1085 lines
37 KiB
Plaintext
1085 lines
37 KiB
Plaintext
FRAME-RELAY-DTE-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE, Counter32,
|
|
Integer32, NOTIFICATION-TYPE FROM SNMPv2-SMI
|
|
TEXTUAL-CONVENTION, RowStatus, TimeStamp FROM SNMPv2-TC
|
|
MODULE-COMPLIANCE, OBJECT-GROUP,
|
|
NOTIFICATION-GROUP FROM SNMPv2-CONF
|
|
transmission FROM RFC1213-MIB
|
|
InterfaceIndex FROM IF-MIB;
|
|
|
|
-- Frame Relay DTE MIB
|
|
|
|
frameRelayDTE MODULE-IDENTITY
|
|
LAST-UPDATED "9705010229Z" -- Thu May 1 02:29:46 PDT 1997
|
|
ORGANIZATION "IETF IPLPDN Working Group"
|
|
CONTACT-INFO
|
|
" Caralyn Brown
|
|
Postal: Cadia Networks, Inc.
|
|
1 Corporate Drive
|
|
Andover, Massachusetts 01810
|
|
Tel: +1 508 689 2400 x133
|
|
E-Mail: cbrown@cadia.com
|
|
|
|
Fred Baker
|
|
Postal: Cisco Systems
|
|
519 Lado Drive
|
|
Santa Barbara, California 93111
|
|
Tel: +1 408 526 425
|
|
E-Mail: fred@cisco.com"
|
|
DESCRIPTION
|
|
"The MIB module to describe the use of a Frame Relay
|
|
interface by a DTE."
|
|
REVISION "9705010229Z" -- Thu May 1 02:29:46 PDT 1997
|
|
DESCRIPTION
|
|
"Converted from SMIv1 to SMIv2. (Thus, indices are
|
|
read-only rather than being not-accessible.) Added
|
|
objects and made clarifications based on implementation
|
|
experience."
|
|
|
|
REVISION "9204010000Z"
|
|
DESCRIPTION
|
|
"Published as RFC 1315, the initial version of this MIB
|
|
module."
|
|
::= { transmission 32 }
|
|
|
|
|
|
--
|
|
-- the range of a Data Link Connection Identifier
|
|
--
|
|
DLCI ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The range of DLCI values. Note that this varies by
|
|
interface configuration; normally, interfaces may use
|
|
0..1023, but may be configured to use ranges as large
|
|
as 0..2^23."
|
|
SYNTAX Integer32(0..8388607)
|
|
|
|
|
|
|
|
--
|
|
|
|
-- Data Link Connection Management Interface
|
|
|
|
-- The variables that configure the DLC Management Interface.
|
|
|
|
frDlcmiTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF FrDlcmiEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Parameters for the Data Link Connection Management
|
|
Interface for the frame relay service on this
|
|
interface."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Annex D"
|
|
::= { frameRelayDTE 1 }
|
|
|
|
frDlcmiEntry OBJECT-TYPE
|
|
SYNTAX FrDlcmiEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Parameters for a particular Data Link Connection
|
|
Management Interface."
|
|
INDEX { frDlcmiIfIndex }
|
|
::= { frDlcmiTable 1 }
|
|
|
|
|
|
|
|
|
|
|
|
FrDlcmiEntry ::=
|
|
SEQUENCE {
|
|
frDlcmiIfIndex InterfaceIndex,
|
|
frDlcmiState INTEGER,
|
|
frDlcmiAddress INTEGER,
|
|
frDlcmiAddressLen INTEGER,
|
|
frDlcmiPollingInterval Integer32,
|
|
frDlcmiFullEnquiryInterval Integer32,
|
|
frDlcmiErrorThreshold Integer32,
|
|
frDlcmiMonitoredEvents Integer32,
|
|
frDlcmiMaxSupportedVCs DLCI,
|
|
frDlcmiMulticast INTEGER,
|
|
frDlcmiStatus INTEGER,
|
|
frDlcmiRowStatus RowStatus
|
|
}
|
|
|
|
|
|
frDlcmiIfIndex OBJECT-TYPE
|
|
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The ifIndex value of the corresponding ifEntry."
