-- extracted from pw-atm-draft-06 JUNIPER-PW-ATM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64, Unsigned32, mib-2 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TruthValue, RowStatus, RowPointer FROM SNMPv2-TC PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB -- Juniper Specific ATM MIB jnxMibs FROM JUNIPER-SMI -- *** JNX *** jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex FROM JUNIPER-VPN-MIB InterfaceIndex FROM IF-MIB AtmVpIdentifier, AtmVcIdentifier FROM ATM-TC-MIB; jnxPWAtmMIB MODULE-IDENTITY LAST-UPDATED "200909010000Z" -- 2008 ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) Working Group" CONTACT-INFO "Juniper Technical Assistance Center Juniper Networks, Inc. 1133 Innovation Way Sunnyvale, CA 94089 E-mail: support@juniper.net" DESCRIPTION "This MIB module defines objects used for managing the atm pseudowires in Juniper products." -- Revision history. REVISION "200909010000Z" -- 2008 DESCRIPTION " This mib is a modified version of RFC 5605" ::= { jnxMibs 57} jnxpwAtmNotifications OBJECT IDENTIFIER ::= { jnxPWAtmMIB 0 } jnxpwAtmObjects OBJECT IDENTIFIER ::= { jnxPWAtmMIB 1 } jnxpwAtmConformance OBJECT IDENTIFIER ::= { jnxPWAtmMIB 2 } --Generic ATM PW table for all types of ATM PW connection. jnxpwAtmCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies generic information for an ATM PW to be carried over PSN in any mode." ::= { jnxpwAtmObjects 1 } jnxpwAtmCfgEntry OBJECT-TYPE SYNTAX JnxPwAtmCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters for the ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable. An entry is created for every newly ATM type associated pwIndex in the pwTable. Unless otherwise specified, all read-write objects in this table MAY be changed when the PW is defined as not active and all RW objects values must persist after reboot" REFERENCE "See [PWMIB] " INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } ::= { jnxpwAtmCfgTable 1 } JnxPwAtmCfgEntry ::= SEQUENCE { jnxpwAtmCfgMaxCellConcatenation Unsigned32, jnxpwAtmCfgFarEndMaxCellConcatenation Unsigned32, jnxpwAtmCfgTimeoutMode INTEGER, jnxpwAtmClpQosMapping TruthValue } jnxpwAtmCfgMaxCellConcatenation OBJECT-TYPE SYNTAX Unsigned32 (1..29) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ATM cells that can be concatenated into one PW packet towards PSN. In non LDP or other signaling protocol environment, this object MAY be changed at anytime, but traffic might be interuppted, otherwise, it may be changed when PW is not active." ::= { jnxpwAtmCfgEntry 1 } jnxpwAtmCfgFarEndMaxCellConcatenation OBJECT-TYPE SYNTAX Unsigned32 (1..29) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will either return value 0 or allow setting it for calculating protocol overhead." ::= { jnxpwAtmCfgEntry 2 } jnxpwAtmCfgTimeoutMode OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), disabled (2), enabled (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the time out is implementation specific-as such this object may be changed at any time under proper consideration of traffic interupption effect." ::= { jnxpwAtmCfgEntry 3 } jnxpwAtmClpQosMapping OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields of the encapsulating protocol (e.g. EXP fields of the MPLS Label Stack). Selecting True allows the drop precedence to be preserved across the PSN. In transparent cell transport, the value of this object MUST be false(2), in other cases it can be changed at any time." REFERENCE "See [ATMENCAP] section 12" ::= { jnxpwAtmCfgEntry 4 } -- Device capable of implementing N:1, 1:1 and transparent cell -- mode assumes to support the N:1 table for all -- modes with respective applicable setting. -- In such implementation, user can create an entry for either -- 1:1 or transparent cell transport modes only -- in pwAtmInboundNto1Table. The side effect of such -- will be an automatic create of the respective line in the -- pwAtmOutboundNto1Table. -- ATM PW Outbound Table for N to 1 connection jnxpwAtmOutboundNto1Table OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmOutboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3). " ::= { jnxpwAtmObjects 2 } jnxpwAtmOutboundNto1Entry OBJECT-TYPE SYNTAX JnxPwAtmOutboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all read-create objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot." INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } ::= { jnxpwAtmOutboundNto1Table 1 } JnxPwAtmOutboundNto1Entry ::= SEQUENCE { jnxpwAtmOutboundNto1AtmIf InterfaceIndex, jnxpwAtmOutboundNto1Vpi AtmVpIdentifier, jnxpwAtmOutboundNto1Vci AtmVcIdentifier, jnxpwAtmOutboundNto1RowStatus RowStatus, jnxpwAtmOutboundNto1TrafficParamDescr RowPointer, jnxpwAtmOutboundNto1MappedVpi AtmVpIdentifier, jnxpwAtmOutboundNto1MappedVci AtmVcIdentifier } jnxpwAtmOutboundNto1AtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Interface