-- extracted from draft-ietf-idr-bgp4-mibv2-15.txt -- at Wed Jul 4 11:46:02 2018 -- Renumbered to sit underneath Dell's enterprise. -- ***************************************************************** -- DELLEMC-OS10-BGP4V2-MIB -- -- -- Copyright (c) 2018 by Dell Inc. -- All rights reserved. -- ***************************************************************** DELLEMC-OS10-BGP4V2-MIB DEFINITIONS ::= BEGIN -- This module provides authoritative definitions for Dell EMC Networking OS10 -- BGP4V2 MIB. -- -- This module will be extended, as needed. -- IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Gauge32, Unsigned32 FROM SNMPv2-SMI os10Experiment FROM DELLEMC-OS10-SMI-MIB InetAddressType, InetAddress, InetPortNumber, InetAutonomousSystemNumber, InetAddressPrefixLength FROM INET-ADDRESS-MIB TruthValue, RowPointer, TimeStamp, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB; os10Bgp4V2Mib MODULE-IDENTITY LAST-UPDATED "202002251200Z" ORGANIZATION "Dell EMC" CONTACT-INFO "http://www.dell.com/support" DESCRIPTION "The MIB module for the BGP-4 protocol." REVISION "202002251200Z" DESCRIPTION "Changed the MAX-ACCESS of bgp4V2AdjRibsOutIndex to not-accessible." REVISION "201807041200Z" DESCRIPTION "Dell EMC Networking OS10 Experiment object IDs added." REVISION "201401240000Z" DESCRIPTION "This MIB updates and replaces the BGP MIB defined in RFC 4273." ::= { os10Experiment 1 } Os10Bgp4V2IdentifierTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "1d." STATUS current DESCRIPTION "The representation of a BGP Identifier. BGP Identifiers are presented in the received network byte order. The BGP Identifier is displayed as if it is an IP address, even if it would be an illegal one." REFERENCE "RFC 4273, Section 4.2" SYNTAX OCTET STRING(SIZE (4)) Os10Bgp4V2AddressFamilyIdentifierTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The representation of a BGP AFI. The value of this object should be restricted to be between the values of 0 and 65535." REFERENCE "RFC 4760, Section 3" SYNTAX INTEGER { ipv4(1), ipv6(2) } Os10Bgp4V2SubsequentAddressFamilyIdentifierTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The representation of a BGP SAFI" REFERENCE "RFC 4760, Section 3. The value of this object should be restricted to be between the values of 0 and 255." SYNTAX INTEGER { unicast(1), multicast(2), mpls(4) } -- Top level components of this MIB module -- Notifications os10bgp4V2Notifications OBJECT IDENTIFIER ::= { os10Bgp4V2Mib 0 } -- Objects os10bgp4V2Objects OBJECT IDENTIFIER ::= { os10Bgp4V2Mib 1 } -- Conformance os10bgp4V2Conformance OBJECT IDENTIFIER ::= { os10Bgp4V2Mib 2 } -- -- Per-instance BGP discontinuities -- os10bgp4V2DiscontinuityTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2DiscontinuityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of BGP-4 discontinuities. Discontinuities that have external visibility occur on a per-BGP instance basis. Transitions by a given BGP peer will result in a consistent BGP view within that instance and thus do not represent a discontinuity from a protocol standpoint." ::= { os10bgp4V2Objects 1 } os10bgp4V2DiscontinuityEntry OBJECT-TYPE SYNTAX Os10Bgp4V2DiscontinuityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry repsenting information about a discontinuity event for a given BGP instance." INDEX { os10bgp4V2PeerInstance } ::= { os10bgp4V2DiscontinuityTable 1 } Os10Bgp4V2DiscontinuityEntry ::= SEQUENCE { os10bgp4V2DiscontinuityTime TimeStamp } os10bgp4V2DiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the most recent occasion at which this BGP management instance has suffered a discontinuity." ::= { os10bgp4V2DiscontinuityEntry 1 } -- -- Per-peer session management information. -- os10bgp4V2PeerTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers." ::= { os10bgp4V2Objects 2 } os10bgp4V2PeerEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about the connection with a remote BGP peer." INDEX { os10bgp4V2PeerInstance, os10bgp4V2PeerRemoteAddrType, os10bgp4V2PeerRemoteAddr } ::= { os10bgp4V2PeerTable 1 } Os10Bgp4V2PeerEntry ::= SEQUENCE { -- INDEX information os10bgp4V2PeerInstance Unsigned32, os10bgp4V2PeerLocalAddrType InetAddressType, os10bgp4V2PeerLocalAddr InetAddress, os10bgp4V2PeerRemoteAddrType InetAddressType, os10bgp4V2PeerRemoteAddr InetAddress, -- Local os10bgp4V2PeerLocalPort InetPortNumber, os10bgp4V2PeerLocalAs InetAutonomousSystemNumber, os10bgp4V2PeerLocalIdentifier Os10Bgp4V2IdentifierTC, -- Remote