mibs/MIBS/ADSL2-LINE-TC-MIB
2023-12-05 12:25:34 +01:00

729 lines
31 KiB
Plaintext

ADSL2-LINE-TC-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
transmission
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC;
adsl2TCMIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z"
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO
"WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: P.O. Box 37324
Raleigh NC 27627-732
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-Chair & Co-editor:
Menachem Dodge
ECI Telecom Ltd.
Postal: 30 Hasivim St.
Petach Tikva 49517,
Israel.
Email: mbdodge@ieee.org
Phone: +972 3 926 8421
Co-editor: Moti Morgenstern
ECI Telecom Ltd.
Postal: 30 Hasivim St.
Petach Tikva 49517,
Israel.
Email: moti.morgenstern@ecitele.com
Phone: +972 3 926 6258
Co-editor: Scott Baillie
NEC Australia
Postal: 649-655 Springvale Road,
Mulgrave, Victoria 3170,
Australia.
Email: scott.baillie@nec.com.au
Phone: +61 3 9264 3986
Co-editor: Umberto Bonollo
NEC Australia
Postal: 649-655 Springvale Road,
Mulgrave, Victoria 3170,
Australia.
Email: umberto.bonollo@nec.com.au
Phone: +61 3 9264 3385"
DESCRIPTION
"This MIB Module provides Textual Conventions to be
used by the ADSL2-LINE-MIB module for the purpose of
managing ADSL, ADSL2, and ADSL2+ lines.
Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC 4706: see the RFC itself for
full legal notices."
REVISION "200610040000Z"
DESCRIPTION
"Initial version, published as RFC 4706."
::= { transmission 238 2 }
-- adsl2MIB 2
--
-- ----------------------------------------------
-- Textual Conventions --
-- ----------------------------------------------
Adsl2Unit ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a transceiver as being either an ATU-C or
an ATU-R. An ADSL line consists of two transceivers, an ATU-C
and an ATU-R. Attributes with this syntax reference the two
sides of a line. Specified as an INTEGER, the two values
are:
atuc(1) -- Central office ADSL terminal unit (ATU-C).
atur(2) -- Remote ADSL terminal unit (ATU-R)."
SYNTAX INTEGER {
atuc(1),
atur(2)
}
Adsl2Direction ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies the direction of a band as being
either upstream or downstream. Specified as an INTEGER,
the two values are:
upstream(1), and
downstream(2)."
SYNTAX INTEGER {
upstream(1),
downstream(2)
}
Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A set of ADSL2 line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate
and Lite/splitterless, respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1,
wide U/S (F)
Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2,
narrow U/S(F)
Bit 36 : G.992.3 Annex L POTS overlapped, mode 3,
wide U/S (F)
Bit 37 : G.992.3 Annex L POTS overlapped, mode 4,
narrow U/S (F)
Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
Bit 39 : G.992.3 Annex M POTS overlapped (F)
Bit 40 : G.992.5 POTS non-overlapped (F)
Bit 41 : G.992.5 POTS overlapped (F)
Bit 42 : G.992.5 ISDN non-overlapped (F)
Bit 43 : G.992.5 ISDN overlapped (F)
Bit 44-45: Reserved
Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
Bit 51 : G.992.5 Annex M POTS overlapped (F)
Bit 52-55: Reserved"
SYNTAX BITS {
ansit1413(0),
etsi(1),
g9921PotsNonOverlapped(2),
g9921PotsOverlapped(3),
g9921IsdnNonOverlapped(4),
g9921isdnOverlapped(5),
g9921tcmIsdnNonOverlapped(6),
g9921tcmIsdnOverlapped(7),
g9922potsNonOverlapped(8),
g9922potsOverlapped(9),
g9922tcmIsdnNonOverlapped(10),
g9922tcmIsdnOverlapped(11),
g9921tcmIsdnSymmetric(12),
reserved1(13),
reserved2(14),
reserved3(15),
reserved4(16),
reserved5(17),
g9923PotsNonOverlapped(18),
g9923PotsOverlapped(19),
g9923IsdnNonOverlapped(20),
g9923isdnOverlapped(21),
reserved6(22),
reserved7(23),
g9924potsNonOverlapped(24),
g9924potsOverlapped(25),
reserved8(26),
reserved9(27),
g9923AnnexIAllDigNonOverlapped(28),
g9923AnnexIAllDigOverlapped(29),
g9923AnnexJAllDigNonOverlapped(30),
g9923AnnexJAllDigOverlapped(31),
g9924AnnexIAllDigNonOverlapped(32),
g9924AnnexIAllDigOverlapped(33),
g9923AnnexLMode1NonOverlapped(34),
g9923AnnexLMode2NonOverlapped(35),
g9923AnnexLMode3Overlapped(36),
g9923AnnexLMode4Overlapped(37),
g9923AnnexMPotsNonOverlapped(38),
g9923AnnexMPotsOverlapped(39),
g9925PotsNonOverlapped(40),
g9925PotsOverlapped(41),
g9925IsdnNonOverlapped(42),
g9925isdnOverlapped(43),
reserved10(44),
reserved11(45),
g9925AnnexIAllDigNonOverlapped(46),
g9925AnnexIAllDigOverlapped(47),
g9925AnnexJAllDigNonOverlapped(48),
g9925AnnexJAllDigOverlapped(49),
g9925AnnexMPotsNonOverlapped(50),
g9925AnnexMPotsOverlapped(51),
reserved12(52),
reserved13(53),
reserved14(54),
reserved15(55)
}
Adsl2RaMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the rate adaptation behavior for the line.
