5725 lines
199 KiB
Plaintext
5725 lines
199 KiB
Plaintext
-- *****************************************************************
|
|
--
|
|
-- February 2009. Frank Fang
|
|
--
|
|
-- Copyright (c) 2007-2013 by cisco Systems Inc.
|
|
-- All rights reserved.
|
|
-- *****************************************************************
|
|
|
|
CISCO-WAN-3G-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
NOTIFICATION-TYPE,
|
|
Integer32,
|
|
Unsigned32,
|
|
Counter64,
|
|
Counter32,
|
|
Gauge32
|
|
FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE,
|
|
NOTIFICATION-GROUP,
|
|
OBJECT-GROUP
|
|
FROM SNMPv2-CONF
|
|
SnmpAdminString
|
|
FROM SNMP-FRAMEWORK-MIB
|
|
entPhysicalName,
|
|
entPhysicalIndex
|
|
FROM ENTITY-MIB
|
|
ifIndex
|
|
FROM IF-MIB
|
|
InetAddress,
|
|
InetAddressType
|
|
FROM INET-ADDRESS-MIB
|
|
RowStatus,
|
|
DisplayString,
|
|
TEXTUAL-CONVENTION,
|
|
TruthValue
|
|
FROM SNMPv2-TC
|
|
ciscoMgmt
|
|
FROM CISCO-SMI;
|
|
|
|
|
|
ciscoWan3gMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201308120000Z"
|
|
ORGANIZATION "Cisco Systems, Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems
|
|
Customer Service
|
|
|
|
Postal: 170 W Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
|
|
Tel: +1 800 553-NETS
|
|
|
|
E-mail: cs-3g@cisco.com
|
|
cs-4g@cisco.com"
|
|
DESCRIPTION
|
|
"This MIB module provides network management
|
|
support for Cisco cellular 3G and 4G LTE WAN products.
|
|
|
|
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
|
|
|
|
1xRTT - 1 times Radio Transmission Technology.
|
|
|
|
3G - Third generation of mobile phones standards and
|
|
technologies.
|
|
|
|
4G - Fourth generation of mobile phones standards and
|
|
technologies
|
|
|
|
Azimuth - Angle of rotation of a satellite Dish.
|
|
|
|
BER - Bit Error Ratio.
|
|
|
|
BS - Base Station.
|
|
|
|
CDMA - Code Division Multiple Access.
|
|
|
|
dB - decibel.
|
|
|
|
dBm - power ratio in decibels (dB) of the measured power
|
|
referenced to one milliwatt (mW).
|
|
|
|
CnS - Control and Status proprietary protocol for
|
|
managing the control and status of the modem.
|
|
|
|
Ec/Io - ratio of received pilot energy, Ec, to total received
|
|
energy or the total power spectral density, Io.
|
|
|
|
EDGE - Enhanced Data rate for GSM Evolution.
|
|
|
|
EPS - Evolved Packet System
|
|
|
|
EVDO - EVolution Data Optimized.
|
|
|
|
FDD - Frequency Division Duplexing
|
|
|
|
GPRS - General Packet Radio Service.
|
|
|
|
GSM - Global System for Mobile communications.
|
|
|
|
GPS - Global Positioning System.
|
|
|
|
HSDPA - High Speed Downlink Packet Access.
|
|
|
|
HSPA - High Speed Packet Access.
|
|
|
|
HSUPA - High Speed Uplink Packet Access.
|
|
|
|
LBS - Location Based Service.
|
|
|
|
LTE - Long Term Evolution
|
|
|
|
MT - Mobile Termination.
|
|
|
|
PDP - Packet Data Protocol.
|
|
|
|
PLMN - Public Land Mobile Network.
|
|
|
|
QoS - Quality of Service.
|
|
|
|
RSSI - Received Signal Strength Indication.
|
|
|
|
SDU - Service Data Unit.
|
|
|
|
SER - SDU Error Ratio.
|
|
|
|
SIM - Subscriber Identity Module.
|
|
|
|
SMS - Short Messaging Service.
|
|
|
|
SNR - Signal to Noise Ratio.
|
|
|
|
TDD - Time Division Duplexing
|
|
|
|
UMTS - Universal Mobile Telecommunication System.
|
|
|
|
WCDMA - Wideband Code Division Multiple Access."
|
|
REVISION "201308120000Z"
|
|
DESCRIPTION
|
|
"Added new notifications c3gModemTemperOnsetRecoveryNotif,
|
|
c3gModemTemperAbateRecoveryNotif."
|
|
REVISION "201207250000Z"
|
|
DESCRIPTION
|
|
"Modified Description of the ciscoWan3gMIB
|
|
module.
|
|
|
|
Modified the description of c3gWanCommonTable,
|
|
c3gWanLbsCommonTable, c3gSmsCommonTable and all its objects
|
|
to emphazise that it is technology independent.
|
|
|
|
Added enumerated value lte to objects C3gServiceCapability,
|
|
c3gCurrentIdleDigitalMode, c3gGsmPacketService.
|
|
|
|
Modified the descriptions of c3gGsmIdentityTable, and all its
|
|
objects to emphazise that these objects are applicable to both
|
|
3G and 4G-LTE Technology.
|
|
|
|
Added new object c3gGpsState to the table c3gWanCommonTable.
|
|
|
|
Added enumerated value lteBand for c3gGsmCurrentBand.
|
|
|
|
Modified ciscoWan3gMIBGsmObjectGroup,
|
|
ciscoWan3gMIBSmsObjectGroup, ciscoWan3gMIBLbsObjectGroup,
|
|
ciscoWan3gMIBGsmObjectGroup description in Module
|
|
ciscoWan3gMIBCompliance, ciscoWan3gMIBCompliance1.
|
|
|
|
Added c3gGpsState to the group ciscoWan3gMIBCommonObjectGroup."
|
|
REVISION "201207100000Z"
|
|
DESCRIPTION
|
|
"Added enumerated values rate56kbps(12) to rate8dot4mbps(18) for
|
|
C3gUmtsQosLinkBitRate."
|
|
REVISION "201008110000Z"
|
|
DESCRIPTION
|
|
"Fixed spelling errors."
|
|
REVISION "201008040000Z"
|
|
DESCRIPTION
|
|
"Added c3gWanLbs and c3gWanSms.
|
|
|
|
Added ciscoWan3gMIBSmsObjectGroup and
|
|
ciscoWan3gMIBSmsObjectGroup.
|
|
|
|
Deprecated ciscoWan3gMIBCompliance and replaced
|
|
by ciscoWan3gMIBCompliance1."
|
|
REVISION "200902050000Z"
|
|
DESCRIPTION
|
|
"Initial version of this MIB module."
|
|
::= { ciscoMgmt 661 }
|
|
|
|
|
|
|
|
C3gServiceCapability ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"3G service capability:
|
|
oneXRtt(0) - 1xRTT
|
|
evDoRel0(1) - EVDO Revision 0
|
|
evDoRelA(2) - EVDO Revision A
|
|
evDoRelB(3) - EVDO Revision B
|
|
gprs(4) - GPRS
|
|
edge(5) - EDGE
|
|
umtsWcdma(6) - UMTS/WCDMA
|
|
hsdpa(7) - HSDPA
|
|
hsupa(8) - HSUPA
|
|
hspa(9) - HSPA
|
|
hspaPlus(10) - HSPA Plus
|
|
lteTdd(11) - LTE TDD
|
|
lteFdd (12) - LTE FDD"
|
|
SYNTAX BITS {
|
|
oneXRtt(0),
|
|
evDoRel0(1),
|
|
evDoRelA(2),
|
|
evDoRelB(3),
|
|
gprs(4),
|
|
edge(5),
|
|
umtsWcdma(6),
|
|
hsdpa(7),
|
|
hsupa(8),
|
|
hspa(9),
|
|
hspaPlus(10),
|
|
lteTdd(11),
|
|
lteFdd(12)
|
|
}
|
|
|
|
C3gRssi ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Generic RSSI range."
|
|
SYNTAX Integer32 (-150..0)
|
|
|
|
C3gEcIo ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Generic EcIo range."
|
|
SYNTAX Integer32 (-150..0)
|
|
|
|
C3gTemperature ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Generic temperature range."
|
|
SYNTAX Integer32 (-50..100)
|
|
|
|
C3gPdpType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Generic PDP type."
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
ipV4(2),
|
|
ppp(3),
|
|
ipV6(4),
|
|
ipV4V6(5)
|
|
}
|
|
|
|
C3gUmtsQosTrafficClass ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS traffic classes:
|
|
subscription(1) - based on user's subscription
|
|
conversational(2) - conversational
|
|
streaming(3) - streaming
|
|
interactive(4) - interactive
|
|
background(5) - background"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
conversational(2),
|
|
streaming(3),
|
|
interactive(4),
|
|
background(5)
|
|
}
|
|
|
|
C3gUmtsQosLinkBitRate ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS link bit rate:
|
|
subscription(1) - based on user's subscription
|
|
rate16kbps(2) - 16 Kbps
|
|
rate32kbps(3) - 32 Kbps
|
|
rate64kbps(4) - 64 Kbps
|
|
rate128kbps(5) - 128 Kbps
|
|
rate256kbps(6) - 256 Kbps
|
|
rate384kbps(7) - 384 Kbps
|
|
rate1dot8mbps(8) - 1.8 Mbps
|
|
rate3dot6mbps(9) - 3.6 Mbps
|
|
rate7dot2mbps(10) - 7.2 Mbps
|
|
rate14dot4mbps(11) - 14.4 Mbps
|
|
rate56kbps(12) - 56 Kbps
|
|
rate1dot15mbps(13) - 1.15 Mbps
|
|
rate1dot6mbps(14) - 1.6 Mbps
|
|
rate2dot1mbps(15) - 2.1 Mbps
|
|
rate2dot8mbps(16) - 2.8 Mbps
|
|
rate4dot2mbps(17) - 4.2 Mbps
|
|
rate8dot4mbps(18) - 8.4 Mbps"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
rate16kbps(2),
|
|
rate32kbps(3),
|
|
rate64kbps(4),
|
|
rate128kbps(5),
|
|
rate256kbps(6),
|
|
rate384kbps(7),
|
|
rate1dot8mbps(8),
|
|
rate3dot6mbps(9),
|
|
rate7dot2mbps(10),
|
|
rate14dot4mbps(11),
|
|
rate56kbps(12),
|
|
rate1dot15mbps(13),
|
|
rate1dot6mbps(14),
|
|
rate2dot1mbps(15),
|
|
rate2dot8mbps(16),
|
|
rate4dot2mbps(17),
|
|
rate8dot4mbps(18)
|
|
}
|
|
|
|
C3gUmtsQosOrder ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS delivery order:
|
|
subscription(1) - based on user's subscription
|
|
withDeliverOrder(2) - with delivery order
|
|
withoutDeliverOrder(3) - without delivery order"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
withDeliverOrder(2),
|
|
withoutDeliverOrder(3)
|
|
}
|
|
|
|
C3gUmtsQosErroneousSdu ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS Delivery of Erroneous Service Data Unit(SDU):
|
|
subscription(1) - based on user's subscription
|
|
noDetect(2) - no detect
|
|
errSduDeliver(3) - erroneous SDUs are delivered
|
|
errSduNotDeliver(4) - erroneous SDUs are not delivered"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
noDetect(2),
|
|
errSduDeliver(3),
|
|
errSduNotDeliver(4)
|
|
}
|
|
|
|
C3gUmtsQosSer ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS SDU error ratio:
|
|
subscription(1) - based on user's subscription
|
|
oneExpMinus2(2) - 1E-2
|
|
sevenExpMinus3(3) - 7E-3
|
|
oneExpMinus3(4) - 1E-3
|
|
oneExpMinus4(5) - 1E-4
|
|
oneExpMinus5(6) - 1E-5
|
|
oneExpMinus6(7) - 1E-6
|
|
oneExpMinus1(8) - 1E-1"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
oneExpMinus2(2),
|
|
sevenExpMinus3(3),
|
|
oneExpMinus3(4),
|
|
oneExpMinus4(5),
|
|
oneExpMinus5(6),
|
|
oneExpMinus6(7),
|
|
oneExpMinus1(8)
|
|
}
|
|
|
|
C3gUmtsQosBer ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS residual bit error ratio (BER):
|
|
subscription(1) - based on user's subscription
|
|
fiveExpMinus2(2) - 5E-2
|
|
oneExpMinus2(3) - 1E-2
|
|
fiveExpMinus3(4) - 5E-3
|
|
fourExpMinus3(5) - 4E-3
|
|
oneExpMinus3(6) - 1E-3
|
|
oneExpMinus4(7) - 1E-4
|
|
oneExpMinus5(8) - 1E-5
|
|
oneExpMinus6(9) - 1E-6
|
|
sixExpMinus8(10) - 6E-8"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
fiveExpMinus2(2),
|
|
oneExpMinus2(3),
|
|
fiveExpMinus3(4),
|
|
fourExpMinus3(5),
|
|
oneExpMinus3(6),
|
|
oneExpMinus4(7),
|
|
oneExpMinus5(8),
|
|
oneExpMinus6(9),
|
|
sixExpMinus8(10)
|
|
}
|
|
|
|
C3gUmtsQosPriority ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS traffic handling priority:
|
|
subscription(1) - based on user's subscription
|
|
level1(2) - priority level 1
|
|
level2(3) - priority level 2
|
|
level3(4) - priority level 3"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
level1(2),
|
|
level2(3),
|
|
level3(4)
|
|
}
|
|
|
|
C3gUmtsQosSrcStatDescriptor ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS source statistics descriptor:
|
|
unknown(1) - unknown
|
|
speech(2) - speech"
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
speech(2)
|
|
}
|
|
|
|
C3gUmtsQosSignalIndication ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"UMTS QoS signalling indication:
|
|
notOptimized(1) - not optimized for signalling traffic
|
|
optimized(2) - optimized for signalling traffic"
|
|
SYNTAX INTEGER {
|
|
notOptimized(1),
|
|
optimized(2)
|
|
}
|
|
|
|
C3gGprsQosPrecedence ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS QoS precedence:
|
|
subscription(1) - based on user's subscription
|
|
highPriority(2) - high priority
|
|
normalPriority(3) - normal priority
|
|
lowPriority(4) - low priority"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
highPriority(2),
|
|
normalPriority(3),
|
|
lowPriority(4)
|
|
}
|
|
|
|
C3gGprsQosDelay ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS QoS delay classes:
|
|
subscription(1) - based on user's subscription
|
|
delayClass1(2) - delay class 1
|
|
delayClass2(3) - delay class 2
|
|
delayClass3(4) - delay class 3
|
|
delayClass4(5) - delay class 4"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
delayClass1(2),
|
|
delayClass2(3),
|
|
delayClass3(4),
|
|
delayClass4(5)
|
|
}
|
|
|
|
C3gGprsQosReliability ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS QoS reliability:
|
|
subscription(1) - based on user's subscription
|
|
ackGtpLlcRlcProtData(2) - acknowledged GTP, LLC, and RLC;
|
|
protected data
|
|
unAckGtpAckLlcRlcProtData(3) - unacknowledged GTP, acknowledged
|
|
LLC and RLC; protected data
|
|
unAckGtpLlcAckRlcProtData(4) - unacknowledged GTP and LLC,
|
|
acknowledged RLC; protected data
|
|
unAckGtpLlcRlcProtData(5) - unacknowledged GTP, LLC, and
|
|
RLC; protected data
|
|
unAckGtpLlcRlcUnProtData(6) - unacknowledged GTP, LLC, and
|
|
RLC; unprotected data"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
ackGtpLlcRlcProtData(2),
|
|
unAckGtpAckLlcRlcProtData(3),
|
|
unAckGtpLlcAckRlcProtData(4),
|
|
unAckGtpLlcRlcProtData(5),
|
|
unAckGtpLlcRlcUnProtData(6)
|
|
}
|
|
|
|
C3gGprsQosPeakRate ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS QoS peak rate:
|
|
subscription(1) - based on user's subscription
|
|
upTo1kops(2) - up to 1000 octet/second
|
|
upTo2kops(3) - up to 2000 octet/second
|
|
upTo4kops(4) - up to 4000 octet/second
|
|
upTo8kops(5) - up to 8000 octet/second
|
|
upTo16kops(6) - up to 16000 octet/second
|
|
upTo32kops(7) - up to 32000 octet/second
|
|
upTo64kops(8) - up to 64000 octet/second
|
|
upTo128kops(9) - up to 128000 octet/second
|
|
upTo256kops(10) - up to 256000 octet/second"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
upTo1kops(2),
|
|
upTo2kops(3),
|
|
upTo4kops(4),
|
|
upTo8kops(5),
|
|
upTo16kops(6),
|
|
upTo32kops(7),
|
|
upTo64kops(8),
|
|
upTo128kops(9),
|
|
upTo256kops(10)
|
|
}
|
|
|
|
C3gGprsQosMeanRate ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS QoS mean rate:
|
|
subscription(1) - based on user's subscription
|
|
rate100(2) - 100 octet/hour
|
|
rate200(3) - 200 octet/hour
|
|
rate500(4) - 500 octet/hour
|
|
rate1k(5) - 1000 octet/hour
|
|
rate2k(6) - 2000 octet/hour
|
|
rate5k(7) - 5000 octet/hour
|
|
rate10k(8) - 10000 octet/hour
|
|
rate20k(9) - 20000 octet/hour
|
|
rate50k(10) - 50000 octet/hour
|
|
rate100k(11) - 100000 octet/hour
|
|
rate200k(12) - 200000 octet/hour
|
|
rate500k(13) - 500000 octet/hour
|
|
rate1m(14) - 1000000 octet/hour
|
|
rate2m(15) - 2000000 octet/hour
|
|
rate5m(16) - 5000000 octet/hour
|
|
rate10m(17) - 10000000 octet/hour
|
|
rate20m(18) - 20000000 octet/hour
|
|
rate50m(19) - 50000000 octet/hour
|
|
resv1(20) - reserved 1 (for future use)
|
|
resv2(21) - reserved 2 (for future use)
|
|
resv3(22) - reserved 3 (for future use)
|
|
resv4(23) - reserved 4 (for future use)
|
|
resv5(24) - reserved 5 (for future use)
|
|
resv6(25) - reserved 6 (for future use)
|
|
resv7(26) - reserved 7 (for future use)
|
|
resv8(27) - reserved 8 (for future use)
|
|
resv9(28) - reserved 9 (for future use)
|
|
resv10(29) - reserved 10 (for future use)
|
|
resv11(30) - reserved 11 (for future use)
|
|
resv12(31) - reserved 12 (for future use)
|
|
bestEffort(32) - best effort"
|
|
SYNTAX INTEGER {
|
|
subscription(1),
|
|
rate100(2),
|
|
rate200(3),
|
|
rate500(4),
|
|
rate1k(5),
|
|
rate2k(6),
|
|
rate5k(7),
|
|
rate10k(8),
|
|
rate20k(9),
|
|
rate50k(10),
|
|
rate100k(11),
|
|
rate200k(12),
|
|
rate500k(13),
|
|
rate1m(14),
|
|
rate2m(15),
|
|
rate5m(16),
|
|
rate10m(17),
|
|
rate20m(18),
|
|
rate50m(19),
|
|
resv1(20),
|
|
resv2(21),
|
|
resv3(22),
|
|
resv4(23),
|
|
resv5(24),
|
|
resv6(25),
|
|
resv7(26),
|
|
resv8(27),
|
|
resv9(28),
|
|
resv10(29),
|
|
resv11(30),
|
|
resv12(31),
|
|
bestEffort(32)
|
|
}
|
|
-- Textual Conventions definition will be defined before this objects
|
|
|
|
ciscoWan3gMIBNotifs OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIB 0 }
|
|
|
|
ciscoWan3gMIBObjects OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIB 1 }
|
|
|
|
ciscoWan3gMIBConform OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIB 2 }
|
|
|
|
|
|
c3gWanCommonTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gWanCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular common objects table which is technology
|
|
independent."
