path: root/MIBS/infinera/LUM-IFBASIC-MIB

LUM-IFBASIC-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Counter64
        FROM SNMPv2-SMI
    OBJECT-GROUP, MODULE-COMPLIANCE
        FROM SNMPv2-CONF
    DateAndTime, DisplayString
        FROM SNMPv2-TC
    lumModules, lumIfBasicMIB
        FROM LUM-REG
    SignalFormat, AdminStatusWithNA, OperStatusWithNA,
    Unsigned32WithNA, SignalStatusWithNA, EnabledDisabledWithNA,
    Time7200min, Time7200minNo0, Layer, AutoAlarmStatus, ResetWithNA, FaultStatusWithNA,
    MgmtNameString, DisplayStringWithNA, CommandString, TribPortIdType, OpticalLayerMappingType,
    PhysicalLayerMappingType, SignalDirection, InterfaceStatus, ConnectorType, InterfaceType, TruthValueWithNA
        FROM LUM-TC;

lumIfBasicMIBModule MODULE-IDENTITY
    LAST-UPDATED
        "201906280000Z" -- June 28th 2019
    ORGANIZATION
        "Infinera Corporation"
    CONTACT-INFO
        "techsupport@infinera.com"
    DESCRIPTION
        "The MIB module for management of basic port objects.

        The tables contained in this MIB are:

        (1) The General group contains some general attributes as time stamps
            and tables sizes.

        (2) The If group contains information about the name of the port that
            is used in GUI.

        (2) The Admin group contains information and configuration for all
            interfaces available for If Basic Admin objects.

        (3) The Signal group contains information and configuration for all
            interfaces available for If Basic Signal objects.

"
    REVISION
        "201906280000Z" -- June 28th 2019
    DESCRIPTION
        "Changes made for release r33.0:
         - Added oa1x21dBmVgEC board
         - Added oa2x21dBmVgEC board"
    REVISION
        "201812310000Z" -- December 31st 2018
    DESCRIPTION
        "Changes made for release r32.0:
         - Added ifBasicAdminNotAvailableForUse"
    REVISION
        "201806290000Z" -- June 29th 2018
    DESCRIPTION
        "Changes made for release r31.0:
         - Added mxp200gotn board
         - Added ifBasicSignalConnectorType
         - Added ifBasicAdminIfNo
         - Added ifBasicSignalLowOrderTribPortId
         - Added ifBasicAdminIfType"
    REVISION
        "201706150000Z" -- June 15th 2017
    DESCRIPTION
        "Changes made for release r29.0:
         - Changed ORGANIZATION and CONTACT-INFO"
    REVISION
        "201611300000Z" -- November 30th 2016
    DESCRIPTION
        "Changes made for release r28:
        - Added interface status attribute.
        - Added Terminal and facility loopback (and corresponding attributes)."
    REVISION
        "201611040000Z" -- November 4th 2016
    DESCRIPTION
        "Changes made for patch release r27.0.3:
        - Enabled Read-Write to Loopback and TTI attributes via SNMP."
    REVISION
        "201601310000Z" -- January 31th 2016
    DESCRIPTION
        "Changes made for release r26.1:
        - Added upId in If group."
    REVISION
        "201512220000Z" -- December 22nd 2015
    DESCRIPTION
        "Changes made for release r27:
        - Added fhau1 board
        - Added fha1u1 board"
    REVISION
        "201510300000Z" -- October 30th 2015
    DESCRIPTION
        "Added tpmrHL16GUni board:
        -Added SignalSpeed."
    REVISION
        "201409300000Z" -- September 30th 2014
    DESCRIPTION
        "Changes made for release r23.1:
        - Added mxp100gotn board."
    REVISION
        "201405160000Z" -- May 16th 2014
    DESCRIPTION
        "Changes made for release r23:
        - Added Optical layer mapping configuration mismatch object.
        - Changed board name from tp10gotn to tphex10gotn.
        - Added tpmrHL16G board"
    REVISION
        "201311150000Z" -- November 15th 2013
    DESCRIPTION
        "Changes made for release r22:
        - Added tp10gotn, tp100gotn board.
        - Added lane format"
    REVISION
        "201211200000Z" -- November 20th 2012
    DESCRIPTION
        "The initial revision of this module."
    ::= { lumModules 46 }


-- ----------------------------------------------------
-- Compliance area, containing groups and compliance
-- specifications.
-- ----------------------------------------------------

lumIfBasicConfs OBJECT IDENTIFIER ::= { lumIfBasicMIB 1 }
lumIfBasicGroups OBJECT IDENTIFIER ::= { lumIfBasicConfs 1 }
lumIfBasicCompl OBJECT IDENTIFIER ::= { lumIfBasicConfs 2 }


-- ----------------------------------------------------
-- Root for objects in the IFBASIC MIB
-- ----------------------------------------------------

lumIfBasicMIBObjects OBJECT IDENTIFIER ::= { lumIfBasicMIB 2 }


-- ----------------------------------------------------
-- This MIB contains the following groups:
-- ----------------------------------------------------

ifBasicGeneral OBJECT IDENTIFIER ::= { lumIfBasicMIBObjects 1 }
ifBasicIfList OBJECT IDENTIFIER ::= {lumIfBasicMIBObjects 2}
ifBasicAdminList OBJECT IDENTIFIER ::= { lumIfBasicMIBObjects 3 }
ifBasicSignalList OBJECT IDENTIFIER ::= { lumIfBasicMIBObjects 4 }

-- ----------------------------------------------------
-- General group
-- ----------------------------------------------------

ifBasicGeneralConfigLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the configuration of the MIB was
        last changed.