The three possible behaviors are:
manual(1) - No Rate-Adaptation. The initialization
process attempts to synchronize to a
specified rate.
raInit(2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate
between minimum and maximum specified values.
dynamicRa(3) - Dynamic Rate-Adaptation during initialization
process as well as during SHOWTIME."
SYNTAX INTEGER {
manual(1),
raInit(2),
dynamicRa(3)
}
Adsl2InitResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the result of a full initialization attempt; the
six possible result values are:
noFail(0) - Successful initialization.
configError(1) - Configuration failure.
configNotFeasible(2) - Configuration details not supported.
commFail(3) - Communication failure.
noPeerAtu(4) - Peer ATU not detected.
otherCause(5) - Other initialization failure reason.
The values used are as defined in ITU-T G.997.1,
paragraph 7.5.1.3"
SYNTAX INTEGER {
noFail(0),
configError(1),
configNotFeasible(2),
commFail(3),
noPeerAtu(4),
otherCause(5)
}
Adsl2OperationModes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The ADSL2 management model specified includes an ADSL Mode
attribute that identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The
following classes of ADSL operating mode are defined.
The notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively:
+-------+--------------------------------------------------+
| Value | ADSL operation mode description |
+-------+--------------------------------------------------+
1 - The default/generic PSD configuration. Default
configuration will be used when no other matching
mode-specific configuration can be found.
2 - ADSL family. The attributes included in the Mode-
Specific PSD Configuration are irrelevant for
ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it
is possible to map those modes to this generic
class.
3-7 - Unused. Reserved for future ITU-T specification.
8 - G.992.3 POTS non-overlapped (F)
9 - G.992.3 POTS overlapped (F)
10 - G.992.3 ISDN non-overlapped (F)
11 - G.992.3 ISDN overlapped (F)
12-13 - Unused. Reserved for future ITU-T specification.
14 - G.992.4 POTS non-overlapped (L)
15 - G.992.4 POTS overlapped (L)
16-17 - Unused. Reserved for future ITU-T specification.
18 - G.992.3 Annex I All-Digital non-overlapped (F)
19 - G.992.3 Annex I All-Digital overlapped (F)
20 - G.992.3 Annex J All-Digital non-overlapped (F)
21 - G.992.3 Annex J All-Digital overlapped (F)
22 - G.992.4 Annex I All-Digital non-overlapped (L)
23 - G.992.4 Annex I All-Digital overlapped (L)
24 - G.992.3 Annex L POTS non-overlapped, mode 1,
wide U/S (F)
25 - G.992.3 Annex L POTS non-overlapped, mode 2,
narrow U/S(F)
26 - G.992.3 Annex L POTS overlapped, mode 3,
wide U/S (F)
27 - G.992.3 Annex L POTS overlapped, mode 4,
narrow U/S (F)
28 - G.992.3 Annex M POTS non-overlapped (F)
29 - G.992.3 Annex M POTS overlapped (F)
30 - G.992.5 POTS non-overlapped (F)
31 - G.992.5 POTS overlapped (F)
32 - G.992.5 ISDN non-overlapped (F)
33 - G.992.5 ISDN overlapped (F)
34-35 - Unused. Reserved for future ITU-T specification.
