mibs/MIBS/mitsubishi/UPS-MIB

-- Mitsubishi.mib  - MIB file for Mitsubishi UPSs

UPS-MIB DEFINITIONS ::= BEGIN

IMPORTS
        TRAP-TYPE
                FROM RFC-1215
        DisplayString
                FROM RFC1213-MIB
        OBJECT-TYPE
                FROM RFC-1212
        Gauge, Counter, TimeTicks, mgmt
                FROM RFC1155-SMI
            ;

PositiveInteger		::= INTEGER
NonNegativeInteger 	::= INTEGER
TimeStamp 			::= TimeTicks
TimeInterval 		::= INTEGER (0..2147483647)
TestAndIncr 		::= INTEGER (0..2147483647)
AutonomousType 		::= DisplayString

Tag			OBJECT IDENTIFIER ::= { enterprises 13891 }
MitsubishiUPS 	OBJECT IDENTIFIER ::= { Tag 101 }

upsIdent OBJECT IDENTIFIER ::= { MitsubishiUPS 1 }

upsIdentManufacturer OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The name of the UPS manufacturer."
    ::= { upsIdent 1 }

upsIdentModel OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The UPS Model designation."
    ::= { upsIdent 2 }

upsIdentUPSSoftwareVersion OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The UPS firmware/software version(s).  This variable
            may or may not have the same value as
            upsIdentAgentSoftwareVersion in some implementations."
    ::= { upsIdent 3 }

upsIdentAgentSoftwareVersion OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The UPS agent software version.  This variable may or may
             not have the same value as upsIdentUPSSoftwareVersion in 
             some implementations."
    ::= { upsIdent 4 }

upsIdentName OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "A string identifying the UPS.  This object should be
            set by the administrator."
    ::= { upsIdent 5 }

upsIdentAttachedDevices OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "A string identifying the devices attached to the output
            of the UPS.  This object should be set by the administrator."
    ::= { upsIdent 6 }

upsBattery OBJECT IDENTIFIER ::= { MitsubishiUPS 2 }

upsBatteryStatus OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        unknown(1),
        batteryNormal(2),
        batteryLow(3),
        batteryDepleted(4)
    }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The indication of the capacity remaining in the UPS batteries.   
            A value of batteryNormal indicates a normal battery condition.  
            A value of batteryLow indicates the remaining battery run-time 
            will not maintain the output load for an extended period of time.
            A value of batteryDepleted indicates that the UPS will be unable
            to sustain the present load when and if the utility power is lost." 
    ::= { upsBattery 1 }

upsSecondsOnBattery OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS seconds
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "If the unit is on battery power, the elapsed time in seconds
            since the UPS last switched to battery power, or the time since 
            the network management system was last restarted, whichever is less.  
            Zero shall be returned if the unit is not on battery power."
    ::= { upsBattery 2 }

upsEstimatedMinutesRemaining OBJECT-TYPE
    SYNTAX  PositiveInteger     -- UNITS minutes
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "An estimate of the time in minutes until the battery is depleted
            under the present load conditions if the utility power is off and 
            remains off, or if it were to be lost and remain off."
    ::= { upsBattery 3 }

upsEstimatedChargeRemaining OBJECT-TYPE
    SYNTAX  INTEGER     -- UNITS percent
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "An estimate of the battery charge remaining expressed as a 
            percent of full charge."
    ::= { upsBattery 4 }

upsBatteryVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Volt DC
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the present battery voltage (0.1 Volt DC)."
    ::= { upsBattery 5 }

upsBatteryCurrent OBJECT-TYPE
    SYNTAX  INTEGER (-2147483648..2147483647)   -- UNITS 0.1 Amp DC
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present battery current (0.1 Amp DC)."
    ::= { upsBattery 6 }

upsBatteryTemperature OBJECT-TYPE
    SYNTAX  INTEGER (-2147483648..2147483647)   -- UNITS degrees Centigrade
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The ambient temperature at or near the UPS Battery casing (degrees Centigrade)."
    ::= { upsBattery 7 }

