mibs/MIBS/ADSL-LINE-EXT-MIB

1222 lines
48 KiB
Plaintext
Raw Normal View History

2023-12-05 12:25:34 +01:00
-- file: ADSL-LINE-EXT-MIB.my
-- Extracted from RFC3440 by MG-SOFT Corp.
-- Changes:
-- No changes needed.
-- http://www.mg-soft.com/
ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter32,
Integer32,
NOTIFICATION-TYPE,
MODULE-IDENTITY,
OBJECT-TYPE FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
TEXTUAL-CONVENTION FROM SNMPv2-TC
PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB
AdslPerfCurrDayCount,
AdslPerfPrevDayCount FROM ADSL-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
adslLineAlarmConfProfileEntry,
adslLineConfProfileEntry,
adslAturIntervalEntry,
adslAturPerfDataEntry,
adslAtucIntervalEntry,
adslAtucPerfDataEntry,
adslLineEntry,
adslMIB FROM ADSL-LINE-MIB
;
adslExtMIB MODULE-IDENTITY
LAST-UPDATED "200212100000Z" -- 10 Dec 2002
ORGANIZATION "IETF ADSL MIB Working Group"
CONTACT-INFO
"
Faye Ly
Pedestal Networks
6503 Dumbarton Circle,
Fremont, CA 94555
Tel: +1 510-578-0158
Fax: +1 510-744-5152
E-Mail: faye@pedestalnetworks.com
Gregory Bathrick
Nokia Networks
2235 Mercury Way,
Fax: +1 707-535-7300
E-Mail: greg.bathrick@nokia.com
General Discussion:adslmib@ietf.org
To Subscribe: https://www1.ietf.org/mailman/listinfo/adslmib
Archive: https://www1.ietf.org/mailman/listinfo/adslmib
"
DESCRIPTION
"Copyright (C) The Internet Society (2002). This version of
this MIB module is part of RFC 3440; see the RFC itself for
full legal notices.
This MIB Module is a supplement to the ADSL-LINE-MIB
[RFC2662]."
REVISION "200212100000Z" -- 10 dec 2002
DESCRIPTION "Initial Version, published as RFC 3440. This MIB
module supplements the ADSL-LINE-MIB [RFC2662]."
::= { adslMIB 3 }
adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 }
AdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A set of ADSL line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate
and G.Lite respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F)
"
SYNTAX BITS {
ansit1413(0),
etsi(1),
q9921PotsNonOverlapped(2),
q9921PotsOverlapped(3),
q9921IsdnNonOverlapped(4),
q9921isdnOverlapped(5),
q9921tcmIsdnNonOverlapped(6),
q9921tcmIsdnOverlapped(7),
q9922potsNonOverlapeed(8),
q9922potsOverlapped(9),
q9922tcmIsdnNonOverlapped(10),
q9922tcmIsdnOverlapped(11),
q9921tcmIsdnSymmetric(12)
}
adslLineExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslLineExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is an extension of RFC 2662. It
contains ADSL line configuration and
monitoring information. This includes the ADSL
line's capabilities and actual ADSL transmission
system."
::= { adslExtMibObjects 17 }
adslLineExtEntry OBJECT-TYPE
SYNTAX AdslLineExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslLineEntry defined in
[RFC2662]. Each entry corresponds to an ADSL
line."
AUGMENTS { adslLineEntry }
::= { adslLineExtTable 1 }
AdslLineExtEntry ::=
SEQUENCE {
adslLineTransAtucCap AdslTransmissionModeType,
adslLineTransAtucConfig AdslTransmissionModeType,
adslLineTransAtucActual AdslTransmissionModeType,
adslLineGlitePowerState INTEGER,
adslLineConfProfileDualLite SnmpAdminString
}
adslLineTransAtucCap OBJECT-TYPE
SYNTAX AdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transmission modes, represented by a
bitmask that the ATU-C is capable of
supporting. The modes available are limited
by the design of the equipment."
REFERENCE "Section 7.3.2 ITU G.997.1"
::= { adslLineExtEntry 1 }
adslLineTransAtucConfig OBJECT-TYPE
SYNTAX AdslTransmissionModeType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The transmission modes, represented by a bitmask,
currently enabled by the ATU-C. The manager can
only set those modes that are supported by the
ATU-C. An ATU-C's supported modes are provided by
AdslLineTransAtucCap."