|
|
::= { ciscoWan3gMIBObjects 1 }
|
|
|
|
c3gWanCommonEntry OBJECT-TYPE
|
|
SYNTAX C3gWanCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gWanCommonTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gWanCommonTable 1 }
|
|
|
|
C3gWanCommonEntry ::= SEQUENCE {
|
|
c3gStandard INTEGER,
|
|
c3gCapability C3gServiceCapability,
|
|
c3gModemState INTEGER,
|
|
c3gPreviousServiceType C3gServiceCapability,
|
|
c3gCurrentServiceType C3gServiceCapability,
|
|
c3gRoamingStatus INTEGER,
|
|
c3gCurrentSystemTime DisplayString,
|
|
c3gConnectionStatus INTEGER,
|
|
c3gNotifRadioService C3gServiceCapability,
|
|
c3gNotifRssi C3gRssi,
|
|
c3gNotifEcIo C3gEcIo,
|
|
c3gModemTemperature C3gTemperature,
|
|
c3gRssiOnsetNotifThreshold C3gRssi,
|
|
c3gRssiAbateNotifThreshold C3gRssi,
|
|
c3gEcIoOnsetNotifThreshold C3gEcIo,
|
|
c3gEcIoAbateNotifThreshold C3gEcIo,
|
|
c3gModemTemperOnsetNotifThreshold C3gTemperature,
|
|
c3gModemTemperAbateNotifThreshold C3gTemperature,
|
|
c3gModemReset INTEGER,
|
|
c3gModemUpNotifEnabled TruthValue,
|
|
c3gModemDownNotifEnabled TruthValue,
|
|
c3gServiceChangedNotifEnabled TruthValue,
|
|
c3gNetworkChangedNotifEnabled TruthValue,
|
|
c3gConnectionStatusChangedNotifFlag BITS,
|
|
c3gRssiOnsetNotifFlag C3gServiceCapability,
|
|
c3gRssiAbateNotifFlag C3gServiceCapability,
|
|
c3gEcIoOnsetNotifFlag C3gServiceCapability,
|
|
c3gEcIoAbateNotifFlag C3gServiceCapability,
|
|
c3gModemTemperOnsetNotifEnabled TruthValue,
|
|
c3gModemTemperAbateNotifEnabled TruthValue,
|
|
c3gGpsState TruthValue
|
|
}
|
|
|
|
c3gStandard OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
cdma(1),
|
|
gsm(2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular Standard: GSM (Global System for Mobile
|
|
communications, 3GPP), CDMA (Code Division Multiple
|
|
Access, 3GPP-2). GSM standard also include 4G-LTE
|
|
technology mode"
|
|
::= { c3gWanCommonEntry 1 }
|
|
|
|
c3gCapability OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular service capability. It currently includes the 2G,
|
|
3G and 4G-LTE standard."
|
|
::= { c3gWanCommonEntry 2 }
|
|
|
|
c3gModemState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
up(2),
|
|
down(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular modem state, up(2) indicates modem can be detected
|
|
and down(3) indicates modem can not be detected."
|
|
DEFVAL { down }
|
|
::= { c3gWanCommonEntry 3 }
|
|
|
|
c3gPreviousServiceType OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the previous service type when service
|
|
type changes."
|
|
::= { c3gWanCommonEntry 4 }
|
|
|
|
c3gCurrentServiceType OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the current service type when service
|
|
type changes."
|
|
::= { c3gWanCommonEntry 5 }
|
|
|
|
c3gRoamingStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
roaming(2),
|
|
home(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular current roaming status."
|
|
::= { c3gWanCommonEntry 6 }
|
|
|
|
c3gCurrentSystemTime OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular current system time received from base station."
|
|
::= { c3gWanCommonEntry 7 }
|
|
|
|
c3gConnectionStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
error(2),
|
|
connecting(3),
|
|
dormant(4),
|
|
connected(5),
|
|
disconnected(6),
|
|
idle(7),
|
|
active(8),
|
|
inactive(9)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the current connection status."
|
|
::= { c3gWanCommonEntry 8 }
|
|
|
|
c3gNotifRadioService OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used as one of the var-bind object when
|
|
notification for RSSI or Ec/Io is generated. This object
|
|
indicates which service generates the notification."
|
|
::= { c3gWanCommonEntry 9 }
|
|
|
|
c3gNotifRssi OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used as one of the var-bind object when
|
|
notification for RSSI is generated. The relevant RSSI will be
|
|
copied into c3gNotifRssi which corresponds to the service
|
|
indicated in c3gNotifRadioService object. This object will
|
|
reflect the value of one of the following objects:
|
|
c3gCurrent1xRttRssi, c3gCurrentEvDoRssi and c3gCurrentGsmRssi.
|
|
User should not use this object to get the current RSSI value as
|
|
this object is used to indicate the RSSI value that triggers
|
|
c3gRssiOnsetNotif or c3gRssiAbateNotif notification."
|
|
::= { c3gWanCommonEntry 10 }
|
|
|
|
c3gNotifEcIo OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used as one of the var-bind object when
|
|
notification for Ec/Io is generated. The relevant Ec/Io will
|
|
be copied into c3gNotifEcIo which corresponds to the service
|
|
indicated in c3gNotifRadioService object. This object will
|
|
reflect the value of one of the following objects:
|
|
c3gCurrent1xRttEcIo, c3gCurrentEvDoEcIo and c3gCurrentGsmEcIo.
|
|
User should not use this object to get the current Ec/Io value
|
|
as this object is used to indicate the Ec/Io value that triggers
|
|
c3gEcIoOnsetNotif or c3gEcIoAbateNotif notification."
|
|
::= { c3gWanCommonEntry 11 }
|
|
|
|
c3gModemTemperature OBJECT-TYPE
|
|
SYNTAX C3gTemperature
|
|
UNITS "degrees Celsius"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The modem temperature."
|
|
::= { c3gWanCommonEntry 12 }
|
|
|
|
c3gRssiOnsetNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The RSSI onset threshold value. If RSSI goes below the
|
|
threshold and the service bit in c3gRssiOnsetNotifFlag is
|
|
set, the c3gRssiOnsetNotif notification for that service
|
|
will be sent. The absolute value of
|
|
c3gRssiAbateNotifThreshold should be less than or equal to
|
|
the absolute value of c3gRssiOnsetNotifThreshold
|
|
(|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|).
|
|
e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then
|
|
setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
|
|
and will be rejected."
|
|
DEFVAL { -150 }
|
|
::= { c3gWanCommonEntry 13 }
|
|
|
|
c3gRssiAbateNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The RSSI abate threshold value. If RSSI goes above the
|
|
threshold and the service bit in c3gRssiAbateNotifFlag is
|
|
set, the c3gRssiAbateNotif notification for that service will
|
|
be sent. The absolute value of c3gRssiAbateNotifThreshold
|
|
should be less than or equal to the absolute value of
|
|
c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <=
|
|
|c3gRssiOnsetNotifThreshold|). e.g. setting
|
|
c3gRssiAbateNotifThreshold to -115 dBm and then setting
|
|
c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
|
|
and will be rejected."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanCommonEntry 14 }
|
|
|
|
c3gEcIoOnsetNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
UNITS "dB"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The EcIo onset threshold value. If EcIo goes below the
|
|
threshold and the service bit in c3gEcIoOnsetNotifFlag is set,
|
|
the c3gEcIoOnsetNotif notification for that service will be
|
|
sent. The absolute value of c3gEcIoAbateNotifThreshold should
|
|
be less than or equal to the absolute value of
|
|
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|
|
|c3gEcIoOnsetNotifThreshold|). e.g. setting
|
|
c3gEcIoAbateNotifThreshold to -15 dB and then setting
|
|
c3gEcIoOnsetNotifThreshold to -10 dB is not allowed and will
|
|
be rejected."
|
|
DEFVAL { -150 }
|
|
::= { c3gWanCommonEntry 15 }
|
|
|
|
c3gEcIoAbateNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
UNITS "dB"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The threshold value that if EcIo goes above the threshold and
|
|
the service bit in c3gEcIoAbateNotifFlag is set, the
|
|
c3gEcIoAbateNotif notification for that service will be sent.
|
|
The absolute value of c3gEcIoAbateNotifThreshold
|
|
should be less than or equal to the absolute value of
|
|
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|
|
|c3gEcIoOnsetNotifThreshold|). e.g. setting
|
|
c3gEcIoOnsetNotifThreshold to -15 dB and then setting
|
|
c3gEcIoAbateNotifThreshold to -10 dB is not allowed and will
|
|
be rejected."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanCommonEntry 16 }
|
|
|
|
c3gModemTemperOnsetNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gTemperature
|
|
UNITS "degrees Celsius"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The modem temperature onset threshold value. If modem
|
|
temperature goes above the threshold and the value of
|
|
c3gModemTemperOnsetNotifEnabled is 'true',
|
|
the c3gModemTemperOnsetNotif notification will be sent.
|
|
The value of c3gModemTemperAbateNotifThreshold should be less
|
|
than or equal to the value of
|
|
c3gModemTemperOnsetNotifThreshold. e.g. setting
|
|
c3gModemTemperAbateNotifThreshold to 50 degree Celsius and
|
|
then setting c3gModemTemperOnsetNotifThreshold to
|
|
40 degree Celsius is not allowed and will be rejected."
|
|
DEFVAL { 100 }
|
|
::= { c3gWanCommonEntry 17 }
|
|
|
|
c3gModemTemperAbateNotifThreshold OBJECT-TYPE
|
|
SYNTAX C3gTemperature
|
|
UNITS "degrees Celsius"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The modem temperature abate threshold value. If modem
|
|
temperature goes below the threshold and the value of
|
|
c3gModemTemperAbateNotifEnabled is 'true', the
|
|
c3gModemTemperAbateNotif notification will be sent. The value
|
|
of c3gModemTemperAbateNotifThreshold should be less than or
|
|
equal to the value of c3gModemTemperOnsetNotifThreshold.
|
|
e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree
|
|
Celsius and then setting c3gModemTemperOnsetNotifThreshold
|
|
to 40 degree Celsius is not allowed and will be rejected."
|
|
DEFVAL { -50 }
|
|
::= { c3gWanCommonEntry 18 }
|
|
|
|
c3gModemReset OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
reset(1),
|
|
powerCycle(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to reset or power-cycle the modem."
|
|
::= { c3gWanCommonEntry 19 }
|
|
|
|
c3gModemUpNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of modem
|
|
up notification c3gModemUpNotif."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 20 }
|
|
|
|
c3gModemDownNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of modem
|
|
down notification c3gModemDownNotif."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 21 }
|
|
|
|
c3gServiceChangedNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of service
|
|
changed notification c3gServiceChangedNotif."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 22 }
|
|
|
|
c3gNetworkChangedNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of network
|
|
changed notification c3gNetworkChangedNotif."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 23 }
|
|
|
|
c3gConnectionStatusChangedNotifFlag OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
unknown(0),
|
|
error(1),
|
|
connecting(2),
|
|
dormant(3),
|
|
connected(4),
|
|
disconnected(5),
|
|
idle(6),
|
|
active(7),
|
|
inactive(8)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the flag bitmap to control the generation of
|
|
notification c3gConnectionStatusChangedNotif. e.g. setting bit
|
|
0 (error(0)) to 1 and bit 4 (disconnected(4)) to 1 will cause
|
|
the notification c3gConnectionStatusChangedNotif to be
|
|
generated when object c3gConnetionStatus changes the status to
|
|
error or disconnected. The default value of this object is
|
|
'00'H."
|
|
::= { c3gWanCommonEntry 24 }
|
|
|
|
c3gRssiOnsetNotifFlag OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the flag bitmap to control the generation of
|
|
notification c3gRssiOnsetNotif. Each bit represents a service
|
|
as defined in C3gServiceCapability, set the bit value to 1 to
|
|
enable (and 0 to disable) the generation of notification
|
|
c3gRssiOnsetNotif for that service. The default value of this
|
|
object is all bits are 0."
|
|
::= { c3gWanCommonEntry 25 }
|
|
|
|
c3gRssiAbateNotifFlag OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the flag bitmap to control the generation of
|
|
notification c3gRssiAbateNotif. Each bit represents a service
|
|
as defined in C3gServiceCapability, set the bit value to 1 to
|
|
enable (and 0 to disable) the generation of notification
|
|
c3gRssiAbateNotif for that service. The default value of this
|
|
object is all bits are 0."
|
|
::= { c3gWanCommonEntry 26 }
|
|
|
|
c3gEcIoOnsetNotifFlag OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the flag bitmap to control the generation of
|
|
notification c3gEcIoOnsetNotif. Each bit represents a service
|
|
as defined in C3gServiceCapability, set the bit value to 1 to
|
|
enable (and 0 to disable) the generation of notification
|
|
c3gEcIoOnsetNotif for that service. The default value of this
|
|
object is all bits are 0."
|
|
::= { c3gWanCommonEntry 27 }
|
|
|
|
c3gEcIoAbateNotifFlag OBJECT-TYPE
|
|
SYNTAX C3gServiceCapability
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the flag bitmap to control the generation of
|
|
notification c3gEcIoAbateNotif. Each bit represents a service
|
|
as defined in C3gServiceCapability, set the bit value to 1 to
|
|
enable (and 0 to disable) the generation of notification
|
|
c3gEcIoAbateNotif for that service. The default value of this
|
|
object is all bits are 0."
|
|
::= { c3gWanCommonEntry 28 }
|
|
|
|
c3gModemTemperOnsetNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of
|
|
c3gModemTemperOnsetNotif notification."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 29 }
|
|
|
|
c3gModemTemperAbateNotifEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to enable/disable the generation of
|
|
c3gModemTemperAbateNotif notification."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 30 }
|
|
|
|
c3gGpsState OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to determine or enable/disable
|
|
the GPS state."
|
|
DEFVAL { false }
|
|
::= { c3gWanCommonEntry 31 }
|
|
|
|
|
|
c3gWanCdma OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBObjects 2 }
|
|
|
|
c3gWanGsm OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBObjects 3 }
|
|
|
|
c3gWanLbs OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBObjects 4 }
|
|
|
|
c3gWanSmsCommon OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBObjects 5 }
|
|
|
|
|
|
c3gCdmaSessionTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaSessionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table describes wireless session (link) created when a
|
|
modem connects to a particular cellular network. One or more
|
|
logical calls can be placed over wireless session(link). These
|
|
logical calls are represented in the c3gCdmaConnectionTable."
|
|
::= { c3gWanCdma 1 }
|
|
|
|
c3gCdmaSessionEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaSessionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaSessionTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaSessionTable 1 }
|
|
|
|
C3gCdmaSessionEntry ::= SEQUENCE {
|
|
c3gCdmaTotalCallDuration Counter64,
|
|
c3gCdmaTotalTransmitted Counter64,
|
|
c3gCdmaTotalReceived Counter64,
|
|
c3gHdrDdtmPreference INTEGER
|
|
}
|
|
|
|
c3gCdmaTotalCallDuration OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Total duration of all calls."
|
|
::= { c3gCdmaSessionEntry 1 }
|
|
|
|
c3gCdmaTotalTransmitted OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Total data transmitted for all calls. It is the total amount
|
|
of data transmitted by modem, not to be confused with the number
|
|
of bytes transmitted through the interface."
|
|
::= { c3gCdmaSessionEntry 2 }
|
|
|
|
c3gCdmaTotalReceived OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Total data received for all calls. It is the total amount of
|
|
data received by modem, not to be confused with the number of
|
|
bytes received from the interface."
|
|
::= { c3gCdmaSessionEntry 3 }
|
|
|
|
c3gHdrDdtmPreference OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
off(2),
|
|
on(3),
|
|
noChange(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR Data Dedicated Transmission Mode (DDTM) preference:
|
|
unknown(1) - DDTM preference is unknown
|
|
off(2) - DDTM preference set to OFF
|
|
on(3) - DDTM preference set to ON
|
|
noChange(4) - DDTM preference is no change"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaSessionEntry 4 }
|
|
|
|
|
|
|
|
c3gCdmaConnectionTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaConnectionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA connection table. This table describes
|
|
logical connections/calls over wireless link, the wireless link
|
|
is described in c3gCdmaSessionTable."
|
|
::= { c3gWanCdma 2 }
|
|
|
|
c3gCdmaConnectionEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaConnectionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaConnectionTable."
|
|
INDEX { ifIndex }
|
|
::= { c3gCdmaConnectionTable 1 }
|
|
|
|
C3gCdmaConnectionEntry ::= SEQUENCE {
|
|
c3gOutgoingCallNumber DisplayString,
|
|
c3gHdrAtState INTEGER,
|
|
c3gHdrSessionState INTEGER,
|
|
c3gUati DisplayString,
|
|
c3gColorCode Unsigned32,
|
|
c3gRati Unsigned32,
|
|
c3gHdrSessionDuration Unsigned32,
|
|
c3gHdrSessionStart Unsigned32,
|
|
c3gHdrSessionEnd Unsigned32,
|
|
c3gAuthStatus INTEGER,
|
|
c3gHdrDrc Unsigned32,
|
|
c3gHdrDrcCover Unsigned32,
|
|
c3gHdrRri INTEGER,
|
|
c3gMobileIpErrorCode Integer32,
|
|
c3gCdmaCurrentTransmitted Counter64,
|
|
c3gCdmaCurrentReceived Counter64,
|
|
c3gCdmaCurrentCallStatus INTEGER,
|
|
c3gCdmaCurrentCallDuration Unsigned32,
|
|
c3gCdmaCurrentCallType INTEGER,
|
|
c3gCdmaLastCallDisconnReason INTEGER,
|
|
c3gCdmaLastConnError INTEGER
|
|
}
|
|
|
|
c3gOutgoingCallNumber OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Phone number of outgoing call."
|
|
::= { c3gCdmaConnectionEntry 1 }
|
|
|
|
c3gHdrAtState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
inactive(2),
|
|
acquisition(3),
|
|
sync(4),
|
|
idle(5),
|
|
access(6),
|
|
connected(7)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"High Data Rate (HDR) Access Terminal (AT) state."
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaConnectionEntry 2 }
|
|
|
|
c3gHdrSessionState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
open(2),
|
|
close(3),
|
|
addressManagementProtocolSetup(4),
|
|
atInitiated(5),
|
|
anInitiated(6)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"High Data Rate (HDR) session state."
|
|
::= { c3gCdmaConnectionEntry 3 }
|
|
|
|
c3gUati OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Unicast Access Terminal Identifier (UATI), AT seeking access
|
|
to the 1 times EV-DO system receives a UATI allocated from the
|
|
system after setting up a radio traffic channel with a base
|
|
station."
|
|
::= { c3gCdmaConnectionEntry 4 }
|
|
|
|
c3gColorCode OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Color code. A sync channel may be used by the base station
|
|
to communicate administrative information to a mobile station.
|
|
For example, a base station may transmit a base station ID to a
|
|
user, a color code and administrative information identifying
|
|
system status."
|
|
::= { c3gCdmaConnectionEntry 5 }
|
|
|
|
c3gRati OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Random Access Terminal Identifier (RATI). AT transmits a
|
|
UATI request message to the ANC using the RATI to make a UATI
|
|
allocation request."
|
|
::= { c3gCdmaConnectionEntry 6 }
|
|
|
|
c3gHdrSessionDuration OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR connection session duration. It is the duration
|
|
between c3gHdrSessionStart and c3gHdrSessionEnd."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 7 }
|
|
|
|
c3gHdrSessionStart OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR connection session starting time."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 8 }
|
|
|
|
c3gHdrSessionEnd OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR connection session ending time."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 9 }
|
|
|
|
c3gAuthStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
notAuthenticated(2),
|
|
authenticated(3),
|
|
failed(4),
|
|
authenticationDisabled(5)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Connection authentication status:
|
|
unknown(1) - authentication status is unknown
|
|
notAuthenticated(2) - not yet authenticated.
|
|
authenticated(3) - authenticated.
|
|
failed(4) - authentication failed.
|
|
authenticationDisabled(5) - authentication disabled"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaConnectionEntry 10 }
|
|
|
|
c3gHdrDrc OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"High Data Rate (HDR) Data Rate Control (DRC). AT provides
|
|
requests for data transmissions by sending a Data Rate Control,
|
|
DRC, message via a specific channel referred to as the DRC
|
|
channel."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 11 }
|
|
|
|
c3gHdrDrcCover OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR DRC cover. The DRC cover is a coding applied to
|
|
identify the sector from which the data is to be transmitted.
|
|
In one embodiment, the DRC cover is a Walsh code applied to
|
|
the DRC value, wherein a unique code corresponds to each sector
|
|
in the Active Set of the AT."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 12 }
|
|
|
|
c3gHdrRri OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
pilotOnly(2),
|
|
rri9dot6kbps(3),
|
|
rri19dot2kbps(4),
|
|
rri38dot4kbps(5),
|
|
rri76dot8kbps(6),
|
|
rri153dot6kbps(7)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"HDR Rate Request Indicator (RRI). RRI provides the
|
|
structure of a frame currently being transmitted when frames
|
|
are transmitted at different rates. Services at different rates
|
|
are reliably provided by the RRI:
|
|
unknown(1) - RRI unknown
|
|
pilotOnly(2) - pilot channel only
|
|
rri9dot6kbps(3) - RRI is 9.6 Kbit/s
|
|
rri19dot2kbps(4) - RRI is 19.2 Kbit/s
|
|
rri38dot4kbps(5) - RRI is 38.4 Kbit/s
|
|
rri76dot8kbps(6) - RRI is 76.8 Kbit/s
|
|
rri153dot6kbps(7) - RRI is 153.6 Kbit/s"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaConnectionEntry 13 }
|
|
|
|
c3gMobileIpErrorCode OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile IP error code (please refer to RFC 2002)."