upsInput OBJECT IDENTIFIER ::= { MitsubishiUPS 3 }

upsInputLineBads OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "A count of the number of times the input entered an
            out-of-tolerance condition as defined by the manufacturer.  
            This count is incremented by one each time the input 
            transitions from zero out-of-tolerance lines to one or more 
            input lines out-of-tolerance."
    ::= { upsInput 1 }

upsInputNumLines OBJECT-TYPE
    SYNTAX  NonNegativeInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The number of input lines utilized in this device.  This
            variable indicates the number of rows in the input table."
    ::= { upsInput 2 }

upsInputTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF UpsInputEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "A list of input table entries.  The number of entries
            is given by the value of upsInputNumLines."
    ::= { upsInput 3 }

upsInputEntry OBJECT-TYPE
    SYNTAX  UpsInputEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "An entry containing information applicable to a
            particular input line."
    INDEX   { upsInputLineIndex }
    ::= { upsInputTable  1 }

UpsInputEntry ::=
    SEQUENCE 
    {
        upsInputLineIndex PositiveInteger,
        upsInputFrequency NonNegativeInteger,
        upsInputVoltage   NonNegativeInteger,
        upsInputCurrent   NonNegativeInteger,
        upsInputTruePower NonNegativeInteger
    }

upsInputLineIndex OBJECT-TYPE
    SYNTAX  PositiveInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The input line identifier."
    ::= { upsInputEntry 1 }

upsInputFrequency OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Hertz
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present input frequency (0.1 Hertz)."
    ::= { upsInputEntry 2 }

upsInputVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Volt
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the present input voltage (0.1 RMS Volt)."
    ::= { upsInputEntry 3 }

upsInputCurrent OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Amp
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the present input current (0.1 RMS Amp)."
    ::= { upsInputEntry 4 }

upsInputTruePower OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS Watts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the present input true power (watts)."
    ::= { upsInputEntry 5 }

upsOutput OBJECT IDENTIFIER ::= { MitsubishiUPS 4 }

upsOutputSource OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        other(1),
        none(2),
        normal(3),
        bypass(4),
        battery(5),
        booster(6),
        reducer(7)
    }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present source of output power.  A value of none (2) indicates
            there is no source of output power (and therefore no output power), 
            for example, the system has opened the output breaker."
    ::= { upsOutput 1 }

upsOutputFrequency OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Hertz
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present output frequency (0.1 Hertz)."
    ::= { upsOutput 2 }

upsOutputNumLines OBJECT-TYPE
    SYNTAX  NonNegativeInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The number of output lines utilized in this device.  This
            variable indicates the number of rows in the output table."
    ::= { upsOutput 3 }

upsOutputTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF UpsOutputEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "A list of output table entries.  The number of
            entries is given by the value of upsOutputNumLines."
    ::= { upsOutput 4 }

upsOutputEntry OBJECT-TYPE
    SYNTAX  UpsOutputEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "An entry containing information applicable to a
            particular output line."
    INDEX   { upsOutputLineIndex }
    ::= { upsOutputTable 1 }

UpsOutputEntry ::=
    SEQUENCE 
    {
        upsOutputLineIndex          PositiveInteger,
        upsOutputVoltage            NonNegativeInteger,
        upsOutputCurrent            NonNegativeInteger,
        upsOutputPower              NonNegativeInteger,
        upsOutputPercentLoad        INTEGER
    }

upsOutputLineIndex OBJECT-TYPE
    SYNTAX  PositiveInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The output line identifier."
    ::= { upsOutputEntry 1 }

upsOutputVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Volts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present output voltage (0.1 RMS Volt)."
    ::= { upsOutputEntry 2 }

upsOutputCurrent OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Amp
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present output current (0.1 RMS Amp)."
    ::= { upsOutputEntry 3 }

upsOutputPower OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS Watts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present output true power (watts)."
    ::= { upsOutputEntry 4 }

upsOutputPercentLoad OBJECT-TYPE
    SYNTAX  INTEGER     -- UNITS percent
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The percentage of the UPS power capacity presently being 
            used on this output line (the greater of the percent load 
            of true power capacity and the percent load of VA."
    ::= { upsOutputEntry 5 }

