diff options
Diffstat (limited to 'MIBS/enterasys/CTRON-CDP-MIB')
| -rw-r--r-- | MIBS/enterasys/CTRON-CDP-MIB | 468 |
1 files changed, 468 insertions, 0 deletions
diff --git a/MIBS/enterasys/CTRON-CDP-MIB b/MIBS/enterasys/CTRON-CDP-MIB new file mode 100644 index 0000000..58b2b07 --- /dev/null +++ b/MIBS/enterasys/CTRON-CDP-MIB @@ -0,0 +1,468 @@ +CTRON-CDP-MIB DEFINITIONS ::= BEGIN + +-- ctron-cdp-mib.txt +-- Revision: 1.00.04 +-- Part Number: +-- Date: August 28, 1999 + +-- Cabletron Systems reserves the right to make changes in +-- specification and other information contained in this document +-- without prior notice. The reader should consult Cabletron Systems +-- to determine whether any such changes have been made. +-- +-- In no event shall Cabletron Systems be liable for any incidental, +-- indirect, special, or consequential damages whatsoever (including +-- but not limited to lost profits) arising out of or related to this +-- document or the information contained in it, even if Cabletron +-- Systems has been advised of, known, or should have known, the +-- possibility of such damages. +-- +-- Cabletron grants vendors, end-users, and other interested parties +-- a non-exclusive license to use this Specification in connection +-- with the management of Cabletron products. +-- +-- Copyright September 1999 Cabletron Systems +-- + +IMPORTS + ctCDP + FROM CTRON-MIB-NAMES + ifIndex, InterfaceIndex + FROM IF-MIB + MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Counter32 + FROM SNMPv2-SMI + MODULE-COMPLIANCE, OBJECT-GROUP + FROM SNMPv2-CONF + MacAddress, TimeStamp, TEXTUAL-CONVENTION, DisplayString + FROM SNMPv2-TC + TimeFilter + FROM RMON2-MIB; + +ctronCdpMIB MODULE-IDENTITY + LAST-UPDATED + "199908280000Z" -- August 28, 1999 + + ORGANIZATION + "Cabletron Systems, Inc." + + CONTACT-INFO + "Cabletron Systems, Inc. + 35 Industrial Way, P.O. Box 5005 + Rochester, NH 03867-0505 + (603) 332-9400 + support@ctron.com + http://www.ctron.com" + + DESCRIPTION + "This module defines a schema that maintains per port + neighbor information for the express purpose + of helping a managment application map + Layaer 2 topology." + ::= { ctCDP 3 } + + + CTCDPCapability ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "The current capabilities of the neighbor device on a per +port basis. " + SYNTAX INTEGER { + igmp(1), -- IGMP enabled on the port over which device sent the packet + rip(2), -- Device performs routing using RIP + bgp(3), -- Device performs routing using BGP + ospf(4), -- Device performs routing using OSPF + dvmrp(5), -- Device performs DVMRP routing + ieee8021q(6), -- Device supports 802.1Q packet format on the port over + -- which it sent bthe CDP packet + gvrp(7), -- Device supports GARP VLAN Registration Protocol + gmrp(8), -- Device supports Multicast Registration Protocol + igmpSnoop(9), -- Device is a bridge and supports IGMP protocol snooping + dhcpServer(10), -- Device runs DHCP Server + dnsServer(11), -- Device runs DNS Server + activeDirectory(12) -- Device runs Active Directory Server + } + +ctCDPNeighbor OBJECT IDENTIFIER ::= { ctCDP 1 } +ctCDPStatus OBJECT IDENTIFIER ::= { ctCDP 2 } +ctCDPStats OBJECT IDENTIFIER ::= { ctCDP 4 } + +ctCDPNeighborLastChange OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at the time the cdpNeighborTable + was subject to these events: row insertion, row deletion" + ::= { ctCDPNeighbor 1 } + +ctCDPNeighborLastDelete OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime the last time an entry in the + ctCDPNeighborTable was deleted. This should be polled + at an interval no greater than one second. + When it changes, the whole table should be + reread by management with a timeMark of 0 to rebuild + connectivity map." + ::= { ctCDPNeighbor 2 } + + +ctCDPNeighborTable OBJECT-TYPE + SYNTAX SEQUENCE OF CtCDPNeighborEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The CommonNeighborTable holds all known neighbors speaking + cdp protocols." + ::= { ctCDPNeighbor 3 } + +ctCDPNeighborEntry OBJECT-TYPE + SYNTAX CtCDPNeighborEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry containing objects pertaining to + neighbor devices speaking CDP protocols." + INDEX { ctCDPNeighborTimeMark, ifIndex, ctCDPNeighborMAC } + ::= { ctCDPNeighborTable 1 } + +CtCDPNeighborEntry ::= +SEQUENCE { + ctCDPNeighborTimeMark TimeFilter, + ctCDPNeighborMAC MacAddress, + ctCDPNeighborIP IpAddress, + ctCDPNeighborPort InterfaceIndex, + ctCDPNeighborType INTEGER, + ctCDPNeighborChassisMAC MacAddress, + ctCDPNeighborChassisIP IpAddress, + ctCDPNeighborDescription DisplayString, + ctCDPNeighborPortName DisplayString, + ctCDPNeighborCapability CTCDPCapability + } + +ctCDPNeighborTimeMark OBJECT-TYPE + SYNTAX TimeFilter + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A TimeFilter for this entry as defined in RFC 2021." + ::= { ctCDPNeighborEntry 1 } + +ctCDPNeighborMAC OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The interface mac address of neighboring entity." + ::= { ctCDPNeighborEntry 2 } + +ctCDPNeighborIP OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP address of SNMP agent on neighboring entity from which + corresponding data for this port may be obtained. In the case + of unnumbered IP Interfaces, this may not be the same as the + port." + ::= { ctCDPNeighborEntry 3 } + +ctCDPNeighborPort OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ifIndex of the remote port. Note, there may not be an IP + Interface associated with this port." + ::= { ctCDPNeighborEntry 4 } + +ctCDPNeighborType OBJECT-TYPE + SYNTAX INTEGER { + secureFastSwitch(1), + dot1qSwitch(2), + router(3), + dot1dBridge(4), + vlanManager(5), + dnsServer(6), + dhcpServer(7), + dnsDhcpServer(8) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The type of entity. This value is used to determine the + general type of the object or service connected to a given port. + In general, it is better to use system group sysServices to + obtain an object's functionality." + ::= { ctCDPNeighborEntry 5 } + +ctCDPNeighborChassisMAC OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The MAC Address of the chassis in architectures + where many manageable elements exist within a + given chassis. If no containing chassis exists, + exists, this value must be set to 000000:000000" + ::= { ctCDPNeighborEntry 6 } + +ctCDPNeighborChassisIP OBJECT-TYPE + SYNTAX IpAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP address of the chassis itself. If no containing chassis + exists, this value must be set to 0.0.0.0" + ::= { ctCDPNeighborEntry 7 } + +ctCDPNeighborDescription OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A textual description of the neighbor. It + should contain operator diagnostic information + similar to sysDescr: system type, firmware version..." + ::= { ctCDPNeighborEntry 8 } + +ctCDPNeighborPortName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of object ifName of the neighbor's port." + ::= { ctCDPNeighborEntry 9 } + +ctCDPNeighborCapability OBJECT-TYPE + SYNTAX CTCDPCapability + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current capabilities of the neighbor port." + ::= { ctCDPNeighborEntry 10 } + +-- +-- CDPConfiguration Section +-- + +ctCDPGlobalStatus OBJECT-TYPE + SYNTAX INTEGER { + enable(1), + disable(2), + autoEnable(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The state of CDP for this entire managed entity. autoEnable(3) + should the default mode for new implementations. In autoEnable + mode, the device listens for CDP messages and upon receipt, begins + sending CDP messages of the same version and type as received." + ::= { ctCDPStatus 1 } + +ctCDPAuthenticationCode OBJECT-TYPE + SYNTAX OCTET STRING (SIZE( 0..255)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The authentication code may be set to create individual CDP + domains. CDP packets that arrive on a port must contain this + string. This authentication code is global for the entire + managed entity. The default for this string is 16 nulls." + ::= { ctCDPStatus 2 } + +ctCDPPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF CtCDPPortTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table shows enable/disable CDP status for each port." + ::= { ctCDPStatus 3 } + +ctCDPPortTableEntry OBJECT-TYPE + SYNTAX CtCDPPortTableEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Each entry is indicative of a particuliar