os10bgp4V2PeerRemotePort InetPortNumber, os10bgp4V2PeerRemoteAs InetAutonomousSystemNumber, os10bgp4V2PeerRemoteIdentifier Os10Bgp4V2IdentifierTC, -- Session status os10bgp4V2PeerAdminStatus INTEGER, os10bgp4V2PeerState INTEGER, os10bgp4V2PeerDescription SnmpAdminString } os10bgp4V2PeerInstance OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes routers running BGP/MPLS IP Virtual Private Networks. Implementations that do not support multiple routing instances should return 1 for this object." ::= { os10bgp4V2PeerEntry 1 } os10bgp4V2PeerLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The address family of the local end of the peering session." ::= { os10bgp4V2PeerEntry 2 } os10bgp4V2PeerLocalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The local IP address of this entry's BGP connection. An implementation is required to support IPv4 peering sessions in which case the length of this object is 4. An implementation MAY support IPv6 peering sessions in which case the length of this object is 16. IPv6 link-local peering sessions MAY be supported by this MIB. In this case the length of this object is 20." ::= { os10bgp4V2PeerEntry 3 } os10bgp4V2PeerRemoteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family of the remote end of the peering session. An implementation is required to support IPv4 peering sessions in which case the length of this object is 4. An implementation MAY support IPv6 peering sessions in which case the length of this object is 16. IPv6 link-local peering sessions MAY be supported by this MIB. In this case the length of this object is 20." ::= { os10bgp4V2PeerEntry 4 } os10bgp4V2PeerRemoteAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The remote IP address of this entry's BGP peer." ::= { os10bgp4V2PeerEntry 5 } os10bgp4V2PeerLocalPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The local port for the TCP connection between the BGP peers." ::= { os10bgp4V2PeerEntry 6 } os10bgp4V2PeerLocalAs OBJECT-TYPE SYNTAX InetAutonomousSystemNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Some implementations of BGP can represent themselves as multiple ASes. This is the AS that this peering session is representing itself as to the remote peer." ::= { os10bgp4V2PeerEntry 7 } os10bgp4V2PeerLocalIdentifier OBJECT-TYPE SYNTAX Os10Bgp4V2IdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP Identifier of the local system for this peering session. It is REQUIRED that all os10bgp4V2PeerLocalIdentifier values for the same os10bgp4V2PeerInstance be identical." REFERENCE "RFC 4271, Section 4.2, 'BGP Identifier'." ::= { os10bgp4V2PeerEntry 8 } os10bgp4V2PeerRemotePort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The remote port for the TCP connection between the BGP peers. Note that the objects os10bgp4V2PeerLocalAddr, os10bgp4V2PeerLocalPort, os10bgp4V2PeerRemoteAddr and os10bgp4V2PeerRemotePort provide the appropriate reference to the standard MIB TCP connection table, or even the ipv6 TCP MIB as in RFC 4022." REFERENCE "RFC 2012 - SNMPv2 Management Information Base for the Transmission Control Protocol using SMIv2. RFC 4022 - IP Version 6 Management Information Base for the Transmission Control Protocol." ::= { os10bgp4V2PeerEntry 9 } os10bgp4V2PeerRemoteAs OBJECT-TYPE SYNTAX InetAutonomousSystemNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The remote autonomous system number received in the BGP OPEN message." REFERENCE "RFC 4271, Section 4.2." ::= { os10bgp4V2PeerEntry 10 } os10bgp4V2PeerRemoteIdentifier OBJECT-TYPE SYNTAX Os10Bgp4V2IdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the os10bgp4V2PeerState is in the openconfirm or the established state." REFERENCE "RFC 4271, Section 4.2, 'BGP Identifier'." ::= { os10bgp4V2PeerEntry 11 } os10bgp4V2PeerAdminStatus OBJECT-TYPE SYNTAX INTEGER { halted(1), running(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The os10bgp4V2PeerState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running." REFERENCE "RFC 4271, Section 8.1.2." ::= { os10bgp4V2PeerEntry 12 } os10bgp4V2PeerState OBJECT-TYPE SYNTAX INTEGER { idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP peer connection state." REFERENCE "RFC 4271, Section 8.2.2." ::= { os10bgp4V2PeerEntry 13 } os10bgp4V2PeerDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A user configured description identifying this peer. When this object is not the empty string, this object SHOULD contain a description that is unique