ALCATEL-IND1-IPV6-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Unsigned32, Counter32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, PhysAddress, RowStatus, DisplayString, TimeStamp, TruthValue, DateAndTime FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF Ipv6Address, Ipv6IfIndexOrZero FROM IPV6-TC softentIND1Ipv6 FROM ALCATEL-IND1-BASE ipv6IfIndex, ipv6RouteEntry FROM IPV6-MIB; alcatelIND1IPv6MIB MODULE-IDENTITY LAST-UPDATED "200807240000Z" ORGANIZATION "Alcatel-Lucent" CONTACT-INFO "Please consult with Customer Service to ensure the most appropriate version of this document is used with the products in question: Alcatel-Lucent, Enterprise Solutions Division (Formerly Alcatel Internetworking, Incorporated) 26801 West Agoura Road Agoura Hills, CA 91301-5122 United States Of America Telephone: North America +1 800 995 2696 Latin America +1 877 919 9526 Europe +31 23 556 0100 Asia +65 394 7933 All Other +1 818 878 4507 Electronic Mail: support@ind.alcatel.com World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs" DESCRIPTION "This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2008 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE" REVISION "200807240000Z" DESCRIPTION "The latest version of this MIB Module." ::= { softentIND1Ipv6 1 } alcatelIND1IPv6MIBObjects OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIB 1 } AlaIPv6AddressPrefix ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x:" STATUS current DESCRIPTION "A data type for the 8 byte IPv6 prefixes for EUI-64 addresses" SYNTAX OCTET STRING (SIZE (8)) -- -- Alcatel IPv6 Configuration -- alaIPv6Config OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIBObjects 1 } alaIPv6ClearNeighbors OBJECT-TYPE SYNTAX INTEGER { clear(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear all non-static entries from the Neighbor table." ::= { alaIPv6Config 1 } alaIPv6ClearTraffic OBJECT-TYPE SYNTAX INTEGER { clear(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reset all IPv6 traffic counters." ::= { alaIPv6Config 2 } alaIPv6ClearPMTUTable OBJECT-TYPE SYNTAX INTEGER { clear(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the path MTU table." ::= { alaIPv6Config 3 } alaIPv6PMTUMinLifetime OBJECT-TYPE SYNTAX Unsigned32 (10..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "Set the minimum lifetime for entries in the path MTU table." DEFVAL { 60 } ::= { alaIPv6Config 4 } alaIPv6NeighborStaleLifetime OBJECT-TYPE SYNTAX Unsigned32 (5..2880) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "Set the minimum lifetime for neighbor entries in the stale state." DEFVAL { 1440 } ::= { alaIPv6Config 5 } alaIPv6GlobalID OBJECT-TYPE SYNTAX OCTET STRING (SIZE(5)) MAX-ACCESS read-write STATUS current DESCRIPTION "The global ID used in the creation of local IPv6 unicast addresses (RFC 4193). An explicit value may be specified for the global ID or this object may be set to all zero to have a global ID be created based on the algorithm from the RFC." ::= { alaIPv6Config 6 } -- -- Alcatel IPv6 Interface Table -- alaIPv6InterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6InterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the creation and removal of IPv6 interfaces. The table is indexed by ipv6IfIndex. The value of ipv6IfIndex shall be a four byte value in one of the following formats: 0x0000vvvv - The interface for VLAN vvvv 0x0100tttt - The interface for tunnel tttt 0x02000001 - The IPv6 loopback interface The loopback interface configuration cannot be modified." ::= { alcatelIND1IPv6MIBObjects 2 } alaIPv6InterfaceEntry OBJECT-TYPE SYNTAX AlaIPv6InterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 interface entry." INDEX { ipv6IfIndex } ::= { alaIPv6InterfaceTable 1 } AlaIPv6InterfaceEntry ::= SEQUENCE { alaIPv6InterfaceRowStatus RowStatus, alaIPv6InterfaceDescription DisplayString, alaIPv6InterfaceMtu Unsigned32, alaIPv6InterfaceType INTEGER, alaIPv6InterfaceAdminStatus INTEGER, alaIPv6InterfaceSendRouterAdvertisements INTEGER, alaIPv6InterfaceMaxRtrAdvInterval Unsigned32, alaIPv6InterfaceAdvManagedFlag TruthValue, alaIPv6InterfaceAdvOtherConfigFlag TruthValue, alaIPv6InterfaceAdvReachableTime Unsigned32, alaIPv6InterfaceAdvRetransTimer Unsigned32, alaIPv6InterfaceAdvDefaultLifetime