david/mibs
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
main
mibs/MIBS/cisco/CISCOSB-TIMESYNCHRONIZATION-MIB

1939 lines
72 KiB
Plaintext
Raw Permalink Normal View History

Initial commit
2023-12-05 12:25:34 +01:00
CISCOSB-TIMESYNCHRONIZATION-MIB DEFINITIONS ::= BEGIN
IMPORTS
switch001 FROM CISCOSB-MIB
Unsigned32, Integer32, IpAddress,
MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI
InetAddressType, InetAddress FROM INET-ADDRESS-MIB
DisplayString, TEXTUAL-CONVENTION ,
RowStatus, TruthValue FROM SNMPv2-TC
InterfaceIndex FROM IF-MIB;
rlTimeSynchronization MODULE-IDENTITY
LAST-UPDATED "202105170000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
"Postal: 170 West Tasman Drive
San Jose , CA 95134-1706
USA
Website: Cisco Small Business Support Community <http://www.cisco.com/go/smallbizsupport>"
DESCRIPTION
"The MIB module describes the private MIB for SNTP & TIME definitions."
REVISION "200906180024Z"
DESCRIPTION
"Added support in DHCP timezone option."
REVISION "200709060024Z"
DESCRIPTION
"Added rlClockStatus"
REVISION "200311230024Z"
DESCRIPTION
"Initial revision"
::= { switch001 92 }
rlTimeSyncMethodMode OBJECT IDENTIFIER ::= { rlTimeSynchronization 1 }
rlSntpNtpClient OBJECT IDENTIFIER ::= { rlTimeSynchronization 2 }
rlSntpNtpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 1 }
rlSntpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 2 }
rlNtpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 3 }
--
-- Textual Conventions
--
NTPTimeStamp ::= TEXTUAL-CONVENTION
DISPLAY-HINT "4d.4d"
STATUS current
DESCRIPTION "NTP timestamps are represented as a 64-bit
unsigned fixed-point number, in seconds relative to
00:00 on 1 January 1900. The integer part is in the
first 32 bits and the fraction part is in the last
32 bits."
REFERENCE "D.L. Mills, 'Network Time Protocol (Version 3)',
RFC-1305, March 1992, Section 3.1"
SYNTAX OCTET STRING (SIZE (8))
NTPSignedTimeValue ::= TEXTUAL-CONVENTION
DISPLAY-HINT "2d.2d"
STATUS current
DESCRIPTION "The time in seconds that could represent signed
quantities like time delay with respect to some
source. This textual-convention is specific to CISCOSB
implementation of NTP where 32-bit integers are used
for such quantities. The signed integer part is in
the first 16 bits and the fraction part is in the
last 16 bits."
SYNTAX OCTET STRING (SIZE (4))
NTPStratum ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the stratum of the clock. The stratum
defines the accuracy of a time server. Higher the
stratum, lower the accuracy.
0, unspecified
1, primary reference (e.g., calibrated atomic clock,
radio clock)
2-255, secondary reference (via NTP)"
REFERENCE "D.L. Mills, 'Network Time Protocol (Version 3)',
RFC-1305, March 1992, Section 2.2"
SYNTAX Integer32 (0..255)
-- ----------------------------------------------------------------------
-- Global TimeSyncMethod
-- ----------------------------------------------------------------------
RlTimeSyncMethod ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Method to be used for time synchronization in the device."
SYNTAX INTEGER { none(1),
sntp(2),
ntp(3)
}
RlDaylightSavingTimeMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Daylight Saving Time - Recurring/Date/None."
SYNTAX INTEGER {
recurring(1),
date(2),
none(3)
}
rlTimeSyncMibVersion OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "TimeSync Mib Version."
::= { rlTimeSyncMethodMode 1 }
rndTimeSyncManagedTime OBJECT-TYPE
SYNTAX DisplayString (SIZE(6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The time will be sent in the format hhmmss"
::= { rlTimeSyncMethodMode 2 }
rndTimeSyncManagedDate OBJECT-TYPE
SYNTAX DisplayString (SIZE(6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The date will be sent in the format ddmmyy"
::= { rlTimeSyncMethodMode 3 }
rndTimeSyncManagedDateTime OBJECT-TYPE
SYNTAX DisplayString (SIZE(12))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The date and time will be sent in the format ddmmyyhhmmss"
::= { rlTimeSyncMethodMode 4 }
rlTimeSyncMethod OBJECT-TYPE
SYNTAX RlTimeSyncMethod
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Method to be used for time synchronization in the device."
DEFVAL { none }
::= { rlTimeSyncMethodMode 5 }
rlTimeZone OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Offset from Greenwich time (format [+/-]hh:mm)."
::= {rlTimeSyncMethodMode 6 }
rlTimeZoneCode OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Code definition for current TimeZone."
::= {rlTimeSyncMethodMode 7 }
rlDaylightSavingTimeMode OBJECT-TYPE
SYNTAX RlDaylightSavingTimeMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time - Recurring/Date/None."
DEFVAL { none }
::= { rlTimeSyncMethodMode 8 }
rlDaylightSavingTimeStart OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time start date.
In recurring mode (format 1): week wday month hh:mm
In recurring mode (format 2): RJul n hh:mm
In date mode: month day year hh:mm
week: 0-6 (0=First, 6=Last)
wday: 1-7 (Sunday-Saturday)
month: 1-12 (January-December)
day: 1-31
year: 0-99 (2000-2099)
hh: 0-23 (hours)
mm: 0-59 (minutes)
n: 0-365 (zero-based Julian day of the year. Leap days shall be
counted, and it is possible to refer to February 29).
