Initial commitHEADmain

1 files changed, 1913 insertions, 0 deletions

diff --git a/MIBS/UPS-MIB b/MIBS/UPS-MIB
new file mode 100644
index 0000000..fca2b5b
--- /dev/null
+++ b/MIBS/UPS-MIB
@@ -0,0 +1,1913 @@
+UPS-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
+    OBJECT-IDENTITY, Counter32, Gauge32, Integer32, mib-2
+        FROM SNMPv2-SMI
+    DisplayString, TimeStamp, TimeInterval, TestAndIncr,
+      AutonomousType, TEXTUAL-CONVENTION
+        FROM SNMPv2-TC
+    MODULE-COMPLIANCE, OBJECT-GROUP
+        FROM SNMPv2-CONF;
+
+
+upsMIB MODULE-IDENTITY
+    LAST-UPDATED "9402230000Z"
+    ORGANIZATION "IETF UPS MIB Working Group"
+    CONTACT-INFO
+           "        Jeffrey D. Case
+
+             Postal: SNMP Research, Incorporated
+                     3001 Kimberlin Heights Road
+                     Knoxville, TN  37920
+                     US
+
+                Tel: +1 615 573 1434
+                Fax: +1 615 573 9197
+
+             E-mail: case@snmp.com"
+    DESCRIPTION
+            "The MIB module to describe Uninterruptible Power
+            Supplies."
+    ::= { mib-2 33 }
+
+PositiveInteger ::= TEXTUAL-CONVENTION
+    DISPLAY-HINT "d"
+    STATUS       current
+    DESCRIPTION
+            "This data type is a non-zero and non-negative value."
+    SYNTAX       INTEGER (1..2147483647)
+
+NonNegativeInteger ::= TEXTUAL-CONVENTION
+    DISPLAY-HINT "d"
+    STATUS       current
+    DESCRIPTION
+            "This data type is a non-negative value."
+    SYNTAX       INTEGER (0..2147483647)
+upsObjects            OBJECT IDENTIFIER ::= { upsMIB 1 }
+
+
+--
+-- The Device Identification group.
+--      All objects in this group except for upsIdentName and
+--      upsIdentAttachedDevices are set at device initialization
+--      and remain static.
+--
+
+upsIdent              OBJECT IDENTIFIER ::= { upsObjects 1 }
+
+upsIdentManufacturer OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..31))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The name of the UPS manufacturer."
+    ::= { upsIdent 1 }
+
+upsIdentModel OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..63))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The UPS Model designation."
+    ::= { upsIdent 2 }
+
+upsIdentUPSSoftwareVersion OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..63))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The UPS firmware/software version(s).  This variable
+            may or may not have the same value as
+            upsIdentAgentSoftwareVersion in some implementations."
+    ::= { upsIdent 3 }
+
+upsIdentAgentSoftwareVersion OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..63))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The UPS agent software version.  This variable may or
+            may not have the same value as
+            upsIdentUPSSoftwareVersion in some implementations."
+    ::= { upsIdent 4 }
+
+upsIdentName OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE(0..63))
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "A string identifying the UPS.  This object should be
+            set by the administrator."
+    ::= { upsIdent 5 }
+
+upsIdentAttachedDevices OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE(0..63))
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "A string identifying the devices attached to the
+            output(s) of the UPS.  This object should be set by
+            the administrator."
+    ::= { upsIdent 6 }
+
+
+--
+-- Battery Group
+--
+
+upsBattery            OBJECT IDENTIFIER ::= { upsObjects 2 }
+
+upsBatteryStatus OBJECT-TYPE
+    SYNTAX     INTEGER {
+        unknown(1),
+        batteryNormal(2),
+        batteryLow(3),
+        batteryDepleted(4)
+    }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The indication of the capacity remaining in the UPS
+            system's batteries.   A value of batteryNormal
+            indicates that the remaining run-time is greater than
+            upsConfigLowBattTime.  A value of batteryLow indicates
+            that the remaining battery run-time is less than or
+            equal to upsConfigLowBattTime.  A value of
+            batteryDepleted indicates that the UPS will be unable
+            to sustain the present load when and if the utility
+            power is lost (including the possibility that the
+            utility power is currently absent and the UPS is
+            unable to sustain the output)."
+    ::= { upsBattery 1 }
+
+upsSecondsOnBattery OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "seconds"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "If the unit is on battery power, the elapsed time
+            since the UPS last switched to battery power, or the
+            time since the network management subsystem was last
+            restarted, whichever is less.  Zero shall be returned
+            if the unit is not on battery power."
+    ::= { upsBattery 2 }
+
+upsEstimatedMinutesRemaining OBJECT-TYPE
+    SYNTAX     PositiveInteger
+    UNITS      "minutes"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "An estimate of the time to battery charge depletion
+            under the present load conditions if the utility power
+            is off and remains off, or if it were to be lost and
+            remain off."
+    ::= { upsBattery 3 }
+
+upsEstimatedChargeRemaining OBJECT-TYPE
+    SYNTAX     INTEGER (0..100)
+    UNITS      "percent"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "An estimate of the battery charge remaining expressed
+            as a percent of full charge."
+    ::= { upsBattery 4 }
+
+upsBatteryVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Volt DC"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the present battery voltage."
+    ::= { upsBattery 5 }
+
+upsBatteryCurrent OBJECT-TYPE
+    SYNTAX     Integer32
+    UNITS      "0.1 Amp DC"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present battery current."
+    ::= { upsBattery 6 }
+
+upsBatteryTemperature OBJECT-TYPE
+    SYNTAX     Integer32
+    UNITS      "degrees Centigrade"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The ambient temperature at or near the UPS Battery
+            casing."
+    ::= { upsBattery 7 }
+
+
+--
+-- Input Group
+--
+
+upsInput              OBJECT IDENTIFIER ::= { upsObjects 3 }
+
+upsInputLineBads OBJECT-TYPE
+    SYNTAX     Counter32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "A count of the number of times the input entered an
+            out-of-tolerance condition as defined by the
+            manufacturer.  This count is incremented by one each
+            time the input transitions from zero out-of-tolerance
+            lines to one or more input lines out-of-tolerance."
+    ::= { upsInput 1 }
+
+
+upsInputNumLines OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of input lines utilized in this device.
+            This variable indicates the number of rows in the
+            input table."
+    ::= { upsInput 2 }
+
+upsInputTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF UpsInputEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A list of input table entries.  The number of entries
+            is given by the value of upsInputNumLines."
+    ::= { upsInput 3 }
+
+upsInputEntry OBJECT-TYPE
+    SYNTAX     UpsInputEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry containing information applicable to a
+            particular input line."
