mibs/MIBS/mitsubishi/UPS-MIB
2023-12-05 12:25:34 +01:00

1185 lines
38 KiB
Plaintext

-- Mitsubishi.mib - MIB file for Mitsubishi UPSs
UPS-MIB DEFINITIONS ::= BEGIN
IMPORTS
TRAP-TYPE
FROM RFC-1215
DisplayString
FROM RFC1213-MIB
OBJECT-TYPE
FROM RFC-1212
Gauge, Counter, TimeTicks, mgmt
FROM RFC1155-SMI
;
PositiveInteger ::= INTEGER
NonNegativeInteger ::= INTEGER
TimeStamp ::= TimeTicks
TimeInterval ::= INTEGER (0..2147483647)
TestAndIncr ::= INTEGER (0..2147483647)
AutonomousType ::= DisplayString
Tag OBJECT IDENTIFIER ::= { enterprises 13891 }
MitsubishiUPS OBJECT IDENTIFIER ::= { Tag 101 }
upsIdent OBJECT IDENTIFIER ::= { MitsubishiUPS 1 }
upsIdentManufacturer OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of the UPS manufacturer."
::= { upsIdent 1 }
upsIdentModel OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS Model designation."
::= { upsIdent 2 }
upsIdentUPSSoftwareVersion OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS firmware/software version(s). This variable
may or may not have the same value as
upsIdentAgentSoftwareVersion in some implementations."
::= { upsIdent 3 }
upsIdentAgentSoftwareVersion OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS agent software version. This variable may or may
not have the same value as upsIdentUPSSoftwareVersion in
some implementations."
::= { upsIdent 4 }
upsIdentName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string identifying the UPS. This object should be
set by the administrator."
::= { upsIdent 5 }
upsIdentAttachedDevices OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string identifying the devices attached to the output
of the UPS. This object should be set by the administrator."
::= { upsIdent 6 }
upsBattery OBJECT IDENTIFIER ::= { MitsubishiUPS 2 }
upsBatteryStatus OBJECT-TYPE
SYNTAX INTEGER
{
unknown(1),
batteryNormal(2),
batteryLow(3),
batteryDepleted(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The indication of the capacity remaining in the UPS batteries.
A value of batteryNormal indicates a normal battery condition.
A value of batteryLow indicates the remaining battery run-time
will not maintain the output load for an extended period of time.
A value of batteryDepleted indicates that the UPS will be unable
to sustain the present load when and if the utility power is lost."
::= { upsBattery 1 }
upsSecondsOnBattery OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS seconds
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If the unit is on battery power, the elapsed time in seconds
since the UPS last switched to battery power, or the time since
the network management system was last restarted, whichever is less.
Zero shall be returned if the unit is not on battery power."
::= { upsBattery 2 }
upsEstimatedMinutesRemaining OBJECT-TYPE
SYNTAX PositiveInteger -- UNITS minutes
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An estimate of the time in minutes until the battery is depleted
under the present load conditions if the utility power is off and
remains off, or if it were to be lost and remain off."
::= { upsBattery 3 }
upsEstimatedChargeRemaining OBJECT-TYPE
SYNTAX INTEGER -- UNITS percent
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An estimate of the battery charge remaining expressed as a
percent of full charge."
::= { upsBattery 4 }
upsBatteryVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Volt DC
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the present battery voltage (0.1 Volt DC)."
::= { upsBattery 5 }
upsBatteryCurrent OBJECT-TYPE
SYNTAX INTEGER (-2147483648..2147483647) -- UNITS 0.1 Amp DC
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present battery current (0.1 Amp DC)."
::= { upsBattery 6 }
upsBatteryTemperature OBJECT-TYPE
SYNTAX INTEGER (-2147483648..2147483647) -- UNITS degrees Centigrade
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ambient temperature at or near the UPS Battery casing (degrees Centigrade)."
::= { upsBattery 7 }
upsInput OBJECT IDENTIFIER ::= { MitsubishiUPS 3 }
upsInputLineBads OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the number of times the input entered an
out-of-tolerance condition as defined by the manufacturer.
This count is incremented by one each time the input
transitions from zero out-of-tolerance lines to one or more
input lines out-of-tolerance."
::= { upsInput 1 }
upsInputNumLines OBJECT-TYPE
SYNTAX NonNegativeInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of input lines utilized in this device. This
variable indicates the number of rows in the input table."
