path: root/MIBS/enterasys/CTRON-IF-REMAP-2-MIB

CTRON-IF-REMAP-2-MIB DEFINITIONS ::= BEGIN

--  ctron-if-remap-2-mib.txt
--  Revision: 02.00.02
--  Part Number: 
--  Date: September 15, 1998

--  Cabletron Systems, Inc.
--  35 Industrial Way, P.O. Box 5005
--  Rochester, NH 03867-0505
--  (603) 332-9400
--  support@ctron.com

--  This module provides authoritative definitions for Cabletron's
--  enterprise-specific Interface Remap MIB.
--
--  This module will be extended, as required.
--

--  Cabletron Systems reserves the right to make changes in 
--  specification and other information contained in this document 
--  without prior notice.  The reader should consult Cabletron Systems
--  to determine whether any such changes have been made.
--
--  In no event shall Cabletron Systems be liable for any incidental, 
--  indirect, special, or consequential damages whatsoever (including 
--  but not limited to lost profits) arising out of or related to this
--  document or the information contained in it, even if Cabletron
--  Systems has been advised of, known, or should have known, the 
--  possibility of such damages.
--
--  Cabletron grants vendors, end-users, and other interested parties
--  a non-exclusive license to use this Specification in connection
--  with the management of Cabletron products.

--  Copyright August 98 Cabletron Systems

        IMPORTS
            OBJECT-TYPE
                FROM RFC-1212
            ctIFRemap2
                FROM CTRON-MIB-NAMES;


        ctIFRemap2Config OBJECT IDENTIFIER ::= { ctIFRemap2 1 }


-- The ctIFRemap2Config group is used to control ifremapping.  Ifremapping
-- provides the ability to map one port or one vlan directly to another port.
-- This control is defined by creating a row in the ctIFRemap2Table
-- specifying source slot, source port, destination slot, and destination
-- port with ctIFRemap2Status set to a value of enable(1) or by creating
-- a row in the ctIFRemap2VlanTable specifying source slot, source vlan, 
-- destination slot, destination port with ctIFRemap2VlanStatus set to a
-- value of enable(1).
-- 
-- When a source port is remapped to a destination port, the destination
-- port will transmit out all packets received or transmitted on the
-- source port. Counters on the destination port will increment for all
-- packets transmitted be it by normal packet forwarding or due to 
-- ifremap.
--
-- When a source vlan is remapped to a destination port, the destination
-- port will transmit out all packets received on the source vlan. Counters 
-- on the destination port will increment for all packets transmitted be it
-- by normal packet forwarding or due to ifremap.
-- 
-- All tables in this MIB contain a slot instance.  In the case of a
-- stand-alone device the slot will always be 1.
--
-- Any mention of a vlan in this text refers to a Virtual Local Area Network
-- that is compliant to IEEE Draft P802.1Q/D11.


--
-- The IFRemap Table
--

ctIFRemap2Table  OBJECT-TYPE
    SYNTAX  SEQUENCE OF CtIFRemap2Entry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "This table provides the ability to remap all frames from one
            port onto another port.  A port is defined by 
ctIFRemap2PortIndex
            from the ctIFRemap2PortTable below.  Only ports listed in the
            ctIFRemap2PortTable are available for remapping.

            A given source port may only be mapped to only one destination 
            port.  Once a port is reserved as part of a ctIFRemap2Table  entry,
            it may not be used in any other ctIFRemap2Table entries (ie. If 
            remapping port 1 to port 3, then neither port 1 or port 3 may be
            used as a ctIFRemap2SourcePort or ctIFRemap2DestPort in another
            ctIFRemap2Table entry).

            Each row that exists in this table defines such a relationship.
            By disabling a row in this table the remapping relationship no 
            longer exists.

            Each entry will be referenced by slot.  In the case of a
            stand-alone device the slot will always be 1.

