mibs/MIBS/arris/DOCS-SUBMGT-MIB

792 lines
29 KiB
Plaintext
Raw Permalink Normal View History

2023-12-05 12:25:34 +01:00
DOCS-SUBMGT-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Integer32,
experimental
-- BITS
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
RowStatus,
TruthValue
FROM SNMPv2-TC
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF
docsIfCmtsCmStatusIndex,
docsIfCmtsCmStatusEntry
FROM DOCS-IF-MIB; -- RFC2670
docsSubMgt MODULE-IDENTITY
LAST-UPDATED "0007120000Z" -- July 12, 2000
ORGANIZATION "IETF IPCDN Working Group"
CONTACT-INFO
" Wilson Sawyer
Postal: Arris Interactive
6 Riverside Drive
Andover, MA 01810
U.S.A.
Phone: +1 978 946 4711
E-mail: wsawyer@ieee.org"
DESCRIPTION
"This is the CMTS centric subscriber management MIB for
DOCSIS compliant CMTS. This will be rooted in experimental
space with a future transition to be incorporated into the
cable device MIB."
-- temporary: the following to be assigned by RFC editor. For now,
-- use original experimental docsDev value: { docsDev 4 }
::= { experimental 83 4 }
docsSubMgtObjects OBJECT IDENTIFIER ::= { docsSubMgt 1 }
IpV4orV6Addr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An IP V4 or V6 address expressed as an octet string. The
zero length string is equal to both 0.0.0.0 and the IPv6 :0
address."
SYNTAX OCTET STRING (SIZE (0 | 4 | 16))
docsSubMgtCpeControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsSubMgtCpeControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the docsIfCmtsCmStatusTable and adds 4
objects which reflect the state of subscriber management on a
particular CM."
::= { docsSubMgtObjects 1 }
docsSubMgtCpeControlEntry OBJECT-TYPE
SYNTAX DocsSubMgtCpeControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the docsSubMgtCpeControlTable. All the values
are either set from the system default, or are set from objects
included in the DOCSIS registration request sent upstream to
the CMTS from the CM."
AUGMENTS { docsIfCmtsCmStatusEntry }
::= {docsSubMgtCpeControlTable 1 }
DocsSubMgtCpeControlEntry ::= SEQUENCE
{
docsSubMgtCpeControlMaxCpeIp Integer32,
docsSubMgtCpeControlActive TruthValue,
docsSubMgtCpeControlLearnable TruthValue,
docsSubMgtCpeControlReset TruthValue
}
docsSubMgtCpeControlMaxCpeIp OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of simultaneous IP addresses permitted behind
the CM. If this is set to zero, all CPE traffic from the CM is
dropped. If the provisioning object corresponding to
docsSubMgtCpeIpTable includes more CPE IP address entries for
this modem than the value of this object, then this object is
set to the count of the number of rows in docsSubMgtCpeIpTable
that have the same docsIfCmtsCmStatusIndex value. (E.g. if the
CM has 5 IP addresses specified for it, this value is 5). This
limit applies to learned and docsis-provisioned entries, but
does not limit entries added through some administrative
process at the CMTS. If not set through DOCSIS provisioning,
this object defaults to docsSubMgtCpeMaxIpDefault. Note that
this object is only meaningful if docsSubMgtCpeControlActive
is true."
::= { docsSubMgtCpeControlEntry 1 }
docsSubMgtCpeControlActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this is set to true, CMTS based CPE control is active and
all the actions required by the various filter tables and
controls apply at the CMTS. If this is set to false, no
subscriber management filtering is done at the CMTS (but other
filters may apply). If not set through DOCSIS provisioning,
this object defaults to docsSubMgtCpeActiveDefault."