port in the system." + INDEX { ctCDPPort } + ::= { ctCDPPortTable 1 } + +CtCDPPortTableEntry ::= + SEQUENCE { + ctCDPPort + InterfaceIndex, + ctCDPPortStatus + INTEGER + } + +ctCDPPort OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The ifIndex for a physical port. ifConnectorPresent is true(1) + defines a physical port on which cdp pdus will be emitted." + ::= { ctCDPPortTableEntry 1 } + +ctCDPPortStatus OBJECT-TYPE + SYNTAX INTEGER { + enabled(1), -- CDP is enabled always on the port + disabled(2), -- CDP is disabled always on the port + autoEnable(3) -- CDP is automatically enabled on the port + -- when device receives CDP packet on that port + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The current state administrative of cdp on a physical port. + The ability to enable and disable the sending of CDP pdu's + on a per port basis is controlled here." + ::= { ctCDPPortTableEntry 2 } + + +ctCDPTransmitFrequency OBJECT-TYPE + SYNTAX INTEGER (5..900) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The rate in seconds at which CDP pdu's are sent on all enabled ports." + ::= { ctCDPStatus 4 } + +ctCDPHoldTime OBJECT-TYPE + SYNTAX INTEGER (15..600) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The maximum amount of time in seconds to wait before aging out + an entry in the ctCDPNeighborTable. The agent may choose to change + this value based on the hold time it receives from other devices + so as to have a stable neighbor table which ages out entries + in accordance with the transmit frequency." + ::= { ctCDPStatus 5 } + +ctCDPVersion OBJECT-TYPE + SYNTAX OCTET STRING (SIZE(2)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The CDP version supported by this device as a bit string. + For example, given support for two versions of cdp: 3 and 4 + the bit representation in big endian form would be: 00001100." + ::= { ctCDPStatus 6 } + +-- +-- CDP statistics +-- + +ctCDPInPackets OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of CDP packets received by the device over all + the ports." + ::= { ctCDPStats 1 } + +ctCDPOutPackets OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of CDP packets successfully transmitted by the + device over all the ports." + ::= { ctCDPStats 2 } + +ctCDPInvalidVersionPackets OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of CDP packets received with version not + supported by the device." + ::= { ctCDPStats 3 } + +ctCDPParseErrorPackets OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of CDP packets received and could not be parsed + successfully by the device." + ::= { ctCDPStats 4 } + +ctCDPTransmitErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of errors occured by the device while trying + to transmit CDP packets." + ::= { ctCDPStats 5 } + +ctCDPMemoryErrors OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Count of memory errors occured in the device while + either trying to process the CDP packet or adding the + neighbor entry or while trying to send a CDP packet." + ::= { ctCDPStats 6 } + + +-- +-- Compliance Statements +-- + +ctCDPConformance OBJECT IDENTIFIER ::= { ctronCdpMIB 11 } +ctCDPCompliances OBJECT IDENTIFIER ::= { ctCDPConformance 1 } +ctCDPGroups OBJECT IDENTIFIER ::= { ctCDPConformance 2 } + +ctCDPComplianceV10 MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statement for the ctronCdpMIB." + MODULE -- this module + MANDATORY-GROUPS { ctCdpGroupV10 } + ::= { ctCDPCompliances 1 } + +ctCdpGroupV10 OBJECT-GROUP + OBJECTS { + ctCDPNeighborLastChange, + ctCDPNeighborLastDelete, + ctCDPNeighborTimeMark, + ctCDPNeighborMAC, + ctCDPNeighborIP, + ctCDPNeighborPort, + ctCDPNeighborType, + ctCDPNeighborChassisMAC, + ctCDPNeighborChassisIP, + ctCDPGlobalStatus, + ctCDPAuthenticationCode, + ctCDPPort, + ctCDPPortStatus, + ctCDPNeighborDescription, + ctCDPNeighborPortName, + ctCDPNeighborCapability, + ctCDPTransmitFrequency, + ctCDPHoldTime, + ctCDPVersion, + + ctCDPInPackets, + ctCDPOutPackets, + ctCDPInvalidVersionPackets, + ctCDPParseErrorPackets, + ctCDPTransmitErrors, + ctCDPMemoryErrors + } + STATUS current + DESCRIPTION + "The set of managed objects that make up version 2 of the + CTRON-CDP-MIB." + ::= { ctCDPGroups 1 } + +END |