2843 lines
116 KiB
Plaintext
2843 lines
116 KiB
Plaintext
-- HP Enterprise Switch Configuration MIB
|
|
|
|
|
|
CONFIG-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
IpAddress
|
|
FROM RFC1155-SMI
|
|
OBJECT-TYPE
|
|
FROM RFC-1212
|
|
TRAP-TYPE
|
|
FROM RFC-1215
|
|
dot1dStpPortState, dot1dStpPortDesignatedBridge,
|
|
dot1dStpPortDesignatedPort
|
|
FROM BRIDGE-MIB -- RFC-1493
|
|
DisplayString, RowStatus, MacAddress, TimeStamp
|
|
FROM SNMPv2-TC
|
|
HpSwitchPortType, ConfigStatus
|
|
FROM HP-ICF-TC
|
|
hpSwitch
|
|
FROM HP-ICF-OID
|
|
InetAddressType, InetAddress
|
|
FROM INET-ADDRESS-MIB;
|
|
|
|
-- type.
|
|
Timeout ::= INTEGER -- a STP timer in units of 1/100 seconds
|
|
|
|
-- Icf Switch Specific
|
|
hpConfig OBJECT IDENTIFIER ::= { hpSwitch 7 }
|
|
|
|
VlanID ::= INTEGER (1..65535)
|
|
|
|
|
|
-- ###########################################################
|
|
-- the hpConfig Group
|
|
|
|
-- This group contains switch configuration related variables.
|
|
-- ###########################################################
|
|
|
|
hpSwitchConfig OBJECT IDENTIFIER ::= { hpConfig 1 }
|
|
|
|
hpSwitchSystemConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 1 }
|
|
|
|
hpSwitchAutoReboot OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
yes(1),
|
|
no(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "If the value of this variable was set to yes(1),
|
|
booting will conditionally enable all application
|
|
modules-the spanning tree, IP and IPX etc.. Otherwise
|
|
every application module must be manually enabled
|
|
through Network Control Language Interpreter's ENABLE
|
|
command."
|
|
::= { hpSwitchSystemConfig 1 }
|
|
|
|
hpSwitchTimeZone OBJECT-TYPE
|
|
SYNTAX INTEGER (-720..840)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of minutes to the east of Greenwich Mean
|
|
Time(GMT). For a location west of GMT, use a negative
|
|
integer."
|
|
::= { hpSwitchSystemConfig 2 }
|
|
|
|
hpSwitchDaylightTimeRule OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
alaska(2),
|
|
canadaAndContinentalUS(3),
|
|
middleEuropeAndPortugal(4),
|
|
southernHemisphere(5),
|
|
westernEurop(6),
|
|
userDefined(7)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The daylight savings time rule for use by the
|
|
Internet's RFC 868 Time protocol."
|
|
::= { hpSwitchSystemConfig 3 }
|
|
|
|
hpSwitchDaylightBeginningMonth OBJECT-TYPE
|
|
SYNTAX INTEGER (1..12)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The month that daylight saving time starts if
|
|
DaylightTimeRule is set to userDefined."
|
|
::= { hpSwitchSystemConfig 4 }
|
|
|
|
hpSwitchDaylightBeginningDay OBJECT-TYPE
|
|
SYNTAX INTEGER (1..31)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The day of the month that daylight saving time
|
|
starts if DaylightTimeRule is set to userDefined."
|
|
::= { hpSwitchSystemConfig 5 }
|
|
|
|
hpSwitchDaylightEndingMonth OBJECT-TYPE
|
|
SYNTAX INTEGER (1..12)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The month that daylight saving time ends if
|
|
DaylightTimeRule is set to userDefined."
|
|
::= { hpSwitchSystemConfig 6 }
|
|
|
|
hpSwitchDaylightEndingDay OBJECT-TYPE
|
|
SYNTAX INTEGER (1..31)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The day of the month that daylight saving time emds
|
|
if DaylightTimeRule is set to userDefined."
|
|
::= { hpSwitchSystemConfig 7 }
|
|
|
|
hpSwitchSystemConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The configuration status of this group of objects.
|
|
If one or more variables in this group were
|
|
reconfigurated since last reboot and required reboot
|
|
to take effect, the value of this variable will be
|
|
set to notInService."
|
|
::= { hpSwitchSystemConfig 8 }
|
|
|
|
hpSwitchSystemPortLEDMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
link-activity(1),
|
|
link-only(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The mode of the port LED can be either link/activity
|
|
(link for 3 seconds then activity thereafter) or
|
|
link-only."
|
|
::= { hpSwitchSystemConfig 9 }
|
|
|
|
hpSwitchControlUnknownIPMulticast OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "When enabled along with IGMP, any IP Multicast packets
|
|
that are not already controlled by IGMP will be
|
|
restricted to ports that have detected a multicast
|
|
router or ports configured to always forward IP
|
|
multicast. When set to disabled or when IGMP is
|
|
disabled, the unknown IP Multicast packets will be
|
|
flooded out all ports in the VLAN"
|
|
::= { hpSwitchSystemConfig 10 }
|
|
|
|
hpSwitchIgmpDelayedGroupFlushTimer OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This feature is disabled by default, which is indicated
|
|
by a timer value of 0 seconds. When IGMP is enabled and
|
|
the value of the Delayed Group Flush Timer is not zero,
|
|
traffic filters for any previously-joined IGMP groups
|
|
which no longer have active members will persist for
|
|
the number of seconds indicated by the timer. This has
|
|
the effect of dropping any additional unjoined traffic
|
|
for an empty group until the Delayed Group Flush Timer
|
|
expires, at which time the traffic filter is then
|
|
removed."
|
|
::= { hpSwitchSystemConfig 11 }
|
|
|
|
hpSwitchMaxFrameSize OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This is the value of the global jumbos max-frame-size
|
|
supported by the switch. The default value for this is
|
|
set to 9216, in order to make it compatible with
|
|
previous versions of software. This configuration does
|
|
not take a reboot to take effect."
|
|
::= { hpSwitchSystemConfig 12 }
|
|
|
|
hpSwitchIpMTU OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This is the value of the global jumbos IP MTU or L3 MTU
|
|
supported by the switch. The default value for this is
|
|
set to 9198, in order to make it compatible with
|
|
previous versions of software. This configuration does
|
|
not take a reboot to take effect."
|
|
::= { hpSwitchSystemConfig 13 }
|
|
|
|
|
|
hpSwitchConsoleConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 2 }
|
|
|
|
hpSwitchTelnetAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "The status of the console telnet operation."
|
|
::= { hpSwitchConsoleConfig 1 }
|
|
|
|
hpSwitchTerminalType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
vt100(2),
|
|
ansi(4)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Terminal type of the console device."
|
|
::= { hpSwitchConsoleConfig 2 }
|
|
|
|
hpSwitchConsoleRefRate OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
refRate1(1),
|
|
refRate3(3),
|
|
refRate5(5),
|
|
refRate10(10),
|
|
refRate20(20),
|
|
refRate30(30),
|
|
refRate45(45),
|
|
refRate(60)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The rate, in second per cycle, at which the display
|
|
of various switch measurements."
|
|
::= { hpSwitchConsoleConfig 3 }
|
|
|
|
hpSwitchDisplayedEvent OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
major(2),
|
|
notInfo(3),
|
|
all(4),
|
|
debug(5)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of event messages are automatically
|
|
displayed on the console."
|
|
::= { hpSwitchConsoleConfig 4 }
|
|
|
|
hpSwitchConsoleConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The configuration status of this group of objects.
|
|
If one or more variables in this group were
|
|
reconfigurated since last reboot and required reboot
|
|
to take effect, the value of this variable will be
|
|
set to notInService."
|
|
::= { hpSwitchConsoleConfig 5 }
|
|
|
|
|
|
|
|
hpSwitchPortConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 3 }
|
|
|
|
hpSwitchPortTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchPortEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the current
|
|
port status in this device."
|
|
::= { hpSwitchPortConfig 1 }
|
|
|
|
hpSwitchPortEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchPortEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "Information about a specific port status in this
|
|
device."
|
|
INDEX { hpSwitchPortIndex }
|
|
::= { hpSwitchPortTable 1 }
|
|
|
|
HpSwitchPortEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchPortIndex INTEGER,
|
|
hpSwitchPortType HpSwitchPortType,
|
|
hpSwitchPortDescr DisplayString,
|
|
hpSwitchPortAdminStatus INTEGER,
|
|
hpSwitchPortEtherMode INTEGER,
|
|
hpSwitchPortVgMode INTEGER,
|
|
hpSwitchPortLinkbeat INTEGER,
|
|
hpSwitchPortTrunkGroup INTEGER,
|
|
hpSwitchPortBcastLimit INTEGER,
|
|
hpSwitchPortFastEtherMode INTEGER,
|
|
hpSwitchPortFlowControl INTEGER,
|
|
-- hpSwitchPortBcastPktLimit INTEGER,
|
|
hpSwitchPortTrunkType INTEGER,
|
|
hpSwitchPortTrunkLACPStatus INTEGER,
|
|
hpSwitchPortMDIXStatus INTEGER,
|
|
hpSwitchPortAutoMDIX INTEGER
|
|
}
|
|
|
|
hpSwitchPortIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in
|
|
the Interfaces Table."
|
|
::= { hpSwitchPortEntry 1 }
|
|
|
|
hpSwitchPortType OBJECT-TYPE
|
|
SYNTAX HpSwitchPortType
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of port."
|
|
::= { hpSwitchPortEntry 2 }
|
|
|
|
hpSwitchPortDescr OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE (0..255))
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "A textual string containing information about the
|
|
interface."
|
|
::= { hpSwitchPortEntry 3 }
|
|
|
|
hpSwitchPortAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "The desired state of the interface. This variable is
|
|
similar to the ifAdminStatus but instead of keeping
|
|
the operational status, this variable maintain the
|
|
desired state in the configuration data base."
|
|
::= { hpSwitchPortEntry 4 }
|
|
|
|
hpSwitchPortEtherMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
half-duplex(1),
|
|
full-duplex(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of transmission on this port. This
|
|
variable is valid only if the hpSwitchPortType
|
|
was Ethernet."
|
|
::= { hpSwitchPortEntry 5 }
|
|
|
|
hpSwitchPortVgMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
master(1),
|
|
endNode(2),
|
|
autoDetect(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of transmission on this port. This variable
|
|
is valid only if the hpSwitchPortType was VG."
|
|
::= { hpSwitchPortEntry 6 }
|
|
|
|
hpSwitchPortLinkbeat OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The linkbeat status of this port."
|
|
::= { hpSwitchPortEntry 7 }
|
|
|
|
hpSwitchPortTrunkGroup OBJECT-TYPE
|
|
SYNTAX INTEGER (0..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The trunk group this port belong to."
|
|
::= { hpSwitchPortEntry 8 }
|
|
|
|
hpSwitchPortBcastLimit OBJECT-TYPE
|
|
SYNTAX INTEGER (0..99)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The percentage of network bandwidth consumed by
|
|
broadcast traffic through this port. If the value of
|
|
this variable is 0, there will be no broadcast limit."
