1222 lines
48 KiB
Plaintext
1222 lines
48 KiB
Plaintext
-- file: ADSL-LINE-EXT-MIB.my
|
|
-- Extracted from RFC3440 by MG-SOFT Corp.
|
|
-- Changes:
|
|
-- No changes needed.
|
|
-- http://www.mg-soft.com/
|
|
|
|
ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
Counter32,
|
|
Integer32,
|
|
NOTIFICATION-TYPE,
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE, OBJECT-GROUP,
|
|
NOTIFICATION-GROUP FROM SNMPv2-CONF
|
|
TEXTUAL-CONVENTION FROM SNMPv2-TC
|
|
PerfCurrentCount,
|
|
|
|
|
|
PerfIntervalCount FROM PerfHist-TC-MIB
|
|
AdslPerfCurrDayCount,
|
|
AdslPerfPrevDayCount FROM ADSL-TC-MIB
|
|
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
|
|
adslLineAlarmConfProfileEntry,
|
|
adslLineConfProfileEntry,
|
|
adslAturIntervalEntry,
|
|
adslAturPerfDataEntry,
|
|
adslAtucIntervalEntry,
|
|
adslAtucPerfDataEntry,
|
|
adslLineEntry,
|
|
adslMIB FROM ADSL-LINE-MIB
|
|
;
|
|
|
|
adslExtMIB MODULE-IDENTITY
|
|
|
|
LAST-UPDATED "200212100000Z" -- 10 Dec 2002
|
|
|
|
ORGANIZATION "IETF ADSL MIB Working Group"
|
|
|
|
CONTACT-INFO
|
|
"
|
|
Faye Ly
|
|
Pedestal Networks
|
|
6503 Dumbarton Circle,
|
|
Fremont, CA 94555
|
|
Tel: +1 510-578-0158
|
|
Fax: +1 510-744-5152
|
|
E-Mail: faye@pedestalnetworks.com
|
|
|
|
Gregory Bathrick
|
|
Nokia Networks
|
|
2235 Mercury Way,
|
|
Fax: +1 707-535-7300
|
|
E-Mail: greg.bathrick@nokia.com
|
|
|
|
General Discussion:adslmib@ietf.org
|
|
To Subscribe: https://www1.ietf.org/mailman/listinfo/adslmib
|
|
Archive: https://www1.ietf.org/mailman/listinfo/adslmib
|
|
"
|
|
DESCRIPTION
|
|
"Copyright (C) The Internet Society (2002). This version of
|
|
this MIB module is part of RFC 3440; see the RFC itself for
|
|
full legal notices.
|
|
|
|
This MIB Module is a supplement to the ADSL-LINE-MIB
|
|
[RFC2662]."
|
|
|
|
|
|
REVISION "200212100000Z" -- 10 dec 2002
|
|
DESCRIPTION "Initial Version, published as RFC 3440. This MIB
|
|
module supplements the ADSL-LINE-MIB [RFC2662]."
|
|
::= { adslMIB 3 }
|
|
|
|
adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 }
|
|
|
|
AdslTransmissionModeType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A set of ADSL line transmission modes, with one bit
|
|
per mode. The notes (F) and (L) denote Full-Rate
|
|
and G.Lite respectively:
|
|
Bit 00 : Regional Std. (ANSI T1.413) (F)
|
|
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
|
|
Bit 02 : G.992.1 POTS non-overlapped (F)
|
|
Bit 03 : G.992.1 POTS overlapped (F)
|
|
Bit 04 : G.992.1 ISDN non-overlapped (F)
|
|
Bit 05 : G.992.1 ISDN overlapped (F)
|
|
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
|
|
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
|
|
Bit 08 : G.992.2 POTS non-overlapped (L)
|
|
Bit 09 : G.992.2 POTS overlapped (L)
|
|
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
|
|
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
|
|
Bit 12 : G.992.1 TCM-ISDN symmetric (F)
|
|
"
|
|
SYNTAX BITS {
|
|
ansit1413(0),
|
|
etsi(1),
|
|
q9921PotsNonOverlapped(2),
|
|
q9921PotsOverlapped(3),
|
|
q9921IsdnNonOverlapped(4),
|
|
q9921isdnOverlapped(5),
|
|
q9921tcmIsdnNonOverlapped(6),
|
|
q9921tcmIsdnOverlapped(7),
|
|
q9922potsNonOverlapeed(8),
|
|
q9922potsOverlapped(9),
|
|
q9922tcmIsdnNonOverlapped(10),
|
|
q9922tcmIsdnOverlapped(11),
|
|
q9921tcmIsdnSymmetric(12)
|
|
}
|
|
|
|
adslLineExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslLineExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
|
|
|
|
"This table is an extension of RFC 2662. It
|
|
contains ADSL line configuration and
|
|
monitoring information. This includes the ADSL
|
|
line's capabilities and actual ADSL transmission
|
|
system."
