Initial commitHEADmain

1 files changed, 1289 insertions, 0 deletions

diff --git a/MIBS/DIAL-CONTROL-MIB b/MIBS/DIAL-CONTROL-MIB
new file mode 100644
index 0000000..db466b9
--- /dev/null
+++ b/MIBS/DIAL-CONTROL-MIB
@@ -0,0 +1,1289 @@
+-- *****************************************************************
+-- One line description here.
+--
+-- Bibek Das, January 1997
+--
+-- Copyright (c) 1997-1998 by cisco Systems, Inc.
+-- All rights reserved.
+-- *****************************************************************
+--
+-- This mib was extracted from RFC 2128
+
+
+DIAL-CONTROL-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+        MODULE-IDENTITY,
+        NOTIFICATION-TYPE,
+        OBJECT-TYPE,
+	Gauge32
+                FROM SNMPv2-SMI
+        TEXTUAL-CONVENTION,
+        DisplayString,
+        TimeStamp,
+        RowStatus
+                 FROM SNMPv2-TC
+        MODULE-COMPLIANCE,
+        OBJECT-GROUP
+                FROM SNMPv2-CONF
+        IANAifType
+                FROM IANAifType-MIB
+        ifOperStatus,
+        ifIndex,
+        InterfaceIndex,
+        InterfaceIndexOrZero
+                FROM IF-MIB
+        transmission
+                FROM RFC1213-MIB;
+
+dialControlMib MODULE-IDENTITY
+        LAST-UPDATED    "9609231544Z" -- Sep 23, 1996
+        ORGANIZATION    "IETF ISDN Working Group"
+        CONTACT-INFO
+            "        Guenter Roeck
+             Postal: cisco Systems
+                     170 West Tasman Drive
+                     San Jose, CA 95134
+                     U.S.A.
+             Phone:  +1 408 527 3143
+             E-mail: groeck@cisco.com"
+        DESCRIPTION
+            "The MIB module to describe peer information for
+             demand access and possibly other kinds of interfaces."
+        ::= { transmission 21 }
+
+AbsoluteCounter32 ::= TEXTUAL-CONVENTION
+        STATUS      current
+        DESCRIPTION
+            "Represents a Counter32-like value that starts at zero,
+             does not decrease, and does not wrap. This may be used
+             only in situations where wrapping is not possible or
+             extremely unlikely. Should such a counter overflow,
+             it locks at the maxium value of 4,294,967,295.
+
+             The primary use of this type of counter is situations
+             where a counter value is to be recorded as history
+             and is thus no longer subject to reading for changing
+             values."
+        SYNTAX      Gauge32
+
+-- Dial Control Mib objects definitions
+
+dialControlMibObjects OBJECT IDENTIFIER ::= { dialControlMib 1 }
+
+-- General configuration group
+
+dialCtlConfiguration OBJECT IDENTIFIER ::= { dialControlMibObjects 1 }
+
+-- general configuration data/parameters
+
+dialCtlAcceptMode OBJECT-TYPE
+        SYNTAX INTEGER {
+            acceptNone(1),
+            acceptAll(2),
+            acceptKnown(3)
+        }
+        MAX-ACCESS  read-write
+        STATUS      current
+        DESCRIPTION
+            "The security level for acceptance of incoming calls.
+             acceptNone(1)  - incoming calls will not be accepted
+             acceptAll(2)   - incoming calls will be accepted,
+                              even if there is no matching entry
+                              in the dialCtlPeerCfgTable
+             acceptKnown(3) - incoming calls will be accepted only
+                              if there is a matching entry in the
+                              dialCtlPeerCfgTable
+            "
+        ::= { dialCtlConfiguration 1 }
+
+dialCtlTrapEnable OBJECT-TYPE
+        SYNTAX      INTEGER {
+            enabled(1),
+            disabled(2)
+        }
+        MAX-ACCESS  read-write
+        STATUS      current
+        DESCRIPTION
+            "This object indicates whether dialCtlPeerCallInformation
+             and dialCtlPeerCallSetup traps should be generated for
+             all peers. If the value of this object is enabled(1),
+             traps will be generated for all peers. If the value
+             of this object is disabled(2), traps will be generated
+             only for peers having dialCtlPeerCfgTrapEnable set
+             to enabled(1)."
+        DEFVAL      { disabled }
+        ::= { dialCtlConfiguration 2 }
+
+
+-- Peer group
+
+dialCtlPeer OBJECT IDENTIFIER ::= { dialControlMibObjects 2 }
+
+-- peer configuration table
+
+dialCtlPeerCfgTable OBJECT-TYPE
+        SYNTAX      SEQUENCE OF DialCtlPeerCfgEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "The list of peers from which the managed device
+             will accept calls or to which it will place them."
+       ::= { dialCtlPeer 1 }
+
+dialCtlPeerCfgEntry OBJECT-TYPE
+        SYNTAX      DialCtlPeerCfgEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "Configuration data for a single Peer. This entry is
+             effectively permanent, and contains information
+             to identify the peer, how to connect to the peer,
+             how to identify the peer and its permissions.