            If a given relationship cannot be created the set will fail
            with a BAD-VALUE error."
    ::= { ctIFRemap2Config 1 }


ctIFRemap2Entry  OBJECT-TYPE
    SYNTAX  CtIFRemap2Entry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "Describes a particular ifremap entry."
    INDEX { ctIFRemap2SourceSlot, ctIFRemap2SourcePort,
            ctIFRemap2DestSlot, ctIFRemap2DestPort }
    ::= { ctIFRemap2Table 1 }


CtIFRemap2Entry ::=
    SEQUENCE {
        ctIFRemap2SourceSlot
            INTEGER,
        ctIFRemap2SourcePort
            INTEGER,
        ctIFRemap2DestSlot
            INTEGER,
        ctIFRemap2DestPort
            INTEGER,
        ctIFRemap2Status
            INTEGER,
        ctIFRemap2PhysicalErrors
            INTEGER,
        ctIFRemap2EgressType
            INTEGER
    }


ctIFRemap2SourceSlot OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The slot combined with the ctIFRemap2SourcePort which will
            have all packets redirected to the destination port as defined
            by ctIFRemap2DestSlot and ctIFRemap2DestPort."
    ::= { ctIFRemap2Entry 1 }


ctIFRemap2SourcePort OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The port combined with the ctIFRemap2SourceSlot which will
            have all packets redirected to the destination port as defined
            by ctIFRemap2DestSlot and ctIFRemap2DestPort."
    ::= { ctIFRemap2Entry 2 }


ctIFRemap2DestSlot OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The slot combined with the ctIFRemap2DestPort which will
            see all packets redirected from ctIFRemap2SourceSlot and
            ctIFRemap2SourcePort."
    ::= { ctIFRemap2Entry 3 }


ctIFRemap2DestPort OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The port combined with the ctIFRemap2DestSlot which will
            see all packets redirected from ctIFRemap2SourceSlot and
            ctIFRemap2SourcePort."
    ::= { ctIFRemap2Entry 4 }


ctIFRemap2Status OBJECT-TYPE
    SYNTAX  INTEGER {
                enable(1),
                disable(2)
            }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Defines the status of the ifremap entry.  Setting
            ctIFRemap2Status to a value of enable(1) has the effect of
            creating an entry in the table when it does not already exist.
            Setting ctIFRemap2Status to a value of disable(2) disables the
            entry and deletes the row from the table.  Therefore this
            table only contains entries that are active."
    DEFVAL { enable }
    ::= { ctIFRemap2Entry 5 }


ctIFRemap2PhysicalErrors OBJECT-TYPE
    SYNTAX INTEGER {
               enable(1),
               disable(2),
               unsupported(3)
           }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
            "Enable or disable remapping of physical errors.  This object
            controls whether or not frames with physical errors should be
            remapped out the destination port for this entry.  By default,
            this will be enabled when an entry is created.
            
            NOTE: This action is always superseded by the value of
            ctIFRemap2PhysErrsCapable for either the source or destination
            port specified in this remap entry.  If a port is not
            physically capable of transmitting or receiving error frames,
            then this object will return unsupported(3) and the value
            cannot be changed."
    DEFVAL { enable }
    ::= { ctIFRemap2Entry 6 }


ctIFRemap2EgressType OBJECT-TYPE
    SYNTAX INTEGER {
               normal(1),
               alwaysTagged(2),
               alwaysUntagged(3)
           }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
            "Defines how each packet will be tagged when sent out the 
             ctIFRemap2DestPort.  Setting ctIFRemap2EgressType to normal(1)
             will set packets to be sent out as they are seen by 
             ctIFRemap2SourcePort.  Setting ctIFRemap2EgressType to 
             alwaysTagged(2) will set packets to always be sent out 
             ctIFRemap2DestSlot and ctIFRemap2DestPort with a tag. Setting 
             ctIFRemap2EgressType to alwaysUntagged(3) will set packets to always 
             be sent out ctIFRemap2DestSlot and ctIFRemap2DestPort without a tag.
             If the module is not configured to support packet tagging (i.e. 802.1d 
             bridge mode) then setting this object to alwaysTagged(2) or 
             alwaysUntagged(3) will return a BAD-VALUE error."
    DEFVAL { normal }
    ::= { ctIFRemap2Entry 7 }

--
-- The IFRemap Port Table
--

ctIFRemap2PortTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF CtIFRemap2PortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "This table holds all valid ports that are remappable or
            able to accept a remapped packet."
    ::= { ctIFRemap2Config 2 }


ctIFRemap2PortEntry  OBJECT-TYPE
    SYNTAX  CtIFRemap2PortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "Describes a particular supported remappable port."
    INDEX { ctIFRemap2PortSlot, ctIFRemap2PortIndex }
    ::= { ctIFRemap2PortTable 1 }