36 - G.992.5 Annex I All-Digital non-overlapped (F)
37 - G.992.5 Annex I All-Digital overlapped (F)
38 - G.992.5 Annex J All-Digital non-overlapped (F)
39 - G.992.5 Annex J All-Digital overlapped (F)
40 - G.992.5 Annex M POTS non-overlapped (F)
41 - G.992.5 Annex M POTS overlapped (F)"
SYNTAX INTEGER {
defMode(1),
adsl(2),
g9923PotsNonOverlapped(8),
g9923PotsOverlapped(9),
g9923IsdnNonOverlapped(10),
g9923isdnOverlapped(11),
g9924potsNonOverlapped(14),
g9924potsOverlapped(15),
g9923AnnexIAllDigNonOverlapped(18),
g9923AnnexIAllDigOverlapped(19),
g9923AnnexJAllDigNonOverlapped(20),
g9923AnnexJAllDigOverlapped(21),
g9924AnnexIAllDigNonOverlapped(22),
g9924AnnexIAllDigOverlapped(23),
g9923AnnexLMode1NonOverlapped(24),
g9923AnnexLMode2NonOverlapped(25),
g9923AnnexLMode3Overlapped(26),
g9923AnnexLMode4Overlapped(27),
g9923AnnexMPotsNonOverlapped(28),
g9923AnnexMPotsOverlapped(29),
g9925PotsNonOverlapped(30),
g9925PotsOverlapped(31),
g9925IsdnNonOverlapped(32),
g9925isdnOverlapped(33),
g9925AnnexIAllDigNonOverlapped(36),
g9925AnnexIAllDigOverlapped(37),
g9925AnnexJAllDigNonOverlapped(38),
g9925AnnexJAllDigOverlapped(39),
g9925AnnexMPotsNonOverlapped(40),
g9925AnnexMPotsOverlapped(41)
}
Adsl2PowerMngState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax uniquely identify each power
management state defined for the ADSL/ADSL2 or ADSL2+ link.
The possible values are:
l0(1) - L0 - Full power management state.
l1(2) - L1 - Low power management state (for G.992.2).
l2(3) - L2 - Low power management state (for G.992.3,
G.992.4, and G.992.5).
l3(4) - L3 - Idle power management state."
SYNTAX INTEGER {
l0(1),
l1(2),
l2(3),
l3(4)
}
Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the desired power management state for the
ADSL/ADSL2 or ADSL2+ link:
l3toL0(0) - Perform a transition from L3 to L0
(Full power management state).
l0toL2(2) - Perform a transition from L0 to L2
(Low power management state).
l0orL2toL3(3) - Perform a transition into L3 (Idle
power management state).
The values used are as defined in ITU-T G.997.1,
paragraph 7.3.1.1.3"
SYNTAX INTEGER {
l3toL0(0),
l0toL2(2),
l0orL2toL3(3)
}
Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the power modes/states into which the ATU-C or
ATU-R may autonomously transit.
It is a BITS structure that allows control of the following
transit options:
allowTransitionsToIdle(0) - XTU may autonomously transit
to idle (L3) state.
allowTransitionsToLowPower(1) - XTU may autonomously transit
to low-power (L2) state."
SYNTAX BITS {
allowTransitionsToIdle(0),
allowTransitionsToLowPower(1)
}
Adsl2LineLdsf ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that control the Loop Diagnostic mode for the ADSL/ADSL2 or
ADSL2+ link. The possible values are:
inhibit(0) - Inhibit Loop Diagnostic mode.
force(1) - Force/Initiate Loop Diagnostic mode.
The values used are as defined in ITU-T G.997.1,
paragraph 7.3.1.1.8"
SYNTAX INTEGER {
inhibit(0),
force(1)
}
Adsl2LdsfResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Possible failure reasons associated with performing
a Dual Ended Loop Test (DELT) on a DSL line.
Possible values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
SYNTAX INTEGER {
none(1),
success(2),
inProgress(3),
unsupported(4),
cannotRun(5),
aborted(6),
failed(7),
illegalMode(8),
adminUp(9),
tableFull(10),
noResources(11)
}
Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the minimum-length impulse noise protection
(INP) in terms of number of symbols. The possible values are:
noProtection (i.e., INP not required), halfSymbol (i.e., INP
length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
SYNTAX INTEGER {
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5),
fourSymbols(6),
fiveSymbols(7),
sixSymbols(8),
sevenSymbols(9),
eightSymbols(10),
nineSymbols(11),
tenSymbols(12),
elevenSymbols(13),
twelveSymbols(14),
thirteeSymbols(15),
fourteenSymbols(16),
fifteenSymbols(17),
sixteenSymbols(18)
}
Adsl2MaxBer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the maximum Bit Error Rate (BER).
