-- ZyXEL Communications Corporation -- Private Enterprise MIB definition -- $Log: zyxel-SAM1216.mib $ -- Revision 1.5 2010/03/17 10:24:51 cylien -- Revision 1.4 2010/03/11 02:14:52 cylien -- Revision 1.3 2009/10/09 02:10:10 cylien -- Revision 1.2 2009/07/28 09:00:42 lbr -- Revision 1.1 2008/07/11 09:36:01 maverick -- Initial revision -- Revision 1.3 2007/11/26 06:34:38 kenny -- Revision 1.2 2007/09/19 02:44:42 niceguy -- Revision 1.1 2006/08/28 05:32:54 kenny -- Initial revision -- Revision 1.5 2006/08/23 02:14:33 niceguy -- Revision 1.4 2006/08/04 07:48:05 niceguy -- Revision 1.3 2006/07/19 07:20:53 niceguy -- Revision 1.2 2006/07/07 02:38:09 niceguy -- Revision 1.1 2006/06/08 09:51:36 niceguy -- Initial revision -- Initial revision ZYXEL-SAM1216 DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI ifIndex, DisplayString, PhysAddress FROM RFC1213-MIB RowStatus FROM SNMPv2-TC dot1qVlanIndex, VlanIndex, PortList FROM Q-BRIDGE-MIB MacAddress, Timeout, BridgeId FROM BRIDGE-MIB; zyxel OBJECT IDENTIFIER ::= { enterprises 890 } products OBJECT IDENTIFIER ::= { zyxel 1 } accessSwitch OBJECT IDENTIFIER ::= { products 5 } sesSeries OBJECT IDENTIFIER ::= { accessSwitch 5 } sam1216-22 OBJECT IDENTIFIER ::= { sesSeries 6 } -- acl OBJECT IDENTIFIER ::= { sam1216-22 1 } alarmconf OBJECT IDENTIFIER ::= { sam1216-22 2 } -- config OBJECT IDENTIFIER ::= { sam1216-22 3 } -- diagnostic OBJECT IDENTIFIER ::= { sam1216-22 4 } -- ipconf OBJECT IDENTIFIER ::= { sam1216-22 5 } -- lcm OBJECT IDENTIFIER ::= { sam1216-22 6 } multicast OBJECT IDENTIFIER ::= { sam1216-22 7 } port OBJECT IDENTIFIER ::= { sam1216-22 8 } -- profile OBJECT IDENTIFIER ::= { sam1216-22 9 } switch OBJECT IDENTIFIER ::= { sam1216-22 10 } sys OBJECT IDENTIFIER ::= { sam1216-22 11 } trap OBJECT IDENTIFIER ::= { sam1216-22 12 } statistics OBJECT IDENTIFIER ::= { sam1216-22 13 } clear OBJECT IDENTIFIER ::= { sam1216-22 14 } ---------------------------------------- -- acl ---------------------------------------- -- Standalone IP DSLAM puts all ACL features in 'switch', from OID 51 dhcp OBJECT IDENTIFIER ::= { switch 51 } -- dot1x OBJECT IDENTIFIER ::= { switch 52 } macfilter OBJECT IDENTIFIER ::= { switch 53 } -- pktfilter OBJECT IDENTIFIER ::= { switch 54 } dhcpSnoop OBJECT IDENTIFIER ::= { switch 55 } acl OBJECT IDENTIFIER ::= { switch 56 } pppoeAgent OBJECT IDENTIFIER ::= { switch 57 } -------------------- -- DHCP Relay -------------------- dhcpRelayEnable OBJECT-TYPE SYNTAX INTEGER { auto(1), both(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP relay Option82 function." ::= { dhcp 1 } dhcpRelay82Table OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelay82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains DHCP Relay configuration." ::= { dhcp 2 } dhcpRelay82Entry OBJECT-TYPE SYNTAX DhcpRelay82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of DHCP Relay table." INDEX { dot1qVlanIndex } ::= { dhcpRelay82Table 1 } DhcpRelay82Entry ::= SEQUENCE { dhcpRelay82PrimaryServer IpAddress, dhcpRelay82SecondaryServer IpAddress, dhcpRelay82ActiveServer INTEGER, dhcpRelay82Enable INTEGER, dhcpRelay82Info DisplayString, dhcpRelay82RelayMode INTEGER, dhcpRelay82Suboption2Enable INTEGER, dhcpRelay82Suboption2Info DisplayString, dhcpRelay82EntryEnable INTEGER, dhcpRelay82EntryOptionMode INTEGER } dhcpRelay82PrimaryServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay primary server." ::= { dhcpRelay82Entry 1 } dhcpRelay82SecondaryServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay secondary server." ::= { dhcpRelay82Entry 2 } dhcpRelay82ActiveServer OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current active DHCP Relay server." ::= { dhcpRelay82Entry 3 } dhcpRelay82Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP relay and Option82 function." ::= { dhcpRelay82Entry 4 } dhcpRelay82Info OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-create STATUS current DESCRIPTION "User specific Option82 information." ::= { dhcpRelay82Entry 5 } dhcpRelay82RelayMode OBJECT-TYPE SYNTAX INTEGER { auto(1), both(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP relay mode." ::= { dhcpRelay82Entry 6 } dhcpRelay82Suboption2Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Option 82 sub-option 2." ::= { dhcpRelay82Entry 8 } dhcpRelay82Suboption2Info OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "User specified information for Option 82 sub-option 2." ::= { dhcpRelay82Entry 9 } dhcpRelay82EntryEnable OBJECT-TYPE SYNTAX INTEGER { auto(1), both(2), disable(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP Relay" ::= { dhcpRelay82Entry 10 } dhcpRelay82EntryOptionMode OBJECT-TYPE SYNTAX INTEGER { private(1), tr101(2), tr101WithVlan(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Option82 format." ::= { dhcpRelay82Entry 11 } dhcpRelayOption82Sub1Info OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-write STATUS current DESCRIPTION "User specific Option82 subOption1 (Agent circuit ID) information." ::= { dhcp 3 } maxNumOfDhcpRelay82Conf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows that can be created in dhcpRelay82Table." ::= { dhcp 4 } dhcpRelayOption82Sub1Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP relay Option82 subOption1 (Agent Circuit ID) function." ::= { dhcp 5 } dhcpRelayOption82Sub2Info OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-write STATUS current DESCRIPTION "User specific Option82 subOption2 (Agent Remote ID) information." ::= { dhcp 6 } dhcpRelayOption82Sub2Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP relay Option82 subOption2 (Agent Remote ID) function." ::= { dhcp 7 } -------------------- -- MAC Filter -------------------- -- MAC Filter Port Table macFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the status of mac filtering for each port." ::= { macfilter 1 } macFilterPortEntry OBJECT-TYPE SYNTAX MacFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in macFilterPortTable." INDEX { ifIndex } ::= { macFilterPortTable 1 } MacFilterPortEntry ::= SEQUENCE { macFilterPortEnable INTEGER, macFilterPortMacCount INTEGER, macFilterPortFilterMode INTEGER } macFilterPortEnable OBJECT-TYPE SYNTAX INTEGER { enableMacFilter(1), enableMacCount(2), -- enableOuiFilter(3), disable(4), enableMacFilterAndMacCount(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable MAC filtering for the port." ::= { macFilterPortEntry 1 } macFilterPortMacCount OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The total number of MAC addresses allowed for the port." ::= { macFilterPortEntry 2 } macFilterPortFilterMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The mac filter mode (accept or deny) for the port." ::= { macFilterPortEntry 3 } maxNumOfMacFiltersInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of mac filters supported in the system." ::= { macfilter 2 } maxNumOfMacFiltersPerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of mac filters supported per port." ::= { macfilter 3 } currNumOfMacFiltersInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of mac filters in the system." ::= { macfilter 4 } -- MAC Table macFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the mac filter addresses." ::= { macfilter 5 } macFilterEntry OBJECT-TYPE SYNTAX MacFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of macFilterTable." INDEX { ifIndex, macFilterAddr } ::= { macFilterTable 1 } MacFilterEntry ::= SEQUENCE { macFilterAddr PhysAddress, macFilterRowStatus RowStatus } macFilterAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The mac address which can pass through or be rejected from the port." ::= { macFilterEntry 1 } macFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { macFilterEntry 2 } -- Batch Set for MAC Filter macfilterBatchSet OBJECT IDENTIFIER ::= { macfilter 6 } macfilterTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { macfilterBatchSet 1 } macfilterOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter." ::= { macfilterBatchSet 2 } macFilterMacCountForBatchSet OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The total number of MAC addresses allowed for a port." ::= { macfilterBatchSet 3 } -- OUI Filter Table ouiFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the OUI filter addresses." ::= { macfilter 7 } ouiFilterEntry OBJECT-TYPE SYNTAX OuiFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of ouiFilterTable." INDEX { ifIndex, ouiFilterAddr } ::= { ouiFilterTable 1 } OuiFilterEntry ::= SEQUENCE { ouiFilterAddr OCTET STRING, ouiFilterRowStatus RowStatus } ouiFilterAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The first three bytes of the mac address which can pass through or be rejected from the port." ::= { ouiFilterEntry 1 } ouiFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { ouiFilterEntry 2 } maxNumOfOuiFiltersPerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of OUI filters supported per port." ::= { macfilter 8 } ouiFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the status of oui filtering for each port." ::= { macfilter 9 } ouiFilterPortEntry OBJECT-TYPE SYNTAX OuiFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in macFilterPortTable." INDEX { ifIndex } ::= { ouiFilterPortTable 1 } OuiFilterPortEntry ::= SEQUENCE { ouiFilterPortEnable INTEGER, ouiFilterPortFilterMode INTEGER } ouiFilterPortEnable OBJECT-TYPE SYNTAX INTEGER { enableOuiFilter(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable oui filtering for the port." ::= { ouiFilterPortEntry 1 } ouiFilterPortFilterMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The oui filter mode (accept or deny) for the port." ::= { ouiFilterPortEntry 2 } -------------------- -- DHCP Snoop -------------------- -- dhcpSnoopPortTable dhcpSnoopPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes DHCP snooping enable/disable for each port." ::= { dhcpSnoop 1 } dhcpSnoopPortEntry OBJECT-TYPE SYNTAX DhcpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopPortTable." INDEX { ifIndex } ::= { dhcpSnoopPortTable 1 } DhcpSnoopPortEntry ::= SEQUENCE { dhcpSnoopEnable INTEGER } dhcpSnoopEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP snooping for a port." ::= { dhcpSnoopPortEntry 1 } -- dhcpSnoopOperation dhcpSnoopTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { dhcpSnoop 2 } dhcpSnoopOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush." ::= { dhcpSnoop 3 } -- dhcpStaticTable dhcpStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines DHCP static IP addresses." ::= { dhcpSnoop 4 } dhcpStaticEntry OBJECT-TYPE SYNTAX DhcpStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpStaticTable." INDEX { ifIndex, dhcpStaticIpAddr } ::= { dhcpStaticTable 1 } DhcpStaticEntry ::= SEQUENCE { dhcpStaticIpAddr IpAddress, dhcpStaticRowStatus RowStatus } dhcpStaticIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address which can pass through the port." ::= { dhcpStaticEntry 1 } dhcpStaticRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table entry." ::= { dhcpStaticEntry 2 } maxNumOfDhcpStaticIp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of DHCP static IP addresses which can be created for a port." ::= { dhcpSnoop 5 } dhcpSnoopLan2lanEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP snoop lan2lan function." ::= { dhcpSnoop 6 } -- acl --aclSetTable aclSetTable OBJECT-TYPE SYNTAX SEQUENCE OF AclSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "aclsetTable." ::= { acl 1 } aclSetEntry OBJECT-TYPE SYNTAX AclSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of aclSetTable." INDEX { ifIndex, aclSetVpi, aclSetVci, aclSetProfileName } ::= { aclSetTable 1 } AclSetEntry ::= SEQUENCE { aclSetVpi INTEGER, aclSetVci INTEGER, aclSetProfileName DisplayString, aclSetRowStatus RowStatus } aclSetVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPI value" ::= { aclSetEntry 1 } aclSetVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VCI value" ::= { aclSetEntry 2 } aclSetProfileName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile name" ::= { aclSetEntry 3 } aclSetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus of aclSetEntry" ::= { aclSetEntry 4 } --aclProfileTable aclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "aclProfileTable." ::= { acl 2 } aclProfileEntry OBJECT-TYPE SYNTAX AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of aclProfileTable." INDEX { aclProfileRuleName } ::= { aclProfileTable 1 } AclProfileEntry ::= SEQUENCE { aclProfileRuleName DisplayString, aclProfileRuleNumber INTEGER, aclProfileActionNumber INTEGER, aclProfileRuleParamMask INTEGER, aclProfileRuleEtype INTEGER, aclProfileRuleVid INTEGER, aclProfileRuleSmac PhysAddress, aclProfileRuleDmac PhysAddress, aclProfileRulePriority INTEGER, aclProfileRuleProtocol INTEGER, aclProfileRuleSrcIP IpAddress, aclProfileRuleSrcIPMask INTEGER, aclProfileRuleDestIP IpAddress, aclProfileRuleDestIPMask INTEGER, aclProfileRuleStartTos INTEGER, aclProfileRuleEndTos INTEGER, aclProfileRuleSrcStartPort INTEGER, aclProfileRuleSrcEndPort INTEGER, aclProfileRuleDestStartPort INTEGER, aclProfileRuleDestEndPort INTEGER, aclProfileActionRate INTEGER, aclProfileActionrvlan INTEGER, aclProfileActionrpri INTEGER, aclProfileRowStatus RowStatus } aclProfileRuleName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Profile rule name" ::= { aclProfileEntry 1 } aclProfileRuleNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{|dstip /{|tos {|srcport {|dstport }}}}} (14) " ::= { aclProfileEntry 2 } aclProfileActionNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection." ::= { aclProfileEntry 3 } aclProfileRuleParamMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport " ::= { aclProfileEntry 4 } aclProfileRuleEtype OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule etype " ::= { aclProfileEntry 5 } aclProfileRuleVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule vid" ::= { aclProfileEntry 6 } aclProfileRuleSmac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source MAC" ::= { aclProfileEntry 7 } aclProfileRuleDmac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination MAC" ::= { aclProfileEntry 8 } aclProfileRulePriority OBJECT-TYPE SYNTAX INTEGER (1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule priority" ::= { aclProfileEntry 9 } aclProfileRuleProtocol OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype" ::= { aclProfileEntry 10 } aclProfileRuleSrcIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source IP" ::= { aclProfileEntry 11 } aclProfileRuleSrcIPMask OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of source IP mask" ::= { aclProfileEntry 12 } aclProfileRuleDestIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source IP" ::= { aclProfileEntry 13 } aclProfileRuleDestIPMask OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of dest IP mask" ::= { aclProfileEntry 14 } aclProfileRuleStartTos OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule start type of service" ::= { aclProfileEntry 15 } aclProfileRuleEndTos OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule end type of service" ::= { aclProfileEntry 16 } aclProfileRuleSrcStartPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source start port" ::= { aclProfileEntry 17 } aclProfileRuleSrcEndPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source end port" ::= { aclProfileEntry 18 } aclProfileRuleDestStartPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination start port" ::= { aclProfileEntry 19 } aclProfileRuleDestEndPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination end port" ::= { aclProfileEntry 20 } aclProfileActionRate OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this rate" ::= { aclProfileEntry 21 } aclProfileActionrvlan OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this vlan" ::= { aclProfileEntry 22 } aclProfileActionrpri OBJECT-TYPE SYNTAX INTEGER (1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this priority" ::= { aclProfileEntry 23 } aclProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status of the entry." ::= { aclProfileEntry 24 } -------------------- -- PPPoE Agent -------------------- -- pppoeAgentTable pppoeAgentTable OBJECT-TYPE SYNTAX SEQUENCE OF PppoeAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains PPPoE DHCP Relay configuration." ::= { pppoeAgent 1 } pppoeAgentEntry OBJECT-TYPE SYNTAX PppoeAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of pppoeAgentTable." INDEX { dot1qVlanIndex } ::= { pppoeAgentTable 1 } PppoeAgentEntry ::= SEQUENCE { pppoeAgentEnable INTEGER, pppoeAgentInfo DisplayString, pppoeAgentRowStatus RowStatus, pppoeAgentOptionMode INTEGER } pppoeAgentEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP relay and Option82 function." ::= { pppoeAgentEntry 1 } pppoeAgentInfo OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-create STATUS current DESCRIPTION "User specific Option82 information." ::= { pppoeAgentEntry 2 } pppoeAgentRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table entry." ::= { pppoeAgentEntry 3 } pppoeAgentOptionMode OBJECT-TYPE SYNTAX INTEGER { private(1), tr101(2), tr101WithVlan(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Option82 format." ::= { pppoeAgentEntry 4 } maxNumOfPppoeAgentConf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows that can be created in pppoeAgentTable." ::= { pppoeAgent 2 } ---------------------------------------- -- alarmconf ---------------------------------------- alarmOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff" ::= { alarmconf 1 } -- Alarm Conf Table alarmConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes alarm configuration." ::= { alarmconf 2 } alarmConfEntry OBJECT-TYPE SYNTAX AlarmConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmConfTable." INDEX { alarmConfId } ::= { alarmConfTable 1 } AlarmConfEntry ::= SEQUENCE { alarmConfId INTEGER, alarmConfFacility INTEGER, alarmConfTarget INTEGER, alarmConfSeverity INTEGER, alarmConfClearable INTEGER } alarmConfId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "5000: linkUp 5001: linkDown 5002: shdslLoopAttenCrossing 5003: shdslSNRMarginCrossing 5004: shdslPerfESThresh 5005: shdslPerfSESThresh 5006: shdslPerfCRCAnomaliesThresh 5007: shdslPerfLOSWSThresh 5008: shdslPerfUASThresh 10000: eqptVoltageError 10001: eqptTempError 10002: eqptHwRTCError 10003: eqptHWMonitorFailed 10004: coldStart 10005: warmStart 15000: sysReboot 15001: sysAlarmCutoffEnabled 15002: sysAlarmClearEnabled 15003: sysLoginFailed 15004: sysMacAntiSpoofing 20000: enetlinkUp 20001: enetlinkDown" ::= { alarmConfEntry 1 } alarmConfFacility OBJECT-TYPE SYNTAX INTEGER { local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm facility." ::= { alarmConfEntry 2 } alarmConfTarget OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog" ::= { alarmConfEntry 3 } alarmConfSeverity OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm severity" ::= { alarmConfEntry 4 } alarmConfClearable OBJECT-TYPE SYNTAX INTEGER { clearable(1), unclearable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear." ::= { alarmConfEntry 5 } -- Alarm Current Table alarmCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes current alarm information." ::= { alarmconf 3 } alarmCurrEntry OBJECT-TYPE SYNTAX AlarmCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmCurrTable." INDEX { alarmCurrIndex } ::= { alarmCurrTable 1 } AlarmCurrEntry ::= SEQUENCE { alarmCurrIndex INTEGER, alarmCurrOccurTime TimeTicks, alarmCurrTrapOid OBJECT IDENTIFIER, alarmCurrParam1 INTEGER, alarmCurrParam2 INTEGER, alarmCurrParam3 INTEGER, alarmCurrParam4 INTEGER, alarmCurrParam5 INTEGER, alarmCurrParam6 INTEGER, alarmCurrParam7 INTEGER, alarmCurrParam8 INTEGER, alarmCurrTimeDescr DisplayString, alarmCurrSeverity INTEGER, alarmCurrDescr DisplayString } alarmCurrIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Index of the alarm." ::= { alarmCurrEntry 1 } alarmCurrOccurTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm occurence time (in hundredths of a second) since the system was last re-initialized." ::= { alarmCurrEntry 2 } alarmCurrTrapOid OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "Trap OID of the alarm." ::= { alarmCurrEntry 3 } alarmCurrParam1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 1st parameter of the alarm." ::= { alarmCurrEntry 4 } alarmCurrParam2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 2nd parameter of the alarm." ::= { alarmCurrEntry 5 } alarmCurrParam3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 3rd parameter of the alarm." ::= { alarmCurrEntry 6 } alarmCurrParam4 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 4th parameter of the alarm." ::= { alarmCurrEntry 7 } alarmCurrParam5 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 5th parameter of the alarm." ::= { alarmCurrEntry 8 } alarmCurrParam6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 6th parameter of the alarm." ::= { alarmCurrEntry 9 } alarmCurrParam7 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 7th parameter of the alarm." ::= { alarmCurrEntry 10 } alarmCurrParam8 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 8th parameter of the alarm." ::= { alarmCurrEntry 11 } alarmCurrTimeDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The string representation of occurence time (YYYY/MM/DD HH:MM:SS)." ::= { alarmCurrEntry 12 } alarmCurrSeverity OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of the alarm." ::= { alarmCurrEntry 13 } alarmCurrDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The description of the alarm." ::= { alarmCurrEntry 14 } -- Alarm Severity Port Table alarmSeverityPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmSeverityPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the configuration of alarm reporting severity threshold for each port." ::= { alarmconf 4 } alarmSeverityPortEntry OBJECT-TYPE SYNTAX AlarmSeverityPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmSeverityPortTable." INDEX { ifIndex } ::= { alarmSeverityPortTable 1 } AlarmSeverityPortEntry ::= SEQUENCE { severityThresh INTEGER } severityThresh OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum alarm severity that is reported." ::= { alarmSeverityPortEntry 1 } ---------------------------------------- -- diagnostic ---------------------------------------- -- loopback OBJECT IDENTIFIER ::= { diagnostic 1 } -- ldm OBJECT IDENTIFIER ::= { diagnostic 2 } -- selt OBJECT IDENTIFIER ::= { diagnostic 3 } -- -------------------- -- selt -------------------- -- seltTarget OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "IfIndex of the port which would be performed single end loopback test." -- ::= { selt 1 } -- -- seltOps OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The manager sets the object to 1 to start the selt -- and the agent clears the object to zero when selt is successfully completed." -- ::= { selt 2 } -- -- seltStatus OBJECT-TYPE -- SYNTAX DisplayString -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Status description of the selt result." -- ::= { selt 3 } -- -- seltCableType OBJECT-TYPE -- SYNTAX INTEGER { -- awg24(1), -- awg26(2) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The cable type that selt result indicates." -- ::= { selt 4 } -- -- seltLoopEstimateLengthFt OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "feet" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The estimated loop length that selt result indicates." -- ::= { selt 5 } -- -- seltLoopEstimateLengthMeter OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "meter" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The estimated loop length that