"
    ::= { ifBasicGeneral 1 }

ifBasicGeneralStateLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the state of the MIB was last
        changed.

"
    ::= { ifBasicGeneral 2 }

ifBasicGeneralIfBasicIfTableSize OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Size of if table

"
    ::= { ifBasicGeneral 3 }

ifBasicGeneralIfBasicIfConfigLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the configuration of the
        table was last changed.
"
    ::= { ifBasicGeneral 4 }

ifBasicGeneralIfBasicIfStateLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the state and/or configuration of
        the table was last changed.

"
    ::= { ifBasicGeneral 5 }

ifBasicGeneralIfBasicAdminTableSize OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Size of admin table

"
    ::= { ifBasicGeneral 6 }

 ifBasicGeneralIfBasicAdminConfigLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the configuration of the table was
        last changed.

"
    ::= { ifBasicGeneral 7 }

ifBasicGeneralIfBasicAdminStateLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the state and/or configuration of
        the table was last changed.

"
    ::= { ifBasicGeneral 8 }

ifBasicGeneralIfBasicSignalTableSize OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Size of signal table

"
    ::= { ifBasicGeneral 9 }

ifBasicGeneralIfBasicSignalConfigLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the configuration of the table was
        last changed.

"
    ::= { ifBasicGeneral 10 }

ifBasicGeneralIfBasicSignalStateLastChangeTime OBJECT-TYPE
    SYNTAX      DateAndTime
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The time when the state and/or configuration of
        the table  was last changed.

"
    ::= { ifBasicGeneral 11 }

-- ----------------------------------------------------
-- If group
-- ----------------------------------------------------

ifBasicIfTable  OBJECT-TYPE
    SYNTAX      SEQUENCE OF IfBasicIfEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The if basic if interface list."

    ::= { ifBasicIfList 1 }

ifBasicIfEntry OBJECT-TYPE
    SYNTAX      IfBasicIfEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in the ifBasic if list.

"
    INDEX { ifBasicIfIndex }
    ::= { ifBasicIfTable 1 }

IfBasicIfEntry ::=
    SEQUENCE {
        ifBasicIfIndex                          Unsigned32,
        ifBasicIfName                           MgmtNameString,
        ifBasicIfTxSignalStatus                 SignalStatusWithNA,
        ifBasicIfRxSignalStatus                 SignalStatusWithNA,
        ifBasicIfUpId                           Unsigned32,
        ifBasicIfAid                            DisplayString,
        ifBasicIfPhysicalLocation               DisplayString }

ifBasicIfIndex  OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "An index assigned to each entry.

"
    ::= { ifBasicIfEntry 1 }

ifBasicIfName OBJECT-TYPE
    SYNTAX      MgmtNameString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The management name of the interface, for example
        'client:1:2:1-2', where the first number indicates
        subrack, the second slot number and the third/fourth
        are the physical port numbers.

"
    ::= { ifBasicIfEntry 2 }

ifBasicIfTxSignalStatus OBJECT-TYPE
    SYNTAX      SignalStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The state for outgoing (TX) signal
        of the interface.

        down - A major fault has occurred.

        degraded - The signal quality is impaired.

        up - The signal is OK.

"
    ::= { ifBasicIfEntry 3 }

ifBasicIfRxSignalStatus OBJECT-TYPE
    SYNTAX      SignalStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The state for incoming (RX) signal
        of the interface.

        down - A major fault has occurred.

        degraded - The signal quality is impaired.

        up - The signal is OK.

"
    ::= { ifBasicIfEntry 4 }

ifBasicIfUpId OBJECT-TYPE
    SYNTAX      Unsigned32   (0..2147483647)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Identity in the UP for the interface. The upId is used internally between CU and
         TU to define a certain interface in the TU.
"
    ::= { ifBasicIfEntry 5 }

ifBasicIfAid OBJECT-TYPE
    SYNTAX      DisplayString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The access identifier (AID) of the interface.
         The format is according to GR-833.

"
    ::= { ifBasicIfEntry 6 }


ifBasicIfPhysicalLocation OBJECT-TYPE
    SYNTAX      DisplayString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The physical location of the if.
         The format is according to GR-833.

"
    ::= { ifBasicIfEntry 7 }

-- ----------------------------------------------------
-- Admin group
-- ----------------------------------------------------

ifBasicAdminTable  OBJECT-TYPE
    SYNTAX      SEQUENCE OF IfBasicAdminEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The if basic admin interface list."

