diff options
Diffstat (limited to 'MIBS/ISDN-MIB')
| -rw-r--r-- | MIBS/ISDN-MIB | 1263 |
1 files changed, 1263 insertions, 0 deletions
diff --git a/MIBS/ISDN-MIB b/MIBS/ISDN-MIB new file mode 100644 index 0000000..ceb8978 --- /dev/null +++ b/MIBS/ISDN-MIB @@ -0,0 +1,1263 @@ +-- ***************************************************************** +-- RFC2127-MIB.my: ISDN MIB file +-- +-- April 1998, Viet Nguyen +-- +-- Copyright (c) 1998 by cisco Systems, Inc. +-- All rights reserved. +-- +-- ***************************************************************** +-- +-- This mib was extracted from RFC 2127 + + +ISDN-MIB DEFINITIONS ::= BEGIN + +IMPORTS + MODULE-IDENTITY, + NOTIFICATION-TYPE, + OBJECT-TYPE, + Counter32, + Gauge32, + Integer32 + FROM SNMPv2-SMI + DisplayString, + TruthValue, + TimeStamp, + RowStatus, + TestAndIncr, + TEXTUAL-CONVENTION + FROM SNMPv2-TC + MODULE-COMPLIANCE, + OBJECT-GROUP +-- NOTIFICATION-GROUP + FROM SNMPv2-CONF + ifIndex, + InterfaceIndex + FROM IF-MIB + IANAifType + FROM IANAifType-MIB + transmission + FROM RFC1213-MIB; + +isdnMib MODULE-IDENTITY + LAST-UPDATED "9609231642Z" -- Sep 23, 1996 + ORGANIZATION "IETF ISDN MIB Working Group" + CONTACT-INFO + " Guenter Roeck + Postal: cisco Systems + 170 West Tasman Drive + San Jose, CA 95134 + U.S.A. + Phone: +1 408 527 3143 + E-mail: groeck@cisco.com" + DESCRIPTION + "The MIB module to describe the + management of ISDN interfaces." + ::= { transmission 20 } + +-- The ISDN hardware interface (BRI or PRI) is represented +-- by a media specific ifEntry. +-- +-- For basic rate lines, the media specifics for the physical interface +-- is defined in the physical interface group of the ISDN MIB. +-- The ifType for physical basic rate interfaces is isdns(75) +-- or isdnu(76), whichever is appropriate. +-- +-- For primary rate, the media specifics are defined in the Trunk +-- MIB and the ifType has a value of ds1(18). + +-- Each signaling channel is represented by an entry +-- in the isdnSignalingTable. +-- The signaling channel has an ifType value of isdn(63). +-- Each B channel is also represented as an entry +-- in the ifTable. The B channels have an ifType value +-- of ds0(81). +-- This model is used while defining objects and tables +-- for management. +-- The ISDN MIB allows sub-layers. For example, the data transfer +-- over a B channel may take place with PPP encapsulation. While the +-- ISDN MIB describes the D and B channels, a media specific MIB +-- for PPP can be used on a layered basis. This is as per +-- the interfaces MIB. + +-- Textual conventions + +IsdnSignalingProtocol ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "This data type is used as the syntax of the + isdnSignalingProtocol object in the + definition of ISDN-MIB's isdnSignalingTable. + + The definition of this textual convention with the + addition of newly assigned values is published + periodically by the IANA, in either the Assigned + Numbers RFC, or some derivative of it specific to + Internet Network Management number assignments. (The + latest arrangements can be obtained by contacting the + IANA.) + + Requests for new values should be made to IANA via + email (iana@iana.org)." + SYNTAX INTEGER { + other(1), -- none of the following + dss1(2), -- ITU DSS1 (formerly CCITT) Q.931 + etsi(3), -- Europe / ETSI ETS300-102 + -- plus supplementary services + -- (ETSI 300-xxx) + -- note that NET3, NET5 define + -- test procedures for ETS300-102 + -- and have been replaced by + -- I-CTR 3 and I-CTR 4. + dass2(4), -- U.K. / DASS2 (PRI) + ess4(5), -- U.S.A. / AT&T 4ESS + ess5(6), -- U.S.A. / AT&T 5ESS + dms100(7), -- U.S.A. / Northern Telecom DMS100 + dms250(8), -- U.S.A. / Northern Telecom DMS250 + ni1(9), -- U.S.A. / National ISDN 1 (BRI) + ni2(10), -- U.S.A. / National ISDN 2 (BRI, PRI) + ni3(11), -- U.S.A. / next one + vn2(12), -- France / VN2 + vn3(13), -- France / VN3 + vn4(14), -- France / VN4 (ETSI with changes) + vn6(15), -- France / VN6 (ETSI with changes) + -- delta document CSE P 10-21 A + -- test document CSE P 10-20 A + kdd(16), -- Japan / KDD + ins64(17), -- Japan / NTT INS64 + ins1500(18), -- Japan / NTT INS1500 + itr6(19), -- Germany/ 1TR6 (BRI, PRI) + cornet(20), -- Germany/ Siemens HiCom CORNET + ts013(21), -- Australia / TS013 + -- (formerly TPH 1962, BRI) + ts014(22), -- Australia / TS014 + -- (formerly TPH 1856, PRI) + qsig(23), -- Q.SIG + swissnet2(24), -- SwissNet-2 + swissnet3(25) -- SwissNet-3 + } + +-- Isdn Mib objects definitions + +isdnMibObjects OBJECT IDENTIFIER ::= { isdnMib 1 } + +-- ISDN physical interface group + +-- This group describes physical basic rate interfaces. + +isdnBasicRateGroup OBJECT IDENTIFIER ::= { isdnMibObjects 1 } + +isdnBasicRateTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnBasicRateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Table containing configuration and operational + parameters for all physical Basic Rate + interfaces on this managed device." + ::= { isdnBasicRateGroup 1 } + +isdnBasicRateEntry OBJECT-TYPE + SYNTAX IsdnBasicRateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the ISDN Basic Rate Table." + INDEX { ifIndex } + ::= { isdnBasicRateTable 1 } + +IsdnBasicRateEntry ::= SEQUENCE { + isdnBasicRateIfType INTEGER, + isdnBasicRateLineTopology INTEGER, + isdnBasicRateIfMode INTEGER, + isdnBasicRateSignalMode INTEGER + } + +isdnBasicRateIfType OBJECT-TYPE + SYNTAX INTEGER { + isdns(75), + isdnu(76) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The physical interface type. For 'S/T' interfaces, + also called 'Four-wire Basic Access Interface', + the value of this object is isdns(75). + For 'U' interfaces, also called 'Two-wire Basic + Access Interface', the value of this object is + isdnu(76)." + ::= { isdnBasicRateEntry 1 } + +isdnBasicRateLineTopology OBJECT-TYPE + SYNTAX INTEGER { + pointToPoint(1), + pointToMultipoint(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The line topology to be used for this interface. + Note that setting isdnBasicRateIfType to isdns(75) + does not necessarily mean a line topology of + point-to-multipoint." + ::= { isdnBasicRateEntry 2 } + +isdnBasicRateIfMode OBJECT-TYPE + SYNTAX INTEGER { + te(1), + nt(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The physical interface mode. For TE mode, the value + of this object is te(1). For NT mode, the value + of this object is nt(2)." + ::= { isdnBasicRateEntry 3 } + +isdnBasicRateSignalMode OBJECT-TYPE + SYNTAX INTEGER { + active(1), + inactive(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The signaling channel operational mode for this interface. + If active(1) there is a signaling channel on this + interface. If inactive(2) a signaling channel is + not available." + ::= { isdnBasicRateEntry 4 } + +-- The B channel (bearer channel) group + +-- Note that disconnects can explicitely be handled using the +-- ifStack table. If a connection is to be disconnected, +-- the according ifStack entry has to be removed. +-- More specifically, the ifStackTable entry which binds the high-layer +-- ifTable entry (and related dialCtlNbrCfgTable entry) to the +-- B channel ifTable entry (and related isdnBearerTable entry) +-- during an active call has to be removed. + +isdnBearerGroup OBJECT IDENTIFIER ::= { isdnMibObjects 2 } + +isdnBearerTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnBearerEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table defines port specific operational, statistics + and active call data for ISDN B channels. Each entry + in this table describes one B (bearer) channel." + ::= { isdnBearerGroup 1 } + +isdnBearerEntry OBJECT-TYPE + SYNTAX IsdnBearerEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Operational and statistics information relating to + one port. A port is a single B channel." + INDEX { ifIndex } + ::= { isdnBearerTable 1 } + +IsdnBearerEntry ::= + SEQUENCE { + isdnBearerChannelType INTEGER, + isdnBearerOperStatus INTEGER, + isdnBearerChannelNumber INTEGER, + isdnBearerPeerAddress DisplayString, + isdnBearerPeerSubAddress DisplayString, + isdnBearerCallOrigin INTEGER, + isdnBearerInfoType INTEGER, + isdnBearerMultirate TruthValue, + isdnBearerCallSetupTime TimeStamp, + isdnBearerCallConnectTime TimeStamp, + isdnBearerChargedUnits Gauge32 + } + +isdnBearerChannelType OBJECT-TYPE + SYNTAX INTEGER { + dialup(1), + leased(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The B channel type. If the B channel is connected + to a dialup line, this object has a value of + dialup(1). In this case, it is controlled by + an associated signaling channel. If the B channel + is connected to a leased line, this object has + a value of leased(2). For leased line B channels, there + is no signaling channel control available." + ::= { isdnBearerEntry 1 } + +isdnBearerOperStatus OBJECT-TYPE + SYNTAX INTEGER { + idle(1), + connecting(2), + connected(3), + active(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current call control state for this port. + idle(1): The B channel is idle. + No call or call attempt is going on. + connecting(2): A connection attempt (outgoing call) + is being made on this interface. + connected(3): An incoming call is in the process + of validation. + active(4): A call is active on this interface." + ::= { isdnBearerEntry 2 } + +isdnBearerChannelNumber OBJECT-TYPE + SYNTAX INTEGER (1..30) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The identifier being used by a signaling protocol + to identify this B channel, also referred to as + B channel number. If the Agent also supports the DS0 MIB, + the values of isdnBearerChannelNumber and dsx0Ds0Number + must be identical for a given B channel." + ::= { isdnBearerEntry 3 } + +isdnBearerPeerAddress OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ISDN address the current or last call is or was + connected to. + + In some cases, the format of this information can not + be predicted, since it largely depends on the type + of switch or PBX the device is connected to. Therefore, + the detailed format of this information is not + specified and is implementation dependent. + + If possible, the agent should supply this information + using the E.164 format. In this case, the number must + start with '+'. Otherwise, IA5 number digits must be used. + + If the peer ISDN address is not available, + this object has a length of zero." + REFERENCE + "ITU-T E.164, Q.931 chapter 4.5.10" + ::= { isdnBearerEntry 4 } + +isdnBearerPeerSubAddress OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ISDN subaddress the current or last call is or was + connected to. + + The subaddress is an user supplied string of up to 20 + IA5 characters and is transmitted transparently through + the network. + + If the peer subaddress is not available, this object + has a length of zero." + REFERENCE + "ITU-T I.330, Q.931 chapter 4.5.11" + ::= { isdnBearerEntry 5 } + +isdnBearerCallOrigin OBJECT-TYPE + SYNTAX INTEGER { + unknown(1), + originate(2), + answer(3), + callback(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The call origin for the current or last call. If since + system startup there was no call on this interface, + this object has a value of unknown(1)." + ::= { isdnBearerEntry 6 } + +isdnBearerInfoType OBJECT-TYPE + SYNTAX INTEGER { + unknown(1), + speech(2), + unrestrictedDigital(3), -- as defined in Q.931 + unrestrictedDigital56(4), -- with 56k rate adaption + restrictedDigital(5), + audio31(6), -- 3.1 kHz audio + audio7(7), -- 7 kHz audio + video(8), + packetSwitched(9) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Information Transfer Capability for the current + or last call. + + speech(2) refers to a non-data connection, whereas + audio31(6) and audio7(7) refer to data mode connections. + + Note that Q.931, chapter 4.5.5, originally defined + audio7(7) as '7 kHz audio' and now defines it as + 'Unrestricted digital information with tones/ + announcements'. + + If since system startup there has been no call on this + interface, this object has a value of unknown(1)." + REFERENCE + "Q.931 [8], chapter 4.5.5, octet 3 of bearer capability + information element, combined with the User Rate + (as defined in octets 5 and 5a to 5d), if rate adaption + is being used." + ::= { isdnBearerEntry 7 } + +isdnBearerMultirate OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This flag indicates if the current or last call used + multirate. The actual information transfer rate, + in detail specified in octet 4.1 (rate multiplier), + is the sum of all B channel ifSpeed values for + the hyperchannel. + + If since system startup there was no call on this + interface, this object has a value of false(2)." + REFERENCE + "Q.931 [8], chapter 4.5.5." + ::= { isdnBearerEntry 8 } + +isdnBearerCallSetupTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime when the ISDN setup message for + the current or last call was sent or received. If since + system startup there has been no call on this interface, + this object has a value of zero." + ::= { isdnBearerEntry 9 } + +isdnBearerCallConnectTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime when the ISDN connect message for + the current or last call was sent or received. If since + system startup there has been no call on this interface, + this object has a