ALCATEL-IND1-PIM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress, Integer32, TimeTicks, Unsigned32, Counter32 FROM SNMPv2-SMI InetAddressType, InetAddress, InetAddressPrefixLength FROM INET-ADDRESS-MIB pimInterfaceEntry FROM PIM-STD-MIB RowStatus, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF routingIND1Pim FROM ALCATEL-IND1-BASE; alcatelIND1PIMMIB MODULE-IDENTITY LAST-UPDATED "201505280000Z" ORGANIZATION "Alcatel-Lucent" CONTACT-INFO "Please consult with Customer Service to ensure the most appropriate version of this document is used with the products in question: Alcatel-Lucent, Enterprise Solutions Division (Formerly Alcatel Internetworking, Incorporated) 26801 West Agoura Road Agoura Hills, CA 91301-5122 United States Of America Telephone: North America +1 800 995 2696 Latin America +1 877 919 9526 Europe +31 23 556 0100 Asia +65 394 7933 All Other +1 818 878 4507 Electronic Mail: support@ind.alcatel.com World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs" DESCRIPTION "This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This proprietary MIB contains management information for the configuration of PIM-SM and PIM-DM global configuration parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent Copyright (C) 2015 ALE USA, Inc. ALL RIGHTS RESERVED WORLDWIDE" REVISION "200704030000Z" DESCRIPTION "The latest version of this MIB Module." REVISION "201505280000Z" DESCRIPTION "Added V4/V6 bidir ssm compatibility, bidir fast-join, asm fast-join and ssm-fast-join." ::= { routingIND1Pim 1 } alcatelIND1PIMMIBObjects OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 1 } alaPimsmGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 1 } alaPimdmGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 2 } alaPimGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 3 } -- ************************************************************************ -- PIM-SM Global Configuration -- ************************************************************************ alaPimsmAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM-SM protocol on this router." DEFVAL { disable } ::= {alaPimsmGlobalConfig 1} alaPimsmMaxRPs OBJECT-TYPE SYNTAX Integer32 (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of C-RPs allowed in the PIM-SM domain." DEFVAL { 32 } ::= { alaPimsmGlobalConfig 2 } alaPimsmProbeTime OBJECT-TYPE SYNTAX Integer32 (1..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "When NULL Registers are used, this is the time between sending a NULL Register and the Register- Suppression-Timer expiring unless it is restarted by receiving a Register-Stop." DEFVAL { 5 } ::= { alaPimsmGlobalConfig 3} alaPimsmOldRegisterMessageSupport OBJECT-TYPE SYNTAX INTEGER { header(1), full(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the application of the checksum function on received Register messages in the PIM-SM domain. When set to full(2), the checksum for a register message is computed for the entire packet (i.e. includes data). When set to header(1), the checksum is done only on the first 8 bytes of the packet. This variable is provided for interoperability reasons and may be required for Compatibility with older implementations of PIM-SM v2. This parameter must be set the same throughout the PIM-SM domain." DEFVAL { header } ::= { alaPimsmGlobalConfig 4 } alaPimsmAdminSPTConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables SPT Switchover upon receiving the first data packet." DEFVAL { enable } ::= {alaPimsmGlobalConfig 5 } alaPimsmRPThreshold OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the RP threshold value (in bps) to be used in determining when to switch to native forwarding at the RP. The value of 0 disables the RP Threshold functionality." DEFVAL { 1 } ::= {alaPimsmGlobalConfig 6 } alaPimsmV6AdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM-SM IPv6 protocol on this router." DEFVAL { disable } ::= {alaPimsmGlobalConfig 7 } alaPimsmV6SPTConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables PIM IPv6 SPT Switchover upon receiving the first data packet." DEFVAL { enable } ::= {alaPimsmGlobalConfig 8 } alaPimsmV6RPSwitchover OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether PIM IPv6 will attempt to switch to native forwarding at the RP upon receiving the first register-encapsulated packet." DEFVAL { enable } ::= {alaPimsmGlobalConfig 9 } alaPimsmBidirStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM BIDIR protocol on this router." DEFVAL { disable } ::= {alaPimsmGlobalConfig 10} alaPimsmBidirPeriodicInterval OBJECT-TYPE SYNTAX Integer32 (0..2000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval at which the DF for each RPA will periodically announce its status in a Winner message. A value of 0 indicates that periodic messages will not be sent." DEFVAL { 60 } ::= { alaPimsmGlobalConfig 11 } alaPimsmBidirDFAbort OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether the DF election will be automatically aborted if a PIM hello is received from a PIM neighbor without the bidirectional capable option. By default, the DF election will still occur among those PIM routers that support BIDIR. By enabling this option, if a BIDIR- capable router receives a PIM hello from a non-BIDIR-capable router, the DF election is aborted." DEFVAL { disable } ::= {alaPimsmGlobalConfig 12} alaPimsmNonBidirHelloPeriod OBJECT-TYPE SYNTAX Unsigned32 (10..