    ::= { ifBasicAdminList 1 }

ifBasicAdminEntry OBJECT-TYPE
    SYNTAX      IfBasicAdminEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in the ifBasic admin list.

"
    INDEX { ifBasicAdminIndex }
    ::= { ifBasicAdminTable 1 }

IfBasicAdminEntry ::=
    SEQUENCE {
        ifBasicAdminIndex                        Unsigned32,
        ifBasicAdminName                         MgmtNameString,
        ifBasicAdminDescr                        DisplayStringWithNA,
        ifBasicAdminSubrack                      Unsigned32WithNA,
        ifBasicAdminSlot                         Unsigned32WithNA,
        ifBasicAdminTxPort                       Unsigned32WithNA,
        ifBasicAdminRxPort                       Unsigned32WithNA,
        ifBasicAdminAdminStatus                  AdminStatusWithNA,
        ifBasicAdminOperStatus                   OperStatusWithNA,
        ifBasicAdminAutoAlarmEnableStatus        AutoAlarmStatus,
        ifBasicAdminAutoAlarmEnableReset         ResetWithNA,
        ifBasicAdminInterfaceStatus              InterfaceStatus,
        ifBasicAdminIfNo                         Unsigned32WithNA,
        ifBasicAdminIfType                       InterfaceType,
        ifBasicAdminNotAvailableForUse           TruthValueWithNA }

ifBasicAdminIndex OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "An index assigned to each entry.

"
    ::= { ifBasicAdminEntry 1 }

ifBasicAdminName OBJECT-TYPE
    SYNTAX      MgmtNameString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The management name of the interface, for example
        'admin:1:2:1-2', where the first number indicates
        subrack, the second slot number and the third/fourth
        are the physical port numbers.

"
    ::= { ifBasicAdminEntry 2 }

ifBasicAdminDescr OBJECT-TYPE
    SYNTAX      DisplayStringWithNA
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "User configurable label.


"
    DEFVAL { "" }
    ::= { ifBasicAdminEntry 3 }

ifBasicAdminSubrack OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The subrack of the physical port that this interface is bound to.

"
    ::= { ifBasicAdminEntry 4 }

ifBasicAdminSlot OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The slot of the physical port that this interface is bound to.

"
    ::= { ifBasicAdminEntry 5 }

ifBasicAdminTxPort OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The transmitting physical port that this interface is bound to.

"
    ::= { ifBasicAdminEntry 6 }

ifBasicAdminRxPort OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The receiving physical port that this interface is bound to.

"
    ::= { ifBasicAdminEntry 7 }

ifBasicAdminAdminStatus OBJECT-TYPE
    SYNTAX     AdminStatusWithNA
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The administrative state of the ifBasic interface.

        down - The interface is de-activated.

        service - The interface is activated but alarms
        are suppressed. Intended for use during service
        or re-configuration. When service is concluded
        adminStatus should be set to 'up' again. Note that
        there is no difference between 'up' and 'service',
        if no alarms can be raised from this object.

        up - The interface will be activated when
        available. Alarms are not suppressed.

"
    DEFVAL { up }
    ::= { ifBasicAdminEntry 8 }

ifBasicAdminOperStatus OBJECT-TYPE
    SYNTAX      OperStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The operational state for the interface.

        notPresent - The interface is not available.

        down - The interface is de-activated or there are
        faults preventing its transition to the 'up' state.

        up - The interface is active.

"
    DEFVAL { notPresent }
    ::= { ifBasicAdminEntry 9 }

ifBasicAdminAutoAlarmEnableStatus OBJECT-TYPE
    SYNTAX      AutoAlarmStatus
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The state of auto alarm enable for the interface.

        suppressTrxAndSignal  - Both signal alarms and trx alarms are suppressed
        suppressSignal        - Only signal alarms are suppressed
        suppressNone          - Neither trx nor signal alarms
                                are suppressed

"
    DEFVAL { suppressTrxAndSignal }
    ::= { ifBasicAdminEntry 10 }

ifBasicAdminAutoAlarmEnableReset OBJECT-TYPE
    SYNTAX      ResetWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "When the attribute is set to reset the auto-alarm enable function
        is re-initialised. Then the attribute is set to normal again
        automatically.

        reset - Re-initialises the auto-alarm enable function

        normal - The auto-alarm enable function is in normal state

"
    DEFVAL { normal }
    ::= { ifBasicAdminEntry 11 }

ifBasicAdminInterfaceStatus OBJECT-TYPE
    SYNTAX      InterfaceStatus
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The status of the traffic interface.

        outOfService    - No PM and no alarms.
        autoInService   - No PM and no alarms. Changes to 'inService' when OK.
        inService       - Reports PM and alarms.
        maintenance     - Maintenance mode.

"
    ::= { ifBasicAdminEntry 12 }

ifBasicAdminIfNo OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The physical interface number of the actual multi-connector port.

"
    DEFVAL { 2147483647 }
    ::= { ifBasicAdminEntry 13 }

ifBasicAdminIfType OBJECT-TYPE
    SYNTAX      InterfaceType
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "Type of interface (Individual or bundled).