|
|
::= { hpSwitchPortEntry 9 }
|
|
|
|
hpSwitchPortFastEtherMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
half-duplex-10Mbits(1),
|
|
half-duplex-100Mbits(2),
|
|
full-duplex-10Mbits(3),
|
|
full-duplex-100Mbits(4),
|
|
auto-neg(5),
|
|
full-duplex-1000Mbits(6),
|
|
auto-10Mbits(7),
|
|
auto-100Mbits(8),
|
|
auto-1000Mbits(9),
|
|
full-duplex-10Gbits(10),
|
|
auto-10-100Mbits(11)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of transmission on this port. This variable
|
|
is valid only if the hpSwitchPortType was Fast
|
|
Ethernet."
|
|
::= { hpSwitchPortEntry 10 }
|
|
|
|
hpSwitchPortFlowControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disable(1),
|
|
enable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The Flow Control of this port."
|
|
::= { hpSwitchPortEntry 11}
|
|
|
|
-- hpSwitchPortBcastPktLimit OBJECT-TYPE
|
|
-- SYNTAX INTEGER (0..1500000)
|
|
-- ACCESS read-write
|
|
-- STATUS mandatory
|
|
-- DESCRIPTION "Network bandwidth in packets per second consumed
|
|
-- by broadcast traffic through this port. If the value
|
|
-- of this variable is 0, there will be no broadcast
|
|
-- limit."
|
|
-- ::= { hpSwitchPortEntry 12 }
|
|
|
|
hpSwitchPortTrunkType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
trunk(1),
|
|
fecAuto(2),
|
|
saTrunk(3),
|
|
lacpTrk(4),
|
|
none(5)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Used in conjunction with hpSwitchPortTrunkGroup to
|
|
determine what type of trunk and which group it
|
|
belongs to. If hpSwitchPortTrunkGroup is set to 0,
|
|
trunking is disabled on the port and this variable
|
|
becomes a 'don't care'"
|
|
::= { hpSwitchPortEntry 13 }
|
|
|
|
hpSwitchPortTrunkLACPStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
active(2),
|
|
passive(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Used in conjunction with hpSwitchPortTrunkType.
|
|
When the trunk is a LACP trunk, this variable defines
|
|
its administrative status"
|
|
::= { hpSwitchPortEntry 14 }
|
|
|
|
hpSwitchPortMDIXStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
not-applicable(1),
|
|
mdi(2),
|
|
mdix(3),
|
|
automdix(4)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "Shows the MDI/MDIX setting for an RJ-45 port.
|
|
Returns a value of 'not-applicable' for all
|
|
ports except RJ-45 ports."
|
|
::= { hpSwitchPortEntry 15 }
|
|
|
|
hpSwitchPortAutoMDIX OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
not-applicable(1),
|
|
mdi(2),
|
|
mdix(3),
|
|
automdix(4)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Sets the MDI/MDIX value for an RJ-45 port.
|
|
Negates need for crossover cables. 'automdix',
|
|
'mdi', or 'mdix' may be set when the port
|
|
configuration is set to any auto-negotiation mode,
|
|
for example 'auto' or 'auto-100', or to any of the
|
|
fixed-configuration modes, for example '100-full'.
|
|
The MDI/MDIX value is maintained across port
|
|
configuration mode changes."
|
|
::= { hpSwitchPortEntry 16 }
|
|
|
|
hpSwitchPortConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The configuration status of this group of objects. If
|
|
one or more variables in this group were
|
|
reconfigured since last reboot and required reboot to
|
|
take effect, the value of this variable will be set to
|
|
notInService."
|
|
::= { hpSwitchPortConfig 2 }
|
|
|
|
|
|
hpSwitchIpxConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 4 }
|
|
|
|
hpSwitchIpxConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The status of the IPX configuration table."
|
|
::= { hpSwitchIpxConfig 2 }
|
|
|
|
|
|
hpSwitchIpConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 5 }
|
|
|
|
hpSwitchIpTimepAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
manual(1),
|
|
disable(2),
|
|
dhcp(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the Time protocol."
|
|
::= { hpSwitchIpConfig 1 }
|
|
|
|
hpSwitchIpTimepServerAddr OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "### deprecated ### The IP address of the Time server."
|
|
::= { hpSwitchIpConfig 2 }
|
|
|
|
hpSwitchIpTimepPollInterval OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The client poll interval of the Time server in
|
|
minutes."
|
|
::= { hpSwitchIpConfig 3 }
|
|
|
|
hpSwitchIpConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS obsolete
|
|
DESCRIPTION "The configuration status of the Timep and IP
|
|
related objects."
|
|
::= { hpSwitchIpConfig 5 }
|
|
|
|
hpSwitchIpTftpMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
secure(1),
|
|
unsecure(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational mode of the Tftp protocol."
|
|
::= { hpSwitchIpConfig 6 }
|
|
|
|
hpSwitchIpTimepInetServerAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The IP address type of the Time server."
|
|
::= { hpSwitchIpConfig 7 }
|
|
|
|
hpSwitchIpTimepInetServerAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The IP address (of the Time server)to which this entry's
|
|
addressing information pertains.
|
|
hpSwitchIpTimepInetServerAddr is always interpreted within
|
|
the context of hpSwitchIpTimepInetServerAddrType."
|
|
::= { hpSwitchIpConfig 8 }
|
|
|
|
|
|
hpSwitchSerialLinkConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 6 }
|
|
|
|
hpSwitchSLinkBaudRate OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
speedSense(1),
|
|
baudRate300(2),
|
|
baudRate600(3),
|
|
baudRate1200(4),
|
|
baudRate2400(5),
|
|
baudRate4800(6),
|
|
baudRate9600(7),
|
|
baudRate19200(8),
|
|
baudRate38400(9),
|
|
baudRate57600(10),
|
|
baudRate115200(11)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The rate of data transfer between the console and
|
|
the node. baudRate1 is speed sense."
|
|
::= { hpSwitchSerialLinkConfig 1 }
|
|
|
|
hpSwitchSLinkFlowCtrl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
xonXoff(2),
|
|
robustXonXoff(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The flow-control mechanism between the console and
|
|
the switch."
|
|
::= { hpSwitchSerialLinkConfig 2 }
|
|
|
|
hpSwitchSLinkConnInactTime OBJECT-TYPE
|
|
SYNTAX INTEGER (0..120)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of minutes to wait after no character was
|
|
input to log out the console. Valid values are 0 (not
|
|
to log out of the console for inactivity) through 120
|
|
(two hours)."
|
|
::= { hpSwitchSerialLinkConfig 3 }
|
|
|
|
hpSwitchSLinkModemConnTime OBJECT-TYPE
|
|
SYNTAX INTEGER (0..300)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of seconds to wait for data mode and
|
|
clear to send and receiver ready signals after
|
|
asserting request to send and terminal ready signals.
|
|
Valid values are 0 (switch will wait forever for the
|
|
modem) through 300 (5 minutes)."
|
|
::= { hpSwitchSerialLinkConfig 4 }
|
|
|
|
hpSwitchSLinkModemLostRecvTime OBJECT-TYPE
|
|
SYNTAX INTEGER (0..5000)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of milliseconds the receiver ready signal
|
|
is allowed to drop before the switch will disconnect
|
|
the modem. Valid values are 0 (the switch will wait
|
|
forever) through 5000 (5 seconds)."
|
|
::= { hpSwitchSerialLinkConfig 5 }
|
|
|
|
hpSwitchSLinkModemDisConnTime OBJECT-TYPE
|
|
SYNTAX INTEGER (0..60)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of seconds to wait after the modem is
|
|
disconnected before allowing the modem to be
|
|
reconnected. Valid values are 0 (allow a connection
|
|
as soon as possible, the default) through 60 (1
|
|
minute)."
|
|
::= { hpSwitchSerialLinkConfig 6 }
|
|
|
|
hpSwitchSLinkParity OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
parityNone(1),
|
|
parityOdd(2),
|
|
parityEven(3)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of parity to use between the console and
|
|
the node."
|
|
::= { hpSwitchSerialLinkConfig 7 }
|
|
|
|
hpSwitchSLinkCharBits OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
char8Bits(1),
|
|
char7Bits(2)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of bits per character to use between
|
|
the console and the node."
|
|
::= { hpSwitchSerialLinkConfig 8 }
|
|
|
|
hpSwitchSLinkStopBits OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
stop1Bits(1),
|
|
stop1andHalfBits(2),
|
|
stop2Bits(3)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The number of stop bots to use when communicating
|
|
between the console and the node."
|
|
::= { hpSwitchSerialLinkConfig 9 }
|
|
|
|
hpSwitchSLinkConfigStatus OBJECT-TYPE
|
|
SYNTAX ConfigStatus
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The configuration status of this group of objects.
|
|
If one or more variables in this group were
|
|
reconfigured since last reboot and required reboot
|
|
to take effect, the value of this variable will be
|
|
set to notInService."
|
|
::= { hpSwitchSerialLinkConfig 10 }
|
|
|
|
|
|
hpSwitchFilterConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 8 }
|
|
|
|
-- A sample of the traffic filter
|
|
|
|
-- type MacAddr ProType SrcPort PortMask
|
|
|
|
-- unicast MAC address X port # Bit Mask of ports
|
|
-- multicast MAC address X X Bit Mask of ports
|
|
-- port X X port # Bit Mask of ports
|
|
-- level 3 X protocol X Bit Mask of ports
|
|
|
|
hpSwitchFilterConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchFilterConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the
|
|
traffic filter configuration in this device."
|
|
::= { hpSwitchFilterConfig 1 }
|
|
|
|
hpSwitchFilterConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchFilterConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "Information about a traffic filter configuration
|
|
in this device."
|
|
INDEX { hpSwitchFilterIndex }
|
|
::= { hpSwitchFilterConfigTable 1 }
|
|
|
|
HpSwitchFilterConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchFilterIndex INTEGER,
|
|
hpSwitchFilterType INTEGER,
|
|
hpSwitchFilterSrcPort INTEGER,
|
|
hpSwitchFilterMacAddr MacAddress,
|
|
hpSwitchFilterProtocolType INTEGER,
|
|
hpSwitchFilterPortMask OCTET STRING,
|
|
hpSwitchFilterEntryStatus RowStatus
|
|
}
|
|
|
|
hpSwitchFilterIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "An index that uniquely identifies a traffic filter
|
|
for which this entry contains information."
|
|
::= { hpSwitchFilterConfigEntry 1 }
|
|
|
|
hpSwitchFilterType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
multicast(1),
|
|
level-3(2),
|
|
port(3),
|
|
unicast(4)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of filter."
|
|
::= { hpSwitchFilterConfigEntry 2 }
|
|
|
|
hpSwitchFilterSrcPort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable is required when a port filter or
|
|
unicast filter was configurated. It will be ignored
|
|
otherwise."
|
|
::= { hpSwitchFilterConfigEntry 3 }
|
|
|
|
hpSwitchFilterMacAddr OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable is valid only if a unicast or
|
|
multicast filter was defined. It will be ignored
|
|
otherwise."
