DPW-ATM-MIB DEFINITIONS ::= BEGIN

      IMPORTS
      MODULE-IDENTITY, OBJECT-TYPE,
      Counter32, Unsigned32, mib-2
            FROM SNMPv2-SMI

      MODULE-COMPLIANCE, OBJECT-GROUP
            FROM SNMPv2-CONF

      TruthValue, RowStatus, RowPointer
            FROM SNMPv2-TC

      PerfCurrentCount, PerfIntervalCount
            FROM PerfHist-TC-MIB

      InterfaceIndex
            FROM IF-MIB

      pwIndex
          FROM PW-STD-MIB                    -- [PWMIB]
                                    -- RFC Editor: Please replace
                                    -- PWMIB with correct RFC

      AtmVpIdentifier, AtmVcIdentifier
            FROM ATM-TC-MIB
      ;


        dpwAtmMIB MODULE-IDENTITY
        LAST-UPDATED "200811200000Z"  -- 20 November 2008 12:00:00 GMT 
        ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3)
                      Working Group"
        CONTACT-INFO
            "Senthilkumar Sathappan
             Postal: 1000 Marconi Drive
                     Warrendale PA 15086
             Tel:    +1-724-742-614

             Email:  senthilkumar.sathappan@marconi.com


             Marichetty Venkatesan
             Postal: 1000 Marconi Drive
                     Warrendale PA 15086
             Tel:    +1-724-742-7058
             Email:  venkatesan.marichetty@marconi.com


             Thomas D. Nadeau
             Postal: Cisco Systems, Inc.
                     250 Apollo Drive
                     Chelmsford, MA 01824
             Tel:    +1-978-497-3051
             Email:  tnadeau@cisco.com

             Orly Nicklass
             Postal: Nokia Siemens Networks
                    3 Hanagar st. Neve Ne'eman
                    Hod-Hasharon, Israel
             Email: orly.nicklass@nsn.com

             Discussion and general questions should be posed to
             the PWE3 Working Group (pwe3@ietf.org)."

        DESCRIPTION
            "This MIB contains managed object definitions for
             Pseudo Wire emulation of ATM over Packet Switched
             Networks (PSN).

             This MIB supplements the PW-STD-MIB module.
             The PW-STD-MIB contains structures and MIB associations
             generic to Pseudo-Wire (PW) emulation. PW-specific
             MIBs (such as this) contain config and stats for specific
             PW types.

             Copyright (C) The IETF Trust (2008).  This version of
             this MIB module is part of RFC XXXX; see the RFC itself for
             full legal notices."
  -- RFC Ed.: replace XXXX with actual RFC number & remove this
  --            note"

        -- Revision history.

        REVISION "200811200000Z"  -- 20 November 2008 12:00:00 GMT 
        DESCRIPTION "Initial version published as RFC XXXX."
  -- RFC Ed.: replace XXXX with actual RFC number & remove this
  --          note"

        ::= { mplsATMPWMIB 1 }
       
     -- RFC Editor: replace YYY with IANA-assigned number & remove this
     -- note. Please see IANA considerations section.


      -- Top-level components of this MIB


      dpwAtmNotifications OBJECT IDENTIFIER 
                                        ::= { dpwAtmMIB 0 }
      dpwAtmObjects       OBJECT IDENTIFIER 
                                        ::= { dpwAtmMIB 1 }

  --Generic ATM PW table for all types of ATM PW connection.

  dpwAtmCfgTable OBJECT-TYPE
      SYNTAX    SEQUENCE OF DpwAtmCfgEntry
      MAX-ACCESS        not-accessible
      STATUS            current
      DESCRIPTION
          "This table specifies generic information for an ATM PW
           to be carried over PSN in any mode."
      ::= { dpwAtmObjects 1 }

      dpwAtmCfgEntry OBJECT-TYPE
      SYNTAX        DpwAtmCfgEntry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
             "This table contains a set of parameters for
           the ATM PW that needs to be adapted and carried
           over PSN. This table is indexed by pwIndex from
           pwTable. An entry is created for every newly pwIndex
           in the pwTable. Unless otherwise specified, all
           read-write objects in this table MAY
           be changed when the PW is defined as not active
           and all RW objects values must persist
           after reboot"
      REFERENCE
        "See [PWMIB] "