upsBypass OBJECT IDENTIFIER ::= { MitsubishiUPS 5 }

upsBypassFrequency OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Hertz
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present bypass frequency."
    ::= { upsBypass 1 }

upsBypassNumLines OBJECT-TYPE
    SYNTAX  NonNegativeInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The number of bypass lines utilized in this device.  This
            entry indicates the number of rows in the bypass table."
    ::= { upsBypass 2 }

upsBypassTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF UpsBypassEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "A list of bypass table entries.  The number of entries
            is given by the value of upsBypassNumLines."
    ::= { upsBypass 3 }

upsBypassEntry OBJECT-TYPE
    SYNTAX  UpsBypassEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "An entry containing information applicable to a
            particular bypass input."
    INDEX   { upsBypassLineIndex }
    ::= { upsBypassTable 1 }

UpsBypassEntry ::=
    SEQUENCE 
    {
        upsBypassLineIndex          PositiveInteger,
        upsBypassVoltage            NonNegativeInteger,
        upsBypassCurrent            NonNegativeInteger,
        upsBypassPower              NonNegativeInteger
    }

upsBypassLineIndex OBJECT-TYPE
    SYNTAX  PositiveInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The bypass line identifier."
    ::= { upsBypassEntry 1 }

upsBypassVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Volts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present bypass voltage (0.1 RMS Volt)."
    ::= { upsBypassEntry 2 }

upsBypassCurrent OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 RMS Amp
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present bypass current (0.1 RMS Amp)."
    ::= { upsBypassEntry 3 }

upsBypassPower OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS Watts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present true power conveyed by the bypass (watts)."
    ::= { upsBypassEntry 4 }

upsAlarm OBJECT IDENTIFIER ::= { MitsubishiUPS 6 }

upsAlarmsPresent OBJECT-TYPE
    SYNTAX  Gauge
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The present number of active alarm conditions."
    ::= { upsAlarm 1 }

upsAlarmTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF UpsAlarmEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "A list of alarm table entries.  Alarms are named by 
            an OBJECT IDENTIFIER, upsAlarmDescr, to allow a single 
            table to reflect well known alarms plus alarms defined 
            by a particular implementation, i.e., as documented in
            the private enterprise MIB definition for the device.  
            No two rows will have the same value of upsAlarmDescr,
            since alarms define conditions.  In order to meet this
            requirement, care should be taken in the definition of
            alarm conditions to insure that a system cannot enter
            the same condition multiple times simultaneously.

            The number of rows in the table at any given time is
            reflected by the value of upsAlarmsPresent."
    ::= { upsAlarm 2 }

upsAlarmEntry OBJECT-TYPE
    SYNTAX  UpsAlarmEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
           "An entry containing information applicable to a
            particular alarm."
    INDEX   { upsAlarmId }
    ::= { upsAlarmTable 1 }

UpsAlarmEntry ::=
    SEQUENCE 
    {
        upsAlarmId            PositiveInteger,
        upsAlarmDescr         AutonomousType,
        upsAlarmTime          TimeStamp
    }

upsAlarmId OBJECT-TYPE
    SYNTAX  PositiveInteger
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "A unique identifier for an alarm condition.  This
            value must remain constant."
    ::= { upsAlarmEntry  1 }

upsAlarmDescr OBJECT-TYPE
    SYNTAX  AutonomousType
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "A reference to an alarm description object.  The object
            referenced should not be accessible, but rather be used
            to provide a unique description of the alarm condition."
    ::= { upsAlarmEntry 2 }

upsAlarmTime OBJECT-TYPE
    SYNTAX  TimeStamp
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The value of sysUpTime when the alarm condition was
            detected.  If the alarm condition was detected at the
            time of agent startup and presumably existed before
            agent startup, the value of upsAlarmTime shall equal 0."
    ::= { upsAlarmEntry 3 }

  upsAlarmID OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "A unique identifier for an alarm condition.  This
               value must remain constant."
      ::= { upsAlarm 4 }

  upsAlarmDESCR OBJECT-TYPE
      SYNTAX DisplayString (SIZE(0..63))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "A reference to an alarm description object.  The object
               references should not be accessible, but rather be used
               to provide a unique description of the alarm condition."
      ::= { upsAlarm 5 }