+             The value of dialCtlPeerCfgOriginateAddress must be
+             specified before a new row in this table can become
+             active(1). Any writeable parameters in an existing entry
+             can be modified while the entry is active. The modification
+             will take effect when the peer in question will be
+             called the next time.
+             An entry in this table can only be created if the
+             associated ifEntry already exists."
+        INDEX       { dialCtlPeerCfgId, ifIndex }
+      ::= { dialCtlPeerCfgTable 1 }
+
+DialCtlPeerCfgEntry ::= SEQUENCE {
+            dialCtlPeerCfgId                 INTEGER,
+            dialCtlPeerCfgIfType             IANAifType,
+            dialCtlPeerCfgLowerIf            InterfaceIndexOrZero,
+            dialCtlPeerCfgOriginateAddress   DisplayString,
+            dialCtlPeerCfgAnswerAddress      DisplayString,
+            dialCtlPeerCfgSubAddress         DisplayString,
+            dialCtlPeerCfgClosedUserGroup    DisplayString,
+            dialCtlPeerCfgSpeed              INTEGER,
+            dialCtlPeerCfgInfoType           INTEGER,
+            dialCtlPeerCfgPermission         INTEGER,
+            dialCtlPeerCfgInactivityTimer    INTEGER,
+            dialCtlPeerCfgMinDuration        INTEGER,
+            dialCtlPeerCfgMaxDuration        INTEGER,
+            dialCtlPeerCfgCarrierDelay       INTEGER,
+            dialCtlPeerCfgCallRetries        INTEGER,
+            dialCtlPeerCfgRetryDelay         INTEGER,
+            dialCtlPeerCfgFailureDelay       INTEGER,
+            dialCtlPeerCfgTrapEnable         INTEGER,
+            dialCtlPeerCfgStatus             RowStatus
+        }
+
+dialCtlPeerCfgId OBJECT-TYPE
+        SYNTAX      INTEGER (1..2147483647)
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "This object identifies a single peer. There may
+             be several entries in this table for one peer,
+             defining different ways of reaching this peer.
+             Thus, there may be several entries in this table
+             with the same value of dialCtlPeerCfgId.
+             Multiple entries for one peer may be used to support
+             multilink as well as backup lines.
+             A single peer will be identified by a unique value
+             of this object. Several entries for one peer MUST
+             have the same value of dialCtlPeerCfgId, but different
+             ifEntries and thus different values of ifIndex."
+        ::= { dialCtlPeerCfgEntry 1 }
+
+dialCtlPeerCfgIfType OBJECT-TYPE
+        SYNTAX      IANAifType
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The interface type to be used for calling this peer.
+             In case of ISDN, the value of isdn(63) is to be used."
+        DEFVAL      { other }
+        ::= { dialCtlPeerCfgEntry 2 }
+
+dialCtlPeerCfgLowerIf OBJECT-TYPE
+        SYNTAX      InterfaceIndexOrZero
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "ifIndex value of an interface the peer will have to be
+             called on. For example, on an ISDN interface, this can be
+             the ifIndex value of a D channel or the ifIndex value of a
+             B channel, whatever is appropriate for a given peer.
+             As an example, for Basic Rate leased lines it will be
+             necessary to specify a B channel ifIndex, while for
+
+
+
+
+             semi-permanent connections the D channel ifIndex has
+             to be specified.
+             If the interface can be dynamically assigned, this object
+             has a value of zero."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 3 }
+
+dialCtlPeerCfgOriginateAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Call Address at which the peer will be called.
+             Think of this as the set of characters following 'ATDT '
+             or the 'phone number' included in a D channel call request.
+
+             The structure of this information will be switch type
+             specific. If there is no address information required
+             for reaching the peer, i.e., for leased lines,
+             this object will be a zero length string."
+        ::= { dialCtlPeerCfgEntry 4 }
+
+dialCtlPeerCfgAnswerAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Calling Party Number information element, as for example
+             passed in an ISDN SETUP message by a PBX or switch,
+             for incoming calls.
+             This address can be used to identify the peer.
+             If this address is either unknown or identical
+             to dialCtlPeerCfgOriginateAddress, this object will be
+             a zero length string."
+        DEFVAL      { "" }
+        ::= { dialCtlPeerCfgEntry 5 }
+
+dialCtlPeerCfgSubAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Subaddress at which the peer will be called.
+             If the subaddress is undefined for the given media or
+             unused, this is a zero length string."
+        DEFVAL      { "" }
+        ::= { dialCtlPeerCfgEntry 6 }
+
+dialCtlPeerCfgClosedUserGroup OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Closed User Group at which the peer will be called.
+             If the Closed User Group is undefined for the given media
+             or unused, this is a zero length string."
+        REFERENCE
+            "Q.931, chapter 4.6.1."
+        DEFVAL      { "" }
+        ::= { dialCtlPeerCfgEntry 7 }
+
+dialCtlPeerCfgSpeed OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The desired information transfer speed in bits/second
+             when calling this peer.