|
|
::= { c3gCdmaConnectionEntry 14 }
|
|
|
|
c3gCdmaCurrentTransmitted OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current number of bytes transmitted by modem for current
|
|
connection."
|
|
::= { c3gCdmaConnectionEntry 15 }
|
|
|
|
c3gCdmaCurrentReceived OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current number of bytes received by modem for current
|
|
connection."
|
|
::= { c3gCdmaConnectionEntry 16 }
|
|
|
|
c3gCdmaCurrentCallStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
error(2),
|
|
connecting(3),
|
|
dormant(4),
|
|
connected(5),
|
|
disconnected(6)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current call status."
|
|
::= { c3gCdmaConnectionEntry 17 }
|
|
|
|
c3gCdmaCurrentCallDuration OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current call duration."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaConnectionEntry 18 }
|
|
|
|
c3gCdmaCurrentCallType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
asyncData(2),
|
|
voiceCall(3),
|
|
packet1xRttCall(4),
|
|
atAsyncDataCall(5),
|
|
atVoiceCall(6),
|
|
atPacketCall(7),
|
|
faxCall(8),
|
|
smsCall(9),
|
|
otaCall(10),
|
|
testCall(11),
|
|
callWaiting(12),
|
|
positionDetermination(13),
|
|
dormant(14),
|
|
e911Call(15)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current call type."
|
|
::= { c3gCdmaConnectionEntry 19 }
|
|
|
|
c3gCdmaLastCallDisconnReason OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
modemOffline(2),
|
|
modemCdmaLocTilPowCyc(3),
|
|
noService(4),
|
|
abnormalCallEnd(5),
|
|
baseStatIntercept(6),
|
|
baseStatRelease(7),
|
|
baseStatReleaseNoReas(8),
|
|
baseStatReleaseSoRej(9),
|
|
incomingCall(10),
|
|
baseStatAlertStop(11),
|
|
clientEndedCall(12),
|
|
activationEndedOtasp(13),
|
|
ndssFailure(14),
|
|
maxAccesProbTransmit(15),
|
|
persistTestFailure(16),
|
|
ruimNotPresent(17),
|
|
accessAttemptInProg(18),
|
|
reasonUnspecified(19),
|
|
recdRetryOrder(20),
|
|
modemLocked(21),
|
|
gpsCallEnded(22),
|
|
smsCallEnded(23),
|
|
noConcurrentService(24),
|
|
noResponseFromBs(25),
|
|
rejectedByBs(26),
|
|
notCompatConcurServ(27),
|
|
accessBlockedByBs(28),
|
|
alreadyOnTraffChann(29),
|
|
emergencyCall(30),
|
|
dataCallEnded(31),
|
|
busyHdr(32),
|
|
billingOrAuthErrHdr(33),
|
|
sysChangeDueToPrlHdr(34),
|
|
hdrExitDueToPrl(35),
|
|
noSessionHdr(36),
|
|
callEndedHdr(37)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Last call disconnect reason:
|
|
unknown(1) - Unknown
|
|
modemOffline(2) - Modem offline
|
|
modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle
|
|
noService(4) - No service
|
|
abnormalCallEnd(5) - Abnormal call end
|
|
baseStatIntercept(6) - Base station intercept
|
|
baseStatRelease(7) - Base station release
|
|
baseStatReleaseNoReas(8) - Base station release (No reason)
|
|
baseStatReleaseSoRej(9) - Base station release (SO reject)
|
|
incomingCall(10) - Incoming call
|
|
baseStatAlertStop(11) - Base station alert stop
|
|
clientEndedCall(12) - Client ended call
|
|
activationEndedOtasp(13) - Activation ended OTASP (Over-
|
|
The-Air Service Provisioning)
|
|
ndssFailure(14) - NDSS (Network and Distributed
|
|
System Security) failure
|
|
maxAccesProbTransmit(15) - Max access probes transmitted
|
|
persistTestFailure(16) - Persistence test failure
|
|
ruimNotPresent(17) - RUIM (Removable User Identity
|
|
Module) not present
|
|
accessAttemptInProg(18) - Access attempt in progress
|
|
reasonUnspecified(19) - Reason unspecified
|
|
recdRetryOrder(20) - Recd retry order
|
|
modemLocked(21) - Modem Locked
|
|
gpsCallEnded(22) - GPS call ended
|
|
smsCallEnded(23) - SMS (Short Message Service)
|
|
call ended
|
|
noConcurrentService(24) - No concurrent service
|
|
noResponseFromBs(25) - No response from BS (Base station)
|
|
rejectedByBs(26) - Rejected by BS
|
|
notCompatConcurServ(27) - Not compatible concurrent service
|
|
accessBlockedByBs(28) - Access blocked by BS
|
|
alreadyOnTraffChann(29) - Already on Traffic channel
|
|
emergencyCall(30) - Emergency call
|
|
dataCallEnded(31) - Data call ended
|
|
busyHdr(32) - Busy (HDR)
|
|
billingOrAuthErrHdr(33) - Billing or Auth error (HDR)
|
|
sysChangeDueToPrlHdr(34) - System change due to PRL (HDR)
|
|
hdrExitDueToPrl(35) - HDR exit due to PRL (HDR)
|
|
noSessionHdr(36) - No Session (HDR)
|
|
callEndedHdr(37) - Call ended (HDR)"
|
|
::= { c3gCdmaConnectionEntry 20 }
|
|
|
|
c3gCdmaLastConnError OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
invalidClientId(2),
|
|
badCallType(3),
|
|
badServiceType(4),
|
|
expectingNumber(5),
|
|
nullNumberBuffer(6),
|
|
invalidDigits(7),
|
|
outOfRangeNumber(8),
|
|
nullAalphaBuffer(9),
|
|
outOfRangeAlphaNumber(10),
|
|
invalidOtaspActivatCode(11),
|
|
modemOffline(12),
|
|
modemLocked(13),
|
|
unsupportedFlash(14),
|
|
dialedNumberProhibited(15),
|
|
onlyE911Calls(16),
|
|
modemInUse(17),
|
|
unsupportedServiceType(18),
|
|
wrongCallType(19),
|
|
invalidCommandCallState(20),
|
|
invalidCommandModemState(21),
|
|
noValidService(22),
|
|
cannotAnswerIncomingCall(23),
|
|
badPrivacySetting(24),
|
|
noCommandBuffers(25),
|
|
communicationProblem(26),
|
|
unspecifiedError(27),
|
|
invalidLastActiveNetwork(28),
|
|
noCollocatedHdr(29),
|
|
uimNotPresent(30)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Last connect error:
|
|
none(1) - None
|
|
invalidClientId(2) - Invalid client ID
|
|
badCallType(3) - Bad call type
|
|
badServiceType(4) - Bad service type
|
|
expectingNumber(5) - Expecting number
|
|
nullNumberBuffer(6) - Null number buffer
|
|
invalidDigits(7) - Invalid digits
|
|
outOfRangeNumber(8) - Out of range number
|
|
nullAalphaBuffer(9) - Null alpha buffer
|
|
outOfRangeAlphaNumber(10) - Out of range alpha number
|
|
invalidOtaspActivatCode(11) - Invalid OTASP activation code
|
|
modemOffline(12) - Modem offline
|
|
modemLocked(13) - Modem locked
|
|
unsupportedFlash(14) - Unsupported flash
|
|
dialedNumberProhibited(15) - Dialed number prohibited
|
|
onlyE911Calls(16) - Only E911 calls
|
|
modemInUse(17) - Modem in use
|
|
unsupportedServiceType(18) - Unsupported service type
|
|
wrongCallType(19) - Wrong call type
|
|
invalidCommandCallState(20) - Invalid command (call state)
|
|
invalidCommandModemState(21) - Invalid command (modem state)
|
|
noValidService(22) - No valid service
|
|
cannotAnswerIncomingCall(23) - Cannot answer incoming call
|
|
badPrivacySetting(24) - Bad privacy setting
|
|
noCommandBuffers(25) - No command buffers
|
|
communicationProblem(26) - Communication problem
|
|
unspecifiedError(27) - Unspecified error
|
|
invalidLastActiveNetwork(28) - Invalid last active network
|
|
noCollocatedHdr(29) - No collocated HDR
|
|
uimNotPresent(30) - UIM (User Identity Module) not
|
|
present"
|
|
::= { c3gCdmaConnectionEntry 21 }
|
|
|
|
|
|
|
|
c3gCdmaIdentityTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaIdentityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA identity table."
|
|
::= { c3gWanCdma 3 }
|
|
|
|
c3gCdmaIdentityEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaIdentityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaIdentityTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaIdentityTable 1 }
|
|
|
|
C3gCdmaIdentityEntry ::= SEQUENCE {
|
|
c3gEsn DisplayString,
|
|
c3gModemActivationStatus INTEGER,
|
|
c3gAccountActivationDate DisplayString,
|
|
c3gCdmaRoamingPreference INTEGER,
|
|
c3gPrlVersion Unsigned32,
|
|
c3gMdn DisplayString,
|
|
c3gMsid DisplayString,
|
|
c3gMsl DisplayString
|
|
}
|
|
|
|
c3gEsn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..128))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates Electronic Serial Number (ESN)."
|
|
::= { c3gCdmaIdentityEntry 1 }
|
|
|
|
c3gModemActivationStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
activated(2),
|
|
notActivated(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Modem activation status."
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaIdentityEntry 2 }
|
|
|
|
c3gAccountActivationDate OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..128))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Modem account activation date."
|
|
::= { c3gCdmaIdentityEntry 3 }
|
|
|
|
c3gCdmaRoamingPreference OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
home(2),
|
|
affiliated(3),
|
|
any(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the roaming preference:
|
|
unknown(1) - preference unknown
|
|
home(2) - home networks only
|
|
affiliated(3) - roaming on affiliated networks
|
|
any(4) - roaming on any network"
|
|
DEFVAL { any }
|
|
::= { c3gCdmaIdentityEntry 4 }
|
|
|
|
c3gPrlVersion OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Preferred Roaming List (PRL) version."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaIdentityEntry 5 }
|
|
|
|
c3gMdn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Directory Number (MDN), a dialable number assigned to a
|
|
wireless phone."
|
|
::= { c3gCdmaIdentityEntry 6 }
|
|
|
|
c3gMsid OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Station Identifier (MSID), MSID is utilized to
|
|
distinguish the mobile station being programmed from other
|
|
mobile stations during messaging and paging processes,
|
|
including the downloading of programming information to the
|
|
mobile station."
|
|
::= { c3gCdmaIdentityEntry 7 }
|
|
|
|
c3gMsl OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Subscriber Lock (MSL)."
|
|
::= { c3gCdmaIdentityEntry 8 }
|
|
|
|
|
|
|
|
c3gCdmaNetworkTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaNetworkEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA network table."
|
|
::= { c3gWanCdma 4 }
|
|
|
|
c3gCdmaNetworkEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaNetworkEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaNetworkTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaNetworkTable 1 }
|
|
|
|
C3gCdmaNetworkEntry ::= SEQUENCE {
|
|
c3gCdmaCurrentServiceStatus DisplayString,
|
|
c3gCdmaHybridModePreference INTEGER,
|
|
c3gCdmaCurrentRoamingStatus INTEGER,
|
|
c3gCurrentIdleDigitalMode INTEGER,
|
|
c3gCurrentSid Integer32,
|
|
c3gCurrentNid Integer32,
|
|
c3gCurrentCallSetupMode INTEGER,
|
|
c3gSipUsername DisplayString,
|
|
c3gSipPassword DisplayString,
|
|
c3gServingBaseStationLongitude DisplayString,
|
|
c3gServingBaseStationLatitude DisplayString
|
|
}
|
|
|
|
c3gCdmaCurrentServiceStatus OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current service status."
|
|
::= { c3gCdmaNetworkEntry 1 }
|
|
|
|
c3gCdmaHybridModePreference OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
hybrid(2),
|
|
evDoOnly(3),
|
|
oneXRttOnly(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the hybrid mode preference:
|
|
unknown(1) - preference unknown
|
|
hybrid(2) - connect to EV-DO/1xRTT services
|
|
evDoOnly(3) - connect to only EV-DO service
|
|
oneXRttOnly(4) - connect to only 1xRTT service"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaNetworkEntry 2 }
|
|
|
|
c3gCdmaCurrentRoamingStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
home(2),
|
|
roamingWithSid(3),
|
|
roamingWithoutSid(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current 1xRTT roaming status, roaming is a general term in
|
|
wireless telecommunications that refers to the extending of
|
|
connectivity service in a location that is different from the
|
|
home location where the service was registered:
|
|
unknown(1) - roaming status is unknown.
|
|
home(2) - connectivity service in home location.
|
|
roamingWithSid(3) - roaming with SID.
|
|
roamingWithoutSid(4) - roaming without SID"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaNetworkEntry 3 }
|
|
|
|
c3gCurrentIdleDigitalMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
noService(2),
|
|
amps(3),
|
|
cdma(4),
|
|
gsm(5),
|
|
hdr(6),
|
|
wcdma(7),
|
|
gps(8),
|
|
lte(9)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current idle digital mode:
|
|
unknown(1) - service is unknown
|
|
noService(2) - no service
|
|
amps(3) - Advanced Mobile Phone Service (AMPS)
|
|
cdma(4) - Code Division Multiple Access (CDMA)
|
|
gsm(5) - Global System for Mobile communications (GSM)
|
|
hdr(6) - High Data Rate (HDR)
|
|
wcdma(7) - Wideband Code-Division Multiple-Access (WCDMA)
|
|
gps(8) - Global Positioning System (GPS)
|
|
lte(9) - Long Term Evolution (LTE)"
|
|
DEFVAL { noService }
|
|
::= { c3gCdmaNetworkEntry 4 }
|
|
|
|
c3gCurrentSid OBJECT-TYPE
|
|
SYNTAX Integer32 (-1..32767)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current System Identifier (SID), SID is a 15-bit numeric
|
|
identifiers used by cellular systems to identify the
|
|
home system of a cellular telephone and by the cellular
|
|
telephone to determine its roaming status. Value of '-1'
|
|
indicates SID is 'Not Applicable'."
|
|
::= { c3gCdmaNetworkEntry 5 }
|
|
|
|
c3gCurrentNid OBJECT-TYPE
|
|
SYNTAX Integer32 (-1..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current Network Identification (NID), NID is a 16-bit numeric
|
|
identifiers used by cellular systems. Value of '-1' indicates
|
|
NID is 'Not Applicable'."
|
|
::= { c3gCdmaNetworkEntry 6 }
|
|
|
|
c3gCurrentCallSetupMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
simpleIpOnly(2),
|
|
mobileIpPreferWithSipFallback(3),
|
|
mobileIpOnly(4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current call setup mode. The 1xEV-DO system supports packet
|
|
data connections to a public or private data network using
|
|
either mobile IP or simple IP protocol. For simple IP
|
|
protocol, moving from the coverage area of one PDSN to another
|
|
PDSN constitutes a change in packet data session. For mobile
|
|
IP protocol, a packet data session can span several PDSNs as
|
|
long as the user continuously maintains mobility bindings at
|
|
the Home Agent (the IP address is persistent). The modes are:
|
|
unknown(1) - mode is unknown
|
|
simpleIpOnly(2) - simple IP only
|
|
mobileIpPreferWithSipFallback(3) - prefer mobile IP with
|
|
simple IP as fallback mode
|
|
mobileIpOnly(4) - mobile IP only"
|
|
DEFVAL { unknown }
|
|
::= { c3gCdmaNetworkEntry 7 }
|
|
|
|
c3gSipUsername OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Simple IP (SIP) user name."
|
|
::= { c3gCdmaNetworkEntry 8 }
|
|
|
|
c3gSipPassword OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Simple IP (SIP) password."
|
|
::= { c3gCdmaNetworkEntry 9 }
|
|
|
|
c3gServingBaseStationLongitude OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Longitude of the serving base station."
|
|
::= { c3gCdmaNetworkEntry 10 }
|
|
|
|
c3gServingBaseStationLatitude OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Latitude of the serving base station."
|
|
::= { c3gCdmaNetworkEntry 11 }
|
|
|
|
|
|
c3gCdmaProfile OBJECT IDENTIFIER
|
|
::= { c3gWanCdma 5 }
|
|
|
|
|
|
c3gCdmaProfileCommonTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaProfileCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA profile common table."
|
|
::= { c3gCdmaProfile 1 }
|
|
|
|
c3gCdmaProfileCommonEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaProfileCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaProfileCommonTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaProfileCommonTable 1 }
|
|
|
|
C3gCdmaProfileCommonEntry ::= SEQUENCE {
|
|
c3gNumberOfDataProfileConfigurable Unsigned32,
|
|
c3gCurrentActiveDataProfile Unsigned32
|
|
}
|
|
|
|
c3gNumberOfDataProfileConfigurable OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of data profiles configurable."
|
|
DEFVAL { 0 }
|
|
::= { c3gCdmaProfileCommonEntry 1 }
|
|
|
|
c3gCurrentActiveDataProfile OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The current active data profile."
|
|
::= { c3gCdmaProfileCommonEntry 2 }
|
|
|
|
|
|
|
|
c3gCdmaProfileTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA profile table."
|
|
::= { c3gCdmaProfile 2 }
|
|
|
|
c3gCdmaProfileEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaProfileTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gCdmaProfileIndex
|
|
}
|
|
::= { c3gCdmaProfileTable 1 }
|
|
|
|
C3gCdmaProfileEntry ::= SEQUENCE {
|
|
c3gCdmaProfileIndex Integer32,
|
|
c3gNai DisplayString,
|
|
c3gAaaPassword DisplayString,
|
|
c3gMnHaSs INTEGER,
|
|
c3gMnHaSpi Unsigned32,
|
|
c3gMnAaaSs INTEGER,
|
|
c3gMnAaaSpi Unsigned32,
|
|
c3gReverseTunnelPreference INTEGER,
|
|
c3gHomeAddrType InetAddressType,
|
|
c3gHomeAddr InetAddress,
|
|
c3gPriHaAddrType InetAddressType,
|
|
c3gPriHaAddr InetAddress,
|
|
c3gSecHaAddrType InetAddressType,
|
|
c3gSecHaAddr InetAddress
|
|
}
|
|
|
|
c3gCdmaProfileIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Profile index, combined with entPhysicalIndex to access
|
|
the profile table c3gCdmaProfileTable."
|
|
::= { c3gCdmaProfileEntry 1 }
|
|
|
|
c3gNai OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network Access Identifier (NAI). NAI is required to identify
|
|
the mobile user and the network the mobile user intended to
|
|
access. The NAI is provided by the mobile node to the dialed
|
|
ISP during PPP authentication."
|
|
::= { c3gCdmaProfileEntry 2 }
|
|
|
|
c3gAaaPassword OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the password for AAA."
|
|
::= { c3gCdmaProfileEntry 3 }
|
|
|
|
c3gMnHaSs OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
set(1),
|
|
notSet(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Node (MN) Home Agent (HA) Shared Secret (SS) setting:
|
|
set(1) - shared secret is set
|
|
notSet(2) - shared secret is not set"
|
|
DEFVAL { notSet }
|
|
::= { c3gCdmaProfileEntry 4 }
|
|
|
|
c3gMnHaSpi OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Node (MN) Home Agent (HA) Security Parameter Index
|
|
(SPI)."
|
|
::= { c3gCdmaProfileEntry 5 }
|
|
|
|
c3gMnAaaSs OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
set(1),
|
|
notSet(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Node (MN) Authentication Authorization Accounting (AAA)
|
|
Shared Secret (SS) setting:
|
|
set(1) - shared secret is set
|
|
notSet(2) - shared secret is not set"
|
|
DEFVAL { notSet }
|
|
::= { c3gCdmaProfileEntry 6 }
|
|
|
|
c3gMnAaaSpi OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Node (MN) Authentication Authorization Accounting (AAA)
|
|
Security Parameter Index (SPI)."
|
|
::= { c3gCdmaProfileEntry 7 }
|
|
|
|
c3gReverseTunnelPreference OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
set(1),
|
|
notSet(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Reverse tunnel preference."
|
|
::= { c3gCdmaProfileEntry 8 }
|
|
|
|
c3gHomeAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A value that represents the type of the IP Address stored in
|
|
the object c3gHomeAddr."
|
|
::= { c3gCdmaProfileEntry 9 }
|
|
|
|
c3gHomeAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unicast routable address assigned to a Mobile Node, used as
|
|
the permanent address of the Mobile Node."
|
|
::= { c3gCdmaProfileEntry 10 }
|
|
|
|
c3gPriHaAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A value that represents the type of the IP Address stored in
|
|
the object c3gPriHaAddr."
|
|
::= { c3gCdmaProfileEntry 11 }
|
|
|
|
c3gPriHaAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The primary home agent address."