+    INDEX { upsInputLineIndex }
+    ::= { upsInputTable 1 }
+
+UpsInputEntry ::= SEQUENCE {
+    upsInputLineIndex   PositiveInteger,
+    upsInputFrequency   NonNegativeInteger,
+    upsInputVoltage     NonNegativeInteger,
+    upsInputCurrent     NonNegativeInteger,
+    upsInputTruePower   NonNegativeInteger
+}
+
+upsInputLineIndex OBJECT-TYPE
+    SYNTAX     PositiveInteger
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The input line identifier."
+    ::= { upsInputEntry 1 }
+
+upsInputFrequency OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Hertz"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present input frequency."
+    ::= { upsInputEntry 2 }
+
+upsInputVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the present input voltage."
+    ::= { upsInputEntry 3 }
+
+upsInputCurrent OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 RMS Amp"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the present input current."
+    ::= { upsInputEntry 4 }
+
+upsInputTruePower OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "Watts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the present input true power."
+    ::= { upsInputEntry 5 }
+
+
+--
+-- The Output group.
+--
+
+upsOutput             OBJECT IDENTIFIER ::= { upsObjects 4 }
+
+upsOutputSource OBJECT-TYPE
+    SYNTAX     INTEGER {
+        other(1),
+        none(2),
+        normal(3),
+        bypass(4),
+        battery(5),
+        booster(6),
+        reducer(7)
+    }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present source of output power.  The enumeration
+            none(2) indicates that there is no source of output
+            power (and therefore no output power), for example,
+            the system has opened the output breaker."
+    ::= { upsOutput 1 }
+
+upsOutputFrequency OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Hertz"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present output frequency."
+    ::= { upsOutput 2 }
+
+upsOutputNumLines OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of output lines utilized in this device.
+            This variable indicates the number of rows in the
+            output table."
+    ::= { upsOutput 3 }
+
+upsOutputTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF UpsOutputEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A list of output table entries.  The number of
+            entries is given by the value of upsOutputNumLines."
+    ::= { upsOutput 4 }
+
+upsOutputEntry OBJECT-TYPE
+    SYNTAX     UpsOutputEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry containing information applicable to a
+            particular output line."
+    INDEX { upsOutputLineIndex }
+    ::= { upsOutputTable 1 }
+
+UpsOutputEntry ::= SEQUENCE {
+    upsOutputLineIndex   PositiveInteger,
+    upsOutputVoltage     NonNegativeInteger,
+    upsOutputCurrent     NonNegativeInteger,
+    upsOutputPower       NonNegativeInteger,
+    upsOutputPercentLoad INTEGER
+}
+
+upsOutputLineIndex OBJECT-TYPE
+    SYNTAX     PositiveInteger
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The output line identifier."
+    ::= { upsOutputEntry 1 }
+
+upsOutputVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present output voltage."
+    ::= { upsOutputEntry 2 }
+
+upsOutputCurrent OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 RMS Amp"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present output current."
+    ::= { upsOutputEntry 3 }
+
+upsOutputPower OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "Watts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present output true power."
+    ::= { upsOutputEntry 4 }
+
+upsOutputPercentLoad OBJECT-TYPE
+    SYNTAX     INTEGER (0..200)
+    UNITS      "percent"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The percentage of the UPS power capacity presently
+            being used on this output line, i.e., the greater of
+            the percent load of true power capacity and the
+            percent load of VA."
+    ::= { upsOutputEntry 5 }
+
+--
+-- The Bypass group.
+--
+
+upsBypass             OBJECT IDENTIFIER ::= { upsObjects 5 }
+
+upsBypassFrequency OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Hertz"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present bypass frequency."
+    ::= { upsBypass 1 }
+
+upsBypassNumLines OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The number of bypass lines utilized in this device.
+            This entry indicates the number of rows in the bypass
+            table."
+    ::= { upsBypass 2 }
+
+upsBypassTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF UpsBypassEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A list of bypass table entries.  The number of
+            entries is given by the value of upsBypassNumLines."
+    ::= { upsBypass 3 }
+
+upsBypassEntry OBJECT-TYPE
+    SYNTAX     UpsBypassEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry containing information applicable to a
+            particular bypass input."
+    INDEX { upsBypassLineIndex }
+    ::= { upsBypassTable 1 }
+
+UpsBypassEntry ::= SEQUENCE {
+    upsBypassLineIndex  PositiveInteger,
+    upsBypassVoltage    NonNegativeInteger,
+    upsBypassCurrent    NonNegativeInteger,
+    upsBypassPower      NonNegativeInteger
+}
+
+upsBypassLineIndex OBJECT-TYPE
+    SYNTAX     PositiveInteger
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "The bypass line identifier."
+    ::= { upsBypassEntry 1 }
+
+upsBypassVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present bypass voltage."
+    ::= { upsBypassEntry 2 }
+
+upsBypassCurrent OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 RMS Amp"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present bypass current."
+    ::= { upsBypassEntry 3 }
+
+upsBypassPower OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "Watts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present true power conveyed by the bypass."
+    ::= { upsBypassEntry 4 }
+
+
+--
+-- The Alarm group.
+--
+
+upsAlarm              OBJECT IDENTIFIER ::= { upsObjects 6 }
+
+upsAlarmsPresent OBJECT-TYPE
+    SYNTAX     Gauge32
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The present number of active alarm conditions."
+    ::= { upsAlarm 1 }
+
+upsAlarmTable OBJECT-TYPE
+    SYNTAX     SEQUENCE OF UpsAlarmEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A list of alarm table entries.  The table contains
+            zero, one, or many rows at any moment, depending upon
+            the number of alarm conditions in effect.  The table
+            is initially empty at agent startup.  The agent
+            creates a row in the table each time a condition is
+            detected and deletes that row when that condition no
+            longer pertains.  The agent creates the first row with
+            upsAlarmId equal to 1, and increments the value of
+            upsAlarmId each time a new row is created, wrapping to
+            the first free value greater than or equal to 1 when
+            the maximum value of upsAlarmId would otherwise be
+            exceeded.  Consequently, after multiple operations,
+            the table may become sparse, e.g., containing entries
+            for rows 95, 100, 101, and 203 and the entries should
+            not be assumed to be in chronological order because
+            upsAlarmId might have wrapped.
+
+            Alarms are named by an AutonomousType (OBJECT
+            IDENTIFIER), upsAlarmDescr, to allow a single table to
+            reflect well known alarms plus alarms defined by a
+            particular implementation, i.e., as documented in the
+            private enterprise MIB definition for the device.  No
+            two rows will have the same value of upsAlarmDescr,
+            since alarms define conditions.  In order to meet this
+            requirement, care should be taken in the definition of
+            alarm conditions to insure that a system cannot enter
+            the same condition multiple times simultaneously.
+
+            The number of rows in the table at any given time is
+            reflected by the value of upsAlarmsPresent."
+    ::= { upsAlarm 2 }
+
+upsAlarmEntry OBJECT-TYPE
+    SYNTAX     UpsAlarmEntry
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "An entry containing information applicable to a
+            particular alarm."