      INDEX { pwIndex }
      ::= { dpwAtmCfgTable 1 }

  DpwAtmCfgEntry ::= SEQUENCE {
          dpwAtmCfgMaxCellConcatenation       Unsigned32,
          dpwAtmCfgFarEndMaxCellConcatenation Unsigned32,
          dpwAtmCfgTimeoutMode                INTEGER,
          dpwAtmMaxCellConcatenationTimer     Unsigned32
          }

  dpwAtmCfgMaxCellConcatenation OBJECT-TYPE
       SYNTAX        Unsigned32 (1..29)
       MAX-ACCESS    read-write
       STATUS        current
       DESCRIPTION
           "The maximum number of ATM cells that can be
            concatenated into one PW packet towards PSN.
            In non LDP or other signaling protocol environment,
            this object MAY be changed at anytime, but traffic
            might be interuppted, otherwise, it may be changed
            when PW is not active."
      DEFVAL { 1 }
      ::= { dpwAtmCfgEntry 1 }

  dpwAtmCfgFarEndMaxCellConcatenation OBJECT-TYPE
       SYNTAX        Unsigned32 (1..29)
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           "The maximum number of ATM cells that can be
            concatenated into one PW packet towards PSN as reported by
            the far end. If no LDP in use, the object will either
            return value 0 or allow setting it for calculating
            protocol overhead."
      ::= { dpwAtmCfgEntry 2 }

  dpwAtmCfgTimeoutMode OBJECT-TYPE
       SYNTAX        INTEGER
                          {
                           notApplicable (1),
                           disabled      (2),
                           enabled       (3)
                          }
       MAX-ACCESS    read-write
       STATUS        current
       DESCRIPTION
           "This objects determines whether a packet can be
            transmitted to the PSN based on time out expiration
            for collecting cells or not. The actual handling of the
            time out is implementation specific-as such this object
            may be changed at any time under proper consideration of
            traffic interupption effect."
      DEFVAL { 3 }
      ::= { dpwAtmCfgEntry 3 }

  dpwAtmMaxCellConcatenationTimer OBJECT-TYPE
       SYNTAX        Unsigned32 (300..4095)
       MAX-ACCESS    read-write
       STATUS        current
       DESCRIPTION
            "This timer is used to concatenate the maximum ATM cell 
             packets in the configured timer value. The unit of the 
             timer is in microseconds."
      DEFVAL { 1000 }
      ::= { dpwAtmCfgEntry 4 }


  -- Device capable of implementing N:1, 1:1 and transparent cell
  -- mode assumes to support the N:1 table for all
  -- modes with respective applicable setting.
  -- In such implementation, user can create an entry for either
  -- 1:1 or transparent cell transport modes only
  -- in pwAtmInboundNto1Table. The side effect of such
  -- will be an automatic create of the respective line in the
  -- pwAtmOutboundNto1Table.

  -- ATM PW Outbound Table for N to 1 connection

  dpwAtmOutboundNto1Table OBJECT-TYPE
      SYNTAX    SEQUENCE OF DpwAtmOutboundNto1Entry
      MAX-ACCESS        not-accessible
      STATUS            current
      DESCRIPTION
          "This table specifies the information for an ATM PW to
          be carried over PSN in the outbound direction. Up to
          N entries can be created in this table for every
          entry in the pwTable with a pwType equal to:
          atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
            An entry can be created only when the VP/VC are known.
          A single entry will be created in this table for every
          entry in the pwTable with a pwType equal to
          one of the following: atmCell1to1Vcc(12), or
          atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
          atmAal5SduVcc(2), or atmTransparent(3).
          "
      ::= { dpwAtmObjects 2 }

  dpwAtmOutboundNto1Entry OBJECT-TYPE
      SYNTAX        DpwAtmOutboundNto1Entry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "A row in this table represents an ATM PW that needs to be
           adapted and carried over PSN. This table is indexed by
           pwIndex from pwTable and the ATM interface with VPL/ VCLs.
           In atmTransparent(3), Vpi and VCi will be 0xFFFF
           during set operation.
           Unless otherwise specified, all read-create objects in this
           table MUST NOT be changed after row activation
           and SHOULD remain unchanged after reboot."
      INDEX { pwIndex, dpwAtmOutboundNto1AtmIf ,
                          dpwAtmOutboundNto1Vpi }
      ::= { dpwAtmOutboundNto1Table 1 }

  DpwAtmOutboundNto1Entry ::= SEQUENCE {
        dpwAtmOutboundNto1AtmIf                    InterfaceIndex,
        dpwAtmOutboundNto1Vpi                      AtmVpIdentifier,
        dpwAtmOutboundNto1RowStatus                RowStatus,
        dpwAtmOutboundNto1MappedVpi                INTEGER,
        dpwAtmOutboundNto1OntId                    OCTET STRING 
       }

  dpwAtmOutboundNto1AtmIf OBJECT-TYPE
      SYNTAX        InterfaceIndex
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "The ATM Interface that receives cells from the ATM network."
      ::= { dpwAtmOutboundNto1Entry 1 }

  dpwAtmOutboundNto1Vpi OBJECT-TYPE
      SYNTAX        AtmVpIdentifier
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "VPI value of this ATM PW. In atmTransparent(3),
           Vpi will be the equivalent of 0xFFFF"
      ::= { dpwAtmOutboundNto1Entry 2 }

  dpwAtmOutboundNto1RowStatus OBJECT-TYPE
      SYNTAX        RowStatus
      MAX-ACCESS    read-create
      STATUS        current
      DESCRIPTION
          "This Object is used to create, modify or delete a row in
           this table."
      ::= { dpwAtmOutboundNto1Entry 3 }