upsWellKnownAlarms OBJECT IDENTIFIER ::= { upsAlarm 3 }

upsAlarmBatteryBad OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "One or more batteries have been determined to require
               replacement."
      ::= { upsWellKnownAlarms 1 }

upsAlarmOnBattery OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "The UPS is drawing power from the batteries."
      ::= { upsWellKnownAlarms 2 }

  upsAlarmLowBattery OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The remaining battery run-time is less than or equal
                to upsConfigLowBattTime."
      ::= { upsWellKnownAlarms 3 }

  upsAlarmDepletedBattery OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "The UPS will be unable to sustain the present load
               when and if the utility power is lost."
      ::= { upsWellKnownAlarms 4 }

  upsAlarmTempBad OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "A temperature is out of tolerance."
      ::= { upsWellKnownAlarms 5 }

   upsAlarmInputBad OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "An input condition is out of tolerance."
       ::= { upsWellKnownAlarms  6 }

   upsAlarmOutputBad OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "An output condition (other than OutputOverload) is
               out of tolerance."
       ::= { upsWellKnownAlarms  7 }

  upsAlarmOutputOverload OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "The output load exceeds the UPS output capacity."
      ::= { upsWellKnownAlarms 8 }

    upsAlarmOnBypass OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "The Bypass is presently engaged on the UPS."
       ::= { upsWellKnownAlarms  9 }

   upsAlarmBypassBad OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "The Bypass is out of tolerance."
       ::= { upsWellKnownAlarms 10 }

 upsAlarmOutputOffAsRequested OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The UPS has shut down as requested, i.e., the output
                is off."
      ::= { upsWellKnownAlarms 11 }

upsAlarmUpsOffAsRequested OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "The entire UPS has shutdown as commanded."
       ::= { upsWellKnownAlarms 12 }

upsAlarmChargerFailed OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "An uncorrected problem has been detected within the
                UPS charger subsystem."
       ::= { upsWellKnownAlarms 13 }

upsAlarmUpsOutputOff OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The output of the UPS is in the off state."
      ::= { upsWellKnownAlarms 14 }

upsAlarmUpsSystemOff OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "The UPS system is in the off state."
       ::= { upsWellKnownAlarms 15 }

upsAlarmFanFailure OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The failure of one or more fans in the UPS has been
               detected."
       ::= { upsWellKnownAlarms 16 }

upsAlarmFuseFailure OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The failure of one or more fuses has been detected."
      ::= { upsWellKnownAlarms 17 }

upsAlarmGeneralFault OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "A general fault in the UPS has been detected."
      ::= { upsWellKnownAlarms 18 }

 upsAlarmDiagnosticTestFailed OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "The result of the last diagnostic test indicates a
               failure."
      ::= { upsWellKnownAlarms 19 }

  upsAlarmCommunicationsLost OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "A problem has been encountered in the
               communications between the agent and the UPS."
      ::= { upsWellKnownAlarms 20 }

upsAlarmAwaitingPower OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
               "The UPS output is off and the UPS is awaiting the
                return of input power."
      ::= { upsWellKnownAlarms 21 }

 upsAlarmShutdownPending OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
              "A upsShutdownAfterDelay countdown is underway."
      ::= { upsWellKnownAlarms 22 }

  upsAlarmShutdownImminent OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "The UPS will turn off power to the load in less than
                5 seconds; this may be either a timed shutdown or a
                low battery shutdown."
      ::= { upsWellKnownAlarms 23 }

  upsAlarmTestInProgress OBJECT-TYPE
      SYNTAX INTEGER
      ACCESS read-only
      STATUS mandatory
       DESCRIPTION
               "A test is in progress, as initiated and indicated by
                the Test Group.  Tests initiated via other
                implementation-specific mechanisms can indicate the
                presence of the testing in the alarm table, if
                desired, via a OBJECT-TYPE macro in the MIB
                document specific to that implementation and are
                outside the scope of this OBJECT-TYPE."
       ::= { upsWellKnownAlarms 24 }