+    INDEX { upsAlarmId }
+    ::= { upsAlarmTable 1 }
+
+UpsAlarmEntry ::= SEQUENCE {
+    upsAlarmId          PositiveInteger,
+    upsAlarmDescr       AutonomousType,
+    upsAlarmTime        TimeStamp
+}
+
+upsAlarmId OBJECT-TYPE
+    SYNTAX     PositiveInteger
+    MAX-ACCESS not-accessible
+    STATUS     current
+    DESCRIPTION
+            "A unique identifier for an alarm condition.  This
+            value must remain constant."
+    ::= { upsAlarmEntry 1 }
+
+upsAlarmDescr OBJECT-TYPE
+    SYNTAX     AutonomousType
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "A reference to an alarm description object.  The
+            object referenced should not be accessible, but rather
+            be used to provide a unique description of the alarm
+            condition."
+    ::= { upsAlarmEntry 2 }
+
+upsAlarmTime OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The value of sysUpTime when the alarm condition was
+            detected.  If the alarm condition was detected at the
+            time of agent startup and presumably existed before
+            agent startup, the value of upsAlarmTime shall equal
+            0."
+    ::= { upsAlarmEntry 3 }
+
+
+--
+-- Well known alarm conditions.
+--
+
+upsWellKnownAlarms    OBJECT IDENTIFIER ::= { upsAlarm 3 }
+
+upsAlarmBatteryBad OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "One or more batteries have been determined to require
+            replacement."
+    ::= { upsWellKnownAlarms  1 }
+
+upsAlarmOnBattery OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS is drawing power from the batteries."
+    ::= { upsWellKnownAlarms  2 }
+
+upsAlarmLowBattery OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The remaining battery run-time is less than or equal
+            to upsConfigLowBattTime."
+    ::= { upsWellKnownAlarms  3 }
+
+
+upsAlarmDepletedBattery OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS will be unable to sustain the present load
+            when and if the utility power is lost."
+    ::= { upsWellKnownAlarms  4 }
+
+upsAlarmTempBad OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A temperature is out of tolerance."
+    ::= { upsWellKnownAlarms  5 }
+
+upsAlarmInputBad OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "An input condition is out of tolerance."
+    ::= { upsWellKnownAlarms  6 }
+
+upsAlarmOutputBad OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "An output condition (other than OutputOverload) is
+            out of tolerance."
+    ::= { upsWellKnownAlarms  7 }
+
+upsAlarmOutputOverload OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The output load exceeds the UPS output capacity."
+    ::= { upsWellKnownAlarms  8 }
+
+upsAlarmOnBypass OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The Bypass is presently engaged on the UPS."
+    ::= { upsWellKnownAlarms  9 }
+
+upsAlarmBypassBad OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The Bypass is out of tolerance."
+    ::= { upsWellKnownAlarms 10 }
+
+upsAlarmOutputOffAsRequested OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS has shutdown as requested, i.e., the output
+            is off."
+    ::= { upsWellKnownAlarms 11 }
+
+upsAlarmUpsOffAsRequested OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The entire UPS has shutdown as commanded."
+    ::= { upsWellKnownAlarms 12 }
+
+upsAlarmChargerFailed OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "An uncorrected problem has been detected within the
+            UPS charger subsystem."
+    ::= { upsWellKnownAlarms 13 }
+
+upsAlarmUpsOutputOff OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The output of the UPS is in the off state."
+    ::= { upsWellKnownAlarms 14 }
+
+upsAlarmUpsSystemOff OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS system is in the off state."
+    ::= { upsWellKnownAlarms 15 }
+
+upsAlarmFanFailure OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The failure of one or more fans in the UPS has been
+            detected."
+    ::= { upsWellKnownAlarms 16 }
+
+upsAlarmFuseFailure OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The failure of one or more fuses has been detected."
+    ::= { upsWellKnownAlarms 17 }
+
+upsAlarmGeneralFault OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A general fault in the UPS has been detected."
+    ::= { upsWellKnownAlarms 18 }
+
+upsAlarmDiagnosticTestFailed OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The result of the last diagnostic test indicates a
+            failure."
+    ::= { upsWellKnownAlarms 19 }
+
+upsAlarmCommunicationsLost OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A problem has been encountered in the communications
+            between the agent and the UPS."
+    ::= { upsWellKnownAlarms 20 }
+
+upsAlarmAwaitingPower OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS output is off and the UPS is awaiting the
+            return of input power."
+    ::= { upsWellKnownAlarms 21 }
+
+upsAlarmShutdownPending OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A upsShutdownAfterDelay countdown is underway."
+    ::= { upsWellKnownAlarms 22 }
+
+upsAlarmShutdownImminent OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The UPS will turn off power to the load in less than
+            5 seconds; this may be either a timed shutdown or a
+            low battery shutdown."
+    ::= { upsWellKnownAlarms 23 }
+
+upsAlarmTestInProgress OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A test is in progress, as initiated and indicated by
+            the Test Group.  Tests initiated via other
+            implementation-specific mechanisms can indicate the
+            presence of the testing in the alarm table, if
+            desired, via a OBJECT-IDENTITY macro in the MIB
+            document specific to that implementation and are
+            outside the scope of this OBJECT-IDENTITY."
+    ::= { upsWellKnownAlarms 24 }
+
+
+--
+-- The Test Group
+--
+
+upsTest               OBJECT IDENTIFIER ::= { upsObjects 7 }
+
+upsTestId OBJECT-TYPE
+    SYNTAX     OBJECT IDENTIFIER
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The test is named by an OBJECT IDENTIFIER which
+            allows a standard mechanism for the initiation of
+            tests, including the well known tests identified in
+            this document as well as those introduced by a
+            particular implementation, i.e., as documented in the
+            private enterprise MIB definition for the device.
+
+            Setting this variable initiates the named test. Sets
+            to this variable require the presence of
+            upsTestSpinLock in the same SNMP message.
+
+            The set request will be rejected with an appropriate
+            error message if the requested test cannot be
+            performed, including attempts to start a test when
+            another test is already in progress.  The status of
+            the current or last test is maintained in
+            upsTestResultsSummary. Tests in progress may be
+            aborted by setting the upsTestId variable to
+            upsTestAbortTestInProgress.
+
+            Read operations return the value of the name of the
+            test in progress if a test is in progress or the name
+            of the last test performed if no test is in progress,
+            unless no test has been run, in which case the well
+            known value upsTestNoTestsInitiated is returned."
+    ::= { upsTest 1 }
+
+-- see [6] for more information on the semantics of objects with
+-- syntax of TestAndIncr
+
+upsTestSpinLock OBJECT-TYPE
+    SYNTAX     TestAndIncr
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "A spin lock on the test subsystem.  The spinlock is
+            used as follows.