  dpwAtmOutboundNto1MappedVpi         OBJECT-TYPE
      SYNTAX        INTEGER
                    {
                      disable (0),
                      enable  (1)
                    } 
      MAX-ACCESS    read-create
      STATUS        current
      DESCRIPTION
          "The egress generated VPI value of this ATM PW. The
          entry is valid for PW type of atmCellNto1Vcc(9),
          atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
          atmCell1to1Vpc(13). In other types, the value will be the
          equivalent of 0xFFFF. Value MAY be changed when the
          PW is defined as not active "
      DEFVAL { 0 }
      ::= { dpwAtmOutboundNto1Entry 4 }

  dpwAtmOutboundNto1OntId OBJECT-TYPE
       SYNTAX        OCTET STRING (SIZE(0..255))
       MAX-ACCESS    read-write
       STATUS        current
       DESCRIPTION
           "This object specifies the identification of an ONT."
      ::= { dpwAtmOutboundNto1Entry 5 }

  -- ATM PW Inbound Table for N to 1 connection

  dpwAtmInboundNto1Table OBJECT-TYPE
      SYNTAX    SEQUENCE OF DpwAtmInboundNto1Entry
      MAX-ACCESS        not-accessible
      STATUS            current
      DESCRIPTION
          "This table specifies the information for an ATM PW to
          be carried over PSN in the Inbound direction. Up to
          N entries can be created in this table for every
          entry in the pwTable with a pwType equal to:
          atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
            An entry can be created only when the VP/VC are known.
          A single entry will be created in this table for every
          entry in the pwTable with a pwType equal to
          one of the following:atmCell1to1Vcc(12), or
          atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
          atmAal5SduVcc(2), or atmTransparent(3)."
      ::= { dpwAtmObjects 3 }

  dpwAtmInboundNto1Entry OBJECT-TYPE
      SYNTAX        DpwAtmInboundNto1Entry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "A row in this table represents an ATM PW that needs to be
           adapted and carried over PSN. This table is indexed by
           pwIndex from pwTable and the ATM interface with VPL/ VCLs.
           In atmTransparent(3), Vpi and VCi will be 0xFFFF
           during set operation.
           Unless otherwise specified, all Read-Creat objects in this
           table MUST NOT be changed after row activation
           and SHOULD remain unchanged after reboot."
      INDEX { pwIndex, dpwAtmInboundNto1AtmIf ,
                          dpwAtmInboundNto1Vpi }
      ::= { dpwAtmInboundNto1Table 1 }

  DpwAtmInboundNto1Entry ::= SEQUENCE {
        dpwAtmInboundNto1AtmIf                InterfaceIndex,
        dpwAtmInboundNto1Vpi                  AtmVpIdentifier,
        dpwAtmInboundNto1RowStatus            RowStatus,
        dpwAtmInboundNto1MappedVpi            INTEGER
      }

  dpwAtmInboundNto1AtmIf OBJECT-TYPE
      SYNTAX        InterfaceIndex
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "The ATM Interface that receives cells from the ATM network."
      ::= { dpwAtmInboundNto1Entry 1 }

  dpwAtmInboundNto1Vpi OBJECT-TYPE
      SYNTAX        AtmVpIdentifier
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "VPI value of this ATM PW. In atmTransparent(3),
           Vpi will be the equivalent of 0xFFFF."
      ::= { dpwAtmInboundNto1Entry 2 }

  dpwAtmInboundNto1RowStatus OBJECT-TYPE
      SYNTAX        RowStatus
      MAX-ACCESS    read-create
      STATUS        current
      DESCRIPTION
          "This Object is used to modify or delete a row in
          this table.  This table is associated with dpwAtmOutboundNto1Table. 
          So a row can be created in this table through dpwAtmOutboundNto1Table"
      ::= { dpwAtmInboundNto1Entry 3 }

  dpwAtmInboundNto1MappedVpi    OBJECT-TYPE
      SYNTAX        INTEGER
                    {
                      disable (0),
                      enable  (1)
                    }
      MAX-ACCESS    read-create
      STATUS        current
      DESCRIPTION
          "The generated VPI value of this ATM PW. The
          entry is valid for PW type of atmCellNto1Vcc(9),
          atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
          atmCell1to1Vpc(13). In other types, the value will be the
          equivalent of 0xFFFF. Value MAY be changed when the
          PW is defined as not active."
      DEFVAL { 0 }
      ::= { dpwAtmInboundNto1Entry 4 }

  -- ATM PW QOS VCI-EXP  Table 

  dpwAtmVciExpTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmVciExpEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table contains the ONT downstream VCI-EXP qos mapping
	 parameters. This  exp value represents the queue-type in 
	exp-queue table"
    ::= { dpwAtmObjects 4 }

  dpwAtmVciExpEntry OBJECT-TYPE
    SYNTAX        DpwAtmVciExpEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created for downstream ont qos."
    INDEX  { dpwAtmOntid, dpwAtmVpi, dpwAtmExpVci }
    ::= { dpwAtmVciExpTable 1 }

