5053 lines
176 KiB
Plaintext
5053 lines
176 KiB
Plaintext
-- Copyright (C) 2006-2012 Aricent Group . All Rights Reserved
|
|
|
|
ARICENT-ISS-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE,
|
|
Counter32,enterprises, IpAddress, Integer32, Unsigned32, NOTIFICATION-TYPE
|
|
FROM SNMPv2-SMI
|
|
InterfaceIndex FROM IF-MIB
|
|
RowStatus, TruthValue, DisplayString,
|
|
TEXTUAL-CONVENTION, MacAddress, StorageType FROM SNMPv2-TC
|
|
InetAddress, InetAddressType FROM INET-ADDRESS-MIB;
|
|
|
|
iss MODULE-IDENTITY
|
|
LAST-UPDATED "202203310000Z"
|
|
ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE"
|
|
CONTACT-INFO "support@aricent.com"
|
|
DESCRIPTION
|
|
"The MIB for ISS."
|
|
|
|
REVISION "202203310000Z"
|
|
DESCRIPTION
|
|
"The object issPortCtrlForceSpeed was added"
|
|
|
|
REVISION "202201210000Z"
|
|
DESCRIPTION
|
|
"Was added object issHttpMaxSessions for setting HTTP max sessions"
|
|
|
|
REVISION "202201120000Z"
|
|
DESCRIPTION
|
|
"The default value of MIB 'issLoginLockTime' was changed from 30 to 600."
|
|
|
|
REVISION "201209050000Z"
|
|
DESCRIPTION
|
|
"The MIB for ISS."
|
|
|
|
::= { enterprises futuresoftware (2076) 81 }
|
|
|
|
|
|
PortList ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each octet within this value specifies a set of eight
|
|
ports, with the first octet specifying ports 1 through
|
|
8, the second octet specifying ports 9 through 16, etc.
|
|
Within each octet, the most significant bit represents
|
|
the lowest numbered port, and the least significant bit
|
|
represents the highest numbered port. Thus, each port
|
|
of the bridge is represented by a single bit within the
|
|
value of this object. If that bit has a value of '1'
|
|
then that port is included in the set of ports; the port
|
|
is not included if its bit has a value of '0'."
|
|
SYNTAX OCTET STRING
|
|
|
|
|
|
-- ----------------------------------------------------------------- --
|
|
-- groups in the MIB
|
|
-- ----------------------------------------------------------------- --
|
|
|
|
issNotifications OBJECT IDENTIFIER ::= { iss 0 }
|
|
issSystem OBJECT IDENTIFIER ::= { iss 1 }
|
|
issConfigControl OBJECT IDENTIFIER ::= { iss 2 }
|
|
issMirror OBJECT IDENTIFIER ::= { iss 3 }
|
|
issRateControl OBJECT IDENTIFIER ::= { iss 4 }
|
|
issL2Filter OBJECT IDENTIFIER ::= { iss 5 }
|
|
issL3Filter OBJECT IDENTIFIER ::= { iss 6 }
|
|
issIpAuthMgr OBJECT IDENTIFIER ::= { iss 7 }
|
|
issExt OBJECT IDENTIFIER ::= { iss 8 }
|
|
issL4Switching OBJECT IDENTIFIER ::= { iss 9 }
|
|
issSystemTrap OBJECT IDENTIFIER ::= { iss 10 }
|
|
issAuditTrap OBJECT IDENTIFIER ::= { iss 11 }
|
|
issModule OBJECT IDENTIFIER ::= { iss 12 }
|
|
issSwitchFan OBJECT IDENTIFIER ::= { iss 13 }
|
|
issAclNp OBJECT IDENTIFIER ::= { iss 14 }
|
|
issAclTrafficControl OBJECT IDENTIFIER ::= { iss 15 }
|
|
issLogTrap OBJECT IDENTIFIER ::= { iss 16 }
|
|
issHealthCheckGroup OBJECT IDENTIFIER ::= { iss 17 }
|
|
|
|
-- ---------------------------------------------------------------- --
|
|
|
|
-- System Group
|
|
|
|
-- System Information
|
|
|
|
issSwitchName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..15))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"System name used for identification of the device."
|
|
DEFVAL { "ISS" }
|
|
::= { issSystem 1 }
|
|
issHardwareVersion OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..15))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Version number of the Hardware."
|
|
DEFVAL { "" }
|
|
::= { issSystem 2 }
|
|
issFirmwareVersion OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..15))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Version number of the Firmware."
|
|
DEFVAL { "" }
|
|
::= { issSystem 3 }
|
|
|
|
issDefaultIpAddrCfgMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
manual(1),
|
|
dynamic(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the means by which the default interface in the device
|
|
gets the IP address.
|
|
|
|
If 'manual' mode is selected, the default interface takes the
|
|
'issDefaultIpAddr' configured in the system.
|
|
|
|
If 'dynamic' mode is selected, the default interface gets the IP address
|
|
through dynamic IP address configuration protocols such as RARP client,
|
|
BootP client, DHCP Client, etc.
|
|
|
|
If the system fails to get the IP address dynamically through all the
|
|
above protocols, the default interface uses the 'issDefaultIpAddr'
|
|
configured in the system."
|
|
DEFVAL { manual }
|
|
::= { issSystem 4 }
|
|
|
|
issDefaultIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Default IP Address of the system.
|
|
|
|
This IP address, if modified, will take effect only when the
|
|
configuration is stored & restored."
|
|
::= { issSystem 5 }
|
|
|
|
issDefaultIpSubnetMask OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"IP subnet mask for the default IP address.
|
|
|
|
This subnet mask, if modified, will take effect only when the
|
|
configuration is stored & restored."
|
|
::= { issSystem 6 }
|
|
|
|
issEffectiveIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Effective IP address of the switch to be used for contacting
|
|
through SNMP interface or web interface.
|
|
|
|
This IP address will be same as the default IP address if the
|
|
device fails to get the IP address dynamically or the
|
|
'DefaultIpAddrCfgMode' is 'manual'.
|
|
|
|
This IP address will be different from the default IP address
|
|
if the device manages to get the IP address dynamically.
|
|
|
|
In either condition, this is the effective IP address to be
|
|
used for contacting the switch."
|
|
::= { issSystem 7 }
|
|
|
|
issDefaultInterface OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..24))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Name of the default interface that can be used for
|
|
communicating with the system for configuration through SNMP
|
|
or WebInterface.
|
|
|
|
The default interface, if modified, will take effect only when
|
|
the configuration is stored & restored."
|
|
DEFVAL { "eth0" }
|
|
::= { issSystem 8 }
|
|
|
|
issRestart OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object allows the user to restart the Switch
|
|
(i.e)the entire switch will operationally go down and
|
|
start again. Setting a value of 'true' causes the switch
|
|
to be restarted.
|
|
|
|
When the switch operationally goes down, configuration
|
|
save operation is initiated based on the configuration save
|
|
option chosen.
|
|
|
|
When the switch operationally come up, the saved configurations
|
|
are restored based on the restore option chosen.
|
|
|
|
Once the switch is restarted, the value of this object reverts
|
|
to 'false'."
|
|
DEFVAL { false }
|
|
::= { issSystem 9 }
|
|
|
|
-- Configurtion Save related configuration / information
|
|
|
|
issConfigSaveOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
noSave(1),
|
|
flashSave(2),
|
|
remoteSave(3),
|
|
startupConfig(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies whether the configurations of the switch has to be
|
|
saved or not.
|
|
|
|
The value 'noSave' specifies that the configurations need
|
|
not be saved.
|
|
|
|
The value 'flashSave' specifies that the configurations need
|
|
to be saved in flash in the specified file name issConfigSaveFileName.
|
|
|
|
The value 'remoteSave' specifies that the configurations need
|
|
to be saved in specified remote system.
|
|
|
|
The value 'startupConfig' specifies that the configurations need
|
|
to be saved in flash in the 'Startup Configuration File'.
|
|
|
|
When the issConfigIncrSaveFlag and the issConfigAutoSaveTrigger are set
|
|
as true then the default value of issConfigSaveOption is startupConfig.
|
|
When issConfigIncrSaveFlag is set as false or when
|
|
issConfigAutoSaveTrigger is set as false then the default value of
|
|
issConfigSaveOption is noSave."
|
|
DEFVAL { noSave }
|
|
::= { issSystem 10 }
|
|
|
|
issConfigSaveIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"IP Address of the remote system to which the switch
|
|
configurations have to be saved.
|
|
|
|
This object is valid only if 'issConfigSaveOption' is chosen to be
|
|
'remoteSave'. This object is deprecated, as this object supports only
|
|
IPv4, this IP can be set through issConfigSaveIpvxAddr object and object
|
|
issConfigSaveIpvxAddrType will be set to 1 i.e. IPv4"
|
|
::= { issSystem 11 }
|
|
|
|
issConfigSaveFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Name of the file in which the switch configurations are
|
|
to be saved.
|
|
|
|
This object is valid only if 'issConfigSaveOption' is chosen
|
|
to be 'flashSave' or 'remoteSave'."
|
|
DEFVAL { "iss.conf" }
|
|
::= { issSystem 12 }
|
|
|
|
issInitiateConfigSave OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set as 'true' switch configurations save operation is
|
|
initiated.
|
|
As soon as the configuration save operation is completed, the value
|
|
of this object reverts back to 'false'.
|
|
|
|
All the configurations made via the three interfaces
|
|
viz.
|
|
-> commandline interface
|
|
-> Web Interface
|
|
-> SNMP interface
|
|
are saved either in 'Startup Configuration File' in the flash or
|
|
in the specified 'issConfigSaveFileName' in the flash or
|
|
in the chosen remote system, depending upon 'ConfigSaveOption'."
|
|
DEFVAL { false }
|
|
::= { issSystem 13 }
|
|
|
|
issConfigSaveStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
saveInProgress(1),
|
|
saveSuccessful(2),
|
|
saveFailed(3),
|
|
notInitiated(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Status of configuration save operation."
|
|
DEFVAL { notInitiated }
|
|
::= { issSystem 14 }
|
|
|
|
|
|
-- Configuration Restoration related configuration / information
|
|
|
|
issConfigRestoreOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
noRestore(1),
|
|
restore(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies whether the switch configurations have to be restored
|
|
or not.
|
|
|
|
The value 'noRestore' specifies that the switch configurations
|
|
need not be restored when the system is restarted.
|
|
|
|
The value 'restore' specifies that the configurations
|
|
need to be restored from the 'Startup Configuration File' in the flash
|
|
when the system is restarted."
|
|
DEFVAL { noRestore }
|
|
::= { issSystem 15 }
|
|
|
|
issConfigRestoreIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"IP Address of the remote system from where the switch configurations
|
|
have to be downloaded to the 'Startup Configuration File' in the flash.
|
|
This object is deprecated, as this object supports only IPv4,
|
|
this IP can be set through issConfigRestoreIpvxAddr object and object
|
|
issConfigRestoreAddrType will be set to 1 i.e. IPv4"
|
|
::= { issSystem 16 }
|
|
|
|
issConfigRestoreFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The configuration file name in the remote system which has to be
|
|
downloaded to the 'Startup Configuration File' in the flash."
|
|
DEFVAL { "iss.conf" }
|
|
::= { issSystem 17 }
|
|
|
|
issInitiateConfigRestore OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set as 'true', the switch configurations will be downloaded
|
|
from the specified remote system to the 'Startup Configuration File'
|
|
in the flash.
|
|
|
|
As soon as the configuration download operation is completed, the value
|
|
of this object reverts back to 'false'."
|
|
|
|
DEFVAL { false }
|
|
::= { issSystem 18 }
|
|
|
|
|
|
issConfigRestoreStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
restoreInprogress(1),
|
|
restoreSuccessful(2),
|
|
restoreFailed(3),
|
|
notInitiated(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of the switch configuration restore operation."
|
|
DEFVAL { notInitiated }
|
|
::= { issSystem 19 }
|
|
|
|
|
|
-- Image Downloading related configuration / information
|
|
|
|
issDlImageFromIp OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The Ip Address of machine from where the image has to be downloaded.
|
|
This object is deprecated, as this object supports only
|
|
IPv4, this IP can be set through issDlImageFromIpvxAddr object and object
|
|
issDlImageFromIpAddrType will be set to 1 i.e. IPv4"
|
|
::= { issSystem 20 }
|
|
|
|
issDlImageName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The image name which is to be downloaded to the switch."
|
|
DEFVAL { "iss.exe" }
|
|
::= { issSystem 21 }
|
|
|
|
issInitiateDlImage OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Initiates the Image Download operation."
|
|
::= { issSystem 22 }
|
|
|
|
|
|
|
|
-- Event logging related configuration / information
|
|
|
|
issLoggingOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
console(1),
|
|
file(2),
|
|
flash(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Logging option specifying whether the logging is to be
|
|
done at console or to a file(system buffer) in the system.
|
|
Flash specifies the logging of traces into a file."
|
|
DEFVAL { console }
|
|
::= { issSystem 23 }
|
|
|
|
issUploadLogFileToIp OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The Ip Address of machine to which the log file is to be uploaded.
|
|
This object is deprecated, as this object supports only
|
|
IPv4, this IP can be set through issUploadLogFileToIpvxAddr object and
|
|
object issUploadLogFileToAddrType will be set to 1 i.e. IPv4"
|
|
::= { issSystem 24 }
|
|
|
|
issLogFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The file name to be used for uploading the logs from 'file' to the
|
|
remote system.
|
|
|
|
This object is useful only when the 'LogOption' is chosen as 'file'."
|
|
DEFVAL { "iss.log" }
|
|
::= { issSystem 25 }
|
|
|
|
issInitiateUlLogFile OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Initiates uploading of Log File to the specified IP address in
|
|
'issUploadLogFileToIp'.
|
|
|
|
The logs will be uploaded in the specified 'issLogFileName'."
|
|
::= { issSystem 26 }
|
|
|
|
-- Remote save status
|
|
|
|
issRemoteSaveStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
inprogress(1),
|
|
successful(2),
|
|
failed(3),
|
|
notInitiated(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Status of remote save operation.
|
|
|
|
The remote save operation could be a
|
|
a) configuration file save to remote system
|
|
b) log file upload to remote system."
|
|
DEFVAL { notInitiated }
|
|
::= { issSystem 27 }
|
|
|
|
-- Download status
|
|
|
|
issDownloadStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
inprogress(1),
|
|
successful(2),
|
|
failed(3),
|
|
configDefaultNeeded(4),
|
|
configDefaultInProgress(5),
|
|
configDeafultAborted(6),
|
|
notInitiated(7)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of the Image download operation to the switch."
|
|
DEFVAL { notInitiated }
|
|
::= { issSystem 28 }
|
|
|
|
issSysContact OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..50))
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The textual identification of the contact person for this
|
|
managed node, together with information on how to contact
|
|
this person. If no contact information is known, the value
|
|
is the zero-length string."
|
|
::= { issSystem 29 }
|
|
|
|
issSysLocation OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..50))
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The physical location of this node (e.g., `telephone
|
|
closet, 3rd floor'). If the location is unknown, the value
|
|
is the zero-length string."
|
|
::= { issSystem 30 }
|
|
|
|
-- Login Authentication mechanism
|
|
|
|
issLoginAuthentication OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
local(1),
|
|
remoteRadius(2),
|
|
remoteTacacs(3),
|
|
radiusFallbackToLocal(4),
|
|
tacacsFallbackToLocal(5),
|
|
ldap(6)
|
|
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configures the mechanism by which the user login has to be authenticated
|
|
for accessing the GUI to manage the switch. Authentication is done
|
|
either locally or in the remote side through a RADIUS Server or TACACS.
|
|
If Authentication is configured as radiusLocal or tacacsLocal then
|
|
Local authentication provides a back door or a secondary option
|
|
for authentication if the server fails."
|
|
|
|
DEFVAL { local }
|
|
::= { issSystem 31 }
|
|
|
|
issSwitchBaseMacAddress OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Ethernet address (base address) of the Switch.
|
|
This base Mac Address, if modified, will take effect only when the
|
|
Switch is restarted."
|
|
|
|
DEFVAL { '000102030405'h }
|
|
::= { issSystem 32 }
|
|
|
|
|
|
|
|
-- OOB Interface Existence
|
|
|
|
issOOBInterface OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates wheteher OOB Interface Exists in the System"
|
|
::= { issSystem 33 }
|
|
|
|
|
|
|
|
issSwitchDate OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..40))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
|
|
" The date is configured in the switch in the format,
|
|
Hours:Minutes:Seconds Day Month Year
|
|
e.g 19:10:31 11 08 2005
|
|
|
|
01-12 Month - beginning from January to December
|
|
The railway time 00 to 24 hours can be configured and
|
|
displayed.
|
|
The Display of the date is in the format ,
|
|
WeekDay Month Day Hours:Minutes:Seconds Year
|
|
e.g 04 09 21 18:11:30 2005
|
|
|
|
01-07 WeekDay - beginning from Sunday to Saturday
|
|
01-12 Month - beginning from January to December "
|
|
|
|
::= { issSystem 34 }
|
|
|
|
issNoCliConsole OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates whether the CLI console prompt will be made available
|
|
to the user for the session through serial console. When set to
|
|
TRUE CLI prompt will be available in serial console, when set to
|
|
FALSE CLI prompt will NOT be available in serial console session,
|
|
for the value to take effect, the switch must be restarted,
|
|
the value does not affect the availability of ISS CLI prompt in
|
|
sessions established through Telnet."
|
|
::= { issSystem 35 }
|
|
|
|
issDefaultIpAddrAllocProtocol OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
rarp(1),
|
|
dhcp(2),
|
|
bootp(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the protocol to be used to obtain IP address for this
|
|
interface. This object is valid only when issDefaultIpAddrCfgMode
|
|
is set to dynamic (2). Currently rarp (1) option is not supported."