|
|
::= { hpSwitchFilterConfigEntry 4 }
|
|
|
|
hpSwitchFilterProtocolType OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable is valid only if a level-3 filter
|
|
was defined. It will be ignored otherwise. This
|
|
variable will contain either a etherType (DIX
|
|
Ethernet) or SAP(IEEE 802) value of the level-3
|
|
protocol."
|
|
::= { hpSwitchFilterConfigEntry 5 }
|
|
|
|
hpSwitchFilterPortMask OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable specifies a group of ports whose
|
|
traffic will be filtered. Each octet within the value
|
|
of this object specifies a set of eight ports, with
|
|
the first octet specifying ports 1 through 8, the
|
|
second octet specifying ports 9 through 16, etc.
|
|
Within each octet, the most significant bit represents
|
|
the lowest numbered port, and the least significant bit
|
|
represents the highest numbered port. Thus, each port
|
|
of the switch is represented by a single bit within
|
|
the value of this object."
|
|
::= { hpSwitchFilterConfigEntry 6 }
|
|
|
|
hpSwitchFilterEntryStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The status of a filter entry."
|
|
::= { hpSwitchFilterConfigEntry 7 }
|
|
|
|
|
|
hpSwitchProbeConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 9 }
|
|
|
|
hpSwitchProbeType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ports(1),
|
|
vlan(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "If the value of this variable is equal to 1, the
|
|
probe will monitor those ports specified by
|
|
hpSwitchProbedPortMask, otherwise all of the port
|
|
belong to the virtual LAN specified by
|
|
hpSwitchProbedVlanId will be monitored."
|
|
::= { hpSwitchProbeConfig 1 }
|
|
|
|
hpSwitchProbedVlanId OBJECT-TYPE
|
|
SYNTAX VlanID
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "The probed virtual LAN."
|
|
::= { hpSwitchProbeConfig 2 }
|
|
|
|
hpSwitchProbePort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "The port that every packet passes through those
|
|
probed ports will be copied to."
|
|
::= { hpSwitchProbeConfig 3 }
|
|
|
|
hpSwitchProbeAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "The operational status of the probing function"
|
|
::= { hpSwitchProbeConfig 4 }
|
|
|
|
hpSwitchProbedPortMask OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
ACCESS read-write
|
|
STATUS obsolete
|
|
DESCRIPTION "This variable specifies a group of ports which will
|
|
be probed. Each octet within the value of this
|
|
object specifies a set of eight ports, with the
|
|
first octet specifying ports 1 through 8, the second
|
|
octet specifying ports 9 through 16, etc. Within each
|
|
octet, the most significant bit represents the lowest
|
|
numbered port, and the least significant bit
|
|
represents the highest numbered port. Thus, each port
|
|
of the switch is represented by a single bit within
|
|
the value of this object."
|
|
::= { hpSwitchProbeConfig 5 }
|
|
|
|
|
|
-- The FDDI IP Fragmention Configuration group
|
|
|
|
hpSwitchFddiIpFragConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 11 }
|
|
|
|
-- The FDDI IP Fragmention Configuration Table
|
|
|
|
hpSwitchFddiIpFragConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchFddiIpFragConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A list of IP fragmentation configuration
|
|
parameters for the FDDI cards in the switch."
|
|
::= { hpSwitchFddiIpFragConfig 1 }
|
|
|
|
hpSwitchFddiIpFragConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchFddiIpFragConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An Fddi IP fragmentation entry which is
|
|
containing configurable options for the FDDI
|
|
cards in the switch."
|
|
INDEX { hpSwitchFddiIpFragConfigIndex }
|
|
::= { hpSwitchFddiIpFragConfigTable 1 }
|
|
|
|
HpSwitchFddiIpFragConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchFddiIpFragConfigIndex INTEGER,
|
|
hpSwitchFddiIpFragConfigStatus INTEGER
|
|
}
|
|
|
|
hpSwitchFddiIpFragConfigIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "A unique value for each FDDI Card.
|
|
The value for each FDDI card must remain constant
|
|
at least from one re-initialization of the entity's
|
|
network management system to the next
|
|
re-initialization."
|
|
::= { hpSwitchFddiIpFragConfigEntry 1 }
|
|
|
|
hpSwitchFddiIpFragConfigStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of FDDI IP fragmentation
|
|
for each FDDI card.
|
|
enable(1): FDDI card will fragment all packets which
|
|
are bigger then the Ethernet packet size
|
|
limitation, 1518 Bytes.
|
|
disable(2): FDDI card will drop all packets which
|
|
are bigger then the Ethernet packet size
|
|
limitation, 1518 Bytes."
|
|
::= { hpSwitchFddiIpFragConfigEntry 2 }
|
|
|
|
|
|
hpSwitchABCConfig OBJECT IDENTIFIER ::= {hpSwitchConfig 12 }
|
|
|
|
hpSwitchABCConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchABCConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A list of Automatic Broadcast Control (ABC
|
|
disable/enable entries for each VLAN on the switch."
|
|
::= { hpSwitchABCConfig 1 }
|
|
|
|
hpSwitchABCConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchABCConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "Contains the ABC status for each VLAN on the switch,
|
|
including IP RIP control and IPX RIP/SAP control."
|
|
INDEX { hpSwitchABCConfigVlan }
|
|
::= { hpSwitchABCConfigTable 1 }
|
|
|
|
HpSwitchABCConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchABCConfigVlan VlanID,
|
|
hpSwitchABCConfigControl INTEGER,
|
|
hpSwitchABCConfigIpRipControl INTEGER,
|
|
hpSwitchABCConfigIpxRipSapControl INTEGER,
|
|
hpSwitchABCConfigVlanBcastLimit INTEGER,
|
|
-- hpSwitchABCConfigVlanBcastPktLimit INTEGER,
|
|
hpSwitchABCConfigAutoGatewayConfig INTEGER
|
|
}
|
|
|
|
hpSwitchABCConfigVlan OBJECT-TYPE
|
|
SYNTAX VlanID
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The user is able to enable/disable ABC on a per VLAN
|
|
basis, so the VLAN serves as an index into the ABC
|
|
configuration table."
|
|
::= { hpSwitchABCConfigEntry 1 }
|
|
|
|
hpSwitchABCConfigControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ipipx(1),
|
|
ip(2),
|
|
ipx(3),
|
|
disable(4)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "ABC control is either IP&IPX or IP or IPX or disabled
|
|
for each VLAN on the switch."
|
|
::= { hpSwitchABCConfigEntry 2 }
|
|
|
|
hpSwitchABCConfigIpRipControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "IP RIP control. If this feature is enabled then IP
|
|
RIP packets will only be forwarded on ports, within
|
|
its VLAN domain, that have heard RIPs before. If
|
|
this feature is disabled then IP RIP packets seen by
|
|
a given port will be forwarded to all ports within its
|
|
VLAN domain."
|
|
::= { hpSwitchABCConfigEntry 3 }
|
|
|
|
hpSwitchABCConfigIpxRipSapControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "IPX RIP/SAP control. If this feature is enabled then
|
|
IPX RIP/SAP packets will only be forwarded on ports,
|
|
within its VLAN domain, that have previously seen
|
|
RIP/SAP packets. If this feature is disabled then
|
|
IPX RIP and SAP packets seen by a given port will be
|
|
forwarded to all ports within its VLAN domain."
|
|
::= { hpSwitchABCConfigEntry 4 }
|
|
|
|
hpSwitchABCConfigVlanBcastLimit OBJECT-TYPE
|
|
SYNTAX INTEGER (0..99)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The percentage of network bandwidth consumed by
|
|
broadcast traffic through VLAN. If the value of this
|
|
variable is 0, there will be no broadcast limit. There
|
|
is a default value chosen when ABC is enabled."
|
|
::= { hpSwitchABCConfigEntry 5 }
|
|
|
|
-- hpSwitchABCConfigVlanBcastPktLimit OBJECT-TYPE
|
|
-- SYNTAX INTEGER (0..2147483647)
|
|
-- ACCESS read-write
|
|
-- STATUS mandatory
|
|
-- DESCRIPTION "Network bandwidth in packets per second consumed
|
|
-- by broadcast traffic through VLAN. If the value of
|
|
-- this variable is 0, there will be no broadcast limit.
|
|
-- There is a default value chosen when ABC is enabled."
|
|
-- ::= { hpSwitchABCConfigEntry 6 }
|
|
|
|
hpSwitchABCConfigAutoGatewayConfig OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "If this feature is enabled then DHCP packets both
|
|
ucast and bcast with UDP destination port 68 will be
|
|
intercepted. DHCP packets with the router option in
|
|
the options field in the DHCP message will be
|
|
modified so that the first daddress in the router
|
|
option is the same as the clients address. Thus the
|
|
client will be its own default gateway. If this
|
|
feature is disabled DHCP packtes will be forwarded as
|
|
usual."
|
|
::= { hpSwitchABCConfigEntry 7 }
|
|
|
|
|
|
hpSwitchStpConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 14 }
|
|
|
|
hpSwitchStpVlanTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchStpVlanEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains vlan-specific information
|
|
for the Spanning Tree Protocol."
|
|
::= { hpSwitchStpConfig 1}
|
|
|
|
hpSwitchStpVlanEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchStpVlanEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A list of information maintained by every port
|
|
about the Spanning Tree Protocol state for that
|
|
port."
|
|
INDEX { hpSwitchStpVlan }
|
|
::= { hpSwitchStpVlanTable 1 }
|
|
|
|
HpSwitchStpVlanEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchStpVlan VlanID,
|
|
hpSwitchStpAdminStatus INTEGER,
|
|
hpSwitchStpPriority INTEGER,
|
|
hpSwitchStpMaxAge Timeout,
|
|
hpSwitchStpHelloTime Timeout,
|
|
hpSwitchStpForwardDelay Timeout
|
|
}
|
|
|
|
hpSwitchStpVlan OBJECT-TYPE
|
|
SYNTAX VlanID
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the spanning tree
|
|
protocol."
|
|
::= { hpSwitchStpVlanEntry 1 }
|
|
|
|
hpSwitchStpAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the spanning tree
|
|
protocol."
|
|
::= { hpSwitchStpVlanEntry 2 }
|
|
|
|
hpSwitchStpPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The value of the write-able portion of the Bridge
|
|
ID, i.e., the first two octets of the (8 octet
|
|
long) Bridge ID. The other (last) 6 octets of the
|
|
Bridge ID are given by the value of
|
|
dot1dBaseBridgeAddress."
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.3.7"
|
|
::= { hpSwitchStpVlanEntry 3 }
|
|
|
|
hpSwitchStpMaxAge OBJECT-TYPE
|
|
SYNTAX Timeout
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum age of Spanning Tree Protocol
|
|
information learned from the network on any port
|
|
before it is discarded, in units of hundredths of
|
|
a second. This is the actual value that this
|
|
bridge is currently using."
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.3.4"
|
|
::= { hpSwitchStpVlanEntry 4 }
|
|
|
|
hpSwitchStpHelloTime OBJECT-TYPE
|
|
SYNTAX Timeout
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The amount of time between the transmission of
|
|
Configuration bridge PDUs by this node on any port
|
|
when it is the root of the spanning tree or trying
|
|
to become so, in units of hundredths of a second.
|
|
This is the actual value that this bridge is
|
|
currently using."