value of zero." + ::= { isdnBearerEntry 10 } + +isdnBearerChargedUnits OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of charged units for the current or last + connection. For incoming calls or if charging information + is not supplied by the switch, the value of this object + is zero." + ::= { isdnBearerEntry 11 } + +-- ISDN signaling group + +isdnSignalingGroup OBJECT IDENTIFIER ::= { isdnMibObjects 3 } + +-- signaling channel configuration table +-- There is one entry in this table for each Terminal Endpoint +-- (link layer connection to the switch). +-- Usually, there is one endpoint per D channel. In some +-- cases, however, there can be multiple endpoints. +-- Thus, entries in this table can be created and deleted. +-- This also means the creation of an associated ifEntry. +-- +-- D channel backup and NFAS trunks are handled using the +-- ifStack table. +-- In case of D channel backup, there are multiple +-- Data Link Layer (LAPD) interfaces. Only one interface is +-- active; all others are dormant(5). +-- In case of NFAS trunks, one lower interface is the +-- LAPD interface, while the other lower interfaces are physical +-- interfaces. + +-- If directory number and calling address differ from each other +-- or multiple directory numbers are being used, +-- the isdnDirectoryTable has to be used to enter such +-- directory numbers. + +isdnSignalingGetIndex OBJECT-TYPE + SYNTAX TestAndIncr + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The recommended procedure for selecting a new index for + isdnSignalingTable row creation is to GET the value of + this object, and then to SET the object with the same + value. If the SET operation succeeds, the manager can use + this value as an index to create a new row in this table." + REFERENCE + "RFC1903, TestAndIncr textual convention." + ::= { isdnSignalingGroup 1 } + +isdnSignalingTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnSignalingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "ISDN signaling table containing configuration and + operational parameters for all ISDN signaling + channels on this managed device." + ::= { isdnSignalingGroup 2 } + +isdnSignalingEntry OBJECT-TYPE + SYNTAX IsdnSignalingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the ISDN Signaling Table. To create a new + entry, only isdnSignalingProtocol needs to be specified + before isdnSignalingStatus can become active(1)." + INDEX { isdnSignalingIndex } + ::= { isdnSignalingTable 1 } + +IsdnSignalingEntry ::= SEQUENCE { + isdnSignalingIndex INTEGER, + isdnSignalingIfIndex InterfaceIndex, + isdnSignalingProtocol IsdnSignalingProtocol, + isdnSignalingCallingAddress DisplayString, + isdnSignalingSubAddress DisplayString, + isdnSignalingBchannelCount Integer32, + isdnSignalingInfoTrapEnable INTEGER, + isdnSignalingStatus RowStatus + } + +isdnSignalingIndex OBJECT-TYPE + SYNTAX INTEGER (1..2147483647) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The index value which uniquely identifies an entry + in the isdnSignalingTable." + ::= { isdnSignalingEntry 1 } + +isdnSignalingIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ifIndex value of the interface associated with this + signaling channel." + ::= { isdnSignalingEntry 2 } + +isdnSignalingProtocol OBJECT-TYPE + SYNTAX IsdnSignalingProtocol + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The particular protocol type supported by the + switch providing access to the ISDN network + to which this signaling channel is connected." + ::= { isdnSignalingEntry 3 } + +isdnSignalingCallingAddress OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The ISDN Address to be assigned to this signaling + channel. More specifically, this is the 'Calling Address + information element' as being passed to the switch + in outgoing call setup messages. + + It can be an EAZ (1TR6), a calling number (DSS1, ETSI) + or any other number necessary to identify a signaling + interface. If there is no such number defined or required, + this is a zero length string. It is represented in + DisplayString form. + + Incoming calls can also be identified by this number. + If the Directory Number, i.e. the Called Number in + incoming calls, is different to this number, the + isdnDirectoryTable has to be used to specify all + possible Directory Numbers. + + The format of this information largely depends on the type + of switch or PBX the device is connected