  DpwAtmVciExpEntry ::= SEQUENCE {
       dpwAtmOntid        Unsigned32,
       dpwAtmVpi          Unsigned32,
       dpwAtmExpVci       Unsigned32,
       dpwAtmVciExp       Unsigned32,
       dpwAtmExpRowStatus Unsigned32
    }

  dpwAtmOntid OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
         "This object represents the identification of an ONT."
    ::= { dpwAtmVciExpEntry 1 }

  dpwAtmVpi OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object represents the downstream ont qos vpi value."
    ::= { dpwAtmVciExpEntry 2 }

  dpwAtmExpVci OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
	" The  downstream ont qos vci value for corresponding vpi."
    ::= { dpwAtmVciExpEntry 3 }
  
  dpwAtmVciExp OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " The exp value representing exp-queue table for downstream ont qos."
    ::= { dpwAtmVciExpEntry 4 }

  dpwAtmExpRowStatus OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This vci-exp table supports only exp value modification. This object becomes active 
	  with default exp value when vci-qos table entries are created. This Object is
	  for internal use only and not configurable by user. "
    ::= { dpwAtmVciExpEntry 5 }

  
  dpwAtmExpQosTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmExpQosEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table contains the downstream ont qos EXP Queue related parameters."
    ::= { dpwAtmObjects 5 }

  dpwAtmExpQosEntry OBJECT-TYPE
    SYNTAX        DpwAtmExpQosEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created for downstream ont qos with queue-type 
	 for corresponfing exp ."
    INDEX  { dpwAtmOntid, dpwAtmQosExp }
    ::= { dpwAtmExpQosTable 1 }

  DpwAtmExpQosEntry ::= SEQUENCE {
       dpwAtmQosExp               Unsigned32,
       dpwAtmExpQosMode           Unsigned32,
       dpwAtmExpQosPriority       Unsigned32,
       dpwAtmExpQosWeight         Unsigned32,
       dpwAtmExpQosRowStatus      Unsigned32
    }

  dpwAtmQosExp OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies the exp value corresponding to downstream ont qos."
    ::= { dpwAtmExpQosEntry 1 }

  dpwAtmExpQosMode OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This obejct specifies the exp queue-type for downstream ont qos ."
    ::= { dpwAtmExpQosEntry 2 }


  dpwAtmExpQosPriority OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifes the priority for queue-type of strict priority(SP)."
    ::= { dpwAtmExpQosEntry 3 }


  dpwAtmExpQosWeight OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies the weight for queue-type of weighted round robin(WRR)."
    ::= { dpwAtmExpQosEntry 4 }

  dpwAtmExpQosRowStatus OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        "This Object is for internal use only and not configurable by user. This table will
	 have default values unless modified by the user."
    ::= { dpwAtmExpQosEntry 5 }



  dpwAtmVciQosTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmVciQosEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table contains VCI Queue related parameters for upstream ont qos."
    ::= { dpwAtmObjects 6 }

  dpwAtmVciQosEntry OBJECT-TYPE
    SYNTAX        DpwAtmVciQosEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created for upstream ont qos vci-qos."
    INDEX  { dpwAtmOntid, dpwAtmVpi, dpwAtmExpVci }
    ::= { dpwAtmVciQosTable 1 }

 DpwAtmVciQosEntry ::= SEQUENCE {
       dpwAtmVciQosClass               INTEGER,
       dpwAtmVciQosPCR                 Unsigned32,
       dpwAtmVciQosSCR                 Unsigned32,
       dpwAtmVciQosMBS                 Unsigned32,
       dpwAtmVciQosCDVT                Unsigned32,
       dpwAtmVciQosRowStatus           Unsigned32
    }

  dpwAtmVciQosClass OBJECT-TYPE
    SYNTAX        INTEGER
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This objects specifies class type for upstream ont qos vci."
    ::= { dpwAtmVciQosEntry 1 }

  dpwAtmVciQosPCR OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies the peak cell rate for corresponding upstream ont qos.This value
          should be in a multiples of 151 only"
    ::= { dpwAtmVciQosEntry 2 }

  dpwAtmVciQosSCR OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies the substainable cell rate for upstream ont qos.This value 
          should be in a multiples of 151 only"
    ::= { dpwAtmVciQosEntry 3 }


  dpwAtmVciQosMBS OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies maximum burst size of corresponding vci in upstream ont qos."
    ::= { dpwAtmVciQosEntry 4 }


  dpwAtmVciQosCDVT OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This object specifies cell delay variance tolerance corresponds to vci in upstream ont qos."
    ::= { dpwAtmVciQosEntry 5 }

  dpwAtmVciQosRowStatus OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This Object is used to create and delete a row in this table.
	  When the Row status is active, whenever user configures in OLT, ONT is also configured.
          For row creation, user is suggested to configure the qos parameters after configuring rowstatus 
	  to create and wait. Then make the row status active. Creation or deletion of vci-qos table 
	  automatically creates/deletes vci-exp table."
    ::= { dpwAtmVciQosEntry 6 }