|
|
::= { adslExtMibObjects 17 }
|
|
|
|
adslLineExtEntry OBJECT-TYPE
|
|
SYNTAX AdslLineExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry extends the adslLineEntry defined in
|
|
[RFC2662]. Each entry corresponds to an ADSL
|
|
line."
|
|
AUGMENTS { adslLineEntry }
|
|
::= { adslLineExtTable 1 }
|
|
|
|
AdslLineExtEntry ::=
|
|
SEQUENCE {
|
|
adslLineTransAtucCap AdslTransmissionModeType,
|
|
adslLineTransAtucConfig AdslTransmissionModeType,
|
|
adslLineTransAtucActual AdslTransmissionModeType,
|
|
adslLineGlitePowerState INTEGER,
|
|
adslLineConfProfileDualLite SnmpAdminString
|
|
}
|
|
|
|
adslLineTransAtucCap OBJECT-TYPE
|
|
SYNTAX AdslTransmissionModeType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The transmission modes, represented by a
|
|
bitmask that the ATU-C is capable of
|
|
supporting. The modes available are limited
|
|
by the design of the equipment."
|
|
REFERENCE "Section 7.3.2 ITU G.997.1"
|
|
::= { adslLineExtEntry 1 }
|
|
|
|
adslLineTransAtucConfig OBJECT-TYPE
|
|
SYNTAX AdslTransmissionModeType
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
|
|
DESCRIPTION
|
|
"The transmission modes, represented by a bitmask,
|
|
currently enabled by the ATU-C. The manager can
|
|
only set those modes that are supported by the
|
|
|
|
|
|
ATU-C. An ATU-C's supported modes are provided by
|
|
AdslLineTransAtucCap."
|
|
REFERENCE "Section 7.3.2 ITU G.997.1"
|
|
::= { adslLineExtEntry 2 }
|
|
|
|
adslLineTransAtucActual OBJECT-TYPE
|
|
SYNTAX AdslTransmissionModeType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The actual transmission mode of the ATU-C.
|
|
During ADSL line initialization, the ADSL
|
|
Transceiver Unit - Remote terminal end (ATU-R)
|
|
will determine the mode used for the link.
|
|
This value will be limited a single transmission
|
|
mode that is a subset of those modes enabled
|
|
by the ATU-C and denoted by
|
|
adslLineTransAtucConfig. After an initialization
|
|
has occurred, its mode is saved as the 'Current'
|
|
mode and is persistence should the link go
|
|
down. This object returns 0 (i.e. BITS with no
|
|
mode bit set) if the mode is not known."
|
|
REFERENCE "Section 7.3.2 ITU G.997.1 "
|
|
::= { adslLineExtEntry 3 }
|
|
|
|
adslLineGlitePowerState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
none(1),
|
|
l0(2), -- L0 Power on
|
|
l1(3), -- L1 Power on but reduced
|
|
l3(4) -- L3 Power off
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object specifies the power
|
|
state of this interface. L0 is power on, L1 is
|
|
power on but reduced and L3 is power off. Power
|
|
state cannot be configured by an operator but it
|
|
can be viewed via the ifOperStatus object for the
|
|
managed ADSL interface. The value of the object
|
|
ifOperStatus is set to down(2) if the ADSL
|
|
interface is in power state L3 and is set to up(1)
|
|
if the ADSL line interface is in power state L0 or
|
|
L1. If the object adslLineTransAtucActual is set to
|
|
a G.992.2 (G.Lite)-type transmission mode, the
|
|
value of this object will be one of the valid power
|
|
states: L0(2), L1(3), or L3(4). Otherwise, its
|
|
|
|
|
|
value will be none(1)."
|
|
::= { adslLineExtEntry 4 }
|
|
|
|
adslLineConfProfileDualLite OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object extends the definition an ADSL line and
|
|
associated channels (when applicable) for cases
|
|
when it is configured in dual mode, and operating
|
|
in a G.Lite-type mode as denoted by
|
|
adslLineTransAtucActual. Dual mode exists when the
|
|
object, adslLineTransAtucConfig, is configured with
|
|
one or more full-rate modes and one or more G.Lite
|
|
modes simultaneously.
|
|
|
|
When 'dynamic' profiles are implemented, the value
|
|
of object is equal to the index of the applicable
|
|
row in the ADSL Line Configuration Profile Table,
|
|
AdslLineConfProfileTable defined in ADSL-MIB
|
|
[RFC2662].