upsTest OBJECT IDENTIFIER ::= { MitsubishiUPS 7 }

  upsTestId OBJECT-TYPE
      SYNTAX OBJECT IDENTIFIER 
      ACCESS read-write
      STATUS mandatory
      DESCRIPTION
              "The test named by an OBJECT IDENTIFIER which
               allows a standard mechanism for the initiation of
               a test, including the well known tests identified in
               this document."
      ::= { upsTest 1 }

upsTestSpinLock OBJECT-TYPE
    SYNTAX  TestAndIncr
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "A spin lock on the test subsystem."
    ::= { upsTest 2 }

upsTestResultsSummary OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        donePass(1),
        doneWarning(2),
        doneError(3),
        aborted(4),
        inProgress(5),
        noTestsInitiated(6)
    }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The results of the current or last UPS diagnostics
            test performed.  The values for donePass(1),
            doneWarning(2), and doneError(3) indicate that the
            test completed either successfully, with a warning, or
            with an error, respectively.  The value aborted(4) is
            returned for tests which are aborted by setting the
            value of upsTestId to upsTestAbortTestInProgress.
            Tests which have not yet concluded are indicated by
            inProgress(5).  The value noTestsInitiated(6)
            indicates that no previous test results are available,
            such as is the case when no tests have been run since
            the last reinitialization of the network management
            subsystem and the system has no provision for non-
            volatile storage of test results."
    ::= { upsTest 3 }

upsTestResultsDetail OBJECT-TYPE
    SYNTAX  DisplayString
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "Additional information about upsTestResultsSummary.
            If no additional information available, a zero length
            string is returned."
    ::= { upsTest 4 }

upsTestStartTime OBJECT-TYPE
    SYNTAX  TimeStamp
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The value of sysUpTime at the time the test in
            progress was initiated, or, if no test is in progress,
            the time the previous test was initiated.  If the
            value of upsTestResultsSummary is noTestsInitiated(6),
            upsTestStartTime has the value 0."
    ::= { upsTest 5 }

upsTestElapsedTime OBJECT-TYPE
    SYNTAX  TimeInterval
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The amount of time, in TimeTicks, since the test in
            progress was initiated, or, if no test is in progress,
            the previous test took to complete.  If the value of
            upsTestResultsSummary is noTestsInitiated(6),
            upsTestElapsedTime has the value 0."
    ::= { upsTest 6 }

upsWellKnownTests OBJECT IDENTIFIER ::= { upsTest  7 }

upsTestNoTestsInitiated OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
           "No tests have been initiated and no test is in progress."
    ::= { upsWellKnownTests 1 }

upsTestAbortTestInProgress OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
           "The test in progress is to be aborted / the test in
            progress was aborted."
    ::= { upsWellKnownTests 2 }

upsTestGeneralSystemsTest OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
           "The manufacturer's standard test of UPS device systems."
    ::= { upsWellKnownTests  3 }

upsTestQuickBatteryTest OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
           "A test that is sufficient to determine if the battery
            needs replacement."
    ::= { upsWellKnownTests 4 }

upsTestDeepBatteryCalibration OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
           "The system is placed on battery to a discharge level,
            set by the manufacturer, sufficient to determine
            battery replacement and battery run-time with a high
            degree of confidence.  WARNING:  this test will leave
            the battery in a low charge state and will require
            time for recharging to a level sufficient to provide
            normal battery duration for the protected load."
    ::= { upsWellKnownTests 5 }

upsControl OBJECT IDENTIFIER ::= { MitsubishiUPS 8 }

upsShutdownType OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        output(1),
        system(2)
    }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "This object determines the nature of the action to be
            taken at the time when the countdown of the
            upsShutdownAfterDelay and upsRebootWithDuration
            objects reaches zero.