  -- The following supplement the counters presented in the
  -- PW generic MIB

  -- ATM PW Performance Current Table.

  dpwAtmPerfCurrentTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmPerfCurrentEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "The current 15 minute interval counts are in
         this table.
         This table provides performance information per ATM PW."
    ::= { dpwAtmObjects 7 }

  dpwAtmPerfCurrentEntry OBJECT-TYPE
    SYNTAX        DpwAtmPerfCurrentEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created by the agent for every
         pwAtmCfgTable entry. After 15 minutes, the contents of this
         table entry are copied to a new entry in the
         pwAtmPerfInterval table and the counts in this entry
         are reset to zero."
    INDEX  { pwIndex }
    ::= { dpwAtmPerfCurrentTable 1 }

  DpwAtmPerfCurrentEntry ::= SEQUENCE {
       dpwAtmPerfCurrentMissingPkts    PerfCurrentCount,
       dpwAtmPerfCurrentPktsReOrder    PerfCurrentCount,
       dpwAtmPerfCurrentPktsMisOrder   PerfCurrentCount,
       dpwAtmPerfCurrentPktsTimeout    PerfCurrentCount,
       dpwAtmPerfCurrentCellsXmit      PerfCurrentCount,
       dpwAtmPerfCurrentCellsDropped   PerfCurrentCount,
       dpwAtmPerfCurrentCellsReceived  PerfCurrentCount,
       dpwAtmPerfCurrentUnknownCells   PerfCurrentCount
    }

  dpwAtmPerfCurrentMissingPkts OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of missing packets (as detected via control word
         sequence number gaps)."
    ::= { dpwAtmPerfCurrentEntry 1 }

  dpwAtmPerfCurrentPktsReOrder OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of sequence (via control
         word sequence number), but successfully re-ordered.
         Note: some implementations may not support this Feature."
    ::= { dpwAtmPerfCurrentEntry 2 }

  dpwAtmPerfCurrentPktsMisOrder OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of order (via control word
         sequence numbers)."
     ::= { dpwAtmPerfCurrentEntry 3 }

  dpwAtmPerfCurrentPktsTimeout OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets transmitted due to timeout expiration
         while attempting to collect cells."
     ::= { dpwAtmPerfCurrentEntry 4 }

  dpwAtmPerfCurrentCellsXmit OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of transmitted cells."
     ::= { dpwAtmPerfCurrentEntry 5 }

  dpwAtmPerfCurrentCellsDropped OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of dropped cells."
     ::= { dpwAtmPerfCurrentEntry 6 }

  dpwAtmPerfCurrentCellsReceived OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of received cells."
     ::= { dpwAtmPerfCurrentEntry 7 }

  dpwAtmPerfCurrentUnknownCells OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of cells received from the PSN with unknown VPI or
        VCI values. This object is relevant only in N:1 mode."
     ::= { dpwAtmPerfCurrentEntry 8 }

  -- End ATM PW Performance Current Interval Table


  -- ATM PW Performance Interval Table.

  dpwAtmPerfIntervalTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmPerfIntervalEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table provides performance information per ATM PW
         similar to the pwAtmPerfCurrentTable above. However,
         these counts represent historical 15 minute intervals.
         Typically, this table will have a maximum of 96 entries
         for a 24 hour period. "
    ::= { dpwAtmObjects 8 }

  dpwAtmPerfIntervalEntry OBJECT-TYPE
    SYNTAX        DpwAtmPerfIntervalEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created by the agent for
         every pwAtmPerfCurrentEntry that is 15 minutes old.
         The contents of the Current entry are copied to the new
         entry here. The Current entry, then resets its counts
         to zero for the next current 15 minute interval. "
    INDEX  { pwIndex, dpwAtmPerfIntervalNumber }
    ::= { dpwAtmPerfIntervalTable 1 }

  DpwAtmPerfIntervalEntry ::= SEQUENCE {
       dpwAtmPerfIntervalNumber         Unsigned32,
       dpwAtmPerfIntervalValidData      TruthValue,
       dpwAtmPerfIntervalDuration       Unsigned32,
       dpwAtmPerfIntervalMissingPkts    PerfIntervalCount,
       dpwAtmPerfIntervalPktsReOrder    PerfIntervalCount,
       dpwAtmPerfIntervalPktsMisOrder   PerfIntervalCount,
       dpwAtmPerfIntervalPktsTimeout    PerfIntervalCount,
       dpwAtmPerfIntervalCellsXmit      PerfIntervalCount,
       dpwAtmPerfIntervalCellsDropped   PerfIntervalCount,
       dpwAtmPerfIntervalCellsReceived  PerfIntervalCount,
       dpwAtmPerfIntervalUnknownCells   PerfIntervalCount,
       dpwAtmPerfIntervalTime           OCTET STRING
       }