::= { docsSubMgtCpeControlEntry 2 }
docsSubMgtCpeControlLearnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this is set to true, the CMTS may learn up to
docsSubMgtMaxCpeIp addresses (less any DOCSIS-provisioned
entries) related to this CM. Those IP addresses are added (by
internal process) to the docsSubMgtCpeIpTable. The nature of the
learning mechanism is not specified here. If not set through
DOCSIS provisioning, this object defaults to
docsSubMgtCpeLearnableDefault. Note that this object is only
meaningful if docsSubMgtCpeControlActive is true."
::= { docsSubMgtCpeControlEntry 3 }
docsSubMgtCpeControlReset OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object always returns false on read. If this object is
set to true, the rows with 'learned' addresses in
docsSubMgtCpeIpTable for this CM are deleted from that table."
::= { docsSubMgtCpeControlEntry 4 }
docsSubMgtCpeMaxIpDefault OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value for docsSubMgtCpeControlMaxCpeIp if not
signaled in the DOCSIS Registration request. Upon initial CMTS
initialization, this defaults to 16."
::= { docsSubMgtObjects 2 }
docsSubMgtCpeActiveDefault OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value for docsSubMgtCpeControlActive if not
signaled in the DOCSIS Registration request. Upon initial CMTS
initialization, this defaults to false."
::= { docsSubMgtObjects 3 }
docsSubMgtCpeLearnableDefault OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value for docsSubMgtCpeControlLearnable if not
signaled in the DOCSIS Registration request. Upon initial CMTS
initialization, this defaults to true."
::= { docsSubMgtObjects 4 }
docsSubMgtCpeIpTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsSubMgtCpeIpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of CPE IP addresses known on a per CM basis."
::= { docsSubMgtObjects 5 }
docsSubMgtCpeIpEntry OBJECT-TYPE
SYNTAX DocsSubMgtCpeIpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the docsSubMgtCpeIpTable. The first index is
the specific modem we're referring to, the second index is the
specific CPE IP entry."
INDEX { docsIfCmtsCmStatusIndex,
docsSubMgtCpeIpIndex }
::= {docsSubMgtCpeIpTable 1 }
DocsSubMgtCpeIpEntry ::= SEQUENCE
{
docsSubMgtCpeIpIndex Integer32,
docsSubMgtCpeIpAddr IpV4orV6Addr,
docsSubMgtCpeIpLearned TruthValue
}
docsSubMgtCpeIpIndex OBJECT-TYPE
SYNTAX Integer32(1..1024)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this CPE IP address relative to the indexed CM.
An entry is created either through the included CPE IP addresses
in the provisioning object, or via learning. If a CMTS receives
an IP packet from a CM that contains a source IP address which
does not match one of the docsSubMgtCpeIpAddr entries for this
CM, one of two things occurs. If the number of entries is less
than docsSubMgtCpeControlMaxCpeIp, the source address is added to
the table and the packet is forwarded. If the number of entries
equals the docsSubMgtCpeControlMaxCpeIp, AND
docsSubMgtCpeControlActive is true, then the packet is dropped.
Otherwise the packet is forwarded. "
::= { docsSubMgtCpeIpEntry 1 }
docsSubMgtCpeIpAddr OBJECT-TYPE
SYNTAX IpV4orV6Addr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address either set from provisioning or learned via
wiretapping. See docsSubMgtCpeIpIndex for the mechanism."
::= { docsSubMgtCpeIpEntry 2 }
docsSubMgtCpeIpLearned OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, this entry was learned from IP packets sent
upstream rather than from the provisioning objects."
::= { docsSubMgtCpeIpEntry 3 }
-- The generic packet filter table. Note that this just defines the
-- match criteria. The docsSubMgtCmFilterTable links this table to
-- the specific modems.
docsSubMgtPktFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsSubMgtPktFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of filter or classifier criteria. Classifiers are
assigned by group to the individual CMs. That assignment is made
via the configuration objects sent upstream from the CM to the
CMTS during registration."
::= { docsSubMgtObjects 6 }
docsSubMgtPktFilterEntry OBJECT-TYPE
SYNTAX DocsSubMgtPktFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the docsSubMgtPktFilterTable."
