858 lines
31 KiB
Plaintext
858 lines
31 KiB
Plaintext
BFD-STD-MIB DEFINITIONS ::= BEGIN
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE,
|
|
Unsigned32, Counter32, Counter64,
|
|
NOTIFICATION-TYPE
|
|
FROM SNMPv2-SMI -- [RFC2578]
|
|
|
|
MODULE-COMPLIANCE, OBJECT-GROUP,
|
|
NOTIFICATION-GROUP
|
|
FROM SNMPv2-CONF -- [RFC2580]
|
|
|
|
TEXTUAL-CONVENTION, TruthValue,
|
|
RowStatus, StorageType, TimeStamp
|
|
FROM SNMPv2-TC -- [RFC2579]
|
|
|
|
InetAddress, InetAddressType, InetPortNumber
|
|
FROM INET-ADDRESS-MIB -- [RFC3291]
|
|
|
|
-- Juniper specific *** JNX ***
|
|
jnxBfdExperiment -- *** JNX ***
|
|
FROM JUNIPER-EXPERIMENT-MIB -- *** JNX ***
|
|
;
|
|
|
|
bfdMIB MODULE-IDENTITY
|
|
LAST-UPDATED "200507221200Z" -- 04 July 2005 12:00:00 EST
|
|
ORGANIZATION "IETF"
|
|
CONTACT-INFO
|
|
" Thomas D. Nadeau
|
|
Cisco Systems, Inc.
|
|
Email: tnadeau@cisco.com
|
|
|
|
Zafar Ali
|
|
Cisco Systems, Inc.
|
|
Email: zali@cisco.com
|
|
"
|
|
DESCRIPTION
|
|
"Bidirectional Forwarding Management Information Base."
|
|
|
|
-- Revision history.
|
|
REVISION
|
|
"200508221200Z" -- 04 August 2005 12:00:00 EST
|
|
DESCRIPTION
|
|
"Initial version. Published as RFC xxxx." -- RFC-editor pls fill
|
|
-- in xxxx
|
|
::= { jnxBfdExperiment 1 }
|
|
|
|
-- Top level components of this MIB module.
|
|
|
|
bfdNotifications OBJECT IDENTIFIER ::= { bfdMIB 0 }
|
|
|
|
bfdObjects OBJECT IDENTIFIER ::= { bfdMIB 1 }
|
|
|
|
bfdConformance OBJECT IDENTIFIER ::= { bfdMIB 3 }
|
|
|
|
bfdScalarObjects OBJECT IDENTIFIER ::= { bfdObjects 1 }
|
|
|
|
|
|
-- Textual Conventions
|
|
|
|
BfdSessIndexTC ::= TEXTUAL-CONVENTION
|
|
DISPLAY-HINT "d"
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index used to uniquely identify BFD sessions."
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
|
|
BfdInterval ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD interval delay in microseconds."
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
|
|
BfdDiag ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A common BFD diagnostic code."
|
|
|
|
SYNTAX INTEGER { noDiagnostic(1),
|
|
controlDetectionTimeExpired(2),
|
|
echoFunctionFailed(3),
|
|
neighborSignaledSessionDown(4),
|
|
forwardingPlaneReset(5),
|
|
pathDown(6),
|
|
concatenatedPathDown(7),
|
|
administrativelyDown(8),
|
|
reverseConcatenatedPathDown (9)
|
|
}
|
|
|
|
-- BFD General Variables
|
|
|
|
-- These parameters apply globally to the Router's
|
|
-- BFD Process.
|
|
|
|
bfdAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
-- MAX-ACCESS read-write
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The global administrative status of BFD in this router.
|
|
The value 'enabled' denotes that the BFD Process is
|
|
active on at least one interface; 'disabled' disables
|
|
it on all interfaces."
|
|
DEFVAL { enabled }
|
|
::= { bfdScalarObjects 1 }
|
|
|
|
bfdVersionNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The current version number of the BFD protocol."
|
|
REFERENCE
|
|
" BFD Version 0 (draft-katz-ward-bfd-02.txt)"
|
|
DEFVAL { 0 }
|
|
::= { bfdScalarObjects 3 }
|
|
|
|
|
|
-- BFD Session Table
|
|
-- The BFD Session Table specifies BFD session specific
|
|
-- information.
|
|
|
|
bfdSessTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Table describes the BFD sessions."