to. Therefore, + the detailed format of this information is not + specified and is implementation dependent. + + If possible, the agent should implement this information + using the E.164 number format. In this case, the number + must start with '+'. Otherwise, IA5 number digits must + be used." + REFERENCE + "ITU-T E.164, Q.931 chapter 4.5.10" + DEFVAL { "" } + ::= { isdnSignalingEntry 4 } + +isdnSignalingSubAddress OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Supplementary information to the ISDN address assigned + to this signaling channel. Usually, this is the + subaddress as defined in Q.931. + If there is no such number defined or required, this is + a zero length string. + The subaddress is used for incoming calls as well as + for outgoing calls. + The subaddress is an user supplied string of up to 20 + IA5 characters and is transmitted transparently through + the network." + REFERENCE + "ITU-T I.330, Q.931 chapter 4.5.11" + DEFVAL { "" } + ::= { isdnSignalingEntry 5 } + +isdnSignalingBchannelCount OBJECT-TYPE + SYNTAX Integer32 (1..65535) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The total number of B channels (bearer channels) + managed by this signaling channel. The default value + of this object depends on the physical interface type + and is either 2 for Basic Rate interfaces or + 24 (30) for Primary Rate interfaces." + ::= { isdnSignalingEntry 6 } + +isdnSignalingInfoTrapEnable OBJECT-TYPE + SYNTAX INTEGER { + enabled(1), + disabled(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether isdnMibCallInformation traps + should be generated for calls on this signaling + channel." + DEFVAL { disabled } + ::= { isdnSignalingEntry 7 } + +isdnSignalingStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create and delete rows in the + isdnSignalingTable." + ::= { isdnSignalingEntry 8 } + +-- Signaling channel statistics table +-- There is one entry for each signaling connection +-- in this table. +-- Note that the ifEntry also has some statistics information. + +isdnSignalingStatsTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnSignalingStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "ISDN signaling table containing statistics + information for all ISDN signaling channels + on this managed device. + Only statistical information which is not already being + counted in the ifTable is being defined in this table." + ::= { isdnSignalingGroup 3 } + +isdnSignalingStatsEntry OBJECT-TYPE + SYNTAX IsdnSignalingStatsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the ISDN Signaling statistics Table." + AUGMENTS { isdnSignalingEntry } + ::= { isdnSignalingStatsTable 1 } + +IsdnSignalingStatsEntry ::= SEQUENCE { + isdnSigStatsInCalls Counter32, + isdnSigStatsInConnected Counter32, + isdnSigStatsOutCalls Counter32, + isdnSigStatsOutConnected Counter32, + isdnSigStatsChargedUnits Counter32 + } + +isdnSigStatsInCalls OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of incoming calls on this interface." + ::= { isdnSignalingStatsEntry 1 } + +isdnSigStatsInConnected OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of incoming calls on this interface + which were actually connected." + ::= { isdnSignalingStatsEntry 2 } + +isdnSigStatsOutCalls OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of outgoing calls on this interface." + ::= { isdnSignalingStatsEntry 3 } + +isdnSigStatsOutConnected OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of outgoing calls on this interface + which were actually connected." + ::= { isdnSignalingStatsEntry 4 } + +isdnSigStatsChargedUnits OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of charging units on this interface since + system startup. + Only the charging units applying to the local interface, + i.e. for originated calls or for calls with 'Reverse + charging' being active, are counted here." + ::= { isdnSignalingStatsEntry 5 } + +-- +-- The LAPD table + +isdnLapdTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnLapdEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Table containing configuration and statistics + information for all LAPD (D channel Data Link) + interfaces on this managed device. + Only statistical information which is not already being + counted in the ifTable is being defined in this table." + ::= { isdnSignalingGroup 4 } + +isdnLapdEntry OBJECT-TYPE + SYNTAX IsdnLapdEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the LAPD