+             The detailed media specific information, e.g. information
+             type and information transfer rate for ISDN circuits,
+             has to be extracted from this object.
+             If the transfer speed to be used is unknown or the default
+             speed for this type of interfaces, the value of this object
+             may be zero."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 8 }
+
+dialCtlPeerCfgInfoType OBJECT-TYPE
+        SYNTAX      INTEGER {
+            other(1),
+            speech(2),
+            unrestrictedDigital(3),     -- 64k/s data
+            unrestrictedDigital56(4),   -- with 56k rate adaption
+            restrictedDigital(5),
+            audio31(6),                 -- 3.1 kHz audio
+            audio7(7),                  -- 7 kHz audio
+            video(8),
+            packetSwitched(9),
+            fax(10)
+        }
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The Information Transfer Capability to be used when
+             calling this peer.
+
+             speech(2) refers to a non-data connection, whereas
+             audio31(6) and audio7(7) refer to data mode
+             connections."
+        DEFVAL      { other }
+        ::= { dialCtlPeerCfgEntry 9 }
+
+dialCtlPeerCfgPermission OBJECT-TYPE
+        SYNTAX      INTEGER {
+            originate(1),
+            answer(2),
+            both(3),               -- both originate & answer
+            callback(4),
+            none(5)
+        }
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Applicable permissions. callback(4) either rejects the
+             call and then calls back, or uses the 'Reverse charging'
+             information element if it is available.
+             Note that callback(4) is supposed to control charging, not
+             security, and applies to callback prior to accepting a
+             call. Callback for security reasons can be handled using
+             PPP callback."
+        DEFVAL      { both }
+        ::= { dialCtlPeerCfgEntry 10 }
+
+dialCtlPeerCfgInactivityTimer OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        UNITS       "seconds"
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The connection will be automatically disconnected
+             if no longer carrying useful data for a time
+             period, in seconds, specified in this object.
+             Useful data in this context refers to forwarding
+             packets, including routing information; it
+             excludes the encapsulator maintenance frames.
+             A value of zero means the connection will not be
+             automatically taken down due to inactivity,
+             which implies that it is a dedicated circuit."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 11 }
+
+dialCtlPeerCfgMinDuration OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Minimum duration of a call in seconds, starting from the
+             time the call is connected until the call is disconnected.
+             This is to accomplish the fact that in most countries
+             charging applies to units of time, which should be matched
+             as closely as possible."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 12 }
+
+dialCtlPeerCfgMaxDuration OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Maximum call duration in seconds. Zero means 'unlimited'."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 13 }
+
+dialCtlPeerCfgCarrierDelay OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        UNITS       "seconds"
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The call timeout time in seconds. The default value
+             of zero means that the call timeout as specified for
+             the media in question will apply."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 14 }
+
+dialCtlPeerCfgCallRetries OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The number of calls to a non-responding address
+             that may be made. A retry count of zero means
+             there is no bound. The intent is to bound
+             the number of successive calls to an address
+             which is inaccessible, or which refuses those calls.
+
+             Some countries regulate the number of call retries
+             to a given peer that can be made."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 15 }
+
+dialCtlPeerCfgRetryDelay OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        UNITS       "seconds"
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The time in seconds between call retries if a peer
+             cannot be reached.
+             A value of zero means that call retries may be done
+             without any delay."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 16 }
+
+dialCtlPeerCfgFailureDelay OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        UNITS       "seconds"
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "The time in seconds after which call attempts are
+             to be placed again after a peer has been noticed
+             to be unreachable, i.e. after dialCtlPeerCfgCallRetries
+             unsuccessful call attempts.
+             A value of zero means that a peer will not be called
+             again after dialCtlPeerCfgCallRetries unsuccessful call
+             attempts."
+        DEFVAL      { 0 }
+        ::= { dialCtlPeerCfgEntry 17 }
+
+dialCtlPeerCfgTrapEnable OBJECT-TYPE
+        SYNTAX      INTEGER {
+            enabled(1),
+            disabled(2)
+        }
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "This object indicates whether dialCtlPeerCallInformation
+             and dialCtlPeerCallSetup traps should be generated for
+             this peer."
+        DEFVAL      { disabled }
+        ::= { dialCtlPeerCfgEntry 18 }
+
+dialCtlPeerCfgStatus OBJECT-TYPE
+        SYNTAX      RowStatus
+        MAX-ACCESS  read-create
+        STATUS      current
+        DESCRIPTION
+            "Status of one row in this table."
+        ::= { dialCtlPeerCfgEntry 19 }
+
+-- Peer statistics table
+
+dialCtlPeerStatsTable OBJECT-TYPE
+        SYNTAX      SEQUENCE OF DialCtlPeerStatsEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "Statistics information for each peer entry.
+             There will be one entry in this table for each entry
+             in the dialCtlPeerCfgTable."