INDEX { docsSubMgtPktFilterGroup,
docsSubMgtPktFilterIndex }
::= {docsSubMgtPktFilterTable 1 }
DocsSubMgtPktFilterEntry ::= SEQUENCE
{
docsSubMgtPktFilterGroup Integer32,
docsSubMgtPktFilterIndex Integer32,
docsSubMgtPktFilterSrcAddr IpV4orV6Addr,
docsSubMgtPktFilterSrcMask IpV4orV6Addr,
docsSubMgtPktFilterDstAddr IpV4orV6Addr,
docsSubMgtPktFilterDstMask IpV4orV6Addr,
docsSubMgtPktFilterUlp Integer32,
docsSubMgtPktFilterTosValue OCTET STRING,
docsSubMgtPktFilterTosMask OCTET STRING,
docsSubMgtPktFilterAction INTEGER,
docsSubMgtPktFilterMatches Counter32,
docsSubMgtPktFilterStatus RowStatus
}
docsSubMgtPktFilterGroup OBJECT-TYPE
SYNTAX Integer32(1..1024)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies an ordered group of filters. Each modem may be
associated with a filter group for its upstream traffic
(docsSubMgtCmFilterUpstream) and a filter group for its
downstream traffic (docsSubMgtCmFilterDownstream). Typically,
many modems will use the same filter group."
::= { docsSubMgtPktFilterEntry 1 }
docsSubMgtPktFilterIndex OBJECT-TYPE
SYNTAX Integer32(1..1024)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index which describes the ordering of a set of filter
specifications within the group. Filters are applied in index
order."
::= { docsSubMgtPktFilterEntry 2 }
docsSubMgtPktFilterSrcAddr OBJECT-TYPE
SYNTAX IpV4orV6Addr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source IP address to match in the packet to be
classified. By default, this is the all-zero's IP v4 and v6
address. A packet matches the SrcAddr filter if the following is
true:
AND (FilterSrcAddr, FilterSrcMask) ==
AND (Packet SrcAddr, FilterSrcMask).
The mask value is applied to both the match value in this table
and to the packet IP address."
DEFVAL { ''h }
::= { docsSubMgtPktFilterEntry 3 }
docsSubMgtPktFilterSrcMask OBJECT-TYPE
SYNTAX IpV4orV6Addr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A bit mask that is to be applied to the source address
prior to matching. This, taken with the SrcAddr specifies a
matching criteria. By default, the pair specifies a filter
which matches all source addresses. This mask is not
necessarily the same as a subnet mask, but for IPv4 addresses
the 1's bits must be leftmost and contiguous. IPv6 masks have
no such restriction."
DEFVAL { ''h }
::= { docsSubMgtPktFilterEntry 4 }
docsSubMgtPktFilterDstAddr OBJECT-TYPE
SYNTAX IpV4orV6Addr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination IP address to match in the packet to be
classified. By default, this is the all-zero's IP v4 and v6
address. A packet matches the DstAddr filter if the following is
true:
AND (FilterDstAddr, FilterDstMask) ==
AND (Packet DstAddr, FilterDstMask).
The mask value is applied to both the match value in this table
and to the packet IP address."
DEFVAL { ''h }
::= { docsSubMgtPktFilterEntry 5 }
docsSubMgtPktFilterDstMask OBJECT-TYPE
SYNTAX IpV4orV6Addr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A bit mask that is to be applied to the destination
address prior to matching. This, taken with the DstAddr
specifies a matching criteria. By default, the pair specifies
a filter which matches all destination addresses. This mask is
not necessarily the same as a subnet mask, but for IPv4
addresses the 1's bits must be leftmost and contiguous. IPv6
masks have no such restriction."