|
|
REFERENCE
|
|
"BFD Version 0 (draft-katz-ward-bfd-02.txt)"
|
|
::= { bfdObjects 2 }
|
|
|
|
bfdSessEntry OBJECT-TYPE
|
|
SYNTAX BfdSessEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Entry describes BFD session."
|
|
INDEX { bfdSessIndex }
|
|
::= { bfdSessTable 1 }
|
|
|
|
BfdSessEntry ::= SEQUENCE {
|
|
bfdSessIndex BfdSessIndexTC,
|
|
bfdSessApplicationId Unsigned32,
|
|
bfdSessDiscriminator Unsigned32,
|
|
bfdSessRemoteDiscr Unsigned32,
|
|
bfdSessUdpPort InetPortNumber,
|
|
bfdSessState INTEGER,
|
|
bfdSessRemoteHeardFlag TruthValue,
|
|
bfdSessDiag Unsigned32,
|
|
bfdSessOperMode INTEGER,
|
|
bfdSessDemandModeDesiredFlag TruthValue,
|
|
bfdSessEchoFuncModeDesiredFlag TruthValue,
|
|
bfdSessControlPlanIndepFlag TruthValue,
|
|
bfdSessAddrType InetAddressType,
|
|
bfdSessAddr InetAddress,
|
|
bfdSessDesiredMinTxInterval BfdInterval,
|
|
bfdSessDesiredMinRxInterval BfdInterval,
|
|
bfdSessDesiredMinEchoRxInterval BfdInterval,
|
|
bfdSessDetectMult Unsigned32,
|
|
bfdSessStorType StorageType,
|
|
bfdSessRowStatus RowStatus,
|
|
bfdSessAuthPresFlag TruthValue,
|
|
bfdSessAuthenticationType INTEGER
|
|
}
|
|
|
|
bfdSessIndex OBJECT-TYPE
|
|
SYNTAX BfdSessIndexTC
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains an index used to represent a
|
|
unique BFD session on this device."
|
|
::= { bfdSessEntry 1 }
|
|
|
|
bfdSessApplicationId OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains an index used to indicate
|
|
a local application which owns or maintains this
|
|
BFD session. For instance, the MPLS VPN process may
|
|
maintain a subset of the total number of BFD
|
|
sessions. This application ID provides a convenient
|
|
way to segregate sessions by the applications which
|
|
maintain them."
|
|
::= { bfdSessEntry 2 }
|
|
|
|
bfdSessDiscriminator OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the local discriminator for this BFD
|
|
session, used to uniquely identify it."
|
|
::= { bfdSessEntry 3 }
|
|
|
|
bfdSessRemoteDiscr OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the session discriminator chosen
|
|
by the remote system for this BFD session."
|
|
::= { bfdSessEntry 4 }
|
|
|
|
bfdSessUdpPort OBJECT-TYPE
|
|
SYNTAX InetPortNumber
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The UDP Port for BFD. The default value is the
|
|
well-known value for this port."
|
|
REFERENCE
|
|
"draft-katz-ward-bfd-02.txt and
|
|
draft-raggarwa-mpls-bfd-00.txt"
|
|
DEFVAL { 0 }
|
|
::= { bfdSessEntry 5 }
|
|
|
|
bfdSessState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
adminDown(1),
|
|
down(2),
|
|
init(3),
|
|
up(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The perceived state of the BFD session."
|
|
::= { bfdSessEntry 6 }
|
|
|
|
bfdSessRemoteHeardFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies status of BFD packet reception from
|
|
the remote system. Specifically, it is set to true(1) if
|
|
the local system is actively receiving BFD packets from the
|
|
remote system, and is set to false(0) if the local system
|
|
has not received BFD packets recently (within the detection
|
|
time) or if the local system is attempting to tear down
|
|
the BFD session."
|
|
::= { bfdSessEntry 7 }
|
|
|
|
bfdSessDiag OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A diagnostic code specifying the local system's reason
|
|
for the last transition of the session from up(1)
|
|
to some other state."
|
|
::= { bfdSessEntry 8 }
|
|
|
|
bfdSessOperMode OBJECT-TYPE
|
|
SYNTAX INTEGER { asyncModeWEchoFun(1),
|
|
asynchModeWOEchoFun(2),
|
|
demandModeWEchoFunction(3),
|
|
demandModeWOEchoFunction(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies current operating mode that BFD
|
|
session is operating in.
|
|
|
|
A value of AsyncModeWEchoFun(1) ...