+
+            Before starting a test, a manager-station should make
+            sure that a test is not in progress as follows:
+
+                try_again:
+                  get (upsTestSpinLock)
+                  while (upsTestResultsSummary == inProgress) {
+                    /* loop while a test is running for another
+            manager */
+                    short delay
+                    get (upsTestSpinLock)
+                  }
+                  lock_value = upsTestSpinLock
+                  /* no test in progress, start the test */
+                  set (upsTestSpinLock = lock_value, upsTestId =
+            requested_test)
+                  if (error_index == 1) { /* (upsTestSpinLock
+            failed) */
+                    /* if problem is not access control, then
+                        some other manager slipped in ahead of us
+            */
+                    goto try_again
+                  }
+                  if (error_index == 2) { /* (upsTestId) */
+                    /* cannot perform the test */
+                    give up
+                  }
+                  /* test started ok */
+                  /* wait for test completion by polling
+            upsTestResultsSummary */
+                  get (upsTestSpinLock, upsTestResultsSummary,
+            upsTestResultsDetail)
+                  while (upsTestResultsSummary == inProgress) {
+                    short delay
+                    get (upsTestSpinLock, upsTestResultsSummary,
+            upsTestResultsDetail)
+                  }
+                  /* when test completes, retrieve any additional
+            test results */
+                  /* if upsTestSpinLock == lock_value + 1, then
+            these are our test */
+                  /* results (as opposed to another manager's */
+                  The initial value of upsTestSpinLock at agent
+            initialization shall
+                  be 1."
+    ::= { upsTest 2 }
+
+upsTestResultsSummary OBJECT-TYPE
+    SYNTAX     INTEGER {
+        donePass(1),
+        doneWarning(2),
+        doneError(3),
+        aborted(4),
+        inProgress(5),
+        noTestsInitiated(6)
+    }
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The results of the current or last UPS diagnostics
+            test performed.  The values for donePass(1),
+            doneWarning(2), and doneError(3) indicate that the
+            test completed either successfully, with a warning, or
+            with an error, respectively.  The value aborted(4) is
+            returned for tests which are aborted by setting the
+            value of upsTestId to upsTestAbortTestInProgress.
+            Tests which have not yet concluded are indicated by
+            inProgress(5).  The value noTestsInitiated(6)
+            indicates that no previous test results are available,
+            such as is the case when no tests have been run since
+            the last reinitialization of the network management
+            subsystem and the system has no provision for non-
+            volatile storage of test results."
+    ::= { upsTest 3 }
+
+upsTestResultsDetail OBJECT-TYPE
+    SYNTAX     DisplayString (SIZE (0..255))
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "Additional information about upsTestResultsSummary.
+            If no additional information available, a zero length
+            string is returned."
+    ::= { upsTest 4 }
+
+upsTestStartTime OBJECT-TYPE
+    SYNTAX     TimeStamp
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The value of sysUpTime at the time the test in
+            progress was initiated, or, if no test is in progress,
+            the time the previous test was initiated.  If the
+            value of upsTestResultsSummary is noTestsInitiated(6),
+            upsTestStartTime has the value 0."
+    ::= { upsTest 5 }
+
+upsTestElapsedTime OBJECT-TYPE
+    SYNTAX     TimeInterval
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The amount of time, in TimeTicks, since the test in
+            progress was initiated, or, if no test is in progress,
+            the previous test took to complete.  If the value of
+            upsTestResultsSummary is noTestsInitiated(6),
+            upsTestElapsedTime has the value 0."
+    ::= { upsTest 6 }
+
+--
+-- Well known tests.
+--
+
+upsWellKnownTests     OBJECT IDENTIFIER ::= { upsTest 7 }
+
+
+upsTestNoTestsInitiated OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "No tests have been initiated and no test is in
+            progress."
+    ::= { upsWellKnownTests  1 }
+
+upsTestAbortTestInProgress OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The test in progress is to be aborted / the test in
+            progress was aborted."
+    ::= { upsWellKnownTests  2 }
+
+upsTestGeneralSystemsTest OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The manufacturer's standard test of UPS device
+            systems."
+    ::= { upsWellKnownTests  3 }
+
+upsTestQuickBatteryTest OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "A test that is sufficient to determine if the battery
+            needs replacement."
+    ::= { upsWellKnownTests  4 }
+
+upsTestDeepBatteryCalibration OBJECT-IDENTITY
+    STATUS     current
+    DESCRIPTION
+            "The system is placed on battery to a discharge level,
+            set by the manufacturer, sufficient to determine
+            battery replacement and battery run-time with a high
+            degree of confidence.  WARNING:  this test will leave
+            the battery in a low charge state and will require
+            time for recharging to a level sufficient to provide
+            normal battery duration for the protected load."
+    ::= { upsWellKnownTests  5 }
+
+
+--
+-- The Control group.
+--
+
+upsControl            OBJECT IDENTIFIER ::= { upsObjects 8 }
+
+upsShutdownType OBJECT-TYPE
+    SYNTAX     INTEGER {
+        output(1),
+        system(2)
+    }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "This object determines the nature of the action to be
+            taken at the time when the countdown of the
+            upsShutdownAfterDelay and upsRebootWithDuration
+            objects reaches zero.
+
+            Setting this object to output(1) indicates that
+            shutdown requests should cause only the output of the
+            UPS to turn off.  Setting this object to system(2)
+            indicates that shutdown requests will cause the entire
+            UPS system to turn off."
+    ::= { upsControl 1 }
+
+upsShutdownAfterDelay OBJECT-TYPE
+    SYNTAX     INTEGER (-1..2147483648)
+    UNITS      "seconds"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Setting this object will shutdown (i.e., turn off)
+            either the UPS output or the UPS system (as determined
+            by the value of upsShutdownType at the time of
+            shutdown) after the indicated number of seconds, or
+            less if the UPS batteries become depleted. Setting
+            this object to 0 will cause the shutdown to occur
+            immediately.  Setting this object to -1 will abort the
+            countdown.  If the system is already in the desired
+            state at the time the countdown reaches 0, then
+            nothing will happen.  That is, there is no additional
+            action at that time if upsShutdownType = system and
+            the system is already off.  Similarly, there is no
+            additional action at that time if upsShutdownType =
+            output and the output is already off.  When read,
+            upsShutdownAfterDelay will return the number of
+            seconds remaining until shutdown, or -1 if no shutdown
+            countdown is in effect.  On some systems, if the agent
+            is restarted while a shutdown countdown is in effect,
+            the countdown may be aborted.  Sets to this object
+            override any upsShutdownAfterDelay already in effect."