"
    DEFVAL { notApplicable }
    ::= { ifBasicAdminEntry 14 }

ifBasicAdminNotAvailableForUse OBJECT-TYPE
    SYNTAX      TruthValueWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
         "Is the interface not available for use.
          The interface may be created in order to show some
          physical properties but may otherwise be unavailable
          for service depending on setup and available resources.

"
    DEFVAL { notApplicable }
    ::= { ifBasicAdminEntry 15 }

-- ----------------------------------------------------
-- Signal group
-- ----------------------------------------------------

ifBasicSignalTable  OBJECT-TYPE
    SYNTAX      SEQUENCE OF IfBasicSignalEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The if basic signal interface list."

    ::= { ifBasicSignalList 1 }

ifBasicSignalEntry OBJECT-TYPE
    SYNTAX      IfBasicSignalEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in the ifBasic signal list.

"
    INDEX { ifBasicSignalIndex }
    ::= { ifBasicSignalTable 1 }

IfBasicSignalEntry ::=
    SEQUENCE {
        ifBasicSignalIndex                           Unsigned32,
        ifBasicSignalName                            MgmtNameString,
        ifBasicSignalSignalStructure                 Counter64,
        ifBasicSignalSignalFormat                    SignalFormat,
        ifBasicSignalOpticalLayerMapping             OpticalLayerMappingType,
        ifBasicSignalFarEndLoopbackTerminatingLayer  Layer,
        ifBasicSignalFarEndLoopback                  EnabledDisabledWithNA,
        ifBasicSignalFarEndLoopbackTimeout           Time7200min,
        ifBasicSignalNearEndLoopbackTerminatingLayer Layer,
        ifBasicSignalNearEndLoopback                 EnabledDisabledWithNA,
        ifBasicSignalNearEndLoopbackTimeout          Time7200min,
        ifBasicSignalFarEndLoopbackEnabled           FaultStatusWithNA,
        ifBasicSignalNearEndLoopbackEnabled          FaultStatusWithNA,
        ifBasicSignalConfigurationMismatch           FaultStatusWithNA,  -- deprecated
        ifBasicSignalActualOpticalLayerMapping       OpticalLayerMappingType,
        ifBasicSignalSpeed                           Unsigned32WithNA,
        ifBasicSignalDirection                       SignalDirection,
        ifBasicSignalFormatConfigurable              INTEGER,
        ifBasicSignalFormatConfigurationSharedWithInterface Unsigned32WithNA,
        ifBasicSignalPhysicalLayerMapping            PhysicalLayerMappingType,
        ifBasicSignalFacilityLoopback                EnabledDisabledWithNA,
        ifBasicSignalFacilityLoopbackTimeout         Time7200minNo0,
        ifBasicSignalFacilityLoopbackEnabled         FaultStatusWithNA,
        ifBasicSignalTerminalLoopback                EnabledDisabledWithNA,
        ifBasicSignalTerminalLoopbackTimeout         Time7200minNo0,
        ifBasicSignalTerminalLoopbackEnabled         FaultStatusWithNA,
        ifBasicSignalConnectorType                   ConnectorType }

ifBasicSignalIndex OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "An index assigned to each entry.

"
    ::= { ifBasicSignalEntry 1 }

ifBasicSignalName OBJECT-TYPE
    SYNTAX      MgmtNameString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The management name of the interface, for example
        'signal:1:2:1-2', where the first number indicates
        subrack, the second slot number and the third/fourth
        are the physical port numbers.

"
    ::= { ifBasicSignalEntry 2 }

ifBasicSignalSignalStructure OBJECT-TYPE
    SYNTAX      Counter64
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The signal structure used. Bitfield 64 bit wide. For internal use.
        Bit 0 tells if mib ifBasicPhysicalTrx is loaded,
        bit 1 ifBasicOpticalTranssection, etc according to list below.
        Add new items last.
          ifPhysicalTrx
          ifOpticalTranssection
          ifOpticalChannel
          ifOpticalDigitalSignalRate
          ifEthPhysical
          ifEthMac
          ifOtnOdu
          ifOtnOtu
          ifOtnOpu
          ifOtnMonSm
          ifOtnMonPm
          ifOtnMonTcm
          ifOtnMonTrace
          ifSdhRs
          ifSdhMs
          ifSonetSection
          ifSonetLine
          ifPerfFec
          ifPerfAdmin
          ifPerfG826
          ifPerfL2Error
          ifPerfL1
          ifPerfL0
          ifOpticalFec
          ifFcPhysical
          ifOtnTp
          ifOpticalTransportLaneCarrier
          ifOpticalTransportLaneCarrierGroup
          ifPerfL2Stat
          ifIwdmRs
          ifIwdmMS
          ifAmplifierAmplifier
          ifAmplifierModule
          ifAmplifierRaman
          ifAmplifierEdfa
          ifIwdmPath
          ifFhCpri
          ifFhObsai
          ifPhysicalCage
          ifEthRsFec
          ifPerfDelay
          ifOtdr
"
    DEFVAL { 0 }
    ::= { ifBasicSignalEntry 3 }

ifBasicSignalSignalFormat OBJECT-TYPE
    SYNTAX      SignalFormat
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The signal format.

