mibs/MIBS/eaton/EATON-EMP-MIB

EATON-EMP-MIB DEFINITIONS ::= BEGIN

IMPORTS
      MODULE-IDENTITY, OBJECT-TYPE, Integer32 
           FROM SNMPv2-SMI
      DisplayString
           FROM SNMPv2-TC
      MODULE-COMPLIANCE, OBJECT-GROUP
           FROM SNMPv2-CONF
      xupsEnvironment
           FROM EATON-OIDS;

eatonEMPMIB MODULE-IDENTITY
    LAST-UPDATED "200703120000Z"
    ORGANIZATION "Eaton Corporation"
    CONTACT-INFO
        "Eaton Power Quality Technical Support (PQTS) group
            www.eaton.com/powerxpert 
            Technical Resource Center phone numbers 
			United States:  1.800.843.9433 or 919.870.3028
			Canada:  1.800.461.9166 ext. 260
			All other countries:  Call your local service representative." 
    DESCRIPTION
        "The MIB module for Eaton Environment Monitoring Probes (EMP).
         The elements of this MIB have been extracted from the 
         Eaton PowerMIB and placed in this separate MIB file for convenience.

        Copyright (C) Eaton Corporation (2007)."

    REVISION        "200703120000Z"
    DESCRIPTION
        "Initial Version of eatonEMPMIB."

    ::= { xupsEnvironment 0 }

--  ::= { enterprises 534  8  1  }
-- eatonEMPMIB { iso org(3) dod(6) internet(1) private(4)
--       enterprises(1) eaton(534) xupsMIB(1) xupsEnvironment(6) (0) }


--
-- EMP group
--
-- The objects defined in this group are provided by the EMP.
-- They are Temperature and Humidity readings and alarming limits,
-- and the (two) contacts readings and setup information.
-- These objects are considered "Remote" since the EMP is a
-- separate probe from the Eaton device or gateway it is connected to.
--
-- Notices/Traps: two different types of traps may be sent in response
-- to EMP changes, depending upon the type of device the EMP is attached to.
-- If connected to a UPS device, normally the PowerMIB traps are sent:
--      xupstdRemoteTempBad
--      xupstdRemoteHumidityBad
--      xupstdContactActiveNotice
--      xupstdContactInactiveNotice
-- If connected to a Toolkit-enabled PowerXpert Gateway, Toolkit traps are sent:
--      powerChainCriticalAlarm
--      powerChainCautionaryAlarm
--      powerChainAlarmAcknowledged
--      powerChainAlarmCleared
-- Both sets of traps are defined in their respective MIB files.


xupsEnvRemoteTemp OBJECT-TYPE
    SYNTAX  Integer32 (-100..200)   
    UNITS       "degrees Centigrade"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The reading of an EMP's temperature sensor."
    ::= { xupsEnvironment  5 }

xupsEnvRemoteHumidity OBJECT-TYPE
    SYNTAX  Integer32 (0..100)  
    UNITS       "percent"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The reading of an EMP's humidity sensor."
    ::= { xupsEnvironment  6 }

--
-- The Environmental Contact Sensing Table
--      Contains the table for monitoring all contacts (digital 
--      inputs, normally 2 in an EMP).
--

xupsEnvNumContacts OBJECT-TYPE
    SYNTAX  Integer32 (1..1024)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The number of Contacts in the xupsContactSenseTable.
        This object indicates the number of rows in the 
        xupsContactSenseTable."
    ::= { xupsEnvironment  7 }

xupsContactSenseTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF XupsContactsTableEntry
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
       "A list of Contact Sensing table entries.  
        The number of entries is given by the value of 
        xupsEnvNumContacts."
    ::= { xupsEnvironment  8 }

xupsContactsTableEntry OBJECT-TYPE
    SYNTAX  XupsContactsTableEntry
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
       "An entry containing information applicable 
        to a particular Contact input."
    INDEX   { xupsContactIndex }
    ::= { xupsContactSenseTable  1 }

XupsContactsTableEntry ::= SEQUENCE {
    xupsContactIndex   Integer32,
    xupsContactType    INTEGER,
    xupsContactState   INTEGER,
    xupsContactDescr   DisplayString
    }

xupsContactIndex OBJECT-TYPE
    SYNTAX  Integer32 (1..1024)
    MAX-ACCESS  read-only           -- actually not-accessible
    STATUS  current
    DESCRIPTION
       "The Contact identifier; identical to the Contact Number.
        This object is not-accessible to MIB browsers, but had to be changed to
        read-only to satisfy SMIv2 syntax checkers if it is included in traps."
    ::= { xupsContactsTableEntry  1 }