within a given BGP instance for this peer." ::= { os10bgp4V2PeerEntry 14 } -- -- Per-peer error management information. -- os10bgp4V2PeerErrorsTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerErrorsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "On a per-peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session." ::= { os10bgp4V2Objects 3 } os10bgp4V2PeerErrorsEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerErrorsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about errors sent and received for a particular BGP peer." AUGMENTS { os10bgp4V2PeerEntry } ::= { os10bgp4V2PeerErrorsTable 1 } Os10Bgp4V2PeerErrorsEntry ::= SEQUENCE { os10bgp4V2PeerLastErrorCodeReceived Unsigned32, os10bgp4V2PeerLastErrorSubCodeReceived Unsigned32, os10bgp4V2PeerLastErrorReceivedTime TimeStamp, os10bgp4V2PeerLastErrorReceivedText SnmpAdminString, os10bgp4V2PeerLastErrorReceivedData OCTET STRING, os10bgp4V2PeerLastErrorCodeSent Unsigned32, os10bgp4V2PeerLastErrorSubCodeSent Unsigned32, os10bgp4V2PeerLastErrorSentTime TimeStamp, os10bgp4V2PeerLastErrorSentText SnmpAdminString, os10bgp4V2PeerLastErrorSentData OCTET STRING } os10bgp4V2PeerLastErrorCodeReceived OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero." REFERENCE "RFC 4271, Section 4.5. RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 1 } os10bgp4V2PeerLastErrorSubCodeReceived OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The last subcode received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero." REFERENCE "RFC 4271, Section 4.5. RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 2 } os10bgp4V2PeerLastErrorReceivedTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The timestamp that the last NOTIFICATION was received from this peer." REFERENCE "RFC 4271, Section 4.5." ::= { os10bgp4V2PeerErrorsEntry 3 } os10bgp4V2PeerLastErrorReceivedText OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an implementation specific explanation of the error that was reported." ::= { os10bgp4V2PeerErrorsEntry 4 } os10bgp4V2PeerLastErrorReceivedData OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4075)) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code's data seen by this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated." REFERENCE "RFC 4271, Section 4.5, RFC 2578, Section 7.1.2, RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 5 } os10bgp4V2PeerLastErrorCodeSent OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero." REFERENCE "RFC 4271, Section 4.5. RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 6 } os10bgp4V2PeerLastErrorSubCodeSent OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The last subcode sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero." REFERENCE "RFC 4271, Section 4.5. RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 7 } os10bgp4V2PeerLastErrorSentTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The timestamp that the last NOTIFICATION was sent to this peer." REFERENCE "RFC 4271, Section 4.5." ::= { os10bgp4V2PeerErrorsEntry 8 } os10bgp4V2PeerLastErrorSentText OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an implementation specific explanation of the error that is being reported." ::= { os10bgp4V2PeerErrorsEntry 9 } os10bgp4V2PeerLastErrorSentData OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4075)) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code's data sent to this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated." REFERENCE "RFC 4271, Section 4.5, RFC 2578, Section 7.1.2 RFC 4486 optionally supported. RFC 3362, Section 5 optionally supported." ::= { os10bgp4V2PeerErrorsEntry 10 } -- -- Per-peer Event Times -- os10bgp4V2PeerEventTimesTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerEventTimesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the established state." ::= { os10bgp4V2Objects 4 } os10bgp4V2PeerEventTimesEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerEventTimesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains a set of statistics about time spent and events encountered in the peer session established state." AUGMENTS { os10bgp4V2PeerEntry } ::= { os10bgp4V2PeerEventTimesTable 1 } Os10Bgp4V2PeerEventTimesEntry ::= SEQUENCE { os10bgp4V2PeerFsmEstablishedTime Gauge32, os10bgp4V2PeerInUpdatesElapsedTime Gauge32 } os10bgp4V2PeerFsmEstablishedTime OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This timer indicates how long (in seconds) this peer has been