+    ::= { upsControl 2 }
+
+upsStartupAfterDelay OBJECT-TYPE
+    SYNTAX     INTEGER (-1..2147483648)
+    UNITS      "seconds"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Setting this object will start the output after the
+            indicated number of seconds, including starting the
+            UPS, if necessary.  Setting this object to 0 will
+            cause the startup to occur immediately.  Setting this
+            object to -1 will abort the countdown.  If the output
+            is already on at the time the countdown reaches 0,
+            then nothing will happen.  Sets to this object
+            override the effect of any upsStartupAfterDelay
+            countdown or upsRebootWithDuration countdown in
+            progress.  When read, upsStartupAfterDelay will return
+            the number of seconds until startup, or -1 if no
+            startup countdown is in effect.  If the countdown
+            expires during a utility failure, the startup shall
+            not occur until the utility power is restored.  On
+            some systems, if the agent is restarted while a
+            startup countdown is in effect, the countdown is
+            aborted."
+    ::= { upsControl 3 }
+
+upsRebootWithDuration OBJECT-TYPE
+    SYNTAX     INTEGER (-1..300)
+    UNITS      "seconds"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Setting this object will immediately shutdown (i.e.,
+            turn off) either the UPS output or the UPS system (as
+            determined by the value of upsShutdownType at the time
+            of shutdown) for a period equal to the indicated
+            number of seconds, after which time the output will be
+            started, including starting the UPS, if necessary.  If
+            the number of seconds required to perform the request
+            is greater than the requested duration, then the
+            requested shutdown and startup cycle shall be
+            performed in the minimum time possible, but in no case
+            shall this require more than the requested duration
+            plus 60 seconds.  When read, upsRebootWithDuration
+            shall return the number of seconds remaining in the
+            countdown, or -1 if no countdown is in progress.  If
+            the startup should occur during a utility failure, the
+            startup shall not occur until the utility power is
+            restored."
+    ::= { upsControl 4 }
+
+upsAutoRestart OBJECT-TYPE
+    SYNTAX     INTEGER {
+        on(1),
+        off(2)
+    }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "Setting this object to 'on' will cause the UPS system
+            to restart after a shutdown if the shutdown occurred
+            during a power loss as a result of either a
+            upsShutdownAfterDelay or an internal battery depleted
+            condition.  Setting this object to 'off' will prevent
+            the UPS system from restarting after a shutdown until
+            an operator manually or remotely explicitly restarts
+            it.  If the UPS is in a startup or reboot countdown,
+            then the UPS will not restart until that delay has
+            been satisfied."
+    ::= { upsControl 5 }
+
+
+--
+-- The Configuration group.
+--
+
+upsConfig             OBJECT IDENTIFIER ::= { upsObjects 9 }
+
+upsConfigInputVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the nominal input voltage.  On those
+            systems which support read-write access to this
+            object, if there is an attempt to set this variable to
+            a value that is not supported, the request must be
+            rejected and the agent shall respond with an
+            appropriate error message, i.e., badValue for SNMPv1,
+            or inconsistentValue for SNMPv2."
+    ::= { upsConfig 1 }
+
+upsConfigInputFreq OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Hertz"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The nominal input frequency.  On those systems which
+            support read-write access to this object, if there is
+            an attempt to set this variable to a value that is not
+            supported, the request must be rejected and the agent
+            shall respond with an appropriate error message, i.e.,
+            badValue for SNMPv1, or inconsistentValue for SNMPv2."
+    ::= { upsConfig 2 }
+
+upsConfigOutputVoltage OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the nominal output voltage.  On
+            those systems which support read-write access to this
+            object, if there is an attempt to set this variable to
+            a value that is not supported, the request must be
+            rejected and the agent shall respond with an
+            appropriate error message, i.e., badValue for SNMPv1,
+            or inconsistentValue for SNMPv2."
+    ::= { upsConfig 3 }
+
+upsConfigOutputFreq OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "0.1 Hertz"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The nominal output frequency.  On those systems which
+            support read-write access to this object, if there is
+            an attempt to set this variable to a value that is not
+            supported, the request must be rejected and the agent
+            shall respond with an appropriate error message, i.e.,
+            badValue for SNMPv1, or inconsistentValue for SNMPv2."
+    ::= { upsConfig 4 }
+
+upsConfigOutputVA OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "Volt-Amps"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the nominal Volt-Amp rating."
+    ::= { upsConfig 5 }
+
+upsConfigOutputPower OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "Watts"
+    MAX-ACCESS read-only
+    STATUS     current
+    DESCRIPTION
+            "The magnitude of the nominal true power rating."
+    ::= { upsConfig 6 }
+
+upsConfigLowBattTime OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "minutes"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The value of upsEstimatedMinutesRemaining at which a
+            lowBattery condition is declared.  For agents which
+            support only discrete (discontinuous) values, then the
+            agent shall round up to the next supported value.  If
+            the requested value is larger than the largest
+            supported value, then the largest supported value
+            shall be selected."
+    ::= { upsConfig 7 }
+
+upsConfigAudibleStatus OBJECT-TYPE
+    SYNTAX     INTEGER {
+        disabled(1),
+        enabled(2),
+        muted(3)
+    }
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The requested state of the audible alarm.  When in
+            the disabled state, the audible alarm should never
+            sound.  The enabled state is self-describing.  Setting
+            this object to muted(3) when the audible alarm is
+            sounding shall temporarily silence the alarm.  It will
+            remain muted until it would normally stop sounding and
+            the value returned for read operations during this
+            period shall equal muted(3).  At the end of this
+            period, the value shall revert to enabled(2).  Writes
+            of the value muted(3) when the audible alarm is not
+            sounding shall be accepted but otherwise shall have no
+            effect."
+    ::= { upsConfig 8 }
+
+upsConfigLowVoltageTransferPoint OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The minimum input line voltage allowed before the UPS
+            system transfers to battery backup."
+    ::= { upsConfig 9 }
+
+upsConfigHighVoltageTransferPoint OBJECT-TYPE
+    SYNTAX     NonNegativeInteger
+    UNITS      "RMS Volts"
+    MAX-ACCESS read-write
+    STATUS     current
+    DESCRIPTION
+            "The maximum line voltage allowed before the UPS
+            system transfers to battery backup."
+    ::= { upsConfig 10 }
+
+
+--
+-- notifications, i.e., traps
+--
+upsTraps              OBJECT IDENTIFIER ::= { upsMIB 2 }
+
+-- This section defines the well-known notifications sent by
+-- UPS agents.
+-- Care must be taken to insure that no particular notification
+-- is sent to a single receiving entity more often than once
+-- every five seconds.
+
+upsTrapOnBattery NOTIFICATION-TYPE
+    OBJECTS { upsEstimatedMinutesRemaining, upsSecondsOnBattery,
+              upsConfigLowBattTime }
+    STATUS  current
+    DESCRIPTION
+            "The UPS is operating on battery power.  This trap is
+            persistent and is resent at one minute intervals until
+            the UPS either turns off or is no longer running on
+            battery."
+  ::= { upsTraps 1 }
+
+upsTrapTestCompleted NOTIFICATION-TYPE
+    OBJECTS { upsTestId, upsTestSpinLock,
+              upsTestResultsSummary, upsTestResultsDetail,
+              upsTestStartTime, upsTestElapsedTime }
+    STATUS  current
+    DESCRIPTION
+            "This trap is sent upon completion of a UPS diagnostic
+            test."