::= { upsInput 2 }
upsInputTable OBJECT-TYPE
SYNTAX SEQUENCE OF UpsInputEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of input table entries. The number of entries
is given by the value of upsInputNumLines."
::= { upsInput 3 }
upsInputEntry OBJECT-TYPE
SYNTAX UpsInputEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry containing information applicable to a
particular input line."
INDEX { upsInputLineIndex }
::= { upsInputTable 1 }
UpsInputEntry ::=
SEQUENCE
{
upsInputLineIndex PositiveInteger,
upsInputFrequency NonNegativeInteger,
upsInputVoltage NonNegativeInteger,
upsInputCurrent NonNegativeInteger,
upsInputTruePower NonNegativeInteger
}
upsInputLineIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The input line identifier."
::= { upsInputEntry 1 }
upsInputFrequency OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Hertz
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present input frequency (0.1 Hertz)."
::= { upsInputEntry 2 }
upsInputVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Volt
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the present input voltage (0.1 RMS Volt)."
::= { upsInputEntry 3 }
upsInputCurrent OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Amp
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the present input current (0.1 RMS Amp)."
::= { upsInputEntry 4 }
upsInputTruePower OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS Watts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the present input true power (watts)."
::= { upsInputEntry 5 }
upsOutput OBJECT IDENTIFIER ::= { MitsubishiUPS 4 }
upsOutputSource OBJECT-TYPE
SYNTAX INTEGER
{
other(1),
none(2),
normal(3),
bypass(4),
battery(5),
booster(6),
reducer(7)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present source of output power. A value of none (2) indicates
there is no source of output power (and therefore no output power),
for example, the system has opened the output breaker."
::= { upsOutput 1 }
upsOutputFrequency OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Hertz
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present output frequency (0.1 Hertz)."
::= { upsOutput 2 }
upsOutputNumLines OBJECT-TYPE
SYNTAX NonNegativeInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of output lines utilized in this device. This
variable indicates the number of rows in the output table."
::= { upsOutput 3 }
upsOutputTable OBJECT-TYPE
SYNTAX SEQUENCE OF UpsOutputEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of output table entries. The number of
entries is given by the value of upsOutputNumLines."
::= { upsOutput 4 }
upsOutputEntry OBJECT-TYPE
SYNTAX UpsOutputEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry containing information applicable to a
particular output line."
INDEX { upsOutputLineIndex }
::= { upsOutputTable 1 }
UpsOutputEntry ::=
SEQUENCE
{
upsOutputLineIndex PositiveInteger,
upsOutputVoltage NonNegativeInteger,
upsOutputCurrent NonNegativeInteger,
upsOutputPower NonNegativeInteger,
upsOutputPercentLoad INTEGER
}
upsOutputLineIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The output line identifier."
::= { upsOutputEntry 1 }
upsOutputVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Volts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present output voltage (0.1 RMS Volt)."
::= { upsOutputEntry 2 }
upsOutputCurrent OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Amp
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present output current (0.1 RMS Amp)."
::= { upsOutputEntry 3 }
upsOutputPower OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS Watts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present output true power (watts)."
::= { upsOutputEntry 4 }
upsOutputPercentLoad OBJECT-TYPE
SYNTAX INTEGER -- UNITS percent
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The percentage of the UPS power capacity presently being
used on this output line (the greater of the percent load
of true power capacity and the percent load of VA."
::= { upsOutputEntry 5 }
upsBypass OBJECT IDENTIFIER ::= { MitsubishiUPS 5 }
upsBypassFrequency OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Hertz
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present bypass frequency."
::= { upsBypass 1 }
upsBypassNumLines OBJECT-TYPE
SYNTAX NonNegativeInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of bypass lines utilized in this device. This
entry indicates the number of rows in the bypass table."
::= { upsBypass 2 }
upsBypassTable OBJECT-TYPE
SYNTAX SEQUENCE OF UpsBypassEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of bypass table entries. The number of entries
is given by the value of upsBypassNumLines."
::= { upsBypass 3 }
upsBypassEntry OBJECT-TYPE
SYNTAX UpsBypassEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry containing information applicable to a
particular bypass input."
INDEX { upsBypassLineIndex }
::= { upsBypassTable 1 }
UpsBypassEntry ::=
SEQUENCE
{
upsBypassLineIndex PositiveInteger,
upsBypassVoltage NonNegativeInteger,
upsBypassCurrent NonNegativeInteger,
upsBypassPower NonNegativeInteger
}
upsBypassLineIndex OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The bypass line identifier."