|
|
A value of AsynchModeWOEchoFun(2) ...
|
|
A value of DemandModeWEchoFunction(3) ...
|
|
A value of DemandModeWOEchoFunction(4) ...
|
|
"
|
|
::= { bfdSessEntry 9 }
|
|
|
|
bfdSessDemandModeDesiredFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
desire to use Demand mode. Specifically, it is set
|
|
to true(1) if the local system wishes to use
|
|
Demand mode or false(0) if not"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 10 }
|
|
|
|
bfdSessEchoFuncModeDesiredFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
desire to use Echo mode. Specifically, it is set
|
|
to true(1) if the local system wishes to use
|
|
Echo mode or false(0) if not"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 11 }
|
|
|
|
bfdSessControlPlanIndepFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
ability to continue to function through a disruption of
|
|
the control plane. Specifically, it is set
|
|
to true(1) if the local system BFD implementation is
|
|
independent of the control plane. Otherwise, the
|
|
value is set to false(0)"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 12 }
|
|
|
|
bfdSessAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies IP address of the interface
|
|
associated with this BFD session.
|
|
|
|
Only values unknown(0), ipv4(1) or ipv6(2)
|
|
have to be supported.
|
|
|
|
A value of unknown(0) is allowed only when
|
|
the outgoing interface is of type point-to-point, or
|
|
when the BFD session is not associated with a specific
|
|
interface.
|
|
|
|
If any other unsupported values are attempted in a set
|
|
operation, the agent MUST return an inconsistentValue
|
|
error.
|
|
"
|
|
::= { bfdSessEntry 13 }
|
|
|
|
bfdSessAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies IP address of the interface
|
|
associated with this BFD session.
|
|
It can also be used to enabled BFD on a specific
|
|
interface. The value is set to zero when BFD session is not
|
|
associated with a specific interface. "
|
|
::= { bfdSessEntry 14 }
|
|
|
|
bfdSessDesiredMinTxInterval OBJECT-TYPE
|
|
SYNTAX BfdInterval
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, that the local system would like to use when
|
|
transmitting BFD Control packets."
|
|
::= { bfdSessEntry 15 }
|
|
|
|
bfdSessDesiredMinRxInterval OBJECT-TYPE
|
|
SYNTAX BfdInterval
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, between received BFD Control packets the
|
|
local system is capable of supporting."
|
|
::= { bfdSessEntry 16 }
|
|
|
|
bfdSessDesiredMinEchoRxInterval OBJECT-TYPE
|
|
SYNTAX BfdInterval
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, between received BFD Echo packets that this
|
|
system is capable of supporting."
|
|
::= { bfdSessEntry 17 }
|
|
|
|
bfdSessDetectMult OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Detect time multiplier."
|
|
::= { bfdSessEntry 18 }
|
|
|
|
bfdSessStorType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the storage type for this
|
|
object. Conceptual rows having the value
|
|
'permanent' need not allow write-access to any
|
|
columnar objects in the row."
|
|
::= { bfdSessEntry 19 }
|
|
|
|
bfdSessRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable is used to create, modify, and/or
|
|
delete a row in this table. When a row in this
|
|
table has a row in the active(1) state, no
|
|
objects in this row can be modified except the
|
|
bfdSessRowStatus and bfdSessStorageType."
|
|
::= { bfdSessEntry 20 }
|
|
|
|
bfdSessAuthPresFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
desire to use Authentication. Specifically, it is set
|
|
to true(1) if the local system wishes the session
|
|
to be authenticated or false(0) if not"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 21 }
|
|
|
|
bfdSessAuthenticationType OBJECT-TYPE
|
|
SYNTAX INTEGER { simplePassword(1),
|
|
keyedMD5(2),
|
|
meticulousKeyedMD5(3),
|
|
keyedSHA1(4),
|
|
meticulousKeyedSHA1(5)
|
|
}
|
|
-- MAX-ACCESS read-create
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Authentication Type used for this BFD session. This
|
|
field is valid only when the Authentication Present bit is set"
|
|
::= { bfdSessEntry 22 }
|
|
|
|
-- BFD Session Performance Table
|
|
|
|
bfdSessPerfTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessPerfEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table specifies BFD Session performance counters."