+  ::= { upsTraps 2 }
+
+upsTrapAlarmEntryAdded NOTIFICATION-TYPE
+    OBJECTS { upsAlarmId, upsAlarmDescr }
+    STATUS  current
+    DESCRIPTION
+            "This trap is sent each time an alarm is inserted into
+            to the alarm table.  It is sent on the insertion of
+            all alarms except for upsAlarmOnBattery and
+            upsAlarmTestInProgress."
+  ::= { upsTraps 3 }
+
+upsTrapAlarmEntryRemoved NOTIFICATION-TYPE
+    OBJECTS { upsAlarmId, upsAlarmDescr }
+    STATUS  current
+    DESCRIPTION
+            "This trap is sent each time an alarm is removed from
+            the alarm table.  It is sent on the removal of all
+            alarms except for upsAlarmTestInProgress."
+  ::= { upsTraps 4 }
+
+
+--
+-- conformance information
+--
+upsConformance        OBJECT IDENTIFIER ::= { upsMIB 3 }
+
+upsCompliances        OBJECT IDENTIFIER ::= { upsConformance 1 }
+
+
+--
+-- compliance statements
+--
+
+upsSubsetCompliance MODULE-COMPLIANCE
+    STATUS     current
+    DESCRIPTION
+
+            "The compliance statement for UPSs that only support
+            the two-contact communication protocol."
+    MODULE -- this module
+        MANDATORY-GROUPS  { upsSubsetIdentGroup,
+                  upsSubsetBatteryGroup, upsSubsetInputGroup,
+                  upsSubsetOutputGroup, upsSubsetAlarmGroup,
+                  upsSubsetControlGroup, upsSubsetConfigGroup }
+
+    OBJECT     upsBatteryStatus
+    SYNTAX     INTEGER {
+        batteryNormal(2),
+        batteryLow(3)
+    }
+    DESCRIPTION
+            "Support of the values unknown(1) and
+            batteryDepleted(4) is not required."
+
+    OBJECT     upsAlarmDescr
+    DESCRIPTION
+            "Support of all `well known' alarm types is not
+            required.  The well known alarm types which must be
+            supported are: upsAlarmOnBattery, upsAlarmLowBattery,
+            upsAlarmInputBad, upsAlarmUpsOutputOff,
+            upsAlarmUpsSystemOff, and upsAlarmTestInProgress."
+
+    OBJECT     upsOutputSource
+    SYNTAX     INTEGER {
+        normal(2),
+        battery(4)
+    }
+    DESCRIPTION
+            "Support of the values other(1), none(2), bypass(4),
+            booster(6) and reducer(7) is not required."
+
+    OBJECT     upsShutdownType
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one shutdown type."
+
+    OBJECT     upsAutoRestart
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one restart type."
+
+    OBJECT     upsConfigInputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigInputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+    ::= { upsCompliances 1 }
+
+upsBasicCompliance MODULE-COMPLIANCE
+    STATUS     current
+    DESCRIPTION
+
+            "The compliance statement for UPSs that support
+            full-featured functions, such as control."
+    MODULE -- this module
+        MANDATORY-GROUPS { upsBasicIdentGroup,
+                  upsBasicBatteryGroup, upsBasicInputGroup,
+                  upsBasicOutputGroup, upsBasicAlarmGroup,
+                  upsBasicTestGroup, upsBasicControlGroup,
+                  upsBasicConfigGroup }
+
+
+    OBJECT     upsAlarmDescr
+    DESCRIPTION
+            "Support of all `well known' alarm types is not
+            required.  The well known alarm types which must be
+            supported are: upsAlarmOnBattery, upsAlarmLowBattery,
+            upsAlarmDepletedBattery, upsAlarmTempBad,
+            upsAlarmInputBad, upsAlarmOutputOverload,
+            upsAlarmOnBypass, upsAlarmBypassBad,
+            upsAlarmOutputOffAsRequested,
+            upsAlarmUpsOffAsRequested, upsAlarmUpsOutputOff,
+            upsAlarmUpsSystemOff, upsAlarmGeneralFault,
+            upsAlarmDiagnosticTestFailed,
+            upsAlarmCommunicationsLost, upsAlarmShutdownPending,
+            and upsAlarmTestInProgress."
+
+    OBJECT     upsTestId
+    DESCRIPTION
+            "Support of all `well known' test types is not
+            required.  If no tests are supported, then the only
+            well known test type which must be supported is
+            upsTestNoTestsInitiated."
+
+    OBJECT     upsOutputSource
+    SYNTAX     INTEGER {
+        normal(2),
+        battery(4)
+    }
+    DESCRIPTION
+            "Support of the values other(1), none(2), bypass(4),
+            booster(6) and reducer(7) is not required."
+
+        GROUP upsBasicBypassGroup
+        DESCRIPTION
+            "The upsBasicBypassGroup is only required for UPSs
+            that have a Bypass present."
+    OBJECT     upsShutdownType
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one shutdown type."
+
+    OBJECT     upsAutoRestart
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one restart type."
+
+    OBJECT     upsConfigInputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigInputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigLowBattTime
+    DESCRIPTION
+            "Implementation of all possible values may be onerous
+            for some systems.  Consequently, not all possible
+            values must be supported.  However, at least two
+            different manufacturer-selected values must be
+            supported."
+
+    ::= { upsCompliances 2 }
+
+upsFullCompliance MODULE-COMPLIANCE
+    STATUS     current
+    DESCRIPTION
+            "The compliance statement for UPSs that support
+            advanced full-featured functions."
+    MODULE -- this module
+        MANDATORY-GROUPS { upsFullIdentGroup, upsFullBatteryGroup,
+                  upsFullInputGroup, upsFullOutputGroup,
+                  upsFullAlarmGroup, upsFullTestGroup,
+                  upsFullControlGroup, upsFullConfigGroup }
+
+    OBJECT     upsAlarmDescr
+    DESCRIPTION
+            "Support of all `well known' alarm types is not
+            required.  The well known alarm types which must be
+            supported are: upsAlarmBatteryBad, upsAlarmOnBattery,
+            upsAlarmLowBattery, upsAlarmDepletedBattery,
+            upsAlarmTempBad, upsAlarmInputBad, upsAlarmOnBypass,
+            upsAlarmBypassBad, upsAlarmOutputOffAsRequested,
+            upsAlarmUpsOffAsRequested, upsAlarmUpsOutputOff,
+            upsAlarmUpsSystemOff, upsAlarmGeneralFault,
+            upsAlarmDiagnosticTestFailed,
+            upsAlarmCommunicationsLost, upsAlarmShutdownPending,
+            and upsAlarmTestInProgress."