Format 2 for recurring mode is used only in the dynamic entry and
should not be used in the static entry (with index 1)."
::= { rlTimeSyncMethodMode 9 }
rlDaylightSavingTimeEnd OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time start date.
In recurring mode (format 1): week wday month hh:mm
In recurring mode (format 2): RJul n hh:mm
In date mode: month day year hh:mm
week: 0-6 (0=First, 6=Last)
wday: 1-7 (Sunday-Saturday)
month: 1-12 (January-December)
day: 1-31
year: 0-99 (2000-2099)
hh: 0-23 (hours)
mm: 0-59 (minutes)
n: 0-365 (zero-based Julian day of the year. Leap days shall be
counted, and it is possible to refer to February 29).
Format 2 for recurring mode is used only in the dynamic entry and
should not be used in the static entry (with index 1)."
::= { rlTimeSyncMethodMode 10 }
rlDaylightSavingTimeOffset OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time - The number of minutes to add to
the clock during summer time."
DEFVAL { 60 }
::= { rlTimeSyncMethodMode 11 }
rlDaylightSavingTimeCode OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Code definition for current Daylight Saving Time."
::= {rlTimeSyncMethodMode 12 }
rlTZDSTOffset OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Local Time Zone and Daylight Saving Time offset
in seconds."
::= { rlTimeSyncMethodMode 13 }
rlTimeZoneName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Human readable string describing Local Time Zone and Daylight Saving Time."
::= {rlTimeSyncMethodMode 14 }
--
-- TimeZone table
--
-- TimeZone table aimed to replace next mibs:
-- rlTimeSyncMethod
-- rlTimeZone
-- rlTimeZoneCode
-- rlDaylightSavingTimeMode
-- rlDaylightSavingTimeStart
-- rlDaylightSavingTimeEnd
-- rlDaylightSavingTimeOffset
-- rlDaylightSavingTimeCode
-- rlTZDSTOffset
-- rlTimeZoneName
-- Table consist of one entry (with index = 1) and each field corresponding
-- to one of this MIB scalars, holding Timezone and Summertime static information.
-- In case DHCP timezone option is supported, the table will contain another row,
-- with index = 2, that will contain dynamic values for Timezone and Summertime
-- received through DHCP.
rlTimeZoneTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlTimeZoneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "TimeZone information."
::= { rlTimeSyncMethodMode 15 }
rlTimeZoneEntry OBJECT-TYPE
SYNTAX RlTimeZoneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The row definition for this table."
INDEX { rlTimeZoneIndex }
::= { rlTimeZoneTable 1 }
RlTimeZoneEntry ::= SEQUENCE {
rlTimeZoneIndex INTEGER,
rlTimeZoneTimeSyncMethod RlTimeSyncMethod,
rlTimeZoneTimeZoneOffset DisplayString (SIZE(1..6)),
rlTimeZoneTimeZoneCode DisplayString (SIZE(0..16)),
rlTimeZoneDaylightSavingTimeMode RlDaylightSavingTimeMode,
rlTimeZoneDaylightSavingTimeStart OCTET STRING (SIZE(14)),
rlTimeZoneDaylightSavingTimeEnd OCTET STRING (SIZE(14)),
rlTimeZoneDaylightSavingTimeOffset Integer32,
rlTimeZoneDaylightSavingTimeCode DisplayString (SIZE(0..16)),
rlTimeZoneTZDSTOffset INTEGER,
rlTimeZoneTimeZoneName DisplayString (SIZE(0..16)),
rlTimeZoneDataType INTEGER,
rlTimeZoneDataSourceIfIndex INTEGER,
rlTimeZoneDataDynamicConfSource INTEGER
}
rlTimeZoneIndex OBJECT-TYPE
SYNTAX INTEGER (1..2)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Entry index. A row with index 2 will be existing in case the DHCP
timezone is supported, and will contain Timezone and Summertime dynamic
values.
Using index 2 in SET operations is allowed only for SNMP
inner clients (SNMPServ users), on condition that DHCP timezone option
is supported."
::= { rlTimeZoneEntry 1 }
rlTimeZoneTimeSyncMethod OBJECT-TYPE
SYNTAX RlTimeSyncMethod
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Method to be used for time synchronization in the device."
DEFVAL { none }
::= { rlTimeZoneEntry 2 }
rlTimeZoneTimeZoneOffset OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Offset from Greenwich time (format [+/-]hh:mm)."
::= { rlTimeZoneEntry 3 }
rlTimeZoneTimeZoneCode OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Code definition for current TimeZone."
::= { rlTimeZoneEntry 4 }
rlTimeZoneDaylightSavingTimeMode OBJECT-TYPE
SYNTAX RlDaylightSavingTimeMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time - Recurring/Date/None."
DEFVAL { none }
::= { rlTimeZoneEntry 5 }
rlTimeZoneDaylightSavingTimeStart OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time start date.
In recurring mode (format 1): week wday month hh:mm
In recurring mode (format 2): RJul n hh:mm
In date mode: month day year hh:mm
week: 0-6 (0=First, 6=Last)
wday: 1-7 (Sunday-Saturday)
month: 1-12 (January-December)
day: 1-31
year: 0-99 (2000-2099)
hh: 0-23 (hours)
mm: 0-59 (minutes)
n: 0-365 (zero-based Julian day of the year. Leap days shall be
counted, and it is possible to refer to February 29).