REFERENCE "Section 7.3.2 ITU G.997.1"
::= { adslLineExtEntry 2 }
adslLineTransAtucActual OBJECT-TYPE
SYNTAX AdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual transmission mode of the ATU-C.
During ADSL line initialization, the ADSL
Transceiver Unit - Remote terminal end (ATU-R)
will determine the mode used for the link.
This value will be limited a single transmission
mode that is a subset of those modes enabled
by the ATU-C and denoted by
adslLineTransAtucConfig. After an initialization
has occurred, its mode is saved as the 'Current'
mode and is persistence should the link go
down. This object returns 0 (i.e. BITS with no
mode bit set) if the mode is not known."
REFERENCE "Section 7.3.2 ITU G.997.1 "
::= { adslLineExtEntry 3 }
adslLineGlitePowerState OBJECT-TYPE
SYNTAX INTEGER {
none(1),
l0(2), -- L0 Power on
l1(3), -- L1 Power on but reduced
l3(4) -- L3 Power off
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object specifies the power
state of this interface. L0 is power on, L1 is
power on but reduced and L3 is power off. Power
state cannot be configured by an operator but it
can be viewed via the ifOperStatus object for the
managed ADSL interface. The value of the object
ifOperStatus is set to down(2) if the ADSL
interface is in power state L3 and is set to up(1)
if the ADSL line interface is in power state L0 or
L1. If the object adslLineTransAtucActual is set to
a G.992.2 (G.Lite)-type transmission mode, the
value of this object will be one of the valid power
states: L0(2), L1(3), or L3(4). Otherwise, its
value will be none(1)."
::= { adslLineExtEntry 4 }
adslLineConfProfileDualLite OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object extends the definition an ADSL line and
associated channels (when applicable) for cases
when it is configured in dual mode, and operating
in a G.Lite-type mode as denoted by
adslLineTransAtucActual. Dual mode exists when the
object, adslLineTransAtucConfig, is configured with
one or more full-rate modes and one or more G.Lite
modes simultaneously.
When 'dynamic' profiles are implemented, the value
of object is equal to the index of the applicable
row in the ADSL Line Configuration Profile Table,
AdslLineConfProfileTable defined in ADSL-MIB
[RFC2662].
In the case when dual-mode has not been enabled,
the value of the object will be equal to the value
of the object adslLineConfProfile [RFC2662].
When `static' profiles are implemented, in much
like the case of the object,
adslLineConfProfileName [RFC2662], this object's
value will need to algorithmically represent the
characteristics of the line. In this case, the
value of the line's ifIndex plus a value indicating
the line mode type (e.g., G.Lite, Full-rate) will
be used. Therefore, the profile's name is a string
concatenating the ifIndex and one of the follow
values: Full or Lite. This string will be
fixed-length (i.e., 14) with leading zero(s). For
example, the profile name for ifIndex that equals
'15' and is a full rate line, it will be
'0000000015Full'."
REFERENCE "Section 5.4 Profiles, RFC 2662"
::= { adslLineExtEntry 5 }
adslAtucPerfDataExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends adslAtucPerfDataTable [RFC2662]
with additional ADSL physical line counter
information such as unavailable seconds-line and
severely errored seconds-line."
::= { adslExtMibObjects 18 }
adslAtucPerfDataExtEntry OBJECT-TYPE
SYNTAX AdslAtucPerfDataExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslAtucPerfDataEntry defined
in [RFC2662]. Each entry corresponds to an ADSL
line."