DEFVAL { ''h }
::= { docsSubMgtPktFilterEntry 6 }
docsSubMgtPktFilterUlp OBJECT-TYPE
SYNTAX Integer32 (0..256)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Upper level protocol to match. If this value is 256,
matches ALL ULP values. Otherwise, this matches the specific
protocol value. Note that if the packet ULP is either 6 (tcp) or
17 (udp), then docsSubMgtPktTcpUdpFilterTable must also be
consulted (if its entry exists) to see if this entry matches.
Obviously, if this value is neither tcp, udp nor 256, then that
table need not be matched against."
DEFVAL { 256 }
::= { docsSubMgtPktFilterEntry 7 }
docsSubMgtPktFilterTosValue OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The TOS value to match in the IP packet."
DEFVAL { '0'h }
::= { docsSubMgtPktFilterEntry 8 }
docsSubMgtPktFilterTosMask OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(1))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mask to apply against the TOS value to be matched in the
IP packet. The default for both these objects taken together
matches all TOS values. A packet matches this filter if the
following is true:
AND (FilterTosValue, FilterTosMask) ==
AND (Packet TOS Value, FilterTosMask)."
DEFVAL { '0'h }
::= { docsSubMgtPktFilterEntry 9 }
docsSubMgtPktFilterAction OBJECT-TYPE
SYNTAX INTEGER
{
accept(1),
drop(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The action to take upon this filter matching. Accept means
to accept the packet for further processing. Drop means to drop
the packet."
DEFVAL { accept }
::= { docsSubMgtPktFilterEntry 10 }
docsSubMgtPktFilterMatches OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times this specific rule
has been matched. This is incremented any time this rule is
encountered and all components match. It is only incremented for
the first (lowest-indexed) filter matching a packet."
::= { docsSubMgtPktFilterEntry 11 }
docsSubMgtPktFilterStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Standard rowStatus object for creating this row. Any object
in this row which is writable may be changed at any time while
the row is active."
::= { docsSubMgtPktFilterEntry 12 }
docsSubMgtTcpUdpFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsSubMgtTcpUdpFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is an adjunct to docsSubMgtPktFilterTable. It provides
optional filtering based on elements in TCP or UDP headers.
This table is separate from docsSubMgtPktFilterTable only
because it is expected to be used more rarely. This table
is not consulted unless the upper-layer protocol is TCP,
UDP, or 'any'."
::= { docsSubMgtObjects 7 }
docsSubMgtTcpUdpFilterEntry OBJECT-TYPE
SYNTAX DocsSubMgtTcpUdpFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines filtering criteria for TCP and UDP headers."
INDEX { docsSubMgtPktFilterGroup, docsSubMgtPktFilterIndex }
::= {docsSubMgtTcpUdpFilterTable 1 }
DocsSubMgtTcpUdpFilterEntry ::= SEQUENCE
{
docsSubMgtTcpUdpSrcPort Integer32,
docsSubMgtTcpUdpDstPort Integer32,
docsSubMgtTcpFlagValues BITS,
docsSubMgtTcpFlagMask BITS,
docsSubMgtTcpUdpStatus RowStatus
}
docsSubMgtTcpUdpSrcPort OBJECT-TYPE
SYNTAX Integer32(0..65536)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source port to match. 65536 matches any value in the
TCP or UDP source port field."
DEFVAL { 65536 }
::= { docsSubMgtTcpUdpFilterEntry 1 }
docsSubMgtTcpUdpDstPort OBJECT-TYPE
SYNTAX Integer32(0..65536)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination port to match. 65536 matches any value in
the TCP or UDP destination port field."
DEFVAL { 65536 }
::= { docsSubMgtTcpUdpFilterEntry 2 }
docsSubMgtTcpFlagValues OBJECT-TYPE
SYNTAX BITS
{
urgent(0),
ack(1),
push(2),
reset(3),
syn(4),
fin(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the flags of interest. The value of this
object MUST always be a subset (proper or otherwise) of
docsSubMgtTcpFlagMask. An attempt to violate this constraint
returns an inconsistentValue error for an SNMPv2 or v3 agent
and a badValue error for an SNMPv1 agent."