|
|
|
|
In the case when dual-mode has not been enabled,
|
|
the value of the object will be equal to the value
|
|
of the object adslLineConfProfile [RFC2662].
|
|
|
|
When `static' profiles are implemented, in much
|
|
like the case of the object,
|
|
adslLineConfProfileName [RFC2662], this object's
|
|
value will need to algorithmically represent the
|
|
characteristics of the line. In this case, the
|
|
value of the line's ifIndex plus a value indicating
|
|
the line mode type (e.g., G.Lite, Full-rate) will
|
|
be used. Therefore, the profile's name is a string
|
|
concatenating the ifIndex and one of the follow
|
|
values: Full or Lite. This string will be
|
|
fixed-length (i.e., 14) with leading zero(s). For
|
|
example, the profile name for ifIndex that equals
|
|
'15' and is a full rate line, it will be
|
|
'0000000015Full'."
|
|
REFERENCE "Section 5.4 Profiles, RFC 2662"
|
|
::= { adslLineExtEntry 5 }
|
|
|
|
adslAtucPerfDataExtTable OBJECT-TYPE
|
|
|
|
SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry
|
|
MAX-ACCESS not-accessible
|
|
|
|
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table extends adslAtucPerfDataTable [RFC2662]
|
|
with additional ADSL physical line counter
|
|
information such as unavailable seconds-line and
|
|
severely errored seconds-line."
|
|
::= { adslExtMibObjects 18 }
|
|
|
|
adslAtucPerfDataExtEntry OBJECT-TYPE
|
|
SYNTAX AdslAtucPerfDataExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry extends the adslAtucPerfDataEntry defined
|
|
in [RFC2662]. Each entry corresponds to an ADSL
|
|
line."
|
|
AUGMENTS { adslAtucPerfDataEntry }
|
|
::= { adslAtucPerfDataExtTable 1 }
|
|
|
|
AdslAtucPerfDataExtEntry ::=
|
|
SEQUENCE {
|
|
adslAtucPerfStatFastR Counter32,
|
|
adslAtucPerfStatFailedFastR Counter32,
|
|
adslAtucPerfStatSesL Counter32,
|
|
adslAtucPerfStatUasL Counter32,
|
|
adslAtucPerfCurr15MinFastR PerfCurrentCount,
|
|
adslAtucPerfCurr15MinFailedFastR PerfCurrentCount,
|
|
adslAtucPerfCurr15MinSesL PerfCurrentCount,
|
|
adslAtucPerfCurr15MinUasL PerfCurrentCount,
|
|
adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount,
|
|
adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount,
|
|
adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount,
|
|
adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount,
|
|
adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount,
|
|
adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount,
|
|
adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount,
|
|
adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount
|
|
}
|
|
|
|
adslAtucPerfStatFastR OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "line retrains"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
the number of fast line bs since last
|
|
agent reset."
|
|
|
|
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
|
|
::= { adslAtucPerfDataExtEntry 1 }
|
|
|
|
adslAtucPerfStatFailedFastR OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "line retrains"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
the number of failed fast line retrains since
|
|
last agent reset."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
|
|
::= { adslAtucPerfDataExtEntry 2 }
|
|
|
|
adslAtucPerfStatSesL OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
the number of severely errored seconds-line since
|
|
last agent reset."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
|
|
::= { adslAtucPerfDataExtEntry 3 }
|
|
|
|
adslAtucPerfStatUasL OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
the number of unavailable seconds-line since
|
|
last agent reset."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
|
|
::= { adslAtucPerfDataExtEntry 4 }
|
|
|
|
adslAtucPerfCurr15MinFastR OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAtucPerfCurr15MinFastR reports the current
|
|
number of seconds during which there have been
|
|
|
|
|
|
fast retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
|
|
::= { adslAtucPerfDataExtEntry 5 }
|
|
|
|
adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAtucPerfCurr15MinFailedFastR reports the
|
|
current number of seconds during which there
|
|
have been failed fast retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
|
|
::= { adslAtucPerfDataExtEntry 6 }
|
|
|
|
adslAtucPerfCurr15MinSesL OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAtucPerfCurr15MinSesL reports the current
|
|
number of seconds during which there have been
|
|
severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
|
|
::= { adslAtucPerfDataExtEntry 7 }
|
|
|
|
adslAtucPerfCurr15MinUasL OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAtucPerfCurr15MinUasL reports the current
|
|
number of seconds during which there have been
|
|
unavailable seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
|
|
::= { adslAtucPerfDataExtEntry 8 }
|
|
|
|
adslAtucPerfCurr1DayFastR OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
|
|
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAtucPerfCurr1DayFastR reports the number
|
|
of seconds during which there have been
|
|
fast retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
|
|
::= { adslAtucPerfDataExtEntry 9 }
|
|
|
|
adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAtucPerfCurr1DayFailedFastR reports the
|
|
number of seconds during which there have been
|
|
failed fast retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
|
|
::= { adslAtucPerfDataExtEntry 10 }
|
|
|
|
adslAtucPerfCurr1DaySesL OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAtucPerfCurr1DaySesL reports the
|
|
number of seconds during which there have been
|
|
severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
|
|
::= { adslAtucPerfDataExtEntry 11 }
|
|
|
|
adslAtucPerfCurr1DayUasL OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAtucPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAtucPerfCurr1DayUasL reports the
|
|
number of seconds during which there have been
|
|
unavailable seconds-line."