::= { upsBypassEntry 1 }
upsBypassVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Volts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present bypass voltage (0.1 RMS Volt)."
::= { upsBypassEntry 2 }
upsBypassCurrent OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 RMS Amp
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present bypass current (0.1 RMS Amp)."
::= { upsBypassEntry 3 }
upsBypassPower OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS Watts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present true power conveyed by the bypass (watts)."
::= { upsBypassEntry 4 }
upsAlarm OBJECT IDENTIFIER ::= { MitsubishiUPS 6 }
upsAlarmsPresent OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present number of active alarm conditions."
::= { upsAlarm 1 }
upsAlarmTable OBJECT-TYPE
SYNTAX SEQUENCE OF UpsAlarmEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of alarm table entries. Alarms are named by
an OBJECT IDENTIFIER, upsAlarmDescr, to allow a single
table to reflect well known alarms plus alarms defined
by a particular implementation, i.e., as documented in
the private enterprise MIB definition for the device.
No two rows will have the same value of upsAlarmDescr,
since alarms define conditions. In order to meet this
requirement, care should be taken in the definition of
alarm conditions to insure that a system cannot enter
the same condition multiple times simultaneously.
The number of rows in the table at any given time is
reflected by the value of upsAlarmsPresent."
::= { upsAlarm 2 }
upsAlarmEntry OBJECT-TYPE
SYNTAX UpsAlarmEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry containing information applicable to a
particular alarm."
INDEX { upsAlarmId }
::= { upsAlarmTable 1 }
UpsAlarmEntry ::=
SEQUENCE
{
upsAlarmId PositiveInteger,
upsAlarmDescr AutonomousType,
upsAlarmTime TimeStamp
}
upsAlarmId OBJECT-TYPE
SYNTAX PositiveInteger
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique identifier for an alarm condition. This
value must remain constant."
::= { upsAlarmEntry 1 }
upsAlarmDescr OBJECT-TYPE
SYNTAX AutonomousType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A reference to an alarm description object. The object
referenced should not be accessible, but rather be used
to provide a unique description of the alarm condition."
::= { upsAlarmEntry 2 }
upsAlarmTime OBJECT-TYPE
SYNTAX TimeStamp
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime when the alarm condition was
detected. If the alarm condition was detected at the
time of agent startup and presumably existed before
agent startup, the value of upsAlarmTime shall equal 0."
::= { upsAlarmEntry 3 }
upsAlarmID OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique identifier for an alarm condition. This
value must remain constant."
::= { upsAlarm 4 }
upsAlarmDESCR OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..63))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A reference to an alarm description object. The object
references should not be accessible, but rather be used
to provide a unique description of the alarm condition."
::= { upsAlarm 5 }
upsWellKnownAlarms OBJECT IDENTIFIER ::= { upsAlarm 3 }
upsAlarmBatteryBad OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"One or more batteries have been determined to require
replacement."
::= { upsWellKnownAlarms 1 }
upsAlarmOnBattery OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS is drawing power from the batteries."
::= { upsWellKnownAlarms 2 }
upsAlarmLowBattery OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The remaining battery run-time is less than or equal
to upsConfigLowBattTime."
::= { upsWellKnownAlarms 3 }
upsAlarmDepletedBattery OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS will be unable to sustain the present load
when and if the utility power is lost."
::= { upsWellKnownAlarms 4 }
upsAlarmTempBad OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A temperature is out of tolerance."
::= { upsWellKnownAlarms 5 }
upsAlarmInputBad OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An input condition is out of tolerance."
::= { upsWellKnownAlarms 6 }
upsAlarmOutputBad OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An output condition (other than OutputOverload) is
out of tolerance."
::= { upsWellKnownAlarms 7 }
upsAlarmOutputOverload OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The output load exceeds the UPS output capacity."
::= { upsWellKnownAlarms 8 }
upsAlarmOnBypass OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Bypass is presently engaged on the UPS."
::= { upsWellKnownAlarms 9 }
upsAlarmBypassBad OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Bypass is out of tolerance."
::= { upsWellKnownAlarms 10 }
upsAlarmOutputOffAsRequested OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS has shut down as requested, i.e., the output
is off."
::= { upsWellKnownAlarms 11 }
upsAlarmUpsOffAsRequested OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The entire UPS has shutdown as commanded."