"
    DEFVAL { unused }
    ::= { ifBasicSignalEntry 4 }

ifBasicSignalFarEndLoopbackTerminatingLayer OBJECT-TYPE
    SYNTAX      Layer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The layer where the far end loopback (a.k.a.
         terminal loopback for a client interface and
         facility loopback for a line interface) is done.
         This is coded in a bitmask

"
    ::= { ifBasicSignalEntry 5 }

ifBasicSignalFarEndLoopback OBJECT-TYPE
    SYNTAX     EnabledDisabledWithNA
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The far end loopback (a.k.a. terminal loopback for
         a client interface and facility loopback for a line
         interface) setting.

        disabled - Far end loopback is not set. This is the
        default setting.

        enabled - Far end loopback is set.

"
    DEFVAL { disabled }
    ::= { ifBasicSignalEntry 6 }

ifBasicSignalFarEndLoopbackTimeout OBJECT-TYPE
    SYNTAX      Time7200min
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Timeout for far end loopback (a.k.a. terminal
         loopback for a client interface and facility
         loopback for a line interfac) to make sure
         connection to node is not lost if ppp link is
         broken. The unit is minutes. The value 0 is used in
         SNMP to indicate that the setting will last forever.

         Note! This attribute is not saved in backup,
         meaning the loopback will be set to disabled
         when rebooting CU.

"
    DEFVAL { 3 }
    ::= { ifBasicSignalEntry 7 }

ifBasicSignalNearEndLoopbackTerminatingLayer OBJECT-TYPE
    SYNTAX      Layer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The layer where the near end loopback (a.k.a.
         terminal loopback for a line interface and facility
         loopback for a client interface) is done.
         This is coded in a bitmask.

"
    ::= { ifBasicSignalEntry 8 }

ifBasicSignalNearEndLoopback OBJECT-TYPE
    SYNTAX     EnabledDisabledWithNA
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The near end loopback (a.k.a. terminal
        loopback for a line interface and facility loopback
        for a client interface) setting.

        disabled - Near end loopback is not set. This is the
        default setting.

        enabled - Near end loopback is set.

"
    DEFVAL { disabled }
    ::= { ifBasicSignalEntry 9 }

ifBasicSignalNearEndLoopbackTimeout OBJECT-TYPE
    SYNTAX      Time7200min
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Timeout for near end loopback (a.k.a. terminal
         loopback for a line interface and facility loopback
         for a client interface) to make sure connection to
         node is not lost if ppp link is broken. The unit is
         minutes. The value 0 is used in SNMP to indicate
         that the setting will last forever.

         Note! This attribute is not saved in backup,
         meaning the loopback will be set to disabled
         when rebooting CU.

"
    DEFVAL { 3 }
    ::= { ifBasicSignalEntry 10 }

ifBasicSignalFarEndLoopbackEnabled OBJECT-TYPE
    SYNTAX      FaultStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Far end end loopback (a.k.a. terminal loopback for
         a client interface and facility loopback for a line
         interface) is enabled.

        alarm: Far end loopback is enabled.

        ok: Far end loopback is disabled.

"
    ::= { ifBasicSignalEntry 11 }

ifBasicSignalNearEndLoopbackEnabled OBJECT-TYPE
    SYNTAX      FaultStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Near end end loopback (a.k.a. terminal loopback for
         a line interface and facility loopback for a client
         interface) is enabled.

        alarm: Near end loopback is enabled.

        ok: Near end loopback is disabled.

"
    ::= { ifBasicSignalEntry 12 }

ifBasicSignalOpticalLayerMapping OBJECT-TYPE
    SYNTAX      OpticalLayerMappingType
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The optical layer mapping.

"
    DEFVAL { singleOpticalChannel }
    ::= { ifBasicSignalEntry 13 }

ifBasicSignalConfigurationMismatch OBJECT-TYPE
    SYNTAX      FaultStatusWithNA
    MAX-ACCESS  read-only
    STATUS      deprecated
    DESCRIPTION
        "The inserted transceiver does not support the
        configuration of the optical layer mapping.

        alarm: A transceiver with other supported optical layer
               mapping than the requested mapping is inserted.

        ok: The transceiver with the non-requested optical
            layer mapping is removed, or the object is reconfigured.

"
    ::= { ifBasicSignalEntry 14 }

ifBasicSignalActualOpticalLayerMapping OBJECT-TYPE
    SYNTAX      OpticalLayerMappingType
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The actual optical layer mapping.

"
    DEFVAL { undefined }
    ::= { ifBasicSignalEntry 15 }

ifBasicSignalSpeed OBJECT-TYPE
    SYNTAX      Unsigned32WithNA (61440..1402500|2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The expected signal bit rate in units of
        10,000 bits (0.01 Mb) per second.