|
|
|
|
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
|
|
::= { adslAtucPerfDataExtEntry 12 }
|
|
|
|
adslAtucPerfPrev1DayFastR OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the previous day, adslAtucPerfPrev1DayFastR
|
|
reports the number of seconds during which there
|
|
were fast retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.1 "
|
|
::= { adslAtucPerfDataExtEntry 13 }
|
|
|
|
adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the previous day,
|
|
adslAtucPerfPrev1DayFailedFastR reports the number
|
|
of seconds during which there were failed fast
|
|
retrains."
|
|
REFERENCE "ITU G.997.1 Section 7.4.15.2 "
|
|
::= { adslAtucPerfDataExtEntry 14 }
|
|
|
|
adslAtucPerfPrev1DaySesL OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the previous day, adslAtucPerfPrev1DaySesL
|
|
reports the number of seconds during which there
|
|
were severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
|
|
::= { adslAtucPerfDataExtEntry 15 }
|
|
|
|
adslAtucPerfPrev1DayUasL OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the previous day, adslAtucPerfPrev1DayUasL
|
|
reports the number of seconds during which there
|
|
|
|
|
|
were unavailable seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.9 "
|
|
::= { adslAtucPerfDataExtEntry 16 }
|
|
|
|
adslAtucIntervalExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides one row for each ATU-C
|
|
performance data collection interval for
|
|
ADSL physical interfaces whose
|
|
IfEntries' ifType is equal to adsl(94)."
|
|
::= { adslExtMibObjects 19 }
|
|
|
|
adslAtucIntervalExtEntry OBJECT-TYPE
|
|
SYNTAX AdslAtucIntervalExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "An entry in the
|
|
adslAtucIntervalExtTable."
|
|
AUGMENTS { adslAtucIntervalEntry }
|
|
::= { adslAtucIntervalExtTable 1 }
|
|
|
|
AdslAtucIntervalExtEntry ::=
|
|
SEQUENCE {
|
|
adslAtucIntervalFastR PerfIntervalCount,
|
|
adslAtucIntervalFailedFastR PerfIntervalCount,
|
|
adslAtucIntervalSesL PerfIntervalCount,
|
|
adslAtucIntervalUasL PerfIntervalCount
|
|
}
|
|
|
|
adslAtucIntervalFastR OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current interval, adslAtucIntervalFastR
|
|
reports the current number of seconds during which
|
|
there have been fast retrains."
|
|
::= { adslAtucIntervalExtEntry 1 }
|
|
|
|
adslAtucIntervalFailedFastR OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
|
|
|
|
DESCRIPTION
|
|
"For the each interval, adslAtucIntervalFailedFastR
|
|
reports the number of seconds during which
|
|
there have been failed fast retrains."
|
|
::= { adslAtucIntervalExtEntry 2 }
|
|
|
|
adslAtucIntervalSesL OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the each interval, adslAtucIntervalSesL
|
|
reports the number of seconds during which
|
|
there have been severely errored seconds-line."
|
|
::= { adslAtucIntervalExtEntry 3 }
|
|
|
|
adslAtucIntervalUasL OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the each interval, adslAtucIntervalUasL
|
|
reports the number of seconds during which
|
|
there have been unavailable seconds-line."
|
|
::= { adslAtucIntervalExtEntry 4 }
|
|
|
|
adslAturPerfDataExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains ADSL physical line counters
|
|
not defined in the adslAturPerfDataTable
|
|
from the ADSL-LINE-MIB [RFC2662]."
|
|
::= { adslExtMibObjects 20 }
|
|
|
|
adslAturPerfDataExtEntry OBJECT-TYPE
|
|
SYNTAX AdslAturPerfDataExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry extends the adslAturPerfDataEntry defined
|
|
in [RFC2662]. Each entry corresponds to an ADSL
|
|
line."