  dpwAtmPerfIntervalNumber OBJECT-TYPE
    SYNTAX        Unsigned32 (1..96)
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "A number (normally between 1 and 96 to cover a 24 hour
         period) which identifies the interval for which the set
         of statistics is available. The interval identified by 1
         is the most recently completed 15 minute interval, and
         the interval identified by N is the interval immediately
         preceding the one identified by N-1. The minimum range of
         N is 1 through 4. The default range is 1 through 32. The
         maximum value of N is 96."
    ::= { dpwAtmPerfIntervalEntry 1 }

  dpwAtmPerfIntervalValidData OBJECT-TYPE
    SYNTAX        TruthValue
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "This variable indicates if the data for this interval
         is valid."
    ::= { dpwAtmPerfIntervalEntry 2 }

  dpwAtmPerfIntervalDuration OBJECT-TYPE
     SYNTAX      Unsigned32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The duration of a particular interval in seconds,
        Adjustments in the system's time-of-day clock, may
        cause the interval to be greater or less than, the
        normal value. Therefore this actual interval value
        is provided."
     ::= { dpwAtmPerfIntervalEntry 3 }

  dpwAtmPerfIntervalMissingPkts OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of missing packets (as detected via control
         word sequence number gaps)."
    ::= { dpwAtmPerfIntervalEntry 4 }


  dpwAtmPerfIntervalPktsReOrder OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of sequence (via control
         word sequence number), but successfully re-ordered.
         Note: some implementations may not support this
         Feature."
    ::= { dpwAtmPerfIntervalEntry 5 }

   dpwAtmPerfIntervalPktsMisOrder OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of order (via control word
         sequence numbers)."
    ::= { dpwAtmPerfIntervalEntry 6 }

  dpwAtmPerfIntervalPktsTimeout OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets transmitted due to timeout expiration."
     ::= { dpwAtmPerfIntervalEntry 7 }

  dpwAtmPerfIntervalCellsXmit OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of transmitted cells."
     ::= { dpwAtmPerfIntervalEntry 8 }

  dpwAtmPerfIntervalCellsDropped OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of dropped cells."
     ::= { dpwAtmPerfIntervalEntry 9 }

  dpwAtmPerfIntervalCellsReceived OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of received cells."
     ::= { dpwAtmPerfIntervalEntry 10 }

  dpwAtmPerfIntervalUnknownCells OBJECT-TYPE
    SYNTAX        PerfIntervalCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of cells received from the PSN  with unknown VPI or
        VCI values. This object is relevant only in N:1 mode."
     ::= { dpwAtmPerfIntervalEntry 11 }

  dpwAtmPerfIntervalTime OBJECT-TYPE
    SYNTAX        OCTET STRING
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Timestamp value of the system in hours, minutes and seconds 
         when data is received for particular pseudo-wire for every
         15-minutes"
     ::= { dpwAtmPerfIntervalEntry 12 }    

  -- End ATM PW Performance Interval Table


  -- ATM PW 1day Performance Table


  dpwAtmPerf1DayIntervalTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmPerf1DayIntervalEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table provides performance information per ATM PW
         similar to the pwAtmPerfIntervalTable above. However,
         these counters represent historical 1 day intervals up to
         one full month."
    ::= { dpwAtmObjects 9 }

  dpwAtmPerf1DayIntervalEntry OBJECT-TYPE
    SYNTAX        DpwAtmPerf1DayIntervalEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry is created in this table by the agent
         for every entry in the pwAtmCfgTable table."
    INDEX  { pwIndex,dpwAtmPerf1DayIntervalNumber }
       ::= { dpwAtmPerf1DayIntervalTable 1 }

  DpwAtmPerf1DayIntervalEntry ::= SEQUENCE {
       dpwAtmPerf1DayIntervalNumber          Unsigned32,
       dpwAtmPerf1DayIntervalValidData       TruthValue,
       dpwAtmPerf1DayIntervalDuration        Unsigned32,
       dpwAtmPerf1DayIntervalMissingPkts     Counter32,
       dpwAtmPerf1DayIntervalPktsReOrder     Counter32,
       dpwAtmPerf1DayIntervalPktsMisOrder    Counter32,
       dpwAtmPerf1DayIntervalPktsTimeout     Counter32,
       dpwAtmPerf1DayIntervalCellsXmit       Counter32,
       dpwAtmPerf1DayIntervalCellsDropped    Counter32,
       dpwAtmPerf1DayIntervalCellsReceived   Counter32,
       dpwAtmPerf1DayIntervalUnknownCells    Counter32,
       dpwAtmPerf1DayIntervalTime            OCTET STRING
       }

  dpwAtmPerf1DayIntervalNumber OBJECT-TYPE
    SYNTAX        Unsigned32 (1..365)
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "The number of interval, where 1 indicates current day
         measured period and 2 and above indicate previous days
         respectively"
    ::= { dpwAtmPerf1DayIntervalEntry 1 }

  dpwAtmPerf1DayIntervalValidData OBJECT-TYPE
    SYNTAX        TruthValue
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "This object indicates if the data for this interval
         is valid."
    ::= { dpwAtmPerf1DayIntervalEntry 2 }