"

    DEFVAL { 61440 }
    ::= { ifBasicSignalEntry 16 }

ifBasicSignalDirection OBJECT-TYPE
    SYNTAX      SignalDirection
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The direction in which this object is
        referred to.

        rx    - In bound direction. (1)

        tx    - out bound direction. (2)

        biDir - the interface has one connector used for both rx and tx. (3)

        txRx  - the interface has two connectors one for tx and one for rx. (4)

        Not Available - the direction is not available.

"

    DEFVAL { txRx }
    ::= { ifBasicSignalEntry 17 }

ifBasicSignalFormatConfigurable OBJECT-TYPE
    SYNTAX INTEGER {
        true (1),
        false (2),
        notApplicable (2147483647)
        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This atttribute indicates if the interface is format configurable or not

        true    -  The interface is format configurable

        false    - The interface is not format configurable

"

    ::= { ifBasicSignalEntry 18 }

ifBasicSignalFormatConfigurationSharedWithInterface OBJECT-TYPE
    SYNTAX      Unsigned32WithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This attribute specifies whether this object instances shares the format
        configuration with another object instance.
           value == 0: it is not shared
           value != 0: it is shared with the interface object with index = value in IfBasicIfEntry
        If it is shared, it means that updating the format (and optionally speed)
        will affect the configuration of the other object instance

"

    ::= { ifBasicSignalEntry 19 }

ifBasicSignalPhysicalLayerMapping OBJECT-TYPE
    SYNTAX      PhysicalLayerMappingType
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The expected physical layer mapping.

"
    DEFVAL { dualFiber }
    ::= { ifBasicSignalEntry 20 }

ifBasicSignalFacilityLoopback OBJECT-TYPE
    SYNTAX     EnabledDisabledWithNA
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The facility loopback setting. Rx is looped to Tx.
        The purpose of facility loopback is to test
        the line interface termination.

        disabled - Facility loopback is not set. This is the
        default setting.

        enabled - Facility loopback is set.

"
    DEFVAL { disabled }
    ::= { ifBasicSignalEntry 21 }

ifBasicSignalFacilityLoopbackTimeout OBJECT-TYPE
    SYNTAX      Time7200minNo0
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Timeout for facility loopback to make sure
         connection to node is not lost if ppp link is
         broken. The unit is minutes.

         Note! This attribute is not saved in backup,
         meaning the loopback will be set to disabled
         when rebooting CU.

"
    DEFVAL { 3 }
    ::= { ifBasicSignalEntry 22 }

ifBasicSignalFacilityLoopbackEnabled OBJECT-TYPE
    SYNTAX      FaultStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Facility loopback is enabled.

        alarm: Facility loopback is enabled.

        ok: Facility loopback is disabled.

"
    ::= { ifBasicSignalEntry 23 }

ifBasicSignalTerminalLoopback OBJECT-TYPE
    SYNTAX     EnabledDisabledWithNA
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The terminal loopback setting. Tx is looped to Rx.
        The purpose of a terminal loopback is to test
        the path through the equipment (a cross-connect,
        mux/demux stage, or similar) and execute the loop
        close to the outgoing interface.

        disabled - Terminal loopback is not set. This is the
        default setting.

        enabled - Terminal loopback is set.

"
    DEFVAL { disabled }
    ::= { ifBasicSignalEntry 24 }

ifBasicSignalTerminalLoopbackTimeout OBJECT-TYPE
    SYNTAX      Time7200minNo0
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Timeout for terminal loopback to make sure connection to
         node is not lost if ppp link is broken. The unit is
         minutes.

         Note! This attribute is not saved in backup,
         meaning the loopback will be set to disabled
         when rebooting CU.

"
    DEFVAL { 3 }
    ::= { ifBasicSignalEntry 25 }

ifBasicSignalTerminalLoopbackEnabled OBJECT-TYPE
    SYNTAX      FaultStatusWithNA
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Terminal loopback is enabled.

        alarm: Terminal loopback is enabled.

        ok: Terminal loopback is disabled.

"
    ::= { ifBasicSignalEntry 26 }

ifBasicSignalConnectorType OBJECT-TYPE
    SYNTAX      ConnectorType
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The connector type.

"
    DEFVAL { notApplicable }
    ::= { ifBasicSignalEntry 27 }

-- ----------------------------------------------------
-- Notifications
-- ----------------------------------------------------


-- ----------------------------------------------------
-- Object and event groups
-- ----------------------------------------------------

ifBasicGeneralGroupV1 OBJECT-GROUP
    OBJECTS {
        ifBasicGeneralConfigLastChangeTime,
        ifBasicGeneralStateLastChangeTime,
        ifBasicGeneralIfBasicIfTableSize,
        ifBasicGeneralIfBasicIfConfigLastChangeTime,
        ifBasicGeneralIfBasicIfStateLastChangeTime,
        ifBasicGeneralIfBasicAdminTableSize,
        ifBasicGeneralIfBasicAdminConfigLastChangeTime,
        ifBasicGeneralIfBasicAdminStateLastChangeTime,
        ifBasicGeneralIfBasicSignalTableSize,
        ifBasicGeneralIfBasicSignalConfigLastChangeTime,
        ifBasicGeneralIfBasicSignalStateLastChangeTime }