Table." + INDEX { ifIndex } + ::= { isdnLapdTable 1 } + +IsdnLapdEntry ::= SEQUENCE { + isdnLapdPrimaryChannel TruthValue, + isdnLapdOperStatus INTEGER, + isdnLapdPeerSabme Counter32, + isdnLapdRecvdFrmr Counter32 + } + +isdnLapdPrimaryChannel OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "If set to true(1), this D channel is the designated + primary D channel if D channel backup is active. + There must be exactly one primary D channel + configured. If D channel backup is not used, this + object has a value of true(1)." + REFERENCE + "Q.931 [8], Annex F, D channel backup procedures." + ::= { isdnLapdEntry 1 } + +isdnLapdOperStatus OBJECT-TYPE + SYNTAX INTEGER { + inactive(1), + l1Active(2), + l2Active(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The operational status of this interface: + + inactive all layers are inactive + l1Active layer 1 is activated, + layer 2 datalink not established + l2Active layer 1 is activated, + layer 2 datalink established." + ::= { isdnLapdEntry 2 } + +isdnLapdPeerSabme OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of peer SABME frames received on this + interface. This is the number of peer-initiated + new connections on this interface." + ::= { isdnLapdEntry 3 } + +isdnLapdRecvdFrmr OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of LAPD FRMR response frames received. + This is the number of framing errors on this + interface." + ::= { isdnLapdEntry 4 } + +-- +-- Optional groups follow here. + +-- The Terminal Endpoint group and table + +-- This table is required only if TEI values or SPID numbers +-- have to be entered. +-- The ifIndex values for this table are identical to those of +-- the isdnSignalingChannel table. + +isdnEndpointGroup OBJECT IDENTIFIER ::= { isdnMibObjects 4 } + +isdnEndpointGetIndex OBJECT-TYPE + SYNTAX TestAndIncr + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The recommended procedure for selecting a new index for + isdnEndpointTable row creation is to GET the value of + this object, and then to SET the object with the same + value. If the SET operation succeeds, the manager can use + this value as an index to create a new row in this table." + REFERENCE + "RFC1903, TestAndIncr textual convention." + ::= { isdnEndpointGroup 1 } + +isdnEndpointTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnEndpointEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Table containing configuration for Terminal + Endpoints." + ::= { isdnEndpointGroup 2 } + +isdnEndpointEntry OBJECT-TYPE + SYNTAX IsdnEndpointEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the Terminal Endpoint Table. The value + of isdnEndpointIfType must be supplied for a row + in this table to become active." + INDEX { isdnEndpointIndex } + ::= { isdnEndpointTable 1 } + +IsdnEndpointEntry ::= SEQUENCE { + isdnEndpointIndex INTEGER, + isdnEndpointIfIndex InterfaceIndex, + isdnEndpointIfType IANAifType, + isdnEndpointTeiType INTEGER, + isdnEndpointTeiValue INTEGER, + isdnEndpointSpid DisplayString, + isdnEndpointStatus RowStatus + } + +isdnEndpointIndex OBJECT-TYPE + SYNTAX INTEGER (1..2147483647) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The index value which uniquely identifies an entry + in the isdnEndpointTable." + ::= { isdnEndpointEntry 1 } + +isdnEndpointIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ifIndex value of the interface associated with this + Terminal Endpoint." + ::= { isdnEndpointEntry 2 } + +isdnEndpointIfType OBJECT-TYPE + SYNTAX IANAifType + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The interface type for this Terminal Endpoint. + Interface types of x25ple(40) and isdn(63) are allowed. + The interface type is identical to the value of + ifType in the associated ifEntry." + ::= { isdnEndpointEntry 3 } + +isdnEndpointTeiType OBJECT-TYPE + SYNTAX INTEGER { + dynamic(1), + static(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The type of TEI (Terminal Endpoint Identifier) + used for this Terminal Endpoint. In case of dynamic(1), + the TEI value is selected by the switch. In + case of static(2), a valid TEI value has to be + entered in the isdnEndpointTeiValue object. + The default value for this object depends on the + interface type as well as the Terminal Endpoint type. + On Primary Rate interfaces the default value is + static(2). On Basic Rate interfaces the default value + is dynamic(1) for isdn(63) Terminal Endpoints and + static(2) for