|
|
::= { frDlcmiEntry 1 }
|
|
|
|
|
|
frDlcmiState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
noLmiConfigured (1),
|
|
lmiRev1 (2),
|
|
ansiT1617D (3), -- ANSI T1.617 Annex D
|
|
ansiT1617B (4), -- ANSI T1.617 Annex B
|
|
itut933A (5), -- CCITT Q933 Annex A
|
|
ansiT1617D1994 (6) -- ANSI T1.617a-1994 Annex D
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable states which Data Link Connection
|
|
Management scheme is active (and by implication, what
|
|
DLCI it uses) on the Frame Relay interface."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, American
|
|
National Standard T1.617a-1994, ITU-T Recommendation
|
|
Q.933 (03/93)."
|
|
|
|
::= { frDlcmiEntry 2 }
|
|
|
|
|
|
frDlcmiAddress OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
q921 (1), -- 13 bit DLCI
|
|
q922March90 (2), -- 11 bit DLCI
|
|
q922November90 (3), -- 10 bit DLCI
|
|
q922 (4) -- Final Standard
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable states which address format is in use on
|
|
the Frame Relay interface."
|
|
::= { frDlcmiEntry 3 }
|
|
|
|
|
|
frDlcmiAddressLen OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
twoOctets (2),
|
|
threeOctets (3),
|
|
fourOctets (4)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable states the address length in octets. In
|
|
the case of Q922 format, the length indicates the
|
|
entire length of the address including the control
|
|
portion."
|
|
::= { frDlcmiEntry 4 }
|
|
|
|
|
|
frDlcmiPollingInterval OBJECT-TYPE
|
|
SYNTAX Integer32 (5..30)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the number of seconds between successive
|
|
status enquiry messages."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section D.7
|
|
Timer T391."
|
|
DEFVAL { 10 }
|
|
::= { frDlcmiEntry 5 }
|
|
|
|
|
|
frDlcmiFullEnquiryInterval OBJECT-TYPE
|
|
SYNTAX Integer32 (1..255)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of status enquiry intervals that pass before
|
|
issuance of a full status enquiry message."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section D.7
|
|
Counter N391."
|
|
DEFVAL { 6 }
|
|
::= { frDlcmiEntry 6 }
|
|
|
|
|
|
frDlcmiErrorThreshold OBJECT-TYPE
|
|
SYNTAX Integer32 (1..10)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the maximum number of unanswered Status
|
|
Enquiries the equipment shall accept before declaring
|
|
the interface down."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section D.5.1
|
|
Counter N392."
|
|
DEFVAL { 3 }
|
|
::= { frDlcmiEntry 7 }
|
|
|
|
|
|
frDlcmiMonitoredEvents OBJECT-TYPE
|
|
SYNTAX Integer32 (1..10)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is the number of status polling intervals over
|
|
which the error threshold is counted. For example, if
|
|
within 'MonitoredEvents' number of events the station
|
|
receives 'ErrorThreshold' number of errors, the
|
|
interface is marked as down."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section D.5.2
|
|
Counter N393."
|
|
DEFVAL { 4 }
|
|
::= { frDlcmiEntry 8 }
|
|
|
|
|
|
|
|
|
|
frDlcmiMaxSupportedVCs OBJECT-TYPE
|
|
SYNTAX DLCI
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The maximum number of Virtual Circuits allowed for
|
|
this interface. Usually dictated by the Frame Relay
|
|
network.
|
|
|
|
In response to a SET, if a value less than zero or
|
|
higher than the agent's maximal capability is
|
|
configured, the agent should respond badValue"
|
|
::= { frDlcmiEntry 9 }
|
|
|
|
|
|
frDlcmiMulticast OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
nonBroadcast (1),
|
|
broadcast (2)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This indicates whether the Frame Relay interface is
|
|
using a multicast service."