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum time that must elapse between alaPimNonBidirHello notifications originated by this router. The default value of 65535 represents an 'infinite' time, in which case, no alaPimNonBidirHello notifications are ever sent. The non-zero minimum allowed value provides resilience against propagation of denial-of-service attacks from the control plane to the network management plane." DEFVAL { 65535 } ::= { alaPimsmGlobalConfig 13 } alaPimsmNonBidirHelloMsgsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of PIM Hello messages that have been received by a BIDIR-capable device that do not have the Bidirectional Capable option. This counter is incremented if BIDIR mode is enabled on this router and a PIM Hello message is received from a PIM neighbor that does not include the Bidirectional Capable option. By default, the reception of these messages will not effect the BIDIR DF election. The alaPimsmBidirDFAbort object may be used to change the default behavior and have the DF election aborted whenever a BIDIR-capable router receives a PIM hello from a non-BIDIR-capable router." ::= { alaPimsmGlobalConfig 14 } alaPimsmNonBidirHelloAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The address type stored in alaPimsmNonBidirHelloOrigin. If no Non Bidir Hello messages have been received, this object is set to unknown(0)." ::= { alaPimsmGlobalConfig 15 } alaPimsmNonBidirHelloOrigin OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The source address of the last Non Bidir Hello message received by this device." ::= { alaPimsmGlobalConfig 16 } alaPimsmV6BidirStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM IPv6 BIDIR protocol on this router." DEFVAL { disable } ::= {alaPimsmGlobalConfig 17} alaPimsmRPHashStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables applying the PIM hash function defined in RFC 4601 when selecting an RP from two or more equal group-range-to-RP mappings." REFERENCE "RFC 4601 section 4.7.2" DEFVAL { disable } ::= {alaPimsmGlobalConfig 18 } alaPimsmBidirSsmCompat OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether PIM BIDIR will support receiving IGMPv3 source-specific joins and treat them as a (*,G) join. By default, IGMPv3 source-specific joins are ignored when PIM is operating in BIDIR mode." DEFVAL { disable } ::= {alaPimsmGlobalConfig 19} alaPimsmV6BidirSsmCompat OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether IPv6 PIM BIDIR will support receiving MLDv2 source-specific joins and treat them as a (*,G) join. By default, MLDv2 source-specific joins are ignored when PIM is operating in BIDIR mode." DEFVAL { disable } ::= {alaPimsmGlobalConfig 20} alaPimsmBidirFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether PIM BIDIR will automatically create the routes in hardware as soon as the BIDIR (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 21} alaPimsmV6BidirFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether IPv6 PIM BIDIR will automatically create the routes in hardware as soon as the BIDIR (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 22} alaPimsmAsmFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether PIM ASM will automatically create the (*,G) routes in hardware as soon as the ASM (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 23} alaPimsmV6AsmFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether IPv6 PIM ASM will automatically create the (*,G) routes in hardware as soon as the ASM (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 24} alaPimsmSsmFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether PIM will automatically create the (S,G) routes in hardware as soon as the (S,G) routes are learned. This includes PIM Sparse Mode (S,G) routes as well as PIM SSM (S,G) routes. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 25} alaPimsmV6SsmFastJoin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables whether IPv6 PIM will automatically create the (S,G) routes in hardware as soon as the (S,G) routes are learned. This includes PIM Sparse Mode (S,G) routes as well as PIM SSM (S,G) routes. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch." DEFVAL { disable } ::= {alaPimsmGlobalConfig 26} -- ************************************************************************ -- PIM-DM Global Configuration -- ************************************************************************ alaPimdmAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM-DM protocol on this router." DEFVAL { disable } ::= {alaPimdmGlobalConfig 1} alaPimdmStateRefreshTimeToLive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded." DEFVAL { 16 } ::= {alaPimdmGlobalConfig 2} alaPimdmStateRefreshLimitInterval OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "This router will not forward successive State Refresh messages received at less than this interval." DEFVAL { 0 } ::= {alaPimdmGlobalConfig 