in the established state or how long since this peer was last in the established state. It is set to zero when a new peer is configured or when the router is booted. If the peer has never reached the established state, the value remains zero." REFERENCE "RFC 4271, Section 8." ::= { os10bgp4V2PeerEventTimesEntry 1 } os10bgp4V2PeerInUpdatesElapsedTime OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Elapsed time (in seconds) since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0)." REFERENCE "RFC 4271, Section 4.3. RFC 4271, Section 8.2.2, Established state." ::= { os10bgp4V2PeerEventTimesEntry 2 } -- -- Per-Peer Configured Timers -- os10bgp4V2PeerConfiguredTimersTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerConfiguredTimersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Per peer management data on BGP session timers." ::= { os10bgp4V2Objects 5 } os10bgp4V2PeerConfiguredTimersEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerConfiguredTimersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry corresponds to the current state of BGP timers on a given peering session." AUGMENTS { os10bgp4V2PeerEntry } ::= { os10bgp4V2PeerConfiguredTimersTable 1 } Os10Bgp4V2PeerConfiguredTimersEntry ::= SEQUENCE { os10bgp4V2PeerConnectRetryInterval Unsigned32, os10bgp4V2PeerHoldTimeConfigured Unsigned32, os10bgp4V2PeerKeepAliveConfigured Unsigned32, os10bgp4V2PeerMinASOrigInterval Unsigned32, os10bgp4V2PeerMinRouteAdverInterval Unsigned32 } os10bgp4V2PeerConnectRetryInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval (in seconds) for the ConnectRetry timer. The suggested value for this timer is 120 seconds." REFERENCE "RFC 4271, Section 8.2.2. This is the value used to initialize the 'ConnectRetryTimer'." ::= { os10bgp4V2PeerConfiguredTimersEntry 1 } os10bgp4V2PeerHoldTimeConfigured OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 3..65535 ) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval (in seconds) for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker, using the smaller of the values in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0). If the Hold Timer has not been established with the peer this object MUST have a value of zero (0). If the bgpPeerHoldTimeConfigured object has a value of (0), then this object MUST have a value of (0)." REFERENCE "RFC 4271, Section 4.2." ::= { os10bgp4V2PeerConfiguredTimersEntry 2 } os10bgp4V2PeerKeepAliveConfigured OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 1..21845 ) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval (in seconds) for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds." REFERENCE "RFC 4271, Section 4.4. RFC 4271, Section 10." ::= { os10bgp4V2PeerConfiguredTimersEntry 3 } os10bgp4V2PeerMinASOrigInterval OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval (in seconds) for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds." REFERENCE "RFC 4271, Section 9.2.1.2. RFC 4271, Section 10." ::= { os10bgp4V2PeerConfiguredTimersEntry 4 } os10bgp4V2PeerMinRouteAdverInterval OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval (in seconds) for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds for EBGP connections and 5 seconds for IBGP connections." REFERENCE "RFC 4271, Section 9.2.1.1. RFC 4271, Section 10." ::= { os10bgp4V2PeerConfiguredTimersEntry 5 } -- -- Per-Peer Negotiated Timers -- os10bgp4V2PeerNegotiatedTimersTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerNegotiatedTimersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configured values of per-peer timers are seen in the os10bgp4V2PeerConfiguredTimersTable. Values in this table reflect the current operational values, after negotiation from values derived from initial configuration." ::= { os10bgp4V2Objects 6 } os10bgp4V2PeerNegotiatedTimersEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerNegotiatedTimersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry reflects a value of the currently operational, negotiated timer as reflected in the Os10Bgp4V2PeerNegotiatedTimersEntry." AUGMENTS { os10bgp4V2PeerEntry } ::= { os10bgp4V2PeerNegotiatedTimersTable 1 } Os10Bgp4V2PeerNegotiatedTimersEntry ::= SEQUENCE { os10bgp4V2PeerHoldTime Unsigned32, os10bgp4V2PeerKeepAlive Unsigned32 } os10bgp4V2PeerHoldTime OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 3..65535 ) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and os10bgp4V2PeerHoldTimeConfigured for this peer. If the peer