            Setting this object to output(1) indicates that
            shutdown requests should cause only the output of the
            UPS to turn off.  Setting this object to system(2)
            indicates that shutdown requests will cause the entire
            UPS system to turn off."
    ::= { upsControl 1 }

upsShutdownAfterDelay OBJECT-TYPE
    SYNTAX  INTEGER     -- UNITS seconds
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "Setting this object will shutdown (i.e., turn off)
            either the UPS output or the UPS system (as determined
            by the value of upsShutdownType at the time of
            shutdown) after the indicated number of seconds, or
            less if the UPS batteries become depleted. Setting
            this object to 0 will cause the shutdown to occur
            immediately.  Setting this object to -1 will abort the
            countdown.  If the system is already in the desired
            state at the time the countdown reaches 0, then
            nothing will happen.  That is, there is no additional
            action at that time if upsShutdownType = system and
            the system is already off.  Similarly, there is no
            additional action at that time if upsShutdownType =
            output and the output is already off.  When read,
            upsShutdownAfterDelay will return the number of
            seconds remaining until shutdown, or -1 if no shutdown
            countdown is in effect.  On some systems, if the agent
            is restarted while a shutdown countdown is in effect,
            the countdown may be aborted.  Sets to this object
            override any upsShutdownAfterDelay already in effect."
    ::= { upsControl 2 }

upsStartupAfterDelay OBJECT-TYPE
    SYNTAX  INTEGER     -- UNITS seconds
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "Setting this object will start the output after the
            indicated number of seconds, including starting the
            UPS, if necessary.  Setting this object to 0 will
            cause the startup to occur immediately.  Setting this
            object to -1 will abort the countdown.  If the output
            is already on at the time the countdown reaches 0,
            then nothing will happen.  Sets to this object
            override the effect of any upsStartupAfterDelay
            countdown or upsRebootWithDuration countdown in
            progress.  When read, upsStartupAfterDelay will return
            the number of seconds until startup, or -1 if no
            startup countdown is in effect.  If the countdown
            expires during a utility failure, the startup shall
            not occur until the utility power is restored.  On
            some systems, if the agent is restarted while a
            startup countdown is in effect, the countdown is
            aborted."
    ::= { upsControl 3 }

upsRebootWithDuration OBJECT-TYPE
    SYNTAX  INTEGER     -- UNITS seconds
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "Setting this object will immediately shutdown (i.e.,
            turn off) either the UPS output or the UPS system (as
            determined by the value of upsShutdownType at the time
            of shutdown) for a period equal to the indicated
            number of seconds, after which time the output will be
            started, including starting the UPS, if necessary.  If
            the number of seconds required to perform the request
            is greater than the requested duration, then the
            requested shutdown and startup cycle shall be
            performed in the minimum time possible, but in no case
            shall this require more than the requested duration
            plus 60 seconds.  When read, upsRebootWithDuration
            shall return the number of seconds remaining in the
            countdown, or -1 if no countdown is in progress.  If
            the startup should occur during a utility failure, the
            startup shall not occur until the utility power is
            restored."
    ::= { upsControl 4 }

upsAutoRestart OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        on(1),
        off(2)
    }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "Setting this object to 'on' will cause the UPS system
            to restart after a shutdown if the shutdown occurred
            during a power loss as a result of either a
            upsShutdownAfterDelay or an internal battery depleted
            condition.  Setting this object to 'off' will prevent
            the UPS system from restarting after a shutdown until
            an operator manually or remotely explicitly restarts
            it.  If the UPS is in a startup or reboot countdown,
            then the UPS will not restart until that delay has
            been satisfied."
    ::= { upsControl 5 }

upsConfig OBJECT IDENTIFIER ::= { MitsubishiUPS 9 }

upsConfigInputVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS RMS Volts
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the nominal input voltage (RMS Volts).  
            On those systems which support read-write access to this
            object, if there is an attempt to set this variable to
            a value that is not supported, the request must be
            rejected and the agent shall respond with an
            appropriate error message, i.e., badValue for SNMPv1,
            or inconsistentValue for SNMPv2."
    ::= { upsConfig 1 }

upsConfigInputFreq OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Hertz
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The nominal input frequency (0.1 Hertz).  On those systems
            which support read-write access to this object, if there is
            an attempt to set this variable to a value that is not
            supported, the request must be rejected and the agent
            shall respond with an appropriate error message, i.e.,
            badValue for SNMPv1, or inconsistentValue for SNMPv2."
    ::= { upsConfig 2 }

upsConfigOutputVoltage OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS RMS Volts
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the nominal output voltage (RMS Volts).  
            On those systems which support read-write access to this
            object, if there is an attempt to set this variable to
            a value that is not supported, the request must be
            rejected and the agent shall respond with an
            appropriate error message, i.e., badValue for SNMPv1,
            or inconsistentValue for SNMPv2."
    ::= { upsConfig 3 }