The possible values are:
eminus3(1) - Maximum BER=E^-3
eminus5(2) - Maximum BER=E^-5
eminus7(3) - Maximum BER=E^-7"
SYNTAX INTEGER {
eminus3(1),
eminus5(2),
eminus7(3)
}
Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE (0..64))
Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 64 bits in this OCTET
STRING array represents the corresponding bin
in the upstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE (0..8))
Adsl2RfiDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is part of a notch
filter."
SYNTAX OCTET STRING (SIZE (0..64))
Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE (0..96))
Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
4 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE (0..12))
Adsl2Tssi ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 transmit spectrum shaping (TSSi) breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the shaping parameter at the breakpoint. It
is a value from 0 to 127 (units of -0.5 dB). The
special value 127 indicates that the sub-carrier
is not transmitted."
SYNTAX OCTET STRING (SIZE (0..96))
Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This parameter represents the last successfully
transmitted initialization state in the last full
initialization performed on the line. States are
per the specific xDSL technology and are numbered
from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime."
SYNTAX INTEGER {
atucG9941(0),
atucQuiet1(1),
atucComb1(2),
atucQuiet2(3),
atucComb2(4),
atucIcomb1(5),
atucLineprob(6),
atucQuiet3(7),
atucComb3(8),
atucIComb2(9),
atucMsgfmt(10),
atucMsgpcb(11),
atucQuiet4(12),
atucReverb1(13),
atucTref1(14),
atucReverb2(15),
atucEct(16),
atucReverb3(17),
atucTref2(18),
atucReverb4(19),
atucSegue1(20),
atucMsg1(21),
atucReverb5(22),
atucSegue2(23),
atucMedley(24),
atucExchmarker(25),
atucMsg2(26),
atucReverb6(27),
atucSegue3(28),
atucParams(29),
atucReverb7(30),
atucSegue4(31),
atucShowtime(32),
aturG9941(100),
aturQuiet1(101),
aturComb1(102),
aturQuiet2(103),
aturComb2(104),
aturIcomb1(105),
aturLineprob(106),
aturQuiet3(107),
aturComb3(108),
aturIcomb2(109),
aturMsgfmt(110),
aturMsgpcb(111),
aturReverb1(112),
aturQuiet4(113),
aturReverb2(114),
aturQuiet5(115),
aturReverb3(116),
aturEct(117),
aturReverb4(118),
aturSegue1(119),
aturReverb5(120),
aturSegue2(121),
aturMsg1(122),
aturMedley(123),
aturExchmarker(124),
aturMsg2(125),
aturReverb6(126),
aturSegue3(127),
aturParams(128),
aturReverb7(129),
aturSegue4(130),
aturShowtime(131)
}
Adsl2LineStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters
that reflect the failure status for a given endpoint of
ADSL/ADSL2 or ADSL2+ link.
This BITS structure can report the following failures:
noDefect(0) - This bit position positively reports
that no defect or failure exists.
lossOfFrame(1) - Loss of frame synchronization.
lossOfSignal(2) - Loss of signal.
lossOfPower(3) - Loss of power. Usually this failure may
be reported for ATU-Rs only.
initFailure(4) - Recent initialization process failed.
Never active on ATU-R."
SYNTAX BITS {
noDefect(0),
lossOfFrame(1),
lossOfSignal(2),
lossOfPower(3),
initFailure(4)
}
Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for Transmission Convergence (TC)
layer of a given ATM interface (data path over an ADSL/ADSL2
or ADSL2+ link).
This BITS structure can report the following failures:
noDefect(0) - This bit position positively
reports that no defect or failure
exists.
noCellDelineation(1) - The link was successfully
initialized, but cell delineation
was never acquired on the
associated ATM data path.
lossOfCellDelineation(2) - Loss of cell delineation on the
associated ATM data path."
SYNTAX BITS {
noDefect(0),
noCellDelineation(1),
lossOfCellDelineation(2)
}
Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for a given PTM interface (packet
data path over an ADSL/ADSL2 or ADSL2+ link).
This BITS structure can report the following failures:
noDefect(0) - This bit position positively
reports that no defect or failure exists.
outOfSync(1) - Out of synchronization."
SYNTAX BITS {
noDefect(0),
outOfSync(1)
}
END