is not in the established state, the value of this object is zero (0)." REFERENCE "RFC 4271, Section 4.2." ::= { os10bgp4V2PeerNegotiatedTimersEntry 1 } os10bgp4V2PeerKeepAlive OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 1..21845 ) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with os10bgp4V2PeerHoldTime, it has the same proportion as what os10bgp4V2PeerKeepAliveConfigured has when compared with os10bgp4V2PeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of os10bgp4V2PeerKeepAliveConfigured is zero (0). If the peer is not in the established state, the value of this object is zero (0)." REFERENCE "RFC 4271, Section 4.4." ::= { os10bgp4V2PeerNegotiatedTimersEntry 2 } -- -- Per-peer counters -- os10bgp4V2PeerCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PeerCountersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The counters associated with a BGP Peer." ::= { os10bgp4V2Objects 7 } os10bgp4V2PeerCountersEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PeerCountersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains counters of message transmissions and FSM transitions for a given BGP Peering session." AUGMENTS { os10bgp4V2PeerEntry } ::= { os10bgp4V2PeerCountersTable 1 } Os10Bgp4V2PeerCountersEntry ::= SEQUENCE { os10bgp4V2PeerInUpdates Counter32, os10bgp4V2PeerOutUpdates Counter32, os10bgp4V2PeerInTotalMessages Counter32, os10bgp4V2PeerOutTotalMessages Counter32, os10bgp4V2PeerFsmEstablishedTransitions Counter32 } os10bgp4V2PeerInUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of BGP UPDATE messages received on this connection." ::= { os10bgp4V2PeerCountersEntry 1 } os10bgp4V2PeerOutUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of BGP UPDATE messages transmitted on this connection." ::= { os10bgp4V2PeerCountersEntry 2 } os10bgp4V2PeerInTotalMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of messages received from the remote peer on this connection." ::= { os10bgp4V2PeerCountersEntry 3 } os10bgp4V2PeerOutTotalMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of messages transmitted to the remote peer on this connection." ::= { os10bgp4V2PeerCountersEntry 4 } os10bgp4V2PeerFsmEstablishedTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the BGP FSM transitioned into the established state for this peer." ::= { os10bgp4V2PeerCountersEntry 5 } -- -- Per-Peer Prefix Gauges -- os10bgp4V2PrefixGaugesTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2PrefixGaugesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional per-peer, per AFI-SAFI counters for prefixes" ::= { os10bgp4V2Objects 8 } os10bgp4V2PrefixGaugesEntry OBJECT-TYPE SYNTAX Os10Bgp4V2PrefixGaugesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about a bgp-peers prefix counters." INDEX { os10bgp4V2PeerInstance, os10bgp4V2PeerRemoteAddrType, os10bgp4V2PeerRemoteAddr, os10bgp4V2PrefixGaugesAfi, os10bgp4V2PrefixGaugesSafi } ::= { os10bgp4V2PrefixGaugesTable 1 } Os10Bgp4V2PrefixGaugesEntry ::= SEQUENCE { os10bgp4V2PrefixGaugesAfi Os10Bgp4V2AddressFamilyIdentifierTC, os10bgp4V2PrefixGaugesSafi Os10Bgp4V2SubsequentAddressFamilyIdentifierTC, os10bgp4V2PrefixInPrefixes Gauge32, os10bgp4V2PrefixInPrefixesAccepted Gauge32, os10bgp4V2PrefixOutPrefixes Gauge32 } os10bgp4V2PrefixGaugesAfi OBJECT-TYPE SYNTAX Os10Bgp4V2AddressFamilyIdentifierTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The AFI index of the per-peer, per prefix counters" ::= { os10bgp4V2PrefixGaugesEntry 1 } os10bgp4V2PrefixGaugesSafi OBJECT-TYPE SYNTAX Os10Bgp4V2SubsequentAddressFamilyIdentifierTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SAFI index of the per-peer, per prefix counters" ::= { os10bgp4V2PrefixGaugesEntry 2 } os10bgp4V2PrefixInPrefixes OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of prefixes received from a peer and are stored in the Adj-Ribs-In for that peer. Note that this number does not reflect prefixes that have been discarded due to policy." REFERENCE "RFC 4271, Sections 3.2 and 9." ::= { os10bgp4V2PrefixGaugesEntry 3 } os10bgp4V2PrefixInPrefixesAccepted OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of prefixes for a peer that are installed in the Adj-Ribs-In and are eligible to become active in the Loc-Rib." REFERENCE "RFC 4271, Sections 3.2 and 9." ::= { os10bgp4V2PrefixGaugesEntry 4 } os10bgp4V2PrefixOutPrefixes OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of prefixes for a peer that are installed in that peer's Adj-Ribs-Out." REFERENCE "RFC 4271, Sections 3.2 and 9." ::= { os10bgp4V2PrefixGaugesEntry 5 } -- -- BGP NLRI -- os10bgp4V2NlriTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2NlriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where os10bgp4V2NlriBest is true represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In." REFERENCE "RFC 4271, Sections 3.2 and 9." ::= { os10bgp4V2Objects 9 } os10bgp4V2NlriEntry OBJECT-TYPE SYNTAX Os10Bgp4V2NlriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a path to a network." INDEX { os10bgp4V2PeerInstance, os10bgp4V2NlriAfi, os10bgp4V2NlriSafi, os10bgp4V2NlriPrefixType, os10bgp4V2NlriPrefix, os10bgp4V2NlriPrefixLen, os10bgp4V2PeerRemoteAddrType, os10bgp4V2PeerRemoteAddr, os10bgp4V2NlriIndex } ::= { os10bgp4V2NlriTable 1 } Os10Bgp4V2NlriEntry ::= SEQUENCE { os10bgp4V2NlriIndex Unsigned32, os10bgp4V2NlriAfi Os10Bgp4V2AddressFamilyIdentifierTC, os10bgp4V2NlriSafi Os10Bgp4V2SubsequentAddressFamilyIdentifierTC, os10bgp4V2NlriPrefixType InetAddressType, os10bgp4V2NlriPrefix InetAddress, os10bgp4V2NlriPrefixLen InetAddressPrefixLength, os10bgp4V2NlriBest TruthValue, os10bgp4V2NlriCalcLocalPref Unsigned32, os10bgp4V2NlriOrigin INTEGER, os10bgp4V2NlriNextHopAddrType InetAddressType, os10bgp4V2NlriNextHopAddr InetAddress, os10bgp4V2NlriLinkLocalNextHopAddrType InetAddressType, os10bgp4V2NlriLinkLocalNextHopAddr InetAddress, os10bgp4V2NlriLocalPrefPresent TruthValue, os10bgp4V2NlriLocalPref Unsigned32, os10bgp4V2NlriMedPresent TruthValue, os10bgp4V2NlriMed Unsigned32, os10bgp4V2NlriAtomicAggregate TruthValue, os10bgp4V2NlriAggregatorPresent TruthValue, os10bgp4V2NlriAggregatorAS InetAutonomousSystemNumber, os10bgp4V2NlriAggregatorAddr Os10Bgp4V2IdentifierTC, os10bgp4V2NlriAsPathCalcLength Unsigned32, os10bgp4V2NlriAsPathString SnmpAdminString, os10bgp4V2NlriAsPath OCTET STRING, os10bgp4V2NlriPathAttrUnknown OCTET STRING } os10bgp4V2NlriIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index allows for multiple instances of a base prefix for a certain AFI-SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP." REFERENCE "RFC 3107 - Carrying Label Information in BGP-4." ::= { os10bgp4V2NlriEntry 1 } os10bgp4V2NlriAfi OBJECT-TYPE SYNTAX Os10Bgp4V2AddressFamilyIdentifierTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family of the prefix for this NLRI. Note that the AFI is not necessarily equivalent to the an InetAddressType." REFERENCE "RFC 4760 - Multiprotocol Extensions for BGP-4" ::= { os10bgp4V2NlriEntry 2 } os10bgp4V2NlriSafi OBJECT-TYPE SYNTAX Os10Bgp4V2SubsequentAddressFamilyIdentifierTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subsequent address family of the prefix for this NLRI" REFERENCE "RFC 4760 - Multiprotocol Extensions for BGP-4" ::= { os10bgp4V2NlriEntry 3 } os10bgp4V2NlriPrefixType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the os10bgp4V2NlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0)." ::= { os10bgp4V2NlriEntry 4 } os10bgp4V2NlriPrefix OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by os10bgp4V2NlriPrefixLen. Any bits beyond the length specified by os10bgp4V2NlriPrefixLen are zeroed. An implementation is required to support IPv4 prefixes. In this case, the object length is (0..4). An implementation MAY support IPv6 prefixes. In this case, the object length is (0..16)" REFERENCE "RFC 4271, Section 4.3." ::= { os10bgp4V2NlriEntry 5 } os10bgp4V2NlriPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "Length in bits of the address prefix in the Network Layer Reachability Information field." ::= { os10bgp4V2NlriEntry 6 } os10bgp4V2NlriBest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of whether or not this route was chosen as the best BGP4 route for this destination." REFERENCE "RFC 4271, Section 9.1.2." ::= { os10bgp4V2NlriEntry 7 } os10bgp4V2NlriCalcLocalPref OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The degree of preference calculated by the receiving BGP4 speaker for an advertised route. In the case where this prefix is ineligible, the value of this object will be zero (0)." REFERENCE "RFC 4271, Section 9.1.1" ::= { os10bgp4V2NlriEntry 8 } os10bgp4V2NlriOrigin OBJECT-TYPE SYNTAX INTEGER { igp(1),-- networks are interior egp(2),-- networks learned via the EGP protocol incomplete(3) -- networks that -- are learned by some other -- means } MAX-ACCESS read-only STATUS current DESCRIPTION "The ultimate origin of the path information." REFERENCE "RFC 4271, Section 4.3. RFC 4271, Section 5.1.1." ::= { os10bgp4V2NlriEntry 9 } os10bgp4V2NlriNextHopAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The address family of the address for the border router that should be used to access the destination network." ::= { os10bgp4V2NlriEntry 10 } os10bgp4V2NlriNextHopAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(4..