|
|
::= { frDlcmiEntry 10 }
|
|
|
|
|
|
|
|
frDlcmiStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
running (1), -- init complete, system running
|
|
fault (2), -- error threshold exceeded
|
|
initializing (3) -- system start up
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This indicates the status of the Frame Relay interface
|
|
as determined by the performance of the dlcmi. If no
|
|
dlcmi is running, the Frame Relay interface will stay
|
|
in the running state indefinitely."
|
|
::= { frDlcmiEntry 11 }
|
|
|
|
|
|
|
|
|
|
|
|
frDlcmiRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"SNMP Version 2 Row Status Variable. Writable objects
|
|
in the table may be written in any RowStatus state."
|
|
::= { frDlcmiEntry 12 }
|
|
|
|
|
|
--
|
|
-- A Frame Relay service is a multiplexing service. Data
|
|
-- Link Connection Identifiers enumerate virtual circuits
|
|
-- (permanent or dynamic) which are layered onto the underlying
|
|
-- circuit, represented by ifEntry. Therefore, each of the entries
|
|
-- in the Standard MIB's Interface Table with an IfType of
|
|
-- Frame Relay represents a Q.922 interface. Zero or more
|
|
-- virtual circuits are layered onto this interface and provide
|
|
-- interconnection with various remote destinations.
|
|
-- Each such virtual circuit is represented by an entry in the
|
|
-- circuit table. The management virtual circuit (i.e. DLCI 0)
|
|
-- is a virtual circuit by this definition and will be represented
|
|
-- with an entry in the circuit table.
|
|
|
|
-- Circuit Table
|
|
|
|
-- The table describing the use of the DLCIs attached to
|
|
-- each Frame Relay Interface.
|
|
|
|
frCircuitTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF FrCircuitEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table containing information about specific Data
|
|
Link Connections (DLC) or virtual circuits."
|
|
::= { frameRelayDTE 2 }
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
frCircuitEntry OBJECT-TYPE
|
|
SYNTAX FrCircuitEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The information regarding a single Data Link
|
|
Connection. Discontinuities in the counters contained
|
|
in this table are indicated by the value in
|
|
frCircuitCreationTime."
|
|
INDEX { frCircuitIfIndex, frCircuitDlci }
|
|
::= { frCircuitTable 1 }
|
|
|
|
|
|
FrCircuitEntry ::=
|
|
SEQUENCE {
|
|
frCircuitIfIndex InterfaceIndex,
|
|
frCircuitDlci DLCI,
|
|
frCircuitState INTEGER,
|
|
frCircuitReceivedFECNs Counter32,
|
|
frCircuitReceivedBECNs Counter32,
|
|
frCircuitSentFrames Counter32,
|
|
frCircuitSentOctets Counter32,
|
|
frCircuitReceivedFrames Counter32,
|
|
frCircuitReceivedOctets Counter32,
|
|
frCircuitCreationTime TimeStamp,
|
|
frCircuitLastTimeChange TimeStamp,
|
|
frCircuitCommittedBurst Integer32,
|
|
frCircuitExcessBurst Integer32,
|
|
frCircuitThroughput Integer32,
|
|
frCircuitMulticast INTEGER,
|
|
frCircuitType INTEGER,
|
|
frCircuitDiscards Counter32,
|
|
frCircuitReceivedDEs Counter32,
|
|
frCircuitSentDEs Counter32,
|
|
frCircuitLogicalIfIndex InterfaceIndex,
|
|
frCircuitRowStatus RowStatus
|
|
}
|
|
|
|
|
|
frCircuitIfIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The ifIndex Value of the ifEntry this virtual circuit
|
|
is layered onto."
|
|
::= { frCircuitEntry 1 }
|
|
|
|
|
|
frCircuitDlci OBJECT-TYPE
|
|
SYNTAX DLCI
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Data Link Connection Identifier for this virtual
|
|
circuit."