Unsigned32, alaIPv6InterfaceName DisplayString, alaIPv6InterfaceAdvSendMtu TruthValue, alaIPv6InterfaceReachableTime Unsigned32, alaIPv6InterfaceBaseReachableTime Unsigned32, alaIPv6InterfaceMinRtrAdvInterval Unsigned32, alaIPv6InterfaceClockSkew Unsigned32, alaIPv6InterfaceRetransTimer Unsigned32, alaIPv6InterfaceDADTransmits Unsigned32, alaIPv6InterfaceAdvHopLimit Unsigned32 } alaIPv6InterfaceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of IPv6 interfaces." ::= { alaIPv6InterfaceEntry 1 } alaIPv6InterfaceDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 interface's description." ::= { alaIPv6InterfaceEntry 2 } alaIPv6InterfaceMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 interface's maximum transmission unit." ::= { alaIPv6InterfaceEntry 3 } alaIPv6InterfaceType OBJECT-TYPE SYNTAX INTEGER { other(1), vlan(2), tunnel(3), loopback(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The interface type." ::= { alaIPv6InterfaceEntry 4 } alaIPv6InterfaceAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Interface administrative status." ::= { alaIPv6InterfaceEntry 5 } alaIPv6InterfaceSendRouterAdvertisements OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is enable(1). Some interface types (e.g. 6to4 tunnel) cannot send router advertisements so the default (and only) value for those interfaces is disable(2)." DEFVAL {enable} ::= { alaIPv6InterfaceEntry 6 } alaIPv6InterfaceMaxRtrAdvInterval OBJECT-TYPE SYNTAX Unsigned32 (4..1800) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum time allowed between sending unsolicited multicast router advertisements from the interface." DEFVAL {600} ::= { alaIPv6InterfaceEntry 7 } alaIPv6InterfaceAdvManagedFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements." DEFVAL { false } ::= { alaIPv6InterfaceEntry 8 } alaIPv6InterfaceAdvOtherConfigFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements." DEFVAL { false } ::= { alaIPv6InterfaceEntry 9 } alaIPv6InterfaceAdvReachableTime OBJECT-TYPE SYNTAX Unsigned32 (0..3600000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router." DEFVAL {0} ::= { alaIPv6InterfaceEntry 10 } alaIPv6InterfaceAdvRetransTimer OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router." DEFVAL {0} ::= { alaIPv6InterfaceEntry 11 } alaIPv6InterfaceAdvDefaultLifetime OBJECT-TYPE SYNTAX Unsigned32 (0..9000) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds. The special value zero indicates that the router is not to be used as a default router. The special value 1 indicates that this object's true value should be computed using the formula 3 * alaIPv6InterfaceMaxRtrAdvInterval." DEFVAL {1} ::= { alaIPv6InterfaceEntry 12 } alaIPv6InterfaceName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..20)) MAX-ACCESS read-create STATUS current DESCRIPTION "The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically assigned." ::= { alaIPv6InterfaceEntry 13 } alaIPv6InterfaceAdvSendMtu OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements." DEFVAL { false } ::= { alaIPv6InterfaceEntry 14 } alaIPv6InterfaceReachableTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioning to the stale state. Computed to be between .5 and 1.5 times the alaIPv6InterfaceBaseReachableTime." ::= { alaIPv6InterfaceEntry 15 } alaIPv6InterfaceBaseReachableTime OBJECT-TYPE SYNTAX Unsigned32 (10..3600) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above." ::= { alaIPv6InterfaceEntry 16 } alaIPv6InterfaceMinRtrAdvInterval OBJECT-TYPE SYNTAX Unsigned32 (0..1350) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more than .75 times the value of alaIPv6InterfaceMaxRtrAdvInterval. Setting this object to the special value of 0 indicates that the minimum interval should be automatically recalculated using the formula .33 times the value of alaIPv6InterfaceMaxRtrAdvInterval." DEFVAL {0} ::= { alaIPv6InterfaceEntry 17 } alaIPv6InterfaceClockSkew OBJECT-TYPE SYNTAX Unsigned32 (0..3600) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly synchronized clocks." DEFVAL { 600 } ::= { alaIPv6InterfaceEntry 18 } alaIPv6InterfaceRetransTimer OBJECT-TYPE SYNTAX Unsigned32 (1000..30000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery." DEFVAL { 1000 } ::= { alaIPv6InterfaceEntry 19 } alaIPv6InterfaceDADTransmits OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Neighbor Solicitations to send during Duplicate Address Detection." DEFVAL { 1 } ::= { alaIPv6InterfaceEntry 20 } alaIPv6InterfaceAdvHopLimit OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The value placed in the current hop limit field of router advertisements." DEFVAL { 64 } ::= { alaIPv6InterfaceEntry 21 } -- -- Alcatel IPv6 Tunnel Configuration -- alaIPv6TunnelConfig OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIBObjects 3 } alaIPv6ConfigTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6ConfigTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IPv6 configured tunnels. This table contains the tunnel-specific information extending the corresponding tunnel interface entry in alaIPv6InterfaceTable." ::= { alaIPv6TunnelConfig 2 } alaIPv6ConfigTunnelEntry OBJECT-TYPE SYNTAX AlaIPv6ConfigTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry contains the objects for an IPv6 configured tunnel." INDEX { ipv6IfIndex } ::= { alaIPv6ConfigTunnelTable 1 } AlaIPv6ConfigTunnelEntry ::= SEQUENCE { alaIPv6ConfigTunnelV4Source IpAddress, alaIPv6ConfigTunnelV4Dest IpAddress } alaIPv6ConfigTunnelV4Source OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The source IPv4 address for the tunnel." ::= { alaIPv6ConfigTunnelEntry 1 } alaIPv6ConfigTunnelV4Dest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The destination IPv4 address for the tunnel." ::= { alaIPv6ConfigTunnelEntry 2 } -- -- Alcatel IPv6 Interface Address Table -- alaIPv6InterfaceAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6InterfaceAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the creation and removal of IPv6 addresses assigned to interfaces." ::= { alcatelIND1IPv6MIBObjects 4 } alaIPv6InterfaceAddressEntry OBJECT-TYPE SYNTAX AlaIPv6InterfaceAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 interface address entry. The same link-local address may be assigned to multiple interfaces. A global address may only be assigned to a single interface." INDEX { ipv6IfIndex, alaIPv6InterfaceAddress } ::= { alaIPv6InterfaceAddressTable 1 } AlaIPv6InterfaceAddressEntry ::= SEQUENCE { alaIPv6InterfaceAddressRowStatus RowStatus, alaIPv6InterfaceAddress Ipv6Address, alaIPv6InterfaceAddressPrefixLength Unsigned32, alaIPv6InterfaceAddressAnycastFlag TruthValue, alaIPv6InterfaceAddressDADStatus INTEGER } alaIPv6InterfaceAddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of IPv6 interface addresses." ::= { alaIPv6InterfaceAddressEntry 1 } alaIPv6InterfaceAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface." ::= { alaIPv6InterfaceAddressEntry 2 } alaIPv6InterfaceAddressPrefixLength OBJECT-TYPE SYNTAX Unsigned32 (3..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of bits that are significant in the IPv6 address' prefix." ::= { alaIPv6InterfaceAddressEntry 3 } alaIPv6InterfaceAddressAnycastFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise." DEFVAL { false } ::= { alaIPv6InterfaceAddressEntry 4 } alaIPv6InterfaceAddressDADStatus OBJECT-TYPE SYNTAX INTEGER { unknown(0), pending(1), duplicate(2), passed(3), check(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such cases, duplicate address detection will be performed again for the address." ::= { alaIPv6InterfaceAddressEntry 5 } -- -- Alcatel IPv6 EUI64 Interface Address Table -- alaIPv6InterfaceEUI64AddressTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6InterfaceEUI64AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the creation and removal of IPv6 addresses formed by appending an EUI-64 interface identifier to the specified prefix. This table is mainly used for the creation of such addresses. After creation they can be managed via the alaIPv6InterfaceAddressTable." ::= { alcatelIND1IPv6MIBObjects 5 } alaIPv6InterfaceEUI64AddressEntry OBJECT-TYPE SYNTAX AlaIPv6InterfaceEUI64AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 interface EUI-64 address entry." INDEX { ipv6IfIndex, alaIPv6InterfaceEUI64AddressPrefix } ::= { alaIPv6InterfaceEUI64AddressTable 1 } AlaIPv6InterfaceEUI64AddressEntry ::= SEQUENCE { alaIPv6InterfaceEUI64AddressRowStatus RowStatus, alaIPv6InterfaceEUI64AddressPrefix AlaIPv6AddressPrefix, alaIPv6InterfaceEUI64AddressPrefixLength Unsigned32, alaIPv6InterfaceEUI64AddressIdentifier