Format 2 for recurring mode is used only in the dynamic entry and
should not be used in the static entry (with index 1)."
::= { rlTimeZoneEntry 6 }
rlTimeZoneDaylightSavingTimeEnd OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time start date.
In recurring mode (format 1): week wday month hh:mm
In recurring mode (format 2): RJul n hh:mm
In date mode: month day year hh:mm
week: 0-6 (0=First, 6=Last)
wday: 1-7 (Sunday-Saturday)
month: 1-12 (January-December)
day: 1-31
year: 0-99 (2000-2099)
hh: 0-23 (hours)
mm: 0-59 (minutes)
n: 0-365 (zero-based Julian day of the year. Leap days shall be
counted, and it is possible to refer to February 29).
Format 2 for recurring mode is used only in the dynamic entry and
should not be used in the static entry (with index 1)."
::= { rlTimeZoneEntry 7 }
rlTimeZoneDaylightSavingTimeOffset OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Daylight Saving Time - The number of minutes to add to
the clock during summer time."
DEFVAL { 60 }
::= { rlTimeZoneEntry 8 }
rlTimeZoneDaylightSavingTimeCode OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Code definition for current Daylight Saving Time."
::= { rlTimeZoneEntry 9 }
rlTimeZoneTZDSTOffset OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Local Time Zone and Daylight Saving Time offset in seconds."
::= { rlTimeZoneEntry 10 }
rlTimeZoneTimeZoneName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Human readable string describing Local Time Zone and Daylight Saving Time."
::= { rlTimeZoneEntry 11 }
rlTimeZoneDataType OBJECT-TYPE
SYNTAX INTEGER {
static(1),
dynamic(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The type of data in this entry: static or dynamic."
DEFVAL { static }
::= { rlTimeZoneEntry 12 }
rlTimeZoneDataSourceIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "IfIndex of the interface through which the dynamic data of this row has been learned.
The value of this field will be 0 if rlTimeZoneTimeDataType is static (since it is
relevant only for dynamic entry), and this is the only value allowed for SET in this case."
DEFVAL { 0 }
::= { rlTimeZoneEntry 13 }
rlTimeZoneDataDynamicConfSource OBJECT-TYPE
SYNTAX INTEGER {
none(1),
dhcpv4(2),
dhcpv6(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The source of dynamic data in this entry, for example: dhcpv4.
Values other than 'none' are relevant only for dynamic entry."
DEFVAL { none }
::= { rlTimeZoneEntry 14 }
rlClockStatus OBJECT-TYPE
SYNTAX INTEGER {
invalid(1),
manuallySet(2),
synchronizedBySntp(3),
setByRtc(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Current status of the clock. The value 'invalid' means time is meaninglesss,
since it has not been manually configured, or achieved as a result
of SNTP synchronization or set by RTC."
::= {rlTimeSyncMethodMode 16 }
rlDhcpTimezoneOptionEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Specifies whether the DHCP Timezone option (DHCPv4 option 100) is supported in the system.
Setting this value to FALSE, will clear Timezone and Summertime dynamic configuration,
so that:
1) rlTimeZoneTimeZoneCode and rlTimeZoneDaylightSavingTimeCode length will
be 0 for rlTimeZoneEntry whose index = 2 (dynamic entry).
2) the operative values of Timezone and Summertime will be those
statically configured. Thus, GET operations on the following
MIB scalars will result is static values:
rlTimeZone, rlTimeZoneCode, rlDaylightSavingTimeMode,
rlDaylightSavingTimeStart, rlDaylightSavingTimeEnd, rlDaylightSavingTimeOffset,
rlDaylightSavingTimeCode, rlTZDSTOffset."
::= {rlTimeSyncMethodMode 17 }
rlAutomaticClockSetFromPCEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Specifies whether automatic set of time and date is permitted from
connected host PC.
The feature is meant to be used in order to initialize the clock
after reboot (if SNTP is not in use), since the device does not have
a realtime clock."
DEFVAL { false }
::= {rlTimeSyncMethodMode 18 }
rlTimeAndDateHaveBeenSet OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates whether the time and date have been set in the
device, manually or through SNTP synchronization.
If only time has been set, the value of this MIB will
be FALSE. If only date has been set, the value of this MIB
will be FALSE."
::= {rlTimeSyncMethodMode 19 }
-- ----------------------------------------------------------------------
-- SNTP/NTP client configuration parameters
-- ----------------------------------------------------------------------
RlSntpNtpSyncType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Method to be used for time synchronization in the device."
SYNTAX INTEGER {
none(1),
unicast(2),
anycast(3),
broadcast(4)
}
RlSntpNtpSyncEntryType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Entry in rlSntpNtpConfigSrvTable."
SYNTAX INTEGER {
primaryPollSrv(1),
syncSrv(2)
}
rlSntpNtpMibVersion OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SntpNtp Mib Version."
::= { rlSntpNtpConfig 1 }
rlSntpNtpConfigMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unicast(2),
anycast(3),
multicast(4),
unicastAnycast(5),
unicastMulticast(6),
anycastMulticast(7),
unicastAnycastMulticast(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Current configuration operational mode of SNTP/NTP client."
DEFVAL { none }
::= { rlSntpNtpConfig 2 }
rlSntpNtpConfigSysStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of the local clock. If the value is set
to 1, i.e., this is a primary reference, then the
Primary-Clock procedure described in Section 3.4.6,
in RFC-1305 is invoked."
::= { rlSntpNtpConfig 3 }
rlSntpNtpConfigPollInterval OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Period of time (in seconds) between succesive attempts to
perform an update via SNTP."