|
|
::= { bfdObjects 3 }
|
|
|
|
bfdSessPerfEntry OBJECT-TYPE
|
|
SYNTAX BfdSessPerfEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry in this table is created by a BFD-enabled node for
|
|
every BFD Session. bfdCounterDiscontinuityTime is used to
|
|
indicate potential discontinuity for all counter objects
|
|
in this table."
|
|
AUGMENTS { bfdSessEntry }
|
|
::= { bfdSessPerfTable 1 }
|
|
|
|
BfdSessPerfEntry ::= SEQUENCE {
|
|
bfdSessPerfPktIn Counter32,
|
|
bfdSessPerfPktOut Counter32,
|
|
bfdSessUpTime TimeStamp,
|
|
bfdSessPerfLastSessDownTime TimeStamp,
|
|
bfdSessPerfLastCommLostDiag BfdDiag,
|
|
bfdSessPerfSessUpCount Counter32,
|
|
bfdSessPerfDiscTime TimeStamp,
|
|
|
|
-- High Capacity Counters
|
|
bfdSessPerfPktInHC Counter64,
|
|
bfdSessPerfPktOutHC Counter64
|
|
}
|
|
|
|
-- Ed Note: should we add per-diag code counts here,
|
|
|
|
bfdSessPerfPktIn OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD messages received for this BFD
|
|
session."
|
|
::= { bfdSessPerfEntry 1 }
|
|
|
|
bfdSessPerfPktOut OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD messages sent for this BFD session."
|
|
::= { bfdSessPerfEntry 2 }
|
|
|
|
bfdSessUpTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at which
|
|
the session came up. If no such up event exists this object
|
|
contains a zero value."
|
|
::= { bfdSessPerfEntry 3 }
|
|
|
|
bfdSessPerfLastSessDownTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at which
|
|
the last time communication was lost with the neighbor. If
|
|
no such down event exist this object contains a zero value."
|
|
::= { bfdSessPerfEntry 4 }
|
|
|
|
bfdSessPerfLastCommLostDiag OBJECT-TYPE
|
|
SYNTAX BfdDiag
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD diag code for the last time communication was lost
|
|
with the neighbor. If no such down event exists this object
|
|
contains a zero value."
|
|
::= { bfdSessPerfEntry 5 }
|
|
|
|
bfdSessPerfSessUpCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of times this session has gone into the Up
|
|
state since the router last rebooted."
|
|
::= { bfdSessPerfEntry 6 }
|
|
|
|
bfdSessPerfDiscTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at
|
|
which any one or more of the session counters suffered
|
|
a discontinuity.
|
|
|
|
The relevant counters are the specific instances associated
|
|
with this BFD session of any Counter32 object contained in
|
|
the BfdSessPerfTable. If no such discontinuities have occurred
|
|
since the last re-initialization of the local management
|
|
subsystem, then this object contains a zero value."
|
|
::= { bfdSessPerfEntry 7 }
|
|
|
|
bfdSessPerfPktInHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD messages
|
|
received for this BFD session. It MUST be equal to the
|
|
least significant 32 bits of bfdSessPerfPktIn
|
|
if bfdSessPerfPktInHC is supported according to
|
|
the rules spelled out in RFC2863."
|
|
::= { bfdSessPerfEntry 8 }
|
|
|
|
bfdSessPerfPktOutHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of
|
|
total number of BFD messages transmitted for this
|
|
BFD session. It MUST be equal to the
|
|
least significant 32 bits of bfdSessPerfPktIn
|
|
if bfdSessPerfPktOutHC is supported according to
|
|
the rules spelled out in RFC2863."
|
|
::= { bfdSessPerfEntry 9 }
|
|
|
|
|
|
-- BFD Session Mapping Table
|
|
|
|
bfdSessMapTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Mapping Table maps the complex
|
|
indexing of the BFD sessions to the flat
|
|
BFDIndex used in the BfdSessionTable.
|
|
|
|
Implementors need to be aware that if the value of
|
|
the bfdSessAddr (an OID) has more
|
|
that 111 sub-identifiers, then OIDs of column
|
|
instances in this table will have more than 128
|
|
sub-identifiers and cannot be accessed using SNMPv1,
|
|
SNMPv2c, or SNMPv3.
|
|
"
|
|
REFERENCE
|
|
"BFD Version 0 (draft-katz-ward-bfd-02.txt)"
|
|
::= { bfdObjects 4 }
|
|
|
|
bfdSessMapEntry OBJECT-TYPE
|
|
SYNTAX BfdSessMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Entry describes BFD session
|
|
that is mapped to this index.