upsConfigOutputFreq OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS 0.1 Hertz
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The nominal output frequency (0.1 Hertz).  On those systems 
            which support read-write access to this object, if there is
            an attempt to set this variable to a value that is not
            supported, the request must be rejected and the agent
            shall respond with an appropriate error message, i.e.,
            badValue for SNMPv1, or inconsistentValue for SNMPv2."
    ::= { upsConfig 4 }

upsConfigOutputVA OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS Volt-Amps
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the nominal Volt-Amp rating (Volt-Amps)."
    ::= { upsConfig 5 }

upsConfigOutputPower OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS Watts
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
           "The magnitude of the nominal true power rating (watts)."
    ::= { upsConfig 6 }

upsConfigLowBattTime OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS minutes
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The value of upsEstimatedMinutesRemaining at which a
            lowBattery condition is declared.  For agents which
            support only discrete (discontinuous) values, then the
            agent shall round up to the next supported value.  If
            the requested value is larger than the largest
            supported value, then the largest supported value
            shall be selected."
    ::= { upsConfig 7 }

upsConfigAudibleStatus OBJECT-TYPE
    SYNTAX  INTEGER 
    {
        disabled(1),
        enabled(2),
        muted(3)
    }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The requested state of the audible alarm.  When in
            the disabled state, the audible alarm should never
            sound.  The enabled state is self-describing.  Setting
            this object to muted(3) when the audible alarm is
            sounding shall temporarily silence the alarm.  It will
            remain muted until it would normally stop sounding and
            the value returned for read operations during this
            period shall equal muted(3).  At the end of this
            period, the value shall revert to enabled(2).  Writes
            of the value muted(3) when the audible alarm is not
            sounding shall be accepted but otherwise shall have no
            effect."
    ::= { upsConfig 8 }

upsConfigLowVoltageTransferPoint OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS RMS Volts
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The minimum input line voltage (RMS Volts) allowed before 
            the UPS system transfers to battery backup."
    ::= { upsConfig 9 }

upsConfigHighVoltageTransferPoint OBJECT-TYPE
    SYNTAX  NonNegativeInteger  -- UNITS RMS Volts
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
           "The maximum line voltage (RMS Volts) allowed before the UPS
            system transfers to battery backup."
    ::= { upsConfig  10 }

-- UPS trap information group
upsTrapInfo OBJECT IDENTIFIER ::= { MitsubishiUPS 10 }

trapCode OBJECT-TYPE
	SYNTAX Unsigned32
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION
		"A number identifying the event for that last trap that was sent."
	::= { upsTrapInfo 1 }

trapDescription OBJECT-TYPE
	SYNTAX DisplayString (SIZE (0..63))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION
		"A string identifying the event for that last trap that was sent."
	::= { upsTrapInfo 2 }

-- UPS Traps
-- upsTraps OBJECT IDENTIFIER ::= { Tag 101 }

alarmCritical TRAP-TYPE
	ENTERPRISE MitsubishiUPS 
	VARIABLES  { trapCode, trapDescription }
	DESCRIPTION
		"Critical alarm."
	::= 1

alarmWarning TRAP-TYPE
	ENTERPRISE MitsubishiUPS
	VARIABLES  { trapCode, trapDescription }
	DESCRIPTION
		"Warning alarm."
	::= 2

alarmInformation TRAP-TYPE
	ENTERPRISE MitsubishiUPS 
	VARIABLES  { trapCode, trapDescription }
	DESCRIPTION
		"Information alarm."
	::= 3

upsAlarmCleared TRAP-TYPE
	ENTERPRISE MitsubishiUPS
	VARIABLES  { trapCode, trapDescription }
	DESCRIPTION
		"Alarm cleared."
	::= 4

upsTrapInitialization TRAP-TYPE
	ENTERPRISE  MitsubishiUPS 
	VARIABLES   { upsIdentName }
	DESCRIPTION
		"This trap is sent each time a NetCom device is initialized."
	::= 5

END