|
|
DEFVAL { dhcp }
|
|
::= { issSystem 36 }
|
|
|
|
issHttpPort OBJECT-TYPE
|
|
SYNTAX Integer32 (0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The port to be used by the hosts/PC to configure ISS using the Web Interface.
|
|
The HTTP server must be disabled before this configuration is done"
|
|
DEFVAL { 80 }
|
|
|
|
::= { issSystem 37 }
|
|
|
|
issHttpStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for enabling or disabling HTTP in the system."
|
|
|
|
DEFVAL { enable }
|
|
::= { issSystem 38 }
|
|
|
|
issConfigRestoreFileVersion OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..12))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Config Restoration file version. This version will be compared in each
|
|
reboot against version stored in restoration file. Restoration
|
|
will occur only if the first field in restoration file is this OID and the
|
|
RestoreFileVersion value also matches."
|
|
::= { issSystem 39 }
|
|
|
|
issDefaultRmIfName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..23))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Name of the default RM interface that can be used for
|
|
communication between the Active and Standby nodes for
|
|
providing redundancy support.The default RM interface,
|
|
if modified, will take effect only when the switch is
|
|
restarted"
|
|
DEFVAL { "NONE" }
|
|
::= { issSystem 40 }
|
|
|
|
issDefaultVlanId OBJECT-TYPE
|
|
SYNTAX Integer32 (1..4094)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Default VLAN Identifier to be used at system startup.
|
|
The VLAN Module creates this vlan as the default vlan.
|
|
The Default VLAN Identifier, if modified, will take effect
|
|
only when the switch is restarted.
|
|
|
|
It is not advisable to change the default VLAN ID when some
|
|
configurations are already saved.
|
|
|
|
Once the Default VLAN Id is configured, the switch has to
|
|
be restarted before saving any configuration.
|
|
"
|
|
DEFVAL { 1 }
|
|
::= { issSystem 41 }
|
|
|
|
issNpapiMode OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..15))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Mode of NPAPI Processing. It can be
|
|
1. Synchronous, 2. Asynchronous."
|
|
DEFVAL { "Synchronous" }
|
|
::= { issSystem 42 }
|
|
|
|
|
|
issConfigAutoSaveTrigger OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set as 'true', automatic save operation is enabled. i.e., every
|
|
configuration is saved automatically.
|
|
When set as 'false', automatic save operation is disabled. i.e.,
|
|
configuration done will not be save automatically.
|
|
IncrSave is ON : auto save can be enabled /disabled in the system.
|
|
IncrSave is OFF : auto save can be enabled /disabled in the system,
|
|
No effect in the system behaviour(in this case no
|
|
update trigger is generated towards MSR).
|
|
============================================================================
|
|
issConfig issConfig
|
|
incrSaveFlag AutoSaveOption Behaviour
|
|
============================================================================
|
|
TRUE TRUE Data is added to RB Tree and based on save option
|
|
data is added to remote/local incremental file.
|
|
|
|
TRUE FALSE Data is added to RB tree only.
|
|
|
|
FALSE xx in this case no update trigger is generated towards
|
|
MSR.
|
|
============================================================================
|
|
|
|
To enable issConfigAutoSaveTrigger, the issConfigIncrSaveFlag has to be
|
|
enabled.
|
|
The configuration update to issConfigIncrSaveFlag will become applicable
|
|
only after switch restart.
|
|
When issConfigIncrSaveFlag is enabled, the configuration of
|
|
issConfigAutoSaveTrigger will be immediately reflected in the system.
|
|
|
|
"
|
|
|
|
DEFVAL { false }
|
|
::= { issSystem 43 }
|
|
|
|
issConfigIncrSaveFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates whether SNMP Update Trigger for Incremental Save shall be generated or not.
|
|
'True' value implies that the update trigger shall be generated each time a nmhSet
|
|
operation is successful.
|
|
'False' value implies that the update trigger shall not be generated at all.
|
|
|
|
Following table explains the combinations of various configurations
|
|
============================================================================
|
|
issConfig issConfig issConfig
|
|
IncrSaveFlag AutoSaveTrigger SaveOption Behaviour
|
|
============================================================================
|
|
TRUE TRUE Remote Save tftp to remote (on every update trigger)
|
|
TRUE FALSE Remote Save tftp to remote (operator triggered)
|
|
FALSE xx Remote Save tftp to remote (operator triggered)
|
|
TRUE TRUE Flash Save save to local (on every update trigger)
|
|
TRUE FALSE Flash Save save to local (operator triggered)
|
|
FALSE xx Flash Save save to local (operator triggered)
|
|
TRUE TRUE No Save Data added to RB Tree
|
|
TRUE FALSE No Save Data added to RB Tree
|
|
FALSE xx No Save No Update trigger is sent to MSR
|
|
============================================================================
|
|
|
|
The configuration of the issConfigIncrSaveFlag object from true to false
|
|
or vice versa will be used only after switch restart.
|
|
|
|
As the auto save of configurations cannot be used when the
|
|
issConfigIncrSaveFlag is set to false, the issConfigAutoSaveTrigger
|
|
has to be set to false before setting the issConfigIncrSaveFlag
|
|
to false."
|
|
DEFVAL { false }
|
|
::= { issSystem 44 }
|
|
|
|
|
|
issConfigRollbackFlag OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
enabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates whether SNMP Rollback feature is enabled or disabled.
|
|
|
|
'enabled' value implies that failure in set operation for any varbind will result in rollback of all varbinds whose value has been set in this SET PDU
|
|
|
|
'disabled' value implies that failure in set operation will simply return error."
|
|
DEFVAL { enabled }
|
|
::= { issSystem 45 }
|
|
|
|
issConfigSyncUpOperation OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
syncup(1)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates that sync operation is to be performed.
|
|
Incremental save OFF: RB tree, incremental file/buffer are not present in
|
|
the system, sync operation is not allowed in the system.
|
|
Incremental save ON : On receiving this event, MSR deletes the data present
|
|
in the RB tree and configuration data at MSR shall be
|
|
made In sync with data store at protocols.
|
|
|
|
Following table explains the combinations of various configurations
|
|
============================================================================
|
|
issConfig issConfig
|
|
IncrSaveFlag SaveOption Behaviour
|
|
============================================================================
|
|
TRUE Remote Save RB Tree data made in sync with the data stored
|
|
at protocols, same data Is updated at remote
|
|
system, incremental file (at remote) is emptied.
|
|
|
|
TRUE Local Save RB Tree data made in sync with the data stored at
|
|
protocols, same data Is updated in local
|
|
configuration file and incremental file
|
|
(issinc.conf) is emptied.
|
|
|
|
FALSE xx Event is not allowed in the system,
|
|
MSR returns failure.
|
|
============================================================================"
|
|
|
|
DEFVAL { syncup }
|
|
::= { issSystem 46 }
|
|
|
|
issFrontPanelPortCount OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The object defines the number of physical ports configured
|
|
in a device for the purpose of switching/routing. The value
|
|
of the object should not exceed system defined MAX physical
|
|
interfaces, when the configured value is less than the MAX
|
|
physical interfaces, the difference in port count shall be
|
|
used for stacking purpose only when the stacking object
|
|
issColdStandbyStacking is enabled else the ports are considered
|
|
as physically not present and would not be initialized.
|
|
|
|
It is not advisable to change the Front panel port count when some
|
|
configurations are already saved.
|
|
|
|
Once the Front panel port count is configured, the switch has to
|
|
be restarted before saving any configuration."
|
|
|
|
::= { issSystem 47 }
|
|
|
|
issAuditLogStatus OBJECT-TYPE
|
|
SYNTAX INTEGER { enable (1) , disable(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "To Enable or disable Audit Logging"
|
|
DEFVAL { disable }
|
|
|
|
::= { issSystem 48 }
|
|
|
|
issAuditLogFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The name of the file to which Audit log is saved"
|
|
DEFVAL { "config.txt" }
|
|
|
|
::= { issSystem 49 }
|
|
|
|
issAuditLogFileSize OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1024 .. 1048576)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This is the maximum file size in bytes of the config.txt file"
|
|
DEFVAL { 1048576 }
|
|
|
|
::= { issSystem 50 }
|
|
issAuditLogReset OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "Setting this to true ,erases the contents in configs.txt
|
|
fileand start logging"
|
|
DEFVAL { false }
|
|
::= { issSystem 51 }
|
|
|
|
issAuditLogRemoteIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "IP Address of the remote system to which the
|
|
Audit file has to be transfered from flash.
|
|
This object is deprecated, as this object supports only
|
|
IPv4, this IP can be set through issAuditLogRemoteIpvxAddr object
|
|
and object issAuditLogRemoteAddrType will be set to 1 i.e. IPv4"
|
|
::= { issSystem 52 }
|
|
|
|
issAuditLogInitiateTransfer OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "Setting this will start transfer of the file indicated by
|
|
issAuditLogFileName from flash
|
|
to remote Address mentioned by issAuditLogRemoteIpAddr"
|
|
DEFVAL { false }
|
|
::= { issSystem 53 }
|
|
issAuditTransferFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The name of the file to be retrieved from flash"
|
|
DEFVAL { "config.txt" }
|
|
|
|
::= { issSystem 54 }
|
|
|
|
issDownLoadTransferMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tftp (1),
|
|
sftp (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"To select the Transfer mode for downloading image."
|
|
DEFVAL { tftp }
|
|
::= { issSystem 55 }
|
|
|
|
issDownLoadUserName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting User name required for downloading
|
|
image. When Transfer Mode is selected as tftp, contents of this
|
|
mib-object becomes irrelevant."
|
|
::= { issSystem 56 }
|
|
|
|
issDownLoadPassword OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting password required for downloading
|
|
image. When Transfer Mode is selected as tftp, contents of this
|
|
mib-object becomes irrelevant."
|
|
::= { issSystem 57 }
|
|
|
|
issUploadLogTransferMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tftp (1),
|
|
sftp (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"To select the Transfer mode for uploading log file."
|
|
DEFVAL { tftp }
|
|
::= { issSystem 58 }
|
|
|
|
|
|
issUploadLogUserName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting User name required for uploading
|
|
log file. When Transfer Mode is selected as tftp, contents of this
|
|
mib-object becomes irrelevant."
|
|
::= { issSystem 59 }
|
|
|
|
issUploadLogPasswd OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting password required for uploading log file.
|
|
When Transfer Mode is selected as tftp, contents of this mib-object becomes
|
|
irrelevant."
|
|
::= { issSystem 60 }
|
|
|
|
issConfigSaveTransferMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tftp (1),
|
|
sftp (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"To select the Transfer mode for saving the configurations on to a
|
|
remote system. Contents of this mib is relevant only when
|
|
issConfigSaveOption is remote save."
|
|
DEFVAL { tftp }
|
|
::= { issSystem 61 }
|
|
|
|
issConfigSaveUserName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting User name required for saving
|
|
configurations onto a remote site. Contents of this mib is relevant only
|
|
when issConfigSaveOption is remote save and issConfigSaveTransferMode is
|
|
SFTP."
|
|
::= { issSystem 62 }
|
|
|
|
issConfigSavePassword OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..20))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This mib-object is used for setting Password required for saving
|
|
configurations onto a remote site. Contents of this mib is relevant
|
|
only when the value of issConfigSaveOption is remote save and
|
|
issConfigSaveTransferMode is SFTP."
|
|
::= { issSystem 63 }
|
|
|
|
issSwitchMinThresholdTemperature OBJECT-TYPE
|
|
SYNTAX Integer32 (-15..30)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the minimum threshold temperature of the switch in celsius.
|
|
When the current temperature drops below the threshold,
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 10 }
|
|
::= { issSystem 64 }
|
|
|
|
issSwitchMaxThresholdTemperature OBJECT-TYPE
|
|
SYNTAX Integer32 (35..40)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the maximum threshold temperature of the switch in celsius.
|
|
When the current temperature rises above the threshold,
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 40 }
|
|
::= { issSystem 65 }
|
|
|
|
issSwitchCurrentTemperature OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current temperature of the switch in celsius."
|
|
|
|
::= { issSystem 66 }
|
|
|
|
issSwitchMaxCPUThreshold OBJECT-TYPE
|
|
SYNTAX Integer32 (1..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the maximum CPU usage of the switch in percentage.
|
|
When CPU load exceeds the threshold value,
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 95 }
|
|
::= { issSystem 67 }
|
|
|
|
issSwitchCurrentCPUThreshold OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current CPU threshold of the switch in percentage"
|
|
|
|
::= { issSystem 68 }
|
|
|
|
issSwitchPowerSurge OBJECT-TYPE
|
|
SYNTAX Integer32 (1..255)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the maximum power supply of the switch in volts.
|
|
When the current voltage exceeds the threshold value,
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 230 }
|
|
::= { issSystem 69 }
|
|
|
|
issSwitchPowerFailure OBJECT-TYPE
|
|
SYNTAX Integer32 (1..255)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the minimum power supply of the switch in volts.
|
|
When the current voltage drops below the threshold value,
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 100 }
|
|
::= { issSystem 70 }
|
|
|
|
issSwitchCurrentPowerSupply OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current power supply in volts."
|
|
|
|
::= { issSystem 71 }
|
|
|
|
issSwitchMaxRAMUsage OBJECT-TYPE
|
|
SYNTAX Integer32 (1..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the maximum RAM usage of the switch in percentage.
|
|
When the RAM usage crosses the threshold percentage
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 90 }
|
|
::= { issSystem 72 }
|
|
|
|
issSwitchCurrentRAMUsage OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current RAM usage of the switch in percentage"
|
|
|
|
::= { issSystem 73 }
|
|
|
|
issSwitchMaxFlashUsage OBJECT-TYPE
|
|
SYNTAX Integer32 (1..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the maximum flash usage of the switch in percentage.
|
|
When the flash usage crosses the threshold percentage
|
|
an SNMP trap with maximum severity will be sent to the manager."
|
|
|
|
DEFVAL { 95 }
|
|
::= { issSystem 74 }
|
|
|
|
issSwitchCurrentFlashUsage OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current flash usage of the switch in percentage"
|
|
|
|
::= { issSystem 75 }
|
|
|
|
|
|
issConfigRestoreFileFormatVersion OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..12))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Config Save Restoration file format Version.This issConfigRestoreFile
|
|
FormatVersion value will be compared in each reboot against file format
|
|
version value stored in restoration file.Restoration will occur only if
|
|
the Restore file format version OID in restoration file matches this
|
|
OID and the value of Restore file format version field in restoration
|
|
file matches this OID's value.
|
|
|
|
The current value of this issConfigRestoreFileFormatVersion is 1.1.
|
|
If any change happens in Restore File Format,then the value of this object
|
|
will be updated like this 1.2,1.3,1.4,1.5,...."
|
|
|
|
::= { issSystem 76 }
|
|
|
|
issDebugOption OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..288))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object stores the trace option string input given by the user.
|
|
To enable particular trace the user has to enter
|
|
the corresponding string(given below) assigned for that.
|
|
And for enabling more than once traces the user has to enter the
|
|
corresponding strings with SPACE delimiter between each string.
|
|
enable - Enables the corresponding option.
|
|
disable - Disables the corresponding option.
|
|
init-shut - Init and Shutdown traces
|
|
failure - All Failure Traces
|
|
func-entry-exit - Funtion entry and exit
|
|
for example to enable init-shut and failure trace the input string
|
|
should be enable init-shut failure"
|
|
::= { issSystem 77 }
|
|
|
|
issConfigDefaultValueSaveOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates whether default values needs to be saved or not when
|
|
incremental save option is true.'enabled' value implies, MSR stores
|
|
default values also when Incremental save is true.'disabled' value
|
|
implies, MSR does not store default values when Incremental save is
|
|
true.
|
|
|
|
Configuring this object value will update in issnvram.txt file.
|
|
The configured value will get into effect only after rebooting the ISS."
|
|
|
|
DEFVAL { disabled }
|
|
|
|
::= { issSystem 78 }
|
|
|
|
issConfigSaveIpAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the address type of the remote system to which
|
|
the switch configurations have to be saved.The address type can be
|
|
IPv4 or IPv6 unicast address or DNS.
|
|
|
|
This object is valid only if 'issConfigSaveOption' is chosen to be
|
|
'remoteSave'."
|
|
::= { issSystem 79 }
|
|
|
|
issConfigSaveIpvxAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IP Address of the remote system to which the switch
|
|
configurations have to be saved. It supports DNS host name
|
|
when 'issConfigSaveIpAddrType' is of DNS Type.
|
|
|
|
This object is valid only if 'issConfigSaveOption' is chosen to be
|
|
'remoteSave'."
|
|
::= { issSystem 80 }
|
|
|
|
issConfigRestoreIpAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IP Address type of the remote system from where
|
|
the switch configurations have to be downloaded to the
|
|
'Startup Configuration File' in the flash.
|
|
The address type can be IPv4 or IPv6 unicast address or DNS."
|
|
::= { issSystem 81 }
|
|
|
|
issConfigRestoreIpvxAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the IP Address of the remote system from where
|
|
the switch configurations have to be downloaded to the
|
|
'Startup Configuration File' in the flash.
|
|
The address type can be IPv4 or IPv6 unicast address or DNS type."
|
|
::= { issSystem 82 }
|
|
|
|
issDlImageFromIpAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the address type of machine from where the image
|
|
has to be downloaded. The address type can be IPv4 or IPv6
|
|
unicast address or DNS."
|
|
::= { issSystem 83 }
|
|
|
|
issDlImageFromIpvx OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The IP Address of machine from where the image has to be downloaded."
|
|
::= { issSystem 84 }
|
|
|
|
issUploadLogFileToIpAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the address Type of machine to which the log file is
|
|
to be uploaded.The address type can be IPv4 or IPv6 unicast address or DNS."
|
|
::= { issSystem 85 }
|
|
|
|
issUploadLogFileToIpvx OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the address type of machine to which the log file is to be uploaded."
|
|
::= { issSystem 86 }
|
|
|
|
issAuditLogRemoteIpAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "IP Address Type of the remote system to which the
|
|
Audit file has to be transfered from flash."