selt result indicates." -- ::= { selt 6 } ---------------------------------------- -- multicast ---------------------------------------- -- staticMulticast OBJECT IDENTIFIER ::= { multicast 2 } -- igmpFilter OBJECT IDENTIFIER ::= { multicast 3 } mcastBandwidth OBJECT IDENTIFIER ::= { multicast 4 } igmpCount OBJECT IDENTIFIER ::= { multicast 5 } mvlan OBJECT IDENTIFIER ::= { multicast 6 } queryVid OBJECT IDENTIFIER ::= { multicast 7 } igmpEnable OBJECT-TYPE SYNTAX INTEGER { enableProxy(1), enableSnooping(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP protocol." ::= { multicast 1 } -- igmpMode OBJECT-TYPE -- SYNTAX INTEGER { -- aggresive(1), -- normal(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "setting IGMP with aggresive mode will issue an IGMP report from new active port -- when topology change occurs, while normal mode won't." -- ::= { multicast 8 } -------------------- -- bandwidth -------------------- mcastDefaultBandwidth OBJECT-TYPE SYNTAX INTEGER (1..100000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Default bandwidth requirement for a multicast channel." ::= { mcastBandwidth 1 } maxNumOfMcastBw OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in mcastBwTable." ::= { mcastBandwidth 2 } -- mcastBwTable mcastBwTable OBJECT-TYPE SYNTAX SEQUENCE OF McastBwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines bandwidth budget for a range of multicast IP channels." ::= { mcastBandwidth 3 } mcastBwEntry OBJECT-TYPE SYNTAX McastBwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mcastBwTable." INDEX { mcastBwIndex, mcastBwStartIp, mcastBwEndIp } ::= { mcastBwTable 1 } McastBwEntry ::= SEQUENCE { mcastBwIndex INTEGER, mcastBwStartIp IpAddress, mcastBwEndIp IpAddress, mcastBwBandwidth INTEGER, mcastBwRowStatus RowStatus } mcastBwIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index which specify the entry." ::= { mcastBwEntry 1 } mcastBwStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The start multicast IP of the bandwidth control range." ::= { mcastBwEntry 2 } mcastBwEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The end multicast IP of the bandwidth control range." ::= { mcastBwEntry 3 } mcastBwBandwidth OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "The bandwidth budget for the multicast IP channels." ::= { mcastBwEntry 4 } mcastBwRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { mcastBwEntry 5 } -- mcastBwPortTable mcastBwPortTable OBJECT-TYPE SYNTAX SEQUENCE OF McastBwPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specify the multicast bandwidth control of the port." ::= { mcastBandwidth 4 } mcastBwPortEntry OBJECT-TYPE SYNTAX McastBwPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mcastBwPortTable." INDEX { ifIndex } ::= { mcastBwPortTable 1 } McastBwPortEntry ::= SEQUENCE { mcastBwPortEnable INTEGER, mcastBwPortBandwidth INTEGER } mcastBwPortEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable multicast bandwidth control for a port." ::= { mcastBwPortEntry 1 } mcastBwPortBandwidth OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Set bandwidth threshold for a port." ::= { mcastBwPortEntry 2 } -------------------- -- igmpCount -------------------- igmpCountPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpCountPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specify the IGMP count limiting of the port." ::= { igmpCount 1 } igmpCountPortEntry OBJECT-TYPE SYNTAX IgmpCountPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpCountPortTable." INDEX { ifIndex } ::= { igmpCountPortTable 1 } IgmpCountPortEntry ::= SEQUENCE { igmpCountPortEnable INTEGER, igmpCountPortLimit INTEGER } igmpCountPortEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP count limiting for a port." ::= { igmpCountPortEntry 1 } igmpCountPortLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed IGMP report count for a port." ::= { igmpCountPortEntry 2 } -------------------- -- mvlan -------------------- maxNumOfMvlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in mvlanTable." ::= { mvlan 1 } -- mvlanTable mvlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each multicast VLAN configured into the device." ::= { mvlan 2 } mvlanEntry OBJECT-TYPE SYNTAX MvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mvlanTable." INDEX { mvlanIndex } ::= { mvlanTable 1 } MvlanEntry ::= SEQUENCE { mvlanIndex VlanIndex, mvlanName DisplayString, mvlanEgressPorts PortList, mvlanUntaggedPorts PortList, mvlanRowStatus RowStatus } mvlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-ID refering to this VLAN." ::= { mvlanEntry 1 } mvlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." ::= { mvlanEntry 2 } mvlanEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently assigned to the egress list for this multicast VLAN." ::= { mvlanEntry 3 } mvlanUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which should transmit egress packets for this multicast VLAN as untagged." ::= { mvlanEntry 4 } mvlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { mvlanEntry 5 } -- mvlanTranslateTable mvlanTranslateTable OBJECT-TYPE SYNTAX SEQUENCE OF MvlanTranslateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains multicast to VLAN translation." ::= { mvlan 3 } mvlanTranslateEntry OBJECT-TYPE SYNTAX MvlanTranslateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mvlanTranslateTable." INDEX { dot1qVlanIndex, mvlanTranslateIndex } ::= { mvlanTranslateTable 1 } MvlanTranslateEntry ::= SEQUENCE { mvlanTranslateIndex INTEGER, mvlanTranslateStartIp IpAddress, mvlanTranslateEndIp IpAddress } mvlanTranslateIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index which specif the entry." ::= { mvlanTranslateEntry 1 } mvlanTranslateStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The start IP of the multicast VLAN translation." ::= { mvlanTranslateEntry 2 } mvlanTranslateEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The end IP of the multicast VLAN translation." ::= { mvlanTranslateEntry 3 } -------------------- -- queryVid -------------------- maxNumOfQryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in qryVidConfTable. This object is supported by R1.02 and later versions." ::= { queryVid 1 } -- qryVidConfTable qryVidConfTable OBJECT-TYPE SYNTAX SEQUENCE OF QryVidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines statically set VLANs used for response IGMP report. This table is supported by R1.02 and later versions." ::= { queryVid 2 } qryVidConfEntry OBJECT-TYPE SYNTAX QryVidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in qryVidConfTable." INDEX { qryVid } ::= { qryVidConfTable 1 } QryVidConfEntry ::= SEQUENCE { qryVid INTEGER, qryVidRowStatus RowStatus } qryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID." ::= { qryVidConfEntry 1 } qryVidRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { qryVidConfEntry 2 } -- qryVidStatusTable qryVidStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF QryVidStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows statically set or dynamically learned VLANs used for response IGMP report." ::= { queryVid 3 } qryVidStatusEntry OBJECT-TYPE SYNTAX QryVidStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in qryVidStatusTable." INDEX { qryVid } ::= { qryVidStatusTable 1 } QryVidStatusEntry ::= SEQUENCE { qryVidType INTEGER } qryVidType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN type." ::= { qryVidStatusEntry 1 } igmpVersion OBJECT-TYPE SYNTAX INTEGER { v2(1), v3(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting IGMP version." ::= { multicast 7 } ---------------------------------------- -- port ---------------------------------------- -- subrPortTable ::= { port 1 } -- adslPort OBJECT IDENTIFIER ::= { port 2 } shdslPort OBJECT IDENTIFIER ::= { port 3 } pvc OBJECT IDENTIFIER ::= { port 4 } ppvc OBJECT IDENTIFIER ::= { port 5 } portOperation OBJECT IDENTIFIER ::= { port 6 } -- pvcStats OBJECT IDENTIFIER ::= { port 7 } rpvc OBJECT IDENTIFIER ::= { port 8 } -- dsBcastDisableTable ::= { port 9 } paepvc OBJECT IDENTIFIER ::= { port 10 } tlspvc OBJECT IDENTIFIER ::= { port 11 } -- G.bond start from 51 gbond OBJECT IDENTIFIER ::= { port 51 } -- Subscriber Port Table subrPortTable OBJECT-TYPE SYNTAX SEQUENCE OF SubrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes subscriber attributes for the port." ::= { port 1 } subrPortEntry OBJECT-TYPE SYNTAX SubrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in subrPortTable." INDEX { ifIndex } ::= { subrPortTable 1 } SubrPortEntry ::= SEQUENCE { subrPortName DisplayString, subrPortTel DisplayString } subrPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the subscriber." ::= { subrPortEntry 1 } subrPortTel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Telephone number of the subscriber." ::= { subrPortEntry 2 } -------------------- -- adslPort -------------------- -- ADSL Line Table -- adslLineConfTable OBJECT-TYPE -- SYNTAX SEQUENCE OF AdslLineConfEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table includes common attributes describing the ADSL line." -- ::= { adslPort 1 } -- --adslLineConfEntry OBJECT-TYPE -- SYNTAX AdslLineConfEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in adslLineConfTable." -- INDEX { ifIndex } -- ::= { adslLineConfTable 1 } -- -- AdslLineConfEntry ::= -- SEQUENCE { -- adslLineConfAdslMode INTEGER, -- adslLineConfAnnexL INTEGER, -- adslLineConfAnnexM INTEGER, -- adslLineConfAnnexI INTEGER, -- adslLineConfOptionMask INTEGER, -- adslLineConfPowerMgmt INTEGER, -- adslLineConfPowerMode INTEGER, -- adslLineConfAturMaxTxPower INTEGER, -- adslLineConfAtucMaxTxPower INTEGER, -- adslLineConfMaxRxPower INTEGER, -- adslLineConfAturCarrierMask OCTET STRING, -- adslLineConfAtucCarrierMask0 OCTET STRING, -- adslLineConfAtucCarrierMask1 OCTET STRING, -- adslLineConfAturInp INTEGER, -- adslLineConfAtucInp INTEGER, -- adslLineConfL0Time INTEGER, -- adslLineConfL2Time INTEGER, -- adslLineConfL2ATPR INTEGER, -- adslLineConfL2ATPRT INTEGER, -- adslLineConfMaxL2Rate INTEGER, -- adslLineConfMinL2Rate INTEGER, -- adslLineConfL0toL2Rate INTEGER -- } -- -- adslLineConfAdslMode OBJECT-TYPE -- SYNTAX INTEGER { -- gDotLite(1), -- gDotDmt(2), -- t1Dot413(3), -- auto(4), -- etsi(5), -- adsl2(6), -- adsl2Plus(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "G.lite and T1.413 are only applicable to annex A board. -- ETSI is only applicable to annex B board." -- ::= { adslLineConfEntry 1 } -- -- adslLineConfAnnexL OBJECT-TYPE -- SYNTAX INTEGER { -- enableNarrowMode(1), -- enableWideMode(2), -- disable(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable annex L for the port(Only in AnnexA)." -- ::= { adslLineConfEntry 2 } -- -- adslLineConfAnnexM OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable annex M for the port(For BCM AnnexA solution)." -- ::= { adslLineConfEntry 3 } -- -- adslLineConfAnnexI OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable annex I for the port(For BCM AnnexA solution)." -- ::= { adslLineConfEntry 4 } -- -- adslLineConfOptionMask OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The semantic for each bit is: -- BIT 1 : Disable Trellis -- BIT 2 : Disable Reed-Solomon -- BIT 3 : Disable upstream bitswap -- BIT 4 : Disable downstream bitswap -- BIT 5 : Disable 1-bit constellation -- BIT 6 : Disable transmit windowing -- BIT 7 : Disable s=0.5 support (ADSL1 only) -- BIT 8 : Disable G.lite rate limit (ADSL1 only)" -- ::= { adslLineConfEntry 5 } -- -- adslLineConfPowerMgmt OBJECT-TYPE -- SYNTAX INTEGER { -- enableL2(1), -- enableL2andL3(2), -- disable(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable power management for the port." -- ::= { adslLineConfEntry 6 } -- -- adslLineConfPowerMode OBJECT-TYPE -- SYNTAX INTEGER { -- fix(1), -- priorityToPower(2), -- priorityToRate(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The