OCTET STRING } alaIPv6InterfaceEUI64AddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of IPv6 interface EUI-64 addresses." ::= { alaIPv6InterfaceEUI64AddressEntry 1 } alaIPv6InterfaceEUI64AddressPrefix OBJECT-TYPE SYNTAX AlaIPv6AddressPrefix MAX-ACCESS not-accessible STATUS current DESCRIPTION "The prefix for the EUI-64 address." ::= { alaIPv6InterfaceEUI64AddressEntry 2 } alaIPv6InterfaceEUI64AddressPrefixLength OBJECT-TYPE SYNTAX Unsigned32 (3..64) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of bits that are significant in the IPv6 address' prefix." ::= { alaIPv6InterfaceEUI64AddressEntry 3 } alaIPv6InterfaceEUI64AddressIdentifier OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address." ::= { alaIPv6InterfaceEUI64AddressEntry 4 } -- -- Alcatel IPv6 Neighbor Table. -- alaIPv6NeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPv6 neighbor table. Much of this information is available in the RFC-2465 ipv6NetToMediaTable. However, that table does not allow the static configuration of neighbor entries (all objects except for ipv6NetToMediaValid are read-only)." ::= { alcatelIND1IPv6MIBObjects 6 } alaIPv6NeighborEntry OBJECT-TYPE SYNTAX AlaIPv6NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one IPv6 address to `physical' address equivalence (a neighbor)." INDEX { ipv6IfIndex, alaIPv6NeighborNetAddress } ::= { alaIPv6NeighborTable 1 } AlaIPv6NeighborEntry ::= SEQUENCE { alaIPv6NeighborNetAddress Ipv6Address, alaIPv6NeighborPhysAddress PhysAddress, alaIPv6NeighborSlot Unsigned32, alaIPv6NeighborPort Unsigned32, alaIPv6NeighborType INTEGER, alaIPv6NeighborState INTEGER, alaIPv6NeighborLastUpdated TimeStamp, alaIPv6NeighborRowStatus RowStatus, alaIPv6NeighborLifetime Unsigned32, alaIPv6NeighborReachability INTEGER } alaIPv6NeighborNetAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "The neighbor's IPv6 Address." ::= { alaIPv6NeighborEntry 1 } alaIPv6NeighborPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The neighbor's media-dependent `physical' address." ::= { alaIPv6NeighborEntry 2 } alaIPv6NeighborSlot OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not applicable." ::= { alaIPv6NeighborEntry 3 } alaIPv6NeighborPort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not applicable." ::= { alaIPv6NeighborEntry 4 } alaIPv6NeighborType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following dynamic(2), -- dynamically resolved static(3), -- statically configured local(4) -- local interface } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. All entries added via this table will have the type static(3) and only static entries may be removed via this table." ::= { alaIPv6NeighborEntry 5 } alaIPv6NeighborState OBJECT-TYPE SYNTAX INTEGER { reachable(1), -- confirmed reachability stale(2), -- unconfirmed reachability delay(3), -- waiting for reachability -- confirmation before entering -- the probe state probe(4), -- actively probing invalid(5), -- an invalidated mapping unknown(6) -- state can not be determined -- for some reason. } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used." ::= { alaIPv6NeighborEntry 6 } alaIPv6NeighborLastUpdated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { alaIPv6NeighborEntry 7 } alaIPv6NeighborRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of static entries in the neighbor table." ::= { alaIPv6NeighborEntry 8 } alaIPv6NeighborLifetime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero indicates the neighbor will remain in its current state indefinitely." ::= { alaIPv6NeighborEntry 9 } alaIPv6NeighborReachability OBJECT-TYPE SYNTAX INTEGER { confirmed(1), -- confirmed reachability unconfirmed(2), -- unconfirmed reachability incomplete(3) -- detection incomplete } MAX-ACCESS read-only STATUS current DESCRIPTION "The reachability status of the neighbor." ::= { alaIPv6NeighborEntry 10 } -- -- Alcatel IPv6 Static Routes Table -- alaIPv6StaticRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6StaticRouteEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "This table has been superseded by alaIprmV6StaticRouteTable in ALCATEL-IND1-IPRMV6-MIB. Table allowing the creation and removal of static IPv6 routes." ::= { alcatelIND1IPv6MIBObjects 7 } alaIPv6StaticRouteEntry OBJECT-TYPE SYNTAX