|
|
::= { issSystem 87 }
|
|
|
|
issAuditLogRemoteIpvxAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "IP Address of the remote system to which the
|
|
Audit file has to be transfered from flash."
|
|
::= { issSystem 88 }
|
|
|
|
-- Set System Timer speed configuration
|
|
|
|
issSystemTimerSpeed OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..1000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "Configures the system timer speed. This is for testing purpose.
|
|
Value - 1 enables the timer to run in real time speed.
|
|
Values from (2 - 1000), enables the timer to run
|
|
(2x - 1000x) faster."
|
|
::= { issSystem 89 }
|
|
|
|
issMgmtInterfaceRouting OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
" Enables / Disables Routing over the Management Interface.
|
|
|
|
This object can be configured only if the Management Port
|
|
is used for IP Access. "
|
|
|
|
DEFVAL { disabled }
|
|
|
|
::= { issSystem 90 }
|
|
|
|
issMacLearnRateLimit OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Maximum number of unicast dynamic MAC (L2) entries hardware can learn
|
|
in the system, in a configured time interval 'issMacLearnRateLimitInterval'.
|
|
In next subsequent time interval, hardware can learn number of previously
|
|
learnt MAC entries plus present 'issMacLearnRateLimit' value, this
|
|
cycle will continue until MAC learning reaches to maximum number of L2
|
|
unicast dynamic entries learning capacity of the system. If rate limit is
|
|
changed while 'issMacLearnLimitRateInterval' timer is running, new rate
|
|
limit value takes effect on next timer restart.
|
|
|
|
This limit is to control the number of MAC entries indication to control
|
|
plane from hardware, when hardware MAC learning is enabled.
|
|
|
|
Configuration value '0' disables this feature in the system.
|
|
This configuration does not impose any restrictions on multicast/broadcast
|
|
and dynamic/static/protocol(MMRP) MAC learning capability limits."
|
|
DEFVAL { 1000 }
|
|
::= { issSystem 91 }
|
|
|
|
issMacLearnRateLimitInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..100000)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of MAC entries,'issMacLearnRateLimit' that can be learnt in
|
|
the system in this configured time interval. Any changed timer interval
|
|
value will take effect in next timer restart."
|
|
DEFVAL { 1000 }
|
|
::= { issSystem 92 }
|
|
|
|
issVrfUnqMacFlag OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disable (0),
|
|
enable (1)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Unique mac address can be assigned to each virtual router by enabling
|
|
this flag. Configuring this object value will result in updation to
|
|
issnvram.file. The configured value will take effect in ISS on next reboot."
|
|
|
|
DEFVAL { disable }
|
|
::= {issSystem 93}
|
|
|
|
issLoginAttempts OBJECT-TYPE
|
|
SYNTAX Integer32(1..10)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of times a user may be allowed to login using
|
|
wrong password in the login prompt."
|
|
DEFVAL {3}
|
|
::= {issSystem 94}
|
|
|
|
issLoginLockTime OBJECT-TYPE
|
|
SYNTAX Integer32(30..900)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Time in seconds a user is blocked following unsuccessful logins."
|
|
DEFVAL {600}
|
|
::= {issSystem 95}
|
|
|
|
issAuditLogSizeThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..99)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the threshold value of the Log storage space with respect
|
|
to the maximum Log Storage Space. It is entered as a percentage value."
|
|
DEFVAL { 70 }
|
|
::= { issSystem 96}
|
|
|
|
|
|
issTelnetStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2),
|
|
enableInProgress(3),
|
|
disableInProgress(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for enabling or disabling the TELNET in the system.
|
|
Set operation of enable will move this object to the enableInProgress
|
|
first then to the enable on successfull transition. Otherwise it will
|
|
move back to the old state. Same applies to the disable also.
|
|
|
|
CAUTION: enableInProgress and disableInProgress are not admin
|
|
configurable values"
|
|
DEFVAL { enable }
|
|
::= { issSystem 97 }
|
|
|
|
issWebSessionTimeOut OBJECT-TYPE
|
|
SYNTAX Integer32 (1..300)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set the Web Session Time Out Value in Seconds"
|
|
DEFVAL { 300 }
|
|
::= { issSystem 98 }
|
|
|
|
issWebSessionMaxUsers OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set the maximum number of web sessions"
|
|
DEFVAL { 7 }
|
|
::= { issSystem 99 }
|
|
|
|
issHeartBeatMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
internal (1),
|
|
external (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The object is for setting the method for Redundancy manager election
|
|
mechanism, it can be internal election logic or it can be a external
|
|
logic. When this object is set to be internal, proprietary
|
|
election logic called as HearBeat mechanism is applied for electing the
|
|
Active/Standby card in a redundant systems. When this object is set
|
|
to be external, external election logic should be applied for electing
|
|
Active/Standby card in a redundant systems.
|
|
|
|
By default this object is set to Internal."
|
|
DEFVAL { internal }
|
|
::= {issSystem 100}
|
|
|
|
issRmRType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
hot (1),
|
|
cold(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The object is for setting the type of the Redundancy manager, it can be
|
|
Hot or Cold. When this object is set to be cold, whenever there is node
|
|
state transition from Standby to Active, the node needs to re-start,
|
|
re-initialized the hardware completely. When this object is set to be
|
|
Hot, whenever there is node state transition from Standby to Active,
|
|
the hardware should not be re-initialized. When the configurations are
|
|
saved in a file in Active node, then this needs to be transferred to
|
|
the standby node in both the redundancy modes.
|
|
|
|
By default this is set to Hot."
|
|
DEFVAL { hot }
|
|
::= {issSystem 101}
|
|
|
|
issRmDType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
shared (1),
|
|
separate (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the type of the dataplane/hardware, it can be a
|
|
shared dataplane or a separate dataplane. When this object is set to
|
|
be shared, standby card in a redundancy system should not program the
|
|
hardware and hardware audit should be conducted to sync the hardware
|
|
and software after switchover/node-transition. When this object is set
|
|
to be separate, it specifies that the nodes have separate hardware,
|
|
therefore standby card in a redundant system should program the
|
|
hardware and hardware audit is not required, since the hardware and
|
|
software are in sync always.
|
|
|
|
By default this is set to Shared."
|
|
DEFVAL { shared }
|
|
::= {issSystem 102}
|
|
|
|
issClearConfig OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When the object is set to TRUE, configurations will be cleared and
|
|
default configurations will be restored. The value will be reset to
|
|
FALSE again."
|
|
|
|
DEFVAL { false }
|
|
::= { issSystem 103 }
|
|
|
|
issClearConfigFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the name of the file, which contains the default configurations
|
|
to be restored once configurations are cleared. This is optional. When
|
|
this file name is given, configurations in this file are assumed to be
|
|
default configurations. This configuration will be restored once the
|
|
configurations are cleared in ISS data base. When this file name is not
|
|
given, default configurations will not be restored. Only default
|
|
interface and VLAN will be brought up for management connectivity.
|
|
|
|
When default configurations are to be restored, this object should be
|
|
configured first before configuring the issClearConfig object."
|
|
|
|
DEFVAL { "clear.conf" }
|
|
::= { issSystem 104 }
|
|
|
|
issTelnetClientStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(0),
|
|
enabled(1)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for enabling or disabling the TELNET client functionality
|
|
in the system. Set operation of enable will allow to establish new Telnet
|
|
client sessions. Set operation of disable will not allow a new Telnet client
|
|
session, also terminates the active client sessions which are already running.
|
|
By default it will be enabled"
|
|
|
|
DEFVAL { enabled }
|
|
::= { issSystem 105 }
|
|
|
|
issSshClientStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(0),
|
|
enabled(1)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for enabling or disabling the SSH client functionality
|
|
in the system. Set operation of enable will allow to establish new SSH client
|
|
sessions. Set operation of disable will not allow a new SSH client sessions,
|
|
also terminates the active client sessions which are already running.
|
|
By default it will be enabled"
|
|
DEFVAL { enabled }
|
|
::= { issSystem 106 }
|
|
|
|
issActiveTelnetClientSessions OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the number of active Telnet client sessions running"
|
|
::= { issSystem 107 }
|
|
|
|
issActiveSshClientSessions OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the number of active SSH client sessions running"
|
|
::= { issSystem 108 }
|
|
|
|
issLogFileSize OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This is the maximum file size in bytes of the log file"
|
|
DEFVAL { 1048576 }
|
|
|
|
::= { issSystem 109 }
|
|
|
|
issLogReset OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "Setting this to true ,erases the contents in configs.txt
|
|
fileand start logging"
|
|
DEFVAL { false }
|
|
::= { issSystem 110 }
|
|
|
|
issLogSizeThreshold OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..99)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the threshold value of the Log storage space with respect
|
|
to the maximum Log Storage Space. It is entered as a percentage value."
|
|
DEFVAL { 70 }
|
|
::= { issSystem 111 }
|
|
|
|
issAutomaticPortCreate OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
}
|
|
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for enabling and disabling automatic
|
|
port create feature.When set to enabled the ports in
|
|
will be automatically created in RSTP module when it
|
|
is mapped to a context.When set to disabled ports
|
|
are not created automatically and ports can be created
|
|
at rstp module level. "
|
|
DEFVAL { enabled }
|
|
::= { issSystem 112 }
|
|
|
|
issUlRemoteLogFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to specify the filename/filename with path
|
|
to which the local file need to be copied in the remote system.
|
|
|
|
This object is useful only when the 'LogOption' is chosen as 'file'."
|
|
DEFVAL { "iss.log" }
|
|
::= { issSystem 113 }
|
|
|
|
|
|
issDefaultExecTimeOut OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is for configuring the default idle time out for
|
|
ISS Prompt (exec-time out)."
|
|
::= { issSystem 114 }
|
|
|
|
issRmStackingInterfaceType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
oob (1),
|
|
inband (2)
|
|
}
|
|
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
" This object is used to specify the type of stacking Interface used for
|
|
RM communication . Interface can be either an Out of Band port (or)
|
|
an Inband Ethernet port. This will be specified in issnvram.txt.
|
|
|
|
If an Out of Band port is used,RM Interface should be specified in
|
|
issnvram.txt . RM Heartbeat and synchronization messages will be
|
|
transmitted as IP packets. Native Linux TCP/IP stack is used to
|
|
achieve Transport protocol functionality.
|
|
|
|
If an Inband Ethernet port is used, RM Stack Interface will be
|
|
specified in Nodeid file . RM Heartbeat messages will be transmitted
|
|
as Ethernet packets and synchronization messages will be transmitted
|
|
as IP packets .Aricent TCP/IP stack is used to achieve Transport
|
|
protocol functionality.IP Address and the subnet Mask to be used for
|
|
this TCP/IP communication will be specified in NodeId file.
|
|
|
|
Configuring this object will result in updation to issnvram.txt file.
|
|
The configured value will take effect in ISS on next reboot."
|
|
|
|
DEFVAL { oob }
|
|
::= { issSystem 115 }
|
|
|
|
|
|
issPeerLoggingOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
console(1),
|
|
file(2),
|
|
flash(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Logging option specifying whether the Standby logging is to be
|
|
done at console or to a file(system buffer) in the system.
|
|
Flash specifies the logging of traces into a file."
|
|
DEFVAL { console }
|
|
::= { issSystem 116 }
|
|
|
|
issStandbyRestart OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
" In a High Availability System, this object allows the user to restart the
|
|
Standby switch (i.e) the entire Standby switch will operationally go down and
|
|
start again.
|
|
|
|
Setting a value of 'true' causes the Standby switch to be restarted. This
|
|
configuration will be done in the Active switch in order to restart the
|
|
Standby switch.
|
|
|
|
This configuration will not have any impact on the Active switch.
|
|
Active switch can be restarted using issRestart object."
|
|
|
|
DEFVAL { false }
|
|
::= { issSystem 117 }
|
|
|
|
issRestoreType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
msr (1),
|
|
csr (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
|
|
"Specifies whether the restoration type is MIB based save and restore
|
|
or CLI based save and restore.
|
|
|
|
The value 'msr' specifies that the configuration restore will be
|
|
in the format of MIB OID.
|
|
|
|
The value 'csr' specifies that the configuration restore will be
|
|
in the format of CLI commands"
|
|
|
|
|
|
DEFVAL { msr }
|
|
::= { issSystem 118 }
|
|
|
|
issSwitchModeType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
cutThroughSameSpeed (1),
|
|
storeForward (2),
|
|
cutThroughSlowToFast (3),
|
|
cutThroughFastToSlow (4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This MIB object configures switching mode configuration at
|
|
switch level. The switching mode configuration done at switch
|
|
level will be applied on all the ports in the system including
|
|
stacking ports.
|
|
|
|
When configured as StoreForward(2), the switch operates in a
|
|
store-and-forward mode and the switch checks each frame for
|
|
cyclic redundancy check (CRC) errors before forwarding them
|
|
to the network. Each frame is stored until the entire frame
|
|
has been received and checked. Because the switch waits for
|
|
forwarding the frame until the entire frame has been received
|
|
and checked, the switching speed in Store-Forward switching
|
|
mode is slower than the switching speed in Cut-Through
|
|
switching modes.
|
|
|
|
When configured any of the cut-through modes, the switch
|
|
operates in Cut-Through switching mode and start forwarding
|
|
the frame as soon as the switch has read the destination
|
|
details in the packet header. A switch in Cut-Through mode
|
|
forwards the data before it has completedreceiving the entire
|
|
frame. The switching speed in Cut-Through mode is faster than
|
|
the switching speed in Store-Forward switching mode.
|
|
|
|
Switching mode configuration:
|
|
CutThroughSameSpeed(1) : Cut-through forwarding between same speed
|
|
ports
|
|
StoreForward(2) : Store and forward switching mode
|
|
CutThroughSlowToFast(3): Cut-through forwarding between slower to
|
|
faster speed ports.
|
|
CutThroughFastToSlow(4): Cut-through forwarding between faster to
|
|
slower speed ports.
|
|
NOTE:
|
|
Few platforms supports extended Cut-Through mode for ports with
|
|
mismatched speeds.(eg. slow-to-fast, fast-to-slow).
|
|
Platforms which doesn't support extended Cut-Through mode,
|
|
Cut-Through same speed shall be considered as Cut-Through
|
|
switching mode"
|
|
DEFVAL { storeForward }
|
|
::={ issSystem 119 }
|
|
|
|
issConfigRestoreRetries OBJECT-TYPE
|
|
SYNTAX Integer32 (1..10)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used for configuring the number of retry attempts
|
|
for establishing connection with server during remote restore
|
|
operation"
|
|
DEFVAL { 1 }
|
|
::= { issSystem 120 }
|
|
|
|
issPauseFloodSamplingInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32 (10..300)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to set the sampling interval rate in seconds for pause
|
|
flood detection and protection feature."
|
|
DEFVAL { 30 }
|
|
::= { issSystem 121 }
|
|
|
|
issPauseFloodProtect OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This Object is used to Enable or disable the pause flood detection and
|
|
protection feature on all the ports in the system. Enabling this feature
|
|
avoids the resource exhaustion condition caused by pause frames/priority-based
|
|
pause frames.
|
|
The pause flood detection and protection feature is disabled by default."
|
|
DEFVAL { disabled }
|
|
::= { issSystem 122 }
|
|
|
|
issPauseFloodMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled (1),
|
|
detectionOnly (2),
|
|
enabled (3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This Object specifies the pause flood mode as disabled/detected-only/enabled
|
|
for all the ports in the system.
|
|
|
|
'disabled' - In this mode, system is not monitored for pause flood
|
|
condition.
|
|
|
|
'detectionOnly' - In this mode, all system ports are monitored for pause
|
|
flood condition. All the system ports pause flood status
|
|
and statistics counters are updated. No protection action
|
|
is taken and no SNMP trap are generated. All the ports
|
|
in the system are allowed to operate normally and the
|
|
pause flood status is continually monitored and updated.
|
|
|
|
'enabled' - In this mode, all system ports are monitored for pause
|
|
flood condition. When pause flood condition is detected,
|
|
protective action is taken by disabling the administrator
|
|
status of those ports. The pause flood of those ports status
|
|
will be updated to indicate the existence of such condition.
|
|
Ports for which protective action is taken are remains in
|
|
disabled state until an administrative action is taken."
|
|
DEFVAL { disabled }
|
|
::= { issSystem 123 }
|
|
|
|
issPauseFloodReset OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to recover or re-eanble the pause-flood
|
|
detection-only/enabled condition.
|
|
|
|
Recovery action in Detection-only mode has to log every sampling and clear
|
|
the status and stats.
|
|
|
|
Recovery action in enabled mode has to re-enable the ports
|
|
that were disabled due to the pause flood protective action."
|
|
DEFVAL { false }
|
|
::= { issSystem 124 }
|
|
|
|
issPauseFloodTraceSeverityLevel OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
emergency (0),
|
|
alert (1),
|
|
critical (2),
|
|
error (3),
|
|
warning (4),
|
|
notice (5),
|
|
informational (6),
|
|
debug (7)
|
|
}
|
|
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the value of severity level been configured for pause flood
|
|
module's debug tracing. It uses the value 0 (emergency) to 7 (debug). The value 0 is
|
|
given to higher priority trace messages and 7 given to lower priority traces messages.
|
|
The trace messages defined at or numerically lower than the value configured in
|
|
this MIB object are logged."
|
|
DEFVAL { 4 }
|
|
::= { issSystem 125 }
|
|
|
|
issPauseFloodTraceOption OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to store the debug trace types that are enable by the user
|
|
for all the interfaces in the system. The bit positions of the traces is shown below.
|
|
Bit 0 - no trace
|
|
Bit 1 - init-shut
|
|
Bit 2 - mgmt
|
|
Bit 3 - sampling
|
|
Bit 4 - os resource
|
|
Bit 5 - entry
|
|
Bit 6 - exit "
|
|
DEFVAL { 0 }
|
|
::= { issSystem 126 }
|
|
|
|
issPortsSwitchingModeStatus OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to reflect the switching mode
|
|
configuration of each physical port in the hardware.