|
|
::= { c3gCdmaProfileEntry 12 }
|
|
|
|
c3gSecHaAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A value that represents the type of the IP Address stored in
|
|
the object c3gSecHaAddr."
|
|
::= { c3gCdmaProfileEntry 13 }
|
|
|
|
c3gSecHaAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The secondary home agent address."
|
|
::= { c3gCdmaProfileEntry 14 }
|
|
|
|
|
|
c3gCdmaRadio OBJECT IDENTIFIER
|
|
::= { c3gWanCdma 6 }
|
|
|
|
|
|
c3gCdma1xRttRadioTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdma1xRttRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA 1xRTT radio table."
|
|
::= { c3gCdmaRadio 1 }
|
|
|
|
c3gCdma1xRttRadioEntry OBJECT-TYPE
|
|
SYNTAX C3gCdma1xRttRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdma1xRttRadioTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdma1xRttRadioTable 1 }
|
|
|
|
C3gCdma1xRttRadioEntry ::= SEQUENCE {
|
|
c3gCurrent1xRttRssi C3gRssi,
|
|
c3gCurrent1xRttEcIo C3gEcIo,
|
|
c3gCurrent1xRttChannelNumber Integer32,
|
|
c3gCurrent1xRttChannelState INTEGER
|
|
}
|
|
|
|
c3gCurrent1xRttRssi OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current 1xRTT RSSI value."
|
|
::= { c3gCdma1xRttRadioEntry 1 }
|
|
|
|
c3gCurrent1xRttEcIo OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current 1xRTT Ec/Io value."
|
|
::= { c3gCdma1xRttRadioEntry 2 }
|
|
|
|
c3gCurrent1xRttChannelNumber OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current 1xRTT channel number. Current channel number to which
|
|
the modem is attached to the base station. Value of '-1'
|
|
indicates 'No Service'."
|
|
::= { c3gCdma1xRttRadioEntry 3 }
|
|
|
|
c3gCurrent1xRttChannelState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
notAcquired(2),
|
|
acquired(3),
|
|
scanning(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current 1xRTT channel state. Indicates whether the modem is
|
|
scanning or has acquired the channel."
|
|
DEFVAL { notAcquired }
|
|
::= { c3gCdma1xRttRadioEntry 4 }
|
|
|
|
|
|
|
|
c3gCdma1xRttBandClassTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdma1xRttBandClassEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA 1xRTT band class table. This table contains
|
|
band class information for each available band."
|
|
::= { c3gCdmaRadio 2 }
|
|
|
|
c3gCdma1xRttBandClassEntry OBJECT-TYPE
|
|
SYNTAX C3gCdma1xRttBandClassEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdma1xRttBandClassTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gBandClassIndex
|
|
}
|
|
::= { c3gCdma1xRttBandClassTable 1 }
|
|
|
|
C3gCdma1xRttBandClassEntry ::= SEQUENCE {
|
|
c3gBandClassIndex Integer32,
|
|
c3g1xRttBandClass Unsigned32
|
|
}
|
|
|
|
c3gBandClassIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..32)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Band class index, combined with entPhysicalIndex to access
|
|
the band class table."
|
|
::= { c3gCdma1xRttBandClassEntry 1 }
|
|
|
|
c3g1xRttBandClass OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains 1xRTT band class."
|
|
::= { c3gCdma1xRttBandClassEntry 2 }
|
|
|
|
|
|
|
|
c3gCdmaEvDoRadioTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaEvDoRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA EV-DO radio table."
|
|
::= { c3gCdmaRadio 3 }
|
|
|
|
c3gCdmaEvDoRadioEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaEvDoRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaEvDoRadioTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaEvDoRadioTable 1 }
|
|
|
|
C3gCdmaEvDoRadioEntry ::= SEQUENCE {
|
|
c3gCurrentEvDoRssi C3gRssi,
|
|
c3gCurrentEvDoEcIo C3gEcIo,
|
|
c3gCurrentEvDoChannelNumber Integer32,
|
|
c3gSectorId DisplayString,
|
|
c3gSubnetMask Unsigned32,
|
|
c3gHdrColorCode Unsigned32,
|
|
c3gPnOffset Unsigned32,
|
|
c3gRxMainGainControl Integer32,
|
|
c3gRxDiversityGainControl Integer32,
|
|
c3gTxTotalPower Integer32,
|
|
c3gTxGainAdjust Integer32,
|
|
c3gCarrierToInterferenceRatio Unsigned32
|
|
}
|
|
|
|
c3gCurrentEvDoRssi OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current EV-DO RSSI value."
|
|
::= { c3gCdmaEvDoRadioEntry 1 }
|
|
|
|
c3gCurrentEvDoEcIo OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current EV-DO Ec/Io value."
|
|
::= { c3gCdmaEvDoRadioEntry 2 }
|
|
|
|
c3gCurrentEvDoChannelNumber OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current EV-DO channel number. Current channel number to
|
|
which the modem is attached to the base station. Value of '-1'
|
|
indicates 'No Service'."
|
|
::= { c3gCdmaEvDoRadioEntry 3 }
|
|
|
|
c3gSectorId OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Sector ID of the base station to which the modem is attached."
|
|
::= { c3gCdmaEvDoRadioEntry 4 }
|
|
|
|
c3gSubnetMask OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Subnet mask of the sector, not to be confused with the IP
|
|
subnet mask."
|
|
REFERENCE "3GPP2 C.S0024-B v1.0"
|
|
::= { c3gCdmaEvDoRadioEntry 5 }
|
|
|
|
c3gHdrColorCode OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Color code of the sector."
|
|
REFERENCE "3GPP2 C.S0024-B v1.0"
|
|
::= { c3gCdmaEvDoRadioEntry 6 }
|
|
|
|
c3gPnOffset OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"PN offset. PN offset is a time offset from the beginning of
|
|
the well-known pseudo-random noise sequence that is used to
|
|
spread the signal from the base station."
|
|
REFERENCE "3GPP2 C.S0024-B v1.0"
|
|
::= { c3gCdmaEvDoRadioEntry 7 }
|
|
|
|
c3gRxMainGainControl OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Received main gain control for the modem. value of '-1'
|
|
indicates the received main gain control is unavailable."
|
|
::= { c3gCdmaEvDoRadioEntry 8 }
|
|
|
|
c3gRxDiversityGainControl OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Received diversity for the modem. value of '-1' indicates the
|
|
received diversity is unavailable."
|
|
::= { c3gCdmaEvDoRadioEntry 9 }
|
|
|
|
c3gTxTotalPower OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transmit total power."
|
|
::= { c3gCdmaEvDoRadioEntry 10 }
|
|
|
|
c3gTxGainAdjust OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Transmit gain adjust."
|
|
::= { c3gCdmaEvDoRadioEntry 11 }
|
|
|
|
c3gCarrierToInterferenceRatio OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Carrier to interference ratio. Carrier-to-Interference
|
|
ratio (C/I) is the ratio of power in an RF carrier to the
|
|
interference power in the channel."
|
|
::= { c3gCdmaEvDoRadioEntry 12 }
|
|
|
|
|
|
|
|
c3gCdmaEvDoBandClassTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaEvDoBandClassEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA EV-DO band class table. This table contains
|
|
band class information for each available band."
|
|
::= { c3gCdmaRadio 4 }
|
|
|
|
c3gCdmaEvDoBandClassEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaEvDoBandClassEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaEvDoBandClassTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gBandClassIndex
|
|
}
|
|
::= { c3gCdmaEvDoBandClassTable 1 }
|
|
|
|
C3gCdmaEvDoBandClassEntry ::= SEQUENCE {
|
|
c3gEvDoBandClass Unsigned32
|
|
}
|
|
|
|
c3gEvDoBandClass OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains EV-DO band class."
|
|
::= { c3gCdmaEvDoBandClassEntry 1 }
|
|
|
|
|
|
|
|
c3gCdmaHistoryTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaHistoryEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA history table. The history of RSSI are
|
|
carried in an octet of string. Each octet in the octet string
|
|
has a value from 0 to 150 and the 255 value is reserved to
|
|
indicate an uninitialized (Invalid) value. The format of the
|
|
octet string with n octets is as following:
|
|
[ octet 0 is latest,
|
|
octet 1 is latest-1,
|
|
.
|
|
.
|
|
octet n-2 is oldest-1,
|
|
octet n-1 is oldest ]
|
|
|
|
To convert the provided value into dBm the following formula
|
|
should be used:
|
|
dBm = (-1)*value;"
|
|
::= { c3gCdmaRadio 5 }
|
|
|
|
c3gCdmaHistoryEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaHistoryEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaHistoryTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaHistoryTable 1 }
|
|
|
|
C3gCdmaHistoryEntry ::= SEQUENCE {
|
|
c3gCdmaHistory1xRttRssiPerSecond OCTET STRING,
|
|
c3gCdmaHistory1xRttRssiPerMinute OCTET STRING,
|
|
c3gCdmaHistory1xRttRssiPerHour OCTET STRING,
|
|
c3gCdmaHistoryEvDoRssiPerSecond OCTET STRING,
|
|
c3gCdmaHistoryEvDoRssiPerMinute OCTET STRING,
|
|
c3gCdmaHistoryEvDoRssiPerHour OCTET STRING
|
|
}
|
|
|
|
c3gCdmaHistory1xRttRssiPerSecond OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-second 1xRTT RSSI history. This object contains a
|
|
per-second history of 1xRTT RSSI values for the last 60
|
|
seconds."
|
|
::= { c3gCdmaHistoryEntry 1 }
|
|
|
|
c3gCdmaHistory1xRttRssiPerMinute OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-minute 1xRTT weakest RSSI value history. This
|
|
object contains a per-minute history of 1xRTT weakest RSSI
|
|
values for the last 60 minutes. The octet in the string
|
|
is the weakest RSSI value measured in a minute interval."
|
|
::= { c3gCdmaHistoryEntry 2 }
|
|
|
|
c3gCdmaHistory1xRttRssiPerHour OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (72))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-hour 1xRTT weakest RSSI value history. This object
|
|
contains a per-hour history of 1xRTT weakest RSSI values for the
|
|
last 72 hours. The octet in the string is the weakest RSSI
|
|
value measured in an hour interval."
|
|
::= { c3gCdmaHistoryEntry 3 }
|
|
|
|
c3gCdmaHistoryEvDoRssiPerSecond OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-second EV-DO RSSI history. This object contains a
|
|
per-second history of EV-DO RSSI values for the last 60
|
|
seconds."
|
|
::= { c3gCdmaHistoryEntry 4 }
|
|
|
|
c3gCdmaHistoryEvDoRssiPerMinute OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-minute EV-DO weakest RSSI value history. This
|
|
object contains a per-minute history of EV-DO weakest RSSI
|
|
values for the last 60 minutes. The octet in the string is the
|
|
weakest RSSI value measured in a minute interval."
|
|
::= { c3gCdmaHistoryEntry 5 }
|
|
|
|
c3gCdmaHistoryEvDoRssiPerHour OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (72))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-hour EV-DO weakest RSSI value history. This object
|
|
contains a per-hour history of EV-DO weakest RSSI values for the
|
|
last 72 hours. The octet in the string is the weakest RSSI
|
|
value measured in an hour interval."
|
|
::= { c3gCdmaHistoryEntry 6 }
|
|
|
|
|
|
c3gCdmaSecurity OBJECT IDENTIFIER
|
|
::= { c3gWanCdma 7 }
|
|
|
|
|
|
c3gCdmaSecurityTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gCdmaSecurityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G CDMA security table."
|
|
::= { c3gCdmaSecurity 1 }
|
|
|
|
c3gCdmaSecurityEntry OBJECT-TYPE
|
|
SYNTAX C3gCdmaSecurityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gCdmaSecurityTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gCdmaSecurityTable 1 }
|
|
|
|
C3gCdmaSecurityEntry ::= SEQUENCE {
|
|
c3gCdmaPinSecurityStatus INTEGER,
|
|
c3gCdmaPowerUpLockStatus INTEGER
|
|
}
|
|
|
|
c3gCdmaPinSecurityStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
locked(2),
|
|
unlocked(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"CDMA Personal Identification Number (PIN) security:
|
|
unknown(1) - PIN security unknown
|
|
locked(2) - PIN security is locked
|
|
unlocked(3) - PIN security is unlocked"
|
|
DEFVAL { unlocked }
|
|
::= { c3gCdmaSecurityEntry 1 }
|
|
|
|
c3gCdmaPowerUpLockStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
enabled(2),
|
|
disabled(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"CDMA power up lock:
|
|
unknown(1) - power up lock unknown
|
|
enabled(2) - power up lock enabled
|
|
disabled(3) - power up lock disabled"
|
|
DEFVAL { disabled }
|
|
::= { c3gCdmaSecurityEntry 2 }
|
|
|
|
|
|
|
|
c3gGsmIdentityTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmIdentityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"."
|
|
::= { c3gWanGsm 1 }
|
|
|
|
c3gGsmIdentityEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmIdentityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmIdentityTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gGsmIdentityTable 1 }
|
|
|
|
C3gGsmIdentityEntry ::= SEQUENCE {
|
|
c3gImsi DisplayString,
|
|
c3gImei DisplayString,
|
|
c3gIccId DisplayString,
|
|
c3gMsisdn DisplayString,
|
|
c3gFsn DisplayString,
|
|
c3gModemStatus INTEGER,
|
|
c3gGsmRoamingPreference INTEGER
|
|
}
|
|
|
|
c3gImsi OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"International Mobile Subscriber Identifier (IMSI), a unique
|
|
15-digit code used to identify an individual user on a GSM/LTE
|
|
network."
|
|
::= { c3gGsmIdentityEntry 1 }
|
|
|
|
c3gImei OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"International Mobile Equipment Identifier (IMEI), a unique 15
|
|
or 17 digit code used to identify an individual mobile station
|
|
to a GSM, UMTS or LTE network."
|
|
::= { c3gGsmIdentityEntry 2 }
|
|
|
|
c3gIccId OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the Integrated Circuit Card ID (ICCID).
|
|
The ICCID is defined by the ITU-T recommendation E.118.
|
|
ICCIDs are stored in the SIM cards and are also engraved or
|
|
printed on the SIM card body during a process called
|
|
personalization."
|
|
::= { c3gGsmIdentityEntry 3 }
|
|
|
|
c3gMsisdn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the Mobile Subscriber Integrated Services
|
|
Digital Network Number (MSISDN). It is a number uniquely
|
|
identifying a subscription in a GSM, UMTS or LTE mobile
|
|
network. It represents the telephone number to the SIM
|
|
card in a mobile/cellular phone."
|
|
::= { c3gGsmIdentityEntry 4 }
|
|
|
|
c3gFsn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Forward Sequence Number (FSN), a message acknowledgement
|
|
method using sequence number in the forward direction."
|
|
::= { c3gGsmIdentityEntry 5 }
|
|
|
|
c3gModemStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
offLine(2),
|
|
onLine(3),
|
|
lowPowerMode(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Modem status:
|
|
unknown(1) - modem status is unknown
|
|
offLine(2) - modem is off line
|
|
onLine(3) - modem is on line
|
|
lowPowerMode(4) - modem is in the low power mode"
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmIdentityEntry 6 }
|
|
|
|
c3gGsmRoamingPreference OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
home(2),
|
|
roaming(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the roaming preference."
|
|
::= { c3gGsmIdentityEntry 7 }
|
|
|
|
|
|
|
|
c3gGsmNetworkTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmNetworkEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular GSM Network table. This table is applicable in both
|
|
3G and 4G-LTE technology mode"
|
|
::= { c3gWanGsm 2 }
|
|
|
|
c3gGsmNetworkEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmNetworkEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmNetworkTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gGsmNetworkTable 1 }
|
|
|
|
C3gGsmNetworkEntry ::= SEQUENCE {
|
|
c3gGsmLac Unsigned32,
|
|
c3gGsmCurrentServiceStatus INTEGER,
|
|
c3gGsmCurrentServiceError INTEGER,
|
|
c3gGsmCurrentService INTEGER,
|
|
c3gGsmPacketService INTEGER,
|
|
c3gGsmCurrentRoamingStatus INTEGER,
|
|
c3gGsmNetworkSelectionMode INTEGER,
|
|
c3gGsmCountry DisplayString,
|
|
c3gGsmNetwork DisplayString,
|
|
c3gGsmMcc Integer32,
|
|
c3gGsmMnc Integer32,
|
|
c3gGsmRac Unsigned32,
|
|
c3gGsmCurrentCellId Unsigned32,
|
|
c3gGsmCurrentPrimaryScramblingCode Unsigned32,
|
|
c3gGsmPlmnSelection INTEGER,
|
|
c3gGsmRegPlmn DisplayString,
|
|
c3gGsmPlmnAbbr DisplayString,
|
|
c3gGsmServiceProvider DisplayString,
|
|
c3gGsmTotalByteTransmitted Counter64,
|
|
c3gGsmTotalByteReceived Counter64
|
|
}
|
|
|
|
c3gGsmLac OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location Area Code (LAC), also called as Tracking
|
|
Area Code (TAC) in LTE standard. LAC/TAC is given
|
|
by the base station."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 1 }
|
|
|
|
c3gGsmCurrentServiceStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
noService(2),
|
|
normal(3),
|
|
emergencyOnly(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current Service Status:
|
|
unknown(1) - current service status is unknown
|
|
noService(2) - no service
|
|
normal(3) - service status is normal
|
|
emergencyOnly(4) - emergency service only"
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmNetworkEntry 2 }
|
|
|
|
c3gGsmCurrentServiceError OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
none(2),
|
|
imsiUnknownInHlr(3),
|
|
illegalMs(4),
|
|
imsiUnknownInVlr(5),
|
|
imeiNotAccepted(6),
|
|
illegalMe(7),
|
|
gprsServNotAllowed(8),
|
|
gprsNonGprsServNotAllow(9),
|
|
msIdentUnknown(10),
|
|
implicitlyDetached(11),
|
|
plmnNotAllowed(12),
|
|
lacNotAllowed(13),
|
|
roamingNotAllowed(14),
|
|
gprsServNotAllowInPlmn(15),
|
|
noSuitableCellInLa(16),
|
|
mscTempNotReachable(17),
|
|
networkFailure(18),
|
|
macFailure(19),
|
|
synchFailure(20),
|
|
congestion(21),
|
|
gsmAuthenNotAccept(22),
|
|
servOptionNotSupport(23),
|
|
reqServOptionNotSub(24),
|
|
servOptionOutOfOrder(25),
|
|
callCannotIdentified(26),
|
|
noPdpContextActivated(27),
|
|
invalidMandatInfo(28),
|
|
unpsecProtErr(29)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current service error:
|
|
unknown(1) - Unknown
|
|
none(2) - None
|
|
imsiUnknownInHlr(3) - IMSI unknown in HLR (Home
|
|
Location Register)
|
|
illegalMs(4) - Illegal MS (Mobile Station)
|
|
imsiUnknownInVlr(5) - IMSI unknown in VLR (Visitor
|
|
Location Register)
|
|
imeiNotAccepted(6) - IMEI not accepted
|
|
illegalMe(7) - Illegal ME (Mobile Entity)
|
|
gprsServNotAllowed(8) - GPRS services not allowed
|
|
gprsNonGprsServNotAllow(9) - GPRS and non-GPRS services
|
|
not allowed
|
|
msIdentUnknown(10) - MS identity unknown
|
|
implicitlyDetached(11) - Implicitly detached
|
|
plmnNotAllowed(12) - PLMN not allowed
|
|
lacNotAllowed(13) - LAC not allowed
|
|
roamingNotAllowed(14) - Roaming not allowed
|
|
gprsServNotAllowInPlmn(15) - GPRS services not allowed
|
|
in this PLMN
|
|
noSuitableCellInLa(16) - No suitable cells in LA (Location
|
|
Area)
|
|
mscTempNotReachable(17) - MSC (Mobile Switching Center)
|
|
temporarily not reachable
|
|
networkFailure(18) - Network failure
|
|
macFailure(19) - MAC failure
|
|
synchFailure(20) - Synch failure
|
|
congestion(21) - Congestion
|
|
gsmAuthenNotAccept(22) - GSM/LTE Authentication not accepted
|
|
servOptionNotSupport(23) - Service option not supported
|
|
reqServOptionNotSub(24) - Requested service option not
|
|
subscribed
|
|
servOptionOutOfOrder(25) - Service option out of order
|
|
callCannotIdentified(26) - Call cannot be identified
|
|
noPdpContextActivated(27) - No PDP context activated
|
|
invalidMandatInfo(28) - Invalid mandatory info
|
|
unpsecProtErr(29) - Unspecified protocol error"
|
|
::= { c3gGsmNetworkEntry 3 }
|
|
|
|
c3gGsmCurrentService OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
invalid(2),
|
|
circuitSwitched(3),
|
|
packetSwitched(4),
|
|
combined(5)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current service type:
|
|
unknown(1) - service type is unknown
|
|
invalid(2) - no service
|
|
circuitSwitched(3) - circuit switched service
|
|
packetSwitched(4) - packet switched service
|
|
combined(5) - combination of circuit and packet
|
|
switched service"
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmNetworkEntry 4 }
|
|
|
|
c3gGsmPacketService OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
none(2),
|
|
gprs(3),
|
|
edge(4),
|
|
umtsWcdma(5),
|
|
hsdpa(6),
|
|
hsupa(7),
|
|
hspa(8),
|
|
hspaPlus(9),
|
|
lte(10)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Packet Service type:
|
|
unknown(1) - service type is unknown.