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet associated with this prefix. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. bgpPathAttrLinkLocalNextHop will contain the linklocal scope nexthop, if it is present. In the case a mechanism is developed to use only a link local nexthop, os10bgp4V2NlriNextHopAddr will contain the link local nexthop." REFERENCE "RFC 4271, Section 4.3, RFC 4271, Section 5.1.3, RFC 2545, Section 3." ::= { os10bgp4V2NlriEntry 11 } os10bgp4V2NlriLinkLocalNextHopAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The address type for IPv6 link local addresses. This is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6. When no IPv6 link local nexthop is present, the value of this object should be unknown(0)." REFERENCE "RFC 2545, Section 3." ::= { os10bgp4V2NlriEntry 12 } os10bgp4V2NlriLinkLocalNextHopAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This value contains an IPv6 link local address and is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6. When no IPv6 link local nexthop is present, the length of this object should be zero." REFERENCE "RFC 2545, Section 3." ::= { os10bgp4V2NlriEntry 13 } os10bgp4V2NlriLocalPrefPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value is true when the LOCAL_PREF value was sent in the UPDATE message." ::= { os10bgp4V2NlriEntry 14 } os10bgp4V2NlriLocalPref OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The originating BGP4 speakers degree of preference for an advertised route." REFERENCE "RFC 4271, Section 4.3. RFC 4271, Section 5.1.5." ::= { os10bgp4V2NlriEntry 15 } os10bgp4V2NlriMedPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value is true when the MED value was sent in the UPDATE message." ::= { os10bgp4V2NlriEntry 16 } os10bgp4V2NlriMed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This metric is used to discriminate between multiple exit points to an adjacent autonomous system. When the MED value is absent but has a calculated default value, this object will contain the calculated value." REFERENCE "RFC 4271, Section 4.3. RFC 4271, Section 5.1.4." ::= { os10bgp4V2NlriEntry 17 } os10bgp4V2NlriAtomicAggregate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value is true when the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific." REFERENCE "RFC 4271, Sections 5.1.6 and 9.1.4." ::= { os10bgp4V2NlriEntry 18 } os10bgp4V2NlriAggregatorPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value is true when the AGGREGATOR path attribute was sent in the UPDATE message." ::= { os10bgp4V2NlriEntry 19 } os10bgp4V2NlriAggregatorAS OBJECT-TYPE SYNTAX InetAutonomousSystemNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The AS number of the last BGP4 speaker that performed route aggregation. When os10bgp4V2NlriAggregatorPresent is false, the value of this object should be zero (0)." REFERENCE "RFC 4271, Section 5.1.7. RFC 4271, Section 9.2.2.2." ::= { os10bgp4V2NlriEntry 20 } os10bgp4V2NlriAggregatorAddr OBJECT-TYPE SYNTAX Os10Bgp4V2IdentifierTC MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the last BGP4 speaker that performed route aggregation. When os10bgp4V2NlriAggregatorPresent is false, the value of this object should be 0.0.0.0" REFERENCE "RFC 4271, Section 5.1.7. RFC 4271, Section 9.2.2.2." ::= { os10bgp4V2NlriEntry 21 } os10bgp4V2NlriAsPathCalcLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection." REFERENCE "RFC 4271, Section 9.1.2.2.a" ::= { os10bgp4V2NlriEntry 22 } os10bgp4V2NlriAsPathString OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability. Note that SnmpAdminString is only capable of representing a maximum of 255 characters. This may lead to the string being truncated in the presence of a large AS Path. It is RECOMMENDED that when this object's contents will be truncated that the final 3 octets be reserved for the ellipses string, '...'