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.3.5"
|
|
::= { hpSwitchStpVlanEntry 5 }
|
|
|
|
hpSwitchStpForwardDelay OBJECT-TYPE
|
|
SYNTAX Timeout
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This time value, measured in units of hundredths
|
|
of a second, controls how fast a port changes its
|
|
spanning state when moving towards the Forwarding
|
|
state. The value determines how long the port
|
|
stays in each of the Listening and Learning
|
|
states, which precede the Forwarding state. This
|
|
value is also used, when a topology change has
|
|
been detected and is underway, to age all dynamic
|
|
entries in the Forwarding Database. [Note that
|
|
this value is the one that this bridge is
|
|
currently using, in contrast to
|
|
dot1dBridgeForwardDelay which is the value that
|
|
this bridge and all others would start using
|
|
if/when this bridge were to become the root.]"
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.3.6"
|
|
::= { hpSwitchStpVlanEntry 6 }
|
|
|
|
hpSwitchStpPortTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchStpPortEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains port-specific information
|
|
for the Spanning Tree Protocol."
|
|
::= { hpSwitchStpConfig 2 }
|
|
|
|
hpSwitchStpPortEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchStpPortEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A list of information maintained by every port
|
|
about the Spanning Tree Protocol state for that
|
|
port."
|
|
INDEX { hpSwitchStpPort }
|
|
::= { hpSwitchStpPortTable 1 }
|
|
|
|
HpSwitchStpPortEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchStpPort INTEGER,
|
|
hpSwitchStpPortType HpSwitchPortType,
|
|
hpSwitchStpPortSrcMac MacAddress,
|
|
hpSwitchStpPortPriority INTEGER,
|
|
hpSwitchStpPortPathCost INTEGER,
|
|
hpSwitchStpPortMode INTEGER,
|
|
hpSwitchStpPortBpduFilter INTEGER,
|
|
hpSwitchStpPortBpduProtection INTEGER,
|
|
hpSwitchStpPortErrantBpduCounter Counter,
|
|
hpSwitchStpPortPvstFilter INTEGER,
|
|
hpSwitchStpPortPvstProtection INTEGER
|
|
}
|
|
|
|
hpSwitchStpPort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The port number of the port for which this entry
|
|
contains Spanning Tree Protocol management
|
|
information."
|
|
REFERENCE
|
|
"IEEE 802.1D-1990: Section 6.8.2.1.2"
|
|
::= { hpSwitchStpPortEntry 1 }
|
|
|
|
hpSwitchStpPortType OBJECT-TYPE
|
|
SYNTAX HpSwitchPortType
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of port."
|
|
::= { hpSwitchStpPortEntry 2 }
|
|
|
|
hpSwitchStpPortSrcMac OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The source MAC address used by the spanning
|
|
tree protocol."
|
|
::= { hpSwitchStpPortEntry 3 }
|
|
|
|
hpSwitchStpPortPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The value of the priority field which is
|
|
contained in the first (in network byte order)
|
|
octet of the (2 octet long) Port ID. The other
|
|
octet of the Port ID is given by the value of
|
|
dot1dStpPort."
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.5.1"
|
|
::= { hpSwitchStpPortEntry 4 }
|
|
|
|
hpSwitchStpPortPathCost OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The contribution of this port to the path cost of
|
|
paths towards the spanning tree root which include
|
|
this port. 802.1D-1990 recommends that the
|
|
default value of this parameter be in inverse
|
|
proportion to the speed of the attached LAN."
|
|
REFERENCE "IEEE 802.1D-1990: Section 4.5.5.3"
|
|
::= { hpSwitchStpPortEntry 5 }
|
|
|
|
hpSwitchStpPortMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
normal(1),
|
|
fast(2),
|
|
uplink(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "If the value of this variable is set to fast(2), the
|
|
port will go directly into the Forwarding State when a
|
|
device is connected to it. Use this feature only on
|
|
ports that are connected to an individual PC or
|
|
Workstation, to allow these ports to come up and
|
|
move quickly to the Forwarding State instead of going
|
|
through the normal STP initialization process.
|
|
|
|
Caution: Changing the value of this variable to fast(2)
|
|
on ports connected to a hub or switch may cause loops
|
|
in your network."
|
|
::= { hpSwitchStpPortEntry 6 }
|
|
|
|
hpSwitchStpPortBpduFilter OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
true(1),
|
|
false(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "Setting True will cause port to ignore ingress BPDUs
|
|
and not generate egress BPDUs, as the result the port
|
|
will stay in forwarding state. Default is False."
|
|
DEFVAL { false }
|
|
::= { hpSwitchStpPortEntry 7 }
|
|
|
|
hpSwitchStpPortBpduProtection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
true(1),
|
|
false(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "Setting True indicates that no BPDUs are expected to
|
|
be received on this port. At the reception of BPDUs
|
|
the BPDU protection mechanism will disable this port
|
|
and port will transition into bpduError state.
|
|
Default is False."
|
|
DEFVAL { false }
|
|
::= { hpSwitchStpPortEntry 8 }
|
|
|
|
hpSwitchStpPortErrantBpduCounter OBJECT-TYPE
|
|
SYNTAX Counter
|
|
ACCESS read-only
|
|
STATUS optional
|
|
DESCRIPTION "Counts the number of BPDUs that were not expected
|
|
to be received on this port. This counter gets
|
|
incremented only if hpSwitchStpPortBpduProtection,
|
|
hpSwitchStpPortBpduFilter, hpSwitchStpPortPvstFilter,
|
|
or hpSwitchStpPvstProtection is True for the port,
|
|
otherwise it is cleared to zero."
|
|
::= { hpSwitchStpPortEntry 9 }
|
|
|
|
hpSwitchStpPortPvstFilter OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "Setting True will cause the port to ignore incoming
|
|
PVST BPDUs.
|
|
Default is False."
|
|
DEFVAL { false }
|
|
::= { hpSwitchStpPortEntry 10 }
|
|
|
|
hpSwitchStpPortPvstProtection OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "Setting True indicates that any PVST BPDUs arriving
|
|
on this port should be discarded and that this will
|
|
cause the port to be disabled. The port will remain
|
|
disabled for the time period indicated by
|
|
hpSwitchStpBpduProtectionTimeout.
|
|
Default is False."
|
|
DEFVAL { false }
|
|
::= { hpSwitchStpPortEntry 11 }
|
|
|
|
hpSwitchStpTrapCntl OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
errantBpdu(0)
|
|
}
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "Controls generation of SNMP traps by STP-enabled switch
|
|
for events defined in this MIB.
|
|
The set bit means 'enabled'.
|
|
|
|
- errantBpdu(0)
|
|
The state of this bit specifies whether the
|
|
notification trap allowed to be send when
|
|
unexpected (errant) BPDU is received on a port."
|
|
|
|
::= { hpSwitchStpConfig 3 }
|
|
|
|
hpSwitchStpBpduProtectionTimeout OBJECT-TYPE
|
|
SYNTAX INTEGER
|
|
ACCESS read-write
|
|
STATUS optional
|
|
DESCRIPTION "The duration of time in seconds when a protected port
|
|
affected by receiving of an unauthorized BPDU will
|
|
remain in down state. The zero value means infinity."
|
|
DEFVAL { 0 }
|
|
::= { hpSwitchStpConfig 4 }
|
|
|
|
hpSwitchIgmpConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 15 }
|
|
|
|
hpSwitchIgmpConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchIgmpConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the IGMP
|
|
Querier capacity or High Priority Forward
|
|
configuration on any given vlan on the switch."
|
|
::= { hpSwitchIgmpConfig 1 }
|
|
|
|
hpSwitchIgmpConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchIgmpConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "Information about the IGMP Querier feature associated
|
|
with a specific virtal LAN in this device."
|
|
INDEX { hpSwitchIgmpVlanIndex }
|
|
::= { hpSwitchIgmpConfigTable 1 }
|
|
|
|
HpSwitchIgmpConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchIgmpVlanIndex VlanID,
|
|
hpSwitchIgmpState INTEGER,
|
|
hpSwitchIgmpQuerierState INTEGER,
|
|
hpSwitchIgmpPriorityState INTEGER,
|
|
hpSwitchIgmpQuerierInterval INTEGER
|
|
}
|
|
|
|
hpSwitchIgmpVlanIndex OBJECT-TYPE
|
|
SYNTAX VlanID
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "An index that uniquely identifies the IGMP
|
|
configuration of a virtual LAN for which this entry
|
|
contains information."
|
|
::= { hpSwitchIgmpConfigEntry 1 }
|
|
|
|
hpSwitchIgmpState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP support for
|
|
this virtual LAN."
|
|
::= { hpSwitchIgmpConfigEntry 2 }
|
|
|
|
hpSwitchIgmpQuerierState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP Querier
|
|
functionality for this virtual LAN."
|
|
::= { hpSwitchIgmpConfigEntry 3 }
|
|
|
|
hpSwitchIgmpPriorityState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP Forward with High
|
|
Priority mode for this virtual LAN."
|
|
::= { hpSwitchIgmpConfigEntry 4 }
|
|
|
|
hpSwitchIgmpQuerierInterval OBJECT-TYPE
|
|
SYNTAX INTEGER (5..300)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The time (in seconds) to wait between Querier
|
|
election cycles for this virtual LAN."
|
|
::= { hpSwitchIgmpConfigEntry 5 }
|
|
|
|
hpSwitchIgmpPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchIgmpPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the IGMP port
|
|
configurations on this switch."
|
|
::= { hpSwitchIgmpConfig 2 }
|
|
|
|
hpSwitchIgmpPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchIgmpPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each IGMP port
|
|
configuration."
|
|
INDEX { hpSwitchIgmpPortIndex }
|
|
::= { hpSwitchIgmpPortConfigTable 1 }
|
|
|
|
HpSwitchIgmpPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchIgmpPortIndex INTEGER,
|
|
hpSwitchIgmpPortType HpSwitchPortType,
|
|
hpSwitchIgmpIpMcastState INTEGER
|
|
}
|
|
|
|
hpSwitchIgmpPortIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in
|
|
the Interfaces Table."
|
|
::= { hpSwitchIgmpPortConfigEntry 1 }
|
|
|
|
hpSwitchIgmpPortType OBJECT-TYPE
|
|
SYNTAX HpSwitchPortType
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of port."
|
|
::= { hpSwitchIgmpPortConfigEntry 2 }
|
|
|
|
hpSwitchIgmpIpMcastState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
auto(1),
|
|
blocked(2),
|
|
forward(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP feature for this
|
|
port or trunk. 1 implies that all IP Multicast
|
|
traffic will be monitored on the port, 2 implies that
|
|
IP Multicast traffic will be dropped on the port, and
|
|
3 implies that all IP Multicast traffic will be
|
|
forwarded without the switch examining it."