+
+    OBJECT     upsTestId
+    DESCRIPTION
+            "Support of all `well known' test types is not
+            required.  The well known test types which must be
+            supported are: upsTestNoTestsInitiated,
+            upsTestGeneralSystemsTest, and
+            upsTestQuickBatteryTest."
+
+    OBJECT     upsOutputSource
+    SYNTAX     INTEGER {
+        normal(2),
+        battery(4)
+    }
+    DESCRIPTION
+            "Support of the values other(1), none(2), bypass(4),
+            booster(6) and reducer(7) is not required."
+
+        GROUP upsFullBypassGroup
+        DESCRIPTION
+            "The upsFullBypassGroup is only required for UPSs that
+            have a Bypass present."
+
+    OBJECT     upsShutdownType
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one shutdown type."
+
+    OBJECT     upsAutoRestart
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required, i.e., compliant
+            systems need not support more than one restart type."
+
+    OBJECT     upsConfigInputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigInputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputVoltage
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigOutputFreq
+    MIN-ACCESS read-only
+    DESCRIPTION
+            "Read-write access is not required."
+
+    OBJECT     upsConfigLowBattTime
+    DESCRIPTION
+            "Implementation of all possible values may be onerous
+            for some systems.  Consequently, not all possible
+            values must be supported.  However, at least two
+            different manufacturer-selected values must be
+            supported."
+
+    ::= { upsCompliances 3 }
+
+
+--
+-- units of conformance
+--
+
+-- summary at a glance:
+
+--                                      subset  basic   adv
+--upsIdentManufacturer                  x       x       x
+--upsIdentModel                         x       x       x
+
+--upsIdentUPSSoftwareVersion                    x       x
+--upsIdentAgentSoftwareVersion          x       x       x
+--upsIdentName                          x       x       x
+--upsIdentAttachedDevices               x               x
+--
+--upsBatteryStatus                      x       x       x  notes
+--upsSecondsOnBattery                   x       x       x
+--upsEstimatedMinutesRemaining                          x
+--upsEstimatedChargeRemaining                           x
+--upsBatteryVoltage
+--upsBatteryCurrent
+--upsBatteryTemperature
+--
+--upsInputLineBads                      x       x       x
+--upsInputNumLines                              x       x
+--upsInputFrequency                             x       x
+--upsInputVoltage                               x       x
+--upsInputCurrent
+--upsInputTruePower
+--
+--upsOutputSource                       x       x       x  notes
+--upsOutputFrequency                            x       x
+--upsOutputNumLines                             x       x
+--upsOutputVoltage                              x       x
+--upsOutputCurrent                                      x
+--upsOutputPower                                        x
+--upsOutputPercentLoad                                  x
+--
+--
+--upsBypassFrequency                            x       x  notes
+--upsBypassNumLines                             x       x
+--upsBypassVoltage                              x       x
+--upsBypassCurrent
+--upsBypassPower
+--
+--
+--upsAlarmsPresent                      x       x       x
+--upsAlarmDescr                         x       x       x  notes
+--upsAlarmTime                          x       x       x
+--
+--upsTestId                                     x       x  notes
+--upsTestSpinLock                               x       x
+--upsTestResultsSummary                         x       x
+--upsTestResultsDetail                          x       x
+--upsTestStartTime                              x       x
+--upsTestElapsedTime                            x       x
+--
+--upsShutdownType                       x       x       x  notes
+
+--upsShutdownAfterDelay                 x       x       x
+--upsStartupAfterDelay                          x       x
+--upsRebootWithDuration                         x       x
+--upsAutoRestart                        x       x       x  notes
+--
+--upsConfigInputVoltage                 x       x       x  notes
+--upsConfigInputFreq                    x       x       x  notes
+--upsConfigOutputVoltage                x       x       x  notes
+--upsConfigOutputFreq                   x       x       x  notes
+--upsConfigOutputVA                     x       x       x
+--upsConfigOutputPower                  x       x       x
+--upsConfigLowBattTime                          x       x  notes
+--upsConfigAudibleStatus                        x       x
+--upsConfigLowVoltageTransferPoint
+--upsConfigHighVoltageTransferPoint
+
+
+-- units of conformance
+upsGroups             OBJECT IDENTIFIER ::= { upsConformance 2 }
+
+upsSubsetGroups       OBJECT IDENTIFIER ::= { upsGroups 1 }
+
+upsSubsetIdentGroup OBJECT-GROUP
+    OBJECTS { upsIdentManufacturer, upsIdentModel,
+              upsIdentAgentSoftwareVersion, upsIdentName,
+              upsIdentAttachedDevices }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetIdentGroup defines objects which are
+            common across all UPSs which meet subset compliance.
+            Most devices which conform to the upsSubsetIdentGroup
+            will provide access to these objects via a proxy
+            agent.  If the proxy agent is compatible with multiple
+            UPS types, configuration of the proxy agent will
+            require specifying some of these values, either
+            individually, or as a group (perhaps through a table
+            lookup mechanism based on the UPS model number)."
+    ::= { upsSubsetGroups 1 }
+
+upsSubsetBatteryGroup OBJECT-GROUP
+    OBJECTS { upsBatteryStatus, upsSecondsOnBattery }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetBatteryGroup defines the objects that
+            are common to battery groups of two-contact UPSs."
+    ::= { upsSubsetGroups 2 }
+
+upsSubsetInputGroup OBJECT-GROUP
+    OBJECTS { upsInputLineBads }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetInputGroup defines the objects that are
+            common to the Input groups of two-contact UPSs."
+    ::= { upsSubsetGroups 3 }
+
+upsSubsetOutputGroup OBJECT-GROUP
+    OBJECTS { upsOutputSource }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetOutputGroup defines the objects that are
+            common to the Output groups of two-contact UPSs."
+    ::= { upsSubsetGroups 4 }
+
+
+-- { upsSubsetGroups 5 } is reserved for
+-- future use (upsSubsetBypassGroup)
+
+upsSubsetAlarmGroup OBJECT-GROUP
+    OBJECTS { upsAlarmsPresent, upsAlarmDescr, upsAlarmTime }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetAlarmGroup defines the objects that are
+            common to the Alarm groups of two-contact UPSs."
+    ::= { upsSubsetGroups 6 }
+
+-- { upsSubsetGroups 7 } is reserved for
+-- future use (upsSubsetTestGroup)
+
+upsSubsetControlGroup OBJECT-GROUP
+    OBJECTS { upsShutdownType, upsShutdownAfterDelay,
+                  upsAutoRestart }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetControlGroup defines the objects that
+            are common to the Control groups of two-contact UPSs."
+    ::= { upsSubsetGroups 8 }
+
+upsSubsetConfigGroup OBJECT-GROUP
+    OBJECTS { upsConfigInputVoltage, upsConfigInputFreq,
+              upsConfigOutputVoltage, upsConfigOutputFreq,
+              upsConfigOutputVA, upsConfigOutputPower }
+    STATUS  current
+    DESCRIPTION
+            "The upsSubsetConfigGroup defines the objects that are
+            common to the Config groups of two-contact UPSs."
