CISCOSB-HWENVIROMENT DEFINITIONS ::= BEGIN IMPORTS switch001 FROM CISCOSB-MIB MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString,TruthValue FROM SNMPv2-TC; rlEnv MODULE-IDENTITY LAST-UPDATED "200309210001Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Postal: 170 West Tasman Drive San Jose , CA 95134-1706 USA Website: Cisco Small Business Support Community " DESCRIPTION "The private MIB module definition for environment of CISCOSB devices." REVISION "200309210000Z" DESCRIPTION "Added this MODULE-IDENTITY clause." ::= { switch001 83 } RlEnvMonState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the state of a device being monitored. Valid values are: normal(1): the environment is good, such as low temperature. warning(2): the environment is bad, such as temperature above normal operation range but not too high. critical(3): the environment is very bad, such as temperature much higher than normal operation limit. shutdown(4): the environment is the worst, the system should be shutdown immediately. notPresent(5): the environmental monitor is not present, such as temperature sensors do not exist. notFunctioning(6): the environmental monitor does not function properly, such as a temperature sensor generates a abnormal data like 1000 C. " SYNTAX INTEGER { normal(1), warning(2), critical(3), shutdown(4), notPresent(5), notFunctioning(6), notAvailable(7), backingUp(8), readingFailed(9) } RlEnvMonDirection ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the state of a device being monitored. Valid values are: unKnown(1): if the board not support air flow direction. frontToBack(2): the air flow direction of the fan is front to back. backToFront(3): the air flow direction of the fan is back to front. clockwise(4): the air flow direction of the fan is clock wise unClockwise(5): the air flow direction of the fan is unclock wise insideOutside(6): the air flow direction of the fan is inside outside outsideInside(7): the air flow direction of the fan is outside inside rightToLeft(8): the air flow direction of the fan is from right to left leftToRight(9): the air flow direction of the fan is from left to right " SYNTAX INTEGER { unKnown(1), frontToBack(2), backToFront(3), clockwise(4), unClockwise(5), insideOut(6), outsideIn(7), rightToLeft(8), leftToRight(9) } rlEnvPhysicalDescription OBJECT IDENTIFIER ::= { rlEnv 1 } rlEnvMonFanStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RlEnvMonFanStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of fan status maintained by the environmental monitor." ::= { rlEnvPhysicalDescription 1 } rlEnvMonFanStatusEntry OBJECT-TYPE SYNTAX RlEnvMonFanStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the fan status table, representing the status of the associated fan maintained by the environmental monitor." INDEX { rlEnvMonFanStatusIndex } ::= { rlEnvMonFanStatusTable 1 } RlEnvMonFanStatusEntry ::= SEQUENCE { rlEnvMonFanStatusIndex INTEGER, rlEnvMonFanStatusDescr DisplayString, rlEnvMonFanState RlEnvMonState } rlEnvMonFanStatusIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for the fan being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { rlEnvMonFanStatusEntry 1 } rlEnvMonFanStatusDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Textual description of the fan being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { rlEnvMonFanStatusEntry 2 } rlEnvMonFanState OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the fan being instrumented." ::= { rlEnvMonFanStatusEntry 3 } rlEnvMonSupplyStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RlEnvMonSupplyStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of power supply status maintained by the environmental monitor card." ::= { rlEnvPhysicalDescription 2 } rlEnvMonSupplyStatusEntry OBJECT-TYPE SYNTAX RlEnvMonSupplyStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the power supply status table, representing the status of the associated power supply maintained by the environmental monitor card." INDEX { rlEnvMonSupplyStatusIndex } ::= { rlEnvMonSupplyStatusTable 1 } RlEnvMonSupplyStatusEntry ::= SEQUENCE { rlEnvMonSupplyStatusIndex INTEGER , rlEnvMonSupplyStatusDescr