|
|
AUGMENTS { adslAturPerfDataEntry }
|
|
::= { adslAturPerfDataExtTable 1 }
|
|
|
|
|
|
AdslAturPerfDataExtEntry ::=
|
|
SEQUENCE {
|
|
adslAturPerfStatSesL Counter32,
|
|
adslAturPerfStatUasL Counter32,
|
|
adslAturPerfCurr15MinSesL PerfCurrentCount,
|
|
adslAturPerfCurr15MinUasL PerfCurrentCount,
|
|
adslAturPerfCurr1DaySesL AdslPerfCurrDayCount,
|
|
adslAturPerfCurr1DayUasL AdslPerfCurrDayCount,
|
|
adslAturPerfPrev1DaySesL AdslPerfPrevDayCount,
|
|
adslAturPerfPrev1DayUasL AdslPerfPrevDayCount
|
|
}
|
|
|
|
adslAturPerfStatSesL OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
severely errored second-line since the last agent
|
|
reset."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.1.7 "
|
|
::= { adslAturPerfDataExtEntry 1 }
|
|
|
|
adslAturPerfStatUasL OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object reports the count of
|
|
unavailable seconds-line since the last agent
|
|
reset."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
|
|
::= { adslAturPerfDataExtEntry 2 }
|
|
|
|
adslAturPerfCurr15MinSesL OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAturPerfCurr15MinSesL reports the current
|
|
number of seconds during which there have been
|
|
severely errored seconds-line."
|
|
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
|
|
|
|
|
|
::= { adslAturPerfDataExtEntry 3 }
|
|
|
|
adslAturPerfCurr15MinUasL OBJECT-TYPE
|
|
SYNTAX PerfCurrentCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current 15-minute interval,
|
|
adslAturPerfCurr15MinUasL reports the current
|
|
number of seconds during which there have been
|
|
available seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
|
|
::= { adslAturPerfDataExtEntry 4 }
|
|
|
|
adslAturPerfCurr1DaySesL OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAturPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAturPerfCurr1DaySesL reports the
|
|
number of seconds during which there have been
|
|
severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
|
|
::= { adslAturPerfDataExtEntry 5 }
|
|
|
|
adslAturPerfCurr1DayUasL OBJECT-TYPE
|
|
SYNTAX AdslPerfCurrDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the current day as measured by
|
|
adslAturPerfCurr1DayTimeElapsed [RFC2662],
|
|
adslAturPerfCurr1DayUasL reports the
|
|
number of seconds during which there have been
|
|
unavailable seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
|
|
::= { adslAturPerfDataExtEntry 6 }
|
|
|
|
adslAturPerfPrev1DaySesL OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
|
|
|
|
DESCRIPTION
|
|
"For the previous day, adslAturPerfPrev1DaySesL
|
|
reports the number of seconds during which there
|
|
were severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.7 "
|
|
::= { adslAturPerfDataExtEntry 7 }
|
|
|
|
adslAturPerfPrev1DayUasL OBJECT-TYPE
|
|
SYNTAX AdslPerfPrevDayCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the previous day, adslAturPerfPrev1DayUasL
|
|
reports the number of seconds during which there
|
|
were severely errored seconds-line."
|
|
REFERENCE "ITU G.997.1 Section 7.2.1.2.9 "
|
|
::= { adslAturPerfDataExtEntry 8 }
|
|
|
|
adslAturIntervalExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslAturIntervalExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides one row for each ATU-R
|
|
performance data collection interval for
|
|
ADSL physical interfaces whose
|
|
IfEntries' ifType is equal to adsl(94)."
|
|
::= { adslExtMibObjects 21 }
|
|
|
|
adslAturIntervalExtEntry OBJECT-TYPE
|
|
SYNTAX AdslAturIntervalExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "An entry in the
|
|
adslAturIntervalExtTable."
|
|
AUGMENTS { adslAturIntervalEntry }
|
|
::= { adslAturIntervalExtTable 1 }
|
|
|
|
AdslAturIntervalExtEntry ::=
|
|
SEQUENCE {
|
|
adslAturIntervalSesL PerfIntervalCount,
|
|
adslAturIntervalUasL PerfIntervalCount
|
|
}
|
|
|
|
adslAturIntervalSesL OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
|
|
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the each interval, adslAturIntervalSesL
|
|
reports the number of seconds during which
|
|
there have been severely errored seconds-line."
|
|
::= { adslAturIntervalExtEntry 1 }
|
|
|
|
adslAturIntervalUasL OBJECT-TYPE
|
|
SYNTAX PerfIntervalCount
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"For the each interval, adslAturIntervalUasL
|
|
reports the number of seconds during which
|
|
there have been unavailable seconds-line."