|
|
|
|
Implementors need to be aware that if the value of
|
|
the mplsInSegmentMapLabelPtrIndex (an OID) has more
|
|
that 111 sub-identifiers, then OIDs of column
|
|
instances in this table will have more than 128
|
|
sub-identifiers and cannot be accessed using SNMPv1,
|
|
SNMPv2c, or SNMPv3."
|
|
INDEX { bfdSessApplicationId,
|
|
bfdSessDiscriminator,
|
|
bfdSessAddrType,
|
|
bfdSessAddr
|
|
}
|
|
::= { bfdSessMapTable 1 }
|
|
|
|
BfdSessMapEntry ::= SEQUENCE {
|
|
bfdSessMapBfdIndex BfdSessIndexTC
|
|
}
|
|
|
|
bfdSessMapBfdIndex OBJECT-TYPE
|
|
SYNTAX BfdSessIndexTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the BfdIndex referred to by
|
|
the indexes of this row. In essence, a mapping is
|
|
provided between these indexes and the BfdSessTable."
|
|
::= { bfdSessMapEntry 1 }
|
|
|
|
-- Notification Configuration
|
|
|
|
bfdSessNotificationsEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
-- MAX-ACCESS read-write
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If this object is set to true(1), then it enables
|
|
the emission of bfdSessUp and bfdSessDown
|
|
notifications; otherwise these notifications are not
|
|
emitted."
|
|
REFERENCE
|
|
"See also RFC3413 for explanation that
|
|
notifications are under the ultimate control of the
|
|
MIB modules in this document."
|
|
DEFVAL { false }
|
|
::= { bfdScalarObjects 4 }
|
|
|
|
bfdSessUp NOTIFICATION-TYPE
|
|
OBJECTS { bfdSessDiag, -- low range value
|
|
bfdSessDiag -- high range value
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the
|
|
bfdSessState object for one or more contiguous
|
|
entries in bfdSessTable are about to enter the up(2)
|
|
state from some other state. The included values of
|
|
bfdSessDiag MUST both be set equal to this
|
|
new state (i.e: up(1)). The two instances of
|
|
bfdSessDiag in this notification indicate the range
|
|
of indexes that are affected. Note that all the indexes
|
|
of the two ends of the range can be derived from the
|
|
instance identifiers of these two objects. For the
|
|
cases where a contiguous range of sessions
|
|
have transitioned into the up(1) state at roughly
|
|
the same time, the device SHOULD issue a single
|
|
notification for each range of contiguous indexes in
|
|
an effort to minimize the emission of a large number
|
|
of notifications. If a notification has to be
|
|
issued for just a single bfdSessEntry, then
|
|
the instance identifier (and values) of the two
|
|
bfdSessDiag objects MUST be the identical."
|
|
::= { bfdNotifications 1 }
|
|
|
|
bfdSessDown NOTIFICATION-TYPE
|
|
OBJECTS { bfdSessDiag, -- low range value
|
|
bfdSessDiag -- high range value
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the
|
|
bfdSessState object for one or more contiguous
|
|
entries in bfdSessTable are about to enter the down(4)
|
|
or adminDown(5) states from some other state. The included
|
|
values of bfdSessDiag MUST both be set equal to this
|
|
new state (i.e: down(4) or adminDown(5)). The two instances
|
|
of bfdSessDiag in this notification indicate the range
|
|
of indexes that are affected. Note that all the indexes
|
|
of the two ends of the range can be derived from the
|
|
instance identifiers of these two objects. For
|
|
cases where a contiguous range of sessions
|
|
have transitioned into the down(4) or adminDown(5) states
|
|
at roughly the same time, the device SHOULD issue a single
|
|
notification for each range of contiguous indexes in
|
|
an effort to minimize the emission of a large number
|
|
of notifications. If a notification has to be
|
|
issued for just a single bfdSessEntry, then
|
|
the instance identifier (and values) of the two
|
|
bfdSessDiag objects MUST be the identical."
|
|
::= { bfdNotifications 2 }
|
|
|
|
-- Ed Note: We need to add notification for changes
|
|
-- when the two ends automatically negotiate to a new detection time
|
|
-- value or when detection multiplier changes.
|
|
-- Similarly, changes in the operating mode (bfdSessOperMode)
|
|
-- also need to be notified.
|
|
|
|
-- Module compliance.