xupsContactType OBJECT-TYPE
    SYNTAX  INTEGER {
        normallyOpen(1),            -- or Input Normally High
        normallyClosed(2),          -- or Input Normally Low
        anyChange(3),               -- No normal Open/Closed state
        notUsed(4)                  -- Contact not in service or not alarming
        }
    MAX-ACCESS  read-write
    STATUS  current
    DESCRIPTION
       "The normal state for this contact.  The 'other' (not 'Normally')
        state is the Active state for generating the xupstdContactActiveNotice
        trap.  If anyChange(3) is selected, then this trap is sent
        any time the contact changes to either Open or Closed.
        No traps are sent if the Contact is set to notUsed(4).
        In many cases, the configuration for Contacts may be done by other 
        means, so this object may be read-only."
    ::= { xupsContactsTableEntry  2 }

xupsContactState OBJECT-TYPE
    SYNTAX  INTEGER {
        open(1),
        closed(2),
        openWithNotice(3),
        closedWithNotice(4)
        }
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
       "The current state of the Contact input;
        the value is based on the open/closed input state 
        and the setting for xupsContactType.
        When entering the openWithNotice(3) and closedWithNotice(4) 
        states, no entries added to the xupsAlarmTable, but
        the xupstdContactActiveNotice trap is sent."
    ::= { xupsContactsTableEntry  3 }

xupsContactDescr OBJECT-TYPE
    SYNTAX  DisplayString (SIZE (0..63))
    MAX-ACCESS  read-write
    STATUS  current
    DESCRIPTION
       "A label identifying the Contact.  This object should be
        set by the administrator."
    ::= { xupsContactsTableEntry  4 }

xupsEnvRemoteTempLowerLimit OBJECT-TYPE
    SYNTAX  Integer32 (-100..200) 
    UNITS       "degrees Centigrade"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The Lower Limit of the EMP temperature; if xupsEnvRemoteTemp 
        falls below this value, the xupsRemoteTempBad alarm will occur."
    ::= { xupsEnvironment  9 }

xupsEnvRemoteTempUpperLimit OBJECT-TYPE
    SYNTAX  Integer32 (-100..200) 
    UNITS       "degrees Centigrade"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The Upper Limit of the EMP temperature; if xupsEnvRemoteTemp 
        rises above this value, the xupsRemoteTempBad alarm will occur.
        This value should be greater than xupsEnvRemoteTempLowerLimit."
    ::= { xupsEnvironment  10 }

xupsEnvRemoteHumidityLowerLimit OBJECT-TYPE
    SYNTAX  Integer32 (0..100) 
    UNITS       "percent"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The Lower Limit of the EMP humidity reading; if xupsEnvRemoteHumidity
        falls below this value, the xupsRemoteHumidityBad alarm will occur."
    ::= { xupsEnvironment  11 }

xupsEnvRemoteHumidityUpperLimit OBJECT-TYPE
    SYNTAX  Integer32 (0..100) 
    UNITS       "percent"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The Upper Limit of the EMP humidity reading; if xupsEnvRemoteHumidity 
        rises above this value, the xupsRemoteHumidityBad alarm will occur.
        This value should be greater than xupsEnvRemoteHumidityLowerLimit."
    ::= { xupsEnvironment  12 }


--
-- Traps / Notifications for the EMP in the PowerMIB style
-- The special EMP traps are not normally provided by Power Xpert Gateways (which use
-- the PXG-style traps instead) but could be provided by PowerMIB implementations
-- These are found in the PowerMIB:
--    xupstdContactActiveNotice   
--    xupstdContactInactiveNotice 
--    xupstdRemoteTempBad         
--    xupstdRemoteHumidityBad     


--
-- Conformance-related definitions
--
eatonEMPConformance OBJECT IDENTIFIER ::= { eatonEMPMIB 2 }

eatonEMPGroup  OBJECT-GROUP
    OBJECTS { xupsEnvRemoteTemp, xupsEnvRemoteHumidity,
              xupsEnvRemoteTempLowerLimit, xupsEnvRemoteTempUpperLimit,
              xupsEnvRemoteHumidityLowerLimit, xupsEnvRemoteHumidityUpperLimit  }
    STATUS  current
    DESCRIPTION
        "The EMP scalar objects."
    ::= { eatonEMPConformance 1 }

eatonEMPTableGroup  OBJECT-GROUP
    OBJECTS { xupsEnvNumContacts, xupsContactIndex, xupsContactType,    
              xupsContactState, xupsContactDescr }
    STATUS  current
    DESCRIPTION
        "The EMP Contacts Table objects."
    ::= { eatonEMPConformance 2 }


eatonEMPSimpleCompliance MODULE-COMPLIANCE
    STATUS     current
    DESCRIPTION
       "The compliance statement for a normal EMP."
    MODULE -- this module
       MANDATORY-GROUPS  { eatonEMPGroup, eatonEMPTableGroup }
    ::= { eatonEMPConformance 4 }





END