DEFVAL { 1024 }
::= { rlSntpNtpConfig 4 }
rlSntpNtpConfigPrimaryPollSrvAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Ip Address of a trusted SNTP server for polling."
::= { rlSntpNtpConfig 5 }
rlSntpNtpConfigPrimaryPollSrvMrid OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The mrid of the primary server."
::= { rlSntpNtpConfig 6 }
rlSntpNtpConfigPrimaryPollSrvIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The interface addressed of the primary server."
::= { rlSntpNtpConfig 7 }
rlSntpNtpConfigPrimaryPollSrvStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of the primary polling server."
::= { rlSntpNtpConfig 8 }
rlSntpNtpConfigSyncSrvAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Ip Address of the synced server."
::= { rlSntpNtpConfig 9 }
rlSntpNtpConfigSyncSrvMrid OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The mrid of the synced server."
::= { rlSntpNtpConfig 10 }
rlSntpNtpConfigSyncSrvIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The interface addressed of the synced server."
::= { rlSntpNtpConfig 11 }
rlSntpNtpConfigSyncSrvType OBJECT-TYPE
SYNTAX RlSntpNtpSyncType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Synced server type."
DEFVAL { none }
::= { rlSntpNtpConfig 12 }
rlSntpNtpConfigSyncSrvStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of the synced server."
::= { rlSntpNtpConfig 13 }
rlSntpNtpConfigRetryTimeout OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP/NTP requests Retry Interval."
::= { rlSntpNtpConfig 14 }
rlSntpNtpConfigRetryCnt OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP/NTP requests Retry Count."
::= { rlSntpNtpConfig 15 }
-- ----------------------------------------------------------------------
-- SNTP Config Servers
-- ----------------------------------------------------------------------
-- Will replace next MIBs:
-- rlSntpNtpConfigPrimaryPollSrvAddr
-- rlSntpNtpConfigPrimaryPollSrvMrid
-- rlSntpNtpConfigPrimaryPollSrvIfIndex
-- rlSntpNtpConfigPrimaryPollSrvStratum
-- rlSntpNtpConfigSyncSrvAddr
-- rlSntpNtpConfigSyncSrvMrid
-- rlSntpNtpConfigSyncSrvIfIndex
-- rlSntpNtpConfigSyncSrvType
-- rlSntpNtpConfigSyncSrvStratum
rlSntpNtpConfigSrvTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpNtpConfigSrvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing information about config servers."
::= { rlSntpNtpConfig 16 }
rlSntpNtpConfigSrvEntry OBJECT-TYPE
SYNTAX RlSntpNtpConfigSrvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Entry in rlSntpNtpConfigSrvTable."
INDEX { rlSntpNtpConfigSrvEntryType }
::= { rlSntpNtpConfigSrvTable 1 }
RlSntpNtpConfigSrvEntry ::=
SEQUENCE {
rlSntpNtpConfigSrvEntryType RlSntpNtpSyncEntryType,
rlSntpNtpConfigSrvInetAddressType InetAddressType,
rlSntpNtpConfigSrvInetAddress InetAddress,
rlSntpNtpConfigSrvMrid INTEGER,
rlSntpNtpConfigSrvIfIndex INTEGER,
rlSntpNtpConfigSrvSyncType RlSntpNtpSyncType,
rlSntpNtpConfigSrvStratum NTPStratum
}
rlSntpNtpConfigSrvEntryType OBJECT-TYPE
SYNTAX RlSntpNtpSyncEntryType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Server type: Synchronize Server or Primary Poll Server."
::= { rlSntpNtpConfigSrvEntry 1 }
rlSntpNtpConfigSrvInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server inet address type."
::= { rlSntpNtpConfigSrvEntry 2 }
rlSntpNtpConfigSrvInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server inet address."
::= { rlSntpNtpConfigSrvEntry 3 }
rlSntpNtpConfigSrvMrid OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The mrid of the server."
::= { rlSntpNtpConfigSrvEntry 4 }
rlSntpNtpConfigSrvIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The interface addressed of the server."
::= { rlSntpNtpConfigSrvEntry 5 }
rlSntpNtpConfigSrvSyncType OBJECT-TYPE
SYNTAX RlSntpNtpSyncType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The type of synchronization."
::= { rlSntpNtpConfigSrvEntry 6 }
rlSntpNtpConfigSrvStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of the synced server."
::= { rlSntpNtpConfigSrvEntry 7 }
-- ----------------------------------------------------------------------
-- SNTP client configuration parameters
-- ----------------------------------------------------------------------
rlSntpClientMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
active(2),
passive(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Current operational mode of SNTP client."
DEFVAL { none }
::= { rlSntpConfig 1 }
rlSntpUnicastAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Unicast Administrative state - Enable/Disable SNTP.
In case of reinitializing polling or time
synchronization this MIB is modified. The MIB can
be enabled even thought it is already enabled."
DEFVAL { disabled }
::= { rlSntpConfig 2 }
rlSntpBroadcastAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2),
ipv4OnlyEnabled(3),
ipv6OnlyEnabled(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Broadcast Administrative state - Enable/Disable SNTP.
In case of reinitializing polling or time
synchronization this MIB is modified. The MIB can
be enabled even thought it is already enabled."
DEFVAL { disabled }
::= { rlSntpConfig 3 }
rlSntpAnycastAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2),
ipv4OnlyEnabled(3),
ipv6OnlyEnabled(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Anycast Administrative state - Enable/Disable SNTP.