|
|
::= { adslAturIntervalExtEntry 2 }
|
|
|
|
adslConfProfileExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslConfProfileExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The adslConfProfileExtTable extends the ADSL line
|
|
profile configuration information in the
|
|
adslLineConfProfileTable from the ADSL-LINE-MIB
|
|
[RFC2662] by adding the ability to configure the
|
|
ADSL physical line mode."
|
|
::= { adslExtMibObjects 22 }
|
|
|
|
adslConfProfileExtEntry OBJECT-TYPE
|
|
SYNTAX AdslConfProfileExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry extends the adslLineConfProfileEntry
|
|
defined in [RFC2662]. Each entry corresponds to an
|
|
ADSL line profile."
|
|
AUGMENTS { adslLineConfProfileEntry }
|
|
::= { adslConfProfileExtTable 1 }
|
|
|
|
AdslConfProfileExtEntry ::=
|
|
SEQUENCE {
|
|
adslConfProfileLineType INTEGER
|
|
}
|
|
|
|
adslConfProfileLineType OBJECT-TYPE
|
|
|
|
|
|
SYNTAX INTEGER {
|
|
noChannel (1), -- no channels exist
|
|
fastOnly (2), -- only fast channel exists
|
|
interleavedOnly (3), -- only interleaved channel
|
|
-- exist
|
|
fastOrInterleaved (4),-- either fast or interleaved
|
|
-- channels can exist, but
|
|
-- only one at any time
|
|
fastAndInterleaved (5)-- both the fast channel and
|
|
-- the interleaved channel
|
|
-- exist
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to configure the ADSL physical
|
|
line mode. It has following valid values:
|
|
|
|
noChannel(1), when no channels exist.
|
|
fastOnly(2), when only fast channel exists.
|
|
interleavedOnly(3), when only interleaved channel
|
|
exist.
|
|
fastOrInterleaved(4), when either fast or
|
|
interleaved channels can exist, but only one
|
|
at any time.
|
|
fastAndInterleaved(5), when both the fast channel
|
|
and the interleaved channel exist.
|
|
|
|
In the case when no value has been set, the default
|
|
Value is noChannel(1).
|
|
"
|
|
DEFVAL { fastOnly }
|
|
::= { adslConfProfileExtEntry 1 }
|
|
|
|
adslAlarmConfProfileExtTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table extends the
|
|
adslLineAlarmConfProfileTable and provides
|
|
threshold parameters for all the counters defined
|
|
in this MIB module."
|
|
::= { adslExtMibObjects 23 }
|
|
|
|
adslAlarmConfProfileExtEntry OBJECT-TYPE
|
|
SYNTAX AdslAlarmConfProfileExtEntry
|
|
MAX-ACCESS not-accessible
|
|
|
|
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry extends the adslLineAlarmConfProfileTable
|
|
defined in [RFC2662]. Each entry corresponds to
|
|
an ADSL alarm profile."
|
|
AUGMENTS { adslLineAlarmConfProfileEntry }
|
|
::= { adslAlarmConfProfileExtTable 1 }
|
|
|
|
AdslAlarmConfProfileExtEntry ::=
|
|
SEQUENCE {
|
|
adslAtucThreshold15MinFailedFastR Integer32,
|
|
adslAtucThreshold15MinSesL Integer32,
|
|
adslAtucThreshold15MinUasL Integer32,
|
|
adslAturThreshold15MinSesL Integer32,
|
|
adslAturThreshold15MinUasL Integer32
|
|
}
|
|
|
|
adslAtucThreshold15MinFailedFastR OBJECT-TYPE
|
|
SYNTAX Integer32(0..900)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The first time the value of the corresponding
|
|
instance of adslAtucPerfCurr15MinFailedFastR
|
|
reaches or exceeds this value within a given
|
|
15-minute performance data collection period,
|
|
an adslAtucFailedFastRThreshTrap notification
|
|
will be generated. The value '0' will disable
|
|
the notification. The default value of this
|
|
object is '0'."
|
|
DEFVAL { 0 }
|
|
::= { adslAlarmConfProfileExtEntry 1 }
|
|
|
|
adslAtucThreshold15MinSesL OBJECT-TYPE
|
|
SYNTAX Integer32(0..900)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The first time the value of the corresponding
|
|
instance of adslAtucPerf15MinSesL reaches or
|
|
exceeds this value within a given 15-minute
|
|
performance data collection period, an
|
|
adslAtucSesLThreshTrap notification will be
|
|
generated. The value '0' will disable the
|
|
notification. The default value of this
|
|
object is '0'."
