-- ***************************************************************** -- DLINKSW-LBD-MIB.mib : Loopback Detection MIB -- -- Copyright (c) 2014 D-Link Corporation, all rights reserved. -- -- ***************************************************************** DLINKSW-LBD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString,TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF InterfaceIndex FROM IF-MIB VlanId FROM Q-BRIDGE-MIB Dlink2kVlanList FROM DLINKSW-TC-MIB dlinkIndustrialCommon FROM DLINK-ID-REC-MIB; dlinkSwLoopbackDetectMIB MODULE-IDENTITY LAST-UPDATED "201410270000Z" ORGANIZATION "D-Link Corp." CONTACT-INFO " D-Link Corporation Postal: No. 289, Sinhu 3rd Rd., Neihu District, Taipei City 114, Taiwan, R.O.C Tel: +886-2-66000123 E-mail: tsd@dlink.com.tw " DESCRIPTION "This MIB module defines objects for loopback detection." REVISION "201410270000Z" DESCRIPTION "Add node dLbdAddressType." REVISION "201310230000Z" DESCRIPTION "Add node dLbdActMode, dLbdNotifyEnabled and dLbdNotifyInfo." REVISION "201302050000Z" DESCRIPTION "This is the first version of the MIB file for 'loopback detection' functionality." ::= { dlinkIndustrialCommon 46 } -- ----------------------------------------------------------------------------- dLbdNotifications OBJECT IDENTIFIER ::= { dlinkSwLoopbackDetectMIB 0 } dLbdObjects OBJECT IDENTIFIER ::= { dlinkSwLoopbackDetectMIB 1 } dLbdConformance OBJECT IDENTIFIER ::= { dlinkSwLoopbackDetectMIB 2 } dLbdCtrlInterval OBJECT-TYPE SYNTAX INTEGER (1..32767) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the interval in seconds at which LBD packets are transmitted." ::= { dLbdObjects 1 } dLbdCtrlGlobalEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the loopback detection is enabled globally. " ::= { dLbdObjects 2 } dLbdCtrlMode OBJECT-TYPE SYNTAX INTEGER { portBased(1), vlanBased(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the loopback detection mode. portBased(1) - The loopback detection works in port-based mode. vlanBased(2) - The loopback detection works in vlan-based mode." ::= { dLbdObjects 3 } dLbdActMode OBJECT-TYPE SYNTAX INTEGER { shutdown(1), none(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the loopback detection action mode. shundown(1) - When loop has been detected, the port will be shut down (disabled) in port-based mode, the traffic will be block on specific VLAN in VLAN-based mode. This is the default value. none(2) - When loop has been detected, the port will NOT be disabled in port-based mode, the traffic will NOT be block on specific VLAN in VLAN-based mode. Just send log and trap." ::= { dLbdObjects 6 } dLbdNotifyEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to 'true' to enable global SNMP notification for loopback detection feature. Setting the object to 'false' will disable SNMP notifications." ::= { dLbdObjects 7} dLbdIfCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF DLbdIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of loopback detection information entries." ::= { dLbdObjects 4 } dLbdAddressType OBJECT-TYPE SYNTAX INTEGER { multicast(1), broadcast(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the CTP packet's DA type. multicast(1) - Only multicast CTP packet will be sent.The CTP packet's DA is CF-00-00-00-00-00. broadcast(2) - Only broadcast CTP packet will be sent.The CTP packet's DA is FF-FF-FF-FF-FF-FF." ::= { dLbdObjects 9 } dLbdIfCfgEntry OBJECT-TYPE SYNTAX DLbdIfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry indicates the setting of loopback detection on an interface." INDEX { dLbdIfCfgIndex } ::= { dLbdIfCfgTable 1 } DLbdIfCfgEntry ::= SEQUENCE { dLbdIfCfgIndex InterfaceIndex, dLbdIfCfgEnabled TruthValue, dLbdIfLoopStatus INTEGER, dLbdIfLoopVlans DisplayString } dLbdIfCfgIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the ifIndex of the physical port or port channel." ::= { dLbdIfCfgEntry 1 } dLbdIfCfgEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the loopback detection is enabled on the interface. " ::= { dLbdIfCfgEntry 2 } dLbdIfLoopStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), loop(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the interface loopback status." ::= { dLbdIfCfgEntry 3 } dLbdIfLoopVlans OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN list that has detected a loopback." ::= { dLbdIfCfgEntry 4 } -- ---------------------------------------------------------------------------- dLbdVlanCtrlObjects OBJECT-IDENTITY STATUS current DESCRIPTION "This identifier defines a subtree under which a set of objects are defined to enable loopback detection on specific VLANs. That is, LBD Control packet will