3} alaPimdmV6AdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables the PIM-DM IPv6 protocol on this router." DEFVAL { disable } ::= {alaPimdmGlobalConfig 4} -- -- The PIM Dense Group Table -- This table allows the configuration of pim group mappings to be -- used with dense mode. These mappings correspond to the sparse -- mappings defined in the pimStaticRPTable defined in the PIM-STD-MIB. -- alaPimdmDenseGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaPimdmDenseGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to manage configuration of dense groups. If the group prefixes configured for two or more rows in this table overlap, the row with the greatest value of alaPimdmDenseGroupGrpPrefixLength is used for the overlapping range." ::= { alaPimdmGlobalConfig 5 } alaPimdmDenseGroupEntry OBJECT-TYPE SYNTAX AlaPimdmDenseGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the alaPimdmDenseGroupTable. This entry is preserved on agent restart." INDEX { alaPimdmDenseGroupAddressType, alaPimdmDenseGroupGrpAddress, alaPimdmDenseGroupGrpPrefixLength } ::= { alaPimdmDenseGroupTable 1 } AlaPimdmDenseGroupEntry ::= SEQUENCE { alaPimdmDenseGroupAddressType InetAddressType, alaPimdmDenseGroupGrpAddress InetAddress, alaPimdmDenseGroupGrpPrefixLength InetAddressPrefixLength, alaPimdmDenseGroupOverrideDynamic TruthValue, alaPimdmDenseGroupPrecedence Unsigned32, alaPimdmDenseGroupRowStatus RowStatus } alaPimdmDenseGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of this entry." ::= { alaPimdmDenseGroupEntry 1 } alaPimdmDenseGroupGrpAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address that, when combined with alaPimdmDenseGroupGrpPrefixLength, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. This address object is only significant up to alaPimdmDenseGroupGrpPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." ::= { alaPimdmDenseGroupEntry 2 } alaPimdmDenseGroupGrpPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group prefix length that, when combined with alaPimdmDenseGroupGrpAddress, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. If alaPimdmDenseGroupAddressType is 'ipv4' or 'ipv4z', this object must be in the range 4..32. If alaPimdmDenseGroupGrpAddressType is 'ipv6' or 'ipv6z', this object must be in the range 8..128." ::= { alaPimdmDenseGroupEntry 3 } alaPimdmDenseGroupOverrideDynamic OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether this dense group configuration will override other group mappings in this group prefix. If this object is TRUE, then it will override: - RP information learned dynamically for groups in this group prefix. - RP information configured in alaPimdmDenseGroupTable with alaPimdmDenseGroupOverrideDynamic set to FALSE. See pimGroupMappingTable for details." DEFVAL { false } ::= { alaPimdmDenseGroupEntry 4 } alaPimdmDenseGroupPrecedence OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The value for pimGroupMappingPrecedence to be used for this static RP configuration. This allows fine control over which configuration is overridden by this static configuration. If alaPimdmDenseGroupOverrideDynamic is set to TRUE, all dynamic RP configuration is overridden by this static configuration, whatever the value of this object. The absolute values of this object have a significance only on the local router and do not need to be coordinated with other routers. A setting of this object may have different effects when applied to other routers. Do not use this object unless fine control of static RP behavior on the local router is required." ::= { alaPimdmDenseGroupEntry 5 } alaPimdmDenseGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which rows in this table can be created and destroyed. All writeable objects in this entry can be modified when the status of this entry is active(1)." ::= { alaPimdmDenseGroupEntry 6 } -- ************************************************************************ -- PIM Global Configuration -- ************************************************************************ alaPimBfdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables PIM with the BFD protocol on this router." DEFVAL { disable } ::= {alaPimGlobalConfig 1} alaPimBfdAllInterfaceStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables BFD for all PIM interfaces on this router." DEFVAL { disable } ::= {alaPimGlobalConfig 2} alaPimMoFRRStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables MoFRR (Multicast only Fast Re-Route) on this router." DEFVAL { disable } ::= {alaPimGlobalConfig 3} alaPimMoFRRAllRouteStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "By default, MoFRR is only applied to multicast routes that have local clients. Enabling alaPimMoFRRAllRouteStatus will enable MoFRR on all routes whether there are local clients or not. alaPimMoFRRStatus must be enabled for this to take effect." DEFVAL { disable } ::= {alaPimGlobalConfig 4} -- ************************************************************************ -- Expansion of pimInterfaceEntry -- ************************************************************************ alaPimInterfaceAugTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaPimInterfaceAugEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Expansion