AlaIPv6StaticRouteEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A static route entry." INDEX { alaIPv6StaticRouteDest, alaIPv6StaticRoutePfxLength } ::= { alaIPv6StaticRouteTable 1 } AlaIPv6StaticRouteEntry ::= SEQUENCE { alaIPv6StaticRouteDest Ipv6Address, alaIPv6StaticRoutePfxLength INTEGER, alaIPv6StaticRouteIfIndex Ipv6IfIndexOrZero, alaIPv6StaticRouteNextHop Ipv6Address, alaIPv6StaticRouteMetric Unsigned32, alaIPv6StaticRouteRowStatus RowStatus } alaIPv6StaticRouteDest OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "The destination IPv6 address of this static route. This object may not take a Multicast address value." ::= { alaIPv6StaticRouteEntry 1 } alaIPv6StaticRoutePfxLength OBJECT-TYPE SYNTAX INTEGER(0..128) MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Indicates the prefix length of the destination address." ::= { alaIPv6StaticRouteEntry 2 } alaIPv6StaticRouteIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndexOrZero MAX-ACCESS read-create STATUS obsolete DESCRIPTION "If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop address types the value is zero." DEFVAL { 0 } ::= { alaIPv6StaticRouteEntry 3 } alaIPv6StaticRouteNextHop OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The IPv6 address of the next hop towards the destination." ::= { alaIPv6StaticRouteEntry 4 } alaIPv6StaticRouteMetric OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The routing metric for this route. The lower the value, the higher the priority for the static route." DEFVAL { 1 } ::= { alaIPv6StaticRouteEntry 5 } alaIPv6StaticRouteRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Used to control the addition and removal of static routes." ::= { alaIPv6StaticRouteEntry 6 } -- -- Local host name to IPv6 address table -- alaIPv6HostTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Local table mapping host names to IPv6 addresses. This provides the equivalent of /etc/hosts for IPv6." ::= { alcatelIND1IPv6MIBObjects 8 } alaIPv6HostEntry OBJECT-TYPE SYNTAX AlaIPv6HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry maps a host name to an IPv6 address." INDEX { alaIPv6HostName, alaIPv6HostAddress } ::= { alaIPv6HostTable 1 } AlaIPv6HostEntry ::= SEQUENCE { alaIPv6HostName DisplayString, alaIPv6HostAddress Ipv6Address, alaIPv6HostRowStatus RowStatus } alaIPv6HostName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A host name to be mapped to an IPv6 address." ::= { alaIPv6HostEntry 1 } alaIPv6HostAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPv6 address mapped to the host name." ::= { alaIPv6HostEntry 2 } alaIPv6HostRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Allows host name/IPv6 address mappings to be created and deleted in this table." ::= { alaIPv6HostEntry 3 } -- -- Alcatel IPv6 Interface Prefix Table for Router Advertisements -- alaIPv6InterfacePrefixTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6InterfacePrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the creation and removal of IPv6 prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. Default: all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent. The link-local prefix is not included in the list of advertised prefixes." ::= { alcatelIND1IPv6MIBObjects 9 } alaIPv6InterfacePrefixEntry OBJECT-TYPE SYNTAX AlaIPv6InterfacePrefixEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 interface prefix entry." INDEX { ipv6IfIndex, alaIPv6InterfacePrefix, alaIPv6InterfacePrefixLength } ::= { alaIPv6InterfacePrefixTable 1 } AlaIPv6InterfacePrefixEntry ::= SEQUENCE { alaIPv6InterfacePrefixRowStatus RowStatus, alaIPv6InterfacePrefix Ipv6Address, alaIPv6InterfacePrefixLength Unsigned32, alaIPv6InterfacePrefixValidLifetime Unsigned32, alaIPv6InterfacePrefixOnLinkFlag TruthValue, alaIPv6InterfacePrefixPreferredLifetime Unsigned32, alaIPv6InterfacePrefixAutonomousFlag TruthValue, alaIPv6InterfacePrefixSource INTEGER, alaIPv6InterfacePrefixValidLifetimeDecrement TruthValue, alaIPv6InterfacePrefixValidLifetimeExpire DateAndTime, alaIPv6InterfacePrefixPreferredLifetimeDecrement TruthValue, alaIPv6InterfacePrefixPreferredLifetimeExpire DateAndTime } alaIPv6InterfacePrefixRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages." ::= { alaIPv6InterfacePrefixEntry 1 } alaIPv6InterfacePrefix OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "The prefix associated with this interface." ::= { alaIPv6InterfacePrefixEntry 2 } alaIPv6InterfacePrefixLength OBJECT-TYPE SYNTAX Unsigned32 (1..127) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length of the prefix in bits." ::= { alaIPv6InterfacePrefixEntry 3 } alaIPv6InterfacePrefixValidLifetime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity." DEFVAL { 2592000 } ::= { alaIPv6InterfacePrefixEntry 4 } alaIPv6InterfacePrefixOnLinkFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the on-link flag (L-bit) field in the Prefix Information option." DEFVAL { true } ::= { alaIPv6InterfacePrefixEntry 5 } alaIPv6InterfacePrefixPreferredLifetime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity." DEFVAL { 604800 } ::= { alaIPv6InterfacePrefixEntry 6 } alaIPv6InterfacePrefixAutonomousFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The value to be placed in the Autonomous Flag field in the Prefix Information option." DEFVAL { true } ::= { alaIPv6InterfacePrefixEntry 7 } alaIPv6InterfacePrefixSource OBJECT-TYPE SYNTAX INTEGER { other(1), dynamic(2), configured(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration the value will be dynamic(2)." ::= { alaIPv6InterfacePrefixEntry 8 } alaIPv6InterfacePrefixValidLifetimeDecrement OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixValidLifetime." DEFVAL { false } ::= { alaIPv6InterfacePrefixEntry 9 } alaIPv6InterfacePrefixValidLifetimeExpire OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-create STATUS current DESCRIPTION "The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true." ::= { alaIPv6InterfacePrefixEntry 10 } alaIPv6InterfacePrefixPreferredLifetimeDecrement OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixPreferredLifetime." DEFVAL { false } ::= { alaIPv6InterfacePrefixEntry 11 } alaIPv6InterfacePrefixPreferredLifetimeExpire OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-create STATUS current DESCRIPTION "The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true." ::= { alaIPv6InterfacePrefixEntry 12 } -- -- Alcatel IPv6 path MTU table -- alaIPv6PMTUTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6PMTUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the retrieval of the known IPv6 path MTU value." ::= { alcatelIND1IPv6MIBObjects 10 } alaIPv6PMTUEntry OBJECT-TYPE SYNTAX AlaIPv6PMTUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPv6 path MTU entry." INDEX { alaIPv6PMTUDest } ::= { alaIPv6PMTUTable 1 } AlaIPv6PMTUEntry ::= SEQUENCE { alaIPv6PMTUDest Ipv6Address, alaIPv6PMTU Unsigned32, alaIPv6PMTUExpire Unsigned32, alaIPv6PMTUHits Counter32, alaIPv6PMTUUpdates Counter32 } alaIPv6PMTUDest OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination address of the IPv6 path." ::= { alaIPv6PMTUEntry 1 } alaIPv6PMTU OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path's MTU." ::= { alaIPv6PMTUEntry 2 } alaIPv6PMTUExpire OBJECT-TYPE SYNTAX Unsigned32 UNITS "minutes" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the PMTU entry is removed from the table." ::= { alaIPv6PMTUEntry 3 } alaIPv6PMTUHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the path MTU entry has been used." ::= { alaIPv6PMTUEntry 4 } alaIPv6PMTUUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the path MTU entry has been updated." ::= { alaIPv6PMTUEntry 5 } -- -- Alcatel IPv6 route flags table -- alaIPv6RouteFlagsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6RouteFlagsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the retrieval of the flags for IPv6 route entries." ::= { alcatelIND1IPv6MIBObjects 11 } alaIPv6RouteFlagsEntry OBJECT-TYPE SYNTAX AlaIPv6RouteFlagsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IPV6 route flags entry." AUGMENTS { ipv6RouteEntry } ::= { alaIPv6RouteFlagsTable 1 } AlaIPv6RouteFlagsEntry ::= SEQUENCE { alaIPv6RouteFlagsUp TruthValue, alaIPv6RouteFlagsGateway TruthValue, alaIPv6RouteFlagsHost TruthValue, alaIPv6RouteFlagsStatic TruthValue, alaIPv6RouteFlagsCloneable TruthValue, alaIPv6RouteFlagsDiscard TruthValue, alaIPv6RouteFlagsECMP TruthValue } alaIPv6RouteFlagsUp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Up (U) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 1 } alaIPv6RouteFlagsGateway OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Gateway (G) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 2 } alaIPv6RouteFlagsHost OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Host (H) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 3 } alaIPv6RouteFlagsStatic OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Static (S) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 4 } alaIPv6RouteFlagsCloneable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Cloneable (C) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 5 } alaIPv6RouteFlagsDiscard OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the Discard/Blackhole (B) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 6 } alaIPv6RouteFlagsECMP OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the ECMP (E) flag is set on the route." ::= { alaIPv6RouteFlagsEntry 7 } -- -- Alcatel IPv6 Local Unicast Address Table -- alaIPv6LocalUnicastTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaIPv6LocalUnicastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table allowing the creation and removal of local IPv6 unicast addresses (RFC 4193) on an interface." ::= { alcatelIND1IPv6MIBObjects 13 } alaIPv6LocalUnicastEntry OBJECT-TYPE SYNTAX AlaIPv6LocalUnicastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An local unicast IPv6 address entry." INDEX { ipv6IfIndex, alaIPv6LocalUnicastGlobalID, alaIPv6LocalUnicastSubnetID, alaIPv6LocalUnicastInterfaceID } ::= { alaIPv6LocalUnicastTable 1 } AlaIPv6LocalUnicastEntry ::= SEQUENCE { alaIPv6LocalUnicastGlobalID OCTET STRING, alaIPv6LocalUnicastSubnetID OCTET STRING, alaIPv6LocalUnicastInterfaceID OCTET STRING, alaIPv6LocalUnicastPrefixLength Unsigned32, alaIPv6LocalUnicastEUI64 TruthValue, alaIPv6LocalUnicastRowStatus RowStatus } alaIPv6LocalUnicastGlobalID OBJECT-TYPE SYNTAX OCTET STRING (SIZE(5)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value." ::= { alaIPv6LocalUnicastEntry 1 } alaIPv6LocalUnicastSubnetID OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subnet ID portion of the local IPv6 unicast address." ::= { alaIPv6LocalUnicastEntry 2 } alaIPv6LocalUnicastInterfaceID OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero." ::= { alaIPv6LocalUnicastEntry 3 } alaIPv6LocalUnicastPrefixLength OBJECT-TYPE SYNTAX Unsigned32 (64..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of bits that are significant in the IPv6 address prefix." DEFVAL { 64 } ::= { alaIPv6LocalUnicastEntry 4 } alaIPv6LocalUnicastEUI64 OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true(1) the interface identifier is formed from an automatically generated EUI-64 value." DEFVAL { false } ::= { alaIPv6LocalUnicastEntry 5 } alaIPv6LocalUnicastRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to control the addition and removal of local IPv6 unicast addresses." ::= { alaIPv6LocalUnicastEntry 6 } -- -- conformance information -- alcatelIND1IPv6MIBConformance OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIB 2 } alcatelIND1IPv6MIBCompliances OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIBConformance 1 } alcatelIND1IPv6MIBGroups OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIBConformance 2 } alaIPv6Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for switches with Alcatel IPv6 stack and implementing ALCATEL-IND1-IPV6-MIB." MODULE MANDATORY-GROUPS { alaIPv6TunnelConfigGroup, alaIPv6ConfigGroup, alaIPv6NeighborGroup, alaIPv6StaticRouteGroup, alaIPv6InterfaceGroup, alaIPv6InterfaceAddressGroup, alaIPv6InterfaceEUI64AddressGroup, alaIPv6InterfacePrefixGroup, alaIPv6PMTUGroup, alaIPv6RouteFlagsGroup, alaIPv6LocalUnicastGroup } ::= { alcatelIND1IPv6MIBCompliances 1 } -- -- units of conformance -- alaIPv6TunnelConfigGroup OBJECT-GROUP OBJECTS { alaIPv6ConfigTunnelV4Source, alaIPv6ConfigTunnelV4Dest } STATUS current DESCRIPTION "A collection of objects to support management of Alcatel IPv6 tunneling." ::= { alcatelIND1IPv6MIBGroups 1 } alaIPv6ConfigGroup OBJECT-GROUP OBJECTS { alaIPv6ClearNeighbors, alaIPv6ClearTraffic, alaIPv6ClearPMTUTable, alaIPv6PMTUMinLifetime, alaIPv6NeighborStaleLifetime, alaIPv6GlobalID } STATUS current DESCRIPTION "A collection of objects to support management of configuration parameters of Alcatel IPv6 