+       ::= { dialCtlPeer 2 }
+
+dialCtlPeerStatsEntry OBJECT-TYPE
+        SYNTAX      DialCtlPeerStatsEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "Statistics information for a single Peer. This entry
+             is effectively permanent, and contains information
+             describing the last call attempt as well as supplying
+             statistical information."
+        AUGMENTS    { dialCtlPeerCfgEntry }
+      ::= { dialCtlPeerStatsTable 1 }
+
+DialCtlPeerStatsEntry ::=
+        SEQUENCE {
+            dialCtlPeerStatsConnectTime          AbsoluteCounter32,
+            dialCtlPeerStatsChargedUnits         AbsoluteCounter32,
+            dialCtlPeerStatsSuccessCalls         AbsoluteCounter32,
+            dialCtlPeerStatsFailCalls            AbsoluteCounter32,
+            dialCtlPeerStatsAcceptCalls          AbsoluteCounter32,
+            dialCtlPeerStatsRefuseCalls          AbsoluteCounter32,
+            dialCtlPeerStatsLastDisconnectCause  OCTET STRING,
+            dialCtlPeerStatsLastDisconnectText   DisplayString,
+            dialCtlPeerStatsLastSetupTime        TimeStamp
+        }
+
+dialCtlPeerStatsConnectTime OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        UNITS       "seconds"
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "Accumulated connect time to the peer since system startup.
+             This is the total connect time, i.e. the connect time
+             for outgoing calls plus the time for incoming calls."
+        ::= { dialCtlPeerStatsEntry 1 }
+
+dialCtlPeerStatsChargedUnits OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The total number of charging units applying to this
+             peer since system startup.
+             Only the charging units applying to the local interface,
+             i.e. for originated calls or for calls with 'Reverse
+             charging' being active, will be counted here."
+        ::= { dialCtlPeerStatsEntry 2 }
+
+dialCtlPeerStatsSuccessCalls OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "Number of completed calls to this peer."
+        ::= { dialCtlPeerStatsEntry 3 }
+
+dialCtlPeerStatsFailCalls OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "Number of failed call attempts to this peer since system
+             startup."
+        ::= { dialCtlPeerStatsEntry 4 }
+
+dialCtlPeerStatsAcceptCalls OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "Number of calls from this peer accepted since system
+             startup."
+        ::= { dialCtlPeerStatsEntry 5 }
+
+dialCtlPeerStatsRefuseCalls OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "Number of calls from this peer refused since system
+             startup."
+        ::= { dialCtlPeerStatsEntry 6 }
+
+dialCtlPeerStatsLastDisconnectCause OBJECT-TYPE
+        SYNTAX      OCTET STRING (SIZE (0..4))
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The encoded network cause value associated with the last
+             call.
+             This object will be updated whenever a call is started
+             or cleared.
+             The value of this object will depend on the interface type
+             as well as on the protocol and protocol version being
+             used on this interface. Some references for possible cause
+             values are given below."
+        REFERENCE
+            "- Bellcore SR-NWT-001953, Generic Guidelines for
+               ISDN Terminal Equipment On Basic Access Interfaces,
+               chapter 5.2.5.8.
+             - Bellcore SR-NWT-002343, ISDN Primary Rate Interface
+               Generic Guidelines for Customer Premises Equipment,
+               chapter 8.2.5.8.
+             - ITU-T Q.931, Appendix I.
+             - ITU-T X.25, CAUSE and DIAGNOSTIC field values.
+             - German Telekom FTZ 1TR6, chapter 3.2.3.4.4.4."
+        ::= { dialCtlPeerStatsEntry 7 }
+
+dialCtlPeerStatsLastDisconnectText OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "ASCII text describing the reason for the last call
+             termination.
+
+             This object exists because it would be impossible for
+             a management station to store all possible cause values
+             for all types of interfaces. It should be used only if
+             a management station is unable to decode the value of
+             dialCtlPeerStatsLastDisconnectCause.
+
+             This object will be updated whenever a call is started
+             or cleared."
+        ::= { dialCtlPeerStatsEntry 8 }
+
+dialCtlPeerStatsLastSetupTime OBJECT-TYPE
+        SYNTAX      TimeStamp
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The value of sysUpTime when the last call to this peer
+             was started.
+             For ISDN media, this will be the time when the setup
+             message was received from or sent to the network.
+             This object will be updated whenever a call is started
+             or cleared."
+        ::= { dialCtlPeerStatsEntry 9 }
+
+--
+-- the active call group
+--
+
+callActive OBJECT IDENTIFIER ::= { dialControlMibObjects 3 }
+
+-- callActiveTable
+-- Table to store active call information.
+-- These calls could be circuit switched or they could
+-- be virtual circuits.
+-- An entry will be created when a call is started and deleted
+-- when a call is cleared.
+
+callActiveTable OBJECT-TYPE
+        SYNTAX      SEQUENCE OF CallActiveEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "A table containing information about active
+             calls to a specific destination."
+        ::= { callActive 1 }
+
+callActiveEntry OBJECT-TYPE
+        SYNTAX      CallActiveEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "The information regarding a single active Connection.