|
|
none(2) - no service.
|
|
gprs(3) - General Packet Radio Service (GPRS).
|
|
edge(4) - Enhanced Data rates for GSM Evolution (EDGE).
|
|
umtsWcdma(5) - Universal Mobile Telecommunications
|
|
System (UMTS) / Wideband Code-Division
|
|
Multiple-Access (W-CDMA).
|
|
hsdpa(6) - High-Speed Downlink Packet Access (HSDPA)
|
|
hsdpa(7) - High-Speed Uplink Packet Access (HSUPA)
|
|
hspa(8) - High-Speed Packet Access (HSPA)
|
|
hspaPlus(9) - High-Speed Packet Access (HSPA) Plus
|
|
lte(10) - Long Term Evolution"
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmNetworkEntry 5 }
|
|
|
|
c3gGsmCurrentRoamingStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
roaming(2),
|
|
home(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether the modem is in the home network
|
|
or is roaming."
|
|
DEFVAL { home }
|
|
::= { c3gGsmNetworkEntry 6 }
|
|
|
|
c3gGsmNetworkSelectionMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
automatic(2),
|
|
manual(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network selection mode. Can be manual selection mode or
|
|
automatic selection mode. Set to automatic by default."
|
|
DEFVAL { automatic }
|
|
::= { c3gGsmNetworkEntry 7 }
|
|
|
|
c3gGsmCountry OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Country code. Country code string is given by the base
|
|
station."
|
|
::= { c3gGsmNetworkEntry 8 }
|
|
|
|
c3gGsmNetwork OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network code. Network Code string is given by the base
|
|
station."
|
|
::= { c3gGsmNetworkEntry 9 }
|
|
|
|
c3gGsmMcc OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Country Code (MCC). Value of '-1' indicates MCC is 'Not
|
|
Applicable'."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 10 }
|
|
|
|
c3gGsmMnc OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mobile Network Code (MNC). Value of '-1' indicates MNC is 'Not
|
|
Applicable'."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 11 }
|
|
|
|
c3gGsmRac OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Routing Area Code (RAC). RAC is given by the base station."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 12 }
|
|
|
|
c3gGsmCurrentCellId OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cell Identifier of current cell. Cell ID is given by the
|
|
base station."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 13 }
|
|
|
|
c3gGsmCurrentPrimaryScramblingCode OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Primary scrambling code of current cell. The primary
|
|
scrambling code is typically identified through
|
|
symbol-by-symbol correlation over the CPICH (Common Pilot
|
|
Channel) with all codes within the code group, after the
|
|
primary scrambling code has been identified,
|
|
the Primary CCPCH can be detected and the system and cell
|
|
specific BCH information can be read."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmNetworkEntry 14 }
|
|
|
|
c3gGsmPlmnSelection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
manual(2),
|
|
automatic(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Public Land Mobile Network (PLMN) selection. Can be manual
|
|
selection mode or automatic selection mode. Set to automatic by
|
|
default."
|
|
DEFVAL { automatic }
|
|
::= { c3gGsmNetworkEntry 15 }
|
|
|
|
c3gGsmRegPlmn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Registered PLMN."
|
|
::= { c3gGsmNetworkEntry 16 }
|
|
|
|
c3gGsmPlmnAbbr OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"PLMN abbreviated number."
|
|
::= { c3gGsmNetworkEntry 17 }
|
|
|
|
c3gGsmServiceProvider OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Service provider."
|
|
::= { c3gGsmNetworkEntry 18 }
|
|
|
|
c3gGsmTotalByteTransmitted OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Total number of bytes transmitted for all calls. It is the
|
|
total number of bytes transmitted by modem, not to be confused
|
|
with the number of bytes transmitted through the interface."
|
|
::= { c3gGsmNetworkEntry 19 }
|
|
|
|
c3gGsmTotalByteReceived OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Total number of bytes received for all calls. It is the total
|
|
number of bytes received by modem, not to be confused with the
|
|
number of bytes received from the interface."
|
|
::= { c3gGsmNetworkEntry 20 }
|
|
|
|
|
|
c3gGsmPdpProfile OBJECT IDENTIFIER
|
|
::= { c3gWanGsm 3 }
|
|
|
|
|
|
c3gGsmPdpProfileTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmPdpProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular GSM PDP profiles table. Cellular device contains
|
|
multiple profile entries which can be used to establish
|
|
cellular data connections (PDP contexts). Users can choose
|
|
any of available PDP profiles to establish data connections.
|
|
Data connections are described in c3gGsmPacketSessionTable.
|
|
This table is applicable in only 3G technology mode. Refer
|
|
CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode."
|
|
::= { c3gGsmPdpProfile 1 }
|
|
|
|
c3gGsmPdpProfileEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmPdpProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmPdpProfileTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmPdpProfileTable 1 }
|
|
|
|
C3gGsmPdpProfileEntry ::= SEQUENCE {
|
|
c3gGsmPdpProfileIndex Integer32,
|
|
c3gGsmPdpProfileType C3gPdpType,
|
|
c3gGsmPdpProfileAddr DisplayString,
|
|
c3gGsmPdpProfileApn DisplayString,
|
|
c3gGsmPdpProfileAuthenType INTEGER,
|
|
c3gGsmPdpProfileUsername DisplayString,
|
|
c3gGsmPdpProfilePassword DisplayString,
|
|
c3gGsmPdpProfileRowStatus RowStatus
|
|
}
|
|
|
|
c3gGsmPdpProfileIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..1000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Profile index, combined with entPhysicalIndex to
|
|
access profile table."
|
|
::= { c3gGsmPdpProfileEntry 1 }
|
|
|
|
c3gGsmPdpProfileType OBJECT-TYPE
|
|
SYNTAX C3gPdpType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates configured Packet Data Protocol (PDP)
|
|
type."
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmPdpProfileEntry 2 }
|
|
|
|
c3gGsmPdpProfileAddr OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configured PDP/EPS Bearer address. PDP type is
|
|
defined in c3gGsmPdpProfileType."
|
|
::= { c3gGsmPdpProfileEntry 3 }
|
|
|
|
c3gGsmPdpProfileApn OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates profile Access Point Name (APN). This
|
|
information is provided by the service provider."
|
|
::= { c3gGsmPdpProfileEntry 4 }
|
|
|
|
c3gGsmPdpProfileAuthenType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
none(2),
|
|
chap(3),
|
|
pap(4)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates PDP authentication type
|
|
supported. CHAP and PAP are supported in GSM. The type of
|
|
authentication to be used is provided by the service
|
|
provider."
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmPdpProfileEntry 5 }
|
|
|
|
c3gGsmPdpProfileUsername OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the username to be used for PDP
|
|
authentication. This information is provided by the service
|
|
provider."
|
|
::= { c3gGsmPdpProfileEntry 6 }
|
|
|
|
c3gGsmPdpProfilePassword OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the password to be used for PDP
|
|
authentication. This information is provided by the service
|
|
provider."
|
|
::= { c3gGsmPdpProfileEntry 7 }
|
|
|
|
c3gGsmPdpProfileRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gGsmPdpProfileEntry 8 }
|
|
|
|
|
|
|
|
c3gGsmPacketSessionTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmPacketSessionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G GSM packet session table. This table is applicable
|
|
in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
|
|
when in 4G-LTE mode."
|
|
::= { c3gGsmPdpProfile 2 }
|
|
|
|
c3gGsmPacketSessionEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmPacketSessionEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmPacketSessionTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmPacketSessionTable 1 }
|
|
|
|
C3gGsmPacketSessionEntry ::= SEQUENCE {
|
|
c3gGsmPacketSessionStatus INTEGER,
|
|
c3gGsmPdpType C3gPdpType,
|
|
c3gGsmPdpAddress DisplayString
|
|
}
|
|
|
|
c3gGsmPacketSessionStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
active(2),
|
|
inactive(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates PDP session status
|
|
of the profile. This is active when the call is established
|
|
and PDP contextr has become active."
|
|
DEFVAL { inactive }
|
|
::= { c3gGsmPacketSessionEntry 1 }
|
|
|
|
c3gGsmPdpType OBJECT-TYPE
|
|
SYNTAX C3gPdpType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates current session PDP type."
|
|
::= { c3gGsmPacketSessionEntry 2 }
|
|
|
|
c3gGsmPdpAddress OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..64))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Current session PDP context/EPS Bearer address. PDP type is
|
|
obtained from c3gGsmPdpType."
|
|
::= { c3gGsmPacketSessionEntry 3 }
|
|
|
|
|
|
|
|
c3gGsmReqUmtsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmReqUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Requested UMTS QoS parameters table. This table contains UMTS
|
|
QoS parameters requested by modem to the cellular network
|
|
via PDP Context Activation Request message. The requested UMTS
|
|
QoS profile is optional. This table is applicable only in 3G
|
|
technology mode."
|
|
::= { c3gGsmPdpProfile 3 }
|
|
|
|
c3gGsmReqUmtsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmReqUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmReqUmtsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmReqUmtsQosTable 1 }
|
|
|
|
C3gGsmReqUmtsQosEntry ::= SEQUENCE {
|
|
c3gGsmReqUmtsQosTrafficClass C3gUmtsQosTrafficClass,
|
|
c3gGsmReqUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmReqUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmReqUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmReqUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmReqUmtsQosOrder C3gUmtsQosOrder,
|
|
c3gGsmReqUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
|
|
c3gGsmReqUmtsQosMaxSduSize Unsigned32,
|
|
c3gGsmReqUmtsQosSer C3gUmtsQosSer,
|
|
c3gGsmReqUmtsQosBer C3gUmtsQosBer,
|
|
c3gGsmReqUmtsQosDelay Unsigned32,
|
|
c3gGsmReqUmtsQosPriority C3gUmtsQosPriority,
|
|
c3gGsmReqUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
|
|
c3gGsmReqUmtsQosSignalIndication C3gUmtsQosSignalIndication,
|
|
c3gGsmReqUmtsQosRowStatus RowStatus
|
|
}
|
|
|
|
c3gGsmReqUmtsQosTrafficClass OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosTrafficClass
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS traffic classes."
|
|
::= { c3gGsmReqUmtsQosEntry 2 }
|
|
|
|
c3gGsmReqUmtsQosMaxUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS maximum uplink bit rate."
|
|
::= { c3gGsmReqUmtsQosEntry 3 }
|
|
|
|
c3gGsmReqUmtsQosMaxDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS maximum downlink bit rate."
|
|
::= { c3gGsmReqUmtsQosEntry 4 }
|
|
|
|
c3gGsmReqUmtsQosGuaUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS guaranteed uplink bit rate."
|
|
::= { c3gGsmReqUmtsQosEntry 5 }
|
|
|
|
c3gGsmReqUmtsQosGuaDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS guaranteed downlink bit rate."
|
|
::= { c3gGsmReqUmtsQosEntry 6 }
|
|
|
|
c3gGsmReqUmtsQosOrder OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosOrder
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS deliver order."
|
|
::= { c3gGsmReqUmtsQosEntry 7 }
|
|
|
|
c3gGsmReqUmtsQosErroneousSdu OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosErroneousSdu
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS Delivery of Erroneous SDU."
|
|
::= { c3gGsmReqUmtsQosEntry 8 }
|
|
|
|
c3gGsmReqUmtsQosMaxSduSize OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..1520)
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS maximum SDU size, the valid range is between 1
|
|
and 1520 bytes. Value of '0' indicates the maximum SDU size is
|
|
unspecified."
|
|
::= { c3gGsmReqUmtsQosEntry 9 }
|
|
|
|
c3gGsmReqUmtsQosSer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSer
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS SDU error ratio."
|
|
::= { c3gGsmReqUmtsQosEntry 10 }
|
|
|
|
c3gGsmReqUmtsQosBer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosBer
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS residual bit error ratio."
|
|
::= { c3gGsmReqUmtsQosEntry 11 }
|
|
|
|
c3gGsmReqUmtsQosDelay OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4000)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS transfer delay in ms, the valid range
|
|
is between 1 and 4000 ms. Value of '0' indicates the
|
|
QoS delay is unspecified."
|
|
::= { c3gGsmReqUmtsQosEntry 12 }
|
|
|
|
c3gGsmReqUmtsQosPriority OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosPriority
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS traffic handling priority."
|
|
::= { c3gGsmReqUmtsQosEntry 13 }
|
|
|
|
c3gGsmReqUmtsQosSrcStatDescriptor OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSrcStatDescriptor
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS source statistics descriptor."
|
|
::= { c3gGsmReqUmtsQosEntry 14 }
|
|
|
|
c3gGsmReqUmtsQosSignalIndication OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSignalIndication
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request UMTS QoS signalling indication."
|
|
::= { c3gGsmReqUmtsQosEntry 15 }
|
|
|
|
c3gGsmReqUmtsQosRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gGsmReqUmtsQosEntry 16 }
|
|
|
|
|
|
|
|
c3gGsmMinUmtsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmMinUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum acceptable UMTS QoS table. This table contains minimum
|
|
acceptable UMTS QoS parameters which is checked by the MT
|
|
(Mobile Termination) against the negotiated profile returned in
|
|
the Activate PDP Context Accept message. The minimum acceptable
|
|
UMTS QoS profile is optional. This table is applicable only in
|
|
3G technology mode."
|
|
::= { c3gGsmPdpProfile 4 }
|
|
|
|
c3gGsmMinUmtsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmMinUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmMinUmtsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmMinUmtsQosTable 1 }
|
|
|
|
C3gGsmMinUmtsQosEntry ::= SEQUENCE {
|
|
c3gGsmMinUmtsQosTrafficClass C3gUmtsQosTrafficClass,
|
|
c3gGsmMinUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmMinUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmMinUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmMinUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmMinUmtsQosOrder C3gUmtsQosOrder,
|
|
c3gGsmMinUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
|
|
c3gGsmMinUmtsQosMaxSduSize Unsigned32,
|
|
c3gGsmMinUmtsQosSer C3gUmtsQosSer,
|
|
c3gGsmMinUmtsQosBer C3gUmtsQosBer,
|
|
c3gGsmMinUmtsQosDelay Unsigned32,
|
|
c3gGsmMinUmtsQosPriority C3gUmtsQosPriority,
|
|
c3gGsmMinUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
|
|
c3gGsmMinUmtsQosSignalIndication C3gUmtsQosSignalIndication,
|
|
c3gGsmMinUmtsQosRowStatus RowStatus
|
|
}
|
|
|
|
c3gGsmMinUmtsQosTrafficClass OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosTrafficClass
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS traffic classes."
|
|
::= { c3gGsmMinUmtsQosEntry 1 }
|
|
|
|
c3gGsmMinUmtsQosMaxUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS maximum uplink bit rate."
|
|
::= { c3gGsmMinUmtsQosEntry 2 }
|
|
|
|
c3gGsmMinUmtsQosMaxDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS maximum downlink bit rate."
|
|
::= { c3gGsmMinUmtsQosEntry 3 }
|
|
|
|
c3gGsmMinUmtsQosGuaUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS guaranteed uplink bit rate."
|
|
::= { c3gGsmMinUmtsQosEntry 4 }
|
|
|
|
c3gGsmMinUmtsQosGuaDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS guaranteed downlink bit rate."
|
|
::= { c3gGsmMinUmtsQosEntry 5 }
|
|
|
|
c3gGsmMinUmtsQosOrder OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosOrder
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS deliver order."
|
|
::= { c3gGsmMinUmtsQosEntry 6 }
|
|
|
|
c3gGsmMinUmtsQosErroneousSdu OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosErroneousSdu
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS Delivery of Erroneous SDU."
|
|
::= { c3gGsmMinUmtsQosEntry 7 }
|
|
|
|
c3gGsmMinUmtsQosMaxSduSize OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..1520)
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS maximum SDU size, the valid range is between 1 and
|
|
1520 bytes. Value of '0' indicates the maximum SDU size is
|
|
unspecified."
|
|
::= { c3gGsmMinUmtsQosEntry 8 }
|
|
|
|
c3gGsmMinUmtsQosSer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSer
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS SDU error ratio."
|
|
::= { c3gGsmMinUmtsQosEntry 9 }
|
|
|
|
c3gGsmMinUmtsQosBer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosBer
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS residual bit error ratio."
|
|
::= { c3gGsmMinUmtsQosEntry 10 }
|
|
|
|
c3gGsmMinUmtsQosDelay OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4000)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS transfer delay in ms, the valid range
|
|
is between 1 and 4000 ms. Value of '0' indicates the
|
|
QoS delay is unspecified."
|
|
::= { c3gGsmMinUmtsQosEntry 11 }
|
|
|
|
c3gGsmMinUmtsQosPriority OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosPriority
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS traffic handling priority."
|
|
::= { c3gGsmMinUmtsQosEntry 12 }
|
|
|
|
c3gGsmMinUmtsQosSrcStatDescriptor OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSrcStatDescriptor
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS source statistics descriptor."
|
|
::= { c3gGsmMinUmtsQosEntry 13 }
|
|
|
|
c3gGsmMinUmtsQosSignalIndication OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSignalIndication
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum UMTS QoS signalling indication."
|
|
::= { c3gGsmMinUmtsQosEntry 14 }
|
|
|
|
c3gGsmMinUmtsQosRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gGsmMinUmtsQosEntry 15 }
|
|
|
|
|
|
|
|
c3gGsmNegoUmtsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmNegoUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS table. This table contains negotiated UMTS
|
|
QoS parameters returned in the Activate PDP Context Accept
|
|
message. The objects in this table are valid only if the value
|
|
of object c3gGsmPacketSessionStatus defined in
|
|
c3gGsmPacketSessionTable is 'active'. This table is applicable
|
|
only in 3G technology mode."
|
|
::= { c3gGsmPdpProfile 5 }
|
|
|
|
c3gGsmNegoUmtsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmNegoUmtsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmNegoUmtsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmNegoUmtsQosTable 1 }
|
|
|
|
C3gGsmNegoUmtsQosEntry ::= SEQUENCE {
|
|
c3gGsmNegoUmtsQosTrafficClass C3gUmtsQosTrafficClass,
|
|
c3gGsmNegoUmtsQosMaxUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmNegoUmtsQosMaxDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmNegoUmtsQosGuaUpLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmNegoUmtsQosGuaDownLinkBitRate C3gUmtsQosLinkBitRate,
|
|
c3gGsmNegoUmtsQosOrder C3gUmtsQosOrder,
|
|
c3gGsmNegoUmtsQosErroneousSdu C3gUmtsQosErroneousSdu,
|
|
c3gGsmNegoUmtsQosMaxSduSize Unsigned32,
|
|
c3gGsmNegoUmtsQosSer C3gUmtsQosSer,
|
|
c3gGsmNegoUmtsQosBer C3gUmtsQosBer,
|
|
c3gGsmNegoUmtsQosDelay Unsigned32,
|
|
c3gGsmNegoUmtsQosPriority C3gUmtsQosPriority,
|
|
c3gGsmNegoUmtsQosSrcStatDescriptor C3gUmtsQosSrcStatDescriptor,
|
|
c3gGsmNegoUmtsQosSignalIndication C3gUmtsQosSignalIndication
|
|
}
|
|
|
|
c3gGsmNegoUmtsQosTrafficClass OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosTrafficClass
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS traffic classes."
|
|
::= { c3gGsmNegoUmtsQosEntry 1 }
|
|
|
|
c3gGsmNegoUmtsQosMaxUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS maximum uplink bit rate."
|
|
::= { c3gGsmNegoUmtsQosEntry 2 }
|
|
|
|
c3gGsmNegoUmtsQosMaxDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS maximum downlink bit rate."
|
|
::= { c3gGsmNegoUmtsQosEntry 3 }
|
|
|
|
c3gGsmNegoUmtsQosGuaUpLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS guaranteed uplink bit rate."
|
|
::= { c3gGsmNegoUmtsQosEntry 4 }
|
|
|
|
c3gGsmNegoUmtsQosGuaDownLinkBitRate OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosLinkBitRate
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS guaranteed downlink bit rate."
|
|
::= { c3gGsmNegoUmtsQosEntry 5 }
|
|
|
|
c3gGsmNegoUmtsQosOrder OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosOrder
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS deliver order."
