLwappApGroupSup4, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup, ciscoLwappApGroupSup5 } ::= { ciscoLwappApMIBCompliances 5 } ciscoLwappApMIBComplianceRev5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroup, ciscoLwappApGroupSup4, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup, ciscoLwappApGroupSup5, ciscoLwappSeClientSup } ::= { ciscoLwappApMIBCompliances 6 } ciscoLwappApMIBComplianceRev6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroup, ciscoLwappApGroupSup4, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup, ciscoLwappApGroupSup5, ciscoLwappSeClientSup } ::= { ciscoLwappApMIBCompliances 7 } ciscoLwappApMIBComplianceRev7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroupVer1, ciscoLwappApGroupSup6, ciscoLwappApGroupSup7, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup, ciscoLwappApGroupSup5, ciscoLwappSeClientSup, ciscoLwappDot11IfAntennaGroup, ciscoLwappRetransmitGroup, ciscoLwappApNotifsGroupVer2, ciscoLwappApGroupSup8, ciscoLwappApGroupSup9, ciscoLwappApRadioGroupSup1, ciscoLwappHaloBleGroup, ciscoLwappApBleBeaconGroup, ciscoLwappApLanStatsGroup, ciscoLwappApGroupSup10, ciscoLwappApXorRadioGroup, ciscoLwappApNotifsXorGroup } OBJECT cLApDot11IfAntennaEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRetransmitCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRetransmitTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalRetransmitCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalRetransmitTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSecondaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTertiaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEncryptionEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFailoverPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTelnetEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSshEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPreStdStateEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorStateEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorSwMacAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApMonitorModeOptimization MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApDomainName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApNameServerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApAMSDUEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEncryptionSupported MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRogueDetectionEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTcpMss MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp11nChannelBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomFirstChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomSecondChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomThirdChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomFourthChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLegacyBeamForming MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCdpOverAirEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApDot11IfAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEthernetIfAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEthernetIfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalSecret MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLinkLatencyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLinkLatencyReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCountryCode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApIfRegulatoryDomainMismatchNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApCrashEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApUnsupportedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApAssociatedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryDiscoveryTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFastHbTimerTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFastHbTimerEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalFailoverPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalTcpMss MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalDot11IfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalEthernetIfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfNativeVlanId MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSecondaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTertiaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xAuthenticationEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xSupplicantPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xSupplicantUsername MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverrideEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverrideUsername MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverridePassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApNwTxPowerThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialSecret MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialEnableGlobalCredentials MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanListRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoLwappApMIBCompliances 8 } ciscoLwappApMIBComplianceRev8 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappApGroup, ciscoLwappApIfGroup, ciscoLwappApGroupSup1, ciscoLwappApGroupSup2, ciscoLwappApGroupSup3, ciscoLwappApNotifObjsGroup, ciscoLwappApNotifsGroupVer1, ciscoLwappApGroupSup6, ciscoLwappApGroupSup7, ciscoLwappApEthernetIfGroup, ciscoLwappApRadioGroup, ciscoLwappApGroupSup5, ciscoLwappSeClientSup, ciscoLwappDot11IfAntennaGroup, ciscoLwappRetransmitGroup, ciscoLwappApNotifsGroupVer2, ciscoLwappApGroupSup8, ciscoLwappApGroupSup9, ciscoLwappApRadioGroupSup1, ciscoLwappHaloBleGroup, ciscoLwappApBleBeaconGroup, ciscoLwappApLanStatsGroup, ciscoLwappApGroupSup10, ciscoLwappApXorRadioGroup, ciscoLwappApNotifsXorGroup, ciscoLwappApProfileHaloBleGroup, ciscoLwappApProfileGroup, ciscoLwappApPacketCaptureProfileGroup, ciscoLwappApPacketCaptureClientProfileGroup } OBJECT cLApDot11IfAntennaEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRetransmitCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRetransmitTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalRetransmitCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalRetransmitTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSecondaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTertiaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEncryptionEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFailoverPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTelnetEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSshEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPreStdStateEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorStateEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPwrInjectorSwMacAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApMonitorModeOptimization MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApDomainName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApNameServerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApAMSDUEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEncryptionSupported MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApRogueDetectionEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTcpMss MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp11nChannelBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomFirstChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomSecondChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomThirdChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLomFourthChannel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLegacyBeamForming MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCdpOverAirEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApDot11IfAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEthernetIfAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApEthernetIfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialGlobalSecret MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLinkLatencyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApLinkLatencyReset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCountryCode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApIfRegulatoryDomainMismatchNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApCrashEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApUnsupportedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ciscoLwappApAssociatedEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryDiscoveryTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFastHbTimerTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApFastHbTimerEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalPrimaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalSecondaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalFailoverPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalTcpMss MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalDot11IfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobalEthernetIfCdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanIfNativeVlanId MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApPrimaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSecondaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApTertiaryControllerAddressType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xAuthenticationEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xSupplicantPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApGlobal802dot1xSupplicantUsername MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverrideEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverrideUsername MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp802dot1xSupplicantOverridePassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApNwTxPowerThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialSecret MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApCredentialEnableGlobalCredentials MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApVlanListRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLAp11ChannelBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApSecureCipher MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApAntennaBandMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconMajorField MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconMinorField MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconTxPower MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconUuid MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconApplyGlobal MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT cLApBleBeaconAdvTxPower MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoLwappApMIBCompliances 9 } -- ******************************************************************** -- * Units of conformance -- ******************************************************************** ciscoLwappApGroup OBJECT-GROUP OBJECTS { cLApIfMacAddress, cLApMaxNumberOfDot11Slots, cLApIfSmtDot11Bssid } STATUS current DESCRIPTION "This collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 1 } ciscoLwappApIfGroup OBJECT-GROUP OBJECTS { cLApDot11IfType } STATUS current DESCRIPTION "This collection of objects represents the information about the dot11 interfaces of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 2 } ciscoLwappApGroupSup1 OBJECT-GROUP OBJECTS { cLApEntPhysicalIndex } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 3 } ciscoLwappApGroupSup2 OBJECT-GROUP OBJECTS { cLApName } STATUS current DESCRIPTION "This supplemental collection of objects represents the name associated with those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 4 } ciscoLwappApGroupSup3 OBJECT-GROUP OBJECTS { cLApDot11IfRegDomain, cLApDot11nSupport, cLAp11nChannelBandwidth, cLApCountryCode, cLApCountryAllowed } STATUS current DESCRIPTION "This supplemental collection of objects represents the country and 802.11n related information for those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 5 } ciscoLwappApNotifObjsGroup OBJECT-GROUP OBJECTS { cLApAssocFailureReason } STATUS current DESCRIPTION "This supplemental collection of objects represents the information carried by the AP related notifications sent by the agent to a network management station." ::= { ciscoLwappApMIBGroups 6 } ciscoLwappApNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappApIfRegulatoryDomainMismatchNotif, ciscoLwappApUnsupported, ciscoLwappApCrash, ciscoLwappApAssociated } STATUS deprecated DESCRIPTION "This supplemental collection of objects represents the AP related notifications sent by the agent to a network management station. ciscoLwappApNotifsGroup object is superseded by ciscoLwappApNotifsGroupVer1." ::= { ciscoLwappApMIBGroups 7 } ciscoLwappApGroupSup4 OBJECT-GROUP OBJECTS { cLApUpTime, cLLwappUpTime, cLLwappJoinTakenTime, cLApMaxNumberOfEthernetSlots, cLApPrimaryControllerAddressType, cLApPrimaryControllerAddress, cLApSecondaryControllerAddressType, cLApSecondaryControllerAddress, cLApTertiaryControllerAddressType, cLApTertiaryControllerAddress, cLApLomEnabled, cLApLomFirstChannel, cLApLomSecondChannel, cLApLomThirdChannel, cLApLomFourthChannel, cLApCredentialGlobalUserName, cLApCredentialGlobalPassword, cLApCredentialGlobalSecret, cLApCredentialUserName, cLApCredentialPassword, cLApCredentialSecret, cLApCredentialEnableGlobalCredentials, cLApFastHbTimerTimeout, cLApFastHbTimerEnabled, cLApPrimaryDiscoveryTimeout, cLApGlobalPrimaryControllerAddressType, cLApGlobalPrimaryControllerAddress, cLApGlobalPrimaryControllerName, cLApGlobalSecondaryControllerAddressType, cLApGlobalSecondaryControllerAddress, cLApGlobalSecondaryControllerName, ciscoLwappApIfRegulatoryDomainMismatchNotifEnabled, ciscoLwappApCrashEnabled, ciscoLwappApUnsupportedEnabled, ciscoLwappApAssociatedEnabled, cLApLastRebootReason, cLApPrimedDiscoveryTimeout, cLApExtensionChannel, cLAdjChannelRogueEnabled, cLApWipsEnable, cLApNwLegacyBeamForming, cLApProfileFastHbTimerEnabled } STATUS deprecated DESCRIPTION "This supplemental collection of objects represents the information for those APs that have joined the controller. ciscoLwappApGroupSup4 object is superseded by ciscoLwappApGroupSup6." ::= { ciscoLwappApMIBGroups 8 } ciscoLwappApEthernetIfGroup OBJECT-GROUP OBJECTS { cLApEthernetIfName, cLApEthernetIfMacAddress, cLApEthernetIfAdminStatus, cLApEthernetIfOperStatus, cLApEthernetIfRxUcastPkts, cLApEthernetIfRxNUcastPkts, cLApEthernetIfTxUcastPkts, cLApEthernetIfTxNUcastPkts } STATUS current DESCRIPTION "This collection of objects represents the information about the Ethernet interfaces of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 9 } ciscoLwappApRadioGroup OBJECT-GROUP OBJECTS { cLApDot11RadioMACAddress, cLApDot11RadioSubBand, cLApDot11RadioVersion, cLApDot11IsBackhaul, cLApDot11RadioRole, cLApDot11RadioMode, cLApDot11RadioSubType } STATUS current DESCRIPTION "This collection of objects represents the information about the Radios of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 10 } ciscoLwappApGroupSup5 OBJECT-GROUP OBJECTS { cLApGlobalFailoverPriority, cLApFailoverPriority, cLApEncryptionEnable, cLApLinkLatencyEnable, cLApLinkLatencyReset, cLApLinkLatencyStatsCurrent, cLApLinkLatencyStatsMin, cLApLinkLatencyStatsMax, cLApLinkLatencyTimeStamp } STATUS current DESCRIPTION "This supplemental collection of objects represents objects related to encryption and link latency of AP." ::= { ciscoLwappApMIBGroups 11 } ciscoLwappSeClientSup OBJECT-GROUP OBJECTS { cLApSeClientUserName, cLApSeClientIPAddrType, cLApSeClientIPAddr, cLApSeClientDuration, cLApSeClientPort } STATUS current DESCRIPTION "This supplemental collection of objects represents the Spectrum Expert client details connected to the APs." ::= { ciscoLwappApMIBGroups 12 } ciscoLwappDot11IfAntennaGroup OBJECT-GROUP OBJECTS { cLApDot11IfAntennaEnable } STATUS current DESCRIPTION "This supplemental collection of objects represents the antenna details corresponding to the dot11 interface of the Access Points." ::= { ciscoLwappApMIBGroups 13 } ciscoLwappRetransmitGroup OBJECT-GROUP OBJECTS { cLApRetransmitCount, cLApRetransmitTimeout, cLApGlobalRetransmitCount, cLApGlobalRetransmitTimeout } STATUS current DESCRIPTION "This supplemental collection of objects represents the retransmit parameters corresponding to the fallback of an AccessPoint to another controller during failover." ::= { ciscoLwappApMIBGroups 14 } ciscoLwappApGroupSup6 OBJECT-GROUP OBJECTS { cLApUpTime, cLLwappUpTime, cLLwappJoinTakenTime, cLApMaxNumberOfEthernetSlots, cLApPrimaryControllerAddressType, cLApPrimaryControllerAddress, cLApSecondaryControllerAddressType, cLApSecondaryControllerAddress, cLApTertiaryControllerAddressType, cLApTertiaryControllerAddress, cLApLomFirstChannel, cLApLomSecondChannel, cLApLomThirdChannel, cLApLomFourthChannel, cLApCredentialGlobalUserName, cLApCredentialGlobalPassword, cLApCredentialGlobalSecret, cLApCredentialUserName, cLApCredentialPassword, cLApCredentialSecret, cLApCredentialEnableGlobalCredentials, cLApFastHbTimerTimeout, cLApFastHbTimerEnabled, cLApPrimaryDiscoveryTimeout, cLApGlobalPrimaryControllerAddressType, cLApGlobalPrimaryControllerAddress, cLApGlobalPrimaryControllerName, cLApGlobalSecondaryControllerAddressType, cLApGlobalSecondaryControllerAddress, cLApGlobalSecondaryControllerName, ciscoLwappApIfRegulatoryDomainMismatchNotifEnabled, ciscoLwappApCrashEnabled, ciscoLwappApUnsupportedEnabled, ciscoLwappApAssociatedEnabled, cLApLastRebootReason, cLApPrimedDiscoveryTimeout, cLApGlobalPreferMode } STATUS current DESCRIPTION "This supplemental collection of objects represents the global and credential information for those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 15 } ciscoLwappApNotifsGroupVer1 NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappApIfRegulatoryDomainMismatchNotif, ciscoLwappApUnsupported, ciscoLwappApAssociated } STATUS current DESCRIPTION "This supplemental collection of objects represents the AP related notifications sent by the agent to a network management station." ::= { ciscoLwappApMIBGroups 16 } ciscoLwappApGroupSup7 OBJECT-GROUP OBJECTS { cLApTelnetEnable, cLApSshEnable, cLApPreStdStateEnabled, cLApPwrInjectorStateEnabled, cLApPwrInjectorSelection, cLApPwrInjectorSwMacAddr, cLApMonitorModeOptimization, cLApDomainName, cLApNameServerAddress, cLApAMSDUEnable, cLApEncryptionSupported, cLApRogueDetectionEnabled, cLApTcpMss, cLApAdminStatus, cLApCdpOverAirEnabled, cLApDot11IfAdminStatus, cLApEthernetIfCdpEnabled, cLApGlobalTcpMss, cLApGlobalDot11IfCdpEnabled, cLApGlobalEthernetIfCdpEnabled, cLApVlanIfMode, cLApVlanIfEnable, cLApVlanIfNativeVlanId, cLApGlobal802dot1xAuthenticationEnabled, cLApGlobal802dot1xSupplicantPassword, cLApGlobal802dot1xSupplicantUsername, cLApGlobal802dot1xSupplicantEapType, cLAp802dot1xSupplicantOverrideEnabled, cLAp802dot1xSupplicantOverrideUsername, cLAp802dot1xSupplicantOverridePassword, cLAp802dot1xSupplicantOverrideEapType, cLApNwTxPowerThreshold, cLApVlanListRowStatus } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 17 } ciscoLwappApGroupSup8 OBJECT-GROUP OBJECTS { cLApDot11acSupport, cLAp11ChannelBandwidth, cLApExtensionChannels, cLApGlobalMaxApsSupported, cLApAuthorizeApMacAuth, cLApAuthorizeApSerialNumAuth, cLApAuthorizeApMethodList } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 18 } ciscoLwappApNotifsGroupVer2 NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappApPower, ciscoLwappApRogueApDetected, ciscoLwappApRogueApCleared, ciscoLwappApWipsNotification, ciscoLwappApNoDownlinkChannelNotify, ciscoLwappApIfUpNotify, ciscoLwappApIfDownNotify, ciscoLwappRadioBandChangeNotify, ciscoLwappApModeUnsupportedOnFlexExpressEvent, ciscoLwappXmFilterCheckWarning, ciscoLwappApSystemBootupEvent, ciscoLwappApCapwapRetransmissionQueueFullEvent, ciscoLwappApCurrChannelChanged, ciscoLwappApSsidKeyConflict, ciscoLwappApAcTimeSyncFailureTrap, ciscoLwappApMonitorModeChangeNotify, ciscoLwappApCurrentChannelRogueCleared, ciscoLwappApCurrentChannelRogueDetected, ciscoLwappApRogueDetected, ciscoLwappApAdjChannelRogueCleared, ciscoLwappApAdjChannelRogueDetected, ciscoLwappApMaxClientLimitNotify, ciscoLwappApMemoryUsageHigh, ciscoLwappApCpuUsageHigh, ciscoLwappApUpgradeFailureNotify, ciscoLwappApClientThresholdNotify } STATUS current DESCRIPTION "This supplemental collection of objects represents the AP related notifications sent by the agent to a network management station." ::= { ciscoLwappApMIBGroups 19 } ciscoLwappApGroupSup9 OBJECT-GROUP OBJECTS { cLApSecureCipher, cLApAntennaBandMode } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 20 } ciscoLwappApRadioGroupSup1 OBJECT-GROUP OBJECTS { cLApDot11RadioMode, cLApDot11RadioSubType } STATUS current DESCRIPTION "This collection of objects represents the information about the Radios of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 21 } ciscoLwappHaloBleGroup OBJECT-GROUP OBJECTS { cLHaloGlobalBleBeaconInterval, cLHaloGlobalBleBeaconUuid, cLHaloGlobalBleBeaconTxPower, cLHaloGlobalBleBeaconEnable } STATUS current DESCRIPTION "This collection contains BLE global configuration which lists the BLE beacon's identification number and attenuation value of HALO APs that have joined the controller." ::= { ciscoLwappApMIBGroups 22 } ciscoLwappApBleBeaconGroup OBJECT-GROUP OBJECTS { cLApBleBeaconMajorField, cLApBleBeaconMinorField, cLApBleBeaconTxPower, cLApBleBeaconStatus, cLApBleBeaconUuid, cLApBleBeaconInterval, cLApBleBeaconApplyGlobal, cLApBleBeaconAdvTxPower } STATUS current DESCRIPTION "This collection represents BLE beacon's AP specific configuration for HALO APs that have joined the controller." ::= { ciscoLwappApMIBGroups 23 } ciscoLwappApLanStatsGroup OBJECT-GROUP OBJECTS { cLApLanPortState, cLApLanPortVlanId, cLApLanPortVlanIdValid, cLApLanPoeState, cLApLanOverride } STATUS current DESCRIPTION "This collection represents Sardinia AP LAN stats information that have joined the controller." ::= { ciscoLwappApMIBGroups 24 } ciscoLwappApGroupSup10 OBJECT-GROUP OBJECTS { cLApPowerStatus, cLApNameServerAddressType, cLApDataEncryptionStatus, cLApNsiKey, cLApPortNumber, cLApVenueConfigVenueGroup, cLApVenueConfigVenueType, cLApVenueConfigVenueName, cLApVenueConfigLanguage, cLApLEDState, cLApRealTimeStatsModeEnabled, cLApTrunkVlan, cLApTrunkVlanStatus, cLApLocation, cLApSubMode, cLApAssocCount, cLApAssocFailResourceCount, cLApAssociatedClientCount, cLApMemoryCurrentUsage, cLApMemoryAverageUsage, cLApCpuCurrentUsage, cLApCpuAverageUsage, cLApUpgradeFromVersion, cLApUpgradeToVersion, cLApUpgradeFailureCause, cLApMaxClientLimitNumberTrap, cLApMaxClientLimitCause, cLApMaxClientLimitSet, cLApFloorLabel, cLApConnectCount, cLApReassocSuccCount, cLApReassocFailCount, cLApAssocFailCountByRate, cLApAbnormalOfflineCount, cLApActiveClientCount, cLApAssocFailCountForRssiLow, cLApSysNetId, cLApAssocFailTimes, cLApHeartBeatRspAvgTime, cLApEchoRequestCount, cLApEchoResponseLossCount, cLApModuleInserted, cLApEnableModule, cLApIsUniversal, cLApUniversalPrimeStatus, cLApIsMaster, cLApBleFWDownloadStatus, cLApDot11XorDartConnectorStatus, cLApDot11IfAntennaTxEnable, cLApDot11IfAntennaRxEnable, cLApEthernetIfDuplex, cLApEthernetIfLinkSpeed, cLApEthernetIfPOEPower, cLApEthernetIfRxTotalBytes, cLApEthernetIfTxTotalBytes, cLApEthernetIfInputCrc, cLApEthernetIfInputAborts, cLApEthernetIfInputErrors, cLApEthernetIfInputFrames, cLApEthernetIfInputOverrun, cLApEthernetIfInputDrops, cLApEthernetIfInputResource, cLApEthernetIfUnknownProtocol, cLApEthernetIfRunts, cLApEthernetIfGiants, cLApEthernetIfThrottle, cLApEthernetIfResets, cLApEthernetIfOutputCollision, cLApEthernetIfOutputNoBuffer, cLApEthernetIfOutputResource, cLApEthernetIfOutputUnderrun, cLApEthernetIfOutputErrors, cLApEthernetIfOutputTotalDrops, cLApDataLinkLatencyStatsCurrent, cLApDataLinkLatencyStatsMin, cLApDataLinkLatencyStatsMax, cLApDataLinkLatencyTimeStamp, cLApCtsSxpDefaultPassword, cLApCtsSxpState, cLApCtsSxpMode, cLApCtsSxpListenerMinHoldtime, cLApCtsSxpListenerMaxHoldtime, cLApCtsSxpReconcilePeriod, cLApCtsSxpRetryPeriod, cLApCtsSxpSpeakerHoldTime, cLApCtsSxpSpeakerKeepAlive, cLApCtsInlineTagStatus, cLApCtsSgaclStatus, cLApCtsOverrideStatus, cLApModeClear, cLApSiteTagName, cLApRfTagName, cLApPolicyTagName, cLApTagSource, cLApUsbModuleName, cLApUsbModuleState, cLApUsbModuleProductId, cLApUsbDescription, cLApUsbStateInfo, cLApUsbOverride, cLApUsbSerialNumber, cLApUsbMaxPower, cLApLegacyBeamForming, cLApDot11IfLinkChangeCount, cLApDot11MaxClients, cLApPromiscuousModeDwelling, cLApDot11IfStaKeepingTime, cLApDot11IfLinkSpeed, cLApDot11IfMtu, cLApDot11IfDesc, cLAPDot11IfMinTxPowerStep, cLApDot11IfMaxDataRate, cLApEthernetIfMtu, cLApEthernetIfType, cLApEthernetIfLinkChangeCount, cLApWlanStatsTxPktNum, cLApWlanStatsTxOctetNum, cLApWlanStatsRxPktNum, cLApWlanStatsRxOctetNum, cLApWlanStatsRetransmitNum, cLApWlanStatsAssocClientNum, cLApWlanStatsOnlineUserNum, cLApHyperlocationAdminState, cLApHyperlocationUnsetFlag, cLApOeapDisableLocalAccess, cLApGlobalLEDState, cLApRadioInterfaceShutdownEnabled, cLApEthernetInterfaceDowntime, cLAPMulticastGroupAddressType, cLAPMulticastGroupAddress, cLAPMulticastMode, cLApGlobalAPLagCapability, cLApGlobalAPDtlsVersion, cLApGlobalAPDtlsCipherSuite, cLApWlanInfoMaxClients, cLApRadioWlanSsid, cLApRadioWlanBssid, cLApNwTxPowerThresholdVer2, cLApDot11RadioStatsRxErrorFrameCount, cLApDot11RadioStatsMacMicErrFrameCount, cLApDot11RadioStatsMacDecryptErrFrameCount, cLApDot11RadioStatsRxMgmtFrameCount, cLApDot11RadioStatsRxCtrlFrameCount, cLApDot11RadioStatsRxDataFrameCount, cLApDot11RadioStatsTxMgmtFrameCount, cLApDot11RadioStatsTxCtrlFrameCount, cLApDot11RadioStatsTxDataFrameCount, cLApDot11RadioStatsRxDataPacketCount, cLApDot11RadioStatsTxDataPacketCount, cLApDot11RadioStatsTxDataPacketCount, cLApDot11RadioStatsRetryFrameCount, cLApDot11RadioStatsRetryPacketCount, cLApDot11RadioRssiHighest, cLApDot11RadioRssiLowest, cLApDot11RadioRssiAverage, cLApCrashFileName, cLApCrashFileSize, cLApCrashFileTimeStamp, cLApLEDFlashStatus, cLApLEDFlashDuration, cLApInetAddressType, cLApInetAddress, cLApStaticIpv6AddressEnabled, cLApStaticIpv6InetAddressType, cLApStaticIpv6InetAddress, cLApStaticIpv6PrefixLength, cLApStaticIpv6GatewayInetAddressType, cLApStaticIpv6GatewayInetAddress, cLApStaticIpNetmaskType, cLApStaticIpNetmask, cLApPreferMode, cLApPreferModeApplied, cLApSysMemType, cLApSysMemSize, cLApSysFlashSize, cLApSysCpuType, cLApSysFlashType, cLApDot11RadioRateStatsRxPackets, cLApDot11RadioRateStatsRxBytes, cLApDot11RadioRateStatsTxPackets, cLApDot11RadioRateStatsTxBytes, cLApDot11RadioRateString, cLApPacketDumpFtpServerAddressType, cLApPacketDumpFtpServerAddress, cLApPacketDumpFtpServerPath, cLApPacketDumpFtpUsername, cLApPacketDumpFtpPassword, cLApPacketDumpClassifier, cLApPacketDumpBufferSize, cLApPacketDumpCaptureTime, cLApPacketDumpTruncation, cLApPacketDumpApName, cLApPacketDumpDeviceMacAddress, cLApPacketDumpStartStop, cLApDot11RadioSsidName, cLApCmMacAddress, cLApCmApMacAddress, cLApCmSwVersion, cLApEthernetSpeed, cLApEthernetStatus, cLApCmStatus, cLApCmSerialNumber, cLApCmUsChannelStatus, cLApCmDsChannelStatus, cLApCmMaskBit, cLApEnvTemperatureDegree, cLApEnvTemperatureState, cLApEnvOrientation, cLApEnvPoeOutStatus, cLApGpsLocationPresent, cLApGpsLocationValid, cLApGpsLatitude, cLApGpsLongitude, cLApGpsAltitude, cLApGpsCollectionTime, cLApRogueApMacAddress, cLApDot11RadioChannelNumber, cLApRogueApSsid, cLApRogueType, cLApWipsReason, cLApWipsClear, cLApIfUpDownFailureType, cLApIfUpDownCause, cLApIfUpDownFailureCode, cLApAlarmSet, cLApRogueClassType, cLApRogueDetectedChannel, cLApRSSI, cLApSNR, cLApDot11RadioCurrentChannel, cLApAdhocRogue, cLApRogueAPOnWiredNetwork, cLApRogueMode, cLApRogueIsClassifiedByRule, cLApRogueClassifiedApMacAddress, cLApRogueClassifiedRSSI, cLAPPreviousMonitorMode, cLAPCurrentMonitorMode, cLApSsidKeyConfSsidA, cLApSsidKeyConfKeyIdxA, cLApSsidKeyConfSsidB, cLApSsidKeyConfKeyIdxB, cLApPreviousChannel, cLApCurrentChannel, cLApChannelCustomize, cLApIfLoadChannelUtilization, cLAPGroupVlanName, cLApRuleName, cLApSeverityScore, cLApDot11XorRadioRoleChangeReason, cLApDot11XorRadioBandChangeReason } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 25 } ciscoLwappApXorRadioGroup OBJECT-GROUP OBJECTS { cLApDot11XorRadioMode, cLApDot11XorRadioBand, cLApDot11XorRadioRoleAssignment, ciscoLwappXorRadioRoleChangeEnabled, cLApDot11IfSensorReachability, cLApFraCoverageOverlapFactor, cLApFraSuggestedMode } STATUS current DESCRIPTION "This collection of objects represents the information about the Xor Radios of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 26 } ciscoLwappApNotifsXorGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappApXorRadioRoleChangeNotify } STATUS current DESCRIPTION "This collection of objects represents the XOR radio related notifications sent by the agent to a network management station." ::= { ciscoLwappApMIBGroups 27 } ciscoLwappApGroupSup11 OBJECT-GROUP OBJECTS { cLApDot11axSupport } STATUS current DESCRIPTION "This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller." ::= { ciscoLwappApMIBGroups 28 } ciscoLwappApProfileHaloBleGroup OBJECT-GROUP OBJECTS { cLApProfileHaloBleBeaconInterval, cLApProfileHaloBleBeaconTxPower, cLApProfileHaloBleBeaconEnabled, cLApProfileHaloBleBeaconUuid, cLApProfileHaloBleBeaconTxPower, cLApProfileHaloBleBeaconEnabled, cLApProfileHaloBleBeaconAdvertisedPwr } STATUS current DESCRIPTION "This collection contains HALO BLE beacon configuration for a specific AP profile. It lists the HALO BLE beacon ID, UUID, transmission power, and status per beacon for HALO enabled APs that have joined the controller." ::= { ciscoLwappApMIBGroups 29 } ciscoLwappApProfileGroup OBJECT-GROUP OBJECTS { cLApProfileRowStatus, cLApProfileCredentialGlobalUserName, cLApProfileCredentialGlobalPassword, cLApProfileCredentialGlobalSecret, cLApProfileCredentialEnableGlobalCredentials, cLApProfileLinkLatencyEnable, cLApProfileHaloBleBeaconInterval, cLApProfileFastHbTimerTimeout, cLApProfilePrimaryDiscoveryTimeout, cLApProfileBackupPrimaryControllerAddressType, cLApProfileBackupPrimaryControllerAddress, cLApProfileBackupPrimaryControllerName, cLApProfileBackupSecondaryControllerAddressType, cLApProfileBackupSecondaryControllerAddress, cLApProfileBackupSecondaryControllerName, cLApProfileBackupTertiaryControllerAddressType, cLApProfileBackupTertiaryControllerAddress, cLApProfileBackupTertiaryControllerName, cLApProfileTcpMss, cLApProfileRetransmitCount, cLApProfileRetransmitTimeout, cLApProfileOeapDisableLocalAccess, cLApProfileLedState, cLApProfileRadioInterfaceShutdownEnabled, cLApProfileEthernetInterfaceDowntime, cLApProfileMulticastGroupAddressType, cLApProfileMulticastGroupAddress, cLApProfileMulticastMode, cLApProfilePrimedJoinTimeout, cLApProfilePreferMode, cLApProfileApLagEnabled, cLApProfile802dot1xAuthenticationEnabled, cLApProfile802dot1xSupplicantUsername, cLApProfile802dot1xSupplicantPassword, cLApProfileEncryptionEnable, cLApProfileTelnetEnable, cLApProfileSshEnable, cLApProfileHyperlocationEnable, cLApProfileHyperlocationDetectionThreshold, cLApProfileHyperlocationResetThreshold, cLApProfileHyperlocationTriggerThreshold, cLApProfileHyperlocationNtpIpAddressType, cLApProfileHyperlocationNtpIpAddress, cLApProfileAdjustMss, cLApProfileDiscoveryTimeout, cLApProfileHeartBeatTimeout, cLApProfileCdpEnable, cLApProfileApPacketCaptureProfile, cLApProfileRogueReportInterval, cLApProfileRogueMinimumRssi, cLApProfileRogueTransientInterval, cLApProfileRogueContainFlexconnect, cLApProfileRogueContainAutoRateEnable, cLApProfileRogueDetectionEnable, cLApProfileReportInterval24ghz, cLApProfileReportInterval5ghz, cLApProfileDot1xApSwitchEapAuth, cLApProfileDot1xApSwtichLscAuth, cLApProfileMeshProfileName, cLApProfileUsbStatus, cLApProfileVlanTagging, cLApProfileApCountryCode, cLApProfileExtModuleEnable, cLApProfileStatsTimer, cLApProfilePoePreStandardSwitchFlag, cLApProfilePoePowerInjectorSelection, cLApProfilePoeInjectorSwitchMac, cLApProfileHaloBleBeaconAdvertisedPwr, cLApProfileTftpDownGradeAddressType, cLApProfileTftpDownGradeAddress, cLApProfileTftpDownGradeFileName, cLApProfileCoreDumpType, cLApProfileCoreDumpTftpAddressType, cLApProfileCoreDumpTftpAddress, cLApProfileCoreDumpCoreFileName, cLApProfileBackupFallbackEnabled } STATUS current DESCRIPTION "This collection contains the information about the credentials of the 802.11 LWAPP Access Point that have joined the Controller" ::= { ciscoLwappApMIBGroups 30 } ciscoLwappApPacketCaptureProfileGroup OBJECT-GROUP OBJECTS { cLApPacketCaptureProfileRowStatus, cLApPacketCaptureProfileBufferSize, cLApPacketCaptureProfileDuration, cLApPacketCaptureProfileTruncation, cLApPacketCaptureProfileFtpServerAddressType, cLApPacketCaptureProfileFtpServerAddress, cLApPacketCaptureProfileFtpServerPath, cLApPacketCaptureProfileFtpUsername, cLApPacketCaptureProfileFtpPassword, cLApPacketCaptureProfileClassifierArp, cLApPacketCaptureProfileClassifierBroadcast, cLApPacketCaptureProfileClassifierControl, cLApPacketCaptureProfileClassifierData, cLApPacketCaptureProfileClassifierDot1x, cLApPacketCaptureProfileClassifierIapp, cLApPacketCaptureProfileClassifierIp, cLApPacketCaptureProfileClassifierManagement, cLApPacketCaptureProfileClassifierMulticast, cLApPacketCaptureProfileClassifierTcp, cLApPacketCaptureProfileClassifierUdp, cLApPacketCaptureProfileClassifierTcpPort, cLApPacketCaptureProfileClassifierUdpPort, cLApPacketCaptureApDeviceMac, cLApPacketCaptureApMacAddress, cLApPacketCaptureApStatus } STATUS current DESCRIPTION "This collection contains the information about the packet capture parameters of the 802.11 LWAPP Access Point that have joined the Controller" ::= { ciscoLwappApMIBGroups 31 } ciscoLwappApPacketCaptureClientProfileGroup OBJECT-GROUP OBJECTS { cLApPacketCaptureClientApMacAddress, cLApPacketCaptureClientAutoMode, cLApPacketCaptureClientStartStop, cLApPacketCaptureClientSiteName, cLApPacketCaptureClientRowStatus } STATUS current DESCRIPTION "This collection contains the information about the packet capture parameters for per client basis for LWAPP Access Point that have joined the Controller" ::= { ciscoLwappApMIBGroups 32 } END