  dpwAtmPerf1DayIntervalDuration OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The duration of a particular interval in seconds,
       Adjustments in the system's time-of-day clock, may
       cause the interval to be greater or less than, the
       normal value. Therefore this actual interval value
       is provided."
    ::= { dpwAtmPerf1DayIntervalEntry 3 }

  dpwAtmPerf1DayIntervalMissingPkts OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
      "Number of missing packets (as detected via control word
       sequence number gaps)."
    ::= { dpwAtmPerf1DayIntervalEntry 4 }

  dpwAtmPerf1DayIntervalPktsReOrder OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of sequence (via control
         word sequence number), but successfully re-ordered.
         Note: some implementations may not support this
         feature."
    ::= { dpwAtmPerf1DayIntervalEntry 5 }

  dpwAtmPerf1DayIntervalPktsMisOrder OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets detected out of order(via control word
         sequence numbers), and could not be re-ordered."
    ::= { dpwAtmPerf1DayIntervalEntry 6 }

  dpwAtmPerf1DayIntervalPktsTimeout OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of packets transmitted due to timeout expiration."
     ::= { dpwAtmPerf1DayIntervalEntry 7 }

  dpwAtmPerf1DayIntervalCellsXmit OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of transmitted cells."
     ::= { dpwAtmPerf1DayIntervalEntry 8 }

  dpwAtmPerf1DayIntervalCellsDropped OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of dropped cells."
     ::= { dpwAtmPerf1DayIntervalEntry 9 }

  dpwAtmPerf1DayIntervalCellsReceived OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of received cells."
     ::= { dpwAtmPerf1DayIntervalEntry 10 }

  dpwAtmPerf1DayIntervalUnknownCells OBJECT-TYPE
    SYNTAX        Counter32
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of cells received from the PSN  with unknown VPI
        or VCI value. This object is relevant only in N:1 mode."
     ::= { dpwAtmPerf1DayIntervalEntry 11 }

  dpwAtmPerf1DayIntervalTime OBJECT-TYPE
    SYNTAX        OCTET STRING
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
       "Timestamp value of the system in hours, minutes and seconds
        when data is received for particular pseudo-wire for every
        day" 
     ::= { dpwAtmPerf1DayIntervalEntry 12 }

  -- End of ATM PW Performance table

-- PW OAM Table

  dpwOamTable OBJECT-TYPE
      SYNTAX    SEQUENCE OF DpwOamEntry
      MAX-ACCESS        not-accessible
      STATUS            current
      DESCRIPTION
         "This table specifies to enable/disable OAM 
         on the PW associated to the specified pwIndex.
         It also shows the defects of the PW OAM."
         
      ::= { dpwAtmObjects 10 }

  dpwOamEntry OBJECT-TYPE
      SYNTAX        DpwOamEntry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
         "This table is indexed by pwIndex.
          Unless otherwise specified, all read-create
          objects in this table MUST NOT be changed 
          after row activation and SHOULD remain
          unchanged after reboot."

      INDEX { pwIndex }
      ::= { dpwOamTable 1}

  DpwOamEntry ::= SEQUENCE {
        dpwOamEnable               TruthValue,
        dpwOamDefect               INTEGER,
        dpwOamRowStatus            RowStatus
      }


  dpwOamEnable  OBJECT-TYPE
     SYNTAX        TruthValue
     MAX-ACCESS    read-write
     STATUS        current
     DESCRIPTION
         "This variable indicates if OAM is enabled for this PW. 
          It MAY be changed at any time."
     DEFVAL { true }
     ::= { dpwOamEntry 1 }


  dpwOamDefect OBJECT-TYPE  
      SYNTAX        INTEGER   
      MAX-ACCESS    read-only  
      STATUS        current  
      DESCRIPTION  
           "This specifies the defect states of PW OAM"
      ::= { dpwOamEntry 2 }  
 
  dpwOamRowStatus OBJECT-TYPE  
      SYNTAX        RowStatus  
      MAX-ACCESS    read-create  
      STATUS        current  
      DESCRIPTION  
          "For creating, modifying, and deleting this row. None of the  
           read-create objects in the conceptual rows may be changed   
           when this object is in the active(1) state."  
       ::= { dpwOamEntry 3 } 

  -- End of PW OAM Table

  -- ATMOAM TABLE

  dpwAtmoamTable OBJECT-TYPE
      SYNTAX    SEQUENCE OF DpwAtmoamEntry
      MAX-ACCESS        not-accessible
      STATUS            current
      DESCRIPTION
         "This table specifies to enable/disable CC Generation and also
          to set the Flow Type as E2E / SEG." 
         
      ::= { dpwAtmObjects 11 }

  dpwAtmoamEntry OBJECT-TYPE
      SYNTAX        DpwAtmoamEntry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
         "This table is indexed by pwIndex.
          Unless otherwise specified, all read-create
          objects in this table MUST NOT be changed 
          after row activation and SHOULD remain
          unchanged after reboot."