power mode of the ADSL line." -- ::= { adslLineConfEntry 7 } -- -- adslLineConfAturMaxTxPower OBJECT-TYPE -- SYNTAX INTEGER (-130..200) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum allowed transmit power of ATU-R." -- ::= { adslLineConfEntry 8 } -- -- adslLineConfAtucMaxTxPower OBJECT-TYPE -- SYNTAX INTEGER (-50..200) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum allowed transmit power of ATU-C." -- ::= { adslLineConfEntry 9 } -- -- adslLineConfMaxRxPower OBJECT-TYPE -- SYNTAX INTEGER (-255..255) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum aggregate received power." -- ::= { adslLineConfEntry 10 } -- -- adslLineConfAturCarrierMask OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; -- CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. -- Bit set to 1 indicates the bin is masked off." -- ::= { adslLineConfEntry 11 } -- -- adslLineConfAtucCarrierMask0 OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; -- CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. -- Bit set to 1 indicates the bin is masked off." -- ::= { adslLineConfEntry 12 } -- -- adslLineConfAtucCarrierMask1 OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates -- the bin is masked off." -- ::= { adslLineConfEntry 13 } -- -- adslLineConfAturInp OBJECT-TYPE -- SYNTAX INTEGER { -- zero(1), -- zero-point-five(2), -- one(3), -- two(4), -- four(5), -- eight(6), -- sixteen(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. -- For CTLM solution, user can set value from 1 ~ 4, -- but for BCM solution, user can set value from 1 ~ 7." -- ::= { adslLineConfEntry 14 } -- -- adslLineConfAtucInp OBJECT-TYPE -- SYNTAX INTEGER { -- zero(1), -- zero-point-five(2), -- one(3), -- two(4), -- four(5), -- eight(6), -- sixteen(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. -- For CTLM solution, user can set value from 1 ~ 4, -- but for BCM solution, user can set value from 1 ~ 7." -- ::= { adslLineConfEntry 15 } -- -- -- adslLineConfL0Time OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set the minimum time in seconds that the ADSL line -- must stay in L0 power mode before changing to the L2 power mode. -- For CTLM solution, the range is 120 ~ 65535; -- for BCM solution, the range is 10 ~ 65535." -- ::= { adslLineConfEntry 16 } -- -- adslLineConfL2Time OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set minimum time in seconds that the ADSL line must stay in the -- L2 power mode before reducing the power again in the L2 power mode. -- For CTLM solution, the range is 60 ~ 65535; -- for BCM solution, the range is 10 ~ 65535." -- ::= { adslLineConfEntry 17 } -- -- adslLineConfL2ATPR OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set the maximum Aggregate Transmit Power Reduction (ATPR) -- in decibels (dB) that is permitted in a L2 power reduction. -- The system can gradually decrease the ADSL line transmission power -- while it is in the L2 power mode. This is the largest individual -- power reduction allowed in the L2 power mode. -- For CTLM solution, the range is 1 ~ 5(dB); -- for BCM solution, the range is 0 ~ 15(dB)." -- ::= { adslLineConfEntry 18 } -- -- adslLineConfL2ATPRT OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "the maximum Aggregate Transmit Power Reduction Total (ATPRT) -- in decibels (dB) that is permitted in the L2 power mode. -- This is the total transmit power decrease that is allowed -- to occur in the L2 power mode. -- For CTLM solution, the range is 1 ~ 40(dB); -- for BCM solution, the range is 0 ~ 15(dB)." -- ::= { adslLineConfEntry 19 } -- -- -- adslLineConfMaxL2Rate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured maximum L2 rate. -- (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" -- ::= { adslLineConfEntry 20 } -- -- adslLineConfMinL2Rate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured minimum L2 rate. -- (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" -- ::= { adslLineConfEntry 21 } -- -- adslLineConfL0toL2Rate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured transition L0 to L2 rate. -- (<=minl2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" -- ::= { adslLineConfEntry 22 } -- ADSL Port Batch Set --adslPortBatchSet OBJECT IDENTIFIER ::= { adslPort 3 } -- -- adslPortTarget OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The managed object is used for identify the target on which -- the port configuration should be performed. The target is encoded as: -- Byte 1: 0, Reserved(chaises) -- Byte 2~3: 0,0 Reserved(slot) -- Byte 4: 0, reserved -- Byte 5~11:each octet specifies a set of eight ports, with the first -- octet specifying ports 1 through 8, etc." -- ::= { adslPortBatchSet 1 } -- -- adslPortOps OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS current -- DESCRIPTION -- "The managed object is for ADSL line configuration. When the EMS -- wants to issue the desired operation, the EMS shall send SNMP-SET message to set -- the corresponding bit value to be 1. The various bit positions are: -- BIT 1: enable port -- BIT 2: disable port -- BIT 3: set ADSL mode -- BIT 4: set line profile -- BIT 5: set alarm profile -- BIT 6: enable Annex L to be narrow mode(Only in AnnexA) -- BIT 7: enable Annex L to be wide mode(Only in AnnexA) -- BIT 8: disable Annex L(Only in AnnexA) -- BIT 9: enable Annex M (For BCM AnnexA solution) -- BIT 10: disable Annex M (For BCM AnnexA solution) -- BIT 11: enable Annex I (For BCM AnnexA solution) -- BIT 12: disable Annex I (For BCM AnnexA solution) -- BIT 13: set option mask -- BIT 14: enable power management mode to be L2 -- BIT 15: enable power management mode to be L3 -- BIT 16: disable power management mode -- BIT 17: set power mode to be fixed -- BIT 18: set power mode to be priority to power -- BIT 19: set power mode to be priority to rate -- BIT 20: set ATU-R max Tx power -- BIT 21: set ATU-C max Tx power -- BIT 22: set max Rx power -- BIT 23: set ATU-R carrier mask -- BIT 24: set ATU-C carrier mask -- BIT 25: set ATU-R INP minimum setting -- BIT 26: set ATU-C INP minimum setting" -- ::= { adslPortBatchSet 2 } -- -- adslPortOps2 OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS current -- DESCRIPTION -- "The managed object is for ADSL line configuration. When the EMS -- wants to issue the desired operation, the EMS shall send SNMP-SET message to set -- the corresponding bit value to be 1. The various bit positions are: -- BIT 1: set L0 Time -- BIT 2: set L2 Time -- BIT 3: set L2 ATPR -- BIT 4: set L2 ATPRT -- BIT 5: set maximum L2 rate -- BIT 6: set minimum L2 rate -- BIT 7: set transition L0 to L2 rate" -- ::= { adslPortBatchSet 3 } -- -- -- adslModeForBatchSet OBJECT-TYPE -- SYNTAX INTEGER { -- gDotLite(1), -- gDotDmt(2), -- t1Dot413(3), -- auto(4), -- etsi(5), -- adsl2(6), -- adsl2Plus(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "G.lite and T1.413 are only applicable to annex A board. -- ETSI is only applicable to annex B board." -- ::= { adslPortBatchSet 4 } -- -- adslLineProfileForBatchSet OBJECT-TYPE -- SYNTAX DisplayString (SIZE (1..31)) -- ACCESS read-write -- STATUS current -- DESCRIPTION -- "The ADSL line profile." -- ::= { adslPortBatchSet 5 } -- -- adslAlarmProfileForBatchSet OBJECT-TYPE -- SYNTAX DisplayString (SIZE (1..31)) -- ACCESS read-write -- STATUS current -- DESCRIPTION -- "The ADSL alarm profile." -- ::= { adslPortBatchSet 6 } -- -- adslOptionMaskForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The semantic for each bit is identical to the object adslLineConfOptionMask." -- ::= { adslPortBatchSet 7 } -- -- adslAturMaxTxPowerForBatchSet OBJECT-TYPE -- SYNTAX INTEGER (-130..200) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum allowed transmit power of ATU-R." -- ::= { adslPortBatchSet 8 } -- -- adslAtucMaxTxPowerForBatchSet OBJECT-TYPE -- SYNTAX INTEGER (-50..200) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum allowed transmit power of ATU-C." -- ::= { adslPortBatchSet 9 } -- -- adslMaxRxPowerForBatchSet OBJECT-TYPE -- SYNTAX INTEGER (-255..255) -- UNITS "tenth dBm" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum aggregate received power." -- ::= { adslPortBatchSet 10 } -- -- adslAturCarrierMaskForBatchSet OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; -- CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. -- Bit set to 1 indicates the bin is masked off." -- ::= { adslPortBatchSet 11 } -- -- adslAtucCarrierMask0ForBatchSet OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates -- the bin is masked off." -- ::= { adslPortBatchSet 12 } -- -- adslAtucCarrierMask1ForBatchSet OBJECT-TYPE -- SYNTAX OCTET STRING -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates -- the bin is masked off." -- ::= { adslPortBatchSet 13 } -- -- adslAturInpForBatchSet OBJECT-TYPE -- SYNTAX INTEGER { -- zero(1), -- zero-point-five(2), -- one(3), -- two(4), -- four(5), -- eight(6), -- sixteen(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. -- For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." -- ::= { adslPortBatchSet 14 } -- -- adslAtucInpForBatchSet OBJECT-TYPE -- SYNTAX INTEGER { -- zero(1), -- zero-point-five(2), -- one(3), -- two(4), -- four(5), -- eight(6), -- sixteen(7) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. -- For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." -- ::= { adslPortBatchSet 15 } -- -- -- adslL0TimeForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set the minimum time in seconds that the ADSL line -- must stay in L0 power mode before changing to the L2 power mode. -- For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535." -- ::= { adslPortBatchSet 16 } -- -- adslL2TimeForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set minimum time in seconds that the ADSL line -- must stay in the L2 power mode before reducing the power -- again in the L2 power mode. -- For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535." -- ::= { adslPortBatchSet 17 } -- -- adslL2ATPRForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Set the maximum Aggregate Transmit Power Reduction (ATPR) -- in decibels (dB) that is permitted in a L2 power reduction. -- The system can gradually decrease the ADSL line transmission power -- while it is in the L2 power mode. This is the largest individual -- power reduction allowed in the L2 power mode. -- For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB)." -- ::= { adslPortBatchSet 18 } -- -- adslL2ATPRTForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "the maximum Aggregate Transmit Power Reduction Total (ATPRT) -- in decibels (dB) that is permitted in the L2 power mode. -- This is the total transmit power decrease that is allowed -- to occur in the L2 power mode. -- For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB)." -- ::= { adslPortBatchSet 19 } -- -- adslMaxL2RateForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured maximum L2 rate. -- (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" -- ::= { adslPortBatchSet 20 } -- -- adslMinL2RateForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured minimum L2 rate. -- (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" -- ::= { adslPortBatchSet 21 } -- -- adslL0toL2RateForBatchSet OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "configured transition L0 to L2 rate. -- (<=minl2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" -- ::= { adslPortBatchSet 22 } -- Line Status -- adslLineStatusTable OBJECT-TYPE -- SYNTAX SEQUENCE OF AdslLineStatusEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table includes the ADSL line status." -- ::= { adslPort 4 } -- --adslLineStatusEntry OBJECT-TYPE -- SYNTAX AdslLineStatusEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in adslLineStatusTable." -- INDEX { ifIndex } -- ::= { adslLineStatusTable 