|
|
|
|
|
|
DEFVAL { 0 }
|
|
|
|
::= { adslAlarmConfProfileExtEntry 2 }
|
|
|
|
adslAtucThreshold15MinUasL OBJECT-TYPE
|
|
SYNTAX Integer32(0..900)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The first time the value of the corresponding
|
|
instance of adslAtucPerf15MinUasL reaches or
|
|
exceeds this value within a given 15-minute
|
|
performance data collection period, an
|
|
adslAtucUasLThreshTrap notification will be
|
|
generated. The value '0' will disable the
|
|
notification. The default value of this
|
|
object is '0'."
|
|
DEFVAL { 0 }
|
|
::= { adslAlarmConfProfileExtEntry 3 }
|
|
|
|
adslAturThreshold15MinSesL OBJECT-TYPE
|
|
SYNTAX Integer32(0..900)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The first time the value of the corresponding
|
|
instance of adslAturPerf15MinSesL reaches or
|
|
exceeds this value within a given 15-minute
|
|
performance data collection period, an
|
|
adslAturSesLThreshTrap notification will be
|
|
generated. The value '0' will disable the
|
|
notification. The default value of this
|
|
object is '0'."
|
|
DEFVAL { 0 }
|
|
::= { adslAlarmConfProfileExtEntry 4 }
|
|
|
|
adslAturThreshold15MinUasL OBJECT-TYPE
|
|
SYNTAX Integer32(0..900)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The first time the value of the corresponding
|
|
instance of adslAturPerf15MinUasL reaches or
|
|
exceeds this value within a given 15-minute
|
|
performance data collection period, an
|
|
|
|
|
|
adslAturUasLThreshTrap notification will be
|
|
generated. The value '0' will disable the
|
|
notification. The default value of this
|
|
object is '0'."
|
|
DEFVAL { 0 }
|
|
|
|
::= { adslAlarmConfProfileExtEntry 5 }
|
|
|
|
-- definitions
|
|
|
|
adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 }
|
|
|
|
adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 }
|
|
|
|
adslExtAtucTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAtucTraps 0 }
|
|
|
|
adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE
|
|
OBJECTS { adslAtucPerfCurr15MinFailedFastR }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Failed Fast Retrains 15-minute threshold reached."
|
|
::= { adslExtAtucTrapsPrefix 1 }
|
|
|
|
adslAtucSesLThreshTrap NOTIFICATION-TYPE
|
|
OBJECTS { adslAtucPerfCurr15MinSesL }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Severely errored seconds-line 15-minute threshold
|
|
reached."
|
|
::= { adslExtAtucTrapsPrefix 2 }
|
|
|
|
adslAtucUasLThreshTrap NOTIFICATION-TYPE
|
|
OBJECTS { adslAtucPerfCurr15MinUasL }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Unavailable seconds-line 15-minute threshold
|
|
reached."
|
|
::= { adslExtAtucTrapsPrefix 3 }
|
|
|
|
adslExtAturTraps OBJECT IDENTIFIER ::= { adslExtTraps 2 }
|
|
|
|
adslExtAturTrapsPrefix OBJECT IDENTIFIER ::= { adslExtAturTraps 0 }
|
|
|
|
adslAturSesLThreshTrap NOTIFICATION-TYPE
|
|
OBJECTS { adslAturPerfCurr15MinSesL }
|
|
STATUS current
|
|
DESCRIPTION
|
|
|
|
|
|
"Severely errored seconds-line 15-minute threshold
|
|
reached."
|
|
::= { adslExtAturTrapsPrefix 1 }
|
|
|
|
adslAturUasLThreshTrap NOTIFICATION-TYPE
|
|
OBJECTS { adslAturPerfCurr15MinUasL }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Unavailable seconds-line 15-minute threshold
|
|
reached."
|
|
::= { adslExtAturTrapsPrefix 2 }
|
|
|
|
-- conformance information
|
|
|
|
adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 }
|
|
|
|
adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 }
|
|
adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 }
|
|
|
|
-- ATU-C agent compliance statements
|
|
|
|
adslExtLineMibAtucCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for SNMP entities which
|
|
represent ADSL ATU-C interfaces."
|
|
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS
|
|
{
|
|
adslExtLineGroup,
|
|
adslExtLineConfProfileControlGroup,
|
|
adslExtLineAlarmConfProfileGroup
|
|
}
|
|
|
|
GROUP adslExtAtucPhysPerfCounterGroup
|
|
DESCRIPTION
|
|
"This group is optional. Implementations which
|
|
require continuous ATU-C physical event counters
|
|
should implement this group."
|
|
|
|
GROUP adslExtAturPhysPerfCounterGroup
|
|
DESCRIPTION
|
|
"This group is optional. Implementations which
|
|
require continuous ATU-R physical event counters
|
|
should implement this group."