In case of reinitializing polling or time
synchronization this MIB is modified. The MIB can
be enabled even thought it is already enabled."
DEFVAL { disabled }
::= { rlSntpConfig 4 }
rlSntpUnicastPollState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Unicast poll state - TRUE for polled."
DEFVAL { false }
::= { rlSntpConfig 5 }
rlSntpBroadcastPollState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Broadcast poll state - TRUE for polled."
DEFVAL { false }
::= { rlSntpConfig 6 }
rlSntpAnycastPollState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP Anycast poll state - TRUE for polled."
DEFVAL { false }
::= { rlSntpConfig 7 }
rlSntpAuthenticationState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP authentication state- Enable/Disable SNTP."
DEFVAL { disabled }
::= { rlSntpConfig 8 }
rlTimeValidFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Is time valid."
DEFVAL { false }
::= { rlSntpConfig 9 }
-- ----------------------------------------------------------------------
-- Table for configuring Interfaces (Broadcast)
-- ----------------------------------------------------------------------
rlSntpConfigBroadcastTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpBroadcastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing broadcast mode information per
interface."
::= { rlSntpConfig 10 }
rlSntpBroadcastEntry OBJECT-TYPE
SYNTAX RlSntpBroadcastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Private paramters for interface:
sntp status, broadcast mode."
INDEX { rlSntpBroadcastIfIndex }
::= { rlSntpConfigBroadcastTable 1 }
RlSntpBroadcastEntry ::=
SEQUENCE {
rlSntpBroadcastIfIndex INTEGER,
rlSntpBroadcastIfAdminState INTEGER,
rlSntpBroadcastMode INTEGER,
rlSntpBroadcastPolled TruthValue,
rlSntpBroadcastAddress IpAddress,
rlSntpBroadcastStratum NTPStratum,
rlSntpBroadcastLastResp NTPTimeStamp,
rlSntpBroadcastStatus INTEGER,
rlSntpBroadcastOffset NTPTimeStamp,
rlSntpBroadcastDelay NTPSignedTimeValue,
rlSntpBroadcastRowStatus RowStatus
}
rlSntpBroadcastIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The interface addressed by this entry."
::= {rlSntpBroadcastEntry 1}
rlSntpBroadcastIfAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP interface Adminstrative state- Enable/Disable SNTP.
In case of reinitializing polling or time
synchronization this MIB is modified. The MIB can
be enabled even thought it is already enabled."
DEFVAL { disabled }
::= { rlSntpBroadcastEntry 2 }
rlSntpBroadcastMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
receive(2),
send(3),
receiveSend(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP/NTP Broadcast Mode.
none - no broadcast SNTP packets are received or sent.
Receive - host only receive SNTP packets that were sent
to broadcast address (were not directed to
the host). This is multicast mode in the RFC.
Send - host only send SNTP packets and wait for replies
directed to the host. This is anycast mode in
the RFC.
ReceiveSend - host receive broadcast messages (destination
is broadcast address in the received messages)
and send SNTP packets to wait for replies
directed to the host (destination address
of the reply is the host address). This mode
combines anycast and multicast modes in the
RFC."
DEFVAL { receiveSend }
::= { rlSntpBroadcastEntry 3 }
rlSntpBroadcastPolled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "TRUE if participating in polling cycle, else FALSE."
DEFVAL { false }
::= { rlSntpBroadcastEntry 4 }
rlSntpBroadcastAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Ip Address of a trusted SNTP server."
::= { rlSntpBroadcastEntry 5 }
rlSntpBroadcastStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpBroadcastEntry 6 }
rlSntpBroadcastLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Broadcast Last Response Time"
::= { rlSntpBroadcastEntry 7 }
rlSntpBroadcastStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Broadcast.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpBroadcastEntry 8 }
rlSntpBroadcastOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpBroadcastEntry 9 }
rlSntpBroadcastDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpBroadcastEntry 10 }
rlSntpBroadcastRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP broadcast interface
information."
::= { rlSntpBroadcastEntry 11 }
-- ----------------------------------------------------------------------
-- Table for configuring Interfaces (Anycast)
-- ----------------------------------------------------------------------
rlSntpConfigAnycastTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpAnycastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing anycast information per
interface."
::= { rlSntpConfig 11 }
rlSntpAnycastEntry OBJECT-TYPE
SYNTAX RlSntpAnycastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Private paramters for interface:
server info."
INDEX { rlSntpAnycastIfIndex }
::= { rlSntpConfigAnycastTable 1 }
RlSntpAnycastEntry ::=
SEQUENCE {
rlSntpAnycastIfIndex INTEGER,
rlSntpAnycastAddress IpAddress,
rlSntpAnycastStratum NTPStratum,
rlSntpAnycastLastResp NTPTimeStamp,
rlSntpAnycastStatus INTEGER,
rlSntpAnycastOffset NTPTimeStamp,
rlSntpAnycastDelay NTPSignedTimeValue,
rlSntpAnycastRowStatus RowStatus
}
rlSntpAnycastIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The interface addressed by this entry."
::= {rlSntpAnycastEntry 1}
rlSntpAnycastAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Ip Address of a trusted SNTP server."
::= { rlSntpAnycastEntry 2 }
rlSntpAnycastStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpAnycastEntry 3 }
rlSntpAnycastLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Anycast Last Response Time"
::= { rlSntpAnycastEntry 4 }
rlSntpAnycastStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Anycast.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpAnycastEntry 5 }
rlSntpAnycastOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAnycastEntry 6 }
rlSntpAnycastDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAnycastEntry 7 }
rlSntpAnycastRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP anycast interface
information."