|
|
::= { c3gGsmNegoUmtsQosEntry 6 }
|
|
|
|
c3gGsmNegoUmtsQosErroneousSdu OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosErroneousSdu
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS Delivery of Erroneous SDU."
|
|
::= { c3gGsmNegoUmtsQosEntry 7 }
|
|
|
|
c3gGsmNegoUmtsQosMaxSduSize OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..1520)
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS maximum SDU size, the valid range is
|
|
between 1 and 1520 bytes. Value of '0' indicates the maximum
|
|
SDU size is subscribed."
|
|
::= { c3gGsmNegoUmtsQosEntry 8 }
|
|
|
|
c3gGsmNegoUmtsQosSer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSer
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS SDU error ratio."
|
|
::= { c3gGsmNegoUmtsQosEntry 9 }
|
|
|
|
c3gGsmNegoUmtsQosBer OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosBer
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS residual bit error ratio."
|
|
::= { c3gGsmNegoUmtsQosEntry 10 }
|
|
|
|
c3gGsmNegoUmtsQosDelay OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4000)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS transfer delay in ms, the valid range
|
|
is between 1 and 4000 ms. Value of '0' indicates the
|
|
QoS delay is subscribed."
|
|
::= { c3gGsmNegoUmtsQosEntry 11 }
|
|
|
|
c3gGsmNegoUmtsQosPriority OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosPriority
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS traffic handling priority."
|
|
::= { c3gGsmNegoUmtsQosEntry 12 }
|
|
|
|
c3gGsmNegoUmtsQosSrcStatDescriptor OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSrcStatDescriptor
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS source statistics descriptor."
|
|
::= { c3gGsmNegoUmtsQosEntry 13 }
|
|
|
|
c3gGsmNegoUmtsQosSignalIndication OBJECT-TYPE
|
|
SYNTAX C3gUmtsQosSignalIndication
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated UMTS QoS signalling indication."
|
|
::= { c3gGsmNegoUmtsQosEntry 14 }
|
|
|
|
|
|
|
|
c3gGsmReqGprsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmReqGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Requested GPRS QoS parameters table. This table contains GPRS
|
|
QoS parameters requested by modem to the cellular network
|
|
via PDP Context Request message. The requested GPRS QoS
|
|
profile is optional. This table is applicable only in
|
|
3G technology mode."
|
|
::= { c3gGsmPdpProfile 6 }
|
|
|
|
c3gGsmReqGprsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmReqGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmReqGprsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmReqGprsQosTable 1 }
|
|
|
|
C3gGsmReqGprsQosEntry ::= SEQUENCE {
|
|
c3gGsmReqGprsQosPrecedence C3gGprsQosPrecedence,
|
|
c3gGsmReqGprsQosDelay C3gGprsQosDelay,
|
|
c3gGsmReqGprsQosReliability C3gGprsQosReliability,
|
|
c3gGsmReqGprsQosPeakRate C3gGprsQosPeakRate,
|
|
c3gGsmReqGprsQosMeanRate C3gGprsQosMeanRate,
|
|
c3gGsmReqGprsQosRowStatus RowStatus
|
|
}
|
|
|
|
c3gGsmReqGprsQosPrecedence OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPrecedence
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request GPRS QoS precedence."
|
|
::= { c3gGsmReqGprsQosEntry 1 }
|
|
|
|
c3gGsmReqGprsQosDelay OBJECT-TYPE
|
|
SYNTAX C3gGprsQosDelay
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request GPRS QoS delay classes."
|
|
::= { c3gGsmReqGprsQosEntry 2 }
|
|
|
|
c3gGsmReqGprsQosReliability OBJECT-TYPE
|
|
SYNTAX C3gGprsQosReliability
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request GPRS QoS reliability."
|
|
::= { c3gGsmReqGprsQosEntry 3 }
|
|
|
|
c3gGsmReqGprsQosPeakRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPeakRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request GPRS QoS peak rate."
|
|
::= { c3gGsmReqGprsQosEntry 4 }
|
|
|
|
c3gGsmReqGprsQosMeanRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosMeanRate
|
|
UNITS "octet-per-hour"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Request GPRS QoS mean rate."
|
|
::= { c3gGsmReqGprsQosEntry 5 }
|
|
|
|
c3gGsmReqGprsQosRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gGsmReqGprsQosEntry 6 }
|
|
|
|
|
|
|
|
c3gGsmMinGprsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmMinGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum acceptable GPRS QoS table. This table contains minimum
|
|
acceptable GPRS QoS parameters which is checked by the MT
|
|
(Mobile Termination) against the negotiated profile returned in
|
|
the Activate PDP Context Accept message. The minimum acceptable
|
|
GPRS QoS profile is optional. This table is applicable only in
|
|
3G technology mode."
|
|
::= { c3gGsmPdpProfile 7 }
|
|
|
|
c3gGsmMinGprsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmMinGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmMinGprsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmMinGprsQosTable 1 }
|
|
|
|
C3gGsmMinGprsQosEntry ::= SEQUENCE {
|
|
c3gGsmMinGprsQosPrecedence C3gGprsQosPrecedence,
|
|
c3gGsmMinGprsQosDelay C3gGprsQosDelay,
|
|
c3gGsmMinGprsQosReliability C3gGprsQosReliability,
|
|
c3gGsmMinGprsQosPeakRate C3gGprsQosPeakRate,
|
|
c3gGsmMinGprsQosMeanRate C3gGprsQosMeanRate,
|
|
c3gGsmMinGprsQosRowStatus RowStatus
|
|
}
|
|
|
|
c3gGsmMinGprsQosPrecedence OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPrecedence
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum GPRS QoS precedence."
|
|
::= { c3gGsmMinGprsQosEntry 1 }
|
|
|
|
c3gGsmMinGprsQosDelay OBJECT-TYPE
|
|
SYNTAX C3gGprsQosDelay
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum GPRS QoS delay classes."
|
|
::= { c3gGsmMinGprsQosEntry 2 }
|
|
|
|
c3gGsmMinGprsQosReliability OBJECT-TYPE
|
|
SYNTAX C3gGprsQosReliability
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum GPRS QoS reliability."
|
|
::= { c3gGsmMinGprsQosEntry 3 }
|
|
|
|
c3gGsmMinGprsQosPeakRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPeakRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum GPRS QoS peak rate."
|
|
::= { c3gGsmMinGprsQosEntry 4 }
|
|
|
|
c3gGsmMinGprsQosMeanRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosMeanRate
|
|
UNITS "octet-per-hour"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Minimum GPRS QoS mean rate."
|
|
::= { c3gGsmMinGprsQosEntry 5 }
|
|
|
|
c3gGsmMinGprsQosRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gGsmMinGprsQosEntry 6 }
|
|
|
|
|
|
|
|
c3gGsmNegoGprsQosTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmNegoGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS table. This table contains negotiated GPRS
|
|
QoS parameters returned in the Activate PDP Context Accept
|
|
message. The objects in this table are valid only if the value
|
|
of object c3gGsmPacketSessionStatus defined in
|
|
c3gGsmPacketSessionTable is 'active'. This table is applicable
|
|
only in 3G technology mode."
|
|
::= { c3gGsmPdpProfile 8 }
|
|
|
|
c3gGsmNegoGprsQosEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmNegoGprsQosEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmNegoGprsQosTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmPdpProfileIndex
|
|
}
|
|
::= { c3gGsmNegoGprsQosTable 1 }
|
|
|
|
C3gGsmNegoGprsQosEntry ::= SEQUENCE {
|
|
c3gGsmNegoGprsQosPrecedence C3gGprsQosPrecedence,
|
|
c3gGsmNegoGprsQosDelay C3gGprsQosDelay,
|
|
c3gGsmNegoGprsQosReliability C3gGprsQosReliability,
|
|
c3gGsmNegoGprsQosPeakRate C3gGprsQosPeakRate,
|
|
c3gGsmNegoGprsQosMeanRate C3gGprsQosMeanRate
|
|
}
|
|
|
|
c3gGsmNegoGprsQosPrecedence OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPrecedence
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS precedence."
|
|
::= { c3gGsmNegoGprsQosEntry 1 }
|
|
|
|
c3gGsmNegoGprsQosDelay OBJECT-TYPE
|
|
SYNTAX C3gGprsQosDelay
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS delay classes."
|
|
::= { c3gGsmNegoGprsQosEntry 2 }
|
|
|
|
c3gGsmNegoGprsQosReliability OBJECT-TYPE
|
|
SYNTAX C3gGprsQosReliability
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS reliability."
|
|
::= { c3gGsmNegoGprsQosEntry 3 }
|
|
|
|
c3gGsmNegoGprsQosPeakRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosPeakRate
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS peak rate."
|
|
::= { c3gGsmNegoGprsQosEntry 4 }
|
|
|
|
c3gGsmNegoGprsQosMeanRate OBJECT-TYPE
|
|
SYNTAX C3gGprsQosMeanRate
|
|
UNITS "octet-per-hour"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Negotiated GPRS QoS mean rate."
|
|
::= { c3gGsmNegoGprsQosEntry 5 }
|
|
|
|
|
|
c3gGsmRadio OBJECT IDENTIFIER
|
|
::= { c3gWanGsm 4 }
|
|
|
|
|
|
c3gGsmRadioTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G GSM/4G-LTE radio table."
|
|
::= { c3gGsmRadio 1 }
|
|
|
|
c3gGsmRadioEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmRadioEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmRadioTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gGsmRadioTable 1 }
|
|
|
|
C3gGsmRadioEntry ::= SEQUENCE {
|
|
c3gCurrentGsmRssi C3gRssi,
|
|
c3gCurrentGsmEcIo C3gEcIo,
|
|
c3gGsmCurrentBand INTEGER,
|
|
c3gGsmChannelNumber Unsigned32,
|
|
c3gGsmNumberOfNearbyCell Unsigned32
|
|
}
|
|
|
|
c3gCurrentGsmRssi OBJECT-TYPE
|
|
SYNTAX C3gRssi
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The GPRS/UMTS/LTE RSSI value."
|
|
::= { c3gGsmRadioEntry 1 }
|
|
|
|
c3gCurrentGsmEcIo OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The GPRS, UMTS or LTE Ec/Io value."
|
|
::= { c3gGsmRadioEntry 2 }
|
|
|
|
c3gGsmCurrentBand OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
invalid(2),
|
|
none(3),
|
|
gsm850(4),
|
|
gsm900(5),
|
|
gsm1800(6),
|
|
gsm1900(7),
|
|
wcdma800(8),
|
|
wcdma850(9),
|
|
wcdma1900(10),
|
|
wcdma2100(11),
|
|
lteBand(12)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPRS/UMTS/LTE band to which the modem is attached.
|
|
Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when
|
|
in LTE mode."
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmRadioEntry 3 }
|
|
|
|
c3gGsmChannelNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Channel number to which the modem is attached. This is only
|
|
applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
|
|
for the LTE uplink and downlink channel values"
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmRadioEntry 4 }
|
|
|
|
c3gGsmNumberOfNearbyCell OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the current total number of
|
|
nearby cell in the c3gGsmNearbyCellTable. User can
|
|
poll this object to get the total number of nearby
|
|
cell before polling c3gGsmNearbyCellTable."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmRadioEntry 5 }
|
|
|
|
|
|
|
|
c3gGsmNearbyCellTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmNearbyCellEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular GSM/4G-LTE nearby cell table. Object
|
|
c3gGsmNumberOfNearbyCell indicates the total
|
|
number of nearby cell in this table."
|
|
::= { c3gGsmRadio 2 }
|
|
|
|
c3gGsmNearbyCellEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmNearbyCellEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmNearbyCellTable."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gGsmNearbyCellIndex
|
|
}
|
|
::= { c3gGsmNearbyCellTable 1 }
|
|
|
|
C3gGsmNearbyCellEntry ::= SEQUENCE {
|
|
c3gGsmNearbyCellIndex Integer32,
|
|
c3gGsmNearbyCellPrimaryScramblingCode Unsigned32,
|
|
c3gGsmNearbyCellRscp Integer32,
|
|
c3gGsmNearbyCellEcIoMeasurement C3gEcIo
|
|
}
|
|
|
|
c3gGsmNearbyCellIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..100)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Nearby cell index, combined with entPhysicalIndex to access
|
|
the Nearby cell table c3gGsmNearbyCellTable."
|
|
::= { c3gGsmNearbyCellEntry 1 }
|
|
|
|
c3gGsmNearbyCellPrimaryScramblingCode OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Nearby cell primary scrambling code."
|
|
::= { c3gGsmNearbyCellEntry 2 }
|
|
|
|
c3gGsmNearbyCellRscp OBJECT-TYPE
|
|
SYNTAX Integer32 (-150..0)
|
|
UNITS "dB"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Nearby cell Received Signal Code Power (RSCP)."
|
|
::= { c3gGsmNearbyCellEntry 3 }
|
|
|
|
c3gGsmNearbyCellEcIoMeasurement OBJECT-TYPE
|
|
SYNTAX C3gEcIo
|
|
UNITS "dB"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Nearby cell Ec/Io measurement."
|
|
::= { c3gGsmNearbyCellEntry 4 }
|
|
|
|
|
|
|
|
c3gGsmHistoryTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmHistoryEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G GSM/4G-LTE RSSI history table. The history of RSSI
|
|
are carried in an octet of string. Each octet in the octet
|
|
string has a value from 0 to 150 and the 255 value is reserved
|
|
to indicate an uninitialized (Invalid) value. The format of
|
|
the octet string with n octets is as following:
|
|
[ octet 0 is latest,
|
|
octet 1 is latest-1,
|
|
.
|
|
.
|
|
octet n-2 is oldest-1,
|
|
octet n-1 is oldest ]
|
|
|
|
To convert the provided value into dBm the following formula
|
|
should be used:
|
|
dBm = (-1)*value;"
|
|
::= { c3gGsmRadio 3 }
|
|
|
|
c3gGsmHistoryEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmHistoryEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmHistoryTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gGsmHistoryTable 1 }
|
|
|
|
C3gGsmHistoryEntry ::= SEQUENCE {
|
|
c3gGsmHistoryRssiPerSecond OCTET STRING,
|
|
c3gGsmHistoryRssiPerMinute OCTET STRING,
|
|
c3gGsmHistoryRssiPerHour OCTET STRING
|
|
}
|
|
|
|
c3gGsmHistoryRssiPerSecond OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-second RSSI history. This object contains a
|
|
per-second history of RSSI values for the last 60 seconds."
|
|
::= { c3gGsmHistoryEntry 1 }
|
|
|
|
c3gGsmHistoryRssiPerMinute OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (60))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-minute weakest RSSI value history. This object
|
|
contains a per-minute history of weakest RSSI values for the
|
|
last 60 minutes. The octet in the string is the weakest RSSI
|
|
value measured in a minute interval."
|
|
::= { c3gGsmHistoryEntry 2 }
|
|
|
|
c3gGsmHistoryRssiPerHour OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (72))
|
|
UNITS "-dBm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Per-hour weakest RSSI value history. This object
|
|
contains a per-hour history of weakest RSSI values for the last
|
|
72 hours. The octet in the string is the weakest RSSI value
|
|
measured in an hour interval."
|
|
::= { c3gGsmHistoryEntry 3 }
|
|
|
|
|
|
c3gGsmSecurity OBJECT IDENTIFIER
|
|
::= { c3gWanGsm 5 }
|
|
|
|
|
|
c3gGsmSecurityTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gGsmSecurityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Cellular 3G GSM/4G-LTE security table."
|
|
::= { c3gGsmSecurity 1 }
|
|
|
|
c3gGsmSecurityEntry OBJECT-TYPE
|
|
SYNTAX C3gGsmSecurityEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry (conceptual row) in the c3gGsmSecurityTable."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gGsmSecurityTable 1 }
|
|
|
|
C3gGsmSecurityEntry ::= SEQUENCE {
|
|
c3gGsmChv1 INTEGER,
|
|
c3gGsmSimStatus INTEGER,
|
|
c3gGsmSimUserOperationRequired INTEGER,
|
|
c3gGsmNumberOfRetriesRemaining Unsigned32
|
|
}
|
|
|
|
c3gGsmChv1 OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
disabled(2),
|
|
enabled(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Card Holder Verification 1 (CHV1), if enabled, the PIN will be
|
|
verified, if disabled, the PIN will not be verified."
|
|
DEFVAL { disabled }
|
|
::= { c3gGsmSecurityEntry 1 }
|
|
|
|
c3gGsmSimStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
ok(2),
|
|
notInserted(3),
|
|
removed(4),
|
|
initFailure(5),
|
|
generalFailure(6),
|
|
locked(7),
|
|
chv1Blocked(8),
|
|
chv2Blocked(9),
|
|
chv1Rejected(10),
|
|
chv2Rejected(11),
|
|
mepLocked(12),
|
|
networkRejected(13)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"SIM status. Indicates whether the SIM is present or removed
|
|
from the SIM socket, and its current status."
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmSecurityEntry 2 }
|
|
|
|
c3gGsmSimUserOperationRequired OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
none(2),
|
|
enterChv1(3),
|
|
enterChv2(4),
|
|
enterUnblockChv1(5),
|
|
enterUnblockChv2(6),
|
|
enterMepCode(7)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If the SIM is protected (for example, because of CHV1 enabled),
|
|
it will indicate the type of user operation required."
|
|
DEFVAL { unknown }
|
|
::= { c3gGsmSecurityEntry 3 }
|
|
|
|
c3gGsmNumberOfRetriesRemaining OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the number of attempts remaining in case the SIM is
|
|
locked. If the number of retries becomes zero, the SIM is
|
|
blocked and becomes unusable."
|
|
DEFVAL { 0 }
|
|
::= { c3gGsmSecurityEntry 4 }
|
|
|
|
|
|
c3gWanLbsCommon OBJECT IDENTIFIER
|
|
::= { c3gWanLbs 1 }
|
|
|
|
|
|
c3gWanLbsCommonTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gWanLbsCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains information about the Cellular Location
|
|
Based service feature. This GPS data is provided by the wireless
|
|
modem upon GPS configuration."
|
|
::= { c3gWanLbsCommon 1 }
|
|
|
|
c3gWanLbsCommonEntry OBJECT-TYPE
|
|
SYNTAX C3gWanLbsCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This entry contains information about the
|
|
Cellular Location Based service
|
|
variables returned by the wireless modem."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gWanLbsCommonTable 1 }
|
|
|
|
C3gWanLbsCommonEntry ::= SEQUENCE {
|
|
c3gLbsModeSelected INTEGER,
|
|
c3gLbsState INTEGER,
|
|
c3gLbsLocFixError INTEGER,
|
|
c3gLbsLatitude SnmpAdminString,
|
|
c3gLbsLongitude SnmpAdminString,
|
|
c3gLbsTimeStamp SnmpAdminString,
|
|
c3gLbsLocUncertaintyAngle Unsigned32,
|
|
c3gLbsLocUncertaintyA Unsigned32,
|
|
c3gLbsLocUncertaintyPos Unsigned32,
|
|
c3gLbsFixtype INTEGER,
|
|
c3gLbsHeightValid TruthValue,
|
|
c3gLbsHeight Integer32,
|
|
c3gLbsLocUncertaintyVertical Unsigned32,
|
|
c3gLbsVelocityValid TruthValue,
|
|
c3gLbsHeading Unsigned32,
|
|
c3gLbsVelocityHorizontal Unsigned32,
|
|
c3gLbsVelocityVertical Unsigned32,
|
|
c3gLbsHepe Unsigned32,
|
|
c3gLbsNumSatellites Gauge32
|
|
}
|
|
|
|
c3gLbsModeSelected OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unKnown(1),
|
|
standAlone(2),
|
|
msBased(3),
|
|
msAssist(4),
|
|
reserved(5)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Mode of Location base service selected.
|
|
|
|
unKnown - mode selection unkown
|
|
standAlone - Standalone mode
|
|
msBased - MS-Based mode
|
|
msAssist - MS-Assist mode
|
|
reserved - reserved for future use"
|
|
DEFVAL { unKnown }
|
|
::= { c3gWanLbsCommonEntry 1 }
|
|
|
|
c3gLbsState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
gpsDisabled(1),
|
|
gpsAcquiring(2),
|
|
gpsEnabled(3),
|
|
gpsLocError(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location base service state.