|
|
::= { hpSwitchIgmpPortConfigEntry 3 }
|
|
|
|
|
|
hpSwitchIgmpPortConfigTable2 OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchIgmpPortConfigEntry2
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the IGMP port
|
|
configurations on this switch. This table supercedes
|
|
hpSwitchIgmpPortConfigTable for products which support
|
|
multiple VLANs on each port."
|
|
::= { hpSwitchIgmpConfig 3 }
|
|
|
|
hpSwitchIgmpPortConfigEntry2 OBJECT-TYPE
|
|
SYNTAX HpSwitchIgmpPortConfigEntry2
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each IGMP port
|
|
configuration."
|
|
INDEX { hpSwitchIgmpPortVlanIndex2, hpSwitchIgmpPortIndex2 }
|
|
::= { hpSwitchIgmpPortConfigTable2 1 }
|
|
|
|
HpSwitchIgmpPortConfigEntry2 ::=
|
|
SEQUENCE {
|
|
hpSwitchIgmpPortVlanIndex2 INTEGER,
|
|
hpSwitchIgmpPortIndex2 INTEGER,
|
|
hpSwitchIgmpPortType2 HpSwitchPortType,
|
|
hpSwitchIgmpIpMcastState2 INTEGER,
|
|
hpSwitchIgmpPortForcedLeaveState INTEGER,
|
|
hpSwitchIgmpPortFastLeaveState INTEGER
|
|
}
|
|
|
|
hpSwitchIgmpPortVlanIndex2 OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The Vlan Index value which uniquely identifies a row
|
|
in the Interfaces Table."
|
|
::= { hpSwitchIgmpPortConfigEntry2 1 }
|
|
|
|
hpSwitchIgmpPortIndex2 OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in
|
|
the Interfaces Table."
|
|
::= { hpSwitchIgmpPortConfigEntry2 2 }
|
|
|
|
hpSwitchIgmpPortType2 OBJECT-TYPE
|
|
SYNTAX HpSwitchPortType
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of port."
|
|
::= { hpSwitchIgmpPortConfigEntry2 3 }
|
|
|
|
hpSwitchIgmpIpMcastState2 OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
auto(1),
|
|
blocked(2),
|
|
forward(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP feature for this
|
|
port or trunk. 1 implies that all IP Multicast traffic
|
|
will be monitored on the port, 2 implies that
|
|
IP Multicast traffic will be dropped on the port, and
|
|
3 implies that all IP Multicast traffic will be
|
|
forwarded without the switch examining it."
|
|
::= { hpSwitchIgmpPortConfigEntry2 4 }
|
|
|
|
hpSwitchIgmpPortForcedLeaveState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP feature for this
|
|
port or trunk indicates whether any IGMP V2 Leaves
|
|
received for an IP Multicast group will cause the
|
|
group to be deleted after the
|
|
hpSwitchIgmpForcedLeaveInterval if no new IGMP V2
|
|
Reports are received for that group. Normal behavior
|
|
is for a group issuing a Leave to be deleted after
|
|
the Querier's Maximum Response time if no IGMP V2
|
|
Report is received."
|
|
::= { hpSwitchIgmpPortConfigEntry2 5 }
|
|
|
|
hpSwitchIgmpPortFastLeaveState OBJECT-TYPE
|
|
SYNTAX INTEGER{
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of the IGMP feature for this
|
|
port or trunk indicates whether any IGMP V2 Leaves
|
|
received for an IP Multicast group will cause the
|
|
group to be deleted immediately on single-
|
|
connection ports. Normal behavior is for a group
|
|
issuing a Leave to be deleted after the Querier's
|
|
Maximum Response time if no IGMP V2 Report is
|
|
received."
|
|
::= { hpSwitchIgmpPortConfigEntry2 6 }
|
|
|
|
hpSwitchIgmpForcedLeaveInterval OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "When a port's hpSwitchIgmpPortForcedLeaveState is
|
|
enabled, this is the amount of time allowed for an
|
|
IGMP V2 Report to arrive and cancel deletion of a
|
|
multicast group requested by a previous IGMP V2
|
|
Leave request."
|
|
::= { hpSwitchIgmpConfig 4 }
|
|
|
|
|
|
-- CoS support MIB definition
|
|
hpSwitchCosConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 17 }
|
|
|
|
hpSwitchCosPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS port
|
|
configurations on this switch."
|
|
::= { hpSwitchCosConfig 1 }
|
|
|
|
hpSwitchCosPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each CoS port
|
|
configuration."
|
|
INDEX { hpSwitchCosPortIndex }
|
|
::= { hpSwitchCosPortConfigTable 1 }
|
|
|
|
HpSwitchCosPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosPortIndex INTEGER,
|
|
hpSwitchCosPortType HpSwitchPortType,
|
|
hpSwitchCosPortPriority INTEGER,
|
|
hpSwitchCosPortDSCPPolicy INTEGER,
|
|
hpSwitchCosPortResolvedPriority INTEGER,
|
|
hpSwitchCosPortApplyPolicy INTEGER
|
|
}
|
|
|
|
hpSwitchCosPortIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row
|
|
in the Interfaces Table."
|
|
::= { hpSwitchCosPortConfigEntry 1 }
|
|
|
|
hpSwitchCosPortType OBJECT-TYPE
|
|
SYNTAX HpSwitchPortType
|
|
ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION "The type of port."
|
|
::= { hpSwitchCosPortConfigEntry 2 }
|
|
|
|
hpSwitchCosPortPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
received on the specified port. This value will be
|
|
inserted in the 802.1Q tag and the packet will be
|
|
placed in the appropriate outbound port queue. The
|
|
value of 255 is used to indicate No Override."
|
|
::= { hpSwitchCosPortConfigEntry 3 }
|
|
|
|
hpSwitchCosPortDSCPPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER (1..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The DSCP Policy to assign to packets received on
|
|
the specified Port. This is an index into the
|
|
hpSwitchCosDSCPPolicy table, or the value 255
|
|
indicating no DSCP Policy exists. This policy is
|
|
associated with an 802.1p priority value, which will
|
|
be inserted in the 802.1Q tag and will cause the
|
|
packet to be placed in the appropriate outbound port
|
|
queue. When the packet is IP protocol type, the DSCP
|
|
policy value (a Differentiated Services codepoint)
|
|
will also be written into the Differentiated-Services
|
|
field of the IP Type-of-Service byte."
|
|
::= { hpSwitchCosPortConfigEntry 4 }
|
|
|
|
hpSwitchCosPortResolvedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that will be applied to packets
|
|
received on the specified port. This value
|
|
represents the actual operating value for this CoS
|
|
port entry. A value of 255 represents no override
|
|
of the incoming priority."
|
|
::= { hpSwitchCosPortConfigEntry 5 }
|
|
|
|
hpSwitchCosPortApplyPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
noPolicyOverride(1),
|
|
applyHpSwitchCosPortPriority(2),
|
|
applyHpSwitchCosPortDSCPPolicy(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object determines which configuration policy,
|
|
noPolicyOverride, hpSwitchCosPortPriority or
|
|
hpSwitchCosPortDSCPPolicy, applies for the given
|
|
Port CoS entry. These configuration policies are
|
|
mutually exclusive of one another."
|
|
::= { hpSwitchCosPortConfigEntry 6 }
|
|
|
|
|
|
hpSwitchCosVlanConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosVlanConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS Vlan
|
|
configurations on this switch."
|
|
::= { hpSwitchCosConfig 2 }
|
|
|
|
hpSwitchCosVlanConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosVlanConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each CoS Vlan
|
|
configuration."
|
|
INDEX { hpSwitchCosVlanIndex }
|
|
::= { hpSwitchCosVlanConfigTable 1 }
|
|
|
|
HpSwitchCosVlanConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosVlanIndex VlanID,
|
|
hpSwitchCosVlanPriority INTEGER,
|
|
hpSwitchCosVlanDSCPPolicy INTEGER,
|
|
hpSwitchCosVlanResolvedPriority INTEGER,
|
|
hpSwitchCosVlanApplyPolicy INTEGER
|
|
}
|
|
|
|
hpSwitchCosVlanIndex OBJECT-TYPE
|
|
SYNTAX VlanID
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The index that uniquely identifies the CoS
|
|
configuration of a virtual LAN for which this entry
|
|
contains information."
|
|
::= { hpSwitchCosVlanConfigEntry 1 }
|
|
|
|
hpSwitchCosVlanPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
received on the specified Vlan. This value will be
|
|
inserted in the 802.1Q tag and the packet will be
|
|
placed in the appropriate outbound port queue. The
|
|
value of 255 is used to indicate No Override."
|
|
::= { hpSwitchCosVlanConfigEntry 2 }
|
|
|
|
hpSwitchCosVlanDSCPPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER (1..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The DSCP Policy to assign to packets received on
|
|
the specified Vlan. This is an index into the
|
|
hpSwitchCosDSCPPolicy table, or the value 255
|
|
indicating no DSCP Policy exists. This policy is
|
|
associated with an 802.1p priority value, which
|
|
will be inserted in the 802.1Q tag and will cause
|
|
the packet to be placed in the appropriate outbound
|
|
port queue. When the packet is IP protocol type,
|
|
the DSCP policy value (a Differentiated Services
|
|
codepoint) will also be written into the
|
|
Differentiated-Services field of the IP
|
|
Type-of-Service byte."
|
|
::= { hpSwitchCosVlanConfigEntry 3 }
|
|
|
|
hpSwitchCosVlanResolvedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that will be applied to
|
|
packets received on the specified VLAN. This value
|
|
represents the actual operating value for this CoS
|
|
vlan entry. A value of 255 represents no override of
|
|
the incoming priority ."
|
|
::= { hpSwitchCosVlanConfigEntry 4 }
|
|
|
|
hpSwitchCosVlanApplyPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
noPolicyOverride(1),
|
|
applyHpSwitchCosVlanPriority(2),
|
|
applyHpSwitchCosVlanDSCPPolicy(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object determines which configuration policy,
|
|
noPolicyOverride, hpSwitchCosVlanPriority or
|
|
hpSwitchCosDSCPPolicy, applies for this given Vlan
|
|
CoS entry. These configuration policies are mutually
|
|
exclusive of one another."
|
|
::= { hpSwitchCosVlanConfigEntry 5 }
|
|
|
|
|
|
hpSwitchCosProtocolConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosProtocolConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS
|
|
protocol type configurations on this switch."
|
|
::= { hpSwitchCosConfig 3 }
|
|
|
|
hpSwitchCosProtocolConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosProtocolConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each CoS protocol
|
|
configuration."
|
|
INDEX { hpSwitchCosProtocolType }
|
|
::= { hpSwitchCosProtocolConfigTable 1 }
|
|
|
|
HpSwitchCosProtocolConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosProtocolType INTEGER,
|
|
hpSwitchCosProtocolPriority INTEGER
|
|
}
|
|
|
|
hpSwitchCosProtocolType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ip(1),
|
|
ipx(2),
|
|
arp(3),
|
|
decnet(4),
|
|
appletalk(5),
|
|
sna(6),
|
|
netbios(7)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "Packets with this protocol type will receive the new
|
|
priority value."