|
|
|
|
bfdGroups
|
|
OBJECT IDENTIFIER ::= { bfdConformance 1 }
|
|
|
|
bfdCompliances
|
|
OBJECT IDENTIFIER ::= { bfdConformance 2 }
|
|
|
|
-- Compliance requirement for fully compliant implementations.
|
|
|
|
bfdModuleFullCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION "Compliance statement for agents that provide full
|
|
support for BFD-MIB. Such devices can
|
|
then be monitored and also be configured using
|
|
this MIB module."
|
|
|
|
MODULE -- This module.
|
|
MANDATORY-GROUPS {
|
|
bfdSessionGroup,
|
|
bfdSessionPerfGroup,
|
|
bfdSessionPerfHCGroup,
|
|
bfdNotificationGroup
|
|
}
|
|
|
|
-- GROUP bfdSessionPerfHCGroup
|
|
-- DESCRIPTION "This group is mandatory for those bfdPerfTable
|
|
-- entries for which any of the objects
|
|
-- bfdSessPerfPktInHC or bfdSessPerfPktOutHC
|
|
-- wraps around too quickly
|
|
-- based on the criteria specified in RFC 2863 for
|
|
-- high-capacity counters."
|
|
--
|
|
-- GROUP bfdNotificationGroup
|
|
-- DESCRIPTION "This group is only mandatory for those
|
|
-- implementations which can efficiently implement
|
|
-- the notifications contained in this group."
|
|
--
|
|
OBJECT bfdSessAddrType
|
|
SYNTAX InetAddressType {
|
|
unknown(0),
|
|
ipv4(1),
|
|
ipv6(2)
|
|
}
|
|
DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support
|
|
is required."
|
|
|
|
OBJECT bfdSessAddr
|
|
SYNTAX InetAddress (SIZE(0|4|16))
|
|
DESCRIPTION "An implementation is only required to support
|
|
unknown(0), ipv4(1) and ipv6(2) sizes."
|
|
|
|
::= { bfdCompliances 1 }
|
|
|
|
-- Read-Only Conformance TBD...
|
|
|
|
|
|
-- Units of conformance.
|
|
|
|
bfdSessionGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessNotificationsEnable,
|
|
bfdAdminStatus,
|
|
bfdVersionNumber,
|
|
bfdSessApplicationId,
|
|
bfdSessDiscriminator,
|
|
bfdSessAddrType,
|
|
bfdSessAddr,
|
|
bfdSessRemoteDiscr,
|
|
bfdSessUdpPort,
|
|
bfdSessState,
|
|
bfdSessRemoteHeardFlag,
|
|
bfdSessDiag,
|
|
bfdSessOperMode,
|
|
bfdSessDemandModeDesiredFlag,
|
|
bfdSessEchoFuncModeDesiredFlag,
|
|
bfdSessControlPlanIndepFlag,
|
|
bfdSessDesiredMinTxInterval,
|
|
bfdSessDesiredMinRxInterval,
|
|
bfdSessDesiredMinEchoRxInterval,
|
|
bfdSessDetectMult,
|
|
bfdSessStorType,
|
|
bfdSessRowStatus,
|
|
bfdSessMapBfdIndex,
|
|
bfdSessAuthPresFlag,
|
|
bfdSessAuthenticationType
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed for BFD sessions."
|
|
::= { bfdGroups 1 }
|
|
|
|
|
|
bfdSessionPerfGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessPerfPktIn,
|
|
bfdSessPerfPktOut,
|
|
bfdSessUpTime,
|
|
bfdSessPerfLastSessDownTime,
|
|
bfdSessPerfLastCommLostDiag,
|
|
bfdSessPerfSessUpCount,
|
|
bfdSessPerfDiscTime
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed to monitor the
|
|
performance of BFD sessions."
|
|
::= { bfdGroups 2 }
|
|
|
|
bfdSessionPerfHCGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessPerfPktInHC,
|
|
bfdSessPerfPktOutHC
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed to monitor the
|
|
performance of BFD sessions for which the
|
|
values of bfdSessPerfPktIn, bfdSessPerfPktOut
|
|
wrap around too quickly."
|
|
::= { bfdGroups 3 }
|
|
|
|
bfdNotificationGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
bfdSessUp,
|
|
bfdSessDown
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set of notifications implemented in this
|
|
module."
|
|
|
|
::= { bfdGroups 4 }
|
|
|
|
END
|
|
|