|
|
|
|
The switching mode is updated as bit-wise representation.
|
|
|
|
Each bit position represents the interface index.
|
|
That is bit position 0 is for IfIndex 1,
|
|
bit position 1 is for IfIndex 2 and so on.
|
|
|
|
The bit value represents the switching mode.
|
|
That is bit value 1 represent Cut-Through and
|
|
bit value 0 represent Store-Forward."
|
|
::= { issSystem 127 }
|
|
|
|
issDebugTimeStampOption OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to set the time stamp value in debug trace.
|
|
When time stamp is ENABLED, debug traces will be printed with timestamp and
|
|
when it is DISABLED, time stamp will not be displayed with the traces"
|
|
|
|
DEFVAL { disabled }
|
|
|
|
::= { issSystem 128 }
|
|
|
|
issLdapLoginPrivilege OBJECT-TYPE
|
|
SYNTAX INTEGER
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This object specifies the default privilege for users authenticated using LDAP."
|
|
|
|
DEFVAL { 0 }
|
|
::= { issSystem 129 }
|
|
|
|
issLdapAttributeName OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This object specifies the attribute name of the field to be authenticated using LDAP."
|
|
|
|
DEFVAL { "" }
|
|
::= { issSystem 130 }
|
|
|
|
issConfigRestoreFileSkuManifest OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "This object specifies the switch models againts which the config file can be used for restoring configuration
|
|
String contains supported model numbers separated by ; (e.g. 1;2;3;4)"
|
|
|
|
DEFVAL { "" }
|
|
::= { issSystem 131 }
|
|
|
|
issDlImageType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
agent(1),
|
|
diagnostic(2),
|
|
firmware-cpld(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This object specifies the image type which will be downloaded"
|
|
|
|
DEFVAL { 1 }
|
|
::= { issSystem 132 }
|
|
|
|
issFirmwareCpldVersion OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "This object specifies the cpld firmware version on the switch"
|
|
|
|
DEFVAL { "" }
|
|
::= { issSystem 133 }
|
|
|
|
issHttpMaxSessions OBJECT-TYPE
|
|
SYNTAX Integer32 (1..10)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to set HTTP max sessions.
|
|
If the max sessions is being reduced, http(s) system is disabled,
|
|
are closed all the sessions and enabled again."
|
|
DEFVAL { 10 }
|
|
::= { issSystem 134 }
|
|
|
|
------ Config Control Group ------------------------------------
|
|
|
|
issConfigCtrlTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssConfigCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to control device features like egress traffic control,
|
|
stats collection, etc. either for the entire switch or for each
|
|
interface in the switch."
|
|
::= { issConfigControl 1 }
|
|
|
|
issConfigCtrlEntry OBJECT-TYPE
|
|
SYNTAX IssConfigCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each interface in the system.
|
|
|
|
In addition to that an entry with index '0' is created in this
|
|
table by default.
|
|
|
|
If 'issConfigCtrlStatus' of the entry '0' is made 'valid', then
|
|
global control is chosen and the values against entry '0' is
|
|
applicable for all the interfaces of the switch.
|
|
|
|
If 'issConfigCtrlStatus' of the entry '0' is made 'invalid',
|
|
then interface-wise control is chosen & the values against each
|
|
interface index is applicable for that interface.
|
|
|
|
At a particular point of time, either global control will be
|
|
applicable or interface-wise control is applicable.
|
|
Both will not be considered together.
|
|
|
|
Index to the table is the interface index of the port."
|
|
|
|
INDEX { issConfigCtrlIndex }
|
|
::= { issConfigCtrlTable 1 }
|
|
|
|
IssConfigCtrlEntry ::=
|
|
SEQUENCE {
|
|
issConfigCtrlIndex
|
|
Integer32,
|
|
issConfigCtrlEgressStatus
|
|
INTEGER,
|
|
issConfigCtrlStatsCollection
|
|
INTEGER,
|
|
issConfigCtrlStatus
|
|
INTEGER
|
|
}
|
|
|
|
issConfigCtrlIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Interface index of the port for which the configuration
|
|
in this entry applies.
|
|
|
|
If any configuration is made in this table for the index '0',
|
|
that configuration will be considered as global configuration
|
|
and is applicable for all the interfaces of the switch."
|
|
::= { issConfigCtrlEntry 1 }
|
|
|
|
issConfigCtrlEgressStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls the transmission of egress traffic over this interface.
|
|
|
|
This value for entry '0' controls the egress traffic over all
|
|
interfaces."
|
|
DEFVAL { enabled }
|
|
::= { issConfigCtrlEntry 2 }
|
|
|
|
|
|
issConfigCtrlStatsCollection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Enables or disables statistics collection for this interface.
|
|
|
|
This value for entry '0' controls the stats collection for all
|
|
interfaces."
|
|
DEFVAL { enabled }
|
|
::= { issConfigCtrlEntry 3 }
|
|
|
|
issConfigCtrlStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
valid (1),
|
|
invalid (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Speficies the validity of the entry.
|
|
|
|
If the 'Config Control Status' for entry '0' is made 'valid',
|
|
then global control is chosen in the system.
|
|
It signifies that the values against entry '0' is applicable
|
|
for all the interfaces of the switch.
|
|
|
|
If the 'Config Control Status' for entry '0' is made 'invalid',
|
|
then interface-wise control is chosen.
|
|
Then the values against each interface index is applicable
|
|
for that interface.
|
|
|
|
By default, 'issConfigCtrlStatus' will be 'invalid' for
|
|
entry '0' and 'valid' for all other entries.
|
|
(ie) by default, interface-wise configuration is enabled
|
|
in the system.
|
|
|
|
The status of entries other than the zeroth(0th) entry can not be
|
|
made 'invalid'."
|
|
::= { issConfigCtrlEntry 4 }
|
|
|
|
|
|
-- Port Control Table
|
|
|
|
issPortCtrlTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssPortCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to control the port specific parameters of the device like speed,
|
|
duplex mode, etc."
|
|
::= { issConfigControl 2 }
|
|
|
|
issPortCtrlEntry OBJECT-TYPE
|
|
SYNTAX IssPortCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each interface in the system.
|
|
|
|
Index to the table is the interface index of the port."
|
|
|
|
INDEX { issPortCtrlIndex }
|
|
::= { issPortCtrlTable 1 }
|
|
|
|
IssPortCtrlEntry ::=
|
|
SEQUENCE {
|
|
issPortCtrlIndex
|
|
Integer32,
|
|
issPortCtrlMode
|
|
INTEGER,
|
|
issPortCtrlDuplex
|
|
INTEGER,
|
|
issPortCtrlSpeed
|
|
INTEGER,
|
|
issPortCtrlFlowControl
|
|
INTEGER,
|
|
issPortCtrlRenegotiate
|
|
INTEGER,
|
|
issPortCtrlMaxMacAddr
|
|
Integer32,
|
|
issPortCtrlMaxMacAction
|
|
INTEGER,
|
|
issPortHOLBlockPrevention
|
|
INTEGER,
|
|
issPortAutoNegAdvtCapBits
|
|
OCTET STRING,
|
|
issPortCpuControlledLearning
|
|
INTEGER,
|
|
issPortMdiOrMdixCap
|
|
INTEGER,
|
|
issPortCtrlFlowControlMaxRate
|
|
Integer32,
|
|
issPortCtrlFlowControlMinRate
|
|
Integer32,
|
|
issPortCtrlPauseFloodProtect
|
|
INTEGER,
|
|
issPortCtrlPauseFloodMode
|
|
INTEGER,
|
|
issPortCtrlPauseFloodStatus
|
|
INTEGER,
|
|
issPortCtrlPauseFloodReset
|
|
TruthValue,
|
|
issPortCtrlPauseFloodStats
|
|
Unsigned32,
|
|
issPortCtrlPauseFloodStatsClear
|
|
TruthValue,
|
|
issPortCtrlPauseFloodTraceOption
|
|
Integer32,
|
|
issPortCtrlSwitchModeType
|
|
INTEGER,
|
|
issPortCtrlSwitchModeStatus
|
|
INTEGER,
|
|
issPortCtrlInbandAutoNeg
|
|
INTEGER,
|
|
issPortCtrlBypassInbandAutoNeg
|
|
INTEGER,
|
|
issPortCtrlForceSpeed
|
|
INTEGER
|
|
}
|
|
|
|
issPortCtrlIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Interface index of the port for which the configuration
|
|
in this entry applies."
|
|
|
|
::= { issPortCtrlEntry 1 }
|
|
|
|
issPortCtrlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
auto (1),
|
|
noNegotiation (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Speficies the mode in which the speed, duplex modes and flow control
|
|
of the interface is determined.
|
|
|
|
If set as 'auto', the hardware senses speed and negotiates with the port
|
|
on the other end of the link for data transfer operation as
|
|
'full-duplex' or 'half-duplex' and about flow contol.
|
|
|
|
If set as 'nonegotiation', the configured values for interface
|
|
speed, duplex mode and flow control will be effective."
|
|
|
|
DEFVAL { auto }
|
|
::= { issPortCtrlEntry 2 }
|
|
|
|
issPortCtrlDuplex OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
full (1),
|
|
half (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configures interface data transfer mode as full-duplex or half-duplex.
|
|
|
|
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
|
|
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
|
|
after negotiating with its peer"
|
|
|
|
::= { issPortCtrlEntry 3 }
|
|
|
|
issPortCtrlSpeed OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tenMBPS (1),
|
|
hundredMBPS (2),
|
|
oneGB (3),
|
|
tenGB (4),
|
|
fortyGB (5),
|
|
fiftyGB (6),
|
|
twothousandfivehundredMBPS (7),
|
|
twentyfiveGB (8),
|
|
onehundredGB (9)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configures interface speed.
|
|
|
|
This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
|
|
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
|
|
after negotiating with its peer"
|
|
|
|
::= { issPortCtrlEntry 4 }
|
|
|
|
issPortCtrlFlowControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable (1),
|
|
disable (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Enables / disables flow control for the interface.
|
|
|
|
This object be configured only if the 'PortCtrlMode' is 'nonegotiation'.
|
|
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
|
|
after negotiating with its peer.
|
|
|
|
Since this object is deprecated, corresponding functionality can be
|
|
realised by dot3PauseAdminMode from stdether.mib"
|
|
|
|
::= { issPortCtrlEntry 5 }
|
|
|
|
issPortCtrlRenegotiate OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When configured as 'true', restarts autonegotiation on the interface.
|
|
|
|
Once autonegotiation is restarted, the value of this object reverts
|
|
to 'false'."
|
|
|
|
DEFVAL { false }
|
|
::= { issPortCtrlEntry 6 }
|
|
|
|
issPortCtrlMaxMacAddr OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the maximum number of new MAC addresses that can be
|
|
learnt over the interface."
|
|
::= { issPortCtrlEntry 7 }
|
|
|
|
issPortCtrlMaxMacAction OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
drop (1),
|
|
purgeLRU (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the action to be taken when the maximum number of new MAC
|
|
addresses that can be learnt over the interface is exceeded.
|
|
|
|
If the action is 'drop', the packet with new mac address will be
|
|
dropped once the maximum number of new MAC addresses that can be
|
|
learnt over the interface is exceeded.
|
|
|
|
If the action is 'purgeLRU', the 'Least Recently Used' mac address
|
|
will be deleted from the MAC table and the new mac address will be
|
|
added."
|
|
::= { issPortCtrlEntry 8 }
|
|
|
|
issPortHOLBlockPrevention OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled (1),
|
|
enabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Enables or disables Head-Of-Line Blocking prevention on a port."
|
|
DEFVAL { enabled }
|
|
::= { issPortCtrlEntry 9 }
|
|
issPortAutoNegAdvtCapBits OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A value uniquely identifies the set of capabilities advertised
|
|
by the local auto negotiation entity other than the standard
|
|
capabilities supported by ifMauAutoNegCapAdvertisedBits.
|
|
When this object is needed to be configured, one of the capabilities
|
|
from the standard object should be set to bOther."
|
|
::= { issPortCtrlEntry 10 }
|
|
|
|
issPortCpuControlledLearning OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled (1),
|
|
enabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Enables or disables the CPU controlled learning on a port.
|
|
The default behavior is hardware learning. By enabling this object
|
|
software learning on that particular port is enabled.
|
|
|
|
When CPU controlled learning is enabled, for the first time, packet
|
|
will be copied to CPU and source MAC address learning will not happen
|
|
in the hardware. When packet is received at PNAC - if the source MAC
|
|
address is authorized, the packet will be allowed to go through further
|
|
processing. Else, the packet will be dropped. When packets from
|
|
authorized MAC address are received at VLAN, MAC learning will happen
|
|
at VLAN and the same entry will be programmed in the hardware. Once the
|
|
MAC address is learnt, further forwarding will happen at driver itself.
|
|
|
|
The Mac address entries which are added through software learning are
|
|
checked in periodical intervals for the HIT entry. If there is no
|
|
traffic for that entry, the HIT flag won't be set. The entry will be
|
|
removed from the hardware if the hit flag is not set.
|
|
Note: When software learning is enabled, rate limiting to the port
|
|
needs to be configured"
|
|
|
|
DEFVAL { disabled }
|
|
::= { issPortCtrlEntry 11 }
|
|
|
|
issPortMdiOrMdixCap OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
auto (1),
|
|
mdi (2),
|
|
mdix (3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the port should be in Auto-Mdix mode or Mdi/Mdix.
|
|
|
|
Setting the value to `auto` enables the Auto MDIX in the port -
|
|
issPortCtrlIndex. This will be effective only when the speed of the
|
|
particular port is auto negotiable.
|
|
|
|
Setting the value to `mdi` disables the Auto MDIX in the port and the
|
|
port will be in mdi mode.
|
|
|
|
Setting the value to `mdix` disables the Auto MDIX in the port and the
|
|
port will be in mdix mode."
|
|
DEFVAL { auto }
|
|
::= { issPortCtrlEntry 12 }
|
|
|
|
issPortCtrlFlowControlMaxRate OBJECT-TYPE
|
|
SYNTAX Integer32 (0..80000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configures the maximum rate (kbps) - a high water mark beyond which
|
|
pause frames will be generated to flow control the ingress traffic.
|
|
This value should be set to 0 if no pause frame generation is required.
|
|
In chipsets that does not support seperate rate configuration for
|
|
pause frame generation, this object's value will take effect on
|
|
the interface ingress speed."
|
|
::= { issPortCtrlEntry 13 }
|
|
|
|
issPortCtrlFlowControlMinRate OBJECT-TYPE
|
|
SYNTAX Integer32 (0..80000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configures the minimum rate (kbps) - a low water mark below which pause
|
|
frames generation will be stopped. This value should be set to a value
|
|
lesser that of 'issPortCtrlFlowControlMaxRate'. This value should be set
|
|
to zero only when flow control is disabled. Chipsets on which this low
|
|
water mark is not supported, the 'issPortCtrlFlowControlMaxRate' will
|
|
alone be used."
|
|
::= { issPortCtrlEntry 14 }
|
|
|
|
issPortCtrlPauseFloodProtect OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled (1),
|
|
disabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable or disable the pause flood detection-only
|
|
or detection and protection feature on a port. The default behavior is
|
|
to have this feature disabled on a port. Enabling the feature avoid
|
|
resource exhaustion condition caused by pause frames/priority-based
|
|
pause frames"
|
|
DEFVAL { disabled }
|
|
::= { issPortCtrlEntry 15 }
|
|
|
|
issPortCtrlPauseFloodMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled (1),
|
|
detectionOnly (2),
|
|
enabled (3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the pause flood mode as disabled/detected-only/enabled
|
|
|
|
'disabled' - In this mode, port is not monitored for pause flood condition.
|
|
|
|
'detectionOnly' - In this mode, port is monitored for pause flood condition.
|
|
The port's pause flood status and statistics counters are updated. No protection
|
|
action is taken and no SNMP traps are generated. The port is allowed to
|
|
operate normally and the pause flood status is continually monitored and updated.
|
|
|
|
'enabled' - In this mode, port is monitored for pause flood condition.
|
|
When pause flood condition is detected, protective action is taken by disabling
|
|
the administrator status of the port. The pause flood port status will be
|
|
updated to indicate the existence of such a condition. The port remains in
|
|
disabled state until an administrative action is taken."
|
|
DEFVAL { disabled }
|
|
::= { issPortCtrlEntry 16 }
|
|
|
|
issPortCtrlPauseFloodStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
normal (1),
|
|
detected (2),
|
|
blocked (3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the pause flood status.
|
|
|
|
'normal' - This status specifies that the pause flood condition has not
|
|
been detected or the feature is disabled.
|
|
|
|
'detected' - This status specifies that the pause flood condition being
|
|
detected. This is applicable only when the pause flood mode
|
|
is 'detection-only'.
|
|
|
|
'blocked' - This status specifies the pause flood condition being detected
|
|
and protective action taken. This is applicable only when
|
|
the pause flood mode is 'enabled'"
|
|
::= { issPortCtrlEntry 17 }
|
|
|
|
issPortCtrlPauseFloodReset OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to recover or re-eanble the pause-flood
|
|
detection-only/enabled condition.
|
|
Recovery action in Detection-only mode has to log every sampling and clear
|
|
the status and stats.
|
|
|
|
Recovery action in enabled mode has to recovers/re-enables a port
|
|
that was disabled due to the pause flood protective action."
|
|
DEFVAL { false }
|
|
::= { issPortCtrlEntry 18 }
|
|
|
|
issPortCtrlPauseFloodStats OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to hold the number of times the port entered pause flood condition."
|
|
::= { issPortCtrlEntry 19 }
|
|
|
|
issPortCtrlPauseFloodStatsClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to clear the number of times the port entered pause flood condition."