    STATUS      current
    DESCRIPTION
        "The general objects."
    ::= { lumIfBasicGroups 1 }

ifBasicIfGroupV1 OBJECT-GROUP
    OBJECTS {
        ifBasicIfIndex,
        ifBasicIfName,
        ifBasicIfTxSignalStatus,
        ifBasicIfRxSignalStatus }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic if objects (R20.0)."
    ::= { lumIfBasicGroups 2 }

ifBasicAdminGroupV1 OBJECT-GROUP
    OBJECTS {
        ifBasicAdminIndex,
        ifBasicAdminName,
        ifBasicAdminDescr,
        ifBasicAdminSubrack,
        ifBasicAdminSlot,
        ifBasicAdminTxPort,
        ifBasicAdminRxPort,
        ifBasicAdminAdminStatus,
        ifBasicAdminOperStatus,
        ifBasicAdminAutoAlarmEnableStatus,
        ifBasicAdminAutoAlarmEnableReset }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic admin objects (R20.0)."
    ::= { lumIfBasicGroups 3 }

ifBasicSignalGroupV1 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled}
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R20.0)."
    ::= { lumIfBasicGroups 4 }

ifBasicSignalGroupV2 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping}
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R22.0)."
    ::= { lumIfBasicGroups 5 }

ifBasicSignalGroupV3 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping,
        ifBasicSignalConfigurationMismatch,
        ifBasicSignalActualOpticalLayerMapping}
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R23.0)."
    ::= { lumIfBasicGroups 6 }

ifBasicSignalGroupV4 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping,
        ifBasicSignalConfigurationMismatch,
        ifBasicSignalActualOpticalLayerMapping,
        ifBasicSignalSpeed,
        ifBasicSignalDirection,
        ifBasicSignalFormatConfigurable,
        ifBasicSignalFormatConfigurationSharedWithInterface}
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R26.0)."
    ::= { lumIfBasicGroups 7 }

ifBasicIfGroupV2 OBJECT-GROUP
    OBJECTS {
        ifBasicIfIndex,
        ifBasicIfName,
        ifBasicIfTxSignalStatus,
        ifBasicIfRxSignalStatus,
        ifBasicIfUpId }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic if objects (R26.0)."
    ::= { lumIfBasicGroups 8 }

ifBasicSignalGroupV5 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping,
        ifBasicSignalConfigurationMismatch,
        ifBasicSignalActualOpticalLayerMapping,
        ifBasicSignalSpeed,
        ifBasicSignalDirection,
        ifBasicSignalFormatConfigurable,
        ifBasicSignalFormatConfigurationSharedWithInterface,
        ifBasicSignalPhysicalLayerMapping }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R26.1)."
    ::= { lumIfBasicGroups 9 }

ifBasicSignalGroupV6 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping,
        ifBasicSignalConfigurationMismatch,
        ifBasicSignalActualOpticalLayerMapping,
        ifBasicSignalSpeed,
        ifBasicSignalDirection,
        ifBasicSignalFormatConfigurable,
        ifBasicSignalFormatConfigurationSharedWithInterface,
        ifBasicSignalPhysicalLayerMapping,
        ifBasicSignalFacilityLoopback,
        ifBasicSignalFacilityLoopbackTimeout,
        ifBasicSignalFacilityLoopbackEnabled,
        ifBasicSignalTerminalLoopback,
        ifBasicSignalTerminalLoopbackTimeout,
        ifBasicSignalTerminalLoopbackEnabled }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic signal objects (R28.0)."
    ::= { lumIfBasicGroups 10 }

ifBasicAdminGroupV2 OBJECT-GROUP
    OBJECTS {
        ifBasicAdminIndex,
        ifBasicAdminName,
        ifBasicAdminDescr,
        ifBasicAdminSubrack,
        ifBasicAdminSlot,
        ifBasicAdminTxPort,
        ifBasicAdminRxPort,
        ifBasicAdminAdminStatus,
        ifBasicAdminOperStatus,
        ifBasicAdminAutoAlarmEnableStatus,
        ifBasicAdminAutoAlarmEnableReset,
        ifBasicAdminInterfaceStatus }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic admin objects (R28.0)."
    ::= { lumIfBasicGroups 11 }

ifBasicIfGroupV3 OBJECT-GROUP
    OBJECTS {
        ifBasicIfIndex,
        ifBasicIfName,
        ifBasicIfTxSignalStatus,
        ifBasicIfRxSignalStatus,
        ifBasicIfUpId,
        ifBasicIfAid,
        ifBasicIfPhysicalLocation }
    STATUS      current
    DESCRIPTION
        "The ifBasic if objects (R28.0)."
    ::= { lumIfBasicGroups 12 }