+             An entry in this table will be created when a call is
+             started. An entry in this table will be deleted when
+             an active call clears."
+        INDEX       { callActiveSetupTime, callActiveIndex }
+        ::= { callActiveTable 1 }
+
+
+CallActiveEntry ::=
+        SEQUENCE {
+            callActiveSetupTime                  TimeStamp,
+            callActiveIndex                      INTEGER,
+            callActivePeerAddress                DisplayString,
+            callActivePeerSubAddress             DisplayString,
+            callActivePeerId                     INTEGER,
+            callActivePeerIfIndex                INTEGER,
+            callActiveLogicalIfIndex             InterfaceIndexOrZero,
+            callActiveConnectTime                TimeStamp,
+            callActiveCallState                  INTEGER,
+            callActiveCallOrigin                 INTEGER,
+            callActiveChargedUnits               AbsoluteCounter32,
+            callActiveInfoType                   INTEGER,
+            callActiveTransmitPackets            AbsoluteCounter32,
+            callActiveTransmitBytes              AbsoluteCounter32,
+            callActiveReceivePackets             AbsoluteCounter32,
+            callActiveReceiveBytes               AbsoluteCounter32
+        }
+
+callActiveSetupTime OBJECT-TYPE
+        SYNTAX      TimeStamp
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "The value of sysUpTime when the call associated to this
+             entry was started. This will be useful for an NMS to
+             retrieve all calls after a specific time. Also, this object
+             can be useful in finding large delays between the time the
+             call was started and the time the call was connected.
+             For ISDN media, this will be the time when the setup
+             message was received from or sent to the network."
+        ::= { callActiveEntry 1 }
+
+callActiveIndex OBJECT-TYPE
+        SYNTAX      INTEGER (1..'7fffffff'h)
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "Small index variable to distinguish calls that start in
+             the same hundredth of a second."
+        ::= { callActiveEntry 2 }
+
+callActivePeerAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number this call is connected to. If the number is
+             not available, then it will have a length of zero."
+        ::= { callActiveEntry 3 }
+
+callActivePeerSubAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The subaddress this call is connected to. If the subaddress
+             is undefined or not available, this will be a zero length
+             string."
+        ::= { callActiveEntry 4 }
+
+callActivePeerId OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the Id value of the peer table entry
+             to which this call was made. If a peer table entry
+             for this call does not exist or is unknown, the value
+             of this object will be zero."
+        ::= { callActiveEntry 5 }
+
+callActivePeerIfIndex OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the ifIndex value of the peer table entry
+             to which this call was made. If a peer table entry
+             for this call does not exist or is unknown, the value
+             of this object will be zero."
+        ::= { callActiveEntry 6 }
+
+callActiveLogicalIfIndex OBJECT-TYPE
+        SYNTAX      InterfaceIndexOrZero
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the ifIndex value of the logical interface through
+             which this call was made. For ISDN media, this would be
+             the ifIndex of the B channel which was used for this call.
+             If the ifIndex value is unknown, the value of this object
+             will be zero."
+        ::= { callActiveEntry 7 }
+
+callActiveConnectTime OBJECT-TYPE
+        SYNTAX      TimeStamp
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The value of sysUpTime when the call was connected.
+             If the call is not connected, this object will have a
+             value of zero."
+        ::= { callActiveEntry 8 }
+
+callActiveCallState OBJECT-TYPE
+        SYNTAX      INTEGER {
+            unknown(1),
+            connecting(2),
+            connected(3),
+            active(4)
+        }
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The current call state.
+             unknown(1)     - The call state is unknown.
+             connecting(2)  - A connection attempt (outgoing call)
+                              is being made.
+             connected(3)   - An incoming call is in the process
+                              of validation.
+             active(4)      - The call is active.
+            "
+        ::= { callActiveEntry 9 }
+
+callActiveCallOrigin OBJECT-TYPE
+        SYNTAX      INTEGER {
+            originate(1),
+            answer(2),
+            callback(3)
+        }
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The call origin."
+        ::= { callActiveEntry 10 }
+
+callActiveChargedUnits OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of charged units for this connection.
+             For incoming calls or if charging information is
+             not supplied by the switch, the value of this object
+             will be zero."
+        ::= { callActiveEntry 11 }
+
+callActiveInfoType OBJECT-TYPE
+        SYNTAX      INTEGER {
+            other(1),                   -- e.g. for non-isdn media
+            speech(2),
+            unrestrictedDigital(3),     -- 64k/s data
+            unrestrictedDigital56(4),   -- with 56k rate adaption
+            restrictedDigital(5),
+            audio31(6),                 -- 3.1 kHz audio
+            audio7(7),                  -- 7 kHz audio
+            video(8),
+            packetSwitched(9),
+            fax(10)
+        }
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The information type for this call."
+        ::= { callActiveEntry 12 }
+
+callActiveTransmitPackets OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS     current
+        DESCRIPTION
+            "The number of packets which were transmitted for this
+             call."