::= { upsWellKnownAlarms 12 }
upsAlarmChargerFailed OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An uncorrected problem has been detected within the
UPS charger subsystem."
::= { upsWellKnownAlarms 13 }
upsAlarmUpsOutputOff OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The output of the UPS is in the off state."
::= { upsWellKnownAlarms 14 }
upsAlarmUpsSystemOff OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS system is in the off state."
::= { upsWellKnownAlarms 15 }
upsAlarmFanFailure OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The failure of one or more fans in the UPS has been
detected."
::= { upsWellKnownAlarms 16 }
upsAlarmFuseFailure OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The failure of one or more fuses has been detected."
::= { upsWellKnownAlarms 17 }
upsAlarmGeneralFault OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A general fault in the UPS has been detected."
::= { upsWellKnownAlarms 18 }
upsAlarmDiagnosticTestFailed OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The result of the last diagnostic test indicates a
failure."
::= { upsWellKnownAlarms 19 }
upsAlarmCommunicationsLost OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A problem has been encountered in the
communications between the agent and the UPS."
::= { upsWellKnownAlarms 20 }
upsAlarmAwaitingPower OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS output is off and the UPS is awaiting the
return of input power."
::= { upsWellKnownAlarms 21 }
upsAlarmShutdownPending OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A upsShutdownAfterDelay countdown is underway."
::= { upsWellKnownAlarms 22 }
upsAlarmShutdownImminent OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UPS will turn off power to the load in less than
5 seconds; this may be either a timed shutdown or a
low battery shutdown."
::= { upsWellKnownAlarms 23 }
upsAlarmTestInProgress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A test is in progress, as initiated and indicated by
the Test Group. Tests initiated via other
implementation-specific mechanisms can indicate the
presence of the testing in the alarm table, if
desired, via a OBJECT-TYPE macro in the MIB
document specific to that implementation and are
outside the scope of this OBJECT-TYPE."
::= { upsWellKnownAlarms 24 }
upsTest OBJECT IDENTIFIER ::= { MitsubishiUPS 7 }
upsTestId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The test named by an OBJECT IDENTIFIER which
allows a standard mechanism for the initiation of
a test, including the well known tests identified in
this document."
::= { upsTest 1 }
upsTestSpinLock OBJECT-TYPE
SYNTAX TestAndIncr
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A spin lock on the test subsystem."
::= { upsTest 2 }
upsTestResultsSummary OBJECT-TYPE
SYNTAX INTEGER
{
donePass(1),
doneWarning(2),
doneError(3),
aborted(4),
inProgress(5),
noTestsInitiated(6)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The results of the current or last UPS diagnostics
test performed. The values for donePass(1),
doneWarning(2), and doneError(3) indicate that the
test completed either successfully, with a warning, or
with an error, respectively. The value aborted(4) is
returned for tests which are aborted by setting the
value of upsTestId to upsTestAbortTestInProgress.
Tests which have not yet concluded are indicated by
inProgress(5). The value noTestsInitiated(6)
indicates that no previous test results are available,
such as is the case when no tests have been run since
the last reinitialization of the network management
subsystem and the system has no provision for non-
volatile storage of test results."
::= { upsTest 3 }
upsTestResultsDetail OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Additional information about upsTestResultsSummary.
If no additional information available, a zero length
string is returned."
::= { upsTest 4 }
upsTestStartTime OBJECT-TYPE
SYNTAX TimeStamp
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime at the time the test in
progress was initiated, or, if no test is in progress,
the time the previous test was initiated. If the
value of upsTestResultsSummary is noTestsInitiated(6),
upsTestStartTime has the value 0."
::= { upsTest 5 }
upsTestElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The amount of time, in TimeTicks, since the test in
progress was initiated, or, if no test is in progress,
the previous test took to complete. If the value of
upsTestResultsSummary is noTestsInitiated(6),
upsTestElapsedTime has the value 0."
::= { upsTest 6 }
upsWellKnownTests OBJECT IDENTIFIER ::= { upsTest 7 }
upsTestNoTestsInitiated OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"No tests have been initiated and no test is in progress."
::= { upsWellKnownTests 1 }
upsTestAbortTestInProgress OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The test in progress is to be aborted / the test in
progress was aborted."
::= { upsWellKnownTests 2 }
upsTestGeneralSystemsTest OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The manufacturer's standard test of UPS device systems."
::= { upsWellKnownTests 3 }
upsTestQuickBatteryTest OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A test that is sufficient to determine if the battery
needs replacement."