|
|
REFERENCE
|
|
"American National Standard T1.618-1991, Section 3.3.6"
|
|
::= { frCircuitEntry 2 }
|
|
|
|
|
|
frCircuitState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
|
|
invalid (1),
|
|
active (2),
|
|
inactive (3)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates whether the particular virtual circuit is
|
|
operational. In the absence of a Data Link Connection
|
|
Management Interface, virtual circuit entries (rows)
|
|
may be created by setting virtual circuit state to
|
|
'active', or deleted by changing Circuit state to
|
|
'invalid'.
|
|
|
|
Whether or not the row actually disappears is left to
|
|
the implementation, so this object may actually read as
|
|
'invalid' for some arbitrary length of time. It is
|
|
also legal to set the state of a virtual circuit to
|
|
'inactive' to temporarily disable a given circuit.
|
|
|
|
The use of 'invalid' is deprecated in this SNMP Version
|
|
2 MIB, in favor of frCircuitRowStatus."
|
|
DEFVAL { active }
|
|
::= { frCircuitEntry 3 }
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
frCircuitReceivedFECNs OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of frames received from the network indicating
|
|
forward congestion since the virtual circuit was
|
|
created. This occurs when the remote DTE sets the FECN
|
|
flag, or when a switch in the network enqueues the
|
|
frame to a trunk whose transmission queue is
|
|
congested."
|
|
REFERENCE
|
|
"American National Standard T1.618-1991, Section 3.3.3"
|
|
::= { frCircuitEntry 4 }
|
|
|
|
|
|
frCircuitReceivedBECNs OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
|
|
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of frames received from the network indicating
|
|
backward congestion since the virtual circuit was
|
|
created. This occurs when the remote DTE sets the BECN
|
|
flag, or when a switch in the network receives the
|
|
frame from a trunk whose transmission queue is
|
|
congested."
|
|
REFERENCE
|
|
"American National Standard T1.618-1991, Section 3.3.4"
|
|
::= { frCircuitEntry 5 }
|
|
|
|
|
|
frCircuitSentFrames OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of frames sent from this virtual circuit
|
|
since it was created."
|
|
::= { frCircuitEntry 6 }
|
|
|
|
|
|
frCircuitSentOctets OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of octets sent from this virtual circuit
|
|
since it was created. Octets counted are the full
|
|
frame relay header and the payload, but do not include
|
|
the flag characters or CRC."
|
|
::= { frCircuitEntry 7 }
|
|
|
|
|
|
frCircuitReceivedFrames OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of frames received over this virtual circuit
|
|
since it was created."
|
|
::= { frCircuitEntry 8 }
|
|
|
|
|
|
frCircuitReceivedOctets OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of octets received over this virtual circuit
|
|
since it was created. Octets counted include the full
|
|
frame relay header, but do not include the flag
|
|
characters or the CRC."
|
|
::= { frCircuitEntry 9 }
|
|
|
|
|
|
frCircuitCreationTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime when the virtual circuit was
|
|
created, whether by the Data Link Connection Management
|
|
Interface or by a SetRequest."
|
|
::= { frCircuitEntry 10 }
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
frCircuitLastTimeChange OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime when last there was a change in
|
|
the virtual circuit state"
|
|
::= { frCircuitEntry 11 }
|
|
|
|
|
|
frCircuitCommittedBurst OBJECT-TYPE
|
|
SYNTAX Integer32(0..2147483647)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the maximum amount of data, in
|
|
bits, that the network agrees to transfer under normal
|
|
conditions, during the measurement interval."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section
|
|
6.5.19"
|
|
DEFVAL { 0 } -- the default indicates no commitment
|
|
::= { frCircuitEntry 12 }
|
|
|
|
|
|
frCircuitExcessBurst OBJECT-TYPE
|
|
SYNTAX Integer32(0..2147483647)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the maximum amount of
|
|
uncommitted data bits that the network will attempt to
|
|
deliver over the measurement interval.