      INDEX { pwIndex }
      ::= { dpwAtmoamTable 1 }

  DpwAtmoamEntry ::= SEQUENCE {
        dpwCcStatus          TruthValue,
        dpwFlowType          INTEGER,
        dpwAtmoamRowStatus   RowStatus,
		dpwFrequencyTimerIntvl INTEGER
       }


  dpwCcStatus  OBJECT-TYPE  
      SYNTAX        TruthValue
      MAX-ACCESS    read-write  
      STATUS        current  
      DESCRIPTION  
           "This variable is used to enable / disable the CC Status."
      DEFVAL { false }
      ::= { dpwAtmoamEntry 1 } 

  dpwFlowType  OBJECT-TYPE  
      SYNTAX        INTEGER {  
             ete    (1),  
             seg    (2),
             both   (3)   
      }  
      MAX-ACCESS    read-write  
      STATUS        current  
      DESCRIPTION  
           "This variable is used to set the flow type as E2E / SEG / Both."
      DEFVAL { ete } 
      ::= { dpwAtmoamEntry 2 } 
 
  dpwAtmoamRowStatus OBJECT-TYPE  
      SYNTAX        RowStatus  
      MAX-ACCESS    read-create  
      STATUS        current  
      DESCRIPTION  
          "For creating, modifying, and deleting this row. None of the  
           read-create objects in the conceptual rows may be changed   
           when this object is in the active(1) state."  
       ::= { dpwAtmoamEntry 3 } 

  dpwFrequencyTimerIntvl  OBJECT-TYPE
      SYNTAX        TruthValue
      MAX-ACCESS    read-write
      STATUS        current
      DESCRIPTION
           "This variable is used to set the Frequency Timer Interval.
            The frequency timer interval can be 1 or 2"
      DEFVAL { 1 }
      ::= { dpwAtmoamEntry 4 }

  -- End of ATMOAM Table

 -- VP SHAPING Table
 -- jira id DASAN - 84 
  dpwAtmVpShapingTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmVpShapingEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "This table contains VP Shaping related parameters for upstream ont qos."
    ::= { dpwAtmObjects 12 }

  dpwAtmVpShapingEntry OBJECT-TYPE
    SYNTAX        DpwAtmVpShapingEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created for upstream ont qos vci-qos."
    INDEX  { dpwAtmOntid, dpwAtmVpi }
    ::= { dpwAtmVpShapingTable 1 }

 DpwAtmVpShapingEntry ::= SEQUENCE {
       dpwAtmVpShapingBandwidth        Unsigned32,
       dpwAtmVpShapingRowStatus        Unsigned32
    }

  
  dpwAtmVpShapingBandwidth OBJECT-TYPE
       SYNTAX        Unsigned32 (300..358795)
       MAX-ACCESS    read-create
       STATUS        current
       DESCRIPTION
            "The Vp shaping bandwidth for upstream ATM cell packets.
             The unit of bandwidth is in cell/seconds."
       DEFVAL { 10000 }
       ::= { dpwAtmVpShapingEntry 1 }
  
  dpwAtmVpShapingRowStatus OBJECT-TYPE
    SYNTAX        Unsigned32
    MAX-ACCESS    read-create
    STATUS        current
    DESCRIPTION
        " This Object is used to create, modify and delete a row in this table.
	  When the Row status is active, whenever user configures in OLT, ONT is also configured.
          For row creation, user is suggested to configure the bandwidth parameter after setting the
	  row status to create and wait. Then make the row status active."
    ::= { dpwAtmVpShapingEntry 2 }
  
  -- End of VP SHAPING Table

-- ATM OAM Stats Table.

-- JIRAID    : DASAN-664 Implementation of PW OAM Statistics - SNMP support

  dpwAtmOamStatsTable OBJECT-TYPE
    SYNTAX        SEQUENCE OF DpwAtmOamStatsEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "The OAM statistic counts are in
         this table.
         This table provides OAM statistics information per ATM PW."
    ::= { dpwAtmObjects 13 }

  dpwAtmOamStatsEntry OBJECT-TYPE
    SYNTAX        DpwAtmOamStatsEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in this table is created when AIS/RDI cells are received.
         Number of OAM cells Txmitted and received are incremented"
    INDEX  { pwIndex }
    ::= { dpwAtmOamStatsTable 1 }

  DpwAtmOamStatsEntry ::= SEQUENCE {

       dpwAtmOamStatsOamCellsRx    PerfCurrentCount,
       dpwAtmOamStatsOamCellsTx    PerfCurrentCount
    }
  dpwAtmOamStatsOamCellsRx OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of OAM Cells received."
    ::= { dpwAtmOamStatsEntry 1 }

  dpwAtmOamStatsOamCellsTx OBJECT-TYPE
    SYNTAX        PerfCurrentCount
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "Number of OAM Cells transmitted."
    ::= { dpwAtmOamStatsEntry 2 }

-- End of ATM OAM Stats Table.

 END