::= { rlSntpAnycastEntry 8 }
-- ----------------------------------------------------------------------
-- Table for configuring Servers (Unicast)
-- ----------------------------------------------------------------------
rlSntpConfigServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing trusted SNTP servers to be queried in
unicast or broadcast mode."
::= { rlSntpConfig 12 }
rlSntpServerEntry OBJECT-TYPE
SYNTAX RlSntpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A trusted server."
INDEX { rlSntpServerAddress }
::= { rlSntpConfigServerTable 1 }
RlSntpServerEntry ::=
SEQUENCE {
rlSntpServerAddress IpAddress,
rlSntpServerPolled TruthValue,
rlSntpServerStratum NTPStratum,
rlSntpServerLastResp NTPTimeStamp,
rlSntpServerStatus INTEGER,
rlSntpServersOffset NTPTimeStamp,
rlSntpServersDelay NTPSignedTimeValue,
rlSntpServersKeyIdentifier Unsigned32,
rlSntpServerRowStatus RowStatus
}
rlSntpServerAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Ip Address of a trusted SNTP server."
::= { rlSntpServerEntry 1 }
rlSntpServerPolled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "TRUE if participating in polling cycle, else FALSE."
DEFVAL { false }
::= { rlSntpServerEntry 2 }
rlSntpServerStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpServerEntry 3 }
rlSntpServerLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Server Last Response Time"
::= { rlSntpServerEntry 4 }
rlSntpServerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Server.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpServerEntry 5 }
rlSntpServersOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpServerEntry 6 }
rlSntpServersDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpServerEntry 7 }
rlSntpServersKeyIdentifier OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Authentication key identifier. The valid range is
1-4294967295.
Value zero, means no authentication is being done."
::= { rlSntpServerEntry 8 }
rlSntpServerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP server information."
::= { rlSntpServerEntry 9 }
-- ----------------------------------------------------------------------
-- Table for configuring authentication keys
-- ----------------------------------------------------------------------
rlSntpConfigAuthenticationTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpAuthenticationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table authentication keys."
::= { rlSntpConfig 13 }
rlSntpAuthenticationEntry OBJECT-TYPE
SYNTAX RlSntpAuthenticationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Keys information for authenticationof NTP packets."
INDEX { rlSntpAuthenticationKeyID }
::= { rlSntpConfigAuthenticationTable 1 }
RlSntpAuthenticationEntry ::=
SEQUENCE {
rlSntpAuthenticationKeyID Unsigned32 (1..4294967295),
rlSntpAuthenticationKeyValue DisplayString,
rlSntpAuthenticationKeyState INTEGER,
rlSntpAuthenticationRowStatus RowStatus
}
rlSntpAuthenticationKeyID OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The key identifier. Valid rabge for key identifier
is 1-4294967295."
::= {rlSntpAuthenticationEntry 1}
rlSntpAuthenticationKeyValue OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..8))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Key value."
::= { rlSntpAuthenticationEntry 2 }
rlSntpAuthenticationKeyState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Authentication key state - Enable/Disable key."
DEFVAL { disabled }
::= { rlSntpAuthenticationEntry 3 }
rlSntpAuthenticationRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this Authentication key information."
::= { rlSntpAuthenticationEntry 4 }
rlSntpPort OBJECT-TYPE
SYNTAX INTEGER (1.. 65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "User defined SNTP port."
DEFVAL { 123 }
::= { rlSntpConfig 14 }
-- ----------------------------------------------------------------------
-- IPv6 Support
-- ----------------------------------------------------------------------
-- ----------------------------------------------------------------------
-- IPv6: Table for configuring Interfaces (Broadcast)
-- ----------------------------------------------------------------------
rlSntpConfigBroadcastInetTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpBroadcastInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing broadcast mode information per
interface."
::= { rlSntpConfig 15 }
rlSntpBroadcastInetEntry OBJECT-TYPE
SYNTAX RlSntpBroadcastInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Private paramters for interface:
sntp status, broadcast mode."
INDEX { rlSntpBroadcastInetIfIndex }
::= { rlSntpConfigBroadcastInetTable 1 }
RlSntpBroadcastInetEntry ::=
SEQUENCE {
rlSntpBroadcastInetIfIndex INTEGER,
rlSntpBroadcastInetIfAdminState INTEGER,
rlSntpBroadcastInetMode INTEGER,
rlSntpBroadcastInetPolled TruthValue,
rlSntpBroadcastInetAddressType InetAddressType,
rlSntpBroadcastInetAddress InetAddress,
rlSntpBroadcastInetStratum NTPStratum,
rlSntpBroadcastInetLastResp NTPTimeStamp,
rlSntpBroadcastInetStatus INTEGER,
rlSntpBroadcastInetOffset NTPTimeStamp,
rlSntpBroadcastInetDelay NTPSignedTimeValue,
rlSntpBroadcastInetRowStatus RowStatus,
rlSntpBroadcastInetLastReq NTPTimeStamp
}
rlSntpBroadcastInetIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The interface addressed by this entry."
::= {rlSntpBroadcastInetEntry 1}
rlSntpBroadcastInetIfAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP interface Adminstrative state- Enable/Disable SNTP.
In case of reinitializing polling or time
synchronization this MIB is modified. The MIB can
be enabled even thought it is already enabled."