AUGMENTS { adslAtucPerfDataEntry }
::= { adslAtucPerfDataExtTable 1 }
AdslAtucPerfDataExtEntry ::=
SEQUENCE {
adslAtucPerfStatFastR Counter32,
adslAtucPerfStatFailedFastR Counter32,
adslAtucPerfStatSesL Counter32,
adslAtucPerfStatUasL Counter32,
adslAtucPerfCurr15MinFastR PerfCurrentCount,
adslAtucPerfCurr15MinFailedFastR PerfCurrentCount,
adslAtucPerfCurr15MinSesL PerfCurrentCount,
adslAtucPerfCurr15MinUasL PerfCurrentCount,
adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount,
adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount,
adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount,
adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount,
adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount,
adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount,
adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount,
adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount
}
adslAtucPerfStatFastR OBJECT-TYPE
SYNTAX Counter32
UNITS "line retrains"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
the number of fast line bs since last
agent reset."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 1 }
adslAtucPerfStatFailedFastR OBJECT-TYPE
SYNTAX Counter32
UNITS "line retrains"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
the number of failed fast line retrains since
last agent reset."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 2 }
adslAtucPerfStatSesL OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
the number of severely errored seconds-line since
last agent reset."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 3 }
adslAtucPerfStatUasL OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
the number of unavailable seconds-line since
last agent reset."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 4 }
adslAtucPerfCurr15MinFastR OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAtucPerfCurr15MinFastR reports the current
number of seconds during which there have been
fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 5 }
adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAtucPerfCurr15MinFailedFastR reports the
current number of seconds during which there
have been failed fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 6 }
adslAtucPerfCurr15MinSesL OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAtucPerfCurr15MinSesL reports the current
number of seconds during which there have been
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 7 }
adslAtucPerfCurr15MinUasL OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAtucPerfCurr15MinUasL reports the current
number of seconds during which there have been
unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 8 }
adslAtucPerfCurr1DayFastR OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayFastR reports the number
of seconds during which there have been
fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 9 }
adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayFailedFastR reports the
number of seconds during which there have been
failed fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 10 }
adslAtucPerfCurr1DaySesL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DaySesL reports the
number of seconds during which there have been
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 11 }
adslAtucPerfCurr1DayUasL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
adslAtucPerfCurr1DayUasL reports the
number of seconds during which there have been
unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 12 }
adslAtucPerfPrev1DayFastR OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayFastR
reports the number of seconds during which there
were fast retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
::= { adslAtucPerfDataExtEntry 13 }
adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day,
adslAtucPerfPrev1DayFailedFastR reports the number
of seconds during which there were failed fast
retrains."
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
::= { adslAtucPerfDataExtEntry 14 }
adslAtucPerfPrev1DaySesL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAtucPerfPrev1DaySesL
reports the number of seconds during which there
were severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAtucPerfDataExtEntry 15 }
adslAtucPerfPrev1DayUasL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAtucPerfPrev1DayUasL
reports the number of seconds during which there
were unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
::= { adslAtucPerfDataExtEntry 16 }
adslAtucIntervalExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATU-C
performance data collection interval for
ADSL physical interfaces whose
IfEntries' ifType is equal to adsl(94)."
::= { adslExtMibObjects 19 }
adslAtucIntervalExtEntry OBJECT-TYPE
SYNTAX AdslAtucIntervalExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the
adslAtucIntervalExtTable."
AUGMENTS { adslAtucIntervalEntry }
::= { adslAtucIntervalExtTable 1 }
AdslAtucIntervalExtEntry ::=
SEQUENCE {
adslAtucIntervalFastR PerfIntervalCount,
adslAtucIntervalFailedFastR PerfIntervalCount,
adslAtucIntervalSesL PerfIntervalCount,
adslAtucIntervalUasL PerfIntervalCount
}
adslAtucIntervalFastR OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current interval, adslAtucIntervalFastR
reports the current number of seconds during which
there have been fast retrains."
::= { adslAtucIntervalExtEntry 1 }
adslAtucIntervalFailedFastR OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAtucIntervalFailedFastR
reports the number of seconds during which
there have been failed fast retrains."
::= { adslAtucIntervalExtEntry 2 }
adslAtucIntervalSesL OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAtucIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line."
::= { adslAtucIntervalExtEntry 3 }
adslAtucIntervalUasL OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAtucIntervalUasL
reports the number of seconds during which
there have been unavailable seconds-line."
::= { adslAtucIntervalExtEntry 4 }
adslAturPerfDataExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ADSL physical line counters
not defined in the adslAturPerfDataTable
from the ADSL-LINE-MIB [RFC2662]."