+        ::= { callActiveEntry 13 }
+
+callActiveTransmitBytes OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of bytes which were transmitted for this
+             call."
+        ::= { callActiveEntry 14 }
+
+callActiveReceivePackets OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of packets which were received for this
+             call."
+        ::= { callActiveEntry 15 }
+
+callActiveReceiveBytes OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of bytes which were received for this call."
+        ::= { callActiveEntry 16 }
+
+--
+-- the call history group
+--
+
+callHistory OBJECT IDENTIFIER ::= { dialControlMibObjects 4 }
+
+callHistoryTableMaxLength OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-write
+        STATUS      current
+        DESCRIPTION
+            "The upper limit on the number of entries that the
+             callHistoryTable may contain.  A value of 0
+             will prevent any history from being retained. When
+             this table is full, the oldest entry will be deleted
+             and the new one will be created."
+        ::= { callHistory 1 }
+
+callHistoryRetainTimer OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        UNITS       "minutes"
+        MAX-ACCESS  read-write
+        STATUS      current
+        DESCRIPTION
+            "The minimum amount of time that an callHistoryEntry
+             will be maintained before being deleted. A value of
+             0 will prevent any history from being retained in the
+             callHistoryTable, but will neither prevent callCompletion
+             traps being generated nor affect other tables."
+        ::= { callHistory 2 }
+
+-- callHistoryTable
+-- PLEASE NOTE
+-- PLEASE NOTE
+-- THE FOLLOWING TABLE HAS BEEN REPLACED BY THE CALL HISTORY TABLE
+-- DEFINED IN CISCO-DIAL-CONTROL-MIB.my
+-- PLEASE NOTE
+-- Table to store the past call information. The Destination number
+-- and the call connect and disconnect time, the disconnection cause
+-- are stored. These calls could be circuit switched or they could
+-- be virtual circuits. History of each and every call is stored,
+-- of successful calls as well as of unsuccessful and rejected calls.
+-- An entry will be created when a call is cleared.
+
+callHistoryTable OBJECT-TYPE
+        SYNTAX      SEQUENCE OF CallHistoryEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "A table containing information about specific
+             calls to a specific destination."
+        ::= { callHistory 3 }
+
+callHistoryEntry OBJECT-TYPE
+        SYNTAX      CallHistoryEntry
+        MAX-ACCESS  not-accessible
+        STATUS      current
+        DESCRIPTION
+            "The information regarding a single Connection."
+        INDEX       { callActiveSetupTime, callActiveIndex }
+        ::= { callHistoryTable 1 }
+
+
+CallHistoryEntry ::=
+        SEQUENCE {
+            callHistoryPeerAddress               DisplayString,
+            callHistoryPeerSubAddress            DisplayString,
+            callHistoryPeerId                    INTEGER,
+            callHistoryPeerIfIndex               INTEGER,
+            callHistoryLogicalIfIndex            InterfaceIndex,
+            callHistoryDisconnectCause           OCTET STRING,
+            callHistoryDisconnectText            DisplayString,
+            callHistoryConnectTime               TimeStamp,
+            callHistoryDisconnectTime            TimeStamp,
+            callHistoryCallOrigin                INTEGER,
+            callHistoryChargedUnits              AbsoluteCounter32,
+            callHistoryInfoType                  INTEGER,
+            callHistoryTransmitPackets           AbsoluteCounter32,
+            callHistoryTransmitBytes             AbsoluteCounter32,
+            callHistoryReceivePackets            AbsoluteCounter32,
+            callHistoryReceiveBytes              AbsoluteCounter32
+        }
+
+callHistoryPeerAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number this call was connected to. If the number is
+             not available, then it will have a length of zero."
+        ::= { callHistoryEntry 1 }
+
+callHistoryPeerSubAddress OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The subaddress this call was connected to. If the subaddress
+             is undefined or not available, this will be a zero length
+             string."
+        ::= { callHistoryEntry 2 }
+callHistoryPeerId OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the Id value of the peer table entry
+             to which this call was made. If a peer table entry
+             for this call does not exist, the value of this object
+             will be zero."
+        ::= { callHistoryEntry 3 }
+
+callHistoryPeerIfIndex OBJECT-TYPE
+        SYNTAX      INTEGER (0..2147483647)
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the ifIndex value of the peer table entry
+             to which this call was made. If a peer table entry
+             for this call does not exist, the value of this object
+             will be zero."
+        ::= { callHistoryEntry 4 }
+
+callHistoryLogicalIfIndex OBJECT-TYPE
+        SYNTAX      InterfaceIndex
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "This is the ifIndex value of the logical interface through
+             which this call was made. For ISDN media, this would be
+             the ifIndex of the B channel which was used for this call."
+        ::= { callHistoryEntry 5 }
+
+callHistoryDisconnectCause OBJECT-TYPE
+        SYNTAX      OCTET STRING (SIZE (0..4))
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The encoded network cause value associated with this call.