DEFVAL { disabled }
::= { rlSntpBroadcastInetEntry 2 }
rlSntpBroadcastInetMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
receive(2),
send(3),
receiveSend(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "SNTP/NTP Broadcast Mode.
none - no broadcast SNTP packets are received or sent.
Receive - host only receive SNTP packets that were sent
to broadcast address (were not directed to
the host). This is multicast mode in the RFC.
Send - host only send SNTP packets and wait for replies
directed to the host. This is anycast mode in
the RFC.
ReceiveSend - host receive broadcast messages (destination
is broadcast address in the received messages)
and send SNTP packets to wait for replies
directed to the host (destination address
of the reply is the host address). This mode
combines anycast and multicast modes in the
RFC."
DEFVAL { receiveSend }
::= { rlSntpBroadcastInetEntry 3 }
rlSntpBroadcastInetPolled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "TRUE if participating in polling cycle, else FALSE."
DEFVAL { false }
::= { rlSntpBroadcastInetEntry 4 }
rlSntpBroadcastInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Inet Address Type of a trusted SNTP server."
::= { rlSntpBroadcastInetEntry 5 }
rlSntpBroadcastInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Inet Address of a trusted SNTP server."
::= { rlSntpBroadcastInetEntry 6 }
rlSntpBroadcastInetStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpBroadcastInetEntry 7 }
rlSntpBroadcastInetLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Broadcast Last Response Time"
::= { rlSntpBroadcastInetEntry 8 }
rlSntpBroadcastInetStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Broadcast.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpBroadcastInetEntry 9 }
rlSntpBroadcastInetOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpBroadcastInetEntry 10 }
rlSntpBroadcastInetDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpBroadcastInetEntry 11 }
rlSntpBroadcastInetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP broadcast interface
information."
::= { rlSntpBroadcastInetEntry 12 }
rlSntpBroadcastInetLastReq OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Broadcast Last Request Time"
::= { rlSntpBroadcastInetEntry 13 }
-- ----------------------------------------------------------------------
-- IPv6: Table for configuring Interfaces (Anycast)
-- ----------------------------------------------------------------------
rlSntpConfigAnycastInetTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpAnycastInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing anycast information per
interface."
::= { rlSntpConfig 16 }
rlSntpAnycastInetEntry OBJECT-TYPE
SYNTAX RlSntpAnycastInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Private paramters for interface:
server info."
INDEX { rlSntpAnycastInetIfIndex }
::= { rlSntpConfigAnycastInetTable 1 }
RlSntpAnycastInetEntry ::=
SEQUENCE {
rlSntpAnycastInetIfIndex INTEGER,
rlSntpAnycastInetAddressType InetAddressType,
rlSntpAnycastInetAddress InetAddress,
rlSntpAnycastInetStratum NTPStratum,
rlSntpAnycastInetLastResp NTPTimeStamp,
rlSntpAnycastInetStatus INTEGER,
rlSntpAnycastInetOffset NTPTimeStamp,
rlSntpAnycastInetDelay NTPSignedTimeValue,
rlSntpAnycastInetRowStatus RowStatus,
rlSntpAnycastInetLastReq NTPTimeStamp
}
rlSntpAnycastInetIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The interface addressed by this entry."
::= {rlSntpAnycastInetEntry 1}
rlSntpAnycastInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Inet Address Type of a trusted SNTP server."
::= { rlSntpAnycastInetEntry 2 }
rlSntpAnycastInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Inet Address of a trusted SNTP server."
::= { rlSntpAnycastInetEntry 3 }
rlSntpAnycastInetStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpAnycastInetEntry 4 }
rlSntpAnycastInetLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Anycast Last Response Time"
::= { rlSntpAnycastInetEntry 5 }
rlSntpAnycastInetStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Anycast.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpAnycastInetEntry 6 }
rlSntpAnycastInetOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAnycastInetEntry 7 }
rlSntpAnycastInetDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAnycastInetEntry 8 }
rlSntpAnycastInetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP anycast interface
information."
::= { rlSntpAnycastInetEntry 9 }
rlSntpAnycastInetLastReq OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Anycast Last Request Time"
::= { rlSntpAnycastInetEntry 10 }
-- ----------------------------------------------------------------------
-- IPv6: Table for configuring Servers (Unicast)
-- ----------------------------------------------------------------------
rlSntpConfigServerInetTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpServerInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing trusted SNTP servers to be queried in
unicast or broadcast mode."
::= { rlSntpConfig 17 }
rlSntpServerInetEntry OBJECT-TYPE
SYNTAX RlSntpServerInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A trusted server."
INDEX { rlSntpServerInetAddressType,
rlSntpServerInetAddress }
::= { rlSntpConfigServerInetTable 1 }
RlSntpServerInetEntry ::=
SEQUENCE {
rlSntpServerInetAddressType InetAddressType,
rlSntpServerInetAddress InetAddress,
rlSntpServerInetPolled TruthValue,
rlSntpServerInetStratum NTPStratum,
rlSntpServerInetLastResp NTPTimeStamp,
rlSntpServerInetStatus INTEGER,
rlSntpServerInetOffset NTPTimeStamp,
rlSntpServerInetDelay NTPSignedTimeValue,
rlSntpServerInetKeyIdentifier Unsigned32,
rlSntpServerInetRowStatus RowStatus,
rlSntpServerInetLastReq NTPTimeStamp
}
rlSntpServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Inet Address Type of a trusted SNTP server."
::= { rlSntpServerInetEntry 1 }
rlSntpServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Inet Address of a trusted SNTP server."