::= { adslExtMibObjects 20 }
adslAturPerfDataExtEntry OBJECT-TYPE
SYNTAX AdslAturPerfDataExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslAturPerfDataEntry defined
in [RFC2662]. Each entry corresponds to an ADSL
line."
AUGMENTS { adslAturPerfDataEntry }
::= { adslAturPerfDataExtTable 1 }
AdslAturPerfDataExtEntry ::=
SEQUENCE {
adslAturPerfStatSesL Counter32,
adslAturPerfStatUasL Counter32,
adslAturPerfCurr15MinSesL PerfCurrentCount,
adslAturPerfCurr15MinUasL PerfCurrentCount,
adslAturPerfCurr1DaySesL AdslPerfCurrDayCount,
adslAturPerfCurr1DayUasL AdslPerfCurrDayCount,
adslAturPerfPrev1DaySesL AdslPerfPrevDayCount,
adslAturPerfPrev1DayUasL AdslPerfPrevDayCount
}
adslAturPerfStatSesL OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
severely errored second-line since the last agent
reset."
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
::= { adslAturPerfDataExtEntry 1 }
adslAturPerfStatUasL OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reports the count of
unavailable seconds-line since the last agent
reset."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 2 }
adslAturPerfCurr15MinSesL OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAturPerfCurr15MinSesL reports the current
number of seconds during which there have been
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 3 }
adslAturPerfCurr15MinUasL OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current 15-minute interval,
adslAturPerfCurr15MinUasL reports the current
number of seconds during which there have been
available seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 4 }
adslAturPerfCurr1DaySesL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAturPerfCurr1DayTimeElapsed [RFC2662],
adslAturPerfCurr1DaySesL reports the
number of seconds during which there have been
severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 5 }
adslAturPerfCurr1DayUasL OBJECT-TYPE
SYNTAX AdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the current day as measured by
adslAturPerfCurr1DayTimeElapsed [RFC2662],
adslAturPerfCurr1DayUasL reports the
number of seconds during which there have been
unavailable seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 6 }
adslAturPerfPrev1DaySesL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAturPerfPrev1DaySesL
reports the number of seconds during which there
were severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
::= { adslAturPerfDataExtEntry 7 }
adslAturPerfPrev1DayUasL OBJECT-TYPE
SYNTAX AdslPerfPrevDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the previous day, adslAturPerfPrev1DayUasL
reports the number of seconds during which there
were severely errored seconds-line."
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
::= { adslAturPerfDataExtEntry 8 }
adslAturIntervalExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAturIntervalExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each ATU-R
performance data collection interval for
ADSL physical interfaces whose
IfEntries' ifType is equal to adsl(94)."
::= { adslExtMibObjects 21 }
adslAturIntervalExtEntry OBJECT-TYPE
SYNTAX AdslAturIntervalExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the
adslAturIntervalExtTable."
AUGMENTS { adslAturIntervalEntry }
::= { adslAturIntervalExtTable 1 }
AdslAturIntervalExtEntry ::=
SEQUENCE {
adslAturIntervalSesL PerfIntervalCount,
adslAturIntervalUasL PerfIntervalCount
}
adslAturIntervalSesL OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAturIntervalSesL
reports the number of seconds during which
there have been severely errored seconds-line."
::= { adslAturIntervalExtEntry 1 }
adslAturIntervalUasL OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the each interval, adslAturIntervalUasL
reports the number of seconds during which
there have been unavailable seconds-line."
::= { adslAturIntervalExtEntry 2 }
adslConfProfileExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The adslConfProfileExtTable extends the ADSL line
profile configuration information in the
adslLineConfProfileTable from the ADSL-LINE-MIB
[RFC2662] by adding the ability to configure the
ADSL physical line mode."
::= { adslExtMibObjects 22 }
adslConfProfileExtEntry OBJECT-TYPE
SYNTAX AdslConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslLineConfProfileEntry
defined in [RFC2662]. Each entry corresponds to an
ADSL line profile."