|
|
DEFVAL { false }
|
|
::= { issPortCtrlEntry 20 }
|
|
|
|
issPortCtrlPauseFloodTraceOption OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to store the debug trace types that are enable by the user
|
|
for particular Interface. The bit positions of the traces is shown below.
|
|
Bit 0 - no trace
|
|
Bit 1 - init-shut
|
|
Bit 2 - mgmt
|
|
Bit 3 - sampling
|
|
Bit 4 - os resource
|
|
Bit 5 - entry
|
|
Bit 6 - exit"
|
|
DEFVAL { 0 }
|
|
::= { issPortCtrlEntry 21 }
|
|
|
|
issPortCtrlSwitchModeType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
cutThroughSameSpeed (1),
|
|
storeForward (2),
|
|
cutThroughSlowToFast (3),
|
|
cutThroughFastToSlow (4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to configure switching mode configuration
|
|
per port-level.
|
|
|
|
Switching mode can be configured only for physical ports.
|
|
|
|
When configured as StoreForward(2), the port operates in a
|
|
store-and-forward mode and the switch checks each frame for
|
|
cyclic redundancy check (CRC) errors before forwarding them
|
|
to the network. Each frame is stored until the entire frame
|
|
has been received and checked. Because the switch waits for
|
|
forwarding the frame until the entire frame has been received
|
|
and checked, the switching speed in Store-Forward switching
|
|
mode is slower than the switching speed in Cut-Through
|
|
switching modes.
|
|
|
|
When configured any of the cut-through modes, the switch
|
|
operates in Cut-Through switching mode and start forwarding
|
|
the frame as soon as the switch has read the destination
|
|
details in the packet header. A switch in Cut-Through mode
|
|
forwards the data before it has completed receiving the
|
|
entire frame. The switching speed in Cut-Through mode is
|
|
faster than the switching speed in Store-Forward switching
|
|
mode.
|
|
|
|
Switching mode configuration:
|
|
CutThroughSameSpeed(1) : Cut-through forwarding between same speed
|
|
ports
|
|
StoreForward(2) : Store and forward switching mode
|
|
CutThroughSlowToFast(3): Cut-through forwarding between slower to
|
|
faster speed ports.
|
|
CutThroughFastToSlow(4): Cut-through forwarding between faster to
|
|
slower speed ports.
|
|
NOTE:
|
|
Few platforms supports extended Cut-Through mode for ports with
|
|
mismatched speeds.(eg. slow-to-fast, fast-to-slow).
|
|
Platforms which doesn't support extended Cut-Through mode,
|
|
Cut-Through same speed shall be considered as Cut-Through
|
|
switching mode"
|
|
DEFVAL { storeForward }
|
|
::={ issPortCtrlEntry 22 }
|
|
|
|
issPortCtrlSwitchModeStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
cutThroughSameSpeed (1),
|
|
storeForward (2),
|
|
cutThroughSlowToFast (3),
|
|
cutThroughFastToSlow (4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is a read-only scalar MIB object to reflect the switching
|
|
mode configuration of the port in the hardware.
|
|
|
|
Switching mode configuration:
|
|
CutThroughSameSpeed(1) : Cut-through forwarding between same speed
|
|
ports
|
|
StoreForward(2) : Store and forward switching mode
|
|
CutThroughSlowToFast(3): Cut-through forwarding between slower to
|
|
faster speed ports.
|
|
CutThroughFastToSlow(4): Cut-through forwarding between faster to
|
|
slower speed ports.
|
|
NOTE:
|
|
Few platforms supports extended Cut-Through mode for ports with
|
|
mismatched speeds.(eg. slow-to-fast, fast-to-slow).
|
|
Platforms which doesn't support extended Cut-Through mode,
|
|
Cut-Through same speed shall be considered as Cut-Through
|
|
switching mode"
|
|
|
|
::={ issPortCtrlEntry 23 }
|
|
|
|
issPortCtrlInbandAutoNeg OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
on(1),
|
|
off(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable or disable the CPSS inband auto-negotiation.
|
|
This is required by certain 1G transceivers."
|
|
::={ issPortCtrlEntry 24 }
|
|
|
|
issPortCtrlBypassInbandAutoNeg OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
on(1),
|
|
off(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable or disable the CPSS bypass inband auto-negotiation.
|
|
When this is enabled auto-negotiation may be bypassed when negotiating link if one side does not respond.
|
|
This is required by certain 1G transceivers."
|
|
::={ issPortCtrlEntry 25 }
|
|
|
|
issPortCtrlForceSpeed OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
on(1),
|
|
off(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to detect manual speed settings on sfp ports."
|
|
::={ issPortCtrlEntry 26 }
|
|
-- ------------------------------------------------------------------
|
|
-- Port Isolation Table
|
|
-- ------------------------------------------------------------------
|
|
|
|
issPortIsolationTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssPortIsolationEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to configure the port isolation feature.
|
|
For a given port, user can configure the list of allowed
|
|
forwarding/egress ports, where the packets for particular vlan that
|
|
ingress the port can be forwarded. If the Vlan is not given, then
|
|
the rule will be applied for all packets that ingress the given port.
|
|
|
|
This table can be configured only for physical and link aggregated
|
|
ports.
|
|
|
|
Before a packet is sent out of a port (after all L2/L3 processing), port
|
|
isolation table entry is referred for the ingress port of that packet.
|
|
If an entry is present for that ingress port and if the outgoing port
|
|
is configured as one of the egress ports , then the packet
|
|
will be transmitted out of that outgoing port. Otherwise the packet
|
|
will be dropped.
|
|
|
|
If there is no entry configured for that ingress port in this
|
|
table, then the packet will be transmitted on that outgoing port."
|
|
::= { issConfigControl 3 }
|
|
|
|
issPortIsolationEntry OBJECT-TYPE
|
|
SYNTAX IssPortIsolationEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each etnry in this table gives a ingress port to egress port mapping."
|
|
INDEX { issPortIsolationIngressPort, issPortIsolationInVlanId, issPortIsolationEgressPort}
|
|
::= { issPortIsolationTable 1 }
|
|
|
|
IssPortIsolationEntry ::=
|
|
SEQUENCE {
|
|
issPortIsolationIngressPort
|
|
InterfaceIndex,
|
|
issPortIsolationInVlanId
|
|
Integer32,
|
|
issPortIsolationEgressPort
|
|
InterfaceIndex,
|
|
issPortIsolationStorageType
|
|
StorageType,
|
|
issPortIsolationRowStatus
|
|
RowStatus
|
|
}
|
|
|
|
issPortIsolationIngressPort OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object speficies the IfIndex of the ingress port. This port can
|
|
be a physical or link aggregated port."
|
|
::= { issPortIsolationEntry 1 }
|
|
|
|
issPortIsolationInVlanId OBJECT-TYPE
|
|
SYNTAX Integer32 (0..4094)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If this object value is non-zero, then the port isolation rule is
|
|
applied for all packets received on the given ingress port.
|
|
Otherwise the rule is applied for this vlan packets received on the
|
|
given ingress port."
|
|
::= { issPortIsolationEntry 2 }
|
|
|
|
issPortIsolationEgressPort OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies one of the allowed egress ports for the given
|
|
ingress port identified by the first index for this row.
|
|
This port can be either a physical or link aggregated port."
|
|
::= { issPortIsolationEntry 3 }
|
|
|
|
issPortIsolationStorageType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the storage type of this entry.
|
|
Only 'volatile' and 'nonVolatile' values are allowed for this object.
|
|
'readOnly', 'permenant' and 'other' values are not allowed for this
|
|
object.
|
|
|
|
If this table is configured for an ingress port and InVlanId via
|
|
management, then the issPortIsolationStorageType for all the entries
|
|
with this ingress port as primary index and this InVlanId as
|
|
secondary index will have the values as 'nonVolatile'.
|
|
Otherwise it will be set to 'volatile'.
|
|
|
|
Entries in this table will be restored on reboot, only if the
|
|
corresponding issPortIsolationStorageType object is set as
|
|
nonVolatile."
|
|
::= { issPortIsolationEntry 4 }
|
|
|
|
|
|
issPortIsolationRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Denotes the Row Status for port isolation table entry.
|
|
Only 'CreateAndGo' and 'destroy' values are allowed for this
|
|
object. 'CreateAndWait' and 'notInService' values are not allowed.
|
|
Example:
|
|
To add ports 2, 3 as egress ports for ingress port 1 in this table,
|
|
the following sequence to be followed:
|
|
|
|
1. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
|
|
entry with index
|
|
(issPortIsolationIngressPort = 1, issPortIsolationInVlanId =0,
|
|
issPortIsolationEgressPort = 2)
|
|
2. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
|
|
entry with index
|
|
(issPortIsolationIngressPort = 1, issPortIsolationInVlanId =0,
|
|
issPortIsolationEgressPort = 3)
|
|
|
|
To add ports 5, 6 as egress ports for ingress port 7 and for vlan 5
|
|
in this table, the following sequence to be followed:
|
|
|
|
1. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
|
|
entry with index
|
|
(issPortIsolationIngressPort = 7, issPortIsolationInVlanId =5,
|
|
issPortIsolationEgressPort = 5)
|
|
2. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
|
|
entry with index
|
|
(issPortIsolationIngressPort = 7, issPortIsolationInVlanId =5,
|
|
issPortIsolationEgressPort = 6)
|
|
|
|
To delete a egress port 3 from the list of egress ports for ingress
|
|
port 1 do the following:
|
|
Set the issPortIsolationRowStatus as 'destroy' for the
|
|
entry with index
|
|
(issPortIsolationIngressPort = 1, issPortIsolationEgressPort = 3)"
|
|
|
|
::= { issPortIsolationEntry 5 }
|
|
|
|
-- Mirror Group ------------------------------------------------------
|
|
|
|
issMirrorStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled (1),
|
|
enabled (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable mirroring
|
|
feature in hardware.
|
|
When set to 'disabled (1)', all mirroring configurations will be
|
|
removed from hardware.
|
|
When set to 'enabled (2)', all mirroring configurations
|
|
present in software will be programmed in hardware."
|
|
|
|
DEFVAL { enabled }
|
|
::= { issMirror 1 }
|
|
|
|
issMirrorToPort OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the port to which the active mirrored traffic controlled
|
|
by issMirrorCtrlTable is to be copied."
|
|
::= { issMirror 2 }
|
|
|
|
-- Mirror Control Table
|
|
|
|
issMirrorCtrlTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssMirrorCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to control mirroring features for each interface
|
|
in the switch.
|
|
|
|
Parameters in this table are valid only when the
|
|
'issMirrorStatus' for the switch is not 'disabled'."
|
|
::= { issMirror 3 }
|
|
|
|
issMirrorCtrlEntry OBJECT-TYPE
|
|
SYNTAX IssMirrorCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each interface
|
|
in the system."
|
|
INDEX { issMirrorCtrlIndex }
|
|
::= { issMirrorCtrlTable 1 }
|
|
|
|
IssMirrorCtrlEntry ::=
|
|
SEQUENCE {
|
|
issMirrorCtrlIndex
|
|
Integer32,
|
|
issMirrorCtrlIngressMirroring
|
|
INTEGER,
|
|
issMirrorCtrlEgressMirroring
|
|
INTEGER,
|
|
issMirrorCtrlStatus
|
|
INTEGER
|
|
}
|
|
|
|
issMirrorCtrlIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The interface index of the port for which the configuration
|
|
in this entry applies."
|
|
::= { issMirrorCtrlEntry 1 }
|
|
|
|
issMirrorCtrlIngressMirroring OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Provides control to enable or disable mirroring of ingress
|
|
traffic over this interface to the mirrored-to port."
|
|
DEFVAL { disabled }
|
|
::= { issMirrorCtrlEntry 2 }
|
|
|
|
issMirrorCtrlEgressMirroring OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Provides control to enable or disable mirroring of egress
|
|
traffic over this interface to the mirrored-to port."
|
|
DEFVAL { disabled }
|
|
::= { issMirrorCtrlEntry 3 }
|
|
|
|
issMirrorCtrlStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
valid(1),
|
|
invalid(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the validity of the entry."
|
|
::= { issMirrorCtrlEntry 4 }
|
|
|
|
-- Mirror Control Extension Table
|
|
|
|
issMirrorCtrlRemainingSrcRcrds OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the number of source records remaining in the system.
|
|
Each record can store at least one source information. In case
|
|
consecutive source id are configured then record will store the range"
|
|
::= { issMirror 4 }
|
|
|
|
issMirrorCtrlRemainingDestRcrds OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the number of destination records remaining in the system.
|
|
Each record can store at least one destination information. In case
|
|
consecutive destination id are configured then record will store the
|
|
range"
|
|
::= { issMirror 5 }
|
|
|
|
issMirrorCtrlExtnTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssMirrorCtrlExtnEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This Table is used to configure advanced mirroring features like
|
|
- Port Based Mirroring:
|
|
- flow based mirroring
|
|
- vlan based mirroring
|
|
|
|
Following are the configuration details for Port based mirroring:
|
|
To configure source ports in a session
|
|
- issMirrorCtrlExtnMirrType - is set to portBased
|
|
- issMirrorCtrlExtnSrcTable - should be used to configure list
|
|
of source ports to be mirrored
|
|
in a session
|
|
- issMirrorCtrlExtnSrcId - represents the source port.
|
|
The port Id to be mirrored
|
|
should be given here.
|
|
- issMirrorCtrlExtnSrcCfg - this object is used to
|
|
add/remove a port in the
|
|
source port list
|
|
|
|
Example
|
|
To create a session 1 with source ports 5,6 following
|
|
sequence of configuration should be followed
|
|
For table issMirrorCtrlExtnTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnMirrType = portBased
|
|
|
|
For table issMirrorCtrlExtnSrcTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnSrcId = 5 as index
|
|
issMirrorCtrlExtnSrcCfg = add
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnSrcId = 6 as index
|
|
issMirrorCtrlExtnSrcCfg = add
|
|
|
|
To configure destination ports in a session
|
|
- issMirrorCtrlExtnDestinationTable - should be used to
|
|
configure list of
|
|
destination ports to be
|
|
mirrored in a session
|
|
- issMirrorCtrlExtnDestination - represents the
|
|
destination port. The
|
|
port Id to which packets
|
|
should be mirrored should
|
|
be given here.
|
|
- issMirrorCtrlExtnDestCfg - this object is used to
|
|
add/remove a port in the
|
|
source port list.
|
|
Example
|
|
To create a session 1 with destination port 10,11 following
|
|
sequence of configuration should be followed
|
|
For table issMirrorCtrlExtnTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnMirrType = portBased
|
|
|
|
For table issMirrorCtrlExtnDestinationTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnDestination = 10 as index
|
|
issMirrorCtrlExtnDestCfg = add
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnDestination = 11 as index
|
|
issMirrorCtrlExtnDestCfg = add
|
|
|
|
To Activate a session
|
|
- issMirrorCtrlExtnStatus - should be used to
|
|
activate/deactivate mirroring for a
|
|
session
|
|
Example
|
|
To enable mirroring for a session following sequence of
|
|
configuration should be followed
|
|
For table issMirrorCtrlExtnTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnStatus = active
|
|
|
|
Above configurations applies to flow based mirroring also, the
|
|
issMirrorCtrlExtnSrcId used above for configuratin ports
|
|
should be used to configure flow Id
|
|
|
|
To enable remote monitoring of sources for a session
|
|
- issMirrorCtrlExtnRSpanStatus - should be used to
|
|
enable/disable remote
|
|
monitoring for a session
|
|
it can be used to set a
|
|
session as source rspan
|
|
session which implies source
|
|
entities for this session are
|
|
monitored remotely or can be
|
|
used to set a session
|
|
as destination rspan session
|
|
which implies that mirrored
|
|
data is received for this
|
|
session should be forwarded to
|
|
destination entities of this
|
|
session
|
|
- issMirrorCtrlExtnRSpanVlanId - it is the vlan id which is
|
|
reserved in the network to
|
|
carry Mirrored data,if the
|
|
session is configured as
|
|
source rspan session then data
|
|
mirrored for the source
|
|
entities will be forwarded on
|
|
this vlan if the session is
|
|
configured as destination
|
|
rspan session then data
|
|
received on this vlan will be
|
|
forwarded to the destination
|
|
entities of this session
|
|
|
|
Following are the configuration details for configurating Vlan
|
|
based mirroring:
|
|
To configure vlans as source for a session
|
|
- issMirrorCtrlExtnMirrType - is set to vlanBased
|
|
- issMirrorCtrlExtnSrcVlanTable - should be used to configure
|
|
list of source vlans to be
|
|
mirrored in a session
|
|
- issMirrorCtrlExtnSrcVlanId - represents a source vlan. The
|
|
vlan to be mirrored should be
|
|
given here.
|
|
- issMirrorCtrlExtnSrcVlanCfg - this object is used to
|
|
add/remove a vlan in the
|
|
source vlan list
|
|
Example
|
|
To create a session 1 with source list as vlan 5,6
|
|
belonging to context 1 following sequence of configuration
|
|
should be followed
|
|
For table issMirrorCtrlExtnTable
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnMirrType = vlanBased
|
|
|
|
For table issMirrorCtrlExtnSrcVlanTable
|
|
issMirrorCtrlExtnSrcVlanContext = 1 as index
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnSrcVlanId = 5 as index
|
|
issMirrorCtrlExtnSrcVlanCfg = add
|
|
issMirrorCtrlExtnSrcVlanContext = 1 as index
|
|
issMirrorCtrlExtnSessionIndex = 1 as index
|
|
issMirrorCtrlExtnSrcVlanId = 6 as index
|
|
issMirrorCtrlExtnSrcVlanCfg = add
|
|
|
|
Entries for this table can be configured only when issMirrorStatus
|
|
is set to enabled.