CtIFRemap2PortEntry ::=
    SEQUENCE {
        ctIFRemap2PortSlot
                INTEGER,
        ctIFRemap2PortIndex
                INTEGER,
        ctIFRemap2PortReference
                OBJECT IDENTIFIER,
        ctIFRemap2PhysErrsCapable
                INTEGER
        }


ctIFRemap2PortSlot OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Defines the slot in which the remap capable module resides. 
            In the case of a stand-alone device the slot will always be 1."
    ::= { ctIFRemap2PortEntry 1 }


ctIFRemap2PortIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Defines an port that is remappable or is able to accept a
            remapped packet.  Ideally indices will start with 1 and will
            be numbered continuously through the number of available remap
            ports.  However, this need not necessarily be the case.
            Indices may be sparse and begin with any number if desired
            for a particular implementation."
    ::= { ctIFRemap2PortEntry 2  }


ctIFRemap2PortReference OBJECT-TYPE
    SYNTAX  OBJECT IDENTIFIER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This object returns an OID referencing an object which
             uniquely corresponds to this remap port.  The only criteria
             is that this OID is a leaf, and that it exists and is
             accessible.  For example, if remap functionality is running
             on an 802.1d compliant bridge, remap port #1 could reference
             dot1dBasePort.1. Alternatively you could reference a mib2
             interface like ifIndex.1 or a Cabletron Secure Fast port.
             Mixing these types (some refer to bridge ports, others refer
             to SFS ports) is not advised, but not prohibited"
    ::= { ctIFRemap2PortEntry 3  }


ctIFRemap2PhysErrsCapable OBJECT-TYPE
    SYNTAX INTEGER {
               supported(1),
               unsupported(2)
           }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "Indicate whether the port is incapable of remapping physical
            errors.  If the capability is supported, this object will
            return supported(1).  If the capability is unsupported, this
            object will return unsupported(2)."
    ::= { ctIFRemap2PortEntry 4 }


--
-- The IFRemap Slot Table
--

ctIFRemap2SlotTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF CtIFRemap2SlotEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "This table contains all information pertaining to the
            abilities or limitations of a particular remap capable
            module."
    ::= { ctIFRemap2Config 3 }


ctIFRemap2SlotEntry OBJECT-TYPE
    SYNTAX  CtIFRemap2SlotEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "Describes a particular entry in the ctIFRemap2SlotTable.
            Each entry is indexed by the physical slot in which the
            module resides."
    INDEX { ctIFRemap2SlotIndex }
    ::= { ctIFRemap2SlotTable 1 }


CtIFRemap2SlotEntry ::=
    SEQUENCE {
        ctIFRemap2SlotIndex
            INTEGER,
        ctIFRemap2SlotMaxRemaps
            INTEGER,
        ctIFRemap2SlotMaxRemoteDests
            INTEGER
    }


ctIFRemap2SlotIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Defines the slot in which the remap capable module resides. 
In
            the case of a stand-alone device the slot will always be 1."
    ::= { ctIFRemap2SlotEntry 1 }


ctIFRemap2SlotMaxRemaps OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The maximum number of entries allowed to be sourced from the
            module in this slot in the ctIFRemap2Table."
    ::= { ctIFRemap2SlotEntry 2 }

ctIFRemap2SlotMaxRemoteDests OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The maximum number of remote destination ports per remote
            module.  For example, a value of 3 means that I can have no
            more than 3 remap destination ports between this module, and
            any other given module in the same chassis simultaneously. I
            can have multiple source ports remapped to each of the three
            remote destination ports.  I can also remap to up to three
            remote destination ports on each of the other modules in the
            chassis simultaneously."
    ::= { ctIFRemap2SlotEntry 3 }


--
-- The IFRemap Vlan Table
--
-- The ctIFRemap2VlanTable may only be implemented on a Cabletron Bridge 
-- which supports the use of IEEE Draft P802.1Q/D11 compliant vlans.
-- 
-- The implementation of this table is OPTIONAL

ctIFRemap2VlanTable  OBJECT-TYPE
    SYNTAX  SEQUENCE OF CtIFRemap2VlanEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "This table provides the ability to remap all frames from any
            port on a particular vlan to a specific destination port.  
            Each row that exists in this table defines such a relationship.
            By disabling a row in this table the remapping relationship no
            longer exists.

            Multiple vlans may be mapped to a given destination port 
            (ie. vlan 11 and vlan 35 may both remap to port 10).

            A port is defined by ctIFRemap2PortIndex in the ctIFRemap2PortTable,
            above.  Only ports listed in the ctIFRemap2PortTable are available
            for remapping.  A  vlan is defined by ctVlanVID in the
            ctVlanConfigTable. Only vlans listed in the ctVlanConfigTable are
            available for remapping.