1 } -- -- AdslLineStatusEntry ::= -- SEQUENCE { -- adslLineStatusMode INTEGER, -- adslLineUpTime INTEGER -- } -- -- adslLineStatusMode OBJECT-TYPE -- SYNTAX INTEGER { -- gDotLite(1), -- gDotDmt(2), -- t1Dot413(3), -- etsi(4), -- adsl2(5), -- adsl2Plus(6), -- none(7) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The link up mode of the ADSL line." -- ::= { adslLineStatusEntry 1 } -- -- adslLineUpTime OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The link up time of the ADSL line, in unit of seconds" -- ::= { adslLineStatusEntry 2 } -- Power Mgmt Parameter Table -- powerMgmtParamTable OBJECT-TYPE -- SYNTAX SEQUENCE OF PowerMgmtParamEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table defines L0 to L2 power transition parameters." -- ::= { adslPort 5 } -- --powerMgmtParamEntry OBJECT-TYPE -- SYNTAX PowerMgmtParamEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in powerMgmtParamTable." -- INDEX { ifIndex } -- ::= { powerMgmtParamTable 1 } -- -- PowerMgmtParamEntry ::= -- SEQUENCE { -- powerMgmtL0Time INTEGER, -- powerMgmtL2Time INTEGER, -- powerMgmtL2Atpr INTEGER, -- powerMgmtL2Atprt INTEGER, -- powerMgmtL2MinRate INTEGER, -- powerMgmtL2MaxRate INTEGER, -- powerMgmtL2ThreshRate INTEGER -- } -- -- powerMgmtL0Time OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "second" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the minimum time in L0 mode before L2 mode may be entered." -- ::= { powerMgmtParamEntry 1 } -- --powerMgmtL2Time OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "second" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the minimum time in L2 mode before trimming and in between power trims." -- ::= { powerMgmtParamEntry 2 } -- -- powerMgmtL2Atpr OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum Aggregate Transmit Power Reduction." -- ::= { powerMgmtParamEntry 3 } -- -- powerMgmtL2Atprt OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "dB" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The maximum Aggregate Transmit Power Reduction Total." -- ::= { powerMgmtParamEntry 4 } -- -- powerMgmtL2MinRate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "Kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the minimum L2 rate." -- ::= { powerMgmtParamEntry 5 } -- -- powerMgmtL2MaxRate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "Kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the maximum L2 rate." -- ::= { powerMgmtParamEntry 6 } -- -- powerMgmtL2ThreshRate OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "Kbps" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the rate threshold that triggers the line entering L0 or L2 mode." -- ::= { powerMgmtParamEntry 7 } -- Power Mgmt PSD Table -- Not support in 7324 RU R4.0.2 -- powerMgmtPSDTable OBJECT-TYPE -- SYNTAX SEQUENCE OF PowerMgmtPSDEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table provides the PSD setting for both ATU-C and ATU-R." -- ::= { adslPort 6 } -- --powerMgmtPSDEntry OBJECT-TYPE -- SYNTAX PowerMgmtPSDEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in powerMgmtPSDTable." -- INDEX { ifIndex } -- ::= { powerMgmtPSDTable 1 } -- -- PowerMgmtPSDEntry ::= -- SEQUENCE { -- powerMgmtAtucMaxPSD INTEGER, -- powerMgmtAturMaxPSD INTEGER -- } -- -- powerMgmtAtucMaxPSD OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "0.1dBm/Hz" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the maximum ATU-C PSD." -- ::= { powerMgmtPSDEntry 1 } -- -- powerMgmtAturMaxPSD OBJECT-TYPE -- SYNTAX INTEGER -- UNITS "0.1dBm/Hz" -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The object specifies the maximum ATU-R PSD." -- ::= { powerMgmtPSDEntry 2 } -------------------- -- shdslPort -------------------- -- SHDSL Line Table shdslLineConfTable OBJECT-TYPE SYNTAX SEQUENCE OF ShdslLineConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing the SHDSL line." ::= { shdslPort 1 } shdslLineConfEntry OBJECT-TYPE SYNTAX ShdslLineConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in shdslLineConfTable." INDEX { ifIndex } ::= { shdslLineConfTable 1 } ShdslLineConfEntry ::= SEQUENCE { shdslLineConfShdslMode INTEGER, shdslLineConfPmms INTEGER, shdslLineConfPboMode INTEGER, shdslLineConfPboValue INTEGER, shdslLineConfShdslTCMode INTEGER } shdslLineConfShdslMode OBJECT-TYPE SYNTAX INTEGER { stuc(1), stur(2), auto(3), pam16(4), pam32(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of the SHDSL port." ::= { shdslLineConfEntry 1 } shdslLineConfPmms OBJECT-TYPE SYNTAX INTEGER { normal(1), forced(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Negotiated noise margin mode of the SHDSL port." ::= { shdslLineConfEntry 2 } shdslLineConfPboMode OBJECT-TYPE SYNTAX INTEGER { normalepl(1), forcedepl(2), forcednoepl(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Power backoff mode of the SHDSL port." ::= { shdslLineConfEntry 3 } shdslLineConfPboValue OBJECT-TYPE SYNTAX INTEGER (0..31) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Power backoff value of the SHDSL port." ::= { shdslLineConfEntry 4 } shdslLineConfShdslTCMode OBJECT-TYPE SYNTAX INTEGER { atm(1), efm(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transmission Convergence Mode of the SHDSL port." ::= { shdslLineConfEntry 5 } -- SHDSL Port Batch Set shdslPortBatchSet OBJECT IDENTIFIER ::= { shdslPort 2 } shdslPortTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { shdslPortBatchSet 1 } shdslPortOps OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS current DESCRIPTION "The managed object is for SHDSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set SHDSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: set pmms mode to be normal BIT 7: set pmms mode to be forced BIT 8: set pbo mode to be normalepl BIT 9: set pbo mode to be forcedepl BIT 10: set pbo mode to be forcednoepl BIT 11: set pbo value" ::= { shdslPortBatchSet 2 } shdslModeForBatchSet OBJECT-TYPE SYNTAX INTEGER { stuc(1), stur(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of the SHDSL port." ::= { shdslPortBatchSet 3 } shdslLineProfileForBatchSet OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) ACCESS read-write STATUS current DESCRIPTION "The SHDSL line profile." ::= { shdslPortBatchSet 4 } shdslAlarmProfileForBatchSet OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) ACCESS read-write STATUS current DESCRIPTION "The SHDSL alarm profile." ::= { shdslPortBatchSet 5 } shdslPboValueForBatchSet OBJECT-TYPE SYNTAX INTEGER (0..31) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Power backoff value of the SHDSL port." ::= { shdslPortBatchSet 6 } -------------------- -- pvc -------------------- maxNumOfPvcs OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of PVCs which could be created on a port." ::= { pvc 1 } -- PVC Table pvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes PVC configuration." ::= { pvc 2 } pvcEntry OBJECT-TYPE SYNTAX PvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in pvcTable." INDEX { ifIndex, pvcVpi, pvcVci, pvcPvid } ::= { pvcTable 1 } PvcEntry ::= SEQUENCE { pvcVpi INTEGER, pvcVci INTEGER, pvcPvid VlanIndex, pvcPriority INTEGER, pvcProfileDS DisplayString, pvcRowStatus RowStatus, pvcProfileUS DisplayString } pvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { pvcEntry 1 } pvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { pvcEntry 2 } pvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the pvc." ::= { pvcEntry 3 } pvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the pvc." ::= { pvcEntry 5 } pvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { pvcEntry 6 } pvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { pvcEntry 7 } pvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { pvcEntry 8 } -- Upstream Rate Limit Table pvcUsRateLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF PvcUsRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the upstream rate limit for each PVC." ::= { pvc 4 } pvcUsRateLimitEntry OBJECT-TYPE SYNTAX PvcUsRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in pvcUsRateLimitTable." INDEX { ifIndex, pvcVpi, pvcVci } ::= { pvcUsRateLimitTable 1 } PvcUsRateLimitEntry ::= SEQUENCE { pvcUsRateLimitEnable INTEGER, pvcUsRateLimit INTEGER } pvcUsRateLimitEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable upstream rate limit for a PVC." ::= { pvcUsRateLimitEntry 1 } pvcUsRateLimit OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream rate limit in Kbps for a PVC." ::= { pvcUsRateLimitEntry 2 } -------------------- -- priority pvc -------------------- maxNumOfPriorityPvcs OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of priority PVCs which could be created on a port." ::= { ppvc 1 } -- Priority PVC Table ppvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes priority PVC configuration." ::= { ppvc 2 } ppvcEntry OBJECT-TYPE SYNTAX PpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ppvcTable." INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcPvid } ::= { ppvcTable 1 } PpvcEntry ::= SEQUENCE { ppvcVpi INTEGER, ppvcVci INTEGER, ppvcPvid VlanIndex, ppvcEncap INTEGER, ppvcPriority INTEGER, ppvcRowStatus RowStatus } ppvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the ppvc." ::= { ppvcEntry 1 } ppvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the ppvc." ::= { ppvcEntry 2 } ppvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the ppvc." ::= { ppvcEntry 3 } ppvcEncap OBJECT-TYPE SYNTAX INTEGER { llc(1), vc(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Encapsulation of the ppvc." ::= { ppvcEntry 4 } ppvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the ppvc." ::= { ppvcEntry 5 } ppvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { ppvcEntry 6 } -- Priority PVC Member Table ppvcMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF PpvcMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes priority PVC member configuration." ::= { ppvc 4 } ppvcMemberEntry OBJECT-TYPE SYNTAX PpvcMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ppvcMemberTable." INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcMemberVpi, ppvcMemberVci, ppvcMemberPriority } ::= { ppvcMemberTable 1 } PpvcMemberEntry ::= SEQUENCE { ppvcMemberVpi INTEGER, ppvcMemberVci INTEGER, ppvcMemberPriority INTEGER, ppvcMemberProfileDS DisplayString, ppvcMemberRowStatus RowStatus, ppvcMemberProfileUS DisplayString } ppvcMemberVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the member ppvc." ::= { ppvcMemberEntry 1 } ppvcMemberVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the member ppvc." ::= { ppvcMemberEntry 2 } ppvcMemberPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "802.1p default priority of the member ppvc." ::= { ppvcMemberEntry 3 } ppvcMemberProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The profile of the member ppvc in DS side." ::= { ppvcMemberEntry 4 } ppvcMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { ppvcMemberEntry 5 } ppvcMemberProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The profile of the member ppvc in US side." ::= { ppvcMemberEntry 6 } -------------------- -- portOperation -------------------- portTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { portOperation 1 } portOps OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS current DESCRIPTION "The managed object is for xDSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port" ::= { portOperation 2 } -------------------- -- paepvc -------------------- -- PPPoAoE PVC Table paepvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PaePvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes PPPoAoE PVC configuration." ::= { paepvc 1 } paepvcEntry OBJECT-TYPE SYNTAX PaePvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcTable." INDEX { ifIndex, paepvcVpi, paepvcVci, paepvcPvid } ::= { paepvcTable 1 } PaePvcEntry ::= SEQUENCE { paepvcVpi INTEGER, paepvcVci INTEGER, paepvcPvid VlanIndex, paepvcPriority INTEGER, paepvcProfileDS DisplayString, paepvcAcName DisplayString, paepvcServiceName DisplayString, paepvcHelloTime INTEGER, paepvcRowStatus RowStatus, paepvcProfileUS DisplayString } paepvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { paepvcEntry 1 } paepvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { paepvcEntry 2 } paepvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the pvc." ::= { paepvcEntry 3 } paepvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the pvc." ::= { paepvcEntry 5 } paepvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { paepvcEntry 6 } paepvcAcName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Access concentrator name." ::= { paepvcEntry 7 } paepvcServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service name." ::= { paepvcEntry 8 } paepvcHelloTime OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-create STATUS current DESCRIPTION "The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time." ::= { paepvcEntry 9 } paepvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { paepvcEntry 10 } paepvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { paepvcEntry 11 } -------------------- -- tlspvc -------------------- -- TLS PVC Table tlspvcTable OBJECT-TYPE SYNTAX SEQUENCE OF TlsPvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Transparent LAN Service (TLS) PVC configuration." ::= { tlspvc 1 } tlspvcEntry OBJECT-TYPE SYNTAX TlsPvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of tlspvcTable." INDEX { ifIndex, tlspvcVpi, tlspvcVci, tlspvcSvid } ::= { tlspvcTable 1 } TlsPvcEntry ::= SEQUENCE { tlspvcVpi INTEGER, tlspvcVci INTEGER, tlspvcSvid VlanIndex, tlspvcSpriority INTEGER, tlspvcProfileDS DisplayString, tlspvcRowStatus RowStatus, tlspvcProfileUS DisplayString } tlspvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { tlspvcEntry 1 } tlspvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { tlspvcEntry 2 } tlspvcSvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "s-tag VLAN ID of the pvc." ::= { tlspvcEntry 3 } tlspvcSpriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "s-tag priority of the pvc." ::= { tlspvcEntry 5 } tlspvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { tlspvcEntry 6 } tlspvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { tlspvcEntry 7 } tlspvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { tlspvcEntry 8 } -------------------- -- gbond -------------------- -- gbondTable gbondGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF GbondGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the G.Bond configuration information for each bonding group of the device." ::= { gbond 1 } gbondGroupEntry OBJECT-TYPE SYNTAX GbondGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of gbondTable." INDEX { gbondGroupName } ::= { gbondGroupTable 1 } GbondGroupEntry ::= SEQUENCE { gbondGroupName OCTET STRING, gbondGroupPorts OCTET STRING, gbondGroupSid INTEGER, gbondGroupUpRate Unsigned32, gbondGroupDownRate Unsigned32, gbondGroupRowStatus RowStatus } gbondGroupName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify bonding group." ::= { gbondGroupEntry 1 } gbondGroupPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7. Byte 6~10:Reserved" ::= { gbondGroupEntry 2 } gbondGroupSid OBJECT-TYPE SYNTAX INTEGER { sid8(1), sid12(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the sequence index mode of the bonding group." ::= { gbondGroupEntry 3 } gbondGroupUpRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The UP stream rate." ::= { gbondGroupEntry 4 } gbondGroupDownRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The DOWN stream rate." ::= { gbondGroupEntry 5 } gbondGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { gbondGroupEntry 6 } --------------- -- switch ---------------------------------------- -- enetport OBJECT IDENTIFIER ::= { switch 3 } -- bandwidth OBJECT IDENTIFIER ::= { switch 4 } -- qschedule OBJECT IDENTIFIER ::= { switch 5 } -- dot3ad OBJECT IDENTIFIER ::= { switch 6 } -- stp OBJECT IDENTIFIER ::= { switch 7 } -- bcastCtrl OBJECT IDENTIFIER ::= { switch 8 } -- portIsolation OBJECT IDENTIFIER ::= { switch 9 } dscp OBJECT IDENTIFIER ::= { switch 10 } -- mstp OBJECT IDENTIFIER ::= { switch 11 } vlanIsolation OBJECT IDENTIFIER ::= { switch 12 } enetMtu OBJECT IDENTIFIER ::= { switch 13 } -- managementVLANId OBJECT-TYPE -- SYNTAX VlanIndex -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The VLAN ID for management." -- ::= { switch 1 } -- maxNumOfStaticVlans OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The maximum number of VLANs supported by the system." -- ::= { switch 2 } -------------------- -- dscp -------------------- dscpMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF DscpMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains DSCP mapping configuration for the adsl and ethernet ports." ::= { dscp 1 } dscpMappingEntry OBJECT-TYPE SYNTAX DscpMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dscpMappingTable." INDEX { dscpSrcCodePoint } ::= { dscpMappingTable 1 } DscpMappingEntry ::= SEQUENCE { dscpSrcCodePoint INTEGER, -- dscpMapCodePoint INTEGER, dscpMapPriority INTEGER } dscpSrcCodePoint OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The DSCP source code point used for mapping." ::= { dscpMappingEntry 1 } -- dscpMapCodePoint OBJECT-TYPE -- SYNTAX INTEGER (0..63) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The mapping code point that will replace the source code point in the incoming packet." -- ::= { dscpMappingEntry 2 } dscpMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The mapping p bits that will replace the source p bits in the incoming packet." ::= { dscpMappingEntry 3 } --- pfchen dscpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DscpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains DSCP mapping configuration for the adsl and ethernet ports." ::= { dscp 2 } dscpPortEntry OBJECT-TYPE SYNTAX DscpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dscpPortTable." INDEX { ifIndex } ::= { dscpPortTable 1 } DscpPortEntry ::= SEQUENCE { dscpStatusEnable INTEGER } dscpStatusEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP port status." ::= { dscpPortEntry 1 } -------------------- -- Vlan Isolation -------------------- vlanIsolationTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanIsolationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains configuration of isolated VLAN." ::= { vlanIsolation 1 } vlanIsolationEntry OBJECT-TYPE SYNTAX VlanIsolationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of vlanIsolationTable." INDEX { dot1qVlanIndex } ::= { vlanIsolationTable 1 } VlanIsolationEntry ::= SEQUENCE { vlanIsolationRowStatus INTEGER } vlanIsolationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { vlanIsolationEntry 1 } -------------------- -- enet MTU -------------------- enetMaxMtu OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the maximum MTU size for layer 2 frame, size from 1526 to 1600, default value is 1526." ::= { enetMtu 1 } ---------------------------------------- -- sys ---------------------------------------- -- sysState OBJECT IDENTIFIER ::= { sys 1 } -- sysOperation OBJECT IDENTIFIER ::= { sys 2 } -- hwMonitor OBJECT IDENTIFIER ::= { sys 3 } -- timeSetup OBJECT IDENTIFIER ::= { sys 4 } accessCtrl OBJECT IDENTIFIER ::= { sys 5 } -- syslog OBJECT IDENTIFIER ::= { sys 6 } -- snmp OBJECT IDENTIFIER ::= { sys 7 } extAlarm OBJECT IDENTIFIER ::= { sys 8 } user OBJECT IDENTIFIER ::= { sys 9 } ---------------------------------------- -- slot id ---------------------------------------- sysSlotId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Device slot ID(0...255)." ::= { sys 10 } -------------------- -- Access Control -------------------- -- Secured Client Table securedClientTable OBJECT-TYPE SYNTAX SEQUENCE OF SecuredClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about secured clients." ::= { accessCtrl 2 } securedClientEntry OBJECT-TYPE SYNTAX SecuredClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of secured client entry." INDEX { securedClientIndex } ::= { securedClientTable 1 } SecuredClientEntry ::= SEQUENCE { securedClientIndex INTEGER, securedClientStartIp IpAddress, securedClientEndIp IpAddress, securedClientService INTEGER, securedClientEnable INTEGER } securedClientIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the entry." ::= { securedClientEntry 1 } securedClientStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The starting IP address of the secured client set." ::= { securedClientEntry 2 } securedClientEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The ending IP address of the secured client set." ::= { securedClientEntry 3 } securedClientService OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: ssh BIT 6: snmp." ::= { securedClientEntry 4 } securedClientEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable the entry." ::= { securedClientEntry 5 } ---------------------------------------- --extAlarm ---------------------------------------- extAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains external alarm information." ::= { extAlarm 1 } extAlarmEntry OBJECT-TYPE SYNTAX ExtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of external alarm table." INDEX { extAlarmIndex } ::= { extAlarmTable 1 } ExtAlarmEntry ::= SEQUENCE { extAlarmIndex INTEGER, extAlarmname OCTET STRING, extAlarmstatus OCTET STRING } extAlarmIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the entry." ::= { extAlarmEntry 1 } extAlarmname OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The external alarm name." ::= { extAlarmEntry 2 } extAlarmstatus OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Dispaly 'Normal' or 'Alarm' string" ::= { extAlarmEntry 3 } -------------------- -- User Management -------------------- userAuthMode OBJECT-TYPE SYNTAX INTEGER { local(1), radius(2), localThenRadius(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "User authentication procsssing mode." ::= { user 1 } userAuthServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the authentication server." ::= { user 2 } userAuthServerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The port of the authentication server." ::= { user 3 } userAuthServerSecret OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The secret between the authentication server and the NE for authentication process." ::= { user 4 } -- userTable userTable OBJECT-TYPE SYNTAX SEQUENCE OF UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains user information." ::= { user 5 } userEntry OBJECT-TYPE SYNTAX UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of userTable." INDEX { userName } ::= { userTable 1 } UserEntry ::= SEQUENCE { userName DisplayString, userPassword DisplayString, userPriviledge INTEGER, userRowStatus RowStatus } userName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The user name." ::= { userEntry 1 } userPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The user password." ::= { userEntry 2 } userPriviledge OBJECT-TYPE SYNTAX INTEGER { high(1), middle(2), low(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The user priviledge to decide what operation the user can and cannot do." ::= { userEntry 3 } userRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status used to create or delete a user." ::= { userEntry 4 } userAuthDefaultPriviledge OBJECT-TYPE SYNTAX INTEGER { high(1), middle(2), low(3), deny(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided." ::= { user 6 } stdioTimeout OBJECT-TYPE SYNTAX INTEGER (0..360) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the stdio timeout, 0~360 minutes." ::= { sys 12 } ---------------------------------------- -- statistics ---------------------------------------- dhcpStats OBJECT IDENTIFIER ::= { statistics 11 } paepvcStats OBJECT IDENTIFIER ::= { statistics 12 } -- igmpStats OBJECT IDENTIFIER ::= { statistics 2 } macStats OBJECT IDENTIFIER ::= { statistics 13 } -- adslStats OBJECT IDENTIFIER ::= { statistics 4 } shdslStats OBJECT IDENTIFIER ::= { statistics 14 } -- ipStats OBJECT IDENTIFIER ::= { statistics 6 } -- mstpStats OBJECT IDENTIFIER ::= { statistics 7 } gbondStats OBJECT IDENTIFIER ::= { statistics 51 } -------------------- -- DHCP -------------------- -- dhcpSnoopIpTable dhcpSnoopIpTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the IP addresses and netmasks offered by the DHCP server." ::= { dhcpStats 1 } dhcpSnoopIpEntry OBJECT-TYPE SYNTAX DhcpSnoopIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopIpTable." INDEX { ifIndex, dhcpSnoopIp } ::= { dhcpSnoopIpTable 1 } DhcpSnoopIpEntry ::= SEQUENCE { dhcpSnoopIp IpAddress, dhcpSnoopMac PhysAddress } dhcpSnoopIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped IP address." ::= { dhcpSnoopIpEntry 1 } dhcpSnoopMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped MAC address." ::= { dhcpSnoopIpEntry 2 } -- dhcpSnoopCounterTable dhcpSnoopCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the DHCP statistics." ::= { dhcpStats 2 } dhcpSnoopCounterEntry OBJECT-TYPE SYNTAX DhcpSnoopCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopCounterTable." INDEX { ifIndex } ::= { dhcpSnoopCounterTable 1 } DhcpSnoopCounterEntry ::= SEQUENCE { dhcpDiscovery Counter64, dhcpOffer Counter64, dhcpRequest Counter64, dhcpAck Counter64, dhcpAckBySnoopFull Counter64 } dhcpDiscovery OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP server discovery packets." ::= { dhcpSnoopCounterEntry 1 } dhcpOffer OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP server offer packets." ::= { dhcpSnoopCounterEntry 2 } dhcpRequest OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP request packets." ::= { dhcpSnoopCounterEntry 3 } dhcpAck OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP acknowledge packets." ::= { dhcpSnoopCounterEntry 4 } dhcpAckBySnoopFull OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full." ::= { dhcpSnoopCounterEntry 5 } -- paepvcSessionTable paepvcSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF PaepvcSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the paepvc session statistics." ::= { paepvcStats 1 } paepvcSessionEntry OBJECT-TYPE SYNTAX PaepvcSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcSessionTable." INDEX { ifIndex , paepvcSessionVpi, paepvcSessionVci } ::= { paepvcSessionTable 1 } PaepvcSessionEntry ::= SEQUENCE { paepvcSessionVpi INTEGER, paepvcSessionVci INTEGER, paepvcSessionState INTEGER, paepvcSessionId INTEGER, paepvcSessionUptime Unsigned32, paepvcSessionacname DisplayString, paepvcSessionsrvcname DisplayString } paepvcSessionVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VPI." ::= { paepvcSessionEntry 1 } paepvcSessionVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VCI." ::= { paepvcSessionEntry 2 } paepvcSessionState OBJECT-TYPE SYNTAX INTEGER { down(1), pppoe(2), ppp(3), up(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC status." ::= { paepvcSessionEntry 3 } paepvcSessionId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC session ID." ::= { paepvcSessionEntry 4 } paepvcSessionUptime OBJECT-TYPE SYNTAX Unsigned32 UNITS "second" MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC session uptime." ::= { paepvcSessionEntry 5 } paepvcSessionacname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Access concentrator name." ::= { paepvcSessionEntry 6 } paepvcSessionsrvcname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Service name." ::= { paepvcSessionEntry 7 } -- paepvcCountTable paepvcCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PaepvcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the paepvc counters." ::= { paepvcStats 2 } paepvcCountEntry OBJECT-TYPE SYNTAX PaepvcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcCountTable." INDEX { ifIndex , paepvcCountVpi, paepvcCountVci } ::= { paepvcCountTable 1 } PaepvcCountEntry ::= SEQUENCE { paepvcCountVpi INTEGER, paepvcCountVci INTEGER, paepvcCountPppLcpCfgReqRx Unsigned32, paepvcCountPppLcpEchoReqRx Unsigned32, paepvcCountPppLcpEchoReplyRx Unsigned32, paepvcCountPadiTx Unsigned32, paepvcCountPadoRx Unsigned32, paepvcCountPadrTx Unsigned32, paepvcCountPadsRx Unsigned32, paepvcCountPadtTx Unsigned32, paepvcCountPadtRx Unsigned32, paepvcCountSrvcnameErrRx Unsigned32, paepvcCountAcSystemErrRx Unsigned32, paepvcCountGenericErrTx Unsigned32, paepvcCountGenericErrRx Unsigned32 } paepvcCountVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VPI." ::= { paepvcCountEntry 1 } paepvcCountVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VCI." ::= { paepvcCountEntry 2 } paepvcCountPppLcpCfgReqRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp config-request received." ::= { paepvcCountEntry 3 } paepvcCountPppLcpEchoReqRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp echo-request received." ::= { paepvcCountEntry 4 } paepvcCountPppLcpEchoReplyRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp echo-reply received." ::= { paepvcCountEntry 5 } paepvcCountPadiTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padi transfered" ::= { paepvcCountEntry 6 } paepvcCountPadoRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe pado received" ::= { paepvcCountEntry 7 } paepvcCountPadrTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padr transfered" ::= { paepvcCountEntry 8 } paepvcCountPadsRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe pads received" ::= { paepvcCountEntry 9 } paepvcCountPadtTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padt transfered" ::= { paepvcCountEntry 10 } paepvcCountPadtRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padt received" ::= { paepvcCountEntry 11 } paepvcCountSrvcnameErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe service name error received" ::= { paepvcCountEntry 12 } paepvcCountAcSystemErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe access concentrator name error received" ::= { paepvcCountEntry 13 } paepvcCountGenericErrTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe generic error transfered" ::= { paepvcCountEntry 14 } paepvcCountGenericErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe generic error received" ::= { paepvcCountEntry 15 } -------------------- -- MAC -------------------- macDisplayTarget OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50)." ::= { macStats 1 } -- macTable macTable OBJECT-TYPE SYNTAX SEQUENCE OF MacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame." ::= { macStats 2 } macEntry OBJECT-TYPE SYNTAX MacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macTable." INDEX { macAddress } ::= { macTable 1 } MacEntry ::= SEQUENCE { macAddress MacAddress, macPort INTEGER, macStatus INTEGER } macAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A unicast MAC address for which the bridge has forwarding and/or filtering information." ::= { macEntry 1 } macPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The port from which the mac address has been learned." ::= { macEntry 2 } macStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), learned(3), self(4), mgmt(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this entry." ::= { macEntry 3 } -------------------- -- SHDSL -------------------- -- shdslLinePerfTable shdslLinePerfTable OBJECT-TYPE SYNTAX SEQUENCE OF ShdslLinePerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table displays SHDSL line performance." ::= { shdslStats 1 } shdslLinePerfEntry OBJECT-TYPE SYNTAX ShdslLinePerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of shdslLinePerfTable." INDEX { ifIndex } ::= { shdslLinePerfTable 1 } ShdslLinePerfEntry ::= SEQUENCE { shdslLinePerfEs Counter, shdslLinePerfSes Counter, shdslLinePerfCrc Counter, shdslLinePerfLosws Counter, shdslLinePerfUas Counter, shdslLinePerfSegmentAnomalies Counter, shdslLinePerfSegmentDefect Counter } shdslLinePerfEs OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) on this endpoint since link up." ::= { shdslLinePerfEntry 1 } shdslLinePerfSes OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) on this endpoint since link up." ::= { shdslLinePerfEntry 2 } shdslLinePerfCrc OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies on this endpoint since link up." ::= { shdslLinePerfEntry 3 } shdslLinePerfLosws OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Sync Word (LOSW) Seconds on this endpoint since link up." ::= { shdslLinePerfEntry 4 } shdslLinePerfUas OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) on this endpoint since link up." ::= { shdslLinePerfEntry 5 } shdslLinePerfSegmentAnomalies OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Segment Anomalies on this endpoint since link up." ::= { shdslLinePerfEntry 6 } shdslLinePerfSegmentDefect OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Segment Defects on this endpoint since link up." ::= { shdslLinePerfEntry 7 } -------------------- -- IGMP -------------------- igmpQueryCntTotal OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP query messages received." ::= { statistics 1 } igmpReportCntTotal OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP report messages received." ::= { statistics 2 } igmpLeaveCntTotal OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP leave messages received." ::= { statistics 3 } igmpNumOfActiveGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP learned groups." ::= { statistics 4 } -- igmp Group Table igmpGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes igmp group information." ::= { statistics 5 } igmpGroupEntry OBJECT-TYPE SYNTAX IgmpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in igmpGroupTable." INDEX { igmpGroupIp } ::= { igmpGroupTable 1 } IgmpGroupEntry ::= SEQUENCE { igmpGroupIp IpAddress, igmpGroupvid INTEGER, igmpGroupnumberOfMembers INTEGER, igmpGroupMemberPorts PortList } igmpGroupIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "igmp group IP" ::= { igmpGroupEntry 1 } igmpGroupvid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "vlan id" ::= { igmpGroupEntry 2 } igmpGroupnumberOfMembers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "number Of Members" ::= { igmpGroupEntry 3 } igmpGroupMemberPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Group Member Ports" ::= { igmpGroupEntry 4 } -- igmp Group port Entry igmpGroupPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes igmp Group port information." ::= { statistics 6 } igmpGroupPortEntry OBJECT-TYPE SYNTAX IgmpGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in igmpGroupPortTable." INDEX { ifIndex , igmpGroupPortIp , igmpGroupPortvid} ::= { igmpGroupPortTable 1 } IgmpGroupPortEntry ::= SEQUENCE { igmpGroupPortIp IpAddress, igmpGroupPortvid INTEGER } igmpGroupPortIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Igmp Group IP" ::= { igmpGroupPortEntry 1 } igmpGroupPortvid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Igmp Group vid" ::= { igmpGroupPortEntry 2 } -- igmpGroupTableV2 igmpGroupTableV2 OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupEntryV2 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP learned group member information." ::= { statistics 7 } igmpGroupEntryV2 OBJECT-TYPE SYNTAX IgmpGroupEntryV2 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpGroupTableV2." INDEX { igmpGroupVid, igmpGroupIp } ::= { igmpGroupTableV2 1 } IgmpGroupEntryV2 ::= SEQUENCE { igmpGroupVid VlanIndex, igmpGroupIp IpAddress, igmpGroupNumOfMembers INTEGER, igmpGroupMemberPorts PortList } igmpGroupVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP group VLAN ID." ::= { igmpGroupEntryV2 1 } igmpGroupIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast IP address." ::= { igmpGroupEntryV2 2 } igmpGroupNumOfMembers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of member ports in the group." ::= { igmpGroupEntryV2 3 } igmpGroupMemberPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The member port list of the group." ::= { igmpGroupEntryV2 4 } -- igmpGroupPortTableV2 igmpGroupPortTableV2 OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupPortEntryV2 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP joined groups in this port." ::= { statistics 8 } igmpGroupPortEntryV2 OBJECT-TYPE SYNTAX IgmpGroupPortEntryV2 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpGroupPortTableV2." INDEX { ifIndex, igmpGroupPortVid, igmpGroupPortIp, igmpGroupPortSourceIp } ::= { igmpGroupPortTableV2 1 } IgmpGroupPortEntryV2 ::= SEQUENCE { igmpGroupPortVid VlanIndex, igmpGroupPortIp IpAddress, igmpGroupPortSourceIp IpAddress } igmpGroupPortVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP group VLAN ID." ::= { igmpGroupPortEntryV2 1 } igmpGroupPortIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast IP address." ::= { igmpGroupPortEntryV2 2 } igmpGroupPortSourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address that joins the IGMP group." ::= { igmpGroupPortEntryV2 3 } -- igmpPortCtrlPduTable igmpPortCtrlPduTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpPortCtrlPduEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP related counter values in this port." ::= { statistics 9 } igmpPortCtrlPduEntry OBJECT-TYPE SYNTAX IgmpPortCtrlPduEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpPortCtrlPduTable." INDEX { ifIndex } ::= { igmpPortCtrlPduTable 1 } IgmpPortCtrlPduEntry ::= SEQUENCE { igmpPortCtrlPduQueryCnt Counter, igmpPortCtrlPduReportCnt Counter, igmpPortCtrlPduLeaveCnt Counter, igmpPortNumOfActiveGroups INTEGER } igmpPortCtrlPduQueryCnt OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP query messages received in this port." ::= { igmpPortCtrlPduEntry 1 } igmpPortCtrlPduReportCnt OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP report messages received in this port." ::= { igmpPortCtrlPduEntry 2 } igmpPortCtrlPduLeaveCnt OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP leave messages received in this port." ::= { igmpPortCtrlPduEntry 3 } igmpPortNumOfActiveGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of active IGMP groups in this port." ::= { igmpPortCtrlPduEntry 4 } -------------------- -- G.Bond State -------------------- -- gbondStateTable gbondStateTable OBJECT-TYPE SYNTAX SEQUENCE OF GbondStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the G.Bond configuration information for each bonding group of the device." ::= { gbondStats 1 } gbondStateEntry OBJECT-TYPE SYNTAX GbondStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of gbondTable." INDEX { gbondStateName } ::= { gbondStateTable 1 } GbondStateEntry ::= SEQUENCE { gbondStateName OCTET STRING, gbondStateSid INTEGER, gbondStateUpRate Unsigned32, gbondStateDownRate Unsigned32, gbondStateMember OCTET STRING, gbondStatelinkup OCTET STRING, gbondStateTx OCTET STRING, gbondStateRx OCTET STRING, gbondStatelinkdown OCTET STRING } gbondStateName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "An administratively assigned string, which identifies the bonding group." ::= { gbondStateEntry 1 } gbondStateSid OBJECT-TYPE SYNTAX INTEGER { sid8(1), sid12(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the sequence index mode of the bonding group." ::= { gbondStateEntry 2 } gbondStateUpRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current up stream rate." ::= { gbondStateEntry 3 } gbondStateDownRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current down stream rate." ::= { gbondStateEntry 4 } gbondStateMember OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the port is a member port of the bonding group. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." ::= { gbondStateEntry 5 } gbondStatelinkup OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the link status of port is bidirectional. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." ::= { gbondStateEntry 6 } gbondStateTx OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the link status of port is Tx only. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." ::= { gbondStateEntry 7 } gbondStateRx OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the link status of port is Rx only. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." ::= { gbondStateEntry 8 } gbondStatelinkdown OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the link status of the port is down. The target is encoded as: Byte 1: the octet specifies a set of eight Chassis, Chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5: Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7." ::= { gbondStateEntry 9 } ---------------------------------------- -- clear ---------------------------------------- counterClearTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { clear 1 } counterClearOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters" ::= { clear 2 } counterClearVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "VPI of the pvc whose counters would be cleared." ::= { clear 3 } counterClearVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "VCI of the pvc whose counters would be cleared." ::= { clear 4 } ---------------------------------------- -- trap ---------------------------------------- object OBJECT IDENTIFIER ::= { trap 1 } -- dsl OBJECT IDENTIFIER ::= { trap 2 } equipment OBJECT IDENTIFIER ::= { trap 3 } systrap OBJECT IDENTIFIER ::= { trap 4 } -- enet OBJECT IDENTIFIER ::= { trap 5 } -------------------- -- object -------------------- eqptAlarmInputIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of alarm input." ::= { object 2 } eqptAlarmInputName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Name of alarm input." ::= { object 8 } sysMacAntiSpoofOrig OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Original port of Mac-AntiSpoofing." ::= { object 9 } sysMacAntiSpoofNew OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The New port of Mac-AntiSpoofing." ::= { object 10 } sysMacAntiSpoofMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC of Mac-AntiSpoofing." ::= { object 11 } -------------------- -- equipment -------------------- eqptHWMonitorFailure NOTIFICATION-TYPE STATUS current DESCRIPTION "Hardware monitor diagnosis is failed." ::= { equipment 1 } -------------------- -- systrap -------------------- sysMacAntiSpoofing NOTIFICATION-TYPE OBJECTS { sysMacAntiSpoofOrig, sysMacAntiSpoofNew, sysMacAntiSpoofMAC } STATUS current DESCRIPTION "MAC Anti-spoofing." ::= { systrap 1 } sysAlarmCutoffEnable NOTIFICATION-TYPE STATUS current DESCRIPTION "Alarm cutoff is activated." ::= { systrap 2 } sysAlarmClearEnable NOTIFICATION-TYPE STATUS current DESCRIPTION "Alarm clear is activated." ::= { systrap 3 } sysLoginFailure NOTIFICATION-TYPE STATUS current DESCRIPTION "User login is failed." ::= { systrap 4 } ------------------------------- -- 2684 routed mode pvc (rpvc) ------------------------------- -- Routed Gateway Table rpvcGatewayTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcGatewayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Routed Gateway configuration." ::= { rpvc 1 } rpvcGatewayEntry OBJECT-TYPE SYNTAX RpvcGatewayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in Routed Gateway table." INDEX { rpvcGatewayIp } ::= { rpvcGatewayTable 1 } RpvcGatewayEntry ::= SEQUENCE { rpvcGatewayIp IpAddress, rpvcGatewayVlanId VlanIndex, rpvcGatewayRowStatus RowStatus, rpvcGatewayPriority INTEGER } rpvcGatewayIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP of RPVC gateway." ::= { rpvcGatewayEntry 1 } rpvcGatewayVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan id send to this RPVC gateway." ::= { rpvcGatewayEntry 2 } rpvcGatewayRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcGatewayEntry 3 } rpvcGatewayPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "802.1p p bit send to this RPVC gateway." ::= { rpvcGatewayEntry 4 } -- Routed PVC Table rpvcTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes RPVC configuration." ::= { rpvc 2 } rpvcTableEntry OBJECT-TYPE SYNTAX RpvcTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in rpvcTable." INDEX { ifIndex, rpvcVpi, rpvcVci, rpvcIp, rpvcNetmask } ::= { rpvcTable 1 } RpvcTableEntry ::= SEQUENCE { rpvcVpi INTEGER, rpvcVci INTEGER, rpvcDSProfile DisplayString, rpvcUSProfile DisplayString, rpvcIp IpAddress, rpvcNetmask IpAddress, rpvcGatewayIpAddress IpAddress, rpvcRowStatus RowStatus } rpvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the rpvc." ::= { rpvcTableEntry 1 } rpvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the rpvc." ::= { rpvcTableEntry 2 } rpvcDSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The down stream profile of the rpvc." ::= { rpvcTableEntry 3 } rpvcUSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The up stream profile of the rpvc." ::= { rpvcTableEntry 4 } rpvcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP of the rpvc." ::= { rpvcTableEntry 5 } rpvcNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP mask of the rpvc IP." ::= { rpvcTableEntry 6 } rpvcGatewayIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The gateway IP of rpvc." ::= { rpvcTableEntry 7 } rpvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcTableEntry 8 } -- Routed PVC Routed Domain Table rpvcRouteDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcRouteDomainTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes RPVC route domain configuration." ::= { rpvc 3 } rpvcRouteDomainTableEntry OBJECT-TYPE SYNTAX RpvcRouteDomainTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in rpvcRouteDomainTable." INDEX { ifIndex, rpvcRouteDomainVpi, rpvcRouteDomainVci, rpvcRouteDomainIp, rpvcRouteDomainNetmask } ::= { rpvcRouteDomainTable 1 } RpvcRouteDomainTableEntry ::= SEQUENCE { rpvcRouteDomainVpi INTEGER, rpvcRouteDomainVci INTEGER, rpvcRouteDomainIp IpAddress, rpvcRouteDomainNetmask IpAddress, rpvcRouteDomainRowStatus RowStatus } rpvcRouteDomainVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the rpvc." ::= { rpvcRouteDomainTableEntry 1 } rpvcRouteDomainVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the rpvc." ::= { rpvcRouteDomainTableEntry 2 } rpvcRouteDomainIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The route domain IP." ::= { rpvcRouteDomainTableEntry 3 } rpvcRouteDomainNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP mask of the route domain IP." ::= { rpvcRouteDomainTableEntry 4 } rpvcRouteDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcRouteDomainTableEntry 5 } rpvcArpAgingTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg." ::= { rpvc 4 } rpvcArpFlush OBJECT-TYPE SYNTAX INTEGER { enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Flush the RPVC ARP proxy table." ::= { rpvc 5 } -- DS Bcast diable control Table dsBcastDisableTable OBJECT-TYPE SYNTAX SEQUENCE OF DsBcastDisableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Down Stream Bcast configuration." ::= { port 9 } dsBcastDisableEntry OBJECT-TYPE SYNTAX DsBcastDisableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in Down Stream Bcast table." INDEX { ifIndex, dsBcastDisableVlanId } ::= { dsBcastDisableTable 1 } DsBcastDisableEntry ::= SEQUENCE { dsBcastDisableVlanId INTEGER, dsBcastDisableRowStatus RowStatus } dsBcastDisableVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "downstream broadcast disabled vid." ::= { dsBcastDisableEntry 1 } dsBcastDisableRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { dsBcastDisableEntry 2 } END