|
|
Configurations done through 'issMirrorCtrlTable' will change the
|
|
following for the first session on this table:
|
|
- Mirroring type will be changed to port-based
|
|
- Mode and Source entities will be overwritten
|
|
with the values configured through 'issMirrorCtrlTable'
|
|
- Destination entities will be overwritten
|
|
with the value configured through 'issMirrorToPort' object "
|
|
::= { issMirror 6 }
|
|
|
|
issMirrorCtrlExtnEntry OBJECT-TYPE
|
|
SYNTAX IssMirrorCtrlExtnEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each session
|
|
in the system."
|
|
INDEX { issMirrorCtrlExtnSessionIndex}
|
|
::= { issMirrorCtrlExtnTable 1 }
|
|
|
|
IssMirrorCtrlExtnEntry ::=
|
|
SEQUENCE {
|
|
issMirrorCtrlExtnSessionIndex
|
|
Integer32,
|
|
issMirrorCtrlExtnMirrType
|
|
INTEGER,
|
|
issMirrorCtrlExtnRSpanStatus
|
|
INTEGER,
|
|
issMirrorCtrlExtnRSpanVlanId
|
|
Integer32,
|
|
issMirrorCtrlExtnRSpanContext
|
|
Integer32,
|
|
issMirrorCtrlExtnStatus
|
|
RowStatus
|
|
}
|
|
|
|
issMirrorCtrlExtnSessionIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..20)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index of the mirroring session for which the configuration
|
|
in this entry applies."
|
|
::= { issMirrorCtrlExtnEntry 1 }
|
|
|
|
issMirrorCtrlExtnMirrType OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
portBased(1),
|
|
macflowBased(2),
|
|
vlanBased(3),
|
|
invalid(4),
|
|
ipflowBased(5)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object tells the type of mirroring this session supports.
|
|
This object needs to be set before doing any configuration for
|
|
a mirroring session"
|
|
DEFVAL { invalid }
|
|
::= { issMirrorCtrlExtnEntry 2 }
|
|
|
|
issMirrorCtrlExtnRSpanStatus OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
sourceRSpanVlan(1),
|
|
destinationRSpanVlan(2),
|
|
disabled(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates session is enabled or disabled for
|
|
Remote monitoring.
|
|
If set as 'source-rspan-vlanid' indicates that the session is
|
|
enabled for Remote monitoring and the source entities for this
|
|
session will be remotely monitored.
|
|
If set as 'destination-rspan-vlanid' indicates that the session
|
|
should monitor remote traffic mirrored with RSPAN VLAN ID tag.
|
|
RSPAN VLAN ID should be configured through object
|
|
'issMirrorCtrlExtnRSpanVlanId'.
|
|
If set as 'disabled' Remote monitoring is disabled for this
|
|
mirroring session."
|
|
|
|
DEFVAL { disabled }
|
|
::= { issMirrorCtrlExtnEntry 3 }
|
|
|
|
issMirrorCtrlExtnRSpanVlanId OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Vlan Id used for Remote monitoring for this session.
|
|
If issMirrorCtrlExtnRSpanStatus is set to disabled, then
|
|
this object will have an invalid value (zero)"
|
|
DEFVAL { 0 }
|
|
::= { issMirrorCtrlExtnEntry 4 }
|
|
|
|
issMirrorCtrlExtnRSpanContext OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the Context Id to which the RSpan Vlan belongs.
|
|
Value '0' mean this object is not considered for this
|
|
mirroring session."
|
|
DEFVAL { 0 }
|
|
::= { issMirrorCtrlExtnEntry 5 }
|
|
|
|
issMirrorCtrlExtnStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the status of the entry. The entry can be
|
|
made active only if issMirrorCtrlExtnMirrType is configured and
|
|
source and destination entries for this sesion is also configured"
|
|
::= { issMirrorCtrlExtnEntry 6 }
|
|
|
|
issMirrorCtrlExtnSrcTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssMirrorCtrlExtnSrcEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to configure list of source entities for mirroring sessions"
|
|
::= { issMirror 7 }
|
|
|
|
issMirrorCtrlExtnSrcEntry OBJECT-TYPE
|
|
SYNTAX IssMirrorCtrlExtnSrcEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each mirroring session."
|
|
INDEX { issMirrorCtrlExtnSessionIndex, issMirrorCtrlExtnSrcId }
|
|
::= { issMirrorCtrlExtnSrcTable 1 }
|
|
|
|
IssMirrorCtrlExtnSrcEntry ::=
|
|
SEQUENCE {
|
|
issMirrorCtrlExtnSrcId
|
|
Integer32,
|
|
issMirrorCtrlExtnSrcCfg
|
|
INTEGER,
|
|
issMirrorCtrlExtnSrcMode
|
|
INTEGER
|
|
}
|
|
|
|
issMirrorCtrlExtnSrcId OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the source id which participates in a mirroring session.
|
|
For Port based mirroring this object can be port IfIndex.
|
|
To mirror Tunnel and Trunk ports the same Id can be used for
|
|
specifying Tunnel/Trunk Id.
|
|
For Flow based mirroring this object can be Acl Ids."
|
|
::= { issMirrorCtrlExtnSrcEntry 1 }
|
|
|
|
issMirrorCtrlExtnSrcCfg OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
add(1),
|
|
delete(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create/delete a source entry for a session."
|
|
::= { issMirrorCtrlExtnSrcEntry 2 }
|
|
|
|
issMirrorCtrlExtnSrcMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ingress(1),
|
|
egress(2),
|
|
both(3),
|
|
disable(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Provides control to set the mode of mirroring.
|
|
It can be ingress, egress, both or disable."
|
|
DEFVAL { both }
|
|
::= { issMirrorCtrlExtnSrcEntry 3 }
|
|
|
|
issMirrorCtrlExtnSrcVlanTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssMirrorCtrlExtnSrcVlanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to configure list of vlan source entities for mirroring sessions"
|
|
::= { issMirror 8 }
|
|
|
|
issMirrorCtrlExtnSrcVlanEntry OBJECT-TYPE
|
|
SYNTAX IssMirrorCtrlExtnSrcVlanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each mirroring session."
|
|
INDEX { issMirrorCtrlExtnSessionIndex, issMirrorCtrlExtnSrcVlanContext, issMirrorCtrlExtnSrcVlanId }
|
|
::= { issMirrorCtrlExtnSrcVlanTable 1 }
|
|
|
|
IssMirrorCtrlExtnSrcVlanEntry ::=
|
|
SEQUENCE {
|
|
issMirrorCtrlExtnSrcVlanContext
|
|
Integer32,
|
|
issMirrorCtrlExtnSrcVlanId
|
|
Integer32,
|
|
issMirrorCtrlExtnSrcVlanCfg
|
|
INTEGER,
|
|
issMirrorCtrlExtnSrcVlanMode
|
|
INTEGER
|
|
}
|
|
|
|
issMirrorCtrlExtnSrcVlanContext OBJECT-TYPE
|
|
SYNTAX Integer32 (1..64)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the Context Id to which the source entity belongs, this
|
|
is used in case of specifying vlan as source.
|
|
Value '-1' mean this object is not considered for this mirroring
|
|
session."
|
|
::= { issMirrorCtrlExtnSrcVlanEntry 1 }
|
|
|
|
issMirrorCtrlExtnSrcVlanId OBJECT-TYPE
|
|
SYNTAX Integer32 (1..4094)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the Vlan id which participates in a mirroring session."
|
|
::= { issMirrorCtrlExtnSrcVlanEntry 2 }
|
|
|
|
issMirrorCtrlExtnSrcVlanCfg OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
add(1),
|
|
delete(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create/delete a vlan entry for a session."
|
|
::= { issMirrorCtrlExtnSrcVlanEntry 3 }
|
|
|
|
issMirrorCtrlExtnSrcVlanMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ingress(1),
|
|
egress(2),
|
|
both(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Provides control to set the mode of mirroring.
|
|
It can be ingerss,Egress or Both."
|
|
DEFVAL { both }
|
|
::= { issMirrorCtrlExtnSrcVlanEntry 4 }
|
|
|
|
issMirrorCtrlExtnDestinationTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssMirrorCtrlExtnDestinationEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to configure list of destination entities"
|
|
::= { issMirror 9 }
|
|
|
|
issMirrorCtrlExtnDestinationEntry OBJECT-TYPE
|
|
SYNTAX IssMirrorCtrlExtnDestinationEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry appears in this table for each destination entity
|
|
in a mirroring session."
|
|
INDEX { issMirrorCtrlExtnSessionIndex, issMirrorCtrlExtnDestination }
|
|
::= { issMirrorCtrlExtnDestinationTable 1 }
|
|
|
|
IssMirrorCtrlExtnDestinationEntry ::=
|
|
SEQUENCE {
|
|
issMirrorCtrlExtnDestination
|
|
Integer32,
|
|
issMirrorCtrlExtnDestCfg
|
|
INTEGER
|
|
}
|
|
|
|
issMirrorCtrlExtnDestination OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the destination port id which participates in a mirroring
|
|
session."
|
|
::= { issMirrorCtrlExtnDestinationEntry 1 }
|
|
|
|
issMirrorCtrlExtnDestCfg OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
add (1),
|
|
delete (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create/delete a destination entry for a session."
|
|
::= { issMirrorCtrlExtnDestinationEntry 2 }
|
|
|
|
issCpuMirrorType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ingress (1),
|
|
egress (2),
|
|
both (3),
|
|
disable (4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to set the type of mirroring
|
|
to be done for CPU traffic.
|
|
When set to 'ingress(1)', enables mirroring of ingress
|
|
traffic over CPU port to the CPU mirrored-to port
|
|
specified in 'issCpuMirrorToPort'.
|
|
When set to 'egress(2)', enables mirroring of egress
|
|
traffic over CPU port to the CPU mirrored-to port.
|
|
specified in 'issCpuMirrorToPort'.
|
|
When set to 'both(3)', enables mirroring of egress and ingress
|
|
traffic over CPU port to the CPU mirrored-to port
|
|
specified in 'issCpuMirrorToPort'.
|
|
When set to 'disable(4)', CPU mirroring configuration will be
|
|
removed."
|
|
|
|
DEFVAL { disable }
|
|
::= { issMirror 10 }
|
|
|
|
issCpuMirrorToPort OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the physical port to which the CPU traffic specified
|
|
by issCpuMirrorType are mirrored."
|
|
DEFVAL { 0 }
|
|
::= { issMirror 11 }
|
|
|
|
-- ------------------------------------------------------------------
|
|
-- IP Authorized Manager
|
|
|
|
issIpAuthMgrTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssIpAuthMgrEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table to configure IP authorized managers in the system."
|
|
::= { issIpAuthMgr 1 }
|
|
|
|
issIpAuthMgrEntry OBJECT-TYPE
|
|
SYNTAX IssIpAuthMgrEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry in this table represents rules for particular
|
|
IP authorized manager."
|
|
INDEX { issIpAuthMgrIpAddr, issIpAuthMgrIpMask }
|
|
::= { issIpAuthMgrTable 1 }
|
|
|
|
IssIpAuthMgrEntry ::=
|
|
SEQUENCE {
|
|
issIpAuthMgrIpAddr
|
|
IpAddress,
|
|
issIpAuthMgrIpMask
|
|
IpAddress,
|
|
issIpAuthMgrPortList
|
|
PortList,
|
|
issIpAuthMgrVlanList
|
|
OCTET STRING,
|
|
issIpAuthMgrOOBPort
|
|
TruthValue,
|
|
issIpAuthMgrAllowedServices
|
|
Integer32,
|
|
issIpAuthMgrRowStatus
|
|
RowStatus
|
|
}
|
|
|
|
issIpAuthMgrIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies either the Network or Host address from which the switch
|
|
can be managed.
|
|
An address 0.0.0.0 indicates 'Any Manager'."
|
|
::= { issIpAuthMgrEntry 1 }
|
|
|
|
issIpAuthMgrIpMask OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the IP address mask to be applied on issIpAuthMgrIpAddr.
|
|
Value 0.0.0.0 indicates mask for 'Any Manager'."
|
|
::= { issIpAuthMgrEntry 2 }
|
|
|
|
issIpAuthMgrPortList OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the port numbers through which the authorized manager can
|
|
access the switch.
|
|
|
|
By default the authorized manager is allowed to access the switch
|
|
through all the ports.
|
|
|
|
If a set of ports are configured in the 'PortList', the manager can
|
|
access the switch only through the configured ports."
|
|
::= { issIpAuthMgrEntry 3 }
|
|
|
|
issIpAuthMgrVlanList OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the Vlan's in which the IP authorized manager can reside.
|
|
By default the manager is allowed to reside in any vlan.
|
|
|
|
If a set of vlans are configured in the 'VlanList', the manager can
|
|
reside only in the configured vlan set. Access to the switch
|
|
will be denied from any other vlan."
|
|
::= { issIpAuthMgrEntry 4 }
|
|
|
|
issIpAuthMgrOOBPort OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies whether the authorized manager can access the switch
|
|
through OOB Port
|
|
By default the manager is denied access to reside on OOB Interface"
|
|
DEFVAL { false }
|
|
::= { issIpAuthMgrEntry 5 }
|
|
|
|
issIpAuthMgrAllowedServices OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the allowed services through which the authorized manager can
|
|
access the switch.
|
|
This object takes bit mask values. The services represented by each bit
|
|
position is as given below:
|
|
|
|
With bit 0 being the Least Significant Bit,
|
|
|
|
Bit0 --> snmp
|
|
Bit1 --> telnet
|
|
Bit2 --> http
|
|
Bit3 --> https
|
|
Bit4 --> ssh
|
|
|
|
If the particular bit is set to 1,corresponding service is allowed for
|
|
the configured manager.
|
|
|
|
By default all services are allowed for the configured manager."
|
|
|
|
DEFVAL { '1F'h }
|
|
::= { issIpAuthMgrEntry 6 }
|
|
|
|
issIpAuthMgrRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the status of this entry."
|
|
::= { issIpAuthMgrEntry 7 }
|
|
|
|
|
|
-- Iss Extension Group ------------------------------------
|
|
-- Rate Control Group --------------------------------------------- --
|
|
|
|
issRateCtrlTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssRateCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A table to control the rate limiting parameters
|
|
either for the entire switch or for each interface in the switch.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
::= { issRateControl 1 }
|
|
|
|
issRateCtrlEntry OBJECT-TYPE
|
|
SYNTAX IssRateCtrlEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"An entry appears in this table for each physical
|
|
interface in the switch.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
INDEX { issRateCtrlIndex }
|
|
::= { issRateCtrlTable 1 }
|
|
|
|
IssRateCtrlEntry ::=
|
|
SEQUENCE {
|
|
issRateCtrlIndex
|
|
Integer32,
|
|
issRateCtrlDLFLimitValue
|
|
Integer32,
|
|
issRateCtrlBCASTLimitValue
|
|
Integer32,
|
|
issRateCtrlMCASTLimitValue
|
|
Integer32,
|
|
issRateCtrlPortRateLimit
|
|
Integer32,
|
|
issRateCtrlPortBurstSize
|
|
Integer32
|
|
}
|
|
|
|
issRateCtrlIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The interface index for which the configuration in this
|
|
entry applies.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
::= { issRateCtrlEntry 1 }
|
|
|
|
issRateCtrlDLFLimitValue OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Allows to configure the limiting value for the maximum number
|
|
of dlf packets that can be transmitted per second over this interface.
|
|
Setting this object to the value zero disables rate limiting for
|
|
Destination lookup failure packets on this interface. The value that
|
|
can be set for this object is limited by the underlying hardware
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
|
|
DEFVAL {0}
|
|
::= { issRateCtrlEntry 2 }
|
|
|
|
issRateCtrlBCASTLimitValue OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Allows to configure the limiting value for the maximum number
|
|
of broadcast packets that can be transmitted per second over this
|
|
interface. Setting this object to the value zero disables rate
|
|
limiting for Broadcast packets on this interface. The value that
|
|
can be set for this object is limited by the underlying hardware
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
|
|
DEFVAL {0}
|
|
::= { issRateCtrlEntry 3 }
|
|
|
|
|
|
issRateCtrlMCASTLimitValue OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Allows to configure the limiting value for the maximum number
|
|
of multicast packets that can be transmitted per second over this
|
|
interface. Setting this object to the value zero disables rate
|
|
limiting for Multicast packets on this interface. The value that
|
|
can be set for this object is limited by the underlying hardware
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
|
|
DEFVAL {0}
|
|
::= { issRateCtrlEntry 4}
|
|
|
|
issRateCtrlPortRateLimit OBJECT-TYPE
|
|
SYNTAX Integer32 (0..80000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Configures interface Rate Limit (Packet that can be transferred
|
|
on a port at a particular second).
|
|
|
|
This object's value will take effect on the interface speed. Based
|
|
on the operating speed of the port, the rate limit will be applied.
|
|
This value can also be affected by the metering. A value of zero(0)
|
|
disable rate limiting i.e. sets the port to full speed.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
|
|
::= { issRateCtrlEntry 5 }
|
|
|
|
issRateCtrlPortBurstSize OBJECT-TYPE
|
|
SYNTAX Integer32 (0..80000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Configures interface Burst Pkt Rate. (Packet Burst that can be
|
|
transferred on a port at a particular second)
|
|
|
|
This object's value will take effect on the interface speed. Based
|
|
on the operating speed of the port, the burst size of the port
|
|
will be applied. This value can also be affected by the metering. A
|
|
value of zero(0) disable burst rate limiting i.e. sets the port burst
|
|
rate limit to full speed.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issRateControl objects in fsissext.mib."
|
|
|
|
::= { issRateCtrlEntry 6 }
|
|
|
|
|
|
|
|
|
|
-- ------------------------------------------------------------------
|
|
-- L2 Filter Group --------------------------------------------------
|
|
|
|
issL2FilterTable OBJECT-TYPE
|
|
|
|
SYNTAX SEQUENCE OF IssL2FilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A table to configure L2 filter rules in the system.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2Filter 1 }
|
|
|
|
issL2FilterEntry OBJECT-TYPE
|
|
SYNTAX IssL2FilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Each entry in this table is a L2 filter rule.Index to the table
|
|
is the L2 filter number.This object is deprecated and the
|
|
corresponding functionality is met with issL2Filter objects
|
|
in fsissext.mib."