            Each entry will be referenced by slot.  In the case of a
            stand-alone device the slot will always be 1.

            If a given relationship cannot be created the set will fail
            with a BAD-VALUE error."
    REFERENCE
            "ctvlan-ext-mib .4.4.1.1"
    ::= { ctIFRemap2Config 4 }


ctIFRemap2VlanEntry  OBJECT-TYPE
    SYNTAX  CtIFRemap2VlanEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "Describes a particular ifremap Vlan entry."
    INDEX { ctIFRemap2VlanSourceSlot, ctIFRemap2VlanSourceVlan,
            ctIFRemap2VlanDestSlot, ctIFRemap2VlanDestPort }
    ::= { ctIFRemap2VlanTable 1 }

CtIFRemap2VlanEntry ::=
    SEQUENCE {
        ctIFRemap2VlanSourceSlot
            INTEGER,
        ctIFRemap2VlanSourceVlan
            INTEGER,
        ctIFRemap2VlanDestSlot
            INTEGER,
        ctIFRemap2VlanDestPort
            INTEGER,
        ctIFRemap2VlanStatus
            INTEGER,
        ctIFRemap2VlanEgressType
            INTEGER
    }

ctIFRemap2VlanSourceSlot OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The slot combined with the ctIFRemap2VlanSourceVlan which will
            have all packets redirected to the destination port as defined
            by ctIFRemap2VlanDestSlot and ctIFRemap2VlanDestPort."
    ::= { ctIFRemap2VlanEntry 1 }


ctIFRemap2VlanSourceVlan OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The vlan combined with the ctIFRemap2VlanSourceSlot which will
            have all packets redirected to the destination port as defined
            by ctIFRemap2VlanDestSlot and ctIFRemap2VlanDestPort."
    ::= { ctIFRemap2VlanEntry 2 }


ctIFRemap2VlanDestSlot OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The slot combined with the ctIFRemap2VlanDestPort which will
            see all packets redirected from ctIFRemap2VlanSourceSlot and
            ctIFRemap2VlanSourceVlan."
    ::= { ctIFRemap2VlanEntry 3 }


ctIFRemap2VlanDestPort OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The port combined with the ctIFRemap2VlanDestSlot which will
            see all packets redirected from ctIFRemap2VlanSourceSlot and
            ctIFRemap2VlanSourceVlan."
    ::= { ctIFRemap2VlanEntry 4 }


ctIFRemap2VlanStatus OBJECT-TYPE
    SYNTAX  INTEGER {
                enable(1),
                disable(2)
            }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Defines the status of the ifremap vlan entry.  Setting
            ctIFRemap2VlanStatus to a value of enable(1) has the effect of
            creating an entry in the table when it does not already exist.
            Setting ctIFRemap2VlanStatus to a value of disable(2) disables the
            entry and deletes the row from the table.  Therefore this
            table only contains entries that are active.
   
            If ctIFRemap2VlanSourceVlan is already being used by another
            ctIfRemap2Vlan entry or ctifRemap2 Entry then a set to 
            ctIFRemap2VlanStatus of value enable(1) will return with a
            BAD-VALUE error."
    DEFVAL { enable }
    ::= { ctIFRemap2VlanEntry 5 }
 

ctIFRemap2VlanEgressType OBJECT-TYPE
    SYNTAX INTEGER {
               received(1),
               alwaysTagged(2),
               alwaysUntagged(3)
           }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
            "Defines how each packet will be tagged when sent out the 
             ctIFRemap2VlanDestPort.  Setting ctIFRemap2VlanEgressType to 
             received(1) will set packets to be sent out ctIFRemap2VlanDestSlot
             and ctIFRemap2VlanDestPort exactly as they are received by 
             ctIFRemap2VlanSourceVlan. Setting ctIFRemap2VlanEgressType to 
             alwaysTagged(2) will set packets to be sent out 
             ctIFRemap2VlanDestSlot and ctIFRemap2VlanDestPort with the 
             vlan tag associated with ctIFRemap2VlanSourceVlan.  If this port
             does not have a vlan tag associated with it then all packets will
             be remapped without a tag.  Setting ctIFRemap2VlanEgressType to
             alwaysUntagged(3) will set packets to be sent out 
             ctIFRemap2VlanDestSlot and ctIFRemap2VlanDestPort without any
             tag reguardless of ctIFRemap2VlanSourceVlan's tagging status."
    DEFVAL { received }
    ::= { ctIFRemap2VlanEntry 6 }

END