HUAWEI-MPLSOAM-PS-MIB DEFINITIONS ::= BEGIN
 
        IMPORTS
            hwMplsOam            
                FROM HUAWEI-MPLSOAM-MIB            
            InterfaceIndex            
                FROM IF-MIB            
            OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP            
                FROM SNMPv2-CONF            
            IpAddress, Integer32, Unsigned32, OBJECT-TYPE, NOTIFICATION-TYPE            
                FROM SNMPv2-SMI            
            RowStatus, TruthValue            
                FROM SNMPv2-TC;
    
    
    
--
-- Node definitions
--
    
        hwMplsOamPs OBJECT IDENTIFIER ::= { hwMplsOam 1 }

        
        hwMplsPsObjects OBJECT IDENTIFIER ::= { hwMplsOamPs 3 }

        
        hwMplsPsTable OBJECT-TYPE
            SYNTAX SEQUENCE OF HwMplsPsEntry
            MAX-ACCESS not-accessible
            STATUS current
            DESCRIPTION
                "This table specifies per-protection-group MPLS PS 
                capability and associated information.
                "
            ::= { hwMplsPsObjects 1 }

        
        hwMplsPsEntry OBJECT-TYPE
            SYNTAX HwMplsPsEntry
            MAX-ACCESS not-accessible
            STATUS current
            DESCRIPTION
                "An entry in this table is created by an LSR for every 
                protection group capable of supporting mpls ps."
            INDEX { hwMplsPsIndex }
            ::= { hwMplsPsTable 1 }

        
        HwMplsPsEntry ::=
            SEQUENCE { 
                hwMplsPsIndex
                    Unsigned32,
                hwMplsPsType
                    Integer32,
                hwMplsPsWorkTunnName
                    OCTET STRING,
                hwMplsPsWorkTunnId
                    Integer32,
                hwMplsPsProtectTunnName
                    OCTET STRING,
                hwMplsPsProtectTunnId
                    Integer32,
                hwMplsPsRevertiveMode
                    Integer32,
                hwMplsPsWTR
                    Integer32,
                hwMplsPsHoldOff
                    Integer32,
                hwMplsPsSwitchCondition
                    Integer32,
                hwMplsPsWorkTunnelState
                    Integer32,
                hwMplsPsProtTunnelState
                    Integer32,
                hwMplsPsSwitchResult
                    Integer32,
                hwMplsPsCfgType
                    Integer32,
                hwMplsPsCfgProtectTunnId
                    Integer32,
                hwMplsPsCfgRevertiveMode
                    Integer32,
                hwMplsPsCfgWTR
                    Integer32,
                hwMplsPsCfgHoldOff
                    Integer32,
                hwMplsPsRowStatus
                    RowStatus
             }

        hwMplsPsIndex OBJECT-TYPE
            SYNTAX Unsigned32
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "This is a unique index for an entry in the mplspsEntry.
                
                "
            ::= { hwMplsPsEntry 1 }

        
        hwMplsPsType OBJECT-TYPE
            SYNTAX Integer32 (1..4)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The type of protection switch,can be 1:1,1+1,shared mesh,
                packet 1+1,the default choice is 1:1.
                In the 1+1 architecture type, a protection LSP is dedicated to 
                each working LSP with the working LSP bridged onto the 
                protection LSP at the source of the protection domain. 
                The traffic on working and protection LSPs is transmitted 
                simultaneously to the sink of the protection domain, 
                where a selection between the working and protection LSP is 
                made, based on some predetermined criteria, such as defect 
                indication.
                In the 1:1 architecture type, a protection LSP is dedicated to 
                each working LSP. The working traffic is transmitted either by 
                working or protection LSP.
                In the shared mesh architecture type, possible sharing of 
                protection capacity between disjoint link, node in the network 
                is achieved while guaranteeing recovery from a single failure.
                In the packet 1+1 architecture type, the traffic is transmitted 
                simultaneously onto two possibly disjoint routed LSPs to the 
                sink of the protection domain. Each pair of duplicate 
                transmitted packets is assigned the same identifier (sequence 
                number) but distinct from the other pairs of duplicate packets. 
                At the sink of the protection domain packet level selection 
                mechanism is employed to select one of the two possibly 
                received copies of each packet. 
                1:  1:1 protection switching,;
                2:  1+1 protection switching;
                3:  shared mesh protection swiching;
                4:  packet 1+1 protection switching.
                "
            ::= { hwMplsPsEntry 2 }