|
|
|
|
By default, if not configured when creating the entry,
|
|
the Excess Information Burst Size is set to the value
|
|
of ifSpeed."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section
|
|
6.5.19"
|
|
::= { frCircuitEntry 13 }
|
|
|
|
|
|
frCircuitThroughput OBJECT-TYPE
|
|
SYNTAX Integer32(0..2147483647)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Throughput is the average number of 'Frame Relay
|
|
Information Field' bits transferred per second across a
|
|
user network interface in one direction, measured over
|
|
the measurement interval.
|
|
|
|
If the configured committed burst rate and throughput
|
|
are both non-zero, the measurement interval, T, is
|
|
T=frCircuitCommittedBurst/frCircuitThroughput.
|
|
|
|
If the configured committed burst rate and throughput
|
|
are both zero, the measurement interval, T, is
|
|
T=frCircuitExcessBurst/ifSpeed."
|
|
REFERENCE
|
|
"American National Standard T1.617-1991, Section
|
|
6.5.19"
|
|
DEFVAL {0} -- the default value of Throughput is
|
|
-- "no commitment".
|
|
::= { frCircuitEntry 14 }
|
|
|
|
|
|
frCircuitMulticast OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unicast (1),
|
|
oneWay (2),
|
|
twoWay (3),
|
|
nWay (4)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This indicates whether this VC is used as a unicast VC
|
|
(i.e. not multicast) or the type of multicast service
|
|
subscribed to"
|
|
REFERENCE
|
|
"Frame Relay PVC Multicast Service and Protocol
|
|
Description Implementation: FRF.7 Frame Relay Forum
|
|
Technical Committe October 21, 1994"
|
|
DEFVAL {unicast}
|
|
-- the default value of frCircuitMulticast is
|
|
-- "unicast" (not a multicast VC).
|
|
::= { frCircuitEntry 15 }
|
|
|
|
|
|
frCircuitType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
static (1),
|
|
dynamic (2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indication of whether the VC was manually created
|
|
(static), or dynamically created (dynamic) via the data
|
|
link control management interface."
|
|
::= { frCircuitEntry 16 }
|
|
|
|
|
|
frCircuitDiscards OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of inbound frames dropped because of format
|
|
errors, or because the VC is inactive."
|
|
::= { frCircuitEntry 17 }
|
|
|
|
|
|
frCircuitReceivedDEs OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of frames received from the network indicating
|
|
that they were eligible for discard since the virtual
|
|
circuit was created. This occurs when the remote DTE
|
|
sets the DE flag, or when in remote DTE's switch
|
|
detects that the frame was received as Excess Burst
|
|
data."
|
|
REFERENCE
|
|
"American National Standard T1.618-1991, Section 3.3.4"
|
|
::= { frCircuitEntry 18 }
|
|
|
|
|
|
frCircuitSentDEs OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Number of frames sent to the network indicating that
|
|
they were eligible for discard since the virtual
|
|
circuit was created. This occurs when the local DTE
|
|
sets the DE flag, indicating that during Network
|
|
congestion situations those frames should be discarded
|
|
in preference of other frames sent without the DE bit
|
|
set."
|
|
REFERENCE
|
|
"American National Standard T1.618-1991, Section
|
|
3.3.4"
|
|
::= { frCircuitEntry 19 }
|
|
|
|
frCircuitLogicalIfIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Normally the same value as frDlcmiIfIndex, but
|
|
different when an implementation associates a virtual
|
|
ifEntry with a DLC or set of DLCs in order to associate
|
|
higher layer objects such as the ipAddrEntry with a
|
|
subset of the virtual circuits on a Frame Relay
|
|
interface. The type of such ifEntries is defined by the
|
|
higher layer object; for example, if PPP/Frame Relay is
|
|
implemented, the ifType of this ifEntry would be PPP.
|
|
If it is not so defined, as would be the case with an
|
|
ipAddrEntry, it should be of type Other."
|
|
::= { frCircuitEntry 20 }
|
|
|
|
frCircuitRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
destroy an existing row in the manner described in the
|
|
definition of the RowStatus textual convention.
|
|
Writable objects in the table may be written in any
|
|
RowStatus state."