that receives cells from the ATM network." ::= { jnxpwAtmOutboundNto1Entry 1 } jnxpwAtmOutboundNto1Vpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF" ::= { jnxpwAtmOutboundNto1Entry 2 } jnxpwAtmOutboundNto1Vci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF" ::= { jnxpwAtmOutboundNto1Entry 3 } jnxpwAtmOutboundNto1RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { jnxpwAtmOutboundNto1Entry 4 } jnxpwAtmOutboundNto1TrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort." ::= { jnxpwAtmOutboundNto1Entry 5 } jnxpwAtmOutboundNto1MappedVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active " ::= { jnxpwAtmOutboundNto1Entry 6 } jnxpwAtmOutboundNto1MappedVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The egress generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active." ::= { jnxpwAtmOutboundNto1Entry 7 } -- ATM PW Inbound Table for N to 1 connection jnxpwAtmInboundNto1Table OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmInboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following:atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3)." ::= { jnxpwAtmObjects 3 } jnxpwAtmInboundNto1Entry OBJECT-TYPE SYNTAX JnxPwAtmInboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all Read-Creat objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot." INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } ::= { jnxpwAtmInboundNto1Table 1 } JnxPwAtmInboundNto1Entry ::= SEQUENCE { jnxpwAtmInboundNto1AtmIf InterfaceIndex, jnxpwAtmInboundNto1Vpi AtmVpIdentifier, jnxpwAtmInboundNto1Vci AtmVcIdentifier, jnxpwAtmInboundNto1RowStatus RowStatus, jnxpwAtmInboundNto1TrafficParamDescr RowPointer, jnxpwAtmInboundNto1MappedVpi AtmVpIdentifier, jnxpwAtmInboundNto1MappedVci AtmVcIdentifier } jnxpwAtmInboundNto1AtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Interface that receives cells from the ATM network." ::= { jnxpwAtmInboundNto1Entry 1 } jnxpwAtmInboundNto1Vpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF." ::= { jnxpwAtmInboundNto1Entry 2 } jnxpwAtmInboundNto1Vci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF" ::= { jnxpwAtmInboundNto1Entry 3 } jnxpwAtmInboundNto1RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { jnxpwAtmInboundNto1Entry 4 } jnxpwAtmInboundNto1TrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort." ::= { jnxpwAtmInboundNto1Entry 5 } jnxpwAtmInboundNto1MappedVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active." ::= { jnxpwAtmInboundNto1Entry 6 } jnxpwAtmInboundNto1MappedVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active." ::= { jnxpwAtmInboundNto1Entry 7 } -- ATM PW Outbound Perf Table -- The following supplement the counters presented in the -- PW generic MIB -- ATM PW Performance Current Table. jnxpwAtmPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The current 15 minute interval counts are in this table. This table provides performance information per ATM PW." ::= { jnxpwAtmObjects 4 } jnxpwAtmPerfCurrentEntry OBJECT-TYPE SYNTAX JnxPwAtmPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwAtmPerfInterval table and the counts in this entry are reset to zero." INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } ::= { jnxpwAtmPerfCurrentTable 1 } JnxPwAtmPerfCurrentEntry ::= SEQUENCE { jnxpwAtmPerfCurrentMissingPkts PerfCurrentCount, jnxpwAtmPerfCurrentPktsReOrder PerfCurrentCount, jnxpwAtmPerfCurrentPktsMisOrder PerfCurrentCount, jnxpwAtmPerfCurrentPktsTimeout PerfCurrentCount, jnxpwAtmPerfCurrentPktsXmit Counter64, jnxpwAtmPerfCurrentCellsDropped PerfCurrentCount, jnxpwAtmPerfCurrentPktsReceived Counter64, jnxpwAtmPerfCurrentUnknownCells Counter64 } jnxpwAtmPerfCurrentMissingPkts OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { jnxpwAtmPerfCurrentEntry 1 } jnxpwAtmPerfCurrentPktsReOrder OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature." ::= { jnxpwAtmPerfCurrentEntry 2 } jnxpwAtmPerfCurrentPktsMisOrder OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order (via control word sequence numbers)." ::= { jnxpwAtmPerfCurrentEntry 3 } jnxpwAtmPerfCurrentPktsTimeout OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration while attempting to collect cells." ::= { jnxpwAtmPerfCurrentEntry 4 } jnxpwAtmPerfCurrentPktsXmit OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted packets." ::= { jnxpwAtmPerfCurrentEntry 5 } jnxpwAtmPerfCurrentCellsDropped OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { jnxpwAtmPerfCurrentEntry 6 } jnxpwAtmPerfCurrentPktsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets." ::= { jnxpwAtmPerfCurrentEntry 7 } jnxpwAtmPerfCurrentUnknownCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode." ::= { jnxpwAtmPerfCurrentEntry 8 } -- End ATM PW Performance Current Interval Table -- ATM PW Performance Interval Table. jnxpwAtmPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period. " ::= { jnxpwAtmObjects 