x25ple(40) Terminal Endpoints." + ::= { isdnEndpointEntry 4 } + +isdnEndpointTeiValue OBJECT-TYPE + SYNTAX INTEGER ( 0..255 ) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The TEI (Terminal Endpoint Identifier) value + for this Terminal Endpoint. If isdnEndpointTeiType + is set to static(2), valid numbers are 0..63, + while otherwise the value is set internally. + The default value of this object is 0 for static + TEI assignment. + The default value for dynamic TEI assignment is also + 0 as long as no TEI has been assigned. After TEI + assignment, the assigned TEI value is returned." + ::= { isdnEndpointEntry 5 } + +isdnEndpointSpid OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The Service profile IDentifier (SPID) information + for this Terminal Endpoint. + + The SPID is composed of 9-20 numeric characters. + + This information has to be defined in addition to + the local number for some switch protocol types, + e.g. Bellcore NI-1 and NI-2. + + If this object is not required, it is a + zero length string." + REFERENCE + "Bellcore SR-NWT-001953, Generic Guidelines for ISDN + Terminal Equipment on Basic Access Interfaces, + Chapter 8.5.1." + DEFVAL { "" } + ::= { isdnEndpointEntry 6 } + +isdnEndpointStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create and delete rows in the + isdnEndpointTable." + ::= { isdnEndpointEntry 7 } + +-- +-- The Directory Number group +-- + +isdnDirectoryGroup OBJECT IDENTIFIER ::= { isdnMibObjects 5 } + +isdnDirectoryTable OBJECT-TYPE + SYNTAX SEQUENCE OF IsdnDirectoryEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Table containing Directory Numbers." + ::= { isdnDirectoryGroup 1 } + +isdnDirectoryEntry OBJECT-TYPE + SYNTAX IsdnDirectoryEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in the Directory Number Table. All objects + in an entry must be set for a new row to become active." + INDEX { isdnDirectoryIndex } + ::= { isdnDirectoryTable 1 } + +IsdnDirectoryEntry ::= SEQUENCE { + isdnDirectoryIndex INTEGER, + isdnDirectoryNumber DisplayString, + isdnDirectorySigIndex INTEGER, + isdnDirectoryStatus RowStatus + } + +isdnDirectoryIndex OBJECT-TYPE + SYNTAX INTEGER ( 1..'7fffffff'h ) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The index value which uniquely identifies an entry + in the isdnDirectoryTable." + ::= { isdnDirectoryEntry 1 } + +isdnDirectoryNumber OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "A Directory Number. Directory Numbers are used + to identify incoming calls on the signaling + channel given in isdnDirectorySigIndex. + + The format of this information largely depends on the type + of switch or PBX the device is connected to. Therefore, + the detailed format of this information is not + specified and is implementation dependent. + + If possible, the agent should implement this information + using the E.164 number format. In this case, the number + must start with '+'. Otherwise, IA5 number digits must + be used." + REFERENCE + "ITU-T E.164, Q.931 chapter 4.5.10" + ::= { isdnDirectoryEntry 2 } + +isdnDirectorySigIndex OBJECT-TYPE + SYNTAX INTEGER (1..2147483647) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "An index pointing to an ISDN signaling channel. + Incoming calls are accepted on this + signaling channel if the isdnDirectoryNumber is + presented as Called Number in the SETUP message." + ::= { isdnDirectoryEntry 3 } + +isdnDirectoryStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object is used to create and delete rows in the + isdnDirectoryTable." + ::= { isdnDirectoryEntry 4 } + +-- Traps + +isdnMibTrapPrefix OBJECT IDENTIFIER ::= { isdnMib 2 } +isdnMibTraps OBJECT IDENTIFIER ::= { isdnMibTrapPrefix 0 } + +isdnMibCallInformation NOTIFICATION-TYPE + OBJECTS { + ifIndex, -- isdnBearerTable ifIndex + isdnBearerOperStatus, + isdnBearerPeerAddress, + isdnBearerPeerSubAddress, + isdnBearerCallSetupTime, + isdnBearerInfoType, + isdnBearerCallOrigin + } + STATUS current + DESCRIPTION + "This trap/inform is sent to the manager under the + following condidions: + - on incoming calls for each call which is rejected for + policy reasons (e.g. unknown neighbor or access + violation) + - on outgoing calls whenever a call attempt is determined + to have ultimately failed. In the event that call retry + is active, then this will be after all retry attempts + have failed. + - whenever a call connects. In this case, the object + isdnBearerCallConnectTime should be included in the + trap. + + Only one such trap is sent in between successful or + unsuccessful call attempts from or to a single neighbor; + subsequent call attempts result in no trap. + + If the Dial Control MIB objects dialCtlNbrCfgId and + dialCtlNbrCfgIndex are known by the entity generating + this trap, both objects should be included in the trap + as well. The receipt of this trap with no dial neighbor + information indicates that the manager must poll the + callHistoryTable of the Dial Control MIB to see what + changed." + ::= { isdnMibTraps 1 } + +-- +-- conformance information +-- + +isdnMibConformance OBJECT IDENTIFIER ::= { isdnMib 3 } +isdnMibCompliances OBJECT IDENTIFIER ::= { isdnMibConformance 1 } +isdnMibGroups OBJECT IDENTIFIER ::= { isdnMibConformance 2 } + +-- compliance statements + +isdnMibCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statement for entities which implement + the ISDN MIB." + MODULE -- this module + +-- unconditionally mandatory groups + MANDATORY-GROUPS { + isdnMibSignalingGroup, + isdnMibBearerGroup +-- isdnMibNotificationsGroup + } + +-- conditionally mandatory group + GROUP isdnMibBasicRateGroup + DESCRIPTION + "The isdnMibBasicRateGroup is mandatory for entities + supporting ISDN Basic Rate interfaces." + +-- optional groups + GROUP isdnMibEndpointGroup + DESCRIPTION + "Implementation of this group is optional for all systems + that attach to ISDN interfaces." + + GROUP isdnMibDirectoryGroup + DESCRIPTION + "Implementation of this group is optional for all systems + that attach to ISDN interfaces." + + OBJECT isdnBasicRateIfType + MIN-ACCESS read-only + DESCRIPTION + "It is conformant to implement this object as read-only." + + OBJECT isdnBasicRateLineTopology + MIN-ACCESS read-only + DESCRIPTION + "It is conformant to implement this object as read-only." + + OBJECT isdnBasicRateIfMode + MIN-ACCESS read-only + DESCRIPTION + "It is conformant to implement this object as read-only." + + OBJECT isdnBasicRateSignalMode + MIN-ACCESS read-only + DESCRIPTION + "It is conformant to implement this object as read-only." + ::= { isdnMibCompliances 1 } + +-- units of conformance + +isdnMibBasicRateGroup OBJECT-GROUP + OBJECTS { + isdnBasicRateIfType, + isdnBasicRateLineTopology, + isdnBasicRateIfMode, + isdnBasicRateSignalMode + } + STATUS current + DESCRIPTION + "A collection of objects required for ISDN Basic Rate + physical interface configuration and statistics." + ::= { isdnMibGroups 1 } + +isdnMibBearerGroup OBJECT-GROUP + OBJECTS { + isdnBearerChannelType, + isdnBearerOperStatus, + isdnBearerChannelNumber, + isdnBearerPeerAddress, + isdnBearerPeerSubAddress, + isdnBearerCallOrigin, + isdnBearerInfoType, + isdnBearerMultirate, + isdnBearerCallSetupTime, + isdnBearerCallConnectTime, + isdnBearerChargedUnits + } + STATUS current + DESCRIPTION + "A collection of objects required for ISDN Bearer channel + control and statistics." + ::= { isdnMibGroups 2 } + +isdnMibSignalingGroup OBJECT-GROUP + OBJECTS { + isdnSignalingGetIndex, + isdnSignalingIfIndex, + isdnSignalingProtocol, + isdnSignalingCallingAddress, + isdnSignalingSubAddress, + isdnSignalingBchannelCount, + isdnSignalingInfoTrapEnable, + isdnSignalingStatus, + isdnSigStatsInCalls, + isdnSigStatsInConnected, + isdnSigStatsOutCalls, + isdnSigStatsOutConnected, + isdnSigStatsChargedUnits, + isdnLapdPrimaryChannel, + isdnLapdOperStatus, + isdnLapdPeerSabme, + isdnLapdRecvdFrmr + } + STATUS current + DESCRIPTION + "A collection of objects required for ISDN D channel + configuration and statistics." + ::= { isdnMibGroups 3 } + +isdnMibEndpointGroup OBJECT-GROUP + OBJECTS { + isdnEndpointGetIndex, + isdnEndpointIfIndex, + isdnEndpointIfType, + isdnEndpointTeiType, + isdnEndpointTeiValue, + isdnEndpointSpid, + isdnEndpointStatus + } + STATUS current + DESCRIPTION + "A collection of objects describing Terminal Endpoints." + ::= { isdnMibGroups 4 } + +isdnMibDirectoryGroup OBJECT-GROUP + OBJECTS { + isdnDirectoryNumber, + isdnDirectorySigIndex, + isdnDirectoryStatus + } + STATUS current + DESCRIPTION + "A collection of objects describing directory numbers." + ::= { isdnMibGroups 5 } + +-- isdnMibNotificationsGroup NOTIFICATION-GROUP +-- NOTIFICATIONS { isdnMibCallInformation } +-- STATUS current +-- DESCRIPTION +-- "The notifications which a ISDN MIB entity is +-- required to implement." +-- ::= { isdnMibGroups 6 } + + +END |