|
|
::= { frCircuitEntry 21 }
|
|
|
|
|
|
--
|
|
-- Error Table
|
|
|
|
-- The table describing errors encountered on each Frame
|
|
-- Relay Interface.
|
|
|
|
frErrTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF FrErrEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table containing information about Errors on the
|
|
Frame Relay interface. Discontinuities in the counters
|
|
contained in this table are the same as apply to the
|
|
ifEntry associated with the Interface."
|
|
::= { frameRelayDTE 3 }
|
|
|
|
frErrEntry OBJECT-TYPE
|
|
SYNTAX FrErrEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The error information for a single frame relay
|
|
interface."
|
|
INDEX { frErrIfIndex }
|
|
::= { frErrTable 1 }
|
|
|
|
|
|
FrErrEntry ::=
|
|
SEQUENCE {
|
|
frErrIfIndex InterfaceIndex,
|
|
frErrType INTEGER,
|
|
frErrData OCTET STRING,
|
|
frErrTime TimeStamp,
|
|
frErrFaults Counter32,
|
|
frErrFaultTime TimeStamp
|
|
}
|
|
|
|
|
|
frErrIfIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The ifIndex Value of the corresponding ifEntry."
|
|
::= { frErrEntry 1 }
|
|
|
|
|
|
frErrType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknownError(1),
|
|
receiveShort(2),
|
|
receiveLong(3),
|
|
illegalAddress(4),
|
|
unknownAddress(5),
|
|
dlcmiProtoErr(6),
|
|
dlcmiUnknownIE(7),
|
|
dlcmiSequenceErr(8),
|
|
dlcmiUnknownRpt(9),
|
|
noErrorSinceReset(10)
|
|
}
|
|
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The type of error that was last seen on this interface:
|
|
|
|
receiveShort: frame was not long enough to allow
|
|
demultiplexing - the address field was incomplete,
|
|
or for virtual circuits using Multiprotocol over
|
|
Frame Relay, the protocol identifier was missing
|
|
or incomplete.
|
|
|
|
receiveLong: frame exceeded maximum length configured for this
|
|
interface.
|
|
|
|
illegalAddress: address field did not match configured format.
|
|
|
|
unknownAddress: frame received on a virtual circuit which was not
|
|
active or administratively disabled.
|
|
|
|
dlcmiProtoErr: unspecified error occurred when attempting to
|
|
interpret link maintenance frame.
|
|
|
|
dlcmiUnknownIE: link maintenance frame contained an Information
|
|
Element type which is not valid for the
|
|
configured link maintenance protocol.
|
|
|
|
dlcmiSequenceErr: link maintenance frame contained a sequence
|
|
number other than the expected value.
|
|
|
|
dlcmiUnknownRpt: link maintenance frame contained a Report Type
|
|
Information Element whose value was not valid
|
|
for the configured link maintenance protocol.
|
|
|
|
noErrorSinceReset: no errors have been detected since the last
|
|
cold start or warm start."
|
|
::= { frErrEntry 2 }
|
|
|
|
|
|
frErrData OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE(1..1600))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An octet string containing as much of the error packet
|
|
as possible. As a minimum, it must contain the Q.922
|
|
Address or as much as was delivered. It is desirable
|
|
to include all header and demultiplexing information."
|
|
::= { frErrEntry 3 }
|
|
|
|
|
|
frErrTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime at which the error was
|
|
detected."
|
|
::= { frErrEntry 4 }
|
|
|
|
|
|
frErrFaults OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of times the interface has gone down since
|
|
it was initialized."
|
|
::= { frErrEntry 5 }
|
|
|
|
|
|
frErrFaultTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime at the time when the interface
|
|
was taken down due to excessive errors. Excessive
|
|
errors is defined as the time when a DLCMI exceeds the
|
|
frDlcmiErrorThreshold number of errors within
|
|
frDlcmiMonitoredEvents. See FrDlcmiEntry for further
|
|
details."