|
|
::= { hpSwitchCosProtocolConfigEntry 1 }
|
|
|
|
hpSwitchCosProtocolPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
received for the specified protocol. This value will
|
|
be inserted in the 802.1Q tag and the packet will be
|
|
placed in the appropriate outbound port queue. The
|
|
value of 255 is used to indicate No Override."
|
|
::= { hpSwitchCosProtocolConfigEntry 2 }
|
|
|
|
|
|
hpSwitchCosAddressConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosAddressConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS
|
|
address configurations on this switch."
|
|
::= { hpSwitchCosConfig 4 }
|
|
|
|
hpSwitchCosAddressConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosAddressConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each CoS address
|
|
configuration."
|
|
INDEX { hpSwitchCosAddressIndex }
|
|
::= { hpSwitchCosAddressConfigTable 1 }
|
|
|
|
HpSwitchCosAddressConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosAddressIndex INTEGER,
|
|
hpSwitchCosAddressType INTEGER,
|
|
hpSwitchCosAddressIp IpAddress,
|
|
hpSwitchCosAddressPriority INTEGER,
|
|
hpSwitchCosAddressStatus RowStatus,
|
|
hpSwitchCosAddressDSCPPolicy INTEGER,
|
|
hpSwitchCosAddressResolvedPriority INTEGER,
|
|
hpSwitchCosAddressApplyPolicy INTEGER
|
|
}
|
|
|
|
hpSwitchCosAddressIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The index that uniquely identifies the CoS
|
|
configuration for an address for which this entry
|
|
contains information."
|
|
::= { hpSwitchCosAddressConfigEntry 1 }
|
|
|
|
hpSwitchCosAddressType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ip(1)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of address to configure."
|
|
::= { hpSwitchCosAddressConfigEntry 2 }
|
|
|
|
hpSwitchCosAddressIp OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable is valid only if an IP CoS
|
|
configuration was defined. It will be ignored
|
|
otherwise. Packets with this IP address as a source
|
|
or destination will receive the new priority value."
|
|
::= { hpSwitchCosAddressConfigEntry 3 }
|
|
|
|
hpSwitchCosAddressPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
received for the specified address. This value will
|
|
be inserted in the 802.1Q tag and the packet will be
|
|
placed in the appropriate outbound port queue."
|
|
::= { hpSwitchCosAddressConfigEntry 4 }
|
|
|
|
hpSwitchCosAddressStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The status of a Cos Address entry."
|
|
::= { hpSwitchCosAddressConfigEntry 5 }
|
|
|
|
hpSwitchCosAddressDSCPPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER (1..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The DSCP Policy to assign to packets received for
|
|
the specified address. This is an index into the
|
|
hpSwitchCosDSCPPolicy table, or the value 255
|
|
indicating no DSCP Policy exists. This policy is
|
|
associated with an 802.1p priority value, which
|
|
will be inserted in the 802.1Q tag and will cause
|
|
the packet to be placed in the appropriate outbound
|
|
port queue. The DSCP policy value (a Differentiated
|
|
Services codepoint) will also be written into the
|
|
Differentiated-Services field of the IP
|
|
Type-of-Service byte."
|
|
::= { hpSwitchCosAddressConfigEntry 6 }
|
|
|
|
hpSwitchCosAddressResolvedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that will be applied to packets
|
|
received for the specified address. This value
|
|
represents the actual operating value for this given
|
|
address entry. A value of 255 represents no override."
|
|
::= { hpSwitchCosAddressConfigEntry 7 }
|
|
|
|
hpSwitchCosAddressApplyPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
applyHpSwitchCosAddressPriority(1),
|
|
applyHpSwitchCosAddressDSCPPolicy(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object determines which configuration policy,
|
|
hpSwitchCosAddressPriority or hpSwitchCosDSCPPolicy,
|
|
applies for the given Address CoS entry. These
|
|
configuration policies are mutually exclusive of
|
|
one another."
|
|
DEFVAL { applyHpSwitchCosAddressPriority }
|
|
::= { hpSwitchCosAddressConfigEntry 8 }
|
|
|
|
|
|
hpSwitchCosTosConfig OBJECT IDENTIFIER ::= { hpSwitchCosConfig 5 }
|
|
|
|
hpSwitchCosTosConfigMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disable(1),
|
|
ipprecedence(2),
|
|
diffserv(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The operational status of Type of Service based
|
|
Class of Service."
|
|
::= { hpSwitchCosTosConfig 1 }
|
|
|
|
hpSwitchCosTosConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosTosConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS Type
|
|
of Service configurations on this switch. This table
|
|
is used only when the hpSwitchCosTosConfigMode is set
|
|
to diffserv."
|
|
::= { hpSwitchCosTosConfig 2 }
|
|
|
|
hpSwitchCosTosConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosTosConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each CoS TOS
|
|
configuration."
|
|
INDEX { hpSwitchCosTosIndex }
|
|
::= { hpSwitchCosTosConfigTable 1 }
|
|
|
|
HpSwitchCosTosConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosTosIndex INTEGER,
|
|
hpSwitchCosTosPriority INTEGER,
|
|
hpSwitchCosTosDSCPPolicy INTEGER,
|
|
hpSwitchCosTosResolvedPriority INTEGER,
|
|
hpSwitchCosTosApplyPolicy INTEGER
|
|
}
|
|
|
|
hpSwitchCosTosIndex OBJECT-TYPE
|
|
SYNTAX INTEGER
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "Packets with this value in the upper bits of the Type
|
|
of Service field of the IP protocol header will receive
|
|
the new priority value. For Differentiated Services
|
|
the upper 6 bits of the TOS field are used."
|
|
::= { hpSwitchCosTosConfigEntry 1 }
|
|
|
|
hpSwitchCosTosPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..255)
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
received for the specified TOS. This value will be
|
|
inserted in the 802.1Q tag and the packet will be
|
|
placed in the appropriate outbound port queue. The
|
|
value of 255 is used to indicate No Override."
|
|
::= { hpSwitchCosTosConfigEntry 2 }
|
|
|
|
hpSwitchCosTosDSCPPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER (1..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The DSCP Policy to assign to packets received for
|
|
the specified ToS codepoint. This is an index
|
|
into the hpSwitchCosDSCPPolicy table, or the value
|
|
255 indicating no DSCP Policy exists. The DSCP
|
|
policy is associated with an 802.1p priority value,
|
|
which will be inserted in the 802.1Q tag and will
|
|
cause the packet to be placed in the appropriate
|
|
outbound port queue. The DSCP policy value (a
|
|
Differentiated Services codepoint) will also
|
|
replace the incoming value of the Differentiated
|
|
Services field of the IP Type-of-Service byte."
|
|
::= { hpSwitchCosTosConfigEntry 3 }
|
|
|
|
hpSwitchCosTosResolvedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that will be applied to
|
|
packets received for the specified ToS. This
|
|
value represents the actual operating value for
|
|
this given ToS entry. A value of 255 represents no
|
|
override of the incoming priority. If
|
|
hpSwitchCosTosApplyPolicy is set to
|
|
applyInheritedPriority, the parallel codepoint in
|
|
the hpSwitchCosDSCPPolicyConfigTable is used to
|
|
determine the operating priority. Otherwise if set
|
|
to applyHpSwitchCosTosDSCPPolicy, the priority for
|
|
the codepoint that the hpSwitchCosTosDSCPPolicy is
|
|
indexing will be used."
|
|
::= { hpSwitchCosTosConfigEntry 4 }
|
|
|
|
hpSwitchCosTosApplyPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
applyInheritedPriority(1),
|
|
applyHpSwitchCosTosDSCPPolicy(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object determines which configuration policy,
|
|
applyInheritedPriority or hpSwitchCosTosDSCPPolicy,
|
|
applies for the given Tos CoS entry."
|
|
DEFVAL { applyInheritedPriority }
|
|
::= { hpSwitchCosTosConfigEntry 5 }
|
|
|
|
|
|
hpSwitchCosDSCPPolicyConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosDSCPPolicyConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the
|
|
priority applied to each of the Differentiated
|
|
Services Code Points."
|
|
::= { hpSwitchCosConfig 6 }
|
|
|
|
hpSwitchCosDSCPPolicyConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosDSCPPolicyConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A list of objects describing a DiffServe Codepoint
|
|
(DSCP), and the 802.1p priority to apply for that
|
|
DSCP."
|
|
INDEX { hpSwitchCosDSCPPolicyIndex }
|
|
::= { hpSwitchCosDSCPPolicyConfigTable 1 }
|
|
|
|
HpSwitchCosDSCPPolicyConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosDSCPPolicyIndex INTEGER,
|
|
hpSwitchCosDSCPPolicyPriority INTEGER,
|
|
hpSwitchCosDSCPPolicyName OCTET STRING
|
|
}
|
|
|
|
hpSwitchCosDSCPPolicyIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..64)
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An index to uniquely identify each row in the
|
|
hpSwitchCosDSCPPolicyConfigTable."
|
|
::= { hpSwitchCosDSCPPolicyConfigEntry 1 }
|
|
|
|
hpSwitchCosDSCPPolicyPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority value to assign to packets
|
|
with a given DSCP. This value will be inserted in
|
|
the 802.1Q tag and the packet will be placed in the
|
|
appropriate outbound port queue. The value of 255
|
|
is used to indicate no override of the incoming
|
|
priority."
|
|
::= { hpSwitchCosDSCPPolicyConfigEntry 2 }
|
|
|
|
hpSwitchCosDSCPPolicyName OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE(0..32))
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "A user settable name describing a DSCP policy
|
|
table entry."
|
|
::= { hpSwitchCosDSCPPolicyConfigEntry 3 }
|
|
|
|
|
|
hpSwitchCosAppTypeConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchCosAppTypeConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS
|
|
Application type configurations on the switch. An
|
|
application is determined by its network source
|
|
and/or destination port number."
|
|
::= { hpSwitchCosConfig 7 }
|
|
|
|
hpSwitchCosAppTypeConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchCosAppTypeConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An entry in the switch
|
|
hpSwitchCosAppTypeConfigEntry Table."
|
|
INDEX { hpSwitchCosAppTypeConfigIndex }
|
|
::= { hpSwitchCosAppTypeConfigTable 1 }
|
|
|
|
HpSwitchCosAppTypeConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchCosAppTypeConfigIndex INTEGER,
|
|
hpSwitchCosAppTypeConfigType INTEGER,
|
|
hpSwitchCosAppTypeSrcPort INTEGER,
|
|
hpSwitchCosAppTypeDestPort INTEGER,
|
|
hpSwitchCosAppTypePriority INTEGER,
|
|
hpSwitchCosAppTypeDSCPPolicy INTEGER,
|
|
hpSwitchCosAppTypeResolvedPriority INTEGER,
|
|
hpSwitchCosAppTypeApplyPolicy INTEGER,
|
|
hpSwitchCosAppTypeStatus RowStatus,
|
|
hpSwitchCosAppTypeMaxSrcPort INTEGER,
|
|
hpSwitchCosAppTypeMaxDestPort INTEGER
|
|
}
|
|
|
|
hpSwitchCosAppTypeConfigIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An index to uniquely identify this
|
|
hpSwitchCosAppType row."