|
|
|
|
INDEX { issL2FilterNo}
|
|
::= { issL2FilterTable 1 }
|
|
|
|
IssL2FilterEntry ::=
|
|
SEQUENCE {
|
|
issL2FilterNo
|
|
Integer32,
|
|
issL2FilterPriority
|
|
Integer32,
|
|
issL2FilterEtherType
|
|
Integer32,
|
|
issL2FilterProtocolType
|
|
Unsigned32,
|
|
issL2FilterDstMacAddr
|
|
MacAddress,
|
|
issL2FilterSrcMacAddr
|
|
MacAddress,
|
|
issL2FilterVlanId
|
|
Integer32,
|
|
issL2FilterInPortList
|
|
PortList,
|
|
issL2FilterAction
|
|
INTEGER,
|
|
issL2FilterMatchCount
|
|
Counter32,
|
|
issL2FilterStatus
|
|
RowStatus,
|
|
issL2FilterOutPortList
|
|
PortList,
|
|
issL2FilterDirection
|
|
INTEGER
|
|
|
|
}
|
|
|
|
issL2FilterNo OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"L2 Filter rule number.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 1 }
|
|
|
|
issL2FilterPriority OBJECT-TYPE
|
|
SYNTAX Integer32 (1..255)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The priority of the L2 filter can be used to decide which filter rule
|
|
is applicable when
|
|
--> the packet matches with more than one filter rules
|
|
--> All the filter rules result in 'allow'ing the packet
|
|
|
|
Higher value of 'filter priority' implies a higher priority.
|
|
|
|
Usage of 'L2FilterPriority' is implementation dependant.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { 1 }
|
|
::= { issL2FilterEntry 2 }
|
|
|
|
issL2FilterEtherType OBJECT-TYPE
|
|
SYNTAX Integer32 (0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The value in the Type/Len field of a frame that will
|
|
be matched to trigger this filter. The default value of
|
|
this object is '0'. When this object is SET with the default
|
|
value, frames are not matched for the value in the Type/Len
|
|
field with the value set for this object.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { 0 }
|
|
::= { issL2FilterEntry 3 }
|
|
|
|
|
|
issL2FilterProtocolType OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the non IP protocol type to be filtered.
|
|
aarp | amber | dec-spanning | decnet-iv |
|
|
diagnostic | dsm |etype-6000 | etype-8042 |
|
|
lat | lavc-sca | mop-console | mop-dump |
|
|
msdos | mumps | netbios | vines-echo |
|
|
vines-ip | xns-idp: A non-IP protocol.
|
|
|
|
A value of '0' means, the filter is applicable for all protocols.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { 0 }
|
|
::= { issL2FilterEntry 4 }
|
|
|
|
issL2FilterDstMacAddr OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Destination MAC address to be matched with the packet. By Default, the
|
|
Destination Mac Address will be zero which means dont care condition ie)
|
|
any Dst Mac Address .This object is deprecated and the corresponding
|
|
functionality is met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 5 }
|
|
|
|
issL2FilterSrcMacAddr OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Source MAC address to be matched with the packet. By Default, the Source
|
|
Mac Address will be zero which means dont care condition ie) any Src Mac
|
|
address This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 6 }
|
|
|
|
|
|
issL2FilterVlanId OBJECT-TYPE
|
|
SYNTAX Integer32 (0..4094)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will
|
|
be treated as customer Vlan Id.
|
|
A value of '0' means, this object is unused. Configuring this value is not
|
|
allowed.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { 0 }
|
|
::= { issL2FilterEntry 7 }
|
|
|
|
|
|
issL2FilterInPortList OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the complete set of ports over which this filter is applied
|
|
for packets ingress at ports in this list.
|
|
If the In port list is '0', the filter rule is applicable for the
|
|
incoming packets on all ports.
|
|
Even though the issL2FilterInPortList is configured, It is applicable only
|
|
if issL2FilterDirection is configured as 'in'.
|
|
By default inport list is maintained as '0'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 8 }
|
|
|
|
issL2FilterAction OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
allow (1),
|
|
drop (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the action to be taken on the packet if the filter
|
|
rule matches.
|
|
If the action is 'allow', the packet will be forwarded according
|
|
to the forwarding rules.
|
|
If the action is 'drop', the packet will be discarded.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { allow }
|
|
::= { issL2FilterEntry 9 }
|
|
|
|
issL2FilterMatchCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Number of times this filter is matched.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
|
|
::= { issL2FilterEntry 10 }
|
|
|
|
issL2FilterStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This object indicates the status of this entry. An entry is
|
|
created in this table when this object is SET to 'createAndWait'.
|
|
The entry in this table is used when the status of this object
|
|
is SET 'active'. The entry in this table is not used when this
|
|
object is SET 'notInService'. An entry created in this table is
|
|
be deleted when this object is SET 'destroy'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 11 }
|
|
|
|
issL2FilterOutPortList OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the complete set of ports over which this filter is applied
|
|
for packets egress at Ports in this list.
|
|
If the Out port list is '0', the filter rule is applicable for the
|
|
outgoing packets on all ports.
|
|
Even though the issL2FilterOutPortList is configured, It is applicable only
|
|
if issL2FilterDirection is configured as 'out'.
|
|
By default outport list is maintained as '0'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
::= { issL2FilterEntry 12 }
|
|
|
|
issL2FilterDirection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
in (1),
|
|
out (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the direction of this filter to be applied. By Default the
|
|
filter will be applied on ingress direction.
|
|
When the direction of this filter is 'in', It is applied on specified
|
|
ports of the issL2FilterInPortList.
|
|
When the direction of this filter is 'out', It is applied on specified
|
|
ports of the issL2FilterOutPortList.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL2Filter objects in fsissext.mib."
|
|
DEFVAL { in }
|
|
::= { issL2FilterEntry 13 }
|
|
|
|
-- ------------------------------------------------------------------
|
|
-- L3 Filter Group --------------------------------------------------
|
|
|
|
|
|
issL3FilterTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssL3FilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" A table to configure L3 filter rules in the system.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3Filter 1 }
|
|
|
|
issL3FilterEntry OBJECT-TYPE
|
|
SYNTAX IssL3FilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" Each entry in this table is a L3 filter rule.
|
|
Index to the table is L3 filter number.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
INDEX { issL3FilterNo}
|
|
::= { issL3FilterTable 1 }
|
|
|
|
IssL3FilterEntry ::=
|
|
SEQUENCE {
|
|
issL3FilterNo
|
|
Integer32,
|
|
issL3FilterPriority
|
|
Integer32,
|
|
issL3FilterProtocol
|
|
Integer32,
|
|
issL3FilterMessageType
|
|
Integer32,
|
|
issL3FilterMessageCode
|
|
Integer32,
|
|
issL3FilterDstIpAddr
|
|
IpAddress,
|
|
issL3FilterSrcIpAddr
|
|
IpAddress,
|
|
issL3FilterDstIpAddrMask
|
|
IpAddress,
|
|
issL3FilterSrcIpAddrMask
|
|
IpAddress,
|
|
issL3FilterMinDstProtPort
|
|
Unsigned32,
|
|
issL3FilterMaxDstProtPort
|
|
Unsigned32,
|
|
issL3FilterMinSrcProtPort
|
|
Unsigned32,
|
|
issL3FilterMaxSrcProtPort
|
|
Unsigned32,
|
|
issL3FilterInPortList
|
|
PortList,
|
|
issL3FilterOutPortList
|
|
PortList,
|
|
issL3FilterAckBit
|
|
INTEGER,
|
|
issL3FilterRstBit
|
|
INTEGER,
|
|
issL3FilterTos
|
|
Integer32,
|
|
issL3FilterDscp
|
|
Integer32,
|
|
issL3FilterDirection
|
|
INTEGER,
|
|
issL3FilterAction
|
|
INTEGER,
|
|
issL3FilterMatchCount
|
|
Counter32,
|
|
issL3FilterStatus
|
|
RowStatus
|
|
}
|
|
|
|
issL3FilterNo OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"L3 Filter rule number.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3FilterEntry 1 }
|
|
|
|
issL3FilterPriority OBJECT-TYPE
|
|
SYNTAX Integer32 (1..255)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The priority of the filter can be used to decide which filter rule
|
|
is applicable when
|
|
--> the packet matches with more than one filter rules
|
|
--> All the filter rules result in 'allow'ing the packet
|
|
Higher value of 'L3 filter priority' implies a higher priority.
|
|
Usage of 'L3FilterPriority' is implementation dependant.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 1 }
|
|
::= { issL3FilterEntry 2 }
|
|
|
|
issL3FilterProtocol OBJECT-TYPE
|
|
SYNTAX Integer32 (0..255)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The type of protocol to be checked against the packet. The
|
|
default value is 255. If the value is 255, it means that the
|
|
protocol type can be anything and it will not be checked to
|
|
decide the action.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 255 }
|
|
::= { issL3FilterEntry 3 }
|
|
|
|
issL3FilterMessageType OBJECT-TYPE
|
|
SYNTAX Integer32 (0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The message type to be checked against the packet. If the
|
|
message type matches with the packet, then the packet will be
|
|
dropped / allowed based on the action set in issL3FilterAction.
|
|
The default value is 255. It means that message type is not
|
|
configured and need not be checked.
|
|
Generally the value zero is given as default. But here
|
|
zero can be an ICMP Type value. Hence 255 is given as the
|
|
default value.
|
|
Some ICMP message types are:
|
|
echoReply(0),
|
|
destinationUnreachable(3),
|
|
sourceQuench(4),
|
|
redirect(5),
|
|
echoRequest(8),
|
|
timeExceeded(11),
|
|
parameterProblem(12),
|
|
timestampRequest(13),
|
|
timestampReply(14),
|
|
informationRequest(15),
|
|
informationReply(16),
|
|
addressMaskRequest(17),
|
|
addressMaskReply (18),
|
|
noICMPType(255)
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 255 }
|
|
::= { issL3FilterEntry 4 }
|
|
|
|
issL3FilterMessageCode OBJECT-TYPE
|
|
SYNTAX Integer32 (0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The message code to be checked against the packet. If the
|
|
packet matches with the message code, then the packet will
|
|
be dropped / allowed based on the action set in issL3FilterAction.
|
|
The default value is 255. It means that message code is not
|
|
configured and need not be checked. Generally the value zero
|
|
will be given as default. But here, zero can be an ICMP Code
|
|
value. Hence 255 is given as the default value.
|
|
Some ICMP message codes are :
|
|
networkUnreachable(0),
|
|
hostUnreachable(1),
|
|
protocolUnreachable(2),
|
|
portUnreachable(3),
|
|
fragmentNeed(4),
|
|
sourceRouteFail(5),
|
|
destNetworkUnknown(6),
|
|
destHostUnknown(7),
|
|
srcHostIsolated(8),
|
|
destNetworkAdminProhibited(9),
|
|
destHostAdminProhibited(10),
|
|
networkUnreachableTOS(11),
|
|
hostUnreachableTOS(12),
|
|
noICMPCode(255)
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 255 }
|
|
::= { issL3FilterEntry 5 }
|
|
|
|
issL3FilterDstIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Destination IP address to be matched with the packet.
|
|
This object is valid only if the 'issFilterType' is 'l3filter'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { '00000000'h }
|
|
::= { issL3FilterEntry 6 }
|
|
|
|
issL3FilterSrcIpAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Source IP address to be matched with the packet.
|
|
This object is valid only if the 'issFilterType' is 'l3filter'
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { '00000000'h }
|
|
::= { issL3FilterEntry 7 }
|
|
|
|
issL3FilterDstIpAddrMask OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The IP subnet mask for Destination IP address.
|
|
This object is valid only if the 'issFilterType' is 'l3filter'
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 'FFFFFFFF'h }
|
|
::= { issL3FilterEntry 8 }
|
|
|
|
issL3FilterSrcIpAddrMask OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The IP subnet mask for Source IP address.
|
|
This object is valid only if the 'issFilterType' is 'l3filter'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 'FFFFFFFF'h }
|
|
::= { issL3FilterEntry 9 }
|
|
|
|
issL3FilterMinDstProtPort OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The minimum port in the destination port range. Please note
|
|
these ports are the TCP / UDP ports.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 0 }
|
|
::= { issL3FilterEntry 10 }
|
|
|
|
issL3FilterMaxDstProtPort OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The maximum port in the destination port range. Please note
|
|
these ports are the TCP / UDP ports.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 65535 }
|
|
::= { issL3FilterEntry 11 }
|
|
|
|
issL3FilterMinSrcProtPort OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The minimum port in the source port range. Please note
|
|
these ports are the TCP / UDP ports.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 0 }
|
|
::= { issL3FilterEntry 12 }
|
|
|
|
issL3FilterMaxSrcProtPort OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The maximum port in the source port range. Please note
|
|
these ports are the TCP / UDP ports.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { 65535 }
|
|
::= { issL3FilterEntry 13 }
|
|
|
|
issL3FilterInPortList OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the complete set of ports over which if the packet arrives
|
|
this filter rule will be applicable.
|
|
If the incoming port list is '0', the filter rule is applicable for all the
|
|
incoming ports.
|
|
By default inport list is maintained as '0'.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3FilterEntry 14 }
|
|
|
|
issL3FilterOutPortList OBJECT-TYPE
|
|
SYNTAX PortList
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the complete set of ports over which if the packet goes out,
|
|
this filter rule will be applicable.
|
|
If the outgoing port list is '0',the filter rule is applicable for all the
|
|
outgoing packets in all ports.
|
|
By default outport list is maintained as '0'
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3FilterEntry 15 }
|
|
|
|
issL3FilterAckBit OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
establish(1),
|
|
notEstablish(2),
|
|
any(3)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The TCP ACK bit to be checked against the packet. The default
|
|
value is 'any'(3). It means that ACK bit will not be checked
|
|
to decide the action.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { any }
|
|
::= { issL3FilterEntry 16 }
|
|
|
|
issL3FilterRstBit OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
set(1),
|
|
notSet(2),
|
|
any(3)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The TCP RST bit to be checked against the packet. The default
|
|
value is 'any'(3). It means that RST bit will not be checked to
|
|
decide the action.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { any }
|
|
::= { issL3FilterEntry 17 }
|
|
|
|
issL3FilterTos OBJECT-TYPE
|
|
SYNTAX Integer32 (-1..7)
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The IP TOS bit to be checked against the packet. This is a
|
|
single byte integer of which the last three bits (least
|
|
significant bits) indicate Delay, Throughput and Reliability
|
|
i.e 'uuuuudtr', u-unused, d-delay, t-throughput, r-reliability.
|
|
For example '6' indicates low delay and high throughput.
|
|
A value of '-1' means, the Tos Field becomes dont care
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { -1 }
|
|
::= { issL3FilterEntry 18 }
|
|
|
|
issL3FilterDscp OBJECT-TYPE
|
|
SYNTAX Integer32 (-1..63)
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
" The IP Dscp value to be checked against the packet.
|
|
A value of '-1' means, the Dscp Field becomes dont care.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { -1 }
|
|
::= { issL3FilterEntry 19 }
|
|
|
|
issL3FilterDirection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
in (1),
|
|
out(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the direction of this filter to be applied. By Default the
|
|
filter will be applied on ingress direction.
|
|
When the direction of this filter is 'in', It is applied on specified
|
|
ports of the issL3FilterInPortList.
|
|
When the direction of this filter is 'out', It is applied on specified
|
|
ports of the issL3FilterOutPortList.This object is deprecated and
|
|
the corresponding functionality is met with issL3Filter objects in
|
|
fsissext.mib."
|
|
DEFVAL { in }
|
|
::= { issL3FilterEntry 20 }
|
|
|
|
issL3FilterAction OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
allow (1),
|
|
drop (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Specifies the action to be taken on the packet if the filter
|
|
rule matches.
|
|
If the action is 'allow', the packet will be sent to the
|
|
ports in 'out port list'. If the out port list is '0',
|
|
the port over which the packet is to be switched will be decided
|
|
based on further processing on the packet.
|
|
If the action is 'drop', the packet will be discardedThis object is
|
|
deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
DEFVAL { allow }
|
|
::= { issL3FilterEntry 21 }
|
|
|
|
issL3FilterMatchCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"Number of times this filter is matched.
|
|
This object is deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3FilterEntry 22 }
|
|
|
|
issL3FilterStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This object indicates the status of this entry. An entry is
|
|
created in this table when this object is SET to 'createAndWait'.
|
|
The entry in this table is used when the status of this object
|
|
is SET 'active'. The entry in this table is not used when this
|
|
object is SET 'notInService'. An entry created in this table is
|
|
be deleted when this object is SET 'destroy.This object is
|
|
deprecated and the corresponding functionality is
|
|
met with issL3Filter objects in fsissext.mib."
|
|
::= { issL3FilterEntry 23 }
|
|
|
|
|
|
-- ------------------------------------------------------------------
|
|
------------------------------------------------------------------
|
|
-- Layer 4 Switching
|
|
|
|
|
|
issL4SwitchingFilterTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssL4SwitchingFilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
" A table to L4 Switching rules in the system.
|
|
"
|
|
::= { issL4Switching 1 }
|
|
|
|
issL4SwitchingFilterEntry OBJECT-TYPE
|
|
SYNTAX IssL4SwitchingFilterEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
" Each entry in this table is a L4 Switching rule.
|
|
Index to the table is L4 filter number. "
|
|
INDEX { issL4SwitchingFilterNo}
|
|
::= { issL4SwitchingFilterTable 1 }
|
|
|
|
IssL4SwitchingFilterEntry ::=
|
|
SEQUENCE {
|
|
issL4SwitchingFilterNo
|
|
Integer32,
|
|
issL4SwitchingProtocol
|
|
Integer32,
|
|
issL4SwitchingPortNo
|
|
Unsigned32,
|
|
issL4SwitchingCopyToPort
|
|
Integer32,
|
|
issL4SwitchingFilterStatus
|
|
RowStatus
|
|
}
|
|
|
|
issL4SwitchingFilterNo OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"L4 Switching Filter rule number."