AUGMENTS { adslLineConfProfileEntry }
::= { adslConfProfileExtTable 1 }
AdslConfProfileExtEntry ::=
SEQUENCE {
adslConfProfileLineType INTEGER
}
adslConfProfileLineType OBJECT-TYPE
SYNTAX INTEGER {
noChannel (1), -- no channels exist
fastOnly (2), -- only fast channel exists
interleavedOnly (3), -- only interleaved channel
-- exist
fastOrInterleaved (4),-- either fast or interleaved
-- channels can exist, but
-- only one at any time
fastAndInterleaved (5)-- both the fast channel and
-- the interleaved channel
-- exist
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to configure the ADSL physical
line mode. It has following valid values:
noChannel(1), when no channels exist.
fastOnly(2), when only fast channel exists.
interleavedOnly(3), when only interleaved channel
exist.
fastOrInterleaved(4), when either fast or
interleaved channels can exist, but only one
at any time.
fastAndInterleaved(5), when both the fast channel
and the interleaved channel exist.
In the case when no value has been set, the default
Value is noChannel(1).
"
DEFVAL { fastOnly }
::= { adslConfProfileExtEntry 1 }
adslAlarmConfProfileExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the
adslLineAlarmConfProfileTable and provides
threshold parameters for all the counters defined
in this MIB module."
::= { adslExtMibObjects 23 }
adslAlarmConfProfileExtEntry OBJECT-TYPE
SYNTAX AdslAlarmConfProfileExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry extends the adslLineAlarmConfProfileTable
defined in [RFC2662]. Each entry corresponds to
an ADSL alarm profile."
AUGMENTS { adslLineAlarmConfProfileEntry }
::= { adslAlarmConfProfileExtTable 1 }
AdslAlarmConfProfileExtEntry ::=
SEQUENCE {
adslAtucThreshold15MinFailedFastR Integer32,
adslAtucThreshold15MinSesL Integer32,
adslAtucThreshold15MinUasL Integer32,
adslAturThreshold15MinSesL Integer32,
adslAturThreshold15MinUasL Integer32
}
adslAtucThreshold15MinFailedFastR OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerfCurr15MinFailedFastR
reaches or exceeds this value within a given
15-minute performance data collection period,
an adslAtucFailedFastRThreshTrap notification
will be generated. The value '0' will disable
the notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 1 }
adslAtucThreshold15MinSesL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerf15MinSesL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAtucSesLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 2 }
adslAtucThreshold15MinUasL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAtucPerf15MinUasL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAtucUasLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 3 }
adslAturThreshold15MinSesL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAturPerf15MinSesL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAturSesLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 4 }
adslAturThreshold15MinUasL OBJECT-TYPE
SYNTAX Integer32(0..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first time the value of the corresponding
instance of adslAturPerf15MinUasL reaches or
exceeds this value within a given 15-minute
performance data collection period, an
adslAturUasLThreshTrap notification will be
generated. The value '0' will disable the
notification. The default value of this
object is '0'."
DEFVAL { 0 }
::= { adslAlarmConfProfileExtEntry 5 }
-- definitions
adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 }
adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 }
adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 }
adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAtucPerfCurr15MinFailedFastR }
STATUS current
DESCRIPTION
"Failed Fast Retrains 15-minute threshold reached."
::= { adslExtAtucTrapsPrefix 1 }
adslAtucSesLThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAtucPerfCurr15MinSesL }
STATUS current
DESCRIPTION
"Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAtucTrapsPrefix 2 }
adslAtucUasLThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAtucPerfCurr15MinUasL }
STATUS current
DESCRIPTION
"Unavailable seconds-line 15-minute threshold
reached."
::= { adslExtAtucTrapsPrefix 3 }
adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 }
adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 }
adslAturSesLThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAturPerfCurr15MinSesL }
STATUS current
DESCRIPTION
"Severely errored seconds-line 15-minute threshold
reached."
::= { adslExtAturTrapsPrefix 1 }
adslAturUasLThreshTrap NOTIFICATION-TYPE
OBJECTS { adslAturPerfCurr15MinUasL }
STATUS current
DESCRIPTION
"Unavailable seconds-line 15-minute threshold
reached."
::= { adslExtAturTrapsPrefix 2 }
-- conformance information
adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 }
adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 }
adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 }
-- ATU-C agent compliance statements
adslExtLineMibAtucCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which
represent ADSL ATU-C interfaces."