. os10bgp4V2NlriAsPath may give access to the full AS Path." ::= { os10bgp4V2NlriEntry 23 } -- Maximum size of the following is derived as -- 4096 max message size -- - 16 BGP message marker bytes -- - 2 BGP message size -- - 1 BGP message type (UPDATE with unknown attr) -- - 2 UPDATE routes length (even assuming no routes) -- - 2 UPDATE path attributes length -- - 1 path attribute flag octet -- --------- -- 4072 bytes maximum per-message attribute value data os10bgp4V2NlriAsPath OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2..4072)) MAX-ACCESS read-only STATUS current DESCRIPTION "In order to provide a canonicalized form of the BGP-4 AS_PATH along with the human-readable os10bgp4V2NlriAsPathString, which may be truncated, this object contains the contents of the BGP-4 AS_PATH Path Attribute. This object may be parsed using the rules defined for Four-octet ASes as defined in RFC 4893. RFC 4271, Section 4.3, 'Path Attributes: b) AS_PATH' as amended by RFC 5065, Section 3 defines the general format of the AS_PATH path attribute and its code points. In brief, the AS_PATH is composed of a sequence of AS Segments. Each AS Segment is represented by a triple: . The path segment type and path segment length fields are one octet in length each. The path segment type field may be one of: 1 - AS_SET (RFC 4721, Section 4.3) 2 - AS_SEQUENCE (RFC 4721, Section 4.3) 3 - AS_CONFED_SEQUENCE (RFC 3065, Section 5) 4 - AS_CONFED_SET (RFC 3065, Section 5) The path segment length field contains the number of ASes (not the number of octets) in the path segment value field. The path segment value field contains one or more AS numbers, each encoded as a 4-octet length field in network byte order. Note that since an SNMP agent may truncate this object to less than its maximum theoretical length of 4072 octets users of this object should be prepared to deal with a truncated and thus malformed AS_PATH. It is RECOMMENDED that when such truncation would occur on the boundary of an encoded AS that the partial AS be discarded from this object and the object's size be adjusted accordingly. Further, it is also RECOMMENDED that when such truncation, either alone or in conjuction with the truncation of a partially encoded AS described previously, would yield an empty path segment value field that the path segment type and path segment length components of the truncated AS_PATH also be discarded and the object's size be adjusted accordingly." REFERENCE "RFC 4271, Section 4.3. RFC 5065, Section 5. RFC 4893." ::= { os10bgp4V2NlriEntry 24 } os10bgp4V2NlriPathAttrUnknown OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4072)) MAX-ACCESS read-only STATUS current DESCRIPTION "Path Attributes not understood by this implementation SHOULD be be presented in this object. Those Path Attributes use the type, length, value encoding documented in RFC 4271, Section 4.3, 'Path Attributes'. Note that since an SNMP agent may truncate this object to less than its maximum theoretical length of 4072 octets users of this object should be prepared to deal with a truncated and thus malformed Path Attribute." REFERENCE "RFC 4271, Section 4.3." ::= { os10bgp4V2NlriEntry 25 } -- -- Adj-Ribs-Out Table -- os10bgp4V2AdjRibsOutTable OBJECT-TYPE SYNTAX SEQUENCE OF Os10Bgp4V2AdjRibsOutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains on a per-peer basis one or more routes from the os10bgp4V2NlriTable that have been placed in this peer's Adj-Ribs-Out." REFERENCE "RFC 4271, Section 3.2." ::= { os10bgp4V2Objects 10 } os10bgp4V2AdjRibsOutEntry OBJECT-TYPE SYNTAX Os10Bgp4V2AdjRibsOutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of BGP routes that have been placed into a peer's Adj-Ribs-Out." INDEX { os10bgp4V2PeerInstance, os10bgp4V2NlriAfi, os10bgp4V2NlriSafi, os10bgp4V2NlriPrefixType, os10bgp4V2NlriPrefix, os10bgp4V2NlriPrefixLen, os10bgp4V2PeerRemoteAddrType, os10bgp4V2PeerRemoteAddr, os10bgp4V2AdjRibsOutIndex } ::= { os10bgp4V2AdjRibsOutTable 1 } Os10Bgp4V2AdjRibsOutEntry ::= SEQUENCE { os10bgp4V2AdjRibsOutIndex Unsigned32, os10bgp4V2AdjRibsOutRoute RowPointer } os10bgp4V2AdjRibsOutIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Certain extensions to BGP permit multiple instance of a per afi, per safi prefix to be advertised to a peer. This object allows the enumeration of them." ::= { os10bgp4V2AdjRibsOutEntry 1 } os10bgp4V2AdjRibsOutRoute OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object points to the route in the os10bgp4V2NlriTable that corresponds to the entry in the peer's Adj-Rib-Out. Outgoing route maps are not reflected at this point as those are part of the Update-Send process." REFERENCE "RFC 4271, Section 9.2." ::= { os10bgp4V2AdjRibsOutEntry 2 } END