DEFVAL { {} }
::= { docsSubMgtTcpUdpFilterEntry 3 }
docsSubMgtTcpFlagMask OBJECT-TYPE
SYNTAX BITS
{
urgent(0),
ack(1),
push(2),
reset(3),
syn(4),
fin(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bit set indicates the flags of interest in the TCP
header for the packet to be matched. For example to match all
packets where the urgent bit is set, but that are not either syn
or fin, the value of docsSubMgtTcpFlagValues would be { urgent },
and the value of this object would be { urgent, syn, fin }"
DEFVAL { {} }
::= { docsSubMgtTcpUdpFilterEntry 4 }
docsSubMgtTcpUdpStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Standard row object for this table. Any object in the
conceptual row may be modified regardless of whether this row is
active or not."
::= { docsSubMgtTcpUdpFilterEntry 5 }
docsSubMgtCmFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsSubMgtCmFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Binds filter groups to modems. This table identifies for
each modem the upstream and downstream filter groups that apply
to packets for that modem. Zero is used as a distinguished value
to mean no filter group."
::= { docsSubMgtObjects 8 }
docsSubMgtCmFilterEntry OBJECT-TYPE
SYNTAX DocsSubMgtCmFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Binds a filter group to each direction of traffic for a
modem."
AUGMENTS { docsIfCmtsCmStatusEntry }
::= {docsSubMgtCmFilterTable 1 }
DocsSubMgtCmFilterEntry ::= SEQUENCE
{
docsSubMgtSubFilterDownstream Integer32,
docsSubMgtSubFilterUpstream Integer32,
docsSubMgtCmFilterDownstream Integer32,
docsSubMgtCmFilterUpstream Integer32
}
docsSubMgtSubFilterDownstream OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The filter group applied to traffic destined for subscribers
attached to the referenced CM. This is set upon row creation to
either the default (docsSubMgtSubFilterDownDefault), or to the
value in the provisioning object sent upstream from the CM to the
CMTS during registration. The value of this object is a pointer
into the docsSubMgtPktFilterTable and refers to all filter rows
with matching docsSubMgtPktFilterGroup indices. If there are no
matching filter rows in that table, or if this object is set to
zero, no filtering is applied to traffic destined to hosts
attached to this CM."
::= { docsSubMgtCmFilterEntry 1 }
docsSubMgtSubFilterUpstream OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The filter group applied to traffic originating from
subscribers attached to the referenced CM. This is set upon row
creation to either the default (docsSubMgtSubFilterUpDefault), or
to the value in the provisioning object sent upstream from the CM
to the CMTS. The value of this object is a pointer into the
docsSubMgtPktFilterTable and refers to all filter rows with
matching docsSubMgtPktFilterGroup indices. If there are no
matching filter rows in that table, or if this object is set to
zero, no filtering is applied to traffic originating from
hosts attached to this CM."
::= { docsSubMgtCmFilterEntry 2 }
docsSubMgtCmFilterDownstream OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The filter group applied to traffic destined for the
referenced CM itself. This is set upon row creation to either
the default (docsSubMgtCmFilterDownDefault), or to the value in
the provisioning object sent upstream from the CM to the CMTS
during registration. The value of this object is a pointer into
the docsSubMgtPktFilterTable and refers to all filter rows with
matching docsSubMgtPktFilterGroup indices. If there are no
matching filter rows in that table, or if this object is set to
zero, no filtering is applied to traffic destined to this CM."
::= { docsSubMgtCmFilterEntry 3 }
docsSubMgtCmFilterUpstream OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The filter group applied to traffic originating from the
referenced CM itself. This is set upon row creation to either
the default (docsSubMgtCmFilterUpDefault), or to the value in
the provisioning object sent upstream from the CM to the CMTS.
The value of this object is a pointer into the
docsSubMgtPktFilterTable and refers to all filter rows with
matching docsSubMgtPktFilterGroup indices. If there are no
matching filter rows in that table, or if this object is set
to zero, no filtering is applied to traffic originating from
this CM."