::= { upsWellKnownTests 4 }
upsTestDeepBatteryCalibration OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The system is placed on battery to a discharge level,
set by the manufacturer, sufficient to determine
battery replacement and battery run-time with a high
degree of confidence. WARNING: this test will leave
the battery in a low charge state and will require
time for recharging to a level sufficient to provide
normal battery duration for the protected load."
::= { upsWellKnownTests 5 }
upsControl OBJECT IDENTIFIER ::= { MitsubishiUPS 8 }
upsShutdownType OBJECT-TYPE
SYNTAX INTEGER
{
output(1),
system(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object determines the nature of the action to be
taken at the time when the countdown of the
upsShutdownAfterDelay and upsRebootWithDuration
objects reaches zero.
Setting this object to output(1) indicates that
shutdown requests should cause only the output of the
UPS to turn off. Setting this object to system(2)
indicates that shutdown requests will cause the entire
UPS system to turn off."
::= { upsControl 1 }
upsShutdownAfterDelay OBJECT-TYPE
SYNTAX INTEGER -- UNITS seconds
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting this object will shutdown (i.e., turn off)
either the UPS output or the UPS system (as determined
by the value of upsShutdownType at the time of
shutdown) after the indicated number of seconds, or
less if the UPS batteries become depleted. Setting
this object to 0 will cause the shutdown to occur
immediately. Setting this object to -1 will abort the
countdown. If the system is already in the desired
state at the time the countdown reaches 0, then
nothing will happen. That is, there is no additional
action at that time if upsShutdownType = system and
the system is already off. Similarly, there is no
additional action at that time if upsShutdownType =
output and the output is already off. When read,
upsShutdownAfterDelay will return the number of
seconds remaining until shutdown, or -1 if no shutdown
countdown is in effect. On some systems, if the agent
is restarted while a shutdown countdown is in effect,
the countdown may be aborted. Sets to this object
override any upsShutdownAfterDelay already in effect."
::= { upsControl 2 }
upsStartupAfterDelay OBJECT-TYPE
SYNTAX INTEGER -- UNITS seconds
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting this object will start the output after the
indicated number of seconds, including starting the
UPS, if necessary. Setting this object to 0 will
cause the startup to occur immediately. Setting this
object to -1 will abort the countdown. If the output
is already on at the time the countdown reaches 0,
then nothing will happen. Sets to this object
override the effect of any upsStartupAfterDelay
countdown or upsRebootWithDuration countdown in
progress. When read, upsStartupAfterDelay will return
the number of seconds until startup, or -1 if no
startup countdown is in effect. If the countdown
expires during a utility failure, the startup shall
not occur until the utility power is restored. On
some systems, if the agent is restarted while a
startup countdown is in effect, the countdown is
aborted."
::= { upsControl 3 }
upsRebootWithDuration OBJECT-TYPE
SYNTAX INTEGER -- UNITS seconds
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting this object will immediately shutdown (i.e.,
turn off) either the UPS output or the UPS system (as
determined by the value of upsShutdownType at the time
of shutdown) for a period equal to the indicated
number of seconds, after which time the output will be
started, including starting the UPS, if necessary. If
the number of seconds required to perform the request
is greater than the requested duration, then the
requested shutdown and startup cycle shall be
performed in the minimum time possible, but in no case
shall this require more than the requested duration
plus 60 seconds. When read, upsRebootWithDuration
shall return the number of seconds remaining in the
countdown, or -1 if no countdown is in progress. If
the startup should occur during a utility failure, the
startup shall not occur until the utility power is
restored."
::= { upsControl 4 }
upsAutoRestart OBJECT-TYPE
SYNTAX INTEGER
{
on(1),
off(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Setting this object to 'on' will cause the UPS system
to restart after a shutdown if the shutdown occurred
during a power loss as a result of either a
upsShutdownAfterDelay or an internal battery depleted
condition. Setting this object to 'off' will prevent
the UPS system from restarting after a shutdown until
an operator manually or remotely explicitly restarts
it. If the UPS is in a startup or reboot countdown,
then the UPS will not restart until that delay has
been satisfied."
::= { upsControl 5 }
upsConfig OBJECT IDENTIFIER ::= { MitsubishiUPS 9 }
upsConfigInputVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS RMS Volts
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The magnitude of the nominal input voltage (RMS Volts).