|
|
|
|
gpsDisabled - GPS is disabled
|
|
gpsEnabled - GPS is enabled
|
|
gpsLocError - GPS encounters error
|
|
gpsAcquiring - GPS is acquiring fix"
|
|
DEFVAL { gpsDisabled }
|
|
::= { c3gWanLbsCommonEntry 2 }
|
|
|
|
c3gLbsLocFixError OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
offline(1),
|
|
noService(2),
|
|
noConnection(3),
|
|
noData(4),
|
|
sessionBusy(5),
|
|
reserved(6),
|
|
gpsDisabled(7),
|
|
connectionFailed(8),
|
|
errorState(9),
|
|
clientEnded(10),
|
|
uiEnded(11),
|
|
networkEnded(12),
|
|
timeout(13),
|
|
privacyLevel(14),
|
|
networkAccessError(15),
|
|
fixError(16),
|
|
pdeRejected(17),
|
|
trafficChannelExited(18),
|
|
e911(19),
|
|
serverError(20),
|
|
staleBSinformation(21),
|
|
resourceContention(22),
|
|
authenticationParameterFailed(23),
|
|
authenticationFailedLocal(24),
|
|
authenticationFailedNetwork(25),
|
|
vxLcsAgentAuthFail(26),
|
|
unknownSystemError(27),
|
|
unsupportedService(28),
|
|
subscriptionViolation(29),
|
|
desiredFixMethodFailed(30),
|
|
antennaSwitch(31),
|
|
noTxConfirmationReceived(32),
|
|
normalEndOfSession(33),
|
|
noErrorFromNetwork(34),
|
|
noResourcesLeftOnNetwork(35),
|
|
positionServerNotAvailable(36),
|
|
unsupportedProtocolVersion(37),
|
|
ssmolrErrorSystemFailure(38),
|
|
ssmolrErrorUnexpectedDataValue(39),
|
|
ssmolrErrorDataMissing(40),
|
|
ssmolrErrorFacilityNotSupported(41),
|
|
ssmolrErrorSsSubscriptionViolation(42),
|
|
ssmolrErrorPositionMethodFailure(43),
|
|
ssmolrErrorUndefined(44),
|
|
smlcTimeout(45),
|
|
mtGguardTimeExpired(46),
|
|
additionalAssistanceNeeded(47),
|
|
noFixError(48)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location base service fix error code."
|
|
REFERENCE
|
|
"Refer to the following documents for the error code's full
|
|
definitions. Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf
|
|
under Location Based Services section."
|
|
DEFVAL { noFixError }
|
|
::= { c3gWanLbsCommonEntry 3 }
|
|
|
|
c3gLbsLatitude OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location base service Latitude."
|
|
::= { c3gWanLbsCommonEntry 4 }
|
|
|
|
c3gLbsLongitude OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location base service longitude."
|
|
::= { c3gWanLbsCommonEntry 5 }
|
|
|
|
c3gLbsTimeStamp OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Location base service timestamp."
|
|
::= { c3gWanLbsCommonEntry 6 }
|
|
|
|
c3gLbsLocUncertaintyAngle OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "degrees"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPS Uncertainty parameter Angle, in degrees
|
|
for the Uncertainty info returned by the GPS
|
|
device while doing a location fix."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 7 }
|
|
|
|
c3gLbsLocUncertaintyA OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "meters"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPS Uncertainty parameter A, value in meters
|
|
for the Uncertainty info returned by the GPS
|
|
device while doing a location fix."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 8 }
|
|
|
|
c3gLbsLocUncertaintyPos OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "meters"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPS Uncertainty parameter position, value in meters
|
|
for the Uncertainty info returned by the GPS device
|
|
while doing a location fix."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 9 }
|
|
|
|
c3gLbsFixtype OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
twoDimension(2),
|
|
threeDimension(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The type of location fix in Location Base service.
|
|
|
|
none - default case, while LBS is not enabled.
|
|
twoDimension - 2D location fix.
|
|
threeDimension - 3D location fix."
|
|
DEFVAL { none }
|
|
::= { c3gWanLbsCommonEntry 10 }
|
|
|
|
c3gLbsHeightValid OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether the height returned by
|
|
the GPS device is valid during location fix."
|
|
DEFVAL { false }
|
|
::= { c3gWanLbsCommonEntry 11 }
|
|
|
|
c3gLbsHeight OBJECT-TYPE
|
|
SYNTAX Integer32 (-500..500)
|
|
UNITS "meters"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the GPS height parameter returned
|
|
by the GPS device while performing location fix."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 12 }
|
|
|
|
c3gLbsLocUncertaintyVertical OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "meters"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"GPS parameter vertical velocity parameter returned by
|
|
the GPS device while performing location fix."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 13 }
|
|
|
|
c3gLbsVelocityValid OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether the Velocity value
|
|
returned by the GPS device is valid."
|
|
DEFVAL { false }
|
|
::= { c3gWanLbsCommonEntry 14 }
|
|
|
|
c3gLbsHeading OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "degrees"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compass direction toward which the GPS receiver
|
|
is (or should be) moving."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 15 }
|
|
|
|
c3gLbsVelocityHorizontal OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "meters per second"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Horizontal Velocity in meters per second the GPS
|
|
device is heading. This is the value returned by
|
|
the GPS satellite relative to the last horizontal
|
|
location of the GPS device. If at Time X satellite
|
|
sees the location of GPS device is L1 and then at
|
|
Time Y satellite sees the location is L2 then
|
|
speed is (L2 - L1) / ( Y - X)."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 16 }
|
|
|
|
c3gLbsVelocityVertical OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "meters per second"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Vertical Velocity in meters per second
|
|
the GPS device is heading. This is the value returned by
|
|
the GPS satellite relative to the last vertical location of
|
|
the GPS device. If at Time X satellite sees the location
|
|
of GPS device is L1 and then at Time Y satellite sees
|
|
the location is L2 then speed is (L2 - L1) / ( Y - X)."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 17 }
|
|
|
|
c3gLbsHepe OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "centimeters"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Horizontal Estimated Position Error returned by the
|
|
GPS satellite for current position of the GPS device."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 18 }
|
|
|
|
c3gLbsNumSatellites OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of GPS satellites in vision to the modem
|
|
while GPS tracking is on."
|
|
DEFVAL { 0 }
|
|
::= { c3gWanLbsCommonEntry 19 }
|
|
|
|
|
|
c3gWanLbsSatelliteInfo OBJECT IDENTIFIER
|
|
::= { c3gWanLbs 2 }
|
|
|
|
|
|
c3gWanLbsSatelliteInfoTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gWanLbsSatelliteInfoEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides information on each satellite that is
|
|
visible to the modem during the location fix. These
|
|
satellites guide the device to acquire a 2D or 3D
|
|
location fix."
|
|
::= { c3gWanLbsSatelliteInfo 1 }
|
|
|
|
c3gWanLbsSatelliteInfoEntry OBJECT-TYPE
|
|
SYNTAX C3gWanLbsSatelliteInfoEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides information about each satellite's
|
|
elevation, azimuth, Signal to Noise ratio (SNR) and
|
|
its reference number local to the router."
|
|
INDEX {
|
|
entPhysicalIndex,
|
|
c3gWanLbsSatelliteInfoIndex
|
|
}
|
|
::= { c3gWanLbsSatelliteInfoTable 1 }
|
|
|
|
C3gWanLbsSatelliteInfoEntry ::= SEQUENCE {
|
|
c3gWanLbsSatelliteInfoIndex Integer32,
|
|
c3gWanLbsSatelliteNumber Integer32,
|
|
c3gWanLbsSatelliteElevation Integer32,
|
|
c3gWanLbsSatelliteAzimuth Integer32,
|
|
c3gWanLbsSatelliteInfoSignalNoiseRatio Integer32,
|
|
c3gWanLbsSatelliteUsed TruthValue,
|
|
c3gWanLbsSatelliteInfoRowStatus RowStatus
|
|
}
|
|
|
|
c3gWanLbsSatelliteInfoIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..1000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that is assigned to each satellite under a modem
|
|
and in combination with entPhysicalIndex uniquely identify it.
|
|
This index is assigned arbitrarily by the engine and is not
|
|
saved over reboots."
|
|
::= { c3gWanLbsSatelliteInfoEntry 1 }
|
|
|
|
c3gWanLbsSatelliteNumber OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each Satellite is assigned a unique number
|
|
within this device.This object can be used
|
|
to locate a particular satellite under
|
|
a modem."
|
|
REFERENCE
|
|
"Refer to the following documents for detailed
|
|
information of Satellites.
|
|
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
|
|
Location Based Services section"
|
|
::= { c3gWanLbsSatelliteInfoEntry 2 }
|
|
|
|
c3gWanLbsSatelliteElevation OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "degrees"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Angle of Elevation between the GPS antenna pointing direction,
|
|
directly towards the satellite, and the local horizontal plane.
|
|
It is the up-down angle"
|
|
REFERENCE
|
|
"Refer to the following documents for detailed
|
|
information of Satellites elevation.
|
|
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
|
|
Location Based Services section"
|
|
::= { c3gWanLbsSatelliteInfoEntry 3 }
|
|
|
|
c3gWanLbsSatelliteAzimuth OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "degrees"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Azimuth of the current satellite in context
|
|
referenced by the Satellite InfoIndex.
|
|
Azimuth is the degree of rotation of the
|
|
satellites dish on its vertical plane."
|
|
REFERENCE
|
|
"Refer to the following documents for detailed
|
|
information of Satellites Azimuth.
|
|
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
|
|
Location Based Services section"
|
|
::= { c3gWanLbsSatelliteInfoEntry 4 }
|
|
|
|
c3gWanLbsSatelliteInfoSignalNoiseRatio OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "db"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Signal to Noise Ratio(SNR) of received GPS signal.
|
|
SNR is refered to as the signal strength in
|
|
GPS standards."
|
|
REFERENCE
|
|
"Refer to the following documents for detailed
|
|
information of signal to noise ration in LBS.
|
|
Sierra Wireless CDMA EVDO CnS Reference_1.2.pdf under
|
|
Location Based Services section"
|
|
::= { c3gWanLbsSatelliteInfoEntry 5 }
|
|
|
|
c3gWanLbsSatelliteUsed OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Is this satellite in line of sight to the
|
|
modem used in calculating the GPS location?"
|
|
DEFVAL { false }
|
|
::= { c3gWanLbsSatelliteInfoEntry 6 }
|
|
|
|
c3gWanLbsSatelliteInfoRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The status of this conceptual row. This object is used to
|
|
manage creation, modification and deletion of rows in this
|
|
table."
|
|
::= { c3gWanLbsSatelliteInfoEntry 7 }
|
|
|
|
|
|
c3gWanSms OBJECT IDENTIFIER
|
|
::= { c3gWanSmsCommon 1 }
|
|
|
|
|
|
c3gSmsCommonTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF C3gSmsCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains Cellular SMS management
|
|
MIB objects."
|
|
::= { c3gWanSms 1 }
|
|
|
|
c3gSmsCommonEntry OBJECT-TYPE
|
|
SYNTAX C3gSmsCommonEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry contains counters for the SMS messages
|
|
received, placed, errored and archived on CDMA,
|
|
GSM or LTE based modems."
|
|
INDEX { entPhysicalIndex }
|
|
::= { c3gSmsCommonTable 1 }
|
|
|
|
C3gSmsCommonEntry ::= SEQUENCE {
|
|
c3gSmsServiceAvailable TruthValue,
|
|
c3gSmsOutSmsCount Counter32,
|
|
c3gSmsOutSmsErrorCount Counter32,
|
|
c3gSmsInSmsStorageUsed Gauge32,
|
|
c3gSmsInSmsStorageUnused Gauge32,
|
|
c3gSmsInSmsArchiveCount Gauge32,
|
|
c3gSmsInSmsArchiveErrorCount Gauge32,
|
|
c3gSmsArchiveUrl SnmpAdminString,
|
|
c3gSmsOutSmsStatus INTEGER,
|
|
c3gSmsInSmsCount Counter32,
|
|
c3gSmsInSmsDeleted Counter32,
|
|
c3gSmsInSmsStorageMax Counter64,
|
|
c3gSmsInSmsCallBack Counter32,
|
|
c3gSmsOutSmsPendingCount Gauge32,
|
|
c3gSmsOutSmsArchiveCount Gauge32,
|
|
c3gSmsOutSmsArchiveErrorCount Gauge32,
|
|
c3gSmsInSmsArchived Gauge32
|
|
}
|
|
|
|
c3gSmsServiceAvailable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the availability of SMS Service."
|
|
DEFVAL { false }
|
|
::= { c3gSmsCommonEntry 1 }
|
|
|
|
c3gSmsOutSmsCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS messages which have been sent
|
|
successfully."
|
|
::= { c3gSmsCommonEntry 2 }
|
|
|
|
c3gSmsOutSmsErrorCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS message that could not be sent."
|
|
::= { c3gSmsCommonEntry 3 }
|
|
|
|
c3gSmsInSmsStorageUsed OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS message records space used in the
|
|
Incoming SMS message storage. One standard
|
|
SMS message (cdma or gsm) occupies 1 unit of
|
|
record storage space. A big SMS message can span
|
|
'n' sms record space but still be called as 1 SMS
|
|
message. Storage used can be greater than or equal
|
|
to total number of Incoming SMS received."
|
|
::= { c3gSmsCommonEntry 4 }
|
|
|
|
c3gSmsInSmsStorageUnused OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of SMS messages record space left
|
|
unused in the Incoming SMS message storage.
|
|
This is equal to c3gSmsInSmsStorageMax -
|
|
c3gSmsInSmsStorageUsed."
|
|
::= { c3gSmsCommonEntry 5 }
|
|
|
|
c3gSmsInSmsArchiveCount OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of successful archive of Incoming SMS messages
|
|
since router reload. Each SMS message occupies x bytes of
|
|
space. So if the incoming message is huge, then it is
|
|
archived as multiple of x bytes but still called as one
|
|
SMS message. This is the difference between
|
|
c3gSmsInSmsArchiveCount and c3gSmsInSmsArchived."
|
|
::= { c3gSmsCommonEntry 6 }
|
|
|
|
c3gSmsInSmsArchiveErrorCount OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of Incoming SMS messages that could not be
|
|
archived since device was reloaded."
|
|
::= { c3gSmsCommonEntry 7 }
|
|
|
|
c3gSmsArchiveUrl OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"URL of the sms archive directory on the ftp server.
|
|
The url will be of this format
|
|
ftp://x.y.z.k/user/dirname"
|
|
::= { c3gSmsCommonEntry 8 }
|
|
|
|
c3gSmsOutSmsStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
success(2),
|
|
copySmsHeader(3),
|
|
copySmsBody(4),
|
|
sent(5),
|
|
receivedSentNotification(6),
|
|
receivedOutMsgNumber(7),
|
|
receivedOutMsgStatus(8)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Status of the last send operation of outgoing
|
|
SMS message to the network."
|
|
::= { c3gSmsCommonEntry 9 }
|
|
|
|
c3gSmsInSmsCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS messages which have been
|
|
received successfully and stored in router.
|
|
These SMS's are a mirror copy of SMS stored in
|
|
Modem or SIM"
|
|
::= { c3gSmsCommonEntry 10 }
|
|
|
|
c3gSmsInSmsDeleted OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS messages which have been
|
|
deleted since router boot up. This does
|
|
not include SMS messages that are already
|
|
archived."
|
|
::= { c3gSmsCommonEntry 11 }
|
|
|
|
c3gSmsInSmsStorageMax OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of SMS message records space allocated
|
|
in the router's DRAM to store Incoming SMS messages."
|
|
::= { c3gSmsCommonEntry 12 }
|
|
|
|
c3gSmsInSmsCallBack OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of incoming SMS messages that triggered
|
|
callback."
|
|
::= { c3gSmsCommonEntry 13 }
|
|
|
|
c3gSmsOutSmsPendingCount OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of outgoing SMS messages that are in
|
|
pending queue of the router."
|
|
::= { c3gSmsCommonEntry 14 }
|
|
|
|
c3gSmsOutSmsArchiveCount OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of successfull archive of outgoing SMS messages
|
|
since router reload."
|
|
::= { c3gSmsCommonEntry 15 }
|
|
|
|
c3gSmsOutSmsArchiveErrorCount OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of failed archive of outgoing SMS messages
|
|
since router reload."
|
|
::= { c3gSmsCommonEntry 16 }
|
|
|
|
c3gSmsInSmsArchived OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "msgs"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of Incoming SMS messages that are successfully
|
|
archived since router reload."
|
|
::= { c3gSmsCommonEntry 17 }
|
|
|
|
|
|
|
|
-- Default Notification Type
|
|
|
|
c3gModemUpNotif NOTIFICATION-TYPE
|
|
OBJECTS { entPhysicalName }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the notification that the modem has been detected by
|
|
host interface. Users can enable or disable the generation of
|
|
this notification by using object c3gModemUpNotifEnabled."
|
|
::= { ciscoWan3gMIBNotifs 1 }
|
|
|
|
c3gModemDownNotif NOTIFICATION-TYPE
|
|
OBJECTS { entPhysicalName }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the notification that the modem has not been detected
|
|
by host interface, or has been disconnected from host interface.
|
|
Users can enable or disable the generation of this notification
|
|
by using object c3gModemDownNotifEnabled."
|
|
::= { ciscoWan3gMIBNotifs 2 }
|
|
|
|
c3gServiceChangedNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gPreviousServiceType,
|
|
c3gCurrentServiceType
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Notification for service change event. Objects
|
|
c3gPreviousServiceType and c3gCurrentServiceType will be
|
|
included in the notification. Users can enable or disable the
|
|
generation of this notification by using object
|
|
c3gServiceChangedNotifEnabled."
|
|
::= { ciscoWan3gMIBNotifs 3 }
|
|
|
|
c3gNetworkChangedNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gCurrentSid,
|
|
c3gCurrentNid,
|
|
c3gGsmMcc,
|
|
c3gGsmMnc,
|
|
c3gRoamingStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Notification for network change event. Objects c3gCurrentSid,
|
|
c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will
|
|
be included in the notification. Users can enable or disable
|
|
the generation of this notification by using object
|
|
c3gNetworkChangedNotifEnabled."
|
|
::= { ciscoWan3gMIBNotifs 4 }
|
|
|
|
c3gConnectionStatusChangedNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gConnectionStatus,
|
|
c3gCurrentServiceType
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Notification for connection status change event. Objects
|
|
c3gConnectionStatus and c3gCurrentServiceType will be included
|
|
in the notification. Users can use object
|
|
c3gConnectionStatusChangedNotifFlag to control what connection
|
|
status changes will cause the generation of this notification."
|
|
::= { ciscoWan3gMIBNotifs 5 }
|
|
|
|
c3gRssiOnsetNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gNotifRadioService,
|
|
c3gNotifRssi
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If RSSI goes below c3gRssiOnsetNotifThreshold and the service
|
|
bit in c3gRssiOnsetNotifFlag is set, this notification will be
|
|
generated. Object c3gNotifRadioService will indicate which
|
|
service generates this notification and the associated RSSI
|
|
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
|
|
is used to indicate the RSSI value that triggers the
|
|
notification, user should go to the corresponding radio table to
|
|
get the current RSSI value."
|
|
::= { ciscoWan3gMIBNotifs 6 }
|
|
|
|
c3gRssiAbateNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gNotifRadioService,
|
|
c3gNotifRssi
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If RSSI goes above c3gRssiAbateNotifThreshold and the service
|
|
bit in c3gRssiAbateNotifFlag is set, this notification will be
|
|
generated. Object c3gNotifRadioService will indicate which
|
|
service generates this notification and the associated RSSI
|
|
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
|
|
is used to indicate the RSSI value that triggers the
|
|
notification, user should go to the corresponding radio table to
|
|
get the current RSSI value."
|
|
::= { ciscoWan3gMIBNotifs 7 }
|
|
|
|
c3gEcIoOnsetNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gNotifRadioService,
|
|
c3gNotifEcIo
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service
|
|
bit in c3gEcIoOnsetNotifFlag is set, this notification will be
|
|
generated. Object c3gNotifRadioService will indicate which
|
|
service generates this notification and the associated Ec/Io
|
|
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
|
|
is used to indicate the Ec/Io value that triggers the
|
|
notification, user should go to the corresponding radio table to
|
|
get the current Ec/Io value."
|
|
::= { ciscoWan3gMIBNotifs 8 }
|
|
|
|
c3gEcIoAbateNotif NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
c3gNotifRadioService,
|
|
c3gNotifEcIo
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If Ec/Io goes above c3gEcIoAbateNotifThreshold and the service
|
|
bit in c3gEcIoAbateNotifFlag is set, this notification will be
|
|
generated. Object c3gNotifRadioService will indicate which
|
|
service generates this notification and the associated Ec/Io
|
|
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
|
|
is used to indicate the Ec/Io value that triggers the
|
|
notification, user should go to the corresponding radio table to
|
|
get the current Ec/Io value."
|
|
::= { ciscoWan3gMIBNotifs 9 }
|
|
|
|
c3gModemTemperOnsetNotif NOTIFICATION-TYPE
|
|
OBJECTS { c3gModemTemperature }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If modem temperature goes above
|
|
c3gModemTemperOnsetNotifThreshold and the value of
|
|
c3gModemTemperOnsetNotifEnabled is 'true', this notification
|
|
will be generated and the current value of c3gModemTemperature
|
|
will be included in this notification."