DisplayString, rlEnvMonSupplyState RlEnvMonState, rlEnvMonSupplySource INTEGER, rlEnvMonSupplyFanDirection RlEnvMonDirection } rlEnvMonSupplyStatusIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for the power supply being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { rlEnvMonSupplyStatusEntry 1 } rlEnvMonSupplyStatusDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Textual description of the power supply being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { rlEnvMonSupplyStatusEntry 2 } rlEnvMonSupplyState OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the power supply being instrumented." ::= { rlEnvMonSupplyStatusEntry 3 } rlEnvMonSupplySource OBJECT-TYPE SYNTAX INTEGER { unknown(1), ac(2), dc(3), externalPowerSupply(4), internalRedundant(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The power supply source. unknown - Power supply source unknown ac - AC power supply dc - DC power supply externalPowerSupply - External power supply internalRedundant - Internal redundant power supply " ::= { rlEnvMonSupplyStatusEntry 4 } rlEnvMonSupplyFanDirection OBJECT-TYPE SYNTAX RlEnvMonDirection MAX-ACCESS read-only STATUS current DESCRIPTION "The direction of the power supply's fan." ::= { rlEnvMonSupplyStatusEntry 5 } rlEnvFanData OBJECT IDENTIFIER ::= { rlEnv 5 } rlEnvFanDataTable OBJECT-TYPE SYNTAX SEQUENCE OF RlEnvFanDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each unit in a stack" ::= { rlEnvFanData 1 } rlEnvFanDataEntry OBJECT-TYPE SYNTAX RlEnvFanDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of this table specifies a unit" INDEX { rlEnvFanDataStackUnit } ::= { rlEnvFanDataTable 1 } RlEnvFanDataEntry ::= SEQUENCE { rlEnvFanDataStackUnit INTEGER, rlEnvFanDataTemp INTEGER, rlEnvFanDataSpeed INTEGER, rlEnvFanDataOperLevel INTEGER, rlEnvFanDataAdminLevel INTEGER, rlEnvFanDataDirection RlEnvMonDirection } rlEnvFanDataStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the stack unit" ::= { rlEnvFanDataEntry 1 } rlEnvFanDataTemp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The unit temperature" ::= { rlEnvFanDataEntry 2 } rlEnvFanDataSpeed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Fan speed in RPM" ::= { rlEnvFanDataEntry 3 } rlEnvFanDataOperLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Fan speed operative level" ::= { rlEnvFanDataEntry 4 } rlEnvFanDataAdminLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Configured fan speed level" ::= { rlEnvFanDataEntry 5 } rlEnvFanDataDirection OBJECT-TYPE SYNTAX RlEnvMonDirection MAX-ACCESS read-only STATUS current DESCRIPTION "The direction of the system's fan." ::= { rlEnvFanDataEntry 6 } -- ************ Redundant Fan ************** -- RlEnvRedundantFanStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the status of a redundant fan. Valid values are: Ready(1): fan is ready and not active (all fans are O.K) Active(2): fan is active (one or more fan failed) Failure(3): fan failure " SYNTAX INTEGER { ready(1), active(2), failure(3), notPresent(4) } rlEnvRedundantFanTable OBJECT-TYPE SYNTAX SEQUENCE OF RlEnvRedundantFanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of redundant fan status" ::= { rlEnv 6 } rlEnvRedundantFanEntry OBJECT-TYPE SYNTAX RlEnvRedundantFanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the redundant fan status table, representing the status of the associated fan " INDEX { rlEnvRedundantFanUnitId, rlEnvRedundantFanIndex } ::= { rlEnvRedundantFanTable 1 } RlEnvRedundantFanEntry ::= SEQUENCE { rlEnvRedundantFanUnitId Unsigned32, rlEnvRedundantFanIndex INTEGER, rlEnvRedundantFanStatus RlEnvRedundantFanStatus } rlEnvRedundantFanUnitId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the stack unit" ::= { rlEnvRedundantFanEntry 1 } rlEnvRedundantFanIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The fan index" ::= { rlEnvRedundantFanEntry 2 } rlEnvRedundantFanStatus OBJECT-TYPE SYNTAX RlEnvRedundantFanStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The fan status" ::= { rlEnvRedundantFanEntry 3 } rlEnvRedundantFanSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Defines whether Redundant Fan feature is supported" ::= { rlEnv 7 } END