        
        hwMplsPsWorkTunnName OBJECT-TYPE
            SYNTAX OCTET STRING
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "The name of work-tunnel."
            ::= { hwMplsPsEntry 3 }

        
        hwMplsPsWorkTunnId OBJECT-TYPE
            SYNTAX Integer32 (1..65535)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Work-tunnel id(session-tunnel-id)."
            ::= { hwMplsPsEntry 4 }

        
        hwMplsPsProtectTunnName OBJECT-TYPE
            SYNTAX OCTET STRING
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The name of protect-tunnel."
            ::= { hwMplsPsEntry 5 }

        
        hwMplsPsProtectTunnId OBJECT-TYPE
            SYNTAX Integer32 (1..65535)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Protect-tunnel id(session-tunnel-id)."
            ::= { hwMplsPsEntry 6 }

        
        hwMplsPsRevertiveMode OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Revertive mode is a protection switching mode where revertive 
                action (switch back to the working LSP) is taken after the 
                working LSP is repaired.And switching does not occur in a
                non-revertive mode.
                1: revertive;
                2: non-revertive;
                "
            ::= { hwMplsPsEntry 7 }

        
        hwMplsPsWTR OBJECT-TYPE
            SYNTAX Integer32 (0..60)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Wait to Restore timer is only applicable for the revertive mode 
                and applies to a working LSP,It prevents reversion back to 
                select the working LSP until the Wait to Restore timer has 
                expired.The default value is 12 minutes.step is 30s."
            ::= { hwMplsPsEntry 8 }

        
        hwMplsPsHoldOff OBJECT-TYPE
            SYNTAX Integer32 (0..100)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The time between declaration of signal degrade or signal fail, 
                and the initialization of the protection switching algorithm.
                step is 100ms.maximum is 10s."
            ::= { hwMplsPsEntry 9 }

        
        hwMplsPsSwitchCondition OBJECT-TYPE
            SYNTAX Integer32 (1..9)
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
                "The current switch condition of the protection group.
                1: clear,This command clears all of the externally 
                   initiated switch commands listed below;
                2: lockout of protection,Fix the selector position on the 
                   working LSP,Prevents the selector from switching to the 
                   protection LSP when it is selecting the working LSP. 
                   Switches the selector from the protection to the working LSP 
                   when it is selecting the protection LSP;
                3: forced protection,Switches the selector from the working LSP 
                   to the protection LSP (unless a higher priority switch 
                   request (i.e., LoP) is in effect);
                4: signal fail,for 1:1,Signal Fail (SF) is declared when the 
                   source of the protection domain enters the Defect State by 
                   receiving a BDI packet (from the return LSP or out of band).
                5: manual switch for working-lsp,Switches the selector from the 
                   working LSP to the protection LSP (unless an equal or higher 
                   priority switch request (i.e., LoP, FS, SF or MS) is in 
                   effect);
                6: manual switch for protection-lsp,Switches the selector from 
                   the protection LSP to the working LSP (unless an equal or 
                   higher priority switch request (i.e., LoP, FS, SF or MS) is 
                   in effect).
                7: WTR-timer;
                8: HoldOff-timer;
                9: Others;
                The pripority of the commands are:
                clear > lockout of protection > force switch > manual switch for working
                lsp = manual switch for protection lsp"
            ::= { hwMplsPsEntry 10 }

        
        hwMplsPsWorkTunnelState OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The state of working tunnel state in one protection group,
                whether it is in detection,
                1: it is outof defect
                2: it enters defect
                "
            ::= { hwMplsPsEntry 11 }

        
        hwMplsPsProtTunnelState OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The state of protection tunnel state in one protection group,
                whether it is in detection,
                1: it is outof defect
                2: it enters defect"
            ::= { hwMplsPsEntry 12 }

        
        hwMplsPsSwitchResult OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Which tunnel is used to transfer the data stream.
                1: working-tunnel
                2: protection-tunnel"
            ::= { hwMplsPsEntry 13 }