MODULE -- this module
MANDATORY-GROUPS
{
adslExtLineGroup,
adslExtLineConfProfileControlGroup,
adslExtLineAlarmConfProfileGroup
}
GROUP adslExtAtucPhysPerfCounterGroup
DESCRIPTION
"This group is optional. Implementations which
require continuous ATU-C physical event counters
should implement this group."
GROUP adslExtAturPhysPerfCounterGroup
DESCRIPTION
"This group is optional. Implementations which
require continuous ATU-R physical event counters
should implement this group."
GROUP adslExtNotificationsGroup
DESCRIPTION
"This group is optional. Implementations which
support TCA (Threshold Crossing Alert) should
implement this group."
OBJECT adslAtucThreshold15MinFailedFastR
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAtucThreshold15MinSesL
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAtucThreshold15MinUasL
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAturThreshold15MinSesL
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslAturThreshold15MinUasL
MIN-ACCESS read-write
DESCRIPTION
"Read-write access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
OBJECT adslLineConfProfileDualLite
MIN-ACCESS read-only
DESCRIPTION
"Read-only access is applicable only when
static profiles as defined in ADSL Line MIB
[RFC2662] are implemented."
::= { adslExtCompliances 1 }
-- units of conformance
adslExtLineGroup OBJECT-GROUP
OBJECTS {
adslLineConfProfileDualLite,
adslLineTransAtucCap,
adslLineTransAtucConfig,
adslLineTransAtucActual,
adslLineGlitePowerState
}
STATUS current
DESCRIPTION
"A collection of objects providing extended
configuration information about an ADSL Line."
::= { adslExtGroups 1 }
adslExtAtucPhysPerfCounterGroup OBJECT-GROUP
OBJECTS {
adslAtucPerfStatFastR,
adslAtucPerfStatFailedFastR,
adslAtucPerfCurr15MinFastR,
adslAtucPerfCurr15MinFailedFastR,
adslAtucPerfCurr1DayFastR,
adslAtucPerfCurr1DayFailedFastR,
adslAtucPerfPrev1DayFastR,
adslAtucPerfPrev1DayFailedFastR,
adslAtucPerfStatSesL,
adslAtucPerfStatUasL,
adslAtucPerfCurr15MinSesL,
adslAtucPerfCurr15MinUasL,
adslAtucPerfCurr1DaySesL,
adslAtucPerfCurr1DayUasL,
adslAtucPerfPrev1DaySesL,
adslAtucPerfPrev1DayUasL,
adslAtucIntervalFastR,
adslAtucIntervalFailedFastR,
adslAtucIntervalSesL,
adslAtucIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 2 }
adslExtAturPhysPerfCounterGroup OBJECT-GROUP
OBJECTS {
adslAturPerfStatSesL,
adslAturPerfStatUasL,
adslAturPerfCurr15MinSesL,
adslAturPerfCurr15MinUasL,
adslAturPerfCurr1DaySesL,
adslAturPerfCurr1DayUasL,
adslAturPerfPrev1DaySesL,
adslAturPerfPrev1DayUasL,
adslAturIntervalSesL, adslAturIntervalUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end)."
::= { adslExtGroups 3 }
adslExtLineConfProfileControlGroup OBJECT-GROUP
OBJECTS {
adslConfProfileLineType
}
STATUS current
DESCRIPTION
"A collection of objects providing profile
control for the ADSL system."
::= { adslExtGroups 4 }
adslExtLineAlarmConfProfileGroup OBJECT-GROUP
OBJECTS {
adslAtucThreshold15MinFailedFastR,
adslAtucThreshold15MinSesL,
adslAtucThreshold15MinUasL,
adslAturThreshold15MinSesL,
adslAturThreshold15MinUasL
}
STATUS current
DESCRIPTION
"A collection of objects providing alarm profile
control for the ADSL system."
::= { adslExtGroups 5 }
adslExtNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
adslAtucFailedFastRThreshTrap,
adslAtucSesLThreshTrap,
adslAtucUasLThreshTrap,
adslAturSesLThreshTrap,
adslAturUasLThreshTrap
}
STATUS current
DESCRIPTION
"The collection of ADSL extension notifications."
::= { adslExtGroups 6 }
END