::= { rlSntpServerInetEntry 2 }
rlSntpServerInetPolled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "TRUE if participating in polling cycle, else FALSE."
DEFVAL { false }
::= { rlSntpServerInetEntry 3 }
rlSntpServerInetStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpServerInetEntry 4 }
rlSntpServerInetLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Server Last Response Time"
::= { rlSntpServerInetEntry 5 }
rlSntpServerInetStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Server.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpServerInetEntry 6 }
rlSntpServerInetOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpServerInetEntry 7 }
rlSntpServerInetDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpServerInetEntry 8 }
rlSntpServerInetKeyIdentifier OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Authentication key identifier. The valid range is
1-4294967295.
Value zero, means no authentication is being done."
::= { rlSntpServerInetEntry 9 }
rlSntpServerInetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The Status of this SNTP server information."
::= { rlSntpServerInetEntry 10 }
rlSntpServerInetLastReq OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Server Last Request Time"
::= { rlSntpServerInetEntry 11 }
rlSntpAllServerInetTable OBJECT-TYPE
SYNTAX SEQUENCE OF RlSntpAllServerInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table containing all SNTP servers (for example: statically
configured, dynamically configured) to be queried in unicast
or broadcast mode."
::= { rlSntpConfig 18 }
rlSntpAllServerInetEntry OBJECT-TYPE
SYNTAX RlSntpAllServerInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A server entry."
INDEX { rlSntpAllServerSource,
rlSntpAllServerIfIndex,
rlSntpAllServerPreference,
rlSntpAllServerInetAddressType,
rlSntpAllServerInetAddress
}
::= { rlSntpAllServerInetTable 1 }
RlSntpAllServerInetEntry ::=
SEQUENCE {
rlSntpAllServerSource INTEGER,
rlSntpAllServerIfIndex InterfaceIndex,
rlSntpAllServerPreference INTEGER,
rlSntpAllServerInetAddressType InetAddressType,
rlSntpAllServerInetAddress InetAddress,
rlSntpAllServerInetPolled TruthValue,
rlSntpAllServerInetStratum NTPStratum,
rlSntpAllServerInetLastResp NTPTimeStamp,
rlSntpAllServerInetStatus INTEGER,
rlSntpAllServerInetOffset NTPTimeStamp,
rlSntpAllServerInetDelay NTPSignedTimeValue,
rlSntpAllServerInetKeyIdentifier Unsigned32,
rlSntpAllServerInetLastReq NTPTimeStamp
}
rlSntpAllServerSource OBJECT-TYPE
SYNTAX INTEGER {
static(1),
dhcpv6(2),
dhcpv4(3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The SNTP server source: static means manually defined,
dhcpv6 means learnt from DHCP. Only static entries are
stored in CDB."
::= { rlSntpAllServerInetEntry 1 }
rlSntpAllServerIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The ifIndex from which the SNTP server configuration was
received (for dhcpv6 configurations). For static entries
the value of this field will always be 1. "
::= { rlSntpAllServerInetEntry 2 }
rlSntpAllServerPreference OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The preference of SNTP server (for dhcpv6 configurations).
For static entries the value of this field will always be 0. "
::= { rlSntpAllServerInetEntry 3 }
rlSntpAllServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "SNTP server inet address type."
::= { rlSntpAllServerInetEntry 4 }
rlSntpAllServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "SNTP server inet address."
::= { rlSntpAllServerInetEntry 5 }
rlSntpAllServerInetPolled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "TRUE if participating in polling cycle, else FALSE."
DEFVAL { false }
::= { rlSntpAllServerInetEntry 6 }
rlSntpAllServerInetStratum OBJECT-TYPE
SYNTAX NTPStratum
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The stratum of this server."
::= { rlSntpAllServerInetEntry 7 }
rlSntpAllServerInetLastResp OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Server Last Response Time"
::= { rlSntpAllServerInetEntry 8 }
rlSntpAllServerInetStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
inProcess(2),
up(3),
down(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Operational State of the remote IP Address of
the SNTP Server.
unknown - requests were not sent yet.
inProcess - replies were not received yet.
up - server sent SNTP packets.
down - server stopped sending SNTP packets."
DEFVAL { unknown }
::= { rlSntpAllServerInetEntry 9 }
rlSntpAllServerInetOffset OBJECT-TYPE
SYNTAX NTPTimeStamp
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated offset of the server's clock relative to
the local clock, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAllServerInetEntry 10 }
rlSntpAllServerInetDelay OBJECT-TYPE
SYNTAX NTPSignedTimeValue
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The estimated round-trip delay of the server's clock
relative to the local clock over the network path
between them, in seconds. The host determines the
value of this object using the algorithm described in
RFC 2030."
::= { rlSntpAllServerInetEntry 11 }
rlSntpAllServerInetKeyIdentifier OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Authentication key identifier. The valid range is
1-4294967295.
Value zero, means no authentication is being done."
::= { rlSntpAllServerInetEntry 12 }
rlSntpAllServerInetLastReq OBJECT-TYPE
SYNTAX NTPTimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP Server Last Request Time"
::= { rlSntpAllServerInetEntry 13 }
rlSntpRestoreDefaultServers OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Setting this scalar to true restores sntp default unicast servers.
Meaning: all manually configured servers are deleted, and the
default SNTP servers are recreated with their default values.
This is an 'action' scalar."
::= { rlSntpConfig 19 }
rlSntpTimeSinceLastSync OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "SNTP time in seconds since last sync."
::= { rlSntpConfig 20 }
END
Reference in New Issue Copy Permalink