        
        hwMplsPsCfgType OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "The type of protection switch which is configured.
                1: 1:1
                2: 1+1
                3: shared mesh
                4: packet 1:1"
            ::= { hwMplsPsEntry 14 }

        
        hwMplsPsCfgProtectTunnId OBJECT-TYPE
            SYNTAX Integer32 (1..65535)
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Protect-tunnel id(session-tunnel-id)."
            ::= { hwMplsPsEntry 15 }

        
        hwMplsPsCfgRevertiveMode OBJECT-TYPE
            SYNTAX Integer32 (1..2)
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Revertive mode is a protection switching mode where revertive 
                action (switch back to the working LSP) is taken after the 
                working LSP is repaired.And switching does not occur in a
                non-revertive mode.
                1: revertive;
                2: non-revertive;
                
                "
            ::= { hwMplsPsEntry 16 }

        
        hwMplsPsCfgWTR OBJECT-TYPE
            SYNTAX Integer32 (0..60)
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Wait to Restore timer is only applicable for the revertive mode 
                and applies to a working LSP,It prevents reversion back to 
                select the working LSP until the Wait to Restore timer has 
                expired.The default value is 12 minutes.step is 30s."
            ::= { hwMplsPsEntry 17 }

        
        hwMplsPsCfgHoldOff OBJECT-TYPE
            SYNTAX Integer32 (0..100)
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
                "The time between declaration of signal degrade or signal fail, 
                and the initialization of the protection switching algorithm.
                step is 100ms.maximum is 10s."
            ::= { hwMplsPsEntry 18 }

        
        hwMplsPsRowStatus OBJECT-TYPE
            SYNTAX RowStatus
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
                "This variable is used to create, modify, and
                delete a row in this table.
                1: active
                2: not in service
                3: not ready
                4: create and go
                5: create and wait
                6: destroy"
            ::= { hwMplsPsEntry 19 }

        
        hwTunnPsTrapOpen OBJECT-TYPE
            SYNTAX Unsigned32 (1..2)
            MAX-ACCESS read-write
            STATUS current
            DESCRIPTION
                "1:enable;
                2:disable;"
            ::= { hwMplsPsObjects 2 }

        
        hwMplsVCPsTable OBJECT-TYPE
            SYNTAX SEQUENCE OF HwMplsVCPsEntry
            MAX-ACCESS not-accessible
            STATUS current
            DESCRIPTION
                "Description."
            ::= { hwMplsPsObjects 3 }

        
        hwMplsVCPsEntry OBJECT-TYPE
            SYNTAX HwMplsVCPsEntry
            MAX-ACCESS not-accessible
            STATUS current
            DESCRIPTION
                "this table for these commands
                1.mpls te protection tunnel XXX
                2. mpls te reverse-lsp { lsp-name XXXX | lsr-id X.X.X.X tunnel-id x }                                               
                3. mpls te reserved-for-binding  "
            INDEX { hwMplsVCPsIfIndex }
            ::= { hwMplsVCPsTable 1 }

        
        HwMplsVCPsEntry ::=
            SEQUENCE { 
                hwMplsVCPsIfIndex
                    InterfaceIndex,
                hwMplsVCPsTNLBinding
                    TruthValue,
                hwMplsTeReverseLspName
                    OCTET STRING,
                hwMplsVcPsRowStatus
                    RowStatus,
                hwMplsTeReverseLspLsrId
                    IpAddress,
                hwMplsTeReverseLspTunnId
                    Integer32
             }

        hwMplsVCPsIfIndex OBJECT-TYPE
            SYNTAX InterfaceIndex
            MAX-ACCESS read-only
            STATUS current
            DESCRIPTION
                "Description.the  index of working tunnel interface of Protection group  "
            ::= { hwMplsVCPsEntry 1 }

        
        hwMplsVCPsTNLBinding OBJECT-TYPE
            SYNTAX TruthValue
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Description.it is used by command ' mpls te reserved-for-binding '"
            ::= { hwMplsVCPsEntry 2 }

        
        hwMplsTeReverseLspName OBJECT-TYPE
            SYNTAX OCTET STRING
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Description.it is used for command ' mpls te reverse-lsp lspname'"
            ::= { hwMplsVCPsEntry 3 }