|
|
::= { frErrEntry 6 }
|
|
|
|
|
|
--
|
|
|
|
-- Frame Relay Trap Control
|
|
|
|
frameRelayTrapControl OBJECT IDENTIFIER ::= { frameRelayDTE 4 }
|
|
|
|
-- the following highly unusual OID is as it is for compatibility
|
|
-- with RFC 1315, the SNMP V1 predecessor of this document.
|
|
frameRelayTraps OBJECT IDENTIFIER ::= { frameRelayDTE 0 }
|
|
|
|
|
|
|
|
frTrapState OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates whether the system produces
|
|
the frDLCIStatusChange trap."
|
|
DEFVAL { disabled }
|
|
::= { frameRelayTrapControl 1 }
|
|
|
|
frTrapMaxRate OBJECT-TYPE
|
|
SYNTAX Integer32 (0..3600000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the number of milliseconds
|
|
that must elapse between trap emissions. If events
|
|
occur more rapidly, the impementation may simply fail
|
|
to trap, or may queue traps until an appropriate time."
|
|
DEFVAL { 0 } -- no minimum elapsed period is specified
|
|
::= { frameRelayTrapControl 2 }
|
|
|
|
|
|
|
|
-- Data Link Connection Management Interface Related Traps
|
|
|
|
frDLCIStatusChange NOTIFICATION-TYPE
|
|
OBJECTS { frCircuitState }
|
|
STATUS current
|
|
|
|
|
|
DESCRIPTION
|
|
"This trap indicates that the indicated Virtual Circuit
|
|
has changed state. It has either been created or
|
|
invalidated, or has toggled between the active and
|
|
inactive states. If, however, the reason for the state
|
|
change is due to the DLCMI going down, per-DLCI traps
|
|
should not be generated."
|
|
::= { frameRelayTraps 1 }
|
|
-- conformance information
|
|
|
|
frConformance OBJECT IDENTIFIER ::= { frameRelayDTE 6 }
|
|
|
|
frGroups OBJECT IDENTIFIER ::= { frConformance 1 }
|
|
frCompliances OBJECT IDENTIFIER ::= { frConformance 2 }
|
|
|
|
-- compliance statements
|
|
|
|
frCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement "
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { frPortGroup, frCircuitGroup }
|
|
|
|
GROUP frErrGroup
|
|
DESCRIPTION
|
|
"This optional group is used for debugging Frame Relay
|
|
Systems."
|
|
|
|
GROUP frTrapGroup
|
|
DESCRIPTION
|
|
"This optional group is used for the management of
|
|
asynchronous notifications by Frame Relay Systems."
|
|
|
|
GROUP frNotificationGroup
|
|
DESCRIPTION
|
|
"This optional group defines the asynchronous
|
|
notifications generated by Frame Relay Systems."
|
|
|
|
OBJECT frDlcmiRowStatus
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Row creation is not required for the frDlcmiTable."
|
|
|
|
OBJECT frCircuitRowStatus
|
|
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Row creation is not required for the frCircuitTable."
|
|
|
|
::= { frCompliances 1 }
|
|
|
|
frCompliance0 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for objects and the trap
|
|
defined in RFC 1315."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { frPortGroup0, frCircuitGroup0 }
|
|
|
|
GROUP frErrGroup0
|
|
DESCRIPTION
|
|
"This optional group is used for debugging Frame Relay
|
|
Systems."
|
|
|
|
GROUP frTrapGroup0
|
|
DESCRIPTION
|
|
"This optional group is used for the management of
|
|
asynchronous notifications by Frame Relay Systems."
|
|
|
|
GROUP frNotificationGroup
|
|
DESCRIPTION
|
|
"This optional group defines the asynchronous
|
|
notifications generated by Frame Relay Systems."