|
|
::= { hpSwitchCosAppTypeConfigEntry 1 }
|
|
|
|
hpSwitchCosAppTypeConfigType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
udpSrcPortConfig(1),
|
|
udpDestPortConfig(2),
|
|
udpBothPortsConfig(3),
|
|
tcpSrcPortConfig(4),
|
|
tcpDestPortConfig(5),
|
|
tcpBothPortsConfig(6)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This signifies which network port number to apply
|
|
to the given CoS Application policy."
|
|
::= { hpSwitchCosAppTypeConfigEntry 2 }
|
|
|
|
hpSwitchCosAppTypeSrcPort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object represents the source network port
|
|
that this policy applies to."
|
|
::= { hpSwitchCosAppTypeConfigEntry 3 }
|
|
|
|
hpSwitchCosAppTypeDestPort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object represents the destination network
|
|
port that this policy applies to."
|
|
::= { hpSwitchCosAppTypeConfigEntry 4 }
|
|
|
|
hpSwitchCosAppTypePriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that should be applied to
|
|
packets containing the particular configured source
|
|
and/or destination port number in this entry. A
|
|
value of 255 represents that no priority override
|
|
should take place."
|
|
::= { hpSwitchCosAppTypeConfigEntry 5 }
|
|
|
|
hpSwitchCosAppTypeDSCPPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER (1..255)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The DSCP Policy to assign to packets received for
|
|
the specified application. This is an index into
|
|
the hpSwitchCosDSCPPolicy table, or the value 255
|
|
indicating no DSCP Policy exists. This policy is
|
|
associated with an 802.1p priority value, which
|
|
will be inserted in the 802.1Q tag and will cause
|
|
the packet to be placed in the appropriate outbound
|
|
port queue. The DSCP policy value (a
|
|
Differentiated Services codepoint) will also be
|
|
written into the Differentiated-Services field of
|
|
the IP Type-of-Service byte. The value of 255 is
|
|
used to indicate No Override."
|
|
::= { hpSwitchCosAppTypeConfigEntry 6 }
|
|
|
|
hpSwitchCosAppTypeResolvedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..7 | 255)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The 802.1p priority that will be applied to
|
|
packets received on the specified application.
|
|
This value represents the actual operating value
|
|
for this CoS application entry. A value of 255
|
|
represents no override of the incoming priority"
|
|
::= { hpSwitchCosAppTypeConfigEntry 7 }
|
|
|
|
hpSwitchCosAppTypeApplyPolicy OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
applyHpSwitchCosAppTypePriority(1),
|
|
applyHpSwitchCosAppTypeDSCPPolicy(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object determines which configuration policy,
|
|
hpSwitchCosAppTypePriority or
|
|
hpSwitchCosAppTypeDSCPPolicy, applies for the given
|
|
AppType CoS entry. These configuration policies
|
|
are mutually exclusive of one another."
|
|
DEFVAL { applyHpSwitchCosAppTypePriority }
|
|
::= { hpSwitchCosAppTypeConfigEntry 8 }
|
|
|
|
hpSwitchCosAppTypeStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object is used to create and delete in the
|
|
hpSwitchCosAppType table."
|
|
::= { hpSwitchCosAppTypeConfigEntry 9 }
|
|
|
|
hpSwitchCosAppTypeMaxSrcPort OBJECT-TYPE
|
|
SYNTAX INTEGER (0..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object represents the maximum source network
|
|
port that this policy applies to. If a single,
|
|
specific port is being used and not a range, then
|
|
value of this object is zero."
|
|
::= { hpSwitchCosAppTypeConfigEntry 10 }
|
|
|
|
hpSwitchCosAppTypeMaxDestPort OBJECT-TYPE
|
|
SYNTAX INTEGER (0..65535)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This object represents the maximum destination
|
|
network port that this policy applies to. If a
|
|
single, specific port is being used and not a range,
|
|
then value of this object is zero."
|
|
::= { hpSwitchCosAppTypeConfigEntry 11 }
|
|
|
|
|
|
hpSwitchCosLastChange OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The value of the agent's sysUptime when the last
|
|
time this device experienced a change in the
|
|
Class of Service configuration."
|
|
::= { hpSwitchCosConfig 8 }
|
|
|
|
hpSwitchConfigCosLastConfigError OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
aclQosNoError(1),
|
|
aclQosTooManyRulesError(2),
|
|
aclQosTooManyMasksError(3)
|
|
}
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The type of the last QoS
|
|
configuration result or error.
|
|
This object is updated for each
|
|
new QoS configuration. It is
|
|
reset upon reboot."
|
|
::= { hpSwitchCosConfig 9 }
|
|
|
|
hpSwitchMeshConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 18 }
|
|
|
|
hpSwitchMeshMulticastAgingMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
aging(1),
|
|
nonaging(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "With meshing active, a value of aging will cause
|
|
learned multicast addresses to be aged out within
|
|
the required address aging interval. A setting of
|
|
nonaging will prevent learned multicast addresses
|
|
from being removed from the switch. Multicast addresses
|
|
learned while in nonaging mode are not removed until
|
|
the switch is rebooted."
|
|
::= { hpSwitchMeshConfig 1 }
|
|
|
|
hpSwitchMeshBackwardCompatibility OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Due to some hardware differences, the Series
|
|
1600/24xx/4000/8000 switches cannot be used
|
|
directly in a mesh environment with Series 5300XL
|
|
switches. Series 5300XL switches need to emulate
|
|
the operation of Series 1600/24xx/4000/8000
|
|
switches in order to have a heterogeneous mesh
|
|
working properly. Meshing backward-compatibility
|
|
feature allows Series 5300XL switches to operate in
|
|
a compatible mode in which the operation of Series
|
|
1600/24xx/4000/8000 switches are emulated. When
|
|
backward-compatibility is enabled, meshing software
|
|
will establish connections with Series
|
|
1600/24xx/4000/8000 switches and emulate their
|
|
operation. When backward-compatibility disabled,
|
|
Series 1600/24xx/4000/8000 switches in the mesh
|
|
will be ignored by the Series 5300XL switches."
|
|
::= { hpSwitchMeshConfig 2 }
|
|
|
|
|
|
hpSwitchPortIsolationConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 19 }
|
|
|
|
hpSwitchPortIsolationMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This enables the port isolation feature on the device.
|
|
Note: Enabling this feature may require VLANS to be
|
|
configured properly."
|
|
::= { hpSwitchPortIsolationConfig 1 }
|
|
|
|
hpSwitchPortIsolationConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchPortIsolationConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the CoS
|
|
Application type configurations on the switch. An
|
|
application is determined by its network source
|
|
and/or destination port number."
|
|
::= { hpSwitchPortIsolationConfig 2 }
|
|
|
|
hpSwitchPortIsolationConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchPortIsolationConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An entry in the switch
|
|
hpSwitchPortIsolationConfigEntry Table."
|
|
INDEX { hpSwitchPortIsolationPort }
|
|
::= { hpSwitchPortIsolationConfigTable 1 }
|
|
|
|
HpSwitchPortIsolationConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchPortIsolationPort INTEGER,
|
|
hpSwitchPortIsolationPortMode INTEGER
|
|
}
|
|
|
|
hpSwitchPortIsolationPort OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "An entry in the IfIndex table representing a logical port
|
|
on this switch."
|
|
::= { hpSwitchPortIsolationConfigEntry 1 }
|
|
|
|
hpSwitchPortIsolationPortMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
uplink(1),
|
|
public(2),
|
|
private(3),
|
|
local(4),
|
|
group1(5),
|
|
group2(6)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Defines the operational mode of a port when Port
|
|
Isolation feature is enabled."
|
|
::= { hpSwitchPortIsolationConfigEntry 2 }
|
|
|
|
hpSwitchSshConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 20 }
|
|
|
|
hpSwitchSshAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The status of the SSH operation."
|
|
::= { hpSwitchSshConfig 1 }
|
|
|
|
hpSwitchSshVersion OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
version1(1),
|
|
version2(2),
|
|
version1or2(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The version of the SSH protocol to run.
|
|
'version1' will accept connections from
|
|
v1.3 or v1.5 clients. 'version2' will accept
|
|
connections only from v2.0 clients.
|
|
The default is 'version1_or_2' which will accept any
|
|
connection which can be successfully negotiated."
|
|
DEFVAL { 1 }
|
|
::= { hpSwitchSshConfig 2 }
|
|
|
|
hpSwitchSshTimeout OBJECT-TYPE
|
|
SYNTAX Timeout (5..120)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum length of time (in seconds) between the wakeup
|
|
of SSH task and successful protocol negotiation and
|
|
authentication. The default is 120 seconds."
|
|
DEFVAL { 120 }
|
|
::= { hpSwitchSshConfig 3 }
|
|
|
|
hpSwitchSshPortNumber OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The port number on which SSH daemon should listen for
|
|
connection requests."
|
|
DEFVAL { 22 }
|
|
::= { hpSwitchSshConfig 4 }
|
|
|
|
hpSwitchSshServerKeySize OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
bits512(1),
|
|
bits768(2),
|
|
bits1024(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Specifies the key size (in bits) of version 1 SSH host
|
|
rsa key"
|
|
::= { hpSwitchSshConfig 5 }
|
|
|
|
hpSwitchSshFileServerAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable(1),
|
|
disable(2)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Specifies whether or not the SSH daemon will accept
|
|
and process file transfer requests."
|
|
::= { hpSwitchSshConfig 6 }
|
|
|
|
hpSwitchSshIpVersion OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ipv4(1),
|
|
ipv6(2),
|
|
ipv4or6(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The types of IP connections SSH will support.
|
|
'ipv4' will accept connections from
|
|
Ipv4 clients. 'ipv6' will accept
|
|
connections only from ipv6 clients.
|
|
The default is 'ipv4or6' which will accept
|
|
Connections from both ipv4 and ipv6 clients."
|
|
DEFVAL { 3 }
|
|
::= { hpSwitchSshConfig 7 }
|
|
|
|
hpSwitchPendingConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 21 }
|
|
|
|
hpSwitchPendingConfigControl OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
applyMstp(1),
|
|
resetMstp(2),
|
|
noAction(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The object controls switch pending configuration.
|
|
If set to the 'applyMstp' value the object applies
|
|
pending Multiple Spanning Tree Protocol (MSTP)
|
|
configuration. The 'resetMstp' value, if set, triggers
|
|
copying of the active MSTP configuration to the
|
|
pending one. Before the pending configuration is applied
|
|
its consistency is verified and the request fails if
|
|
errors are detected.
|
|
The value the object returns is undefined."
|
|
::= { hpSwitchPendingConfig 1 }
|
|
|
|
hpSwitchBWMinConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 22 }
|
|
|
|
hpSwitchBWMinEgressPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchBWMinEgressPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
A table that contains information about the port's
|
|
egress Guaranteed Minimum Bandwidth configurations
|
|
on this switch."
|
|
::= { hpSwitchBWMinConfig 1 }
|
|
|
|
hpSwitchBWMinEgressPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchBWMinEgressPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The information associated with each port's egress
|
|
Guaranteed Minimum Bandwidth configuration."