        
        hwMplsVcPsRowStatus OBJECT-TYPE
            SYNTAX RowStatus
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Description.
                1: active;
                2: notInservice;
                3: notReady;
                4: CreateAndGo;
                5: CreateAndWait;
                6: destroy;"
            ::= { hwMplsVCPsEntry 4 }

        
        hwMplsTeReverseLspLsrId OBJECT-TYPE
            SYNTAX IpAddress
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Description.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'"
            ::= { hwMplsVCPsEntry 5 }

        
        hwMplsTeReverseLspTunnId OBJECT-TYPE
            SYNTAX Integer32 (1..65535)
            MAX-ACCESS read-create
            STATUS current
            DESCRIPTION
                "Description.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'"
            ::= { hwMplsVCPsEntry 6 }

        
        hwMplsPsNotifications OBJECT IDENTIFIER ::= { hwMplsOamPs 4 }

        
        hwMplsPsSwitchPtoW NOTIFICATION-TYPE
            OBJECTS { hwMplsPsWorkTunnName, hwMplsPsWorkTunnId, hwMplsPsProtectTunnName, hwMplsPsProtectTunnId, hwMplsPsSwitchResult
                 }
            STATUS current
            DESCRIPTION 
                "This notification is generated when switching from
                protection-lsp to working-lsp occured."
            ::= { hwMplsPsNotifications 1 }

        
        hwMplsPsSwitchWtoP NOTIFICATION-TYPE
            OBJECTS { hwMplsPsWorkTunnName, hwMplsPsWorkTunnId, hwMplsPsProtectTunnName, hwMplsPsProtectTunnId, hwMplsPsSwitchResult
                 }
            STATUS current
            DESCRIPTION 
                "This notification is generated when switching from woking-lsp
                to protection-lsp occured.
                "
            ::= { hwMplsPsNotifications 2 }

        
        hwMplsOamPsConformance OBJECT IDENTIFIER ::= { hwMplsOamPs 100 }

        
        hwMplsOamPsCompliances OBJECT IDENTIFIER ::= { hwMplsOamPsConformance 1 }

        
        hwMplsOamPsGroupCompliance MODULE-COMPLIANCE
            STATUS current
            DESCRIPTION 
                "The compliance statement for mpls oam ps."
            MODULE -- this module
                MANDATORY-GROUPS { hwMplsPsGroup, hwMplsVcPsGroup }
            ::= { hwMplsOamPsCompliances 1 }

        
        hwMplsOamPsGroups OBJECT IDENTIFIER ::= { hwMplsOamPsConformance 2 }

        
        hwMplsPsGroup OBJECT-GROUP
            OBJECTS { hwMplsPsType, hwMplsPsWorkTunnName, hwMplsPsWorkTunnId, hwMplsPsProtectTunnName, hwMplsPsProtectTunnId, 
                hwMplsPsRevertiveMode, hwMplsPsWTR, hwMplsPsHoldOff, hwMplsPsSwitchCondition, hwMplsPsWorkTunnelState, 
                hwMplsPsProtTunnelState, hwMplsPsSwitchResult, hwMplsPsCfgType, hwMplsPsCfgProtectTunnId, hwMplsPsCfgRevertiveMode, 
                hwMplsPsCfgWTR, hwMplsPsCfgHoldOff, hwMplsPsRowStatus, hwTunnPsTrapOpen, hwMplsVCPsIfIndex, 
                hwMplsPsIndex }
            STATUS current
            DESCRIPTION 
                "The compliance statement for mpls oam ps management."
            ::= { hwMplsOamPsGroups 1 }

        
        hwMplsVcPsGroup OBJECT-GROUP
            OBJECTS { hwMplsVCPsTNLBinding, hwMplsTeReverseLspName, hwMplsVcPsRowStatus, hwMplsTeReverseLspLsrId, hwMplsTeReverseLspTunnId
                 }
            STATUS current
            DESCRIPTION 
                "The compliance statement for mpls oam ps reverse lsp."
            ::= { hwMplsOamPsGroups 2 }

        
        hwMplsPsNotificationGroup NOTIFICATION-GROUP
            NOTIFICATIONS { hwMplsPsSwitchPtoW, hwMplsPsSwitchWtoP }
            STATUS current
            DESCRIPTION 
                "Description."
            ::= { hwMplsOamPsGroups 3 }

        
    
    END