+    ::= { upsSubsetGroups 9 }
+upsBasicGroups        OBJECT IDENTIFIER ::= { upsGroups 2 }
+
+upsBasicIdentGroup OBJECT-GROUP
+    OBJECTS { upsIdentManufacturer, upsIdentModel,
+              upsIdentUPSSoftwareVersion,
+              upsIdentAgentSoftwareVersion, upsIdentName }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicIdentGroup defines objects which are
+            common to the Ident group of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 1 }
+
+upsBasicBatteryGroup OBJECT-GROUP
+    OBJECTS { upsBatteryStatus, upsSecondsOnBattery }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicBatteryGroup defines the objects that are
+            common to the battery groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 2 }
+
+upsBasicInputGroup OBJECT-GROUP
+    OBJECTS { upsInputLineBads, upsInputNumLines,
+              upsInputFrequency, upsInputVoltage }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicInputGroup defines the objects that are
+            common to the Input groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 3 }
+
+upsBasicOutputGroup OBJECT-GROUP
+    OBJECTS { upsOutputSource, upsOutputFrequency,
+              upsOutputNumLines, upsOutputVoltage }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicOutputGroup defines the objects that are
+            common to the Output groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 4 }
+
+upsBasicBypassGroup OBJECT-GROUP
+    OBJECTS { upsBypassFrequency, upsBypassNumLines,
+              upsBypassVoltage }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicBypassGroup defines the objects that are
+            common to the Bypass groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 5 }
+
+upsBasicAlarmGroup OBJECT-GROUP
+    OBJECTS { upsAlarmsPresent, upsAlarmDescr, upsAlarmTime }
+    STATUS  current
+    DESCRIPTION
+
+            "The upsBasicAlarmGroup defines the objects that are
+            common to the Alarm  groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 6 }
+
+upsBasicTestGroup OBJECT-GROUP
+    OBJECTS { upsTestId, upsTestSpinLock,
+              upsTestResultsSummary, upsTestResultsDetail,
+              upsTestStartTime, upsTestElapsedTime }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicTestGroup defines the objects that are
+            common to the Test groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 7 }
+
+upsBasicControlGroup OBJECT-GROUP
+    OBJECTS { upsShutdownType, upsShutdownAfterDelay,
+              upsStartupAfterDelay, upsRebootWithDuration,
+              upsAutoRestart }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicControlGroup defines the objects that are
+            common to the Control groups of compliant UPSs which
+            support basic functions."
+    ::= { upsBasicGroups 8 }
+
+upsBasicConfigGroup OBJECT-GROUP
+    OBJECTS { upsConfigInputVoltage, upsConfigInputFreq,
+              upsConfigOutputVoltage, upsConfigOutputFreq,
+              upsConfigOutputVA, upsConfigOutputPower,
+              upsConfigLowBattTime, upsConfigAudibleStatus }
+    STATUS  current
+    DESCRIPTION
+            "The upsBasicConfigGroup defines the objects that are
+            common to the Config groups of UPSs which support
+            basic functions."
+    ::= { upsBasicGroups 9 }
+upsFullGroups         OBJECT IDENTIFIER ::= { upsGroups 3 }
+
+upsFullIdentGroup OBJECT-GROUP
+    OBJECTS { upsIdentManufacturer, upsIdentModel,
+              upsIdentUPSSoftwareVersion,
+              upsIdentAgentSoftwareVersion, upsIdentName,
+              upsIdentAttachedDevices }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullIdentGroup defines objects which are
+            common to the Ident group of fully compliant UPSs."
+    ::= { upsFullGroups 1 }
+
+upsFullBatteryGroup OBJECT-GROUP
+    OBJECTS { upsBatteryStatus, upsSecondsOnBattery,
+              upsEstimatedMinutesRemaining,
+              upsEstimatedChargeRemaining }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullBatteryGroup defines the objects that are
+            common to the battery groups of fully compliant UPSs."
+    ::= { upsFullGroups 2 }
+
+upsFullInputGroup OBJECT-GROUP
+    OBJECTS { upsInputLineBads, upsInputNumLines,
+              upsInputFrequency, upsInputVoltage }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullInputGroup defines the objects that are
+            common to the Input groups of fully compliant UPSs."
+    ::= { upsFullGroups 3 }
+
+upsFullOutputGroup OBJECT-GROUP
+    OBJECTS { upsOutputSource, upsOutputFrequency,
+              upsOutputNumLines, upsOutputVoltage,
+              upsOutputCurrent, upsOutputPower,
+              upsOutputPercentLoad }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullOutputGroup defines the objects that are
+            common to the Output groups of fully compliant UPSs."
+    ::= { upsFullGroups 4 }
+
+upsFullBypassGroup OBJECT-GROUP
+    OBJECTS { upsBypassFrequency, upsBypassNumLines,
+              upsBypassVoltage }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullBypassGroup defines the objects that are
+            common to the Bypass groups of fully compliant UPSs."
+    ::= { upsFullGroups 5 }
+
+upsFullAlarmGroup OBJECT-GROUP
+    OBJECTS { upsAlarmsPresent, upsAlarmDescr, upsAlarmTime }
+    STATUS  current
+    DESCRIPTION
+
+            "The upsFullAlarmGroup defines the objects that are
+            common to the Alarm  groups of fully compliant UPSs."
+    ::= { upsFullGroups 6 }
+
+upsFullTestGroup OBJECT-GROUP
+    OBJECTS { upsTestId, upsTestSpinLock,
+              upsTestResultsSummary, upsTestResultsDetail,
+              upsTestStartTime, upsTestElapsedTime }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullTestGroup defines the objects that are
+            common to the Test groups of fully compliant UPSs."
+    ::= { upsFullGroups 7 }
+
+upsFullControlGroup OBJECT-GROUP
+    OBJECTS { upsShutdownType, upsShutdownAfterDelay,
+              upsStartupAfterDelay, upsRebootWithDuration,
+              upsAutoRestart }
+    STATUS  current
+    DESCRIPTION
+"The upsFullControlGroup defines the objects that are
+common to the Control groups of fully compliant UPSs."
+    ::= { upsFullGroups 8 }
+
+upsFullConfigGroup OBJECT-GROUP
+    OBJECTS { upsConfigInputVoltage, upsConfigInputFreq,
+              upsConfigOutputVoltage, upsConfigOutputFreq,
+              upsConfigOutputVA, upsConfigOutputPower,
+              upsConfigLowBattTime, upsConfigAudibleStatus }
+    STATUS  current
+    DESCRIPTION
+            "The upsFullConfigGroup defines the objects that are
+            common to the Config groups of fully compliant UPSs."
+    ::= { upsFullGroups 9 }
+
+END