ifBasicAdminGroupV3 OBJECT-GROUP
    OBJECTS {
        ifBasicAdminIndex,
        ifBasicAdminName,
        ifBasicAdminDescr,
        ifBasicAdminSubrack,
        ifBasicAdminSlot,
        ifBasicAdminTxPort,
        ifBasicAdminRxPort,
        ifBasicAdminAdminStatus,
        ifBasicAdminOperStatus,
        ifBasicAdminAutoAlarmEnableStatus,
        ifBasicAdminAutoAlarmEnableReset,
        ifBasicAdminInterfaceStatus,
        ifBasicAdminIfNo,
        ifBasicAdminIfType }
    STATUS      deprecated
    DESCRIPTION
        "The ifBasic admin objects (R31.0)."
    ::= { lumIfBasicGroups 13 }

ifBasicSignalGroupV7 OBJECT-GROUP
    OBJECTS {
        ifBasicSignalIndex,
        ifBasicSignalName,
        ifBasicSignalSignalStructure,
        ifBasicSignalSignalFormat,
        ifBasicSignalFarEndLoopbackTerminatingLayer,
        ifBasicSignalFarEndLoopback,
        ifBasicSignalFarEndLoopbackTimeout,
        ifBasicSignalNearEndLoopbackTerminatingLayer,
        ifBasicSignalNearEndLoopback,
        ifBasicSignalNearEndLoopbackTimeout,
        ifBasicSignalFarEndLoopbackEnabled,
        ifBasicSignalNearEndLoopbackEnabled,
        ifBasicSignalOpticalLayerMapping,
        ifBasicSignalConfigurationMismatch,
        ifBasicSignalActualOpticalLayerMapping,
        ifBasicSignalSpeed,
        ifBasicSignalDirection,
        ifBasicSignalFormatConfigurable,
        ifBasicSignalFormatConfigurationSharedWithInterface,
        ifBasicSignalPhysicalLayerMapping,
        ifBasicSignalFacilityLoopback,
        ifBasicSignalFacilityLoopbackTimeout,
        ifBasicSignalFacilityLoopbackEnabled,
        ifBasicSignalTerminalLoopback,
        ifBasicSignalTerminalLoopbackTimeout,
        ifBasicSignalTerminalLoopbackEnabled,
        ifBasicSignalConnectorType }
    STATUS      current
    DESCRIPTION
        "The ifBasic signal objects (R31.0)."
    ::= { lumIfBasicGroups 14 }


ifBasicAdminGroupV4 OBJECT-GROUP
    OBJECTS {
        ifBasicAdminIndex,
        ifBasicAdminName,
        ifBasicAdminDescr,
        ifBasicAdminSubrack,
        ifBasicAdminSlot,
        ifBasicAdminTxPort,
        ifBasicAdminRxPort,
        ifBasicAdminAdminStatus,
        ifBasicAdminOperStatus,
        ifBasicAdminAutoAlarmEnableStatus,
        ifBasicAdminAutoAlarmEnableReset,
        ifBasicAdminInterfaceStatus,
        ifBasicAdminIfNo,
        ifBasicAdminIfType,
        ifBasicAdminNotAvailableForUse }
    STATUS      current
    DESCRIPTION
        "The ifBasic admin objects (R32.0)."
    ::= { lumIfBasicGroups 15 }

-- ----------------------------------------------------
-- Compliance
-- ----------------------------------------------------

lumIfBasicBasicComplV1 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R20.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV1,
            ifBasicAdminGroupV1,
            ifBasicSignalGroupV1 }
    ::= { lumIfBasicCompl 1 }

lumIfBasicBasicComplV2 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R22.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV1,
            ifBasicAdminGroupV1,
            ifBasicSignalGroupV2 }
    ::= { lumIfBasicCompl 2 }

lumIfBasicBasicComplV3 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R23.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV1,
            ifBasicAdminGroupV1,
            ifBasicSignalGroupV3 }
    ::= { lumIfBasicCompl 3 }

lumIfBasicBasicComplV4 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R26.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV2,
            ifBasicAdminGroupV1,
            ifBasicSignalGroupV4 }
    ::= { lumIfBasicCompl 4 }

lumIfBasicBasicComplV5 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R26.1)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV2,
            ifBasicAdminGroupV1,
            ifBasicSignalGroupV5 }
    ::= { lumIfBasicCompl 5 }

lumIfBasicBasicComplV6 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R28.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV3,
            ifBasicAdminGroupV2,
            ifBasicSignalGroupV6 }
    ::= { lumIfBasicCompl 6 }

lumIfBasicBasicComplV7 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R31.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV3,
            ifBasicAdminGroupV3,
            ifBasicSignalGroupV7 }
    ::= { lumIfBasicCompl 7 }

lumIfBasicBasicComplV8 MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
        "Basic implementation requirements for the ifBasic MIB. (R32.0)"
    MODULE
        MANDATORY-GROUPS {
            ifBasicGeneralGroupV1,
            ifBasicIfGroupV3,
            ifBasicAdminGroupV4,
            ifBasicSignalGroupV7 }
    ::= { lumIfBasicCompl 8 }
END