for pimInterfaceTable" ::= { alaPimGlobalConfig 5 } alaPimInterfaceAugEntry OBJECT-TYPE SYNTAX AlaPimInterfaceAugEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of alaPimInterfaceAugTable" AUGMENTS { pimInterfaceEntry } ::= { alaPimInterfaceAugTable 1 } AlaPimInterfaceAugEntry ::= SEQUENCE { alaPimInterfaceBfdStatus INTEGER } alaPimInterfaceBfdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disables BFD for particular interfaces of PIM." DEFVAL { disable } ::= { alaPimInterfaceAugEntry 1 } alaPimMbrAllSourcesStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables PIM to notify DVMRP about the routes to all multicast sources learned instead of just the directly connected subnets so that these routes can be advertised in the DVMRP domain via standard DVMRP mechanisms. This object is only applicable if the router is operating as a Multicast Border Router." DEFVAL { disable } ::= {alaPimGlobalConfig 6} alaPimMbrOperStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether MBR is currently enabled/disabled for PIM." ::= {alaPimGlobalConfig 7} alaPimV6BfdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables PIM IPv6 with the BFD protocol on this router." DEFVAL { disable } ::= {alaPimGlobalConfig 8} alaPimV6BfdAllInterfaceStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administratively enables/disables BFD for all PIM IPv6 interfaces on this router." DEFVAL { disable } ::= {alaPimGlobalConfig 9} -- ************************************************************************ -- PIM Notifications -- ************************************************************************ alaPimNotifications OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 0 } alaPimNonBidirHello NOTIFICATION-TYPE OBJECTS { alaPimsmNonBidirHelloAddressType, alaPimsmNonBidirHelloOrigin } STATUS current DESCRIPTION "An alaPimNonBidirHello notification signifies that a bidir-capable router has received a PIM hello from a non-bidir-capable router. This notification is generated whenever the counter alaPimsmNonBidirHelloMsgsRcvd is incremented, subject to the rate limit specified by alaPimsmNonBidirHelloNotificationPeriod." ::= { alaPimNotifications 1 } -- conformance information alcatelIND1PIMMIBConformance OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 2 } alcatelIND1PIMMIBCompliances OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBConformance 1 } alcatelIND1PIMMIBGroups OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBConformance 2 } -- compliance statements alaPimsmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for routers running PIM Sparse Mode and implementing the ALCATEL-IND1-PIM MIB." MODULE -- this module MANDATORY-GROUPS { alaPimsmConfigMIBGroup, alaPimConfigMIBGroup } ::= { alcatelIND1PIMMIBCompliances 1 } alaPimdmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for routers running PIM Dense Mode and implementing the ALCATEL-IND1-PIM MIB." MODULE -- this module MANDATORY-GROUPS { alaPimdmConfigMIBGroup, alaPimConfigMIBGroup } ::= { alcatelIND1PIMMIBCompliances 2 } -- units of conformance alaPimsmConfigMIBGroup OBJECT-GROUP OBJECTS { alaPimsmAdminStatus, alaPimsmMaxRPs, alaPimsmProbeTime, alaPimsmOldRegisterMessageSupport, alaPimsmAdminSPTConfig, alaPimsmRPThreshold, alaPimsmV6AdminStatus, alaPimsmV6SPTConfig, alaPimsmV6RPSwitchover, alaPimsmBidirStatus, alaPimsmBidirPeriodicInterval, alaPimsmBidirDFAbort, alaPimsmNonBidirHelloPeriod, alaPimsmNonBidirHelloMsgsRcvd, alaPimsmV6BidirStatus, alaPimsmRPHashStatus, alaPimsmBidirSsmCompat, alaPimsmV6BidirSsmCompat, alaPimsmBidirFastJoin, alaPimsmV6BidirFastJoin, alaPimsmAsmFastJoin, alaPimsmV6AsmFastJoin, alaPimsmSsmFastJoin, alaPimsmV6SsmFastJoin } STATUS current DESCRIPTION "A collection of objects to support management of global configuration parameters of PIM Sparse Mode routers." ::= { alcatelIND1PIMMIBGroups 1 } alaPimdmConfigMIBGroup OBJECT-GROUP OBJECTS { alaPimdmAdminStatus, alaPimdmStateRefreshTimeToLive, alaPimdmStateRefreshLimitInterval, alaPimdmV6AdminStatus, alaPimdmDenseGroupOverrideDynamic, alaPimdmDenseGroupPrecedence, alaPimdmDenseGroupRowStatus } STATUS current DESCRIPTION "A collection of objects to support management of global configuration parameters of PIM Dense Mode routers." ::= { alcatelIND1PIMMIBGroups 2 } alaPimConfigMIBGroup OBJECT-GROUP OBJECTS { alaPimBfdStatus, alaPimBfdAllInterfaceStatus, alaPimMoFRRStatus, alaPimMoFRRAllRouteStatus, alaPimInterfaceBfdStatus, alaPimMbrAllSourcesStatus, alaPimMbrOperStatus, alaPimV6BfdStatus, alaPimV6BfdAllInterfaceStatus } STATUS current DESCRIPTION "A collection of objects to support management of global configuration parameters of PIM routers." ::= { alcatelIND1PIMMIBGroups 3 } alaPimOptionalGroup OBJECT-GROUP OBJECTS { alaPimsmNonBidirHelloAddressType, alaPimsmNonBidirHelloOrigin } STATUS current DESCRIPTION " PIM objects to stop the tools from complaining " ::= { alcatelIND1PIMMIBGroups 4 } alaPimNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { alaPimNonBidirHello } STATUS current DESCRIPTION " PIM Notification objects " ::= { alcatelIND1PIMMIBGroups 5 } END