|
|
|
|
::= { frCompliances 2 }
|
|
|
|
-- units of conformance
|
|
|
|
frPortGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
frDlcmiIfIndex, frDlcmiState, frDlcmiAddress,
|
|
frDlcmiAddressLen, frDlcmiPollingInterval,
|
|
frDlcmiFullEnquiryInterval, frDlcmiErrorThreshold,
|
|
frDlcmiMonitoredEvents, frDlcmiMaxSupportedVCs,
|
|
frDlcmiMulticast, frDlcmiStatus, frDlcmiRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control the Link Management
|
|
Interface for a Frame Relay Interface as well as
|
|
maintain the error statistics on this interface."
|
|
::= { frGroups 1 }
|
|
|
|
frCircuitGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
frCircuitIfIndex, frCircuitDlci, frCircuitState,
|
|
frCircuitReceivedFECNs, frCircuitReceivedBECNs,
|
|
frCircuitSentFrames, frCircuitSentOctets,
|
|
frCircuitReceivedFrames, frCircuitReceivedOctets,
|
|
frCircuitCreationTime, frCircuitLastTimeChange,
|
|
frCircuitCommittedBurst, frCircuitExcessBurst,
|
|
frCircuitThroughput, frCircuitMulticast,
|
|
frCircuitType, frCircuitDiscards,
|
|
frCircuitReceivedDEs, frCircuitSentDEs,
|
|
frCircuitLogicalIfIndex, frCircuitRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control the Virtual Circuits
|
|
layered onto a Frame Relay Interface."
|
|
::= { frGroups 2 }
|
|
|
|
frTrapGroup OBJECT-GROUP
|
|
OBJECTS { frTrapState, frTrapMaxRate }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control a Frame Relay
|
|
Interface's notification messages."
|
|
::= { frGroups 3 }
|
|
|
|
frErrGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
frErrIfIndex, frErrType, frErrData, frErrTime,
|
|
frErrFaults, frErrFaultTime
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects designed to assist in debugging Frame Relay
|
|
Interfaces."
|
|
::= { frGroups 4 }
|
|
|
|
frNotificationGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS { frDLCIStatusChange }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Traps which may be used to enhance event driven
|
|
management of the interface."
|
|
::= { frGroups 5 }
|
|
|
|
frPortGroup0 OBJECT-GROUP
|
|
OBJECTS {
|
|
frDlcmiIfIndex, frDlcmiState, frDlcmiAddress,
|
|
frDlcmiAddressLen, frDlcmiPollingInterval,
|
|
frDlcmiFullEnquiryInterval, frDlcmiErrorThreshold,
|
|
frDlcmiMonitoredEvents, frDlcmiMaxSupportedVCs,
|
|
frDlcmiMulticast
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control the Link Management
|
|
Interface for a Frame Relay Interface as well as
|
|
maintain the error statistics on this interface from
|
|
RFC 1315."
|
|
::= { frGroups 6 }
|
|
|
|
frCircuitGroup0 OBJECT-GROUP
|
|
OBJECTS {
|
|
frCircuitIfIndex, frCircuitDlci, frCircuitState,
|
|
frCircuitReceivedFECNs, frCircuitReceivedBECNs,
|
|
frCircuitSentFrames, frCircuitSentOctets,
|
|
frCircuitReceivedFrames, frCircuitReceivedOctets,
|
|
frCircuitCreationTime, frCircuitLastTimeChange,
|
|
frCircuitCommittedBurst, frCircuitExcessBurst,
|
|
frCircuitThroughput
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control the Virtual Circuits
|
|
layered onto a Frame Relay Interface from RFC 1315."
|
|
::= { frGroups 7 }
|
|
|
|
frErrGroup0 OBJECT-GROUP
|
|
OBJECTS {
|
|
frErrIfIndex, frErrType, frErrData, frErrTime
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Objects designed to assist in debugging Frame Relay
|
|
Interfaces from RFC 1315."
|
|
::= { frGroups 8 }
|
|
|
|
|
|
frTrapGroup0 OBJECT-GROUP
|
|
OBJECTS { frTrapState }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The objects necessary to control a Frame Relay
|
|
Interface's notification messages from RFC 1315."
|
|
::= { frGroups 9 }
|
|
|
|
END
|