On those systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not supported, the request must be
rejected and the agent shall respond with an
appropriate error message, i.e., badValue for SNMPv1,
or inconsistentValue for SNMPv2."
::= { upsConfig 1 }
upsConfigInputFreq OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Hertz
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The nominal input frequency (0.1 Hertz). On those systems
which support read-write access to this object, if there is
an attempt to set this variable to a value that is not
supported, the request must be rejected and the agent
shall respond with an appropriate error message, i.e.,
badValue for SNMPv1, or inconsistentValue for SNMPv2."
::= { upsConfig 2 }
upsConfigOutputVoltage OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS RMS Volts
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The magnitude of the nominal output voltage (RMS Volts).
On those systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not supported, the request must be
rejected and the agent shall respond with an
appropriate error message, i.e., badValue for SNMPv1,
or inconsistentValue for SNMPv2."
::= { upsConfig 3 }
upsConfigOutputFreq OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS 0.1 Hertz
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The nominal output frequency (0.1 Hertz). On those systems
which support read-write access to this object, if there is
an attempt to set this variable to a value that is not
supported, the request must be rejected and the agent
shall respond with an appropriate error message, i.e.,
badValue for SNMPv1, or inconsistentValue for SNMPv2."
::= { upsConfig 4 }
upsConfigOutputVA OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS Volt-Amps
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the nominal Volt-Amp rating (Volt-Amps)."
::= { upsConfig 5 }
upsConfigOutputPower OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS Watts
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The magnitude of the nominal true power rating (watts)."
::= { upsConfig 6 }
upsConfigLowBattTime OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS minutes
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The value of upsEstimatedMinutesRemaining at which a
lowBattery condition is declared. For agents which
support only discrete (discontinuous) values, then the
agent shall round up to the next supported value. If
the requested value is larger than the largest
supported value, then the largest supported value
shall be selected."
::= { upsConfig 7 }
upsConfigAudibleStatus OBJECT-TYPE
SYNTAX INTEGER
{
disabled(1),
enabled(2),
muted(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The requested state of the audible alarm. When in
the disabled state, the audible alarm should never
sound. The enabled state is self-describing. Setting
this object to muted(3) when the audible alarm is
sounding shall temporarily silence the alarm. It will
remain muted until it would normally stop sounding and
the value returned for read operations during this
period shall equal muted(3). At the end of this
period, the value shall revert to enabled(2). Writes
of the value muted(3) when the audible alarm is not
sounding shall be accepted but otherwise shall have no
effect."
::= { upsConfig 8 }
upsConfigLowVoltageTransferPoint OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS RMS Volts
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The minimum input line voltage (RMS Volts) allowed before
the UPS system transfers to battery backup."
::= { upsConfig 9 }
upsConfigHighVoltageTransferPoint OBJECT-TYPE
SYNTAX NonNegativeInteger -- UNITS RMS Volts
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum line voltage (RMS Volts) allowed before the UPS
system transfers to battery backup."
::= { upsConfig 10 }
-- UPS trap information group
upsTrapInfo OBJECT IDENTIFIER ::= { MitsubishiUPS 10 }
trapCode OBJECT-TYPE
SYNTAX Unsigned32
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A number identifying the event for that last trap that was sent."
::= { upsTrapInfo 1 }
trapDescription OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..63))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A string identifying the event for that last trap that was sent."
::= { upsTrapInfo 2 }
-- UPS Traps
-- upsTraps OBJECT IDENTIFIER ::= { Tag 101 }
alarmCritical TRAP-TYPE
ENTERPRISE MitsubishiUPS
VARIABLES { trapCode, trapDescription }
DESCRIPTION
"Critical alarm."
::= 1
alarmWarning TRAP-TYPE
ENTERPRISE MitsubishiUPS
VARIABLES { trapCode, trapDescription }
DESCRIPTION
"Warning alarm."
::= 2
alarmInformation TRAP-TYPE
ENTERPRISE MitsubishiUPS
VARIABLES { trapCode, trapDescription }
DESCRIPTION
"Information alarm."
::= 3
upsAlarmCleared TRAP-TYPE
ENTERPRISE MitsubishiUPS
VARIABLES { trapCode, trapDescription }
DESCRIPTION
"Alarm cleared."
::= 4
upsTrapInitialization TRAP-TYPE
ENTERPRISE MitsubishiUPS
VARIABLES { upsIdentName }
DESCRIPTION
"This trap is sent each time a NetCom device is initialized."
::= 5
END