|
|
|
|
|
|
GROUP adslExtNotificationsGroup
|
|
DESCRIPTION
|
|
"This group is optional. Implementations which
|
|
support TCA (Threshold Crossing Alert) should
|
|
implement this group."
|
|
|
|
OBJECT adslAtucThreshold15MinFailedFastR
|
|
MIN-ACCESS read-write
|
|
DESCRIPTION
|
|
"Read-write access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
OBJECT adslAtucThreshold15MinSesL
|
|
MIN-ACCESS read-write
|
|
DESCRIPTION
|
|
"Read-write access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
OBJECT adslAtucThreshold15MinUasL
|
|
MIN-ACCESS read-write
|
|
DESCRIPTION
|
|
"Read-write access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
OBJECT adslAturThreshold15MinSesL
|
|
MIN-ACCESS read-write
|
|
DESCRIPTION
|
|
"Read-write access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
OBJECT adslAturThreshold15MinUasL
|
|
MIN-ACCESS read-write
|
|
DESCRIPTION
|
|
"Read-write access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
OBJECT adslLineConfProfileDualLite
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Read-only access is applicable only when
|
|
static profiles as defined in ADSL Line MIB
|
|
[RFC2662] are implemented."
|
|
|
|
|
|
::= { adslExtCompliances 1 }
|
|
|
|
-- units of conformance
|
|
adslExtLineGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
adslLineConfProfileDualLite,
|
|
adslLineTransAtucCap,
|
|
adslLineTransAtucConfig,
|
|
adslLineTransAtucActual,
|
|
adslLineGlitePowerState
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing extended
|
|
configuration information about an ADSL Line."
|
|
::= { adslExtGroups 1 }
|
|
|
|
adslExtAtucPhysPerfCounterGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
adslAtucPerfStatFastR,
|
|
adslAtucPerfStatFailedFastR,
|
|
adslAtucPerfCurr15MinFastR,
|
|
adslAtucPerfCurr15MinFailedFastR,
|
|
adslAtucPerfCurr1DayFastR,
|
|
adslAtucPerfCurr1DayFailedFastR,
|
|
adslAtucPerfPrev1DayFastR,
|
|
adslAtucPerfPrev1DayFailedFastR,
|
|
adslAtucPerfStatSesL,
|
|
adslAtucPerfStatUasL,
|
|
adslAtucPerfCurr15MinSesL,
|
|
adslAtucPerfCurr15MinUasL,
|
|
adslAtucPerfCurr1DaySesL,
|
|
adslAtucPerfCurr1DayUasL,
|
|
adslAtucPerfPrev1DaySesL,
|
|
adslAtucPerfPrev1DayUasL,
|
|
adslAtucIntervalFastR,
|
|
adslAtucIntervalFailedFastR,
|
|
adslAtucIntervalSesL,
|
|
adslAtucIntervalUasL
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing raw performance
|
|
counts on an ADSL Line (ATU-C end)."
|
|
::= { adslExtGroups 2 }
|
|
|
|
adslExtAturPhysPerfCounterGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
|
|
|
|
adslAturPerfStatSesL,
|
|
adslAturPerfStatUasL,
|
|
adslAturPerfCurr15MinSesL,
|
|
adslAturPerfCurr15MinUasL,
|
|
adslAturPerfCurr1DaySesL,
|
|
adslAturPerfCurr1DayUasL,
|
|
adslAturPerfPrev1DaySesL,
|
|
adslAturPerfPrev1DayUasL,
|
|
adslAturIntervalSesL, adslAturIntervalUasL
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing raw performance
|
|
counts on an ADSL Line (ATU-C end)."
|
|
::= { adslExtGroups 3 }
|
|
|
|
adslExtLineConfProfileControlGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
adslConfProfileLineType
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing profile
|
|
control for the ADSL system."
|
|
::= { adslExtGroups 4 }
|
|
|
|
adslExtLineAlarmConfProfileGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
adslAtucThreshold15MinFailedFastR,
|
|
adslAtucThreshold15MinSesL,
|
|
adslAtucThreshold15MinUasL,
|
|
adslAturThreshold15MinSesL,
|
|
adslAturThreshold15MinUasL
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing alarm profile
|
|
control for the ADSL system."
|
|
::= { adslExtGroups 5 }
|
|
|
|
adslExtNotificationsGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
adslAtucFailedFastRThreshTrap,
|
|
adslAtucSesLThreshTrap,
|
|
adslAtucUasLThreshTrap,
|
|
adslAturSesLThreshTrap,
|
|
adslAturUasLThreshTrap
|
|
}
|
|
|
|
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The collection of ADSL extension notifications."
|
|
::= { adslExtGroups 6 }
|
|
|
|
END
|