|
|
INDEX { hpSwitchBWMinEgressPortIndex }
|
|
::= { hpSwitchBWMinEgressPortConfigTable 1 }
|
|
|
|
HpSwitchBWMinEgressPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchBWMinEgressPortIndex INTEGER,
|
|
hpSwitchBWMinEgressPortPrctLowPriority INTEGER,
|
|
hpSwitchBWMinEgressPortPrctNormalPriority INTEGER,
|
|
hpSwitchBWMinEgressPortPrctMedPriority INTEGER,
|
|
hpSwitchBWMinEgressPortPrctHighPriority INTEGER
|
|
}
|
|
|
|
hpSwitchBWMinEgressPortIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The ifIndex value which uniquely identifies a row
|
|
in the Interfaces Table."
|
|
::= { hpSwitchBWMinEgressPortConfigEntry 1 }
|
|
|
|
hpSwitchBWMinEgressPortPrctLowPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The percentage of Guaranteed Minimum bandwidth to
|
|
be assigned to the egress Low-Priority queue for
|
|
this port. Total values for all four queues must not
|
|
exceed 100 percent."
|
|
::= { hpSwitchBWMinEgressPortConfigEntry 2 }
|
|
|
|
hpSwitchBWMinEgressPortPrctNormalPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The percentage of Guaranteed Minimum bandwidth to
|
|
be assigned to the egress Normal-Priority queue for
|
|
this port. Total values for all four queues must not
|
|
exceed 100 percent."
|
|
::= { hpSwitchBWMinEgressPortConfigEntry 3 }
|
|
|
|
hpSwitchBWMinEgressPortPrctMedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The percentage of Guaranteed Minimum bandwidth to
|
|
be assigned to the egress Medium-Priority queue for
|
|
this port. Total values for all four queues must not
|
|
exceed 100 percent."
|
|
::= { hpSwitchBWMinEgressPortConfigEntry 4 }
|
|
|
|
hpSwitchBWMinEgressPortPrctHighPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "New definitions under HP-ICF-RATE-LIMIT-MIB.
|
|
The percentage of Guaranteed Minimum bandwidth to
|
|
be assigned to the egress High-Priority queue for
|
|
this port. Total values for all four queues must not
|
|
exceed 100 percent."
|
|
::= { hpSwitchBWMinEgressPortConfigEntry 5 }
|
|
|
|
hpSwitchRateLimitPortConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 23 }
|
|
|
|
hpSwitchRateLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpSwitchRateLimitPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "A table that contains information about the port
|
|
Rate-Limiting configurations on this switch."
|
|
::= { hpSwitchRateLimitPortConfig 1 }
|
|
|
|
hpSwitchRateLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpSwitchRateLimitPortConfigEntry
|
|
ACCESS not-accessible
|
|
STATUS mandatory
|
|
DESCRIPTION "The information associated with each port's
|
|
Rate-Limiting configuration."
|
|
INDEX { hpSwitchRateLimitPortIndex }
|
|
::= { hpSwitchRateLimitPortConfigTable 1 }
|
|
|
|
HpSwitchRateLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpSwitchRateLimitPortIndex INTEGER,
|
|
hpSwitchRateLimitPortControlMode INTEGER,
|
|
hpSwitchRateLimitPortSingleControlPrct INTEGER,
|
|
hpSwitchRateLimitPortPrctLowPriority INTEGER,
|
|
hpSwitchRateLimitPortPrctNormalPriority INTEGER,
|
|
hpSwitchRateLimitPortPrctMedPriority INTEGER,
|
|
hpSwitchRateLimitPortPrctHighPriority INTEGER
|
|
}
|
|
|
|
hpSwitchRateLimitPortIndex OBJECT-TYPE
|
|
SYNTAX INTEGER (1..65535)
|
|
ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row
|
|
in the Interfaces Table."
|
|
::= { hpSwitchRateLimitPortConfigEntry 1 }
|
|
|
|
hpSwitchRateLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
rateLimitPerPortOnly(2),
|
|
rateLimitPerQueue(3)
|
|
}
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The mode by which this port will be Rate-Limited
|
|
on ingress. If rateLimitPerPortOnly is configured,
|
|
there will be a single maximum rate for the entire
|
|
port. If rateLimitPerQueue is configured, the values
|
|
for each of the four queues indicate the maximum
|
|
percentage of port traffic that may be received by
|
|
that queue (the sum of these values must not exceed
|
|
100). When rate-limiting is disabled, there are no
|
|
maximum controls on ingress for this port."
|
|
::= { hpSwitchRateLimitPortConfigEntry 2 }
|
|
|
|
hpSwitchRateLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "When hpSwitchRateLimitPortControlMode is configured
|
|
for rateLimitPerPortOnly, this value is the maximum
|
|
percentage of traffic that may be received by this
|
|
port on ingress."
|
|
::= { hpSwitchRateLimitPortConfigEntry 3 }
|
|
|
|
hpSwitchRateLimitPortPrctLowPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
received by this port's Low-Priority queue on ingress.
|
|
hpSwitchRateLimitPortControlMode must be configured to
|
|
use rateLimitPerQueue for this to take effect. A value
|
|
of 0-percent for any queue means that no traffic will
|
|
ever be received on this port for that ingress queue.
|
|
Total values for all four queues must not exceed 100
|
|
percent."
|
|
::= { hpSwitchRateLimitPortConfigEntry 4 }
|
|
|
|
hpSwitchRateLimitPortPrctNormalPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
received by this port's Normal-Priority queue on
|
|
ingress. hpSwitchRateLimitPortControlMode must be
|
|
configured to use rateLimitPerQueue for this to take
|
|
effect. A value of 0-percent for any queue means that
|
|
no traffic will ever be received on this port for that
|
|
ingress queue. Total values for all four queues must
|
|
not exceed 100 percent."
|
|
::= { hpSwitchRateLimitPortConfigEntry 5 }
|
|
|
|
hpSwitchRateLimitPortPrctMedPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
received by this port's Medium-Priority queue on
|
|
ingress. hpSwitchRateLimitPortControlMode must be
|
|
configured to use rateLimitPerQueue for this to take
|
|
effect. A value of 0-percent for any queue means that
|
|
no traffic will ever be received on this port for that
|
|
ingress queue. Total values for all four queues must
|
|
not exceed 100 percent."
|
|
::= { hpSwitchRateLimitPortConfigEntry 6 }
|
|
|
|
hpSwitchRateLimitPortPrctHighPriority OBJECT-TYPE
|
|
SYNTAX INTEGER (0..100)
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
received by this port's High-Priority queue on
|
|
ingress. hpSwitchRateLimitPortControlMode must be
|
|
configured to use rateLimitPerQueue for this to take
|
|
effect. A value of 0-percent for any queue means that
|
|
no traffic will ever be received on this port for that
|
|
ingress queue. Total values for all four queues must
|
|
not exceed 100 percent."
|
|
::= { hpSwitchRateLimitPortConfigEntry 7 }
|
|
|
|
hpSwitchQosPassThroughMode OBJECT IDENTIFIER ::= { hpSwitchConfig 24 }
|
|
|
|
hpSwitchQosPassThroughModeConfig OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
optimized (1),
|
|
typical (2),
|
|
balanced (3),
|
|
onequeue (4)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Specify the queue configuration mode for the switch.
|
|
While changing the queue configuration mode this feature
|
|
momentarily require to bring down the logical port and
|
|
after the initialisation of the queues the ports are
|
|
brought up."
|
|
|
|
::= { hpSwitchQosPassThroughMode 1 }
|
|
|
|
hpSwitchReboot OBJECT IDENTIFIER ::= { hpSwitchConfig 25 }
|
|
|
|
hpSwitchRebootConfig OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
yes (1),
|
|
no (2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS mandatory
|
|
DESCRIPTION "This tells the status of the switch whether it requires
|
|
reboot for some variable to get effective.
|
|
The value of this variable can be
|
|
|
|
yes (1) reboot is required.
|
|
no (2) reboot is not required."
|
|
::= { hpSwitchReboot 1 }
|
|
|
|
hpSwitchRebootFastBoot OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enable (1),
|
|
disable (2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "Specifies whether fastboot is enabled or not on
|
|
the switch."
|
|
DEFVAL { disable }
|
|
|
|
::= { hpSwitchReboot 2 }
|
|
|
|
|
|
hpSwitchProtectedPortsConfig OBJECT IDENTIFIER ::= { hpSwitchConfig 26 }
|
|
|
|
hpSwitchProtectedPortsMask OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
ACCESS read-write
|
|
STATUS mandatory
|
|
DESCRIPTION "This variable specifies a group of ports that are not
|
|
allowed to communicate to each-other. Each octet within
|
|
the value of this object specifies a set of eight ports,
|
|
with the first octet specifying ports 1 through 8, the
|
|
second octet specifying ports 9 through 16, etc.
|
|
Within each octet, the most significant bit represents
|
|
the lowest numbered port, and the least significant bit
|
|
represents the highest numbered port. Thus, each port
|
|
of the switch is represented by a single bit within
|
|
the value of this object."
|
|
::= { hpSwitchProtectedPortsConfig 1 }
|
|
|
|
|
|
-- **********************************************************
|
|
-- Trap Definitions
|
|
-- **********************************************************
|
|
|
|
hpSwitchTraps OBJECT IDENTIFIER ::= { hpSwitchConfig 0 }
|
|
|
|
hpSwitchTrapsObjects
|
|
OBJECT IDENTIFIER ::= { hpSwitchTraps 1 }
|
|
|
|
hpSwitchStpErrantBpduDetector OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
bpduFilter (1),
|
|
bpduProtection (2),
|
|
pvstFilter (3),
|
|
pvstProtection (4)
|
|
}
|
|
ACCESS accessible-for-notify
|
|
STATUS optional
|
|
DESCRIPTION "The identifier of the feature generating Errant
|
|
BPDU trap."
|
|
::= { hpSwitchTrapsObjects 1 }
|
|
|
|
hpSwitchStpErrantBpduSrcMac OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
ACCESS accessible-for-notify
|
|
STATUS optional
|
|
DESCRIPTION "The source MAC address of the port sending Errant
|
|
STP BPDU."
|
|
::= { hpSwitchTrapsObjects 2 }
|
|
|
|
hpSwitchStpErrantBpduReceived TRAP-TYPE
|
|
ENTERPRISE hpSwitchTraps
|
|
VARIABLES { hpSwitchStpPort,
|
|
hpSwitchStpPortErrantBpduCounter,
|
|
dot1dStpPortState,
|
|
dot1dStpPortDesignatedBridge,
|
|
dot1dStpPortDesignatedPort,
|
|
hpSwitchStpErrantBpduSrcMac,
|
|
hpSwitchStpErrantBpduDetector }
|
|
DESCRIPTION "This trap indicates that unexpected (errant) STP BPDU
|
|
has been received on a port (e.g. on a port that is
|
|
connected to non-STP device). This notification trap
|
|
is controlled by the state of 'hpSwitchStpTrapCntl'
|
|
object. Implementation of this trap is optional."
|
|
::= 1
|
|
END
|