5 } jnxpwAtmPerfIntervalEntry OBJECT-TYPE SYNTAX JnxPwAtmPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval. " INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwAtmPerfIntervalNumber } ::= { jnxpwAtmPerfIntervalTable 1 } JnxPwAtmPerfIntervalEntry ::= SEQUENCE { jnxpwAtmPerfIntervalNumber Unsigned32, jnxpwAtmPerfIntervalValidData TruthValue, jnxpwAtmPerfIntervalDuration Unsigned32, jnxpwAtmPerfIntervalMissingPkts PerfIntervalCount, jnxpwAtmPerfIntervalPktsReOrder PerfIntervalCount, jnxpwAtmPerfIntervalPktsMisOrder PerfIntervalCount, jnxpwAtmPerfIntervalPktsTimeout PerfIntervalCount, jnxpwAtmPerfIntervalPktsXmit Counter64, jnxpwAtmPerfIntervalCellsDropped PerfIntervalCount, jnxpwAtmPerfIntervalPktsReceived Counter64, jnxpwAtmPerfIntervalUnknownCells Counter64 } jnxpwAtmPerfIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 96." ::= { jnxpwAtmPerfIntervalEntry 1 } jnxpwAtmPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { jnxpwAtmPerfIntervalEntry 2 } jnxpwAtmPerfIntervalDuration OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { jnxpwAtmPerfIntervalEntry 3 } jnxpwAtmPerfIntervalMissingPkts OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { jnxpwAtmPerfIntervalEntry 4 } jnxpwAtmPerfIntervalPktsReOrder OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature." ::= { jnxpwAtmPerfIntervalEntry 5 } jnxpwAtmPerfIntervalPktsMisOrder OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order (via control word sequence numbers)." ::= { jnxpwAtmPerfIntervalEntry 6 } jnxpwAtmPerfIntervalPktsTimeout OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration." ::= { jnxpwAtmPerfIntervalEntry 7 } jnxpwAtmPerfIntervalPktsXmit OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted packets." ::= { jnxpwAtmPerfIntervalEntry 8 } jnxpwAtmPerfIntervalCellsDropped OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { jnxpwAtmPerfIntervalEntry 9 } jnxpwAtmPerfIntervalPktsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets." ::= { jnxpwAtmPerfIntervalEntry 10 } jnxpwAtmPerfIntervalUnknownCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode." ::= { jnxpwAtmPerfIntervalEntry 11 } -- End ATM PW Performance Interval Table -- ATM PW 1day Performance Table jnxpwAtmPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxPwAtmPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical 1 day intervals up to one full month." ::= { jnxpwAtmObjects 6 } jnxpwAtmPerf1DayIntervalEntry OBJECT-TYPE SYNTAX JnxPwAtmPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in this table by the agent for every entry in the pwAtmCfgTable table." INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwAtmPerf1DayIntervalNumber } ::= { jnxpwAtmPerf1DayIntervalTable 1 } JnxPwAtmPerf1DayIntervalEntry ::= SEQUENCE { jnxpwAtmPerf1DayIntervalNumber Unsigned32, jnxpwAtmPerf1DayIntervalValidData TruthValue, jnxpwAtmPerf1DayIntervalDuration Unsigned32, jnxpwAtmPerf1DayIntervalMissingPkts Counter32, jnxpwAtmPerf1DayIntervalPktsReOrder Counter32, jnxpwAtmPerf1DayIntervalPktsMisOrder Counter32, jnxpwAtmPerf1DayIntervalPktsTimeout Counter32, jnxpwAtmPerf1DayIntervalPktsXmit Counter64, jnxpwAtmPerf1DayIntervalCellsDropped Counter32, jnxpwAtmPerf1DayIntervalPktsReceived Counter64, jnxpwAtmPerf1DayIntervalUnknownCells Counter64 } jnxpwAtmPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..365) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively" ::= { jnxpwAtmPerf1DayIntervalEntry 1 } jnxpwAtmPerf1DayIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if the data for this interval is valid." ::= { jnxpwAtmPerf1DayIntervalEntry 2 } jnxpwAtmPerf1DayIntervalDuration OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { jnxpwAtmPerf1DayIntervalEntry 3 } jnxpwAtmPerf1DayIntervalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { jnxpwAtmPerf1DayIntervalEntry 4 } jnxpwAtmPerf1DayIntervalPktsReOrder OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature." ::= { jnxpwAtmPerf1DayIntervalEntry 5 } jnxpwAtmPerf1DayIntervalPktsMisOrder OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered." ::= { jnxpwAtmPerf1DayIntervalEntry 6 } jnxpwAtmPerf1DayIntervalPktsTimeout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration." ::= { jnxpwAtmPerf1DayIntervalEntry 7 } jnxpwAtmPerf1DayIntervalPktsXmit OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted packets." ::= { jnxpwAtmPerf1DayIntervalEntry 8 } jnxpwAtmPerf1DayIntervalCellsDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { jnxpwAtmPerf1DayIntervalEntry 9 } jnxpwAtmPerf1DayIntervalPktsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets." ::= { jnxpwAtmPerf1DayIntervalEntry 10 } jnxpwAtmPerf1DayIntervalUnknownCells OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI value. This object is relevant only in N:1 mode." ::= { jnxpwAtmPerf1DayIntervalEntry 11 } -- End of ATM PW Performance table END