::= { docsSubMgtCmFilterEntry 4 }
docsSubMgtSubFilterDownDefault OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Upon a row creation in docsSubMgtCmFilterTable,
docsSubMgtSubFilterDownstream is set to this value if no
provisioning object is present to override it. This object is
persistent across CMTS reboots. Upon initial CMTS
initialization, this defaults to 0."
::= { docsSubMgtObjects 9 }
docsSubMgtSubFilterUpDefault OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Upon a row creation in docsSubMgtCmFilterTable,
docsSubMgtSubFilterUpstream is set to this value if no
provisioning object is present to override it. This object is
persistent across CMTS reboots. Upon initial CMTS
initialization, this defaults to 0."
::= { docsSubMgtObjects 10 }
docsSubMgtCmFilterDownDefault OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Upon a row creation in docsSubMgtCmFilterTable,
docsSubMgtCmFilterDownstream is set to this value if no
provisioning object is present to override it. This object is
persistent across CMTS reboots. Upon initial CMTS
initialization, this defaults to 0."
::= { docsSubMgtObjects 11 }
docsSubMgtCmFilterUpDefault OBJECT-TYPE
SYNTAX Integer32(0..1024)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Upon a row creation in docsSubMgtCmFilterTable,
docsSubMgtCmFilterUpstream is set to this value if no
provisioning object is present to override it. This object is
persistent across CMTS reboots. Upon initial CMTS
initialization, this defaults to 0."
::= { docsSubMgtObjects 12 }
docsSubMgtNotification OBJECT IDENTIFIER ::= { docsSubMgt 2 }
docsSubMgtConformance OBJECT IDENTIFIER ::= { docsSubMgt 3 }
docsSubMgtCompliances OBJECT IDENTIFIER ::=
{ docsSubMgtConformance 1 }
docsSubMgtGroups OBJECT IDENTIFIER ::=
{ docsSubMgtConformance 2 }
docsSubMgtBasicCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for CMTS devices that implement
CMTS centric subscriber management."
MODULE
MANDATORY-GROUPS {
docsSubMgtGroup
}
::= { docsSubMgtCompliances 1 }
docsSubMgtGroup OBJECT-GROUP
OBJECTS {
docsSubMgtCpeControlMaxCpeIp,
docsSubMgtCpeControlActive,
docsSubMgtCpeControlLearnable,
docsSubMgtCpeControlReset,
docsSubMgtCpeMaxIpDefault,
docsSubMgtCpeActiveDefault,
docsSubMgtCpeLearnableDefault,
docsSubMgtCpeIpAddr,
docsSubMgtCpeIpLearned,
docsSubMgtPktFilterSrcAddr,
docsSubMgtPktFilterSrcMask,
docsSubMgtPktFilterDstAddr,
docsSubMgtPktFilterDstMask,
docsSubMgtPktFilterUlp,
docsSubMgtPktFilterTosValue,
docsSubMgtPktFilterTosMask,
docsSubMgtPktFilterAction,
docsSubMgtPktFilterMatches,
docsSubMgtPktFilterStatus,
docsSubMgtTcpUdpSrcPort,
docsSubMgtTcpUdpDstPort,
docsSubMgtTcpFlagValues,
docsSubMgtTcpFlagMask,
docsSubMgtTcpUdpStatus,
docsSubMgtSubFilterDownstream,
docsSubMgtSubFilterUpstream,
docsSubMgtCmFilterDownstream,
docsSubMgtCmFilterUpstream,
docsSubMgtSubFilterDownDefault,
docsSubMgtSubFilterUpDefault,
docsSubMgtCmFilterDownDefault,
docsSubMgtCmFilterUpDefault
}
STATUS current
DESCRIPTION
"The objects use to managed host-based cable modems
via a set of CMTS enforced controls."
::= { docsSubMgtGroups 1 }
END