be sent out for the VLAN that the port has the membership and within the specified VLAN list (the correspondig bit is '1'). When enabled VLAN ID list is empty, that is both dLbdVlanCrlFirst2K and dLbdVlanCrlSecond2K are zero lenth string, LBD Control packet is sent out for all VLANs that the port has the membership." ::= { dLbdObjects 5 } dLbdVlanCrlFirst2K OBJECT-TYPE SYNTAX Dlink2kVlanList MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the loopback detection enabled VLAN in a string of octets containing one bit per VLAN for VLANs 1 to 2048. If the bit is set to '1', then the VLAN is enabled for loopback detection." ::= { dLbdVlanCtrlObjects 1 } dLbdVlanCrlSecond2K OBJECT-TYPE SYNTAX Dlink2kVlanList MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the loopback detection enabled VLAN in a string of octets containing one bit per VLAN for VLANs 2049 to 4095. If the bit is set to '1', then the VLAN is enabled for loopback detection." ::= { dLbdVlanCtrlObjects 2 } -- ----------------------------------------------------------------------------- -- ----------------------------------------------------------------------------- dLbdNotifyInfo OBJECT-IDENTITY STATUS current DESCRIPTION "This identifier is a group for variable bindings for traps." ::= { dLbdObjects 8 } dLbdNotifyInfoIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the interface id that has detected a loopback." ::= { dLbdNotifyInfo 1 } dLbdNotifyInfoVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the vlan id that has detected a loopback." ::= { dLbdNotifyInfo 2 } -- ----------------------------------------------------------------------------- -- ----------------------------------------------------------------------------- -- MIB Notifications statements -- ----------------------------------------------------------------------------- dLbdLoopOccurred NOTIFICATION-TYPE OBJECTS { dLbdNotifyInfoIfIndex } STATUS current DESCRIPTION "This trap is sent when an interface loop occurs." ::= { dLbdNotifications 1 } dLbdLoopRestart NOTIFICATION-TYPE OBJECTS { dLbdNotifyInfoIfIndex } STATUS current DESCRIPTION "This trap is sent when an interface loop restarts after the interval time." ::= { dLbdNotifications 2 } dLbdVlanLoopOccurred NOTIFICATION-TYPE OBJECTS { dLbdNotifyInfoIfIndex, dLbdNotifyInfoVlanId } STATUS current DESCRIPTION "This trap is sent when an interface with a VID loop occurs." ::= { dLbdNotifications 3 } dLbdVlanLoopRestart NOTIFICATION-TYPE OBJECTS { dLbdNotifyInfoIfIndex, dLbdNotifyInfoVlanId } STATUS current DESCRIPTION "This trap is sent when an interface loop with a VID restarts after the interval time." ::= { dLbdNotifications 4 } -- ----------------------------------------------------------------------------- -- MIB Conformance statements -- ----------------------------------------------------------------------------- dLbdMIBCompliances OBJECT IDENTIFIER ::= { dLbdConformance 1 } dLbdMIBGroups OBJECT IDENTIFIER ::= { dLbdConformance 2 } dLbdMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the DLINKSW-LBD-MIB." MODULE -- this module MANDATORY-GROUPS { dLbdCfgGroup, dLbdIfCfgGroup } GROUP dLbdCtrlModeGroup DESCRIPTION "This group is mandatory if vlan-based mode is supported." GROUP dLbdVlanCtrlGroup DESCRIPTION "This group is mandatory if vlan-based mode is supported." ::= { dLbdMIBCompliances 1 } -- ----------------------------------------------------------------------------- dLbdCfgGroup OBJECT-GROUP OBJECTS { dLbdCtrlInterval, dLbdCtrlGlobalEnabled, dLbdActMode, dLbdNotifyEnabled, dLbdNotifyInfoIfIndex, dLbdNotifyInfoVlanId, dLbdAddressType } STATUS current DESCRIPTION "A collection of objects providing management of the loopback detection feature." ::= { dLbdMIBGroups 1 } dLbdIfCfgGroup OBJECT-GROUP OBJECTS { dLbdIfCfgEnabled, dLbdIfLoopStatus, dLbdIfLoopVlans } STATUS current DESCRIPTION "A collection of objects providing the per-interface control of loopback detection." ::= { dLbdMIBGroups 2 } dLbdCtrlModeGroup OBJECT-GROUP OBJECTS { dLbdCtrlMode } STATUS current DESCRIPTION "A collection of objects providing the mode of loopback detection." ::= { dLbdMIBGroups 3 } dLbdVlanCtrlGroup OBJECT-GROUP OBJECTS { dLbdVlanCrlFirst2K, dLbdVlanCrlSecond2K } STATUS current DESCRIPTION "A collection of objects providing the VLAN list of loopback detection." ::= { dLbdMIBGroups 4 } dLbdNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { dLbdLoopOccurred, dLbdLoopRestart, dLbdVlanLoopOccurred, dLbdVlanLoopRestart } STATUS current DESCRIPTION "A collection of notifications used for monitoring the hosts under the control of loopback detection." ::= { dLbdMIBGroups 5 } END