+
+             The value of this object will depend on the interface type
+             as well as on the protocol and protocol version being
+             used on this interface. Some references for possible cause
+             values are given below."
+        REFERENCE
+            "- Bellcore SR-NWT-001953, Generic Guidelines for
+               ISDN Terminal Equipment On Basic Access Interfaces,
+               chapter 5.2.5.8.
+             - Bellcore SR-NWT-002343, ISDN Primary Rate Interface
+               Generic Guidelines for Customer Premises Equipment,
+               chapter 8.2.5.8.
+             - ITU-T Q.931, Appendix I.
+             - ITU-T X.25, CAUSE and DIAGNOSTIC field values.
+             - German Telekom FTZ 1TR6, chapter 3.2.3.4.4.4."
+        ::= { callHistoryEntry 6 }
+
+callHistoryDisconnectText OBJECT-TYPE
+        SYNTAX      DisplayString
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "ASCII text describing the reason for call termination.
+
+             This object exists because it would be impossible for
+             a management station to store all possible cause values
+             for all types of interfaces. It should be used only if
+             a management station is unable to decode the value of
+             dialCtlPeerStatsLastDisconnectCause."
+        ::= { callHistoryEntry 7 }
+
+callHistoryConnectTime OBJECT-TYPE
+        SYNTAX      TimeStamp
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The value of sysUpTime when the call was connected."
+        ::= { callHistoryEntry 8 }
+
+callHistoryDisconnectTime OBJECT-TYPE
+        SYNTAX      TimeStamp
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The value of sysUpTime when the call was disconnected."
+        ::= { callHistoryEntry 9 }
+
+callHistoryCallOrigin OBJECT-TYPE
+        SYNTAX      INTEGER {
+            originate(1),
+            answer(2),
+            callback(3)
+        }
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The call origin."
+        ::= { callHistoryEntry 10 }
+
+callHistoryChargedUnits OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of charged units for this connection.
+             For incoming calls or if charging information is
+             not supplied by the switch, the value of this object
+             will be zero."
+        ::= { callHistoryEntry 11 }
+
+callHistoryInfoType OBJECT-TYPE
+        SYNTAX      INTEGER {
+            other(1),                   -- e.g. for non-isdn media
+            speech(2),
+            unrestrictedDigital(3),     -- 64k/s data
+            unrestrictedDigital56(4),   -- with 56k rate adaption
+            restrictedDigital(5),
+            audio31(6),                 -- 3.1 kHz audio
+            audio7(7),                  -- 7 kHz audio
+            video(8),
+            packetSwitched(9),
+            fax(10)
+        }
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The information type for this call."
+        ::= { callHistoryEntry 12 }
+
+callHistoryTransmitPackets OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS     current
+        DESCRIPTION
+            "The number of packets which were transmitted while this
+             call was active."
+        ::= { callHistoryEntry 13 }
+
+callHistoryTransmitBytes OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of bytes which were transmitted while this
+             call was active."
+        ::= { callHistoryEntry 14 }
+
+callHistoryReceivePackets OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of packets which were received while this
+             call was active."
+        ::= { callHistoryEntry 15 }
+
+callHistoryReceiveBytes OBJECT-TYPE
+        SYNTAX      AbsoluteCounter32
+        MAX-ACCESS  read-only
+        STATUS      current
+        DESCRIPTION
+            "The number of bytes which were received while this
+             call was active."
+        ::= { callHistoryEntry 16 }
+
+-- Traps related to Connection management
+
+dialControlMibTrapPrefix OBJECT IDENTIFIER ::= { dialControlMib 2 }
+dialControlMibTraps OBJECT IDENTIFIER ::= { dialControlMibTrapPrefix 0 }
+
+dialCtlPeerCallInformation NOTIFICATION-TYPE
+        OBJECTS {
+            callHistoryPeerId,
+            callHistoryPeerIfIndex,
+            callHistoryLogicalIfIndex,
+            ifOperStatus,
+            callHistoryPeerAddress,
+            callHistoryPeerSubAddress,
+            callHistoryDisconnectCause,
+            callHistoryConnectTime,
+            callHistoryDisconnectTime,
+            callHistoryInfoType,
+            callHistoryCallOrigin
+        }
+        STATUS      current
+        DESCRIPTION
+            "This trap/inform is sent to the manager whenever
+             a successful call clears, or a failed call attempt
+             is determined to have ultimately failed. In the
+             event that call retry is active, then this is after
+             all retry attempts have failed. However, only one such
+             trap is sent in between successful call attempts;
+             subsequent call attempts result in no trap.
+             ifOperStatus will return the operational status of the
+             virtual interface associated with the peer to whom
+             this call was made to."
+     ::= { dialControlMibTraps 1 }
+
+dialCtlPeerCallSetup NOTIFICATION-TYPE
+        OBJECTS {
+            callActivePeerId,
+            callActivePeerIfIndex,
+            callActiveLogicalIfIndex,
+            ifOperStatus,
+            callActivePeerAddress,
+            callActivePeerSubAddress,
+            callActiveInfoType,
+            callActiveCallOrigin
+        }
+        STATUS      current
+        DESCRIPTION
+            "This trap/inform is sent to the manager whenever
+             a call setup message is received or sent.