|
|
::= { ciscoWan3gMIBNotifs 10 }
|
|
|
|
c3gModemTemperAbateNotif NOTIFICATION-TYPE
|
|
OBJECTS { c3gModemTemperature }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If modem temperature goes below
|
|
c3gModemTemperAbateNotifThreshold and the value of
|
|
c3gModemTemperAbateNotifEnabled is 'true', this notification
|
|
will be generated and the current value of c3gModemTemperature
|
|
will be included in this notification."
|
|
::= { ciscoWan3gMIBNotifs 11 }
|
|
|
|
c3gModemTemperOnsetRecoveryNotif NOTIFICATION-TYPE
|
|
OBJECTS { c3gModemTemperature }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This trap is generated as a recovery notification for
|
|
c3gModemTemperOnsetNotif.This trap is generated when the current
|
|
value of c3gModemTemperature goes below
|
|
c3gModemTemperOnsetNotifThreshold once it has generated the
|
|
c3gModemTemperOnsetNotif and the value of
|
|
c3gModemTemperOnsetNotifEnabled is 'true'.
|
|
|
|
c3gModemTemperature contains the current value of modem
|
|
temperature."
|
|
::= { ciscoWan3gMIBNotifs 12 }
|
|
|
|
c3gModemTemperAbateRecoveryNotif NOTIFICATION-TYPE
|
|
OBJECTS { c3gModemTemperature }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This trap is generated as a recovery notification for
|
|
c3gModemTemperAbateNotif.This trap is generated when the current
|
|
value of c3gModemTemperature goes above
|
|
c3gModemTemperAbateNotifThreshold once it has generated the
|
|
c3gModemTemperAbateNotif and the value of
|
|
c3gModemTemperAbateNotifEnabled is 'true'
|
|
|
|
c3gModemTemperature contains the current value of modem
|
|
temperature"
|
|
::= { ciscoWan3gMIBNotifs 13 }
|
|
-- Conformance
|
|
|
|
ciscoWan3gMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBConform 1 }
|
|
|
|
ciscoWan3gMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoWan3gMIBConform 2 }
|
|
|
|
|
|
ciscoWan3gMIBCompliance MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This is a default module-compliance
|
|
containing default object groups."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoWan3gMIBNotificationGroup,
|
|
ciscoWan3gMIBCommonObjectGroup
|
|
}
|
|
|
|
GROUP ciscoWan3gMIBCdmaObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for CDMA standard."
|
|
|
|
GROUP ciscoWan3gMIBGsmObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for GSM/LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBSmsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included
|
|
for SMS service on CDMA, GSM and LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBLbsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for
|
|
Location based service on CDMA, GSM and LTE standard."
|
|
::= { ciscoWan3gMIBCompliances 1 }
|
|
|
|
ciscoWan3gMIBCompliance1 MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for the CISCO-WAN-3G-MIB."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoWan3gMIBNotificationGroup,
|
|
ciscoWan3gMIBCommonObjectGroup
|
|
}
|
|
|
|
GROUP ciscoWan3gMIBCdmaObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for CDMA standard."
|
|
|
|
GROUP ciscoWan3gMIBGsmObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for GSM and
|
|
LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBSmsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included
|
|
for SMS service on CDMA, GSM and LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBLbsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for
|
|
Location based service on CDMA, GSM and LTE standard."
|
|
::= { ciscoWan3gMIBCompliances 2 }
|
|
|
|
ciscoWan3gMIBComplianceRev1 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is a default module-compliance
|
|
containing default object groups."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoWan3gMIBNotificationGroupRev1,
|
|
ciscoWan3gMIBCommonObjectGroup
|
|
}
|
|
|
|
GROUP ciscoWan3gMIBCdmaObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for CDMA standard."
|
|
|
|
GROUP ciscoWan3gMIBGsmObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for GSM/LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBSmsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included
|
|
for SMS service on CDMA, GSM and LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBLbsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for
|
|
Location based service on CDMA, GSM and LTE standard."
|
|
::= { ciscoWan3gMIBCompliances 3 }
|
|
|
|
ciscoWan3gMIBCompliance1Rev1 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for the CISCO-WAN-3G-MIB."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoWan3gMIBNotificationGroupRev1,
|
|
ciscoWan3gMIBCommonObjectGroup
|
|
}
|
|
|
|
GROUP ciscoWan3gMIBCdmaObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for CDMA standard."
|
|
|
|
GROUP ciscoWan3gMIBGsmObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for GSM and
|
|
LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBSmsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included
|
|
for SMS service on CDMA, GSM and LTE standard."
|
|
|
|
GROUP ciscoWan3gMIBLbsObjectGroup
|
|
DESCRIPTION
|
|
"This object group should be included for
|
|
Location based service on CDMA, GSM and LTE standard."
|
|
::= { ciscoWan3gMIBCompliances 4 }
|
|
|
|
-- Units of Conformance
|
|
|
|
ciscoWan3gMIBCommonObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
c3gStandard,
|
|
c3gCapability,
|
|
c3gModemState,
|
|
c3gPreviousServiceType,
|
|
c3gCurrentServiceType,
|
|
c3gRoamingStatus,
|
|
c3gCurrentSystemTime,
|
|
c3gConnectionStatus,
|
|
c3gNotifRadioService,
|
|
c3gNotifRssi,
|
|
c3gNotifEcIo,
|
|
c3gModemTemperature,
|
|
c3gRssiOnsetNotifThreshold,
|
|
c3gRssiAbateNotifThreshold,
|
|
c3gEcIoOnsetNotifThreshold,
|
|
c3gEcIoAbateNotifThreshold,
|
|
c3gModemTemperOnsetNotifThreshold,
|
|
c3gModemTemperAbateNotifThreshold,
|
|
c3gModemReset,
|
|
c3gModemUpNotifEnabled,
|
|
c3gModemDownNotifEnabled,
|
|
c3gServiceChangedNotifEnabled,
|
|
c3gNetworkChangedNotifEnabled,
|
|
c3gConnectionStatusChangedNotifFlag,
|
|
c3gRssiOnsetNotifFlag,
|
|
c3gRssiAbateNotifFlag,
|
|
c3gEcIoOnsetNotifFlag,
|
|
c3gEcIoAbateNotifFlag,
|
|
c3gModemTemperOnsetNotifEnabled,
|
|
c3gModemTemperAbateNotifEnabled,
|
|
c3gGpsState
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of common objects for Cellular interface."
|
|
::= { ciscoWan3gMIBGroups 1 }
|
|
|
|
ciscoWan3gMIBCdmaObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
c3gCdmaTotalCallDuration,
|
|
c3gCdmaTotalTransmitted,
|
|
c3gCdmaTotalReceived,
|
|
c3gHdrDdtmPreference,
|
|
c3gOutgoingCallNumber,
|
|
c3gHdrAtState,
|
|
c3gHdrSessionState,
|
|
c3gUati,
|
|
c3gColorCode,
|
|
c3gRati,
|
|
c3gHdrSessionDuration,
|
|
c3gHdrSessionStart,
|
|
c3gHdrSessionEnd,
|
|
c3gAuthStatus,
|
|
c3gHdrDrc,
|
|
c3gHdrDrcCover,
|
|
c3gHdrRri,
|
|
c3gCdmaCurrentTransmitted,
|
|
c3gCdmaCurrentReceived,
|
|
c3gCdmaCurrentCallStatus,
|
|
c3gCdmaCurrentCallDuration,
|
|
c3gCdmaCurrentCallType,
|
|
c3gCdmaLastCallDisconnReason,
|
|
c3gCdmaLastConnError,
|
|
c3gMobileIpErrorCode,
|
|
c3gEsn,
|
|
c3gModemActivationStatus,
|
|
c3gAccountActivationDate,
|
|
c3gCdmaRoamingPreference,
|
|
c3gPrlVersion,
|
|
c3gMdn,
|
|
c3gMsid,
|
|
c3gMsl,
|
|
c3gCdmaCurrentServiceStatus,
|
|
c3gCdmaHybridModePreference,
|
|
c3gCdmaCurrentRoamingStatus,
|
|
c3gCurrentIdleDigitalMode,
|
|
c3gCurrentSid,
|
|
c3gCurrentNid,
|
|
c3gCurrentCallSetupMode,
|
|
c3gSipUsername,
|
|
c3gSipPassword,
|
|
c3gServingBaseStationLongitude,
|
|
c3gServingBaseStationLatitude,
|
|
c3gNumberOfDataProfileConfigurable,
|
|
c3gCurrentActiveDataProfile,
|
|
c3gNai,
|
|
c3gAaaPassword,
|
|
c3gMnHaSs,
|
|
c3gMnHaSpi,
|
|
c3gMnAaaSs,
|
|
c3gMnAaaSpi,
|
|
c3gReverseTunnelPreference,
|
|
c3gHomeAddrType,
|
|
c3gHomeAddr,
|
|
c3gPriHaAddrType,
|
|
c3gPriHaAddr,
|
|
c3gSecHaAddrType,
|
|
c3gSecHaAddr,
|
|
c3gCurrent1xRttRssi,
|
|
c3gCurrent1xRttEcIo,
|
|
c3gCurrent1xRttChannelNumber,
|
|
c3gCurrent1xRttChannelState,
|
|
c3gCurrentEvDoRssi,
|
|
c3gCurrentEvDoEcIo,
|
|
c3gCurrentEvDoChannelNumber,
|
|
c3gSectorId,
|
|
c3gSubnetMask,
|
|
c3gHdrColorCode,
|
|
c3gPnOffset,
|
|
c3gRxMainGainControl,
|
|
c3gRxDiversityGainControl,
|
|
c3gTxTotalPower,
|
|
c3gTxGainAdjust,
|
|
c3gCarrierToInterferenceRatio,
|
|
c3g1xRttBandClass,
|
|
c3gEvDoBandClass,
|
|
c3gCdmaHistory1xRttRssiPerSecond,
|
|
c3gCdmaHistory1xRttRssiPerMinute,
|
|
c3gCdmaHistory1xRttRssiPerHour,
|
|
c3gCdmaHistoryEvDoRssiPerSecond,
|
|
c3gCdmaHistoryEvDoRssiPerMinute,
|
|
c3gCdmaHistoryEvDoRssiPerHour,
|
|
c3gCdmaPinSecurityStatus,
|
|
c3gCdmaPowerUpLockStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects for Cellular 3G CDMA."
|
|
::= { ciscoWan3gMIBGroups 2 }
|
|
|
|
ciscoWan3gMIBGsmObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
c3gGsmTotalByteTransmitted,
|
|
c3gGsmTotalByteReceived,
|
|
c3gGsmPacketSessionStatus,
|
|
c3gGsmPdpType,
|
|
c3gGsmPdpAddress,
|
|
c3gGsmNegoUmtsQosTrafficClass,
|
|
c3gGsmNegoUmtsQosMaxUpLinkBitRate,
|
|
c3gGsmNegoUmtsQosMaxDownLinkBitRate,
|
|
c3gGsmNegoUmtsQosGuaUpLinkBitRate,
|
|
c3gGsmNegoUmtsQosGuaDownLinkBitRate,
|
|
c3gGsmNegoUmtsQosOrder,
|
|
c3gGsmNegoUmtsQosErroneousSdu,
|
|
c3gGsmNegoUmtsQosMaxSduSize,
|
|
c3gGsmNegoUmtsQosSer,
|
|
c3gGsmNegoUmtsQosBer,
|
|
c3gGsmNegoUmtsQosDelay,
|
|
c3gGsmNegoUmtsQosPriority,
|
|
c3gGsmNegoUmtsQosSrcStatDescriptor,
|
|
c3gGsmNegoUmtsQosSignalIndication,
|
|
c3gGsmNegoGprsQosPrecedence,
|
|
c3gGsmNegoGprsQosDelay,
|
|
c3gGsmNegoGprsQosReliability,
|
|
c3gGsmNegoGprsQosPeakRate,
|
|
c3gGsmNegoGprsQosMeanRate,
|
|
c3gImsi,
|
|
c3gImei,
|
|
c3gIccId,
|
|
c3gMsisdn,
|
|
c3gFsn,
|
|
c3gModemStatus,
|
|
c3gGsmRoamingPreference,
|
|
c3gGsmLac,
|
|
c3gGsmCurrentServiceStatus,
|
|
c3gGsmCurrentServiceError,
|
|
c3gGsmCurrentService,
|
|
c3gGsmPacketService,
|
|
c3gGsmCurrentRoamingStatus,
|
|
c3gGsmNetworkSelectionMode,
|
|
c3gGsmCountry,
|
|
c3gGsmNetwork,
|
|
c3gGsmMcc,
|
|
c3gGsmMnc,
|
|
c3gGsmRac,
|
|
c3gGsmCurrentCellId,
|
|
c3gGsmCurrentPrimaryScramblingCode,
|
|
c3gGsmPlmnSelection,
|
|
c3gGsmRegPlmn,
|
|
c3gGsmPlmnAbbr,
|
|
c3gGsmServiceProvider,
|
|
c3gGsmPdpProfileType,
|
|
c3gGsmPdpProfileAddr,
|
|
c3gGsmPdpProfileApn,
|
|
c3gGsmPdpProfileAuthenType,
|
|
c3gGsmPdpProfileUsername,
|
|
c3gGsmPdpProfilePassword,
|
|
c3gGsmPdpProfileRowStatus,
|
|
c3gGsmReqUmtsQosTrafficClass,
|
|
c3gGsmReqUmtsQosMaxUpLinkBitRate,
|
|
c3gGsmReqUmtsQosMaxDownLinkBitRate,
|
|
c3gGsmReqUmtsQosGuaUpLinkBitRate,
|
|
c3gGsmReqUmtsQosGuaDownLinkBitRate,
|
|
c3gGsmReqUmtsQosOrder,
|
|
c3gGsmReqUmtsQosErroneousSdu,
|
|
c3gGsmReqUmtsQosMaxSduSize,
|
|
c3gGsmReqUmtsQosSer,
|
|
c3gGsmReqUmtsQosBer,
|
|
c3gGsmReqUmtsQosDelay,
|
|
c3gGsmReqUmtsQosPriority,
|
|
c3gGsmReqUmtsQosSrcStatDescriptor,
|
|
c3gGsmReqUmtsQosSignalIndication,
|
|
c3gGsmReqUmtsQosRowStatus,
|
|
c3gGsmMinUmtsQosTrafficClass,
|
|
c3gGsmMinUmtsQosMaxUpLinkBitRate,
|
|
c3gGsmMinUmtsQosMaxDownLinkBitRate,
|
|
c3gGsmMinUmtsQosGuaUpLinkBitRate,
|
|
c3gGsmMinUmtsQosGuaDownLinkBitRate,
|
|
c3gGsmMinUmtsQosOrder,
|
|
c3gGsmMinUmtsQosErroneousSdu,
|
|
c3gGsmMinUmtsQosMaxSduSize,
|
|
c3gGsmMinUmtsQosSer,
|
|
c3gGsmMinUmtsQosBer,
|
|
c3gGsmMinUmtsQosDelay,
|
|
c3gGsmMinUmtsQosPriority,
|
|
c3gGsmMinUmtsQosSrcStatDescriptor,
|
|
c3gGsmMinUmtsQosSignalIndication,
|
|
c3gGsmMinUmtsQosRowStatus,
|
|
c3gGsmReqGprsQosPrecedence,
|
|
c3gGsmReqGprsQosDelay,
|
|
c3gGsmReqGprsQosReliability,
|
|
c3gGsmReqGprsQosPeakRate,
|
|
c3gGsmReqGprsQosMeanRate,
|
|
c3gGsmReqGprsQosRowStatus,
|
|
c3gGsmMinGprsQosPrecedence,
|
|
c3gGsmMinGprsQosDelay,
|
|
c3gGsmMinGprsQosReliability,
|
|
c3gGsmMinGprsQosPeakRate,
|
|
c3gGsmMinGprsQosMeanRate,
|
|
c3gGsmMinGprsQosRowStatus,
|
|
c3gCurrentGsmRssi,
|
|
c3gCurrentGsmEcIo,
|
|
c3gGsmCurrentBand,
|
|
c3gGsmChannelNumber,
|
|
c3gGsmNumberOfNearbyCell,
|
|
c3gGsmNearbyCellPrimaryScramblingCode,
|
|
c3gGsmNearbyCellRscp,
|
|
c3gGsmNearbyCellEcIoMeasurement,
|
|
c3gGsmHistoryRssiPerSecond,
|
|
c3gGsmHistoryRssiPerMinute,
|
|
c3gGsmHistoryRssiPerHour,
|
|
c3gGsmChv1,
|
|
c3gGsmSimStatus,
|
|
c3gGsmSimUserOperationRequired,
|
|
c3gGsmNumberOfRetriesRemaining
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects for Cellular 3G GSM and LTE."
|
|
::= { ciscoWan3gMIBGroups 3 }
|
|
|
|
ciscoWan3gMIBNotificationGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
c3gModemUpNotif,
|
|
c3gModemDownNotif,
|
|
c3gServiceChangedNotif,
|
|
c3gNetworkChangedNotif,
|
|
c3gConnectionStatusChangedNotif,
|
|
c3gRssiOnsetNotif,
|
|
c3gEcIoOnsetNotif,
|
|
c3gRssiAbateNotif,
|
|
c3gEcIoAbateNotif,
|
|
c3gModemTemperOnsetNotif,
|
|
c3gModemTemperAbateNotif
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects for Cellular WAN notifications.
|
|
ciscoWan3gMIBNotificationGroup object is superseded by
|
|
ciscoWan3gMIBNotificationGroupRev1."
|
|
::= { ciscoWan3gMIBGroups 4 }
|
|
|
|
ciscoWan3gMIBLbsObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
c3gLbsModeSelected,
|
|
c3gLbsState,
|
|
c3gLbsLocFixError,
|
|
c3gLbsLatitude,
|
|
c3gLbsLongitude,
|
|
c3gLbsTimeStamp,
|
|
c3gLbsLocUncertaintyAngle,
|
|
c3gLbsLocUncertaintyA,
|
|
c3gLbsLocUncertaintyPos,
|
|
c3gLbsFixtype,
|
|
c3gLbsHeightValid,
|
|
c3gLbsHeight,
|
|
c3gLbsLocUncertaintyVertical,
|
|
c3gLbsVelocityValid,
|
|
c3gLbsHeading,
|
|
c3gLbsVelocityHorizontal,
|
|
c3gLbsVelocityVertical,
|
|
c3gLbsHepe,
|
|
c3gLbsNumSatellites,
|
|
c3gWanLbsSatelliteNumber,
|
|
c3gWanLbsSatelliteElevation,
|
|
c3gWanLbsSatelliteAzimuth,
|
|
c3gWanLbsSatelliteUsed,
|
|
c3gWanLbsSatelliteInfoSignalNoiseRatio,
|
|
c3gWanLbsSatelliteInfoRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of common objects for
|
|
Cellular Location Based Service."
|
|
::= { ciscoWan3gMIBGroups 5 }
|
|
|
|
ciscoWan3gMIBSmsObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
c3gSmsServiceAvailable,
|
|
c3gSmsOutSmsCount,
|
|
c3gSmsOutSmsErrorCount,
|
|
c3gSmsInSmsStorageUsed,
|
|
c3gSmsInSmsStorageUnused,
|
|
c3gSmsInSmsArchiveCount,
|
|
c3gSmsInSmsArchiveErrorCount,
|
|
c3gSmsInSmsArchived,
|
|
c3gSmsArchiveUrl,
|
|
c3gSmsOutSmsStatus,
|
|
c3gSmsInSmsCount,
|
|
c3gSmsInSmsDeleted,
|
|
c3gSmsInSmsStorageMax,
|
|
c3gSmsInSmsCallBack,
|
|
c3gSmsOutSmsPendingCount,
|
|
c3gSmsOutSmsArchiveCount,
|
|
c3gSmsOutSmsArchiveErrorCount
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of common objects for
|
|
Cellular Short Messaging Service."
|
|
::= { ciscoWan3gMIBGroups 6 }
|
|
|
|
ciscoWan3gMIBNotificationGroupRev1 NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
c3gModemUpNotif,
|
|
c3gModemDownNotif,
|
|
c3gServiceChangedNotif,
|
|
c3gNetworkChangedNotif,
|
|
c3gConnectionStatusChangedNotif,
|
|
c3gRssiOnsetNotif,
|
|
c3gEcIoOnsetNotif,
|
|
c3gRssiAbateNotif,
|
|
c3gEcIoAbateNotif,
|
|
c3gModemTemperOnsetNotif,
|
|
c3gModemTemperAbateNotif,
|
|
c3gModemTemperOnsetRecoveryNotif,
|
|
c3gModemTemperAbateRecoveryNotif
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects for Cellular WAN notifications."
|
|
::= { ciscoWan3gMIBGroups 7 }
|
|
|
|
END
|
|
|
|
|
|
|
|
|
|
|
|
|