|
|
::= { issL4SwitchingFilterEntry 1 }
|
|
|
|
|
|
issL4SwitchingProtocol OBJECT-TYPE
|
|
SYNTAX Integer32 (0..255)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The type of protocol to be checked against the packet. The
|
|
default value is 255. If the value is 255, it means that the
|
|
protocol type can be anything and it will not be checked to
|
|
decide the action. "
|
|
DEFVAL { 255 }
|
|
::= { issL4SwitchingFilterEntry 2 }
|
|
|
|
|
|
issL4SwitchingPortNo OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Layer 4 port no. Please note
|
|
these ports are the TCP / UDP ports."
|
|
DEFVAL { 0 }
|
|
::= { issL4SwitchingFilterEntry 3 }
|
|
|
|
issL4SwitchingCopyToPort OBJECT-TYPE
|
|
SYNTAX Integer32(0..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is Port to which the packet would be switched"
|
|
|
|
::= { issL4SwitchingFilterEntry 4 }
|
|
|
|
issL4SwitchingFilterStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the status of this entry."
|
|
|
|
::= { issL4SwitchingFilterEntry 5 }
|
|
|
|
-- issModule Group BEGINS
|
|
|
|
issModuleTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssModuleEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
" A table for triggering Graceful shutdown and Start"
|
|
::= { issModule 1 }
|
|
|
|
issModuleEntry OBJECT-TYPE
|
|
SYNTAX IssModuleEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
" Each entry in this table corresponding to one protocol"
|
|
INDEX { issModuleId }
|
|
::= { issModuleTable 1 }
|
|
|
|
IssModuleEntry ::=
|
|
SEQUENCE {
|
|
issModuleId
|
|
Integer32,
|
|
issModuleSystemControl
|
|
INTEGER
|
|
}
|
|
|
|
issModuleId OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the ID of the protocol.
|
|
Following IDs are supported.
|
|
1. OSPF
|
|
2. OSPFV3
|
|
3. BGP
|
|
4. ISIS
|
|
5. RSVPTE
|
|
6. LDP "
|
|
|
|
::= { issModuleEntry 1 }
|
|
|
|
issModuleSystemControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
idle (0),
|
|
shutdown (1), -- shutdown the process
|
|
start (2) -- start the process
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object shuts and starts the process"
|
|
DEFVAL { start }
|
|
::= { issModuleEntry 2 }
|
|
|
|
-- issModule Group ENDS
|
|
|
|
-- ------------------------------------------------------------------
|
|
--- FAN Table
|
|
issSwitchFanTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF IssSwitchFanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Table containing the Fan information."
|
|
::= { issSwitchFan 1 }
|
|
|
|
issSwitchFanEntry OBJECT-TYPE
|
|
SYNTAX IssSwitchFanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates information related to fan status of
|
|
the switch."
|
|
INDEX { issSwitchFanIndex }
|
|
::= { issSwitchFanTable 1 }
|
|
|
|
IssSwitchFanEntry ::=
|
|
SEQUENCE {
|
|
issSwitchFanIndex Integer32,
|
|
issSwitchFanStatus INTEGER
|
|
}
|
|
|
|
issSwitchFanIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..5)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the fan number in the switch"
|
|
::= { issSwitchFanEntry 1 }
|
|
|
|
issSwitchFanStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
up(1),
|
|
down(2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the fan status of the switch."
|
|
::= { issSwitchFanEntry 2 }
|
|
|
|
-----------------------------------------------------------------------
|
|
-- Trap Objects
|
|
|
|
issMsrFailedOid OBJECT-TYPE
|
|
SYNTAX OBJECT IDENTIFIER
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the OID for which updation failure has occured at MSR"
|
|
::= { issSystemTrap 1 }
|
|
|
|
issMsrFailedValue OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the value of corresponding OID for which updation failure
|
|
has occured at MSR"
|
|
::= { issSystemTrap 2 }
|
|
|
|
-- Audit Trap Objects
|
|
|
|
issAuditTrapEvent OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
openFailed(1),
|
|
writeFailed(2),
|
|
sizeExceeded(3),
|
|
sizeThresholdHit(4)
|
|
}
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
" openFailed - Open operation on Audit File failed.
|
|
writeFailed - Write operation on Audit File failed.
|
|
sizeExceeded - Audit File Size exceeded.
|
|
sizeThresholdHit - Audit Log Size Hit the threshold value."
|
|
::= { issAuditTrap 1 }
|
|
|
|
issAuditTrapEventTime OBJECT-TYPE
|
|
SYNTAX DisplayString(SIZE(24))
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the date and time at which fsAuditTrapEvent
|
|
was performed."
|
|
::= { issAuditTrap 2 }
|
|
|
|
issAuditTrapFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Audit File name in the trap message."
|
|
::= { issAuditTrap 3 }
|
|
|
|
-- Log Trap Objects
|
|
|
|
issLogTrapEvent OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
openFailed(1),
|
|
writeFailed(2),
|
|
sizeExceeded(3),
|
|
sizeThresholdHit(4)
|
|
}
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
" openFailed - Open operation on Log File failed.
|
|
writeFailed - Write operation on Log File failed.
|
|
sizeExceeded - Log File Size exceeded.
|
|
sizeThresholdHit - Log Size Hit the threshold value."
|
|
::= { issLogTrap 1 }
|
|
|
|
issLogTrapEventTime OBJECT-TYPE
|
|
SYNTAX DisplayString(SIZE(24))
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the date and time at which fsLogTrapEvent
|
|
was performed."
|
|
::= { issLogTrap 2 }
|
|
|
|
issLogTrapFileName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(1..128))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Log File name in the trap message."
|
|
::= { issLogTrap 3 }
|
|
|
|
-- ------------------------------------------------------------------
|
|
-- Iss Notifications
|
|
|
|
issTrapConfigRestore NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issConfigRestoreStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This trap signifies the successful restoration of
|
|
the saved configuration"
|
|
::= { issNotifications 1 }
|
|
|
|
issMsrUpdateEventFail NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issMsrFailedOid,
|
|
issMsrFailedValue
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An MsrUpdateEventFail notification is sent when there is some
|
|
failure in configuration change event received from SNMP Agent.
|
|
issMsrFailedOid indicates the OID for which configuration change
|
|
event has failed.
|
|
issMsrFailedValue indicates the value of the corresponding OID for
|
|
which configuration change event failure has occured."
|
|
::= { issNotifications 2 }
|
|
|
|
-- AUDIT TRAP MESSAGE
|
|
issAuditTrapMessage NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issAuditTrapEvent,
|
|
issAuditTrapEventTime,
|
|
issAuditTrapFileName
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This trap notifies the erros on
|
|
Audit file."
|
|
::= { issNotifications 3 }
|
|
|
|
issTrapTemperature NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchMinThresholdTemperature,
|
|
issSwitchMaxThresholdTemperature,
|
|
issSwitchCurrentTemperature
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when the current
|
|
temperature rises above or drops below the threshold."
|
|
::= { issNotifications 4 }
|
|
|
|
issTrapCPUThreshold NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchMaxCPUThreshold,
|
|
issSwitchCurrentCPUThreshold
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when CPU load exceeds
|
|
the threshold value"
|
|
::= { issNotifications 5 }
|
|
|
|
issTrapPowerSupply NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchPowerSurge,
|
|
issSwitchPowerFailure,
|
|
issSwitchCurrentPowerSupply
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when the current
|
|
voltage drops below or exceeds the threshold value"
|
|
::= { issNotifications 6 }
|
|
|
|
issTrapRAMUsage NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchMaxRAMUsage,
|
|
issSwitchCurrentRAMUsage
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when the RAM usage crosses
|
|
the threshold percentage."
|
|
::= { issNotifications 7 }
|
|
|
|
issTrapFlashUsage NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchMaxFlashUsage,
|
|
issSwitchCurrentFlashUsage
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when the flash
|
|
usage crosses the threshold."
|
|
::= { issNotifications 8 }
|
|
|
|
issTrapFanStatus NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issSwitchFanIndex,
|
|
issSwitchFanStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is sent when the fan status is changed
|
|
from down state to up state or vice versa."
|
|
::= { issNotifications 9 }
|
|
|
|
-- LOG TRAP MESSAGE
|
|
issLogTrapMessage NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issLogTrapEvent,
|
|
issLogTrapEventTime,
|
|
issLogTrapFileName
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This trap notifies the erros on
|
|
System Log file."
|
|
::= { issNotifications 10 }
|
|
|
|
-- PAUSE FLOOD SNMP TRAP MESSAGE
|
|
issPauseFloodSnmpTrapMessage NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
issPortCtrlPauseFloodStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to notify the pause flood condition when the pause
|
|
flood mode is 'enabled'"
|
|
::= { issNotifications 11 }
|
|
|
|
issAclProvisionMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
immediate(1),
|
|
consolidated(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The MIB object issAclProvisionMode is used to configure the
|
|
mode for provisioning active Filter Rules to the hardware.
|
|
This object takes values immediate/consolidated. When this
|
|
object is set to immediate, active ACL rules are programmed
|
|
to hardware immediately. This is the default mode. In this
|
|
mode, the sequence of configuration determines the order of
|
|
provisioning the Filter rule to the hardware.
|
|
When this object is set to consolidated, active Filter Rules
|
|
are provisioned whenever a commit is triggered using MIB
|
|
object issAclTriggerCommit. In the consolidated mode, the
|
|
Filter rules are programmed/re-programmed to hardware in
|
|
the order of configured priority."
|
|
DEFVAL { immediate }
|
|
::= { issAclNp 1 }
|
|
|
|
|
|
issAclTriggerCommit OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
false(0),
|
|
true(1)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The MIB object issAclTriggerCommit takes values true(1)/false (0).
|
|
A SET on this object ( only true is allowed) triggers the
|
|
programming of active ACL entries to the device based on
|
|
configured priority.After completion of the operation, this MIB object
|
|
is reset to false( 0) .This object is applicable only when the MIB
|
|
object issAclProvisionMode is set to ' consolidated.
|
|
A set on this object will impact the existing traffic flow as existing
|
|
Filter entries are deleted
|
|
and re-programmed to hardware based on configured priority.
|
|
Filter entries that are associated with quality-of-service configurations
|
|
will also be impacted when this object
|
|
triggers the re-programming of the active ACL entries to the hardware.
|
|
The administrator needs to ensure that corresponding Filter entries are
|
|
de-provisioned before triggering commit."
|
|
DEFVAL { false }
|
|
::= { issAclNp 2 }
|
|
|
|
-- Traffic Control Group ------------------------------------------ --
|
|
|
|
issAclTrafficSeperationCtrl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
systemdefault (1),
|
|
userconfig (2),
|
|
none(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object provides control to administrator, to have system default or
|
|
user defined ACL/QoS rules to carry control traffic to CPU.
|
|
|
|
system-default: ACL/QoS rules for all the control packets will be
|
|
automatically installed by the ISS software at system init time.Either a
|
|
'switch-and-copy-to-cpu'filter (or) 'drop-and-copy-to-cpu' filter will be
|
|
installed, as appropriate, for getting the control packets to CPU, for
|
|
processing. Each ACL rule will be associated with class-map, meter and
|
|
policy map with protocol ID, and CPU queue number
|
|
|
|
user-config: The ACL/QoS rules for receiving all the control packets to
|
|
CPU for processing, will NOT be automatically installed by the the ISS
|
|
software.The administrator is expected to install required rules for the
|
|
control packets as requried.
|
|
|
|
none: ACL/QoS rules for all the control packets will be automatically
|
|
installed by the ISS software at system init time.Either a 'switch-and-co
|
|
py-to-cpu'filter (or) 'drop-and-copy-to-cpu' filter will be installed,
|
|
as appropriate, for getting the control packets to CPU, for processing.
|
|
Default mode is none
|
|
|
|
If the configuration is changed from 'systemdefault' to 'userconfig'
|
|
option, then all the default ACL/QoS rules for carrying protocol control
|
|
packets to CPU are removed.Then user has to install the specific ACL/QoS
|
|
rules, to carry the intended control packets to CPU for the processing.
|
|
|
|
If the configuration is changed from 'userconfig' to 'systemdefault',
|
|
all the default ACL/QoS rules are installed. Already existing(if any)
|
|
user configured ACL rules in the system are not removed.
|
|
|
|
If the configuration is changed from 'none' to 'systemdefault'
|
|
option, then all the default ACL filters for carrying protocol control
|
|
packets to CPU are removed and new set of filters will be installed.
|
|
Each filter will be associated with Qos rules.
|
|
|
|
If the configuration is changed from 'none' to 'userconfig'
|
|
option, then all the default ACL filters for carrying protocol control
|
|
packets to CPU are removed.Then user has to install the specific ACL/QoS
|
|
rules, to carry the intended control packets to CPU for the processing.
|
|
|
|
If the configuration is changed from 'userconfig' to 'none'
|
|
all the default ACL filters are installed. Already existing(if any)
|
|
user configured ACL rules in the system are not removed.
|
|
|
|
Above three options can be configured during system runtime."
|
|
|
|
DEFVAL { none }
|
|
::= { issAclTrafficControl 1 }
|
|
|
|
--ISShealthchk--
|
|
|
|
issHealthChkStatus OBJECT-TYPE
|
|
SYNTAX INTEGER { upAndRunning(1),
|
|
downNonRecoverableErr(2),
|
|
upRecoverableRuntimeErr(3) }
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"upAndRunning(1), This status indicates that ISS is up and running
|
|
and carrying out its job smoothly.
|
|
|
|
downNonRecoverableErr(2), This indicates that the health status of ISS is down
|
|
due to occurence of some non-recoverable error.
|
|
|
|
upRecoverableRuntimeErr(3), This indicates that the health status of ISS is up
|
|
but indicates the occurence of a runtime error that is recoverable."
|
|
|
|
|
|
::= { issHealthCheckGroup 1 }
|
|
|
|
issHealthChkErrorReason OBJECT-TYPE
|
|
SYNTAX INTEGER { nonRecovTaskInitializationFailure(1),
|
|
nonRecovInsufficientStartupMemory(2),
|
|
recovCruBuffExhausted(3),
|
|
recovConfigRestoreFailed(4),
|
|
recovProtocolMemPoolExhausted(5) }
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When the MIB object 'issHealthChkStatus' indicates health as down, this object provides the
|
|
reason for errors encountered.
|
|
|
|
nonRecovTaskInitializationFailure(1), Indicates the occurence of non-recoverable failure during
|
|
Task initialization.
|
|
|
|
nonRecovInsufficientStartupMemory(2), Indicates that there is insufficient memory for successful
|
|
startup. This error is non-recoverable and requires sufficient memory to be available in the system
|
|
for successful ISS startup.
|
|
|
|
recovCruBuffExhausted(3), Indicates that CRU Buffer Exhausted.
|
|
|
|
recovConfigRestoreFailed(4), Indicates that config-restore failed for ISS. This is a recoverable error.
|
|
|
|
recovProtocolMemPoolExhausted(5), Indicates that a mem-pool associated with a specific module in ISS has
|
|
drained out. This error may affect the functioning of the specific protocol alone and is treated as
|
|
a recoverable error.
|
|
|
|
By default issHealthChkErrorReason is 0."
|
|
|
|
|
|
::= { issHealthCheckGroup 2 }
|
|
|
|
issHealthChkMemAllocErrPoolId OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object retrieves the mem-pool identifier for which memory allocation
|
|
failure was encountered at run-time.This object will get updated when
|
|
MIB object fsISSHealthChkErrorReason takes value of recovProtocolMemPoolExhausted (5)."
|
|
|
|
::= { issHealthCheckGroup 3}
|
|
|
|
issHealthChkConfigRestoreStatus OBJECT-TYPE
|
|
SYNTAX INTEGER { configRestoreSuccess(1),
|
|
configRestoreFailed(2),
|
|
configRestoreInProgress(3),
|
|
configRestoreDefault(4) }
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"configRestoreSuccess(1), Indicates that configuration restore operation
|
|
was successfully done.
|
|
|
|
configRestoreFailed(2),Indicates that configuration restoration was unsuccessful.
|
|
|
|
configRestoreInProgress(3), Indicates that configuration restore operation is in-progress for ISS.
|
|
|
|
configRestoreDefault(4), Indicates the absence of config-restore file (iss.conf)
|
|
and that ISS was started with default values.
|
|
|
|
By default issHealthChkConfigRestoreStatus is 4."
|
|
|
|
|
|
::= { issHealthCheckGroup 4}
|
|
|
|
issHealthChkClearCtr OBJECT-TYPE
|
|
SYNTAX BITS{
|
|
bgp(1),
|
|
ospf(2),
|
|
rip(3),
|
|
rip6(4),
|
|
ospf3(5),
|
|
ipv4(6),
|
|
ipv6(7)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object clears the counters
|
|
associated with the following protocols -
|
|
BGP, OSPFv2, RIPv2/ng, OSPFv3, RTMv4/v6, ARP/ND, NETIP(v4/v6)
|
|
All the bit is set as 1, it clears the specified protocol counters.
|
|
bgp(1) When this bit is set,clears bgp protocol counters.
|
|
ospf(2) When this bit is set,clears ospf protocol counters.
|
|
rip(3) When this bit is set,clears rip protocol counters.
|
|
rip6(4) When this bit is set,clears rip6 protocol counters.
|
|
ospf3(5) When this bit is set,clears ospf3 protocol counters.
|
|
ipv4(6) When this bit is set,clears ipv4 protocol counters.
|
|
ipv6(7) When this bit is set,clears ipv6 protocol counters."
|
|
|
|
::= { issHealthCheckGroup 5}
|
|
|
|
|
|
|
|
|
|
END
|