+             ifOperStatus will return the operational status of the
+             virtual interface associated with the peer to whom
+             this call was made to."
+     ::= { dialControlMibTraps 2 }
+
+-- conformance information
+
+dialControlMibConformance OBJECT IDENTIFIER ::=
+                                { dialControlMib 3 }
+dialControlMibCompliances OBJECT IDENTIFIER ::=
+                                { dialControlMibConformance 1 }
+dialControlMibGroups      OBJECT IDENTIFIER ::=
+                                { dialControlMibConformance 2 }
+
+-- compliance statements
+
+dialControlMibCompliance MODULE-COMPLIANCE
+        STATUS      current
+        DESCRIPTION
+            "The compliance statement for entities which
+             implement the DIAL CONTROL MIB"
+        MODULE      -- this module
+        MANDATORY-GROUPS
+            { dialControlGroup, callActiveGroup, callHistoryGroup
+--              ,callNotificationsGroup
+	    }
+        ::= { dialControlMibCompliances 1 }
+
+-- units of conformance
+
+dialControlGroup OBJECT-GROUP
+        OBJECTS {
+            dialCtlAcceptMode,
+            dialCtlTrapEnable,
+            dialCtlPeerCfgIfType,
+            dialCtlPeerCfgLowerIf,
+            dialCtlPeerCfgOriginateAddress,
+            dialCtlPeerCfgAnswerAddress,
+            dialCtlPeerCfgSubAddress,
+            dialCtlPeerCfgClosedUserGroup,
+            dialCtlPeerCfgSpeed,
+            dialCtlPeerCfgInfoType,
+            dialCtlPeerCfgPermission,
+            dialCtlPeerCfgInactivityTimer,
+            dialCtlPeerCfgMinDuration,
+            dialCtlPeerCfgMaxDuration,
+            dialCtlPeerCfgCarrierDelay,
+            dialCtlPeerCfgCallRetries,
+            dialCtlPeerCfgRetryDelay,
+            dialCtlPeerCfgFailureDelay,
+            dialCtlPeerCfgTrapEnable,
+            dialCtlPeerCfgStatus,
+            dialCtlPeerStatsConnectTime,
+            dialCtlPeerStatsChargedUnits,
+            dialCtlPeerStatsSuccessCalls,
+            dialCtlPeerStatsFailCalls,
+            dialCtlPeerStatsAcceptCalls,
+            dialCtlPeerStatsRefuseCalls,
+            dialCtlPeerStatsLastDisconnectCause,
+            dialCtlPeerStatsLastDisconnectText,
+            dialCtlPeerStatsLastSetupTime
+        }
+        STATUS      current
+        DESCRIPTION
+            "A collection of objects providing the DIAL CONTROL
+             capability."
+        ::= { dialControlMibGroups 1 }
+
+callActiveGroup OBJECT-GROUP
+        OBJECTS {
+            callActivePeerAddress,
+            callActivePeerSubAddress,
+            callActivePeerId,
+            callActivePeerIfIndex,
+            callActiveLogicalIfIndex,
+            callActiveConnectTime,
+            callActiveCallState,
+            callActiveCallOrigin,
+            callActiveChargedUnits,
+            callActiveInfoType,
+            callActiveTransmitPackets,
+            callActiveTransmitBytes,
+            callActiveReceivePackets,
+            callActiveReceiveBytes
+        }
+        STATUS      current
+        DESCRIPTION
+            "A collection of objects providing the active call
+             capability."
+        ::= { dialControlMibGroups 2 }
+
+callHistoryGroup OBJECT-GROUP
+        OBJECTS {
+            callHistoryTableMaxLength,
+            callHistoryRetainTimer,
+            callHistoryPeerAddress,
+            callHistoryPeerSubAddress,
+            callHistoryPeerId,
+            callHistoryPeerIfIndex,
+            callHistoryLogicalIfIndex,
+            callHistoryDisconnectCause,
+            callHistoryDisconnectText,
+            callHistoryConnectTime,
+            callHistoryDisconnectTime,
+            callHistoryCallOrigin,
+            callHistoryChargedUnits,
+            callHistoryInfoType,
+            callHistoryTransmitPackets,
+            callHistoryTransmitBytes,
+            callHistoryReceivePackets,
+            callHistoryReceiveBytes
+        }
+        STATUS      current
+        DESCRIPTION
+            "A collection of objects providing the Call History
+             capability."
+        ::= { dialControlMibGroups 3 }
+
+--callNotificationsGroup NOTIFICATION-GROUP
+--    NOTIFICATIONS { dialCtlPeerCallInformation, dialCtlPeerCallSetup }
+--    STATUS        current
+--    DESCRIPTION
+--            "The notifications which a Dial Control MIB entity is
+--             required to implement."
+--    ::= { dialControlMibGroups 4 }
+
+
+END