stack." ::= { alcatelIND1IPv6MIBGroups 2 } alaIPv6NeighborGroup OBJECT-GROUP OBJECTS { -- alaIPv6NeighborNetAddress, alaIPv6NeighborPhysAddress, alaIPv6NeighborSlot, alaIPv6NeighborPort, alaIPv6NeighborType, -- alaIPv6NeighborState, alaIPv6NeighborLastUpdated, alaIPv6NeighborRowStatus, alaIPv6NeighborLifetime, alaIPv6NeighborReachability } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 neighbors." ::= { alcatelIND1IPv6MIBGroups 3 } alaIPv6StaticRouteGroup OBJECT-GROUP OBJECTS { -- alaIPv6StaticRouteDest, -- alaIPv6StaticRoutePfxLength, alaIPv6StaticRouteIfIndex, alaIPv6StaticRouteNextHop, alaIPv6StaticRouteMetric, alaIPv6StaticRouteRowStatus } STATUS obsolete DESCRIPTION "A collection of objects to support management of IPv6 static routes." ::= { alcatelIND1IPv6MIBGroups 4 } alaIPv6InterfaceGroup OBJECT-GROUP OBJECTS { alaIPv6InterfaceRowStatus, alaIPv6InterfaceDescription, alaIPv6InterfaceMtu, alaIPv6InterfaceType, alaIPv6InterfaceAdminStatus, alaIPv6InterfaceSendRouterAdvertisements, alaIPv6InterfaceMaxRtrAdvInterval, alaIPv6InterfaceAdvManagedFlag, alaIPv6InterfaceAdvOtherConfigFlag, alaIPv6InterfaceAdvReachableTime, alaIPv6InterfaceAdvRetransTimer, alaIPv6InterfaceAdvDefaultLifetime, alaIPv6InterfaceName, alaIPv6InterfaceReachableTime, alaIPv6InterfaceBaseReachableTime, alaIPv6InterfaceMinRtrAdvInterval, alaIPv6InterfaceClockSkew, alaIPv6InterfaceRetransTimer, alaIPv6InterfaceDADTransmits, alaIPv6InterfaceAdvHopLimit } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 interfaces." ::= { alcatelIND1IPv6MIBGroups 5 } alaIPv6InterfaceAddressGroup OBJECT-GROUP OBJECTS { alaIPv6InterfaceAddressRowStatus, -- alaIPv6InterfaceAddress, alaIPv6InterfaceAddressPrefixLength, alaIPv6InterfaceAddressAnycastFlag } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 addresses assigned to interfaces." ::= { alcatelIND1IPv6MIBGroups 6 } alaIPv6InterfaceEUI64AddressGroup OBJECT-GROUP OBJECTS { alaIPv6InterfaceEUI64AddressRowStatus, -- alaIPv6InterfaceEUI64AddressPrefix, alaIPv6InterfaceEUI64AddressPrefixLength, alaIPv6InterfaceEUI64AddressIdentifier } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 EUI-64 addresses assigned to interfaces." ::= { alcatelIND1IPv6MIBGroups 7 } alaIPv6InterfacePrefixGroup OBJECT-GROUP OBJECTS { alaIPv6InterfacePrefixRowStatus, -- alaIPv6InterfacePrefix, -- alaIPv6InterfacePrefixLength, alaIPv6InterfacePrefixValidLifetime, alaIPv6InterfacePrefixOnLinkFlag, alaIPv6InterfacePrefixPreferredLifetime, alaIPv6InterfacePrefixAutonomousFlag, alaIPv6InterfacePrefixSource, alaIPv6InterfacePrefixValidLifetimeDecrement, alaIPv6InterfacePrefixValidLifetimeExpire, alaIPv6InterfacePrefixPreferredLifetimeDecrement, alaIPv6InterfacePrefixPreferredLifetimeExpire } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 prefixes assigned to interfaces." ::= { alcatelIND1IPv6MIBGroups 8 } alaIPv6PMTUGroup OBJECT-GROUP OBJECTS { -- alaIPv6PMTUDest, alaIPv6PMTU, alaIPv6PMTUExpire, alaIPv6PMTUHits, alaIPv6PMTUUpdates } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 path MTUs." ::= { alcatelIND1IPv6MIBGroups 9 } alaIPv6RouteFlagsGroup OBJECT-GROUP OBJECTS { alaIPv6RouteFlagsUp, alaIPv6RouteFlagsGateway, alaIPv6RouteFlagsHost, alaIPv6RouteFlagsStatic, alaIPv6RouteFlagsCloneable, alaIPv6RouteFlagsDiscard, alaIPv6RouteFlagsECMP } STATUS current DESCRIPTION "A collection of objects to support management of IPv6 route flags." ::= { alcatelIND1IPv6MIBGroups 10 } alaIPv6LocalUnicastGroup OBJECT-GROUP OBJECTS { -- alaIPv6LocalUnicastGlobalID, -- alaIPv6LocalUnicastSubnetID, -- alaIPv6LocalUnicastInterfaceID, alaIPv6LocalUnicastPrefixLength, alaIPv6LocalUnicastEUI64, alaIPv6LocalUnicastRowStatus } STATUS current DESCRIPTION "A collection of objects to support management of local IPv6 unicast addresses (RFC 4193)." ::= { alcatelIND1IPv6MIBGroups 11 } -- -- Traps in case if Maximum hardware table entries is reached -- alcatelIND1IPv6Traps OBJECT IDENTIFIER ::= { alcatelIND1IPv6MIBObjects 12} alcatelIND1IPv6TrapsRoot OBJECT IDENTIFIER ::= { alcatelIND1IPv6Traps 0} ndpMaxLimitReached NOTIFICATION-TYPE STATUS current DESCRIPTION " This notification is generated when hardware table has reached supported Maximum entries. OS6400 will not generate new ARP request for new nexthops" ::= {alcatelIND1IPv6TrapsRoot 1} END