mibs/MIBS/allied/AT-LOADER-MIB

-- ============================================================================
-- AT-ETH.MIB, Allied Telesis enterprise MIB: LOADER module
--
-- Extracted from ATROUTER.MIB of pre 2.9.1 release
--
-- June 2006, Stan Xiang
--
-- Copyright (c) 2006 by Allied Telesis, Inc.
-- All rights reserved.
-- 
-- ============================================================================

AT-LOADER-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, 
    OBJECT-TYPE, 
    NOTIFICATION-TYPE
    	FROM SNMPv2-SMI

    DisplayString,
    TruthValue
        FROM SNMPv2-TC

	ifIndex
		FROM IF-MIB

	modules,
	DisplayStringUnsized
		FROM AT-SMI-MIB
;
                                 
loader MODULE-IDENTITY
    LAST-UPDATED "200702071010Z"
    ORGANIZATION "Allied Telesis, Inc"
	CONTACT-INFO
	    "http://www.alliedtelesis.com"

	DESCRIPTION
	    "To handle upload, object loadStatus is upgraded, as well as the
	     description for objects loadServer and loadFilename."

    REVISION "200702071010Z"

	DESCRIPTION
	    "This MIB file contains definitions of managed objects for the
	    LOAD module. "

    REVISION "200606281222Z"
DESCRIPTION
	"Initial Revision"

::= { modules 48 }

-- The load group. This consists of a static and dynamic entry of load
-- information and a load status variable.

-- The load table. This consists of a static and dynamic entry of load
-- information. The static information will be used if there is no dynamic
-- information available.

loadTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF LoadEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "The table of load parameters, dynamic and static."
    ::= { loader 1 }

loadEntry OBJECT-TYPE
    SYNTAX      LoadEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
            "A single entry of load parameters. This contains the
            parameters required to perform a load from the router."
    INDEX   { loadIndex }
    ::= { loadTable 1 }

LoadEntry ::=
    SEQUENCE {
        loadIndex
            INTEGER,
        loadServer
            IpAddress,
        loadDestination
            INTEGER,
        loadFilename
            DisplayString,
        loadDelay
            INTEGER
    }

loadIndex OBJECT-TYPE
    SYNTAX      INTEGER {
                static(1),
                dynamic(2)
            }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "There are two sets of load information, dynamic and static.
            The dynamic information is used once, then cleared. The static
            information is used whenever the dynamic information is not
            available. The dynamic information is also used to indicate the
            current load parameters when a load is in progress."
    ::= { loadEntry 1 }

loadServer OBJECT-TYPE
    SYNTAX      IpAddress
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "The IP address from which load will load or upload."
    ::= { loadEntry 2 }

loadDestination OBJECT-TYPE
    SYNTAX      INTEGER {
                undefined(1),
                nvs(2),
                flash(3)
            }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "The destination of the file loaded, either flash or nvs
            memory, or undefined."
    ::= { loadEntry 3 }

loadFilename OBJECT-TYPE
    SYNTAX      DisplayString
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "The file name of the file being loaded or uploaded."
    ::= { loadEntry 4 }

loadDelay OBJECT-TYPE
    SYNTAX      INTEGER
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "A delay in seconds between the initiation of the load and the
            start of the load. This allows for time to set up TFTP servers
            in cases where the terminal and TFTP server are using the same
            piece of equipment but will not work simultaneously."
    ::= { loadEntry 5 }

-- The load status value. This is used to start and reset a load, and to
-- report on the progress of a load.

loadStatus OBJECT-TYPE
    SYNTAX      INTEGER {
                idle(1),        -- loader is doing nothing
                wait(2),        -- loader is waiting to start
                loading(3),     -- loader is loading a file
                complete(4),    -- loader has successfully completed a load
                reset(5),       -- loader was aborted
                actionload(6),  -- cause a load to start
                actionstop(7),   -- cause a load/upload to stop
                actionupload(8)  -- cause a upload to start
            }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
            "Status and action object for the load module. The values 1 to
            5 are read-only values and reflect the state of the load
            module. Values 4 and 5 (complete and reset) are 'read-once',
            that is, if their values are read, either by SNMP or by manager
            console command, then they will be changed back to idle(1). The
            action values (6,7,8) cause a start and stop of the load/upload
            process respectively. Starting the load/upload can only occur if this
            field has the values 1, 4, or 5. Stopping the load can only
            occur is this field has the values 2 or 3. Reading the value of
            the loadStatus after one of actionstart or actionstop has been
            set will give one of the values 1 to 5.
            Note: A single exception to the above rules is that if the value
            of loadStatus is idle(1), then a write of 1 to this variable will
            succeed without generating an error. This